TNC
CONTENTS
PAGE
TNC SERIES
General .................................................................................................................... 4
Interface.................................................................................................................... 5
Characteristics.......................................................................................................6-7
TNC 50 Ω SERIES
Plugs......................................................................................................................8-9
Jacks .................................................................................................................10-11
Jacks and receptacles ............................................................................................ 12
Receptacles.......................................................................................................13-14
Adapters ................................................................................................................. 15
Caps ....................................................................................................................... 16
TNC 75 Ω SERIES
Plugs....................................................................................................................... 17
Jacks and adapters ................................................................................................ 18
TNC 18 GHz SERIES
Characteristics........................................................................................................ 19
Plugs and jacks ...................................................................................................... 20
Jacks ...................................................................................................................... 21
Receptacles............................................................................................................ 22
Adapters and cap ................................................................................................... 23
Panel drilling ........................................................................................................... 24
Assembly instructions........................................................................................25-38
11-3
TNC
GENERAL
50 Ω
75 Ω
50 and 75 Ω
DC - 11 GHz standard
DC - 18 GHz 18 GHz series
DC - 1.5 GHz
DC - 1 GHz recommended
DC - 1.5 GHz commercial
GENERAL
•
•
•
•
•
Screw-on equivalent to BNC bayonet series
Good RF performance
Suitable for high power levels
Long life and high strength
3 ranges:
-
Standard TNC series (50 and 75 Ω fully intermatable)
-
Commercial TNC series (50 and 75 Ω)
-
18 GHz TNC series (50 Ω)
APPLICABLE STANDARDS
•
•
•
MIL-C-39012 / MIL STD 348A/313
IEC 60169-17
CECC 22200
APPLICATIONS
•
•
•
•
Avionics
Aeronautics
Countermeasures
Telecommunications
11-4
TNC
INTERFACE
PLUG
LETTER
JACK
mm
inch
min.
max.
min.
max.
LETTER
mm
inch
min.
max.
min.
max.
A
1.32
1.37
0.052
0.054
A
-
4.72
-
0.186
B
4.83
-
0.190
-
B
8.1
8.1
0.319
0.321
D
11.40
-
0.449
-
C
8.31
8.46
0.327
0.333
E
-
2.2
-
0.087
D
8.79
9.04
0.346
0.356
F
0.35
0.65
0.014
0.025
E
9.6
9.68
0.378
0.381
G
7
7.05
0.275
0.277
F
-
2.2
-
0.087
1
4.9
5.7
0.193
0.224
H
-
5.9
-
0.232
2
5.28
5.79
0.208
0.228
1
8.3
8.5
0.327
0.335
3
0.15
-
0.006
-
2
1.73
2.24
0.068
0.088
4
1.8
-
0.071
-
3
4.75
-
0.187
-
5
0.15
-
0.006
-
4
-
0.15
-
0.006
6
0.08
1.02
0.003
0.040
5
4.72
5.23
0.186
0.206
7
5.33
5.84
0.210
0.230
6
4.78
5.28
0.188
0.208
8
0.7
1.98
0.027
0.078
7
10.7
-
0.421
-
8
0.38
0.76
0.015
0.030
9
4.95
-
0.195
-
11-5
TNC
CHARACTERISTICS
STANDARD TNC
TEST/CHARACTERISTICS
MIL-C-39012 A
VALUES/REMARKS
ELECTRICAL CHARACTERISTICS
Impedance
50 Ω
75 Ω
Frequency range
DC - 11 GHz
DC - 1.5 GHz
V.S.W.R.
