Allied Telesis AT FS709FC AT-FS709FC AT-FS709FC Installation guide

AT-FS709FC
10/100 Fast Ethernet Unmanaged
Switch
Installation Guide
PN 613-10817-00 Rev. A
Copyright 1999 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94086, USA
All rights reserved. No part of this publication may be reproduced without prior written permission
from AlliedTelesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their
respective owners.
AlliedTelesyn International, Corp. reserves the right to make changes in specifications and other
information contained in this document without prior written notice. The information provided
herein is subject to change without notice. In no event shall AlliedTelesyn International, Corp. be
liable for any incidental, special, indirect, or consequential damages whatsoever, including but not
limited to lost profits, arising out of or related to this manual or the information contained herein,
even if AlliedTelesyn International, Corp. has been advised of, known, or should have known, the
possibility of such damages.
Safety Warnings
STANDARDS: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Manufacture Address:
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Fast Ethernet Unmanaged Switch
Model Number:
AT-FS709FC
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device must not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant of
this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.
Canadian Department of Communications
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
iii
Safety Warnings
WARNING: In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
IMPORTANT: Appendix A contains translated safety statements for installing this equipment.
Go to Appendix A for the translated safety statement in your language.
WICHTIG: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses
Geräts. Schlagen Sie in Anhang A den übersetzten Sicherheitshinweis in Ihrer Sprache nach.
VIGTIGT: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af
dette udstyr. Skal De slå op i tillæg A og finde de oversatte sikkerhedsadvarsler i Deres eget
sprog.
BELANGRIJK: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van
deze apparatuur. Raadpleeg Appendix A voor vertaalde veiligheidsinstructies in uw taal.
IMPORTANT: L'annexe A contient les instructions de sécurité relatives à l'installation de cet
équipement. Reportez-vous à l'annexe A pour consulter la traduction de ces instructions
dans votre langue.
TÄRKEÄÄ: Liite A sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet. Katso
käännettyä turvaohjetta liitteestä A.
IMPORTANTE: l’Appendice A contiene avvisi di sicurezza tradotti per l’installazione di questa
apparecchiatura. Indica di consultare l’Appendice A per l’avviso di sicurezza nella propria
lingua.
VIKTIG: Tillegg A inneholder oversatt sikkerhetsinformasjon for installering av dette
utstyret. åpner du til Tillegg A for å finne den oversatte sikkerhetsinformasjonen på ønsket
språk.
IMPORTANTE: O Anexo A contém advertências de segurança traduzidas para instalar este
equipamento. Leia a advertência de segurança traduzida no seu idioma no Anexo A.
IMPORTANTE: El Apéndice A contiene mensajes de seguridad traducidos para la instalación
de este equipo. Vaya al Apéndice A para ver el mensaje de seguridad traducido a su idioma.
OBS! Bilaga A innehåller översatta säkerhetsmeddelanden avseende installationen av denna
utrustning. Skall du gå till Bilaga A för att läsa det översatta säkerhetsmeddelandet på ditt
språk.
iv
Table of Contents
Safety Warnings ................................................................................................................... iii
Chapter
Product Description ..............................................................................................................1
Overview ..................................................................................................................................1
Description ..............................................................................................................................2
Connectors ......................................................................................................................2
LEDs ................................................................................................................................3
MDI/MDI-X Port 8 ........................................................................................................4
Power Supply ..................................................................................................................4
Auto-Negotiation ....................................................................................................................4
Chapter
Installation .............................................................................................................................5
Before you Proceed .................................................................................................................5
Verifying Package Contents....................................................................................................5
Site Requirements ...................................................................................................................6
Desktop Installation ................................................................................................................6
Rackmount Installation ..........................................................................................................7
Standalone Configuration ......................................................................................................8
Cascade Configuration ...........................................................................................................9
Uplink Configuration ...........................................................................................................10
Chapter
Troubleshooting ..................................................................................................................11
Connectivity Testing .............................................................................................................11
Problem Solving ....................................................................................................................12
Is the unit receiving power?..........................................................................................12
Is the Link/Activity LED lit? .........................................................................................12
Appendix A
Electrical Safety and Installation Requirement ................................................................15
Appendix B
Switch Specifications ...........................................................................................................29
Physical Characteristics.........................................................................................................29
Safety Agency.........................................................................................................................29
Cable Specifications ..............................................................................................................30
v
Appendix C
Technical Support Fax Order .............................................................................................31
Incident Summary.................................................................................................................31
Appendix D
AT-FS709FC Installation Feedback ....................................................................................33
Appendix E
Where To Find Us ................................................................................................................35
vi
Chapter 1
Product Description
Overview
The AT-FS709FC is a nine port Fast Ethernet switch with eight auto-negotiating 10Base-T/
100Base-TX shielded twisted pair RJ45 ports and one 100Base-FX(SC) fiber port. The
switch features include:
!
IEEE 802.3, IEEE 802.3u and IEEE 802.3x compliant
!
Store and forward switching at full-wire speed (14,880 packets per second on
10 Mbps ports and 148,800 packets per second on 100 Mbps ports)
!
Support for up to 8K MAC addresses
!
Link/Activity, Transmission speed, and Full-/Half-duplex LEDs for each port
!
Eight auto-negotiating 10/100 Mbps RJ45 ports that can be connected/
disconnected without powering off the switch.
!
