Emerson AV101 Service manual

SERVICE MANUAL
27" COLOR TELEVISION
6427FD/EWF2703
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service
operations. Some of these service special tools should be used when and
as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk of
personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai
could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous
consequences of each way. Consequently, Funai has not undertaken any
such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
TABLE OF CONTENTS
Specifications ........................................................
Important Safety Precautions................................
Standard Notes for Servicing ................................
Disassembly Instructions ......................................
Electrical Adjustment Instructions .........................
Block Diagram.......................................................
Schematic Diagram / CBA's and Test Points .......
Schematic Diagram ..............................................
1-1
2-1
3-1
4-1
5-1
6-1
7-1
7-3
CBA Views and Test Points.................................. 7-11
Wave Forms .......................................................... 8-1
Wiring Diagram...................................................... 9-1
IC Pin Function .................................................... 10-1
Cabinet Exploded View ....................................... 11-1
Packing Exploded View ....................................... 11-3
Mechanical Parts List .......................................... 12-1
Electrical Parts List .............................................. 13-1
SPECIFICATIONS
<TUNER>
ANT. Input ------------------- 75ohm Unbal., F type
Reference Level ----------- 20Vp-p (CRT Green Cathode)
Test Input Signal ---------- 400Hz 30% modulation
Description
Condition
Unit
Nominal
Limit
1. Intermediate Freq.
Picture
Sound
MHz
MHz
45.75
41.25
-
2. Peak Picture Sens
VHF
CATV
UHF
dBµv
dBµv
dBµv
15
15
15
30
30
40
-
MHz
±2.0
±0.7
Condition
Unit
Nominal
Limit
1. Deflection Freq.
Horizontal
Vertical
KHz
Hz
15.734
60
-
2. Linearity
Horizontal
Vertical
%
%
-
±15
±10
3. Over Scan
-
%
10
-
4. High Voltage
-
KV
29
-
Condition
Unit
Nominal
Limit
Center
Side
Corner
mm
mm
mm
-
0.4
1.5
2.1
APL 100%
Ft-L
25
15
-
°K
9200°K
-
Horizontal
Vertical
Line
Line
250
300
-
3. AFT Pull In Range (10mV input)
<DEFLECTION>
Description
<VIDEO & CHROMA>
Description
1. Misconvergence
2. Brightness
3. Color Temperature
4. Resolution
<AUDIO>
All items are measured across 8Ω load at speaker output terminal.
Description
1. Audio Output Power
2. Audio Distortion (w/LPF)
3. Audio Freq. Response
Condition
Unit
Nominal
Limit
10% THD
W
1
0.8
500mW
%
2
7
-3dB
Hz
70~11K
-
Note:
Nominal specifications represent the design specifications. All units should be able to approximate
these. Some will exceed and some may drop slightly below these specifications. Limit specifications
represent the absolute worst condition that still might be considered acceptable. In no case should
a unit fail to meet limit specifications.
1-1
L6200SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for TV Circuit
age current tester or a metering system that complies with American National Standards Institute
(ANSI) C101.1 Leakage Current for Appliances
and Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on position and then in the off position, measure from a
known earth ground (metal water pipe, conduit,
etc.) to all exposed metal parts of the instrument
(antennas, handle brackets, metal cabinet, screw
heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current
measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet
and repeat the test.
1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following
items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing.
(1) Protective shields are provided on this chassis
to protect both the technician and the customer.
Correctly replace all missing protective shields, including any removed for servicing convenience.
(2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place
all protective devices, including but not limited to,
nonmetallic control knobs, insulating fishpapers,
adjustment and compartment covers/shields, and
isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated
without all protective devices correctly installed and functioning. Servicers who defeat
safety features or fail to perform safety checks
may be liable for any resulting damage.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
LEAKAGE
CURRENT
TESTER
_
+
TEST ALL EXPOSED
METAL SURFACES
b. Be sure that there are no cabinet openings through
which an adult or child might be able to insert their
fingers and contact a hazardous voltage. Such
openings include, but are not limited to, (1) spacing between the picture tube and the cabinet
mask, (2) excessively wide cabinet ventilation
slots, and (3) an improperly fitted and/or incorrectly
secured cabinet back cover.
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug prongs.
Place the instrument AC switch in the on position.