3-14
1.30 max
Insertion loss
3-27
0.18 dB max at 9 GHz
RF leakage
3-26
-60 dB min from 2 to 3 GHz
Insulation resistance
3-11
5000 MΩ min
Contact resistance
3-16
Initial
1.5
0.2
center contact (mΩ)
outer contact (mΩ)
Working voltage
After proof
2
-
At sea level: 500 V rms
at 70000 ft (21000 m): 125 V rms
Dielectric withstanding voltage
3-17
At sea level: 1500 V rms
at 70000 ft (21000 m): 375 V rms
RF withstanding voltage
3-23
At sea level: 1000 V rms (5 MHz sine wave)
MECHANICAL CHARACTERISTICS
Durability
3-15
500 matings
Mating / unmating
axial force: not applicable
torque: 1.96 inch pounds (22.6 N.cm)
Recommended mating torque
3.99 to 5.98 inch pounds (46 to 69 N.cm)
Proof torque
14.74 inch pounds (170 N.cm)
Coupling mechanism retention force
3-25
Cabling retention force
3-24
100 Lbf (44.5 daN)
cable clamp:
crimped:
40.6 Lbf (181 N min) (all cables)
51 Lbf (227 N min) (cable dia. .189 (4.8) to .228 (5.8))
76.4 Lbf (340 N min) (cable dia. .250 (6.35) and above)
Center contact retention
Axial: 6.06 Lbf (27 N)
ENVIRONMENTAL CHARACTERISTICS
Temperature range
standard models
hermetic sealed models
models for semi-rigid cables
Thermal shock
-65°C / + 165°C
-65°C / +100°C
-65°C / +105°C
3-20
High temperature endurance
MIL-STD-202, method 107, condition B
MIL-STD-202, method 108
Corrosion (salt spray)
3-13
Vibrations
3-18
MIL-STD-202, method 101, condition B
MIL-STD-202, method 204, condition B
Shocks
3-19
MIL-STD-202, method 213, condition G
Moisture resistance
3-21
MIL-STD-202, method 106
Low pressure
3-22
Not applicable
Hermetic seal
Applied vacuum 10-6 mm of Hg (Torrs)
leakage rate < 10-6 atm/cm3/s
Leakage
Pressure 3.5 bars; duration 2 mn; temperature 15°C to 25°C
MATERIALS
Body and center pin contact
Center socket contact
Ferrules
Insulators
Gaskets
Brass as per QQ-B-626
Beryllium copper as per QQ-C-530
Brass
PTFE teflon
Silicone elastomer
PLATING
Body
Center contacts
Nickel plated
Gold plated
All dimensions are given in mm
11-6
TNC
CHARACTERISTICS
COMMERCIAL TNC
TEST/CHARACTERISTICS
VALUES/REMARKS
ELECTRICAL CHARACTERISTICS
50 Ω
Impedance
Frequency range
75 Ω
DC - 1.5 GHz
Test voltage
1500 V rms
Operating voltage
500 V rms
Insulation resistance
5000 mΩ min (500 V)
Contact resistance
10 mΩ max
ENVIRONMENTAL CHARACTERISTICS
Temperature range
–35°C / + 70°C
PLATING
Body
Nickel
Center contacts
Gold
11-7
TNC 50 Ω
PLUGS
STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLE
Fig. 1
Cable group
2.6 / 50 S
Part number
R143 075 000
R143 075 161
Fig. 2
Dimensions (mm)
Fig
1
A
B
C
D
0.6
1.75
3.25
29.6
Captive center
contact
5 / 50 S
R143 082 161
yes
5 / 50 D
R143 073 000
R143 074 000
Packaging
commercial version
M 02
1.05
3
0.75
3.1
5.55
3.075
5.5
3.9
6.6
Note
100 pieces
2
R143 072 000
6 / 75 + 93
Assembly
instructions
M 03
R143 082 000
5 / 50 S
Fig. 3
no
full crimp
commercial version, full
crimp
M 05
M 10
yes
unit
M 05
STRAIGHT PLUGS CLAMP TYPE FOR FLEXIBLE CABLE
Fig. 1
Cable group
Part number
2.6 / 50 + 75
R143 004 000
5 / 50 S + D
R143 008 000
6 / 75 + 93
R143 012 000
10 + 11 / 50
R143 018 000
Fig.
1
2
Fig. 2
Dimensions (mm)
A
B
C
Captive center contact
Assembly
instructions
Packaging
26.5
0.6
3.1
yes
M 06
Unit
27.1
1.2
5.6
no
M 07
100 pieces
27
1.05
6.65
yes
M 07
M 07
Unit
Note
conical
braid clamp
11-8
TNC 50 Ω
PLUGS
STRAIGHT PLUG CLAMP TYPE FOR SEMI RIGID CABLE
Cable group
Part number
Captive center contact
Assembly
instructions
Packaging
.141”
R143 052 000
no
M 08
Unit
RIGHT ANGLE PLUGS CRIMP TYPE FOR FLEXIBLE CABLE
Fig. 1
Cable group
Part number
Fig.