Media-dependent interface (MDI/MDI-X) connectors for Port 8 for user
selectable hub or PC connection
!
One full-duplex 100Base-FX port
!
Internal power supply (100-120/200-240 VAC)
This switch complements the other Allied Telesyn Fast Ethernet products, providing
simple, cost-effective solutions for switching between 10 and 1 0 0 M bps. Easy to install,
simply plug in the power cord and connect your station ports.
Note
For definitions of technical terms associated with Allied Telesyn’s products, refer
to the Glossary on Allied Telesyn’s website at www.alliedtelesyn.com.
1
Product Description
Figure 1 shows the switch front panel.
TX
RX
Figure 1 AT-FS709FC Front Panel
Description
This section includes:
!
Connectors
!
LEDs
!
MDI/MDI-X Port 8
!
Power Supply
!
Auto-negotiation
Connectors
Table 1 lists and defines the type of connectors available and their function.
Table 1 Connector Types on Switch
Connector Type
2
Function
Ports 1 through 7
10/100Base-TX, RJ45
connectors
Connect to a high-performance workstation, server or
hub
Port 8 MDI/MDI-X
10/100Base-TX, RJ45
connector
MDI Port: Cascade or uplink port
Port 9
100Base-FX, SC connectors
Full-duplex cascade or uplink port to server or switch
MDI-X: Connect to a high-performance workstation,
server or hub
AT-FS709FC Installation Guide
LEDs
Figure 2 illustrates the switch front panel LEDs. Table 2 lists and describes these LEDs.
Power
Link/Act
100M
FDX
1
2
3
4
5
6
7
8
9
Figure 2 A Close Up of the Front Panel LEDs
Table 2 LED Status
LEDs
Color
LINK/ACTIVITY
Green
Description
On indicates a valid physical link on the port.
Blinking indicates data is being transmitted.
Off means no link.
100M
Green
On means the bandwidth is 100 Mbps.
Off means the bandwidth is 10 Mbps.
(Off does not apply to Port 9.)
FDX (FULL-DUPLEX)
Green
On indicates full-duplex transmission mode.
Off indicates half-duplex transmission mode.
(Off does not apply to Port 9.)
POWER
Green
On means there is power to the switch.
Off means there is no power to the switch.
3
Product Description
MDI/MDI-X Port 8
Port 8 is associated with the MDI function.
Port 8 gives you the flexibility of using a straight-through cable to connect to a hub or
another switch (Port 8 MDI), or to any DTE device (Port 8 MDI-X), such as an end station
or a server.
Note
Use only one Port 8, either Port 8 MDI or Port 8 MDI-X.
Table 3 MDI Ports
Port
Port 8 MDI
Port 8 MDI-X
Use
To connect a hub or another switch to the port
To connect a DTE to the port
Power Supply
The switch uses a universal internal switching power supply with 100 to 120 VAC, or 200 to
240 VAC, 50/60 Hz input rating.
Auto-Negotiation
Auto-negotiation is an optional function of the IEEE 802.3u Fast Ethernet standard that
enables devices to automatically exchange information over a link about their speed and
duplex abilities. This allows the devices to perform automatic configurations to achieve the
maximum common level of operation over a link.
The eight (RJ45) 10Base-T/100Base-TX ports on the switch use auto-negotiation for speed
and duplex settings. This means these ports automatically adapt to the wire speed (10 or 100
Mbps) and duplex transmission (half- or full-duplex) supported by the link without user
reconfiguration. Port 9 (fiber) is a 100Base-FX port that always operates at 100 Mbps, and
full-duplex transmission mode.
4
Chapter 2
Installation
Before you Proceed
Before installing the switch, make sure you read “Electrical Safety and Installation
Requirements” on page 15.
Verifying Package Contents
Make sure that the package includes the following items:
!
One AT-FS709FC switch
!
One AC power cord (for the U.S., Continental Europe, and the U.K. versions
only)
!
Two rackmounting brackets with screws
!
Four self-adhesive rubber feet
!
Warranty card
!
This installation guide
If any of the above items is damaged or missing, contact your representative immediately.
5
Installation
Site Requirements
Make sure you observe the following site requirements:
!
Make sure you are placing the switch in a dust-free and moisture-free
environment.
!
Do not block ventilation openings on the unit.
!
Make sure that the switch’s power is accessible and cables can be connected easily.
!
Cabling should be away from sources of electrical noise such as radios,
transmitters, broadband amplifiers, power lines and fluorescent fixtures.
!
Do not place objects on top of the switch.
!
Use dedicated power circuits or power conditioners to supply power to the
switch.
Desktop Installation
Place the switch on the desktop using these steps, or perform the steps “Rackmount
Installation” on page 7. The AT-FS709FC can be stacked two or more devices high on the
desktop as described in the steps below.
1.
Attach the four self-adhesive rubber feet to the bottom of the switch, positioning
them in the indentations.
2.
Place the switch on a flat, level surface where power is easily accessible.
3.
To stack more than one switch, repeat step 1 for the additional switches before
stacking them. The rubber feet cushion the switch against shock and vibration
and provide space between each switch for ventilation.
4.
Connect power: attach one end of the power cord to the back of the switch and
the other end to the power source.
Note
The switch performs a self-diagnostic test upon power on, and takes about 20
seconds to complete.
5.
6
Make sure the Power LED on the front panel lights green.