Connect one lead of an ohmmeter to the AC plug
prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the
coaxial connector. If the measured resistance is
less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected
before the instrument is returned to the customer.
Repeat this test with the instrument AC switch in
the off position.
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE LIMITS
SPECIFIED HEREIN INDICATE A POTENTIAL
SHOCK HAZARD THAT MUST BE ELIMINATED
BEFORE RETURNING THE INSTRUMENT TO
THE CUSTOMER OR BEFORE CONNECTING
THE ANTENNA OR ACCESSORIES.
e. X-Radiation and High Voltage Limits - Because
the picture tube is the primary potential source of
X-radiation in solid-state TV receivers, it is specially constructed to prohibit X-radiation emissions.
For continued X-radiation protection, the replacement picture tube must be the same type as the
original. Also, because the picture tube shields
and mounting hardware perform an X-radiation
protection function, they must be correctly in place.
High voltage must be measured each time servic-
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line
cord directly into a 120V AC outlet. (Do not use an
isolation transformer during this test.) Use a leak-
2-1
L6115IMP
earth ground. If a voltage reading in excess of 1.0V
is obtained, remove and reinsert the AC power
plug in the opposite polarity and again measure
the voltage potential between the chassis and a
known earth ground.
ing is performed that involves B+, horizontal deflection or high voltage. Correct operation of the Xradiation protection circuits also must be reconfirmed each time they are serviced. (X-radiation
protection circuits also may be called "horizontal
disable" or "hold down.") Read and apply the high
voltage limits and, if the chassis is so equipped,
the X-radiation protection circuit specifications given on instrument labels and in the Product Safety
& X-Radiation Warning note on the service data
chassis schematic. High voltage is maintained
within specified limits by close tolerance safety-related components/adjustments in the high-voltage
circuit. If high voltage exceeds specified limits,
check each component specified on the chassis
schematic and take corrective action.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can
be safety-serviced only with an isolation transformer inserted in the power line between the receiver
and the AC power source, for both personnel and
test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation
material that must not be defeated or altered.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the
receiver chassis, or on the picture tube.
6. Observe original lead dress. Take extra care to assure correct lead dress in the following areas:a.
near sharp edges,b. near thermally hot parts-be
sure that leads and components do not touch thermally hot parts,c. the AC supply,d. high voltage,
and,e. antenna wiring. Always inspect in all areas
for pinched, out of place, or frayed wiring. Check
AC power cord for damage.
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV receiver. Design alterations and additions, including,
but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video
output connections, might alter the safety characteristics of this receiver and create a hazard to the
user. Any design alterations or additions will void
the manufacturer's warranty and may make you,
the servicer, responsible for personal injury or
property damage resulting therefrom.
7. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or wiring that meet original specifications. Additionally,
determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
4. Picture Tube Implosion Protection Warning The picture tube in this receiver employs integral
implosion protection. For continued implosion protection, replace the picture tube only with one of
the same type number. Do not remove, install, or
otherwise handle the picture tube in any manner
without first putting on shatterproof goggles
equipped with side shields. People not so
equipped must be kept safely away while picture
tubes are handled. Keep the picture tube away
from your body. Do not handle the picture tube by
its neck. Some "in-line" picture tubes are equipped
with a permanently attached deflection yoke; because of potential hazard, do not try to remove
such "permanently attached" yokes from the picture tube.
8. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual
inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc.. Parts
that have special safety characteristics are identified by a ( # ) on schematics and in parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire, and/or
other hazards. The product's safety is under review continuously and new instructions are issued
whenever appropriate. Prior to shipment from the
factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which
they are to be sold. However, in order to maintain
such compliance, it is equally important to implement the following precautions when a set is being
serviced.
5. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord
and maybe safety-serviced without an isolation
transformer only if the AC power plug is inserted
so that the chassis is connected to the ground side
of the AC power source. To confirm that the AC
power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known
2-2
L6115IMP
Precautions during Servicing
3) Align the lengths of the wires to be connected. Insert the wires fully into the connector.
A. Parts identified by the ( # ) symbol are critical for
safety.
Replace only with part number specified.
4) Use the crimping tool to crimp the metal sleeve at
the center position. Be sure to crimp fully to the
complete closure of the tool.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations applying to spurious radiation. These must also be
replaced only with specified replacements.
L. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. Crimp type wire connector
The power transformer uses crimp type connectors which connect the power cord and the primary
side of the transformer. When replacing the transformer, follow these steps carefully and precisely
to prevent shock hazards.
Replacement procedure
1) Remove the old connector by cutting the wires at
a point close to the connector.
Important: Do not re-use a connector (discard it).
2) Strip about 15 mm of the insulation from the ends
of the wires. If the wires are stranded, twist the
strands to avoid frayed conductors.
2-3
L6115IMP
Safety Check after Servicing
Examine the area surrounding the repaired location
for damage or deterioration. Observe that screws,
parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance
with safety standards.
Chassis or Secondary Conductor
Primary Circuit Terminals
d'
d
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1 : Ratings for selected area
AC Line Voltage
Region
Clearance
Distance (d) (d')
110 to 130 V
USA or
CANADA
≥ 3.2 mm
(0.126 inches)
Fig. 1
Exposed Accessible Part
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
Z
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
AC Voltmeter
(High Impedance)
1.5kΩ
0.15µF
B
Measuring Method : (Power ON)
Earth Ground
Power Cord Plug Prongs
Fig. 2
Insert load Z between B (earth ground, power cord
plug prongs) and exposed accessible parts. Use an
AC voltmeter to measure across both terminals of
load Z. See Fig. 2 and following table.
Table 2 : Leakage current ratings for selected areas
AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
USA
0.15µF CAP. & 1.5kΩ
RES. connected in
parallel
i≤0.5mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4
L6115IMP
STANDARD NOTES FOR SERVICING
Circuit Board Indications
(2) Remove the flat pack-IC with tweezers while applying the hot air.
a. The output pin of the 3 pin Regulator ICs is indicated as shown.
Top View
Out
(3) Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Bottom View
In
Input
(4) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Caution:
b. For other ICs, pin 1 and every fifth pin are indicated as shown.
1. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
5
Pin 1
2. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when removing it.
10
c. The 1st pin of every male connector is indicated as
shown.
CBA
Pin 1
Hot-air
Flat Pack-IC
Desoldering
Machine
How to Remove / Install Flat Pack-IC
1. Removal
Masking
Tape
Tweezers
With Hot-Air Flat Pack-IC Desoldering Machine:
(1) Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about
5 to 6 seconds). (Fig. S-1-1)
Flat Pack-IC
Fig. S-1-2
Fig. S-1-1
3-1
L6115STA
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
With Soldering Iron:
(1) Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Flat Pack-IC
(5) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note:
When using a soldering iron, care must be taken to
ensure that the flat pack-IC is not being held by
glue. When the flat pack-IC is removed from the
CBA, handle it gently because it may be damaged
if force is applied.
Desoldering Braid
Hot Air Blower
Soldering Iron
Fig. S-1-3
or
(2) Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering machine.(Fig. S-1-4)
Iron Wire
Soldering Iron
To Solid
Mounting Point
Sharp
Pin
Fine Tip
Soldering Iron
CBA
Fig. S-1-5
Fine Tip
Soldering Iron
Fig. S-1-4
(3) Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Flat Pack-IC
Tweezers
(4) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Fig. S-1-6
With Iron Wire:
(1) Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
(2) Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
(3) While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
(4) Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
3-2
L6115STA
Instructions for Handling
Semiconductors
2. Installation
(1) Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
Electrostatic breakdown of the semiconductors may
occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
(2) The "I" mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
pre- solder the four corners of the flat pack-IC.
(See Fig. S-1-8.)
1. Ground for Human Body
Be sure to wear a grounding band (1MΩ) that is properly grounded to remove any static electricity that may
be charged on the body.
(3) Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1MΩ) on the workbench or
other surface, where the semiconductors are to be
placed. Because the static electricity charge on clothing will not escape through the body grounding band,
be careful to avoid contacting semiconductors with
your clothing.
Example :
<Incorrect>
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Fig. S-1-7
Presolder
CBA
<Correct>
Grounding Band
Flat Pack-IC
CBA
Fig. S-1-8
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-3
L6115STA
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
Note :
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order.These numbers
are also used as the Identification (location) No. of
parts in figures.
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
Caution !
(4) Identification of part to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered.