2.6 / 50 S
R143 181 161
1
R143 182 161
2
R143 182 000
3
5 / 50 S
Fig. 2
Captive center contact
Fig. 3
Assembly instructions
M 04
yes
M 04
M 01
Packaging
Note
100 pieces
commercial
version
unit
RIGHT ANGLE PLUG CLAMP TYPE FOR FLEXIBLE CABLE
Cable group
Part number
Captive center contact
Assembly
instructions
Packaging
5 / 50 S + D
R143 156 000
yes
M 07
Unit
11-9
TNC 50 Ω
JACKS
STRAIGHT JACKS CRIMP TYPE FOR FLEXIBLE CABLE
Fig. 1
Fig. 2
Cable group
Part number
Fig
Captive center contact
Assembly
instructions
Packaging
2.6 / 50 S + D
R143 237 000
1
yes
M03
Unit
5 / 50 S
R143 235 161
2
yes
M02
100 pieces
Note
commercial version,
full crimp
STRAIGHT BULKHEAD JACKS CRIMP TYPE FOR FLEXIBLE CABLE (REAR MOUNT)
Cable group
Part number
2.6 / 50 S
5 / 50 S
Dimensions (mm)
A
B
C
D
R143 331 161
38
0.6
1.75
3.10
R143 332 161
35
1.05
3.10
5.55
Captive center
contact
Assembly
instructions
Panel
drilling
Packaging
commercial version,
panel sealed
M03
yes
P09+P11
M02
Note
100 pieces
commercial version,
panel sealed, full
crimp
11-10
TNC 50 Ω
JACKS
STRAIGHT JACK CLAMP TYPE FOR FLEXIBLE CABLE
Cable group
Part number
Captive center contact
Assembly instructions
Packaging
5 / 50 S
R143 207 000
no
M07
Unit
STRAIGHT SQUARE FLANGE JACKS CLAMP TYPE FOR FLEXIBLE CABLE
Dimensions (mm)
Cable group
Part number
2.6 / 50 + 75
R143 254 000
29.8
0.6
5 / 50 S + D
R143 258 000
30.2
1.05
A
B
Captive center contact
Assembly
instructions
3.1
yes
M06
5.6
no
M07
C
Panel drilling
Packaging
P04
Unit
Also for screws type 3-56 UNF 2A
17.5 mm SQUARE FLANGE STRAIGHT JACK SOLDER TYPE FOR SEMI RIGID CABLE
Cable group
Part number
Captive center contact
Assembly
instructions
Panel drilling
Packaging
.085’’
R143 257 440
no
M12
P01
Unit
11-11
TNC 50 Ω
JACKS & RECEPTACLES
STRAIGHT BULKHEAD JACKS PANEL SEALED REAR MOUNT
Dimensions (mm)
Cable group
Part number
2.6 / 50
R143 324 000
29.6
3.1
5 / 50 S
R143 325 000
30.17
5.6
A
B
Assembly
Panel drilling
instructions
Captive center contact
M11
yes
M07
Packaging
100 pieces
P09
Unit
17.5 mm SQUARE FLANGE STRAIGHT FEMALE RECEPTACLES
Part number
Dimension A (mm)
R143 404 000
M2.5 x 0.45
R143 405 000
2.6
Captive center contact
yes
Panel drilling
P05
Packaging
unit
100 pieces
Note
Solder pot
11-12
TNC 50 Ω
RECEPTACLES
19 mm SQUARE FLANGE STRAIGHT FEMALE RECEPTACLE
Part number
Captive center contact
Panel drilling
Packaging
Note
R143 420 000
no
P02
Unit
Slotted contact
2 HOLES FLANGE STRAIGHT FEMALE RECEPTACLE
Part number
Captive center contact
Panel drilling
Packaging
Note
R143 453 000
yes
P07
Unit
Solder pot contact
BULKHEAD STRAIGHT FEMALE RECEPTACLES
Fig. 1
Part number
Fig
R143 557 000
1
R143 603 000
2
Captive center contact
Fig. 2
Panel drilling
Packaging
P08
yes
P10
Note
Front mount, solder pot contact
Unit
Panel sealed, front mount, solder
pot contact
11-13
TNC 50 Ω
RECEPTACLES
17.5 mm SQUARE FLANGE RIGHT ANGLE FEMALE RECEPTACLE
Part number
Captive center contact
Panel drilling
Packaging
Note
R143 654 000
yes
P06
Unit
Solder pot contact
RIGHT ANGLE BULKHEAD FEMALE RECEPTACLE
Part number
R143 680 000
Captive center contact
yes
Panel drilling
Packaging
Note
Unit
Panel sealed, front mount,
solder pot contact
P08
17.5 mm SQUARE FLANGE STRAIGHT MALE RECEPTACLE
Part number
Captive center contact
Panel drilling
Packaging
Note
R143 440 000
yes
P03
Unit
Solder pot contact
11-14
TNC 50 Ω
IN SERIES ADAPTERS
IN SERIES ADAPTERS
Fig. 1
Fig. 2
Fig. 4
Fig. 5
Fig. 7
Part number
Fig. 3
Fig. 6
Fig. 8
Captive center contact
Fig
Fig. 9
Panel drilling
Packaging
Note
R143 703 000
1
R143 704 000
2
Female-female
3
Square flange femalefemale
R143 710 000
Male-male
Unit
P01
R143 713 000
R143 753 000
yes
4
Square flange slide on type
male-female
5
Bulkhead hermetic, panel
sealed female-female
P09
100 pieces
R143 720 161
6
Commercial version,
bulkhead female-female
R143 770 000
7
Right angle male-female
R143 780 000
8
R143 782 000
9
unit
Female female male
Female female female
11-15
TNC 50 Ω
CAPS
PROTECTIVE CAPS
Fig. 1
Part number
Fig.