AT-FS709FC Installation Guide
Note
Do not plug a phone jack connector into any RJ45 port. This may damage the
switch. Use only twisted-pair cables with RJ45 connectors that conform with FCC
standards.
6.
Attach the data cables and observe normal operation as indicated by the port
LEDs. Use only one Port 8, either Port 8 MDI or Port 8 MDI-X.
7.
Attach fiber optic cable with SC connectors to Port 9 and observe LEDs for
normal operation.
Note
Auto-negotiation for transmission mode supports full-duplex only if the
connected device also negotiates for full-duplex transmission mode. Port 9
supports full-duplex operation only
You are finished with desktop installation.
Rackmount Installation
You will need a Phillips screwdriver for this installation.
Caution
Do not use power tools to perform this installation.
1.
If previously attached, remove the rubber feet and all cables and power cord from
the switch.
2.
Attach the rackmounting brackets to each side of the switch, using the screws
provided.
3.
Attach the power cord to the back of the switch.
4.
Position the switch in a standard 19-inch rack and secure the switch’s brackets to
the rack using the 4 large screws provided.
5.
Plug the power cord into the power receptacle. Make sure the Power LED on the
front panel lights green.
Note
Do not plug a phone jack connector into any RJ45 port. This may damage the
switch. Use only twisted-pair cables with RJ45 connectors that conform with FCC
standards.
7
Installation
6.
Attach the data cables and observe normal operation as indicated by the port
LEDs. Use only one Port 8, either Port 8 MDI or Port 8 MDI-X. For typical
configuration information, refer to “Cascade Configuration” on page 9.
7.
Attach fiber optic cable with SC connectors to Port 9 and observe LEDs for
normal operation.
Note
Auto-negotiation for transmission mode supports full-duplex only if the
connected device also negotiates for full-duplex transmission mode. Port 9
supports full-duplex operation only.
You are finished with rackmount installation.
Standalone Configuration
In a standalone configuration, the switch supports up to 9 network nodes. Figure 3 shows a
switch connected to end stations and a server. The basic physical connection for this
configuration requires connecting one of the switch’s ports to the adapter card of an end
station.
TX
Full-Duplex
Copper
Fiber
Figure 3 AT-FS709FC Connected to End Stations
8
RX
AT-FS709FC Installation Guide
Cascade Configuration
Cascading means that two switches can be connected together using any of the switch ports,
provided you maintain the same media type. Two switches can be cascaded to support
multiple network port connections. Cable length to the nodes must follow the 100Base-TX
cabling specifications.
To cascade installed switches, do the following:
Note
When cascading switches, you must use the same media type from port to port.
1.
If you intend to use Port 8, use Port 8 MDI.
2.
Use a straight-through UTP RJ45 cable to connect the first switch to the second
switch. See Figure4.
Copper
Fiber
TX
RX
TX
RX
Full-Duplex
Figure 4 Cascading Switches
3.
Check the front panels to make sure that the Link/Activity LED lights.
9
Installation
Uplink Configuration
For 100 Mbps connection to the backbone, use Port 9. Figure5 illustrates how this switch
can be used as a full-duplex uplink to the backbone in a typical office complex using Fiber
cable.
TX
RX
10BASE-T / 100BASE-TX
FAST ETHERNET SWITCH
MDA
10BASE-T / 100BASE-TX
A
B
RS-232
TERMINAL PORT
PORT ACTIVITY
1X
3X
5X
7X
9X
11X
13X
15X
17X
19X
21X
23X
2X
4X
6X
8X
10X
12X
14X
16X
18X
20X
22X
24X
LINK /
RECEIVE
STATUS
100M
1
3
5
7
9
11
13
15
17
19
21
23
2
4
6
8
10
12
14
16
18
20
22
24
FAULT
A
B
POWER
RESET
TX
RX
Copper
Fiber
Figure 5 AT-FS709FC Switches Connected to the Backbone
10
Chapter 3
Troubleshooting
This chapter describes the procedures to test and troubleshoot the switches.
Connectivity Testing
In the following procedure, you will test each port for a valid connection and to confirm the
correct operation of the network.
1.
Start with Ports 1 and 2. Connect these two ports of a single switch to two nodes
or workstations and turn on the switch power.
2.
Wait approximately 1-3 seconds for the auto-negotiation process to complete
after power-on or after the cables are reconnected.
3.
Make sure the Link/Activity and other LEDs of both switch ports are lit.
4.
After confirming that Port 1 and Port 2 are operational, reconnect one of the
nodes/workstations to another port, then repeat this connectivitiy test with the
switch’s remaining ports. Continue to verify the connection in each port by
checking the Link/Activity and other activity LEDs.
Note
Use Port 8 MDI-X connected to a workstation. Use Port 8 MDI connected to a
hub. Use only one Port 8 at a time.
11
Troubleshooting
Problem Solving
Is the unit receiving power?
Check the Power LED on the front of the switch. This green LED should be lit.
Note
The switch performs a self-diagnostic test upon power on, and takes about 20
seconds to complete.
If the Power LED is not on, check both ends of the power cord or adapter. Make sure the
power cord or adapter is plugged into a functioning wall outlet and that it is properly
inserted into the switch’s connector on the back of the unit.
Is the Link/Activity LED lit?
