advertisement
Mini Hidden Pinhole Camera
User’s Guide
CM-S10055BK
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
SAFETY PRECAUTIONS
WARNING CAUTION
1. Be sure to use only the standard adapter that is
specified in the specification sheet. Using any
other adapter could cause fire, electrical shock, or
damage to the product
2. Incorrectly connecting the power supply or
replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single
adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power
receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and
firmly. A falling camera may cause personal injury
6. Do not place conductive objects (e.g.screwdrivers,
coins, metal things, etc.) or containers filled with
water on top of the camera. Doing so may cause
personal injury due to fire, electric shock, or falling
objects.
7. Do not install the unit in humid, dusty, or sooty
locations. Doing so may cause fire or electric
shock.
8. If any unusual smells or smoke come from the unit,
stop using the product. In such case, immediately
disconnect the power source and contact the
service center. Continued use in such a condition
may cause fire or electric shock.
9. If this product fails to operate normally, contact the
nearest service center. Never attempt to modify
this product in any way. (ZMODO is not liable for
problems caused by unauthorized modifications or
attempted repair.)
10. When cleaning, do not spray water directly onto
parts of the product. Doing so may cause fire or
electric shock.
1. Do not drop objects on the product or apply strong
shock to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high
temperature (over 120F), low temperature (below
-5F), or high humidity. Doing so may cause fire or
electric shock.
3. If you want to relocate the already installed
product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then
there is a lightning. Neglecting to do so may cause
fire or damage to the product.
5. Keep out of direct sunlight and heat radiation
sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards
extremely bright objects such as sun, as this may
damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and
shall stay readily operable at any time.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.
1
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
PRODUCT OVERVIEW
Product Overview
Discretely monitor your home or small business with this hidden camera. Featuring a clever styling as an easily overlooked common item, this camera includes imaging provided by a 1/3"
Sony Color CCD, which delivers good video quality, reliable operation, a long operating life, and high value. This hidden camera is designed for indoor use, and can easily be mounted for the perfect viewing angle. BNC and RCA connections are used for video and power. Installation is easy and hassle free, just plug and play.
Package includes
Please check your camera and accessories included in the package. Those components are as shown below:
Camera
Main Features
1/3" Sony Color CCD Image Sensor
420 TV Lines, Horizontal
3.7mm Pinhole Lens
Signal: NTSC
Iris: Auto
Night Vision Min. Light: 0.5 Lux (F1.2)
Operation Temperature: -5F ~ 120F
Mount: Wall or Ceiling
Video Connector: BNC
Power Connector: RCA 12V DC
Screws
Mount Bracket
CCD CAMERA
CCD CAM
ERA
WWW.Z
MODO
.COM
C
C
D
C
AM
ER
A
W
W
W
.Z
M
OD
O.
CO
M
Package Box
1) CM-S10055BK Mini Hidden Pinhole Camera
1) A Card
3) Screws
1) Package Box
2
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
SCHEMATIC DIAGRAM
1 Main Body
2 Pinhole Lens
3 Mount Bracket
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
3
CONNECTING CABLES
RCA Cable
DVR
Video Balun
Monitor
BNC Cable
To connect cables
1.
Connect the BNC cable to the video connector attached on your camera
2.
Connect the BNC cable to the Video Input on a monitor, DVR or Video Balun.
3. Connect the power adapter to the RCA Power connector attached on your camera. When the
monitor is turned on, the camera image appears.
Note
It is very important that you identify these ends before installing the cable so that you have the correct ends at the correct location.
4
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
HOW TO INSTALL
Before installation
Please read the following instructions before installing your camera:
You have to check whether the location (ceiling or wall) can bear five times the weight of your
camera.
Do not allow the cable to be caught in a pinched area, otherwise the electric line cover may be
damaged. This may cause cable breakdown or fire.
When installing your camera, don't allow anyone to walk or stand under your installation site,
and remove all valuable items. A dropped camera may cause injury to bystanders or harm to
valuable items.
Installation procedure
To install your camera step
5
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
HOW TO INSTALL
Pinhole Lens step
Attach the Mount Bracket to the 2 screws supplied in your package. As shown in the picture, push the three screws into the 3 holes on the bottom of the Mount Bracket, then twist in the screws into the wall using a screwdriver.
step on clockwise until it becomes tight.
Note
As shown on the left, you can also put the whole Main Body into the wall or ceiling.
Only left the pinhole lens outside. If mounted in this way, it will be more covert.
step
Bracket. Make sure that the pinhole lens is facing the camera’s monitoring area.
The camera now is installed on the mounting location.
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
6
Screw
CAMERA SPECIFICATION
Specifications for NTSC & PAL Standard
Item
Product type
Power input
Broadcast type
Power Consumption
Image device
Effective Pixels
Scanning mode
Synchronization mode
Horizontal resolution
Minimum illumination
Signal output
Lens
S/N Ratio
Controls
Product color
Operation temperature
Size (package)
Weight
Mounting
Details
Mini Pinhole Hidden Camera
NTSC Standard color system
DC 12V
PAL Standard color system
(525 Lines, 60 Fields) (625 Lines, 50 Fields)
Approx. 120mA
1/3 inch SONY Color CCD
510(H) x 492(V), 250,920 pixels
NTSC Standard PAL Standard
525 Lines 625 Lines
Internal Synchronization
Focal Length
420 TV Lines
0.5Lux (F1.2)
1.0Vp-p, 75ohms
Zone
Horizontal
Limit of Viewing Angle
3.7mm pinhole
Vertical
78°
68°
> 48dB
Auto Iris
Auto Gain Control
Auto Back Light Compensation
Auto Switching between Color and B&W by day and night change(D/N)
Black
-5F—120F
2.44"x 1.69"x 1.81”
0.31 lbs
Ceiling or Wall
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
7
FCC Statement
This device complies with part 15of the FCC
Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 1 5 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Correct Disposal of This Product
(Waste Electrical & Electronic
Equipment) (Applicable in the
European Union and other
European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it shouldnot be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
SKU: CM-S10055BK
8 4 6 6 5 5 0 0 1 5 6 2
8
1201-1205 ,Sangda Mansion, High Technology Park,
ShenZhen, Guangdong, China
Tel: 0755-3363-1636 Fax: 0755-3363-1639
advertisement
Related manuals
advertisement