Finish
Black chromium
R143 805 000
1
R143 812 000
2
R143 835 000
3
Nickel
Fig. 2
Fig. 3
Packaging
Note
Unit
100 pieces
Male with cord
Male with chain
Female with chain
11-16
TNC 75 Ω
PLUGS
STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLE
Cable group
6 / 75 + 93
Part number
Captive center contact
R144 085 000
no
R144 085 161
yes
Assembly
instructions
M02
Packaging
Note
Unit
Full crimp
100 pieces
Commercial version - full crimp
STRAIGHT PLUG CLAMP TYPE FOR FLEXIBLE CABLE
Cable group
Part number
Captive center contact
Assembly
instructions
Packaging
8 / 75
R144 017 000
yes
M09
Unit
11-17
TNC 75 Ω
JACKS AND ADAPTERS
STRAIGHT BULKHEAD JACKS CRIMP TYPE FOR FLEXIBLE CABLE
Cable group
6 / 75 + 93
Part number
Captive center contact
R144 334 000
no
R144 334 161
yes
Panel drilling
Assembly
instructions
P09 or P11
M02
Packaging
Note
Unit
Panel sealed
100 pieces
Commercial
version - panel
sealed
STRAIGHT BULKHEAD JACK, CRIMP TYPE, FOR FLEXIBLE CABLE
Cable group
Part number
Captive center contact
Assembly instructions
Panel drilling
Packaging
Note
6 / 75
R144 329 000
yes
M07
P09
Unit
Panel sealed
IN SERIES ADAPTERS
Fig. 1
Part number
Fig
R144 704 000
1
R144 770 000
2
Fig. 2
Captive center contact
Packaging
yes
Unit
11-18
TNC 18 GHz
TEST/CHARACTERISTICS
CHARACTERISTICS
MIL-C-39012 A
VALUES/REMARKS
ELECTRICAL CHARACTERISTICS
Impedance
50 Ω
Frequency range
DC - 18 GHz
V.S.W.R.
3-14
Semi–rigid cable: 1.17 max
Insertion loss
3-27
0.18 dB max at 9 GHz
RF leakage
3-26
-60 dB min from 2 to 3 GHz
Insulation resistance
3-11
5000 MΩ min
Contact resistance
center contact (mΩ)
outer contact (mΩ)
3-16
Flexible cable: 1.35 at 12.4 GHz
Working voltage
In series adapter: 1.35 max
Initial
1.5
0.2
After proof
2
-
At sea level: 500 V rms
at 70000 ft (21000 m): 125 V rms
Dielectric withstanding voltage
3-17
At sea level: 1500 V rms
at 70000 ft (21000 m): 375 V rms
RF withstanding voltage
3-23
At sea level: 1000 V rms (5 MHz sine wave)
MECHANICAL CHARACTERISTICS
Durability
3-15
500 matings
Mating / unmating
Axial force: not applicable
Torque: 1.96 inch pounds (22.6 N.cm)
Recommended mating torque
22.98 inch pounds (265 N.cm)
Proof torque
29.40 inch pounds (339 N.cm)
Coupling mechanism retention force
3-25
100 Lbf (44.5 daN)
Cabling retention force
3-24
51 Lbf (227 N min)
(cable dia. .189 (4.8) to .228 (5.8))
76.4 Lbf (340 N min)
(cable dia. .250 (6.35) and above)
Center contact retention
Axial: 6.06 Lbf (27 N)
ENVIRONMENTAL CHARACTERISTICS
Temperature range
Standard models
Hermetic sealed models
Models for semi–rigid cables
Combined climate tests
Thermal shock
High temperature endurance
Corrosion (salt spray)
Vibrations
Shocks
Moisture resistance
Low pressure
Hermetic seal
3-20
3-13
3-18
3-19
3-21
3-22
–65°C / + 165°C
–65°C / +100°C
–65°C / +105°C
MIL–STD–202, method 107, condition B
MIL–STD–202, method 108
MIL–STD–202, method 101, condition B
MIL–STD–202, method 204, condition B
MIL–STD–202, method 213, condition G
MIL–STD–202, method 106
Not applicable
Applied vacuum 10-6 mm of Hg (Torrs)
Leakage rate < 10-6 atm/cm3/s
Pressure 3.5 bars; duration 2 mn; temperature 15°C to 25°C
Leakage
MATERIALS
Body
Center contact
Ferrules
Insulators
Gaskets
male
female
Stainless steel
Brass
Bronze
Brass
PTFE teflon
Silicone elastomer
PLATING
Body
Center contacts
Standard packaging = unit
Passivated
Gold plated
All dimensions are given in mm (inch)
11-19
TNC 18 GHz
PLUGS AND JACKS
STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLE
Cable group
Part number
Dimensions mm(inch)
A
B
C
D
5 / 50 D
R143 082 700
30 (1.181)
1.05 (041)
3.2 (.126)
5.5 (.218)
11 / 50
R143 089 700
35 (1.378)
2.45 (.096)
7.5 (.295)
11.05 (.435)
Assembly instructions
M 02