The Link LED on the front of the switch lights when a proper connection between the
corresponding 10/100Base-TX port and the equipment connected to it is established. If this
LED is not lit, check for the problems listed below and make corrections as necessary.
1.
Problem 1:
The cable has been cut, damaged, or it is the wrong type of cable.
!
Solution 1:
—
2.
Try making the connection with a different cable. Be sure you are using
an undamaged cable of the correct type.
Problem 2:
Connected equipment is not turned on or not operating properly.
!
Solution 2:
—
3.
Check the connected equipment (computer, another switch, etc.) and
turn on the power.
Problem 3:
Port 8 does not work.
!
Solution 3:
—
12
Connect to only one Port 8, either Port 8 MDI or Port 8 MDI-X. Make
sure you are connected to the correct Port 8.
AT-FS709FC Installation Guide
4.
Problem 4:
There is data loss between the switch and one of the connected network nodes.
!
Solution 4:
—
Make sure that the distance between the switch and the connected
network device is no greater than 100 m (328 ft).
—
Make sure you are using Category 5 cable.
13
Appendix A
Electrical Safety and Installation
Requirements
STANDARDS: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Manufacture Address:
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Fast Ethernet Unmanaged Switch
Model Number:
AT-FS709FC
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device must not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant of
this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.
15
Electrical Safety and Installation Requirements
Canadian Department of Communications
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
RADIATED ENERGY
RFI Emission
EN55022 Class B
WARNING: This product requires shielded cables to comply with Class B emission limits. If
not used with shielded cables, this product may cause radio interference in which case the
user may be required to take adequate measures.
Immunity
EN50082-1
Electrical Safety
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SAFETY
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock, do not remove cover. No user-serviceable parts inside. This
unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified
technician. To avoid the possibility of ELECTRIC SHOCK disconnect electric power to the
product before connecting or disconnecting the LAN cables.
This is a “CLASS 1 LED PRODUCT”
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DE-ENERGISE
EQUIPMENT disconnect the power cord.
INSTALLATION
ELECTRICAL - AUTO VOLTAGE ADJUSTMENT
This product will automatically adjust to any voltage between the ranges shown on the label.
ELECTRICAL - TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly wired
earth ground socket outlet. An improperly wired socket outlet could place hazardous
voltages on accessible metal parts.
ELECTRICAL - CORD NOTICE
Use power cord, maximum 4.5 meters long, rated 5 amp minimum, 250V,made of <HAR>
cordage molded IEC 320 connector on one end and on the other end a plug approved by the
country of end use.
16
AT-FS709FC Installation Guide
CAUTION: Air vents must not be blocked and must have free access to the room ambient air
for cooling.
OPERATING TEMPERATURE
This product is designed for a maximum ambient temperature of 40 degrees C.
ALL COUNTRIES: Install product in accordance with local and National Electrical Codes.
NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Hochfrequenzstörung
EN55022 Klasse B
WARNUNG: Dieses Produkt muß mit entstörten Kabeln versehen sein, damit es den
Emissionsgrenzen der Klasse B entspricht. Wenn dieses Produkt nicht mit entstörten Kabeln
verwendet wird, könnte es Funkstörungen hervorrufen; der Anwender müßte in diesem Fall
angemessene Gegenmaßnahmen ergreifen.
Störsicherheit
EN50082-1
Elektrische Sicherheit
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SICHERHEIT
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile. Das Gerät
steht unter Hochspannung und darf nur von qualifiziertem technischem Personal geöffnet
werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.
Das ist ein “LED Produkt der Klasse 1”
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters ausführen.
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER STROMVERSORGUNG. ZUR
TRENNUNG VOM NETZ, KABEL AUS DER STECKDOSE ZIEHEN.
INSTALLATION
AUTOMATISCHE SPANNUNGSEINSTELLUNG
Dieses Gerät stellt sich automatisch auf die auf dem Etikett aufgeführten Spannungswerte
ein.
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer vorschriftsmäßig
geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger Anschluß kann die Metallteile
des Gehauses unter gefährliche elektrische Spannungen setzen.
NETZKABEL
Das Netzkabel sollte eine maximale Länge von 4,5 Metern, einen Nennwert von mindestens
5 A und 250 V haben, aus HAR-Material hergestellt und mit einer gepreßten, IEC320
entsprechenden, Anschlußverbindung an einem Ende, und am anderen Ende mit einem im
Land des Endverbrauchers geprüften Stecker ausgestattet sein.
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.
17
Electrical Safety and Installation Requirements
BETRIEBSTEMPERATUR
Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als
40° C entworfen.
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften
entsprechen.
STANDARDER: Dette produkt tilfredsstiller de følgende standarder.
Radiofrekvens forstyrrelsesemission
EN55022 Klasse B
ADVARSEL: Der skal bruges skærmkabler med dette produkt for at opfylde Klasse B
emissionsgrænser. Hvis skærmkabler ikke bruges, kan dette produkt muligvis forårsage
radio forstyrrelse. Bliver dette tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.
Immunitet
EN50082-1
Elektrisk sikkerhed
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SIKKERHED
ELEKTRISKE FORHOLDSREGLER ADVARSEL: RISIKO FOR ELEKTRISK STØD For at
forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan
repareres af brugeren. Denne enhed indeholder LIVSFARLIGE STRØMSPÆNDINGER og
bør kun åbnes af en uddannet og kvalificeret tekniker. For at undgå risiko for ELEKTRISK
STØD, afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres eller
afmonteres.