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
S=Screw, P=Spring, L=Locking Tab, CN=Connector, *=Unhook, Unlock, Release, Unplug, or
Desolder
[1] Rear Cabinet
2(S-2) = two Screws (S-2)
(5) Refer to the following "Reference Notes in the
Table."
[2] CRT CBA
Reference Notes in the Table
[3] Main CBA
1. Removal of the Rear Cabinet. Remove screws
7(S-1), 3(S-2) and 1(S-3) then slide the Rear Cabinet backward.
2. Removal of the CRT CBA. Disconnect CN501 then
pull the CRT CBA backward.
[4] CRT
3. Removal of the Main CBA. Disconnect CN571 on
the Main CBA then slide the Main CBA backward.
2. Disassembly Method
Caution !
Removal
Step/
Loc. No.
Part
Fig.
No
Remove/*unlock/
release/unplug/
unclamp/desolder
Note
4. Removal of the CRT. Remove screws 4(S-4) and
Anode Cap. then slide the CRT backward.
[1]
Rear
Cabinet
1,2
7(S-1), 3(S-2),
1(S-3)
1
[2]
CRT CBA
4,5
CN501
2
[3]
Main CBA
3,5
[4]
CRT
↓
(1)
↓
(2)
4
↓
(3)
CN571
3
4(S-4), CN691
4
↓
(4)
Discharge the Anode Lead of the CRT with the CRT
Ground Wire before removing the Anode Cap.
↓
(5)
4-1
L6610DC
S-1
Front Cabinet
[3] Main CBA
S-3
Control Plate
S-2
S-1
[1] Rear Cabinet
Fig. 1
Fig. 3
Anode Cap
S-1
[1] Rear Cabinet
CRT
Ground Wire
S-1
Front
Cabinet
Degaussing
Coil
[2] CRT
CBA
S-4
S-2
Front Cabinet
S-4
S-4
S-1
S-3
[4] CRT
S-1
S-4
S-1
Control Plate
Control Plate
Fig. 4
Fig. 2
4-2
L6610DC
TV Cable Wiring Diagram
SP802
SP801
L691 DEGAUSSING COIL
CLN802
CLN801
MAIN CBA
CN801
CN802
WH301A
CN691
TU1
TUNER
FLYBACK TRANSFORMER
T571
CN571
WH501A
AC601
AC CORD
FOCUS
SCREEN
WH301B
WH501B
ANODE
CN1501
TO CRT GROUND
4-3
Fig. 5
L6610DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
How to set up the service mode:
General Note:
"CBA" is abbreviation for "Circuit Board Assembly."
NOTE:
Service mode:
1. Use the service remote control unit.
2. Turn the power on. (Use main power on the TV
unit.)
3. Press "SLEEP" button on the service remote control unit. Version of micro computer will display on
the CRT. (Ex: 054-0.05)
4. Check the display on the lower left is "2812" and if
it is not "2812," set it at "2812" according to "2. Initial Setting."
Electrical adjustments are required after replacing
circuit components and certain mechanical parts.
It is important to perform these adjustments only
after all repairs and replacements have been completed.
Also, do not attempt these adjustments unless the
proper equipment is available.
Test Equipment Required
1. +B Adjustment
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
2. DC Voltmeter
3. Oscilloscope: Dual-trace with 10:1 probe,
V-Range:0.001~50V/Div,
F-Range: DC~AC-60MHz
4. Plastic Tip Driver
5. Remote control unit: Part No. N0138UD or N0139UD
6. DC power supply 13.2V/5A
Purpose: To obtain correct operation.
Symptom of Misadjustment: The picture is dark and
the unit does not operate correctly.
How to make Service remote control unit:
1. Prepare normal remote control unit. (Part No.
N0138UD or N0139UD) Remove 3 Screws from
the back lid. (Fig. 1-1)
2. Added J1 (Jumper Wire) to the remote control CBA.
(Fig. 1-2)
Test Point
Adj. Point
Mode
Input
TP601(+B)
TP300(GND)
VR661
---
---
Tape
M. EQ.
Spec.
---
DC Voltmeter
+138±0.5V DC.
Note: TP601, TP300(GND), VR661 --- Main CBA
1. Connect DC Volt Meter to TP601 and TP300(GND).
2. Adjust VR661 so that the voltage of TP601 becomes
+138±0.5V DC.