STRAIGHT PLUGS SOLDER TYPE FOR SEMI-RIGID CABLE
Cable group
Part number
.141”
.250”
Dimensions mm(inch)
Assembly instructions
A
B
C
R143 051 700
1 (.039)
3.65 (.144)
5 (.197)
M 13
R143 054 700
1.7 (.067)
6.45 (.254)
8 (.315)
M 14
STRAIGHT JACKS SOLDER TYPE FOR SEMI-RIGID CABLE
Cable group
Part number
.141”
.250”
Dimensions mm(inch)
Assembly intructions
A
B
C
R143 227 700
1 (.039)
3.65 (.143)
5 (.197)
M 13
R143 228 700
1.7 (.067)
6.45 (.254)
8 (.315)
M 14
11-20
TNC 18 GHz
JACKS
STRAIGHT SQUARE FLANGE JACK CRIMP TYPE FOR FLEXIBLE CABLE
Cable group
Part number
Panel drilling
Assembly instructions
5 / 50 D
R143 292 700
P01
M 02
STRAIGHT SQUARE FLANGE JACKS SOLDER TYPE FOR SEMI-RIGID CABLE
Cable group
Part number
.141”
R143 273 700
.250”
R143 274 700
Dimensions mm(inch)
A
B
C
D
8 (.315)
1 (.039)
3.65 (.144)
5 (.197)
8.8 (.346)
1.7 (.067)
6.45 (.254)
8 (.315)
Panel drilling
P12
Assembly instructions
M 13
M 14
STRAIGHT BULKHEAD JACKS SOLDER TYPE FOR SEMI-RIGID CABLE
Cable group
Part number
.141”
.250”
Dimensions mm(inch)
A
B
C
R143 321 700
1 (.039)
3.65 (.144)
5 (.197)
R143 322 700
1.7 (.067)
6.45 (.254)
8 (.315)
Panel drilling
P09
Assembly intructions
M 13
M 14
11-21
TNC 18 GHz
RECEPTACLES
SQUARE FLANGE STRAIGHT MALE RECEPTACLE (extended dielectric - stub contact)
Part number
Captive center contact
Panel drilling
R143 446 700
yes
P14
SQUARE FLANGE STRAIGHT FEMALE RECEPTACLE
Part number
Captive center contact
Panel drilling
R143 410 700
yes
P15
SQUARE FLANGE STRAIGHT FEMALE RECEPTACLE (extended dielectric - stub contact)
Part number
Captive center contact
R143 412 700
yes
R143 413 700
no
Panel drilling
P13
11-22
TNC 18 GHz
ADAPTERS AND CAP
IN SERIES ADAPTERS
Fig. 2
Fig. 1
Fig. 3
Fig. 4
Part number
Fig.
R143 703 700
1
R143 704 700
2
R143 705 700
3
Fig. 5
Captive center contact
Panel drilling
Note
Male - male
Female - female
yes
Male - female
R143 710 700
4
P16
Square flange female - female
R143 730 700
5
P09
Bulkhead panel sealed female - female
SHORT CIRCUIT CAP
Part number
R143 850 700
11-23
TNC
PANEL DRILLING
P01
P02
P05
P06
P09
P13
P10
P14
P03
P07
P11
P15
P04
P08
P12
P16
11-24
TNC
ASSEMBLY INSTRUCTIONS
M 01
STRIPPING DIMENSIONS
Centre contact
Ferrule
Body
Heatshrink sleeve (option)
Part number
R143 182 000
Stripping length (mm)
Crimp tools
a
b
c
e
Dies included
MIL standard R282 293 000 (M22520/5-01) + dies
4
8.5
15
11
R282 223 000 Hex 1.73-5.41
R282 235 011 (M22520/5-11) Hex 1.73-5.41
1
4
-
Slide the heatshrink sleeve onto the cable (option).
Slide the ferrule onto the cable.
Strip the cable.
-
Slide the cable into the body until it bottoms
against the insulator.
-
Slide the ferrule over the braid.
Crimp the ferrule with crimping tool (see table).
-
Cut the excess of braid if necessary.
Slide the sleeve over the ferrule and heatshrink it
in place (option).
5
2
-
Slide the center contact on until it bottoms against the
cable dielectric.
Solder the center contact.
Clean solder area.
6
3
-
Fan the braid.
11-25
TNC
ASSEMBLY INSTRUCTIONS
M 02
Centre contact
STRIPPING DIMENSIONS
Ferrule
Body
Heatshrink sleeve (option)
Part number
a
Stripping length (mm)
b
c
Crimp tools
MIL standard R282 293 000 (M22520/5-01) + dies
e
Dies included
R282 223 000
Hex 1.73-5.41
R282 235 011 (M22520/5-11) Hex 1.73-5.41
R282 231 000
Hex 2.54-10.54
R282 231 000 Hex 10.54
R143 082 000
R143 082 161
R143 082 700
4
8.5
15
11
2.5
6.5
11.5
9
R143 089 700
3
6
14
10
R143 292 700
R143 235 161
R143 332 161
R144 085 000
R144 085 161
R144 334 000
R144 334 161
2.5
6.5
11.5
9
R282 235 011 (M22520/5-11) Hex 1.73-5.41
4
8.5
15
11
R282 223 000
Hex 1.73-5.41
1
R282 235 013 (M22520/5-11) Hex 1.73-6.48
4
-
Slide the heatshrink sleeve onto the cable (option).