Dette er et “PRODUKT UNDER KLASSE 1 LED”
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN.
SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud af stikket.
INSTALLATION
ELEKTRISK - AUTOMATISK SPÆNDINGSREGULERING
Dette apparat vil automatisk tilpasse sig enhver spænding indenfor de værdier, der er angivet
på etiketten.
ELEKTRISK - KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt
installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan sætte livsfarlig
spænding til tilgængelige metaldele.
ELEKTRISK - LEDNING
Anvend ledning af maksimum 4,5 meters længde, med en kapacitet på minimum 5 amp.,
250 v, bestående af en IEC 320 connector med indstøbt <HAR> ledning i den ene ende og et
stik i den anden ende, der er godkendt af myndighederne i brugerlandet.
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
18
AT-FS709FC Installation Guide
BETJENINGSTEMPERATUR
Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C.
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national
lovgivning for elektriske installationer.
EISEN: Dit product voldoet aan de volgende eisen.
RFI Emissie
EN55022 Klasse B
WAARSCHUWING: Dit product vereist beschermende kabels in overeenstemming met de
limieten van Klasse B emissie. Als het niet met beschermende kabels wordt gebruikt, kan
dit produkt radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om
gepaste maatregelen te nemen.
Immuniteit
EN50082-1
Electrische Veiligheid
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
VEILIGHEID
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT WAARSCHUWING: GEVAAR
VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin
bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen worden. Dit
toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door een
daartoe opgeleide en bevoegde technicus. Om het gevaar op ELEKTRISCHE SCHOKKEN te
vermijden, moet u het toestel van de stroombron ontkoppelen alvorens de LAN-kabels te
koppelen of ontkoppelen.
Dit is een “KLASSE 1 LED-PRODUKT”
GEVAAR VOOR BLIKSEMINSLAG GEVAAR: NIET aan toestellen of KABELS WERKEN bij
BLIKSEM.
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE STROOMKABEL TE
ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE MAKEN: de stroomkabel ontkoppelen.
INSTALLATIE
ELEKTRISCH: AUTOMATISCHE AANPASSING VAN DE SPANNING
Dit toestel past zich automatisch aan elke spanning aan, tussen de op het label vermelde
waarden.
ELEKTRISCHE TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een juist
geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen onderdelen waarmee
de gebruiker eventueel in aanraking komt onder gevaarlijke spanning stellen.
ELEKTRISCHE SNOEREN
Gebruik een elektrisch snoer, maximum 4,5 meter lang, berekend voor ten minste 6
ampåçère, 250 V, uit HAR vervaardigd, met aan het ene uiteinde een gevormd IEC 320
aansluitstuk en aan het andere uiteinde een stekker die goedgekeurd is door het land waar
het toestel gebruikt zal worden.
19
Electrical Safety and Installation Requirements
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht
ongehinderd toelaten voor afkoeling.
BEDRIJFSTEMPERATUUR
De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius.
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale elektrische
voorschriften.
NORMES: ce produit est conforme aux normes de suivantes :
Emission d’interférences radioélectriques
EN55022 Classe B
MISE EN GARDE: conformément aux limites d’émission de la Classe B, ce produit doit être
utilisé avec des câbles blindés. Si ce produit n’est pas utilisé avec des câbles blindés, il peut
émettre des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les
mesures adéquates.
Immunité
EN50082 - 1
Sécurité électrique
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SÉCURITÉ
INFORMATION SUR LES RISQUES ÉLECTRIQUES AVERTISSEMEN :
DANGER D’ÉLECTROCUTION Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement
protecteur du matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un technicien
dûment qualifié. Pour éviter tout risque d’ÉLECTROCUTION, débrancher le matériel avant de
connecter ou de déconnecter les câbles LAN.
Ce matériel est un “PRODUIT À DIODE ÉLECTROLUMINESCENTE DE CLASSE 1”
DANGER DE FOUDRE DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité
orageuse.
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT. POUR COUPER
L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.
INSTALLATION
RÉGLAGE DE TENSION AUTOMATIQUE ÉLECTRIQUE
Ce matériel peut s’ajuster automatiquement sur n’importe quelle tension comprise dans la plage
indiquée sur l’étiquette.
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La
prise de courant doit être branchée dans une prise femelle correctement mise à la terre car
des tensions dangereuses risqueraient d’atteindre les pièces métalliques accessibles à
l’utilisateur.
INFORMATION SUR LE CORDON ÉLECTRIQUE
Utiliser un cordon secteur de 4.5 mètres de long maximum, calibré à 5 ampères minimum, 250V,
fabriqué en câblage <HAR> avec connecteur IEC 32C moulé à une extrémité, et à l’autre extrémité,
une prise de courant mâle répondant aux normes du pays d’utilisation.
20
AT-FS709FC Installation Guide
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de circuler
librement pour le refroidissement.
TEMPÉRATURE DE FONCTIONNEMENT
Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques nationales et
locales.
STANDARDI : Tämä tuote on seuraavien standardien mukainen.
Radioaaltojen häirintä
EN55022 Luokka B
VAROITUS: Tämä tuote vaatii suojatut kaabelit täyttääkseen B Luokan säteilyrajoitukset. Ellei
suojattuja kaapeleita käytetä, tämä laite voi aiheuttaa radioaaltohäriöitä, missä tapauksessa
laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin.