SCREWS
Fig. 1-1
J1
REMOTE CONTROL UNIT
REMOTE CONTROL CBA
Fig. 1-2
5-1
L6610EA
2. Initial Setting
S-CLR
General
1. Press "MENU" button on the service remote control unit. Then select "S-COLOR" (S-CLR) display.
1. Enter the Service mode. (See page 5-1)
2. Press "VOL p" button on the service remote control
unit. Display changes "C/D," "7F," "LANGUAGE,"
"ACCESS CODE," "SOUND TYPE," "VIDEO
TONE," "FM MODE," "V-OUT," "VIDEO," "AV
MEMO," "STABLE SOUND," "FILTER," "500," and
"YUV MEMORY" cyclically when "VOL p" button is
pressed.
3. To set the following each data value, press "CH o
/ p" buttons on the service remote control unit.
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "S-COLOR" (SCLR) becomes 56.
C-CLR
1. Press "MENU" button on the service remote control unit. Then select "COMPONENT COLOR" (CCLR) display.
7F --- Set to "FF."
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "COMPONENT
COLOR" (C-CLR) becomes 56.
LANGUAGE --- Set to "SPA."
TNT
ACCESS CODE --- Set to "OFF."
1. Press "MENU" button on the service remote control unit. Then select "TINT" (TNT) display.
SOUND TYPE --- Set to "MTS."
FM-MODE --- Set to "OFF."
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "TINT" (TNT) becomes 62.
V-OUT --- Set to "OFF."
V-TNT
VIDEO --- Set to "V1/V2/YUV."
1. Press "MENU" button on the service remote control unit. Then select "V-TINT" (V-TNT) display.
VIDEO TONE --- Set to "ON."
AV MEMO --- Set to "OFF."
FILTER --- Set to "ON."
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "V-TINT" (V-TNT)
becomes 62.
Adjusting the monitoring time --- Set to "500."
S-TNT
YUV MEMORY --- Set to "OFF."
1. Press "MENU" button on the service remote control unit. Then select "S-TINT" (S-TNT) display.
STABLE SOUND --- Set to "OFF."
3. Setting for BRIGHT, CONTRAST,
COLOR, TINT, and SHARPNESS
data Values
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "S-TINT" (S-TNT)
becomes 59.
C-TNT
General
1. Press "MENU" button on the service remote control unit. Then select "COMPONENT TINT" (CTNT) display.
1. Enter the Service mode. (See page 5-1)
2. Press "MENU" button on the service remote control
unit. Display changes "BRT," "CNT," "CLR," "SCLR," "C-CLR," "TNT," "V-TNT," "S-TNT," "CTNT," "SHARP," "S-SRP," and "C-SRP" cyclically when "MENU" button is pressed.
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "COMPONENT
TINT" (C-TNT) becomes 58.
SHARP
CNT
1. Press "MENU" button on the service remote control unit. Then select "SHARPNESS" (SHARP) display.
1. Press "MENU" button on the service remote control
unit. Then select "CONTRAST" (CNT) display.
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "CONTRAS" (CNT)
becomes 84.
2. Press "CH o/p" buttons on the service remote
control unit and select "47."
S-SRP
CLR
1. Press "MENU" button on the service remote control unit. Then select "S-SHARPNESS" (S-SRP)
display.
1. Press "MENU" button on the service remote control unit. Then select "COLOR" (CLR) display.
2. Press "CH o/p" buttons on the service remote
control unit so that the value of "COLOR" (CLR)
becomes 56.
2. Press "CH o/p" buttons on the service remote
control unit and select "47."
5-2
L6610EA
C-SRP
5. Purity Check
1. Press "MENU" button on the service remote control unit. Then select "COMPONENT SHARPNESS" (C-SRP) display.
1. Enter the Service mode. (See page 5-1)
2. Press "7" button on the remote control unit. Each
time pressing 7" button on the remote control unit,
display changes Red mode, Green mode, Blue
mode, and White mode cyclically.
2. Press "CH o/p" buttons on the service remote
control unit and select "47."
Note: BRIGHT data value does not need to be adjusted at this moment.
3. Select White mode.
4. Black Stretch Control Adjustment
4. Turn the power off and on again. (Main power button on the TV unit.)
Purpose: To show the fine black color.