Slide the ferrule onto the cable.
Strip the cable.
-
Slide the cable into the body until it bottoms
against insulator.
-
Slide the ferrule over the braid.
Crimp the ferrule with crimping tool (see table).
-
Cut the excess of braid if necessary.
Slide the sleeve over the ferrule and heatshrink it
in place (option).
5
2
-
Slide the center contact on until it bottoms against the
cable dielectric.
Crimp the center contact with crimping tool (see
table).
6
3
-
Fan the braid.
11-26
TNC
ASSEMBLY INSTRUCTIONS
M 03
STRIPPING DIMENSIONS
Clamp braid
Centre contact
Ferrule
Body
Insulator
Part number
R143 075 000
R143 075 161
R143 237 000
R143 331 161
Stripping length (mm)
Crimp tools
a
b
c
e
Dies included
MIL standard R282 293 000 (M22520/5-01) + dies
4
10
18.5
14.5
R282 223 000 Hex 1.73-5.41
R282 235 011 (M22520/5-11) Hex 1.73-5.41
1
4
-
Slide the ferrule onto the cable.
Strip the cable.
-
Slide cable into body until it bottoms against
insulator.
2
1
1
2
5
-
Fan the braid.
Slide the braid clamp and the insulator between the
dielectric and the braid.
Slide the insulator between the dielectric and the
braid.
-
Slide the ferrule over the braid.
1
1
2
3
3
6
-
Slide on the center contact until it bottoms against the
cable dielectric.
Solder or crimp the center contact with crimping tool
(see table).
Clean solder area if necessary.
-
Crimp the ferrule with crimping tool (see table).
Cut the excess of braid if necessary.
2
1
2
1
11-27
TNC
ASSEMBLY INSTRUCTIONS
M 04
STRIPPING DIMENSIONS
Cap
Ferrule
Body
Heatshrink sleeve (option)
Stripping length (mm)
Part number
a
b
Crimp tools
c
e
Dies included
MIL standard R282 293 000 (M22520/5-01) + dies
R143 181 161
2.5
6.5
16
13.5
R282 211 000 Hex 3.25
R282 235 003 (M22520/5-03) Hex 3.25
R143 182 161
2
7.5
16
14
R282 223 000 Hex 5.41
R282 235 011 (M22520/5-11) Hex 5.40
1
4
-
Slide the heatshrink sleeve onto the cable (option).
Slide the ferrule onto the cable.
Strip the cable.
-
Crimp the ferrule with crimping tool (see table).
Solder the inner conductor.
2
3
1
2
1
5
2
-
-
Fan the braid.
Place the cap into the body.
1
1
6
3
-
-
Push the connector body under the braid.
Slide the ferrule over the braid.
-
Press on the cap flush or slightly below the surface
of the body assembly.
Slide the sleeve over the ferrule and heatshrink it
in place (option).
2
1
1
2
11-28
TNC
ASSEMBLY INSTRUCTIONS
M 05
STRIPPING DIMENSIONS
Centre contact
Back nut
Ferrule
Body
Heatshrink sleeve (option)
Stripping length (mm)
Part number
a
R143 072 000
7
R143 074 000
b
c
8.5
26
Crimp tools
e
19
Dies included
MIL standard R282 293 000 (M22520/5-01) + dies
R282 223 000 Hex 1.73-5.41
R282 235 011 (M22520/5-03) Hex 1.73-5.41
R282 223 000 Hex 1.73-6.48
R282 235 013 (M22520/5-11) Hex 1.73-6.48
1
4
-
Slide the heatshrink sleeve onto the cable (option).
Slide the ferrule onto the cable.
Position the ferrule's hole at the front if soldering.
Position the ferrule's hole at the back if crimping.
Strip the cable.
4
3
5
-
Slide the center contact on until it bottoms against
the insulator back nut.
Solder or crimp the contact (see table).
2
1
1
2
5
2
-
-
Fan the braid.
Slide the cable into the back nut.
-
Screw the back nut into the connector body with
the adapted wrench.
Recommended coupling torque (see table).
1
1
2
3
-
Slide the ferrule over the braid.
Crimp the ferrule with crimping tool (see table).
1
6
-
Slide the sleeve over the ferrule and heatshrink it
in place (option).