Kestävyys
EN50082-1
Sähköturvallisuus
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
TURVALLISUUS
SÄHKÖÖN LIITTYVIÄ HUOMAUTUK SIAVAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia.
Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä
teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden katkaise sähkövirta tuotteeseen ennen
kuin liität tai irrotat paikallisverkon (LAN) kaapelit.
Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE”
SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA SALAMOINNIN
AIKANA.
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA. VIRTA
KATKAISTAAN irrottamalla virtajohto.
ASENNUS
SÄHKÖ - AUTOMAATTINEN JÄNNITTEENSÄÄTÖ
Tämä tuote säätää automaattisesti mihin tahansa jännitteeseen ohjetarrassa annettujen
arvojen välillä.
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti maadoitettuun
pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa metalliosat vaarallisille
jännitteille.
SÄHKÖ - JOHTOON LIITTYVÄ HUOMAUTUS
Käytä seuraavanlaista virtajohtoa: maksimipituus 4,5 metriä, minimiteho 5 ampeeria, 250 V,
valmistettu <HAR> -johdostosta, muovattu IEC 320 -liitin toisessa päässä ja käyttömaassa
hyväksytty pistoke toisessa päässä.
21
Electrical Safety and Installation Requirements
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys ympäröivään
huoneilmaan, jotta ilmanvaihto tapahtuisi.
KÄYTTÖLÄMPÖTILA
Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C.
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten
mukaisesti.
STANDARD: Questo prodotto è conforme ai seguenti standard.
Emissione RFI (interferenza di radiofrequenza)
EN55022 Classe B
AVVERTENZA: questo prodotto richiede cavi schermati per adeguarsi ai limiti di emissione
per gli apparecchi di Classe B. Se non viene usato con cavi schermati, questo prodotto
potrebbe causare radio interferenza, nel qual caso potrebbe richiedersi all’utente di prendere
gli adeguati provvedimenti.
Immunità
EN50082-1
Sicurezza elettrica
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
NORME DI SICUREZZA
AVVERTENZE ELETTRICHE ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE Per evitare
SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne non sono riparabili
dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta solamente da un tecnico
specializzato e qualificato. Per evitare ogni possibilità di SCOSSE ELETTRICHE,
interrompere l’alimentazione del dispositivo prima di collegare o staccare i cavi LAN.
Questo è un “PRODOTTO CON LED DI CLASSE 1”
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO DI
DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL DISPOSITIVO staccare il cavo di
alimentazione.
INSTALLAZIONE
ELETTRICITÀ - REGOLAZIONE AUTOMATICA DELLA TENSIONE
Questo prodotto regolerà automaticamente la tensione ad un valore compreso nella gamma
indicata sull’etichetta.
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere inserita in
una presa di corrente specificamente dotata di messa a terra. Una presa non cablata in
maniera corretta rischia di scaricare una tensione pericolosa su parti metalliche accessibili.
ELETTRICITÀ - AVVERTENZA SUL CAVO
Usare un cavo della lunghezza massima di metri 4,5, con capacità minima di 5 A, 250 V, di
filo <HAR>, dotato di connettore stampato IEC 320 ad un’estremità e di spina approvata dal
paese di destinazione all’altra.
22
AT-FS709FC Installation Guide
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero ricircolo
dell’aria ambiente per il raffreddamento.
TEMPERATURA DI FUNZIONAMENTO
Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche
nazionali.
SIKKERHETSNORMER: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
RFI stråling
EN55022 Klasse B
ADVARSEL: Det må benyttes isolerte kabler med dette produktet for å tilfredsstille Klasse B
strålingsgrenser. Hvis ikke kan dette produktet forårsake radioforstyrrelse. Hvis dette skjer,
må brukeren ta de nødvendige forholdsregler.
Immunitet
EN50082-1
Elektrisk sikkerhet
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SIKKERHE
ELEKTRISITETADVARSEL: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som brukeren
kan reparere på innsiden. Denne enheten inneholder FARLIGE SPENNINGER, og må kun
åpnes av en faglig kvalifisert tekniker. For å unngå ELEKTRISK SJOKK må den elektriske
strømmen til produktet være avslått før LAN-kablene til- eller frakobles.
Dette er et “KLASSE 1 LED PRODUKT”
FARE FOR LYNNEDSLAG FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR Å
DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.
INSTALLASJON
ELEKTRISK - AUTO SPENNINGSTILPASNING
Dette produktet vil automatisk bli tilpasset hvilken som helst strømspenning i de områdene
som vises på etiketten.
ELEKTRISK - TYPE 1- KLASSE UTSTYR
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt jordet
kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i lett t
ilgjengelige metalldeler.
ELEKTRISK - MEDDELELSE OM LEDNINGER
Bruk en strømledning av maksimalt 4.5 m. i lengde, godkjent for minst av 5 amp, 250V,
fremstilt av <HAR> ledning IEC 320 koplingsstykke i den ene enden, og i den andre enden en
plugg som er blitt godkjent i brukerlandet.
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med
romtemperatur for avkjøling.
23
Electrical Safety and Installation Requirements
DRIFTSTEMPERATUR
Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius.
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske
koder.
PADRÕES: Este produto atende aos seguintes padrões.