6. SD Check Mode
Symptom of Misadjustment: Black color will not
appear correctly.
1. Enter the Service mode. (See page 5-1)
2. Press "1" button on the remote control unit. The
unit enter the SD-Check mode.
Note: Use service remote control unit.
1. Enter the Service mode. (See page 5-1)
2. Press "6" button on the service remote control unit.
"B-S" is indicated.
3. The unit starts selecting the added channel from
first channel according to the memorized CH ADD/
DELL data and CATV/TV data in RAM.
3. Press "CH o / p" buttons on the service remote control unit so that display will change "OFF," "0," and
"1." Then choose "B-S OFF."
SD Check mode (Factory mode)
Press "1" buton.
4. Press "6" button on the service remote control unit.
"B-S2" is indicated.
5. Press "CH o / p" buttons on the service remote
control unit so that display will change "0" and "1."
Then choose "B-S2 0."
7
Please wait
6. Turn the power off and on again, using the main
power button on the TV unit.
OSD color:
Magenta
There is no SD after
selecting channel.
13
Please wait
There are SD
in all channel.
OSD color:
Magenta
26
OK
30
NG
OSD color:
Magenta
OSD color:
Magenta
When SD-Check starting,
there is no ADD channel.
ADD nothing
OSD color:
Magenta
5-3
L6610EA
7. H. Position Adjustment
9. V. Position Adjustment
Purpose: To obtain correct horizontal position of
screen image.
Purpose: To obtain correct vertical width of screen
image.
Symptom of misadjustment: If V. Position is incorrect, vertical height of image on the screen may not be
properly displayed.
Symptom of Misadjustment: If H. Position is incorrect, horizontal position of image on the screen may
not be properly displayed.
Test Point
Adj. Point
Mode
Input
Test Point
Adj. Point
Mode
Input
---
CH o / p
buttons
RF
Monoscope
---
CH o / p
buttons
RF
Monoscope
Tape
M. EQ.
Spec.
Tape
M. EQ.
Spec.
---
Monoscope
90±5%
---
Monoscope
See below.
6. Turn the power off and on again. (Main power button on the TV unit.)
Note: Use service remote control unit
1. Operate the unit for at least 20 minutes.
2. Enter the Service Mode. (See page 5-1)
3. Receive the monoscope pattern.
4. Press "9" button on the service remote control unit
and select "V-P" mode. (Display change "V-S" and
"V-P" cyclically when "9" button is pressed).
5. Press "CH o/p" buttons on the service remote
control unit so that the top and bottom of the monoscope pattern will be equal of each other.
6. Turn the power off and on again. (Main power button on the TV unit.)
8. V. Size Adjustment
10. U-Pedestal Adjustment
Purpose: To obtain correct vertical width of screen image.
Symptom of Misadjustment: If V. Size is incorrect, vertical
size of image on the screen may not be properly displayed.
1. In VIDEO mode of V1, V2, or YUV, press "3" button
on the service remote control unit and select "UPED" mode. (Display changes "U-PED" and "VPED" cyclically when "3" button is pressed).
2. Switch the VIDEO mode to YUV. (Refer to “2. Initial
Setting.”)
3. To select one appropriate value in "0" to "15,"
press "CH o / p" buttons on the remote control
unit.
4. Switch the VIDEO mode to previous mode.
5. Turn the power off and on again. (Main power button on the TV unit.)
Note: Use service remote control unit
1. Operate the unit for at least 20 minutes.
2. Enter the Service mode. (See page 5-1)
3. Receive the monoscope pattern.
4. Press "8" button on the remote control unit.
"H-P" is indicated.
5. Press "CH o/p" buttons on the service remote
control unit so that the monoscope pattern will be
90±5% of display size and the circle is round.
Test Point
Adj. Point
Mode
Input
---
CH o / p
buttons
RF
Monoscope
Tape
M. EQ.
Spec.
---
Monoscope
90±5%
Note: Use service remote control unit.
1.
2.
3.
4.
Operate the unit for at least 20 minutes.
Enter the Service mode. (See page 5-1)
Receive the monoscope pattern.
Press "9" button on the service remote control unit
and select "V-S" mode. (Display changes "V-S" and
"V-P" cyclically when "9" button is pressed).
5. Press "CH o/p" buttons on the service remote
control unit so that the monoscope pattern will be
90±5% of display size and the circle is round.