1
2
11-29
TNC
ASSEMBLY INSTRUCTIONS
M 06
Centre contact
STRIPPING DIMENSIONS
Insulator
Gasket
Clamp braid
Back nut
Body
Stripping length (mm)
Part number
R143 004 000
R143 254 000
a
b
c
e
4
2
9
5
1
Coupling torque
450 N.cm
4
-
Slide the back nut onto the cable.
Strip the cable.
Cut 2 slots in the jacket if necessary.
-
Solder the center contact onto the inner conductor.
Slide the back nut over the cable assembly.
2
1
2
1
2
5
-
Slide the clamp braid sleeve between the cable
dielectric and the braid.
-
Mount the gasket into the body.
1
1
3
6
-
Cut the braid flush with the clamp braid sleeve.
Slide the spacer onto the cable.
Slide the center contact on until it bottoms against the
cable dielectric.
-
Screw sub-assembly into the connector body with
the adapted wrench.
Recommended coupling torque (see table).
1
2
3
1
11-30
TNC
M 07
ASSEMBLY INSTRUCTIONS
’V’ groove gasket
Washer
STRIPPING DIMENSIONS
Centre contact
Clamp braid
Body
Back nut
Stripping length (mm)
Part number
a
R143 008 000
2.5
R143 012 000
R143 018 000
e
5
1.5
7
3
9
3
R143 156 000
b
R143 258 000
2.5
R143 325 000
R144 329 000
1
450 N.cm
1
800 N.cm
2.5
7
R143 207 000
Coupling torque
3
5
1.5
7
3
450 N.cm
4
-
Strip the cable as shown in sketch 1.
1
-
Slide the back nut over the cable assembly.
Slide the center contact onto the inner conductor.
2
1
2
-
Slide the back nut, the washer and the 'V' groove
gasket onto the cable.
Slide the clamp braid sleeve over the braid.
5
-
1
1
2
3
6
-
Solder the center contact onto the inner conductor.
Fold the braid back and trim off the extra braid.
Trim dielectric back as shown in sketch 2.
-
Screw sub-assembly into the connector body with
the adapted wrench.
Recommended coupling torque (see table).
2
1
11-31
TNC
ASSEMBLY INSTRUCTIONS
M 08
Clamp braid
Solder barrel
Centre contact
’V’ groove gasket
STRIPPING DIMENSIONS
Insulator
Washer
Back nut
Body
We recommend a cable thermal preconditioning before assembly
Part number
Stripping length b (mm)
Coupling torque
R143 052 000
5.2
450 N.cm
1
4
-
Strip the cable.
Trim the cable inner conductor.
Clean the cable.
1
Slide the insulator onto the cable inner conductor.
Slide the center contact on until it bottoms against
the insulator.
2
1
2
2
5
-
Slide the back nut, the washer, the 'V' groove gasket,
the clamp braid sleeve and the solder barrel onto the
cable.
-
Solder the center contact onto the inner conductor.
Assemble the components.
1
2
1
3
6
-
Position the solder barrel and the cable flush against
the solder barrel gauge.
Solder the solder barrel onto the cable.
After cooling, remove the solder barrel gauge.
-
Screw sub-assembly into the connector body with
the adapted wrench.
Recommended coupling torque (see table).
1
2
3
1
Gauge
11-32
TNC
M 09
Part number
R144 017 000
ASSEMBLY INSTRUCTIONS
Clamp nut Washer Gasket Braid clamp sleeve
Centre contact
Body
STRIPPING DIMENSIONS
b
Stripping length (mm)
a
b
e
3
10
3.5
1
3
-
Strip the cable.
-
Solder the cable inner conductor into center
contact.
Solder
2
4
-
Slide the clamp nut, the washer and the gasket onto
the cable.
Slide clamp braid sleeve over braid.
Fold back braid and trim off surplus braid.
Trim back dielectric as shown.
-
Screw sub-assembly into the connector body.
Recommended coupling torque 450 N.cm.
e
a
Hex.: .16 /flats
11-33
TNC
ASSEMBLY INSTRUCTIONS
M 10
Ferrule
Back body
Centre contact
STRIPPING DIMENSIONS
Body
b
a
c
Part number
R143 073 000
Stripping length (mm)
e
Crimp tools
a
b
c
e
Dies included
MIL standard R282 293 000 (M22520/5-01) + dies
7
8.5
26
19
R282 223 000 Hex 1.73-5.4
R282 235 011 (M22520/5-11) Hex 1.73-5.41
1
3
-
Slide onto the cable the ferrule.
Strip the cable.
-
Crimp the ferrule with crimping tool.
Slide on the center contact until it bottoms against
insulator.
Crimp center contact with crimping tool.
Crimp area
Crimp area
2
4
-
Fan the braid.
Slide the back body between dielectric and braid.
Slide ferrule over the braid (in direction F).
Ferrule
-
Mount gasket into connector.
Screw sub-assembly into the connector body
(recommended coupling torque 450 N.cm 39825 in.lb).