Emissão de interferência de radiofrequência
EN55022 Classe B
AVISO: Este produto requer cabos protegidos a fim de obedecer aos limites de emissão da
Classe B. Se não for utilizado com os cabos protegidos, este produto pode causar
interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as
medidas adequadas.
Imunidade
EN50082-1
Segurança Eléctrica
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SEGURANÇA
AVISOS SOBRE CARACTERÍSTICAS ELÉ T R I C A
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO Para evitar CHOQUE ELÉTRICO, não retire a
tampa. Não contém peças que possam ser consertadas pelo usuário. Este aparelho contém
VOLTAGENS PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado. Para
evitar a possibilidade de CHOQUE ELÉTRICO, desconecte o aparelho da fonte de energia
elétrica antes de conectar e desconectar os cabos da LAN.
Este é um “PRODUTO CLASSE 1 LED”
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos suscetíveis a
QUEDAS DE RAIO.
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO DE
DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO, desconecte o cabo de
ALIMENTAÇÃO.
INSTALAÇÃO
ELÉTRICO - AJUSTE AUTOMÁTICO DE VOLTAGEM
Este produto ajustar-se-á automaticamente a qualquer voltagem que esteja dentro dos
limites indicados no rótulo.
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue de
alimentação deve ser conectado a uma tomada com adequada ligação de fio terra. Tomadas
sem adequada ligação de fio terra podem transmitir voltagens perigosas a peças metálicas
expostas.
ELÉTRICO - AVISO SOBRE O CABO DE ALIMENTAÇÃO
Use cabo de alimentação com comprimento máximo de 4,5metros, com uma capacidade indicada
mínima de 5 amp e 250 V, fabricado de material para cabo <HAR> com conector moldado
IEC 320 em uma extremidade e, na outra extremidade, um plugue aprovado para uso no
país em questão.
24
AT-FS709FC Installation Guide
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso livre
ao ar ambiente para arrefecimento adequado do aparelho.
TEMPERATURA DE FUNCIONAMENTO
Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais para
instalações elétricas.
ESTÁNDARES: Este producto cumple con los siguientes estándares.
Emisión RFI
EN55022 Clase B
ADVERTENCIA: este producto requiere de cables armados para cumplir con los límites de
emisión de Clase B. Si no se usa con cables armados, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que
sean convenientes al respecto.
Inmunidad
EN50082-1
Seguridad eléctrica
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SEGURIDAD
AVISOS ELECTRICOS ADVERTENCIA: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior
al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES PELIGROSOS y
sólo deberá abrirla un técnico entrenado y calificado. Para evitar la posibilidad de
ELECTROCHOQUE desconecte la corriente eléctrica que llega al producto antes de conecta
o desconectar los cables LAN.
Este es un “PRODUCTO DE DIODO LUMINISCENTE (LED) CLASE 1”
PELIGRO DE RAYOS PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en
los equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN DISPOSITIVO DE
DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte el cable de alimentación.
INSTALACION
ELECTRICO - AUTO-AJUSTE DE TENSION
Este producto se ajustará automáticamente a cualquier tensión entre los valores máximos y
mínimos indicados en la etiqueta.
ELECTRICO - EQUIPO DEL TIPO CLASE 1
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que conectarse a un
enchufe a tierra debidamente instalado. Un enchufe que no está correctamente instalado
podría ocasionar tensiones peligrosas en las partes metálicas que están expuestas.
ELECTRICO - ADVERTENCIA SOBRE EL CABLE
Use un cable eléctrico con un máximo de 4,5 metros de largo, con una capacidad mínima de
5 amperios, 250 V, hecho de cable <HAR>, con el conector moldeado IEC 320 en un
extremo y con un enchufe que está aprobado por el país de uso final en el otro.
25
Electrical Safety and Installation Requirements
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener acceso
libre al aire ambiental de la sala para su enfriamiento.
TEMPERATURA REQUERIDA PARA LA OPERACIÓN
Este producto está diseñado para una temperatura ambiental máxima de 40 grados C.
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos Eléctricos
locales y nacionales.
STANDARDER: Denna produkt uppfyller följande standarder.
Radiostörning
EN55022 Klass B
VARNING: Skärmkabel bör användas med denna produkt för att uppfylla kraven gällande
radiostörningar enligt Klass B. Om ingen skärmkabel används med denna produkt, kan
radiostörningar uppstå, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder.
Immunitet
EN50082-1
Elsäkerhet
TUV-EN60950, UL1950, CSA 950
Laser
EN60825
SÄKERHET
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK: RISK FÖR ELEKTRISK
STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det finns inga delar inuti som behöve
underhållas. Denna apparat är under HÖGSPÄNNING och får endast öppnas av en utbildad
kvalificerad tekniker. För att undvika ELEKTRISK STÖT, koppla ifrån produktens
strömanslutning innan LAN-kablarna ansluts eller kopplas ur.
Detta är en “KLASS 1 LYSDIODPRODUKT”
FARA FÖR BLIXTNEDSLAG FARA: ARBETA EJ på utrustningen eller kablarna vid
ÅSKVÄDER.
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN
STRÖMMEN, dra ur nätkabeln.
INSTALLATION
ELEKTRISKT - AUTOMATISK SPÄNNINGSJUSTERING
Denna produkt justeras automatiskt till alla spänningar inom omfånget som indikeras på
produktens märkning.