6. Turn the power off and on again. (Main power button on the TV unit.)
11. V-Pedestal Adjustment
1. In VIDEO mode of V1, V2, or YUV, press "3" button
on the service remote control unit and select "VPED" mode. (Display changes "U-PED" and "VPED" cyclically when "3" button is pressed).
2. Switch the VIDEO mode to YUV. (Refer to “2. Initial
Setting.”)
3. To select one appropriate value in "0" to "15,"
press "CH o / p" buttons on the remote control
unit.
4. Switch the input mode to previous mode.
5. Turn the power off and on again. (Main power button on the TV unit.)
5-4
L6610EA
12. Software Reset
15. Cut-off Adjustment
To reset software, press “5” button on the remote control unit for at least 5 seconds after pressing “CH
RETURN” button on the remote control unit.
Purpose: To adjust the beam current of R, G, B, and
screen voltage.
Symptom of Misadjustment: White color may be
reddish, greenish or bluish.
13. H. Size Adjustment
Purpose: To obtain correct horizontal size of screen
image.
Symptom of Misadjustment: If H. Size is incorrect,
horizontal size of image on the screen may not be
properly displayed.
Test Point
Adj. Point
Mode
Input
---
VR562
RF
Monoscope
Tape
M. EQ.
Spec.
---
Monoscope
90±5%
Test Point
Adj. Point
Mode
Input
---
Screen-Control
CH o / p
buttons
RF
Black
Raster
Tape
M. EQ.
Spec.
---
Pattern
Generator
See Reference
Notes below.
Figure
PATTERN GENERATOR
Note: Use service remote control unit
1.
Operate the unit for at least 20 minutes.
2.
Receive the Monoscope Pattern.
3.
Adjust VR562 so that the monoscope pattern will
be 90±5% of display size and circle is round.
4.
Turn the Power off and on again. (Main power button on the TV unit.)
EXT. INPUT
Note: Screen Control FBT --- Main CBA
F.B.T= Fly Back Transformer
Use service remote control unit
1. Degauss the CRT and allow CRT to operate for 20
minutes before starting the alignment.
2. Input the Black Raster Signal from RF Input.
3. Enter the Service mode. (See page 5-1)
4. Press "VOL p" button on the service remote control unit and select "C/D" mode. (Display changes
"C/D," "7F," "LANGUAGE," "ACCESS CODE,"
"SOUND TYPE," "VIDEO TONE," "FM MODE,"
"V-OUT," "VIDEO," "AV MEMO," "STABLE
SOUND," "FILTER," "500," and "YUV MEMORY"
cyclically when "VOL p button is pressed.) then
press "1." The display will momentarily show "CUT
OFF R" (R= Red). Now there should be a horizontal line across the center of the picture tube. If
needed gradually turn the screen control on the flyback, clockwise until the horizontal line appears.
Adjust the Red Cut off by pressing the "CH o/p"
buttons. Proceed to Step 5 when the Red Cut off
adjustment is done.
5. Press the "2" button. The display will momentarily
show "CUT OFF G" (G=Green). Adjust the Green
Cut off by pressing the "CH o/p" buttons. Proceed
to step 6 when the Green Cut off adjustment is done.
6. Press the "3" button. The display will momentarily
show "CUT OFF B" (B=Blue). Adjust the Blue cut
off by pressing the "CH o/p" buttons. When done
with steps 4, 5 and 6 the horizontal line should be
pure white if not, then attempt the Cut off adjustment again.
14. PIN Cushion Adjustment
Purpose: To obtain correct straight vertical line of
screen image.
Symptom of Misadjustment: If H.Pin cushion is incorrect, vertical line of image on the screen may not be
properly displayed.
Test Point
Adj. Point
Mode
Input
---
VR561
RF
Cross
hatch
Tape
M. EQ.
---
Cross hatch
Spec.
Note: Use service remote control unit
1.
Operate the unit for at least 20 minutes.
2.
Receive the Cross hatch Pattern.
3.
Adjust VR561 so that the cross hatch pattern will
be straight line of display.
4.
Turn the Power off and on again. (Main power button on the TV unit.)
Fig. 2
5-5
L6610EA
16. White Balance Adjustment
17. Sub-Brightness Adjustment
Purpose: To mix red, green and blue beams correctly
for pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
Purpose: To get proper brightness.