F
Hex.: 11 mm/flats
11-34
TNC
M 11
ASSEMBLY INSTRUCTIONS
Clamp nut Clamp braid sleeve Gasket Spacer
Centre contact
Body
STRIPPING DIMENSIONS
c
b
a
e
Part number
R143 324 000
Stripping length (mm)
a
b
c
e
4
2
9
5
1
3
-
Slide clamp nut onto cable.
Strip the cable.
Cut 2 slots in the jacket if necessary.
-
Solder center contact onto cable center conductor.
Slide back nut over clamp assembly.
Solder
2
4
-
Slide the clamp braid sleeve between cable dielectric
and braid.
Cut the braid flush with the clamp braid sleeve.
Slide the spacer onto the cable.
-
Mount gasket into connector.
Screw sub-assembly into the connector body
(recommended coupling torque 450 N.cm 39825 in.lb).
Hex.: 11 mm/flats
11-35
TNC
M 12
ASSEMBLY INSTRUCTIONS
Insulator
Centre contact
STRIPPING DIMENSIONS
Body
a
Part number
Stripping length a (mm)
Positioner
R143 257 440
4
R282 744 400
1
3
-
Strip the cable.
Clean the cable.
-
Screw positioner onto connector.
Slide sub-assembly into the connector body (in
direction F).
Body
F
2
4
-
Slide insulator onto the cable center conductor.
Solder center contact onto cable center conductor.
Clean solder area.
Solder
-
Solder the cable into body of connector.
After cooling remove positioner and clean
soldered area.
Solder
11-36
TNC
ASSEMBLY INSTRUCTIONS
M 13
Body
Centre contact
Insulator
Solder sleeve
STRIPPING DIMENSIONS
Distance-piece
We recommend a thermal preconditionning cable
Stripping length Center contact
a (mm)
positioner
Part number
R143 051 700
R143 227 700
R143 273 700
R143 321 700
3
Cable
positioner
Solder gauge
thickness
0.5 mm
Soldering jig
Milling cutter
Lock jig
Torque wrench
R282 744 271 R282 744 003 R282 740 000 R282 862 100 R282 915 020 R282 370 020 R282 321 020
1
3
-
Strip the cable with the cable stripping tool.
Trim the cable inner conducteur with the trimmer.
Clean the cable.
Screw the positioner onto the soldering jig.
Slide the cable assembly until it bottoms against
positioner.
Tighten and solder the contact.
-
After cooling, remove the assembly from the jig.
Trim dielectric recess with the milling cutter.
Milling cutter
Solder sleeve
Cable
Tighten
Centre contact
Gauge
Cable
4
Positioner
Slide the distance-piece on the solder sleeve.
Slide insulator on the center contact.
Soldering jig
Insulator
Distance-piece
Solder sleeve
Center contact
2
-
After cooling remove cable assembly from the jig.
Slide positioner into the solder sleeve.
Get in solder sleeve assembly onto the soldering jig
and slide the cable until it bottoms against positioner.
Tighten.
Put 3 rings of solder around the cable and solder.
Cable in position
Tighten
5
-
Slide the connector on the sleeve and lock it.
Lock jig
Solder
Solder sleeve
Positioner
Soldering jig
11-37
TNC
ASSEMBLY INSTRUCTIONS
M 14
Body
Centre contact
Insulator
Solder sleeve
Distance-piece
STRIPPING DIMENSIONS
We recommend a thermal preconditionning cable
Part number
Stripping
length Stripping tool
a (mm)
R143 054 700
R143 228 700
R143 274 700
R143 322 700
Center contact
Soldering jig
positioner
Trimmer
Cable
positioner
Milling cutter
Lock jig
Torque wrench
R282 744 271 R282 740 000 R282 744 003 R282 915 020 R282 370 020
3
R282 054 000 R282 074 010
Or tool box for TNC 18 for semi rigid cable R282 122 010
1
R282 321 020
3
-
Strip the cable with the cable stripping tool.
Trim the cable inner conducteur with the trimmer.
Clean the cable.
Screw the positioner onto the soldering jig.
Slide the cable assembly until it bottoms against
positioner.
Tighten and solder the contact.
-
After cooling, remove the assembly from the jig.
Trim dielectric recess with the milling cutter.
Milling cutter
Solder sleeve
Cable
Tighten
Centre contact
Gauge
Cable
4
Positioner
Slide the distance-piece on the solder sleeve.
Slide insulator on the center contact.
Soldering jig
Insulator
Distance-piece
Solder sleeve
Center contact
2
-
After cooling remove cable assembly from the jig.
Slide positioner into the solder sleeve.
Get in solder sleeve assembly onto the soldering jig
and slide the cable until it bottoms against positioner.
Tighten.
Put 3 rings of solder around the cable and solder.
Cable in position
Tighten
5
-
Slide the connector on the sleeve and lock it.
Lock jig
Solder
Solder sleeve
Positioner
Soldering jig
11-38