ELEKTRISKT - TYP KLASS 1 UTRUSTNING
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten till ett
ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar utsätts fö
högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk.
ELEKTRISKT - ANMÄRKNING BETRÄFFANDE KABELN
Använd en kabel med maximum längd 4,5 meter och minimum 5 amp nominal, 250V,av <HAR>
kabelfabrikat med ett specialutformat IEC 320-kontaktdon i ena änden och i den andra en
plugg som godkänts i landet där produkten används.
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande rumsluft
för avsvalning.
26
AT-FS709FC Installation Guide
DRIFTSTEMPERATUR
Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader Celsius.
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser för
elektrisk utrustning.
27
Appendix B
Switch Specifications
Physical Characteristics
Chassis dimensions:
LxWxH
13 in x 8.0 in x 1.72 in
330 mm x 203 mm x 44 mm
Weight:
4 lbs (2.0 kg)
Operating temperatures:
0° to 40° C (32° to 104° F)
Storage temperatures:
-20° to 60° C (-40° to 158° F)
Relative humidity:
10% to 80% (operating)
5% to 95% (storage)
Operating altitude:
Up to 10,000 ft (3,048 m)
Safety Agency
CE compliant
Standard:
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u, 100Base-TX Fast Ethernet,
IEEE 802.3x, 100Base-FX Fast Ethernet
EMI/RFI:
Complies with FCC Class B,
EN55022 Class B
Safety:
Complies with safety standards UL 1950, 3rd
Edition, EN60950 and EN60825
Safety approval marks:
UL, CUL
Immunity:
Complies with EN50082-1 Immunity Standard
29
Switch Specifications
Cable Specifications
Table 4 IEEE 802.3 and 802.3u Network Specifications
10Base-T
100Base-TX
Media
Shielded Twisted Pair
Category 3 or 5
Shielded Twisted Pair
Category 5 only
Topology
Star, Tree
Star, Tree
External Devices
Network Adapter Card,
Repeater, Switch
Network Adapter Card,
Repeater, Switch
Maximum Segment Length
328 ft (100 m)
328 ft (100 m)
Table 5
100Base-FC
Media
SC Fiber Optic Cable
50/100 µm, or 62.5/25 µm
Topology
Star, Tree
External Devices
Network Adapter Card, Switch
Maximum Segment Length
1.25 mi (2 Km)
30
Appendix C
Technical Support Fax Order
Name ___________________________________________________________________
Company ________________________________________________________________
Address _________________________________________________________________
City ________________________State/Province ________________________________
Zip/Postal Code ___________________ Country_________________________________
Phone _______________________________Fax_________________________________
Incident Summary
Model number of Allied Telesyn product I am using ______________________________
Network software products I am using _________________________________________
_______________________________________________________________________
Brief summary of problem __________________________________________________
_______________________________________________________________________
Conditions (List the steps that led up to the problem.) ____________________________
_______________________________________________________________________
_______________________________________ _______________________________
Detailed description (Use separate sheet, if necessary)___________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
When completed, fax this sheet to the appropriate Allied Telesyn office. Fax numbers can
be found on page35.
31
Appendix D
AT-FS709FC Installation Feedback
Please tell us what additional information you would like to see discussed in the guide. If
there are topics you would like information on that were not covered in the guide, please
photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn.
The mailing address and fax number are at the bottom of the page. Your comments are
valuable when we plan future revisions of the guide.
I found the following the most valuable _______________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
I would like the following more develop e ____________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
I would find the guide more useful i _________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Please fax or mail your feedback. Fax to 1-408-736-0100. Or mail to:
Allied Telesyn International, Corp.
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
PN 613-10817-00 Rev. A
33
Appendix E
Where To Find Us
For Technical Support or Service
Location
Phone
Fax
Americas
United States, Canada, Mexico, Central
America, South America
1 (800) 428-4835
1 (918) 628-3222
Asia
Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China, India
(+65) 3815-613
(+65) 3833-830
Australia
Australia, New Zealand
(+61) 2-943-5111
(+61) 2-9438-4966
France
France, Belgium, Luxembourg, The
Netherlands, Middle East, Africa
(+33) 1-60-92-15-32
(+33) 1-69-28-37-49
Germany
Germany, Switzerland, Austria, Eastern
Europe
(+49) 30-435-900-126
(+49) 30-435-70-650
Hong Kong
(+852) 2-529-4111
(+852) 2 529-7661
Italy
Italy, Spain, Portugal, Greece, Turkey, Israel
(+39) 02-416047
(+39) 02-419282
Japan
(+81) 3-3443-5640
(+81) 3-3443-2443
United Kingdom
United Kingdom, Denmark, Norway, Sweden,
Finland, Iceland
(+44) 1-235-442560
(+44) 1-235-442680
Technical Bulletin Board Service
1 (425) 483-7979
Technical Support E-mail Address
[email protected]
CompuServe
Go ALLIED
FTP Server
Address: ftp.alliedtelesyn.com [lowercase letters]
Login: anonymous [lowercase letters]
Password: your e-mail address [requested by the server at login]
For Sales or Corporate Information
AlliedTelesyn International, Corp.
19015 North Creek Parkway
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: 1 (800) 424-4284 (USA and Canada)
Fax: 1 (408) 736-0100
World Wide Web:
http://www.alliedtelesyn.com
35