Symptom of Misadjustment: If Sub-Brightness is
incorrect, proper brightness cannot be obtained by
adjusting the Brightness Control.
Test Point
Screen
Adj. Point
CH o / p
buttons
Mode
Input
RF
White
Raster
(APL
100%)
Tape
M. EQ.
Spec.
---
Pattern
Generator,
Color analyzer
See below
Test Point
Adj. Point
Mode
Input
---
CH o / p
buttons
RF
IQW
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
Figure
Figure
White
Black
This bar
just
visible
Fig. 4
Color Analyzer
Note: IQW Setup level --- 7.5 IRE
Use service remote control unit
1. Enter the Service mode. (See page 5-1)
Then input IQW signal from RF Input.
2. Press "MENU" button on the service remote control
unit and Select "BRT" mode. (Display changes
"BRT," "CNT," "CLR," "S-CLR," "C-CLR," "TNT," "VTNT," "S-TNT," "C-TNT," "SHARP," "S-SRP," and
"C-SRP" cyclically when "MENU" button is pressed).
Press "CH o/p" buttons so that the bar is just visible
(See above figure).
3. Turn the power off and on again. (Main power button on the TV unit.)
Fig. 3
Note: Use service remote control unit
1. Operate the unit more than 20 minutes.
2. Face the unit to east. Degauss the CRT using Degaussing Coil.
3. Input the White Raster (APL 100%).
4. Set the color analyzer to the CHROMA mode and
after zero point calibration, bring the optical receptor to the center on the tube surface (CRT).
5. Enter the Service mode. Press "VOL p" button on the
service remote control unit and select "C/D" mode.
(Display changes "C/D," "7F," "LANGUAGE," "ACCESS CODE," "SOUND TYPE," "VIDEO TONE,"
"FM MODE," "V-OUT," "VIDEO," "AV MEMO,"
"STABLE SOUND," "FILTER," "500," and "YUV
MEMORY" cyclically when "VOL p" button is
pressed.) then Press No. 8 button on the service remote control Unit.
6. Press No. 4 button on the service remote control
unit for Red adjustment. Press N0. 5 button on the
service remote control unit for Blue adjustment.
7. In each color mode, Press "CH o/p" button to adjust
the values of color.
8. Adjusting Red and Blue color so that the temperature
becomes 9200K (x: 286 / y: 294)±3%.
9. At this time, Re-check that Horizontal line is white.
If not, Re-adjust Cut-off Adjustment until the Horizontal Line becomes pure white.
10. Turn off and on again to return to normal mode. Receive APL 100% white signal and Check Chroma
temperatures become 9200K (x: 286 / y: 294)±3%.
Note: Confirm that Cut Off Adj. is correct after this
adjustment, and attempt Cut Off Adj. if needed.
18. Focus Adjustment
Purpose: Set the optimum Focus.
Symptom of Misadjustment: If Focus Adjustment is
incorrect, blurred images are shown on the display.
Test Point
Adj. Point
Mode
Input
---
Focus Control
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
Note: Focus VR (FBT) - Main CBA,
FBT=Fly Back Transformer
1. Operate the unit more than 30 minutes.
2. Face the unit to the East and Degauss the CRT
using Degaussing Coil.
3. Input the Monoscope Pattern.
4. Adjust the Focus Control on the FBT to obtain
clear picture.
5-6
L6610EA
21. Convergence Adjustment
The following adjustments normally are not
attempted in the field. Only when replacing the
CRT then adjust as a preparation.
Purpose: To obtain proper convergence of red, green
and blue beams.
Symptom of Misadjustment: If Convergence Adjustment is incorrect, the edge of white letters may have
color edges.
19. Purity Adjustment
Purpose: To obtain pure color.
Symptom of Misadjustment: If Color Purity Adjustment is incorrect, large areas of color may not be
properly displayed.
Test Point
Adj. Point
Mode
Input
---
Deflection
Yoke Purity
Magnet
---
Red
Color
Tape
M. EQ.
---
Pattern
Generator
Test Point
Adj. Point
Mode
Input
---
C.P. Magnet
(RB),
C.P. Magnet
(RB-G),
Deflection Yoke
---
Dot Pattern
or
Crosshatch
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below.
Spec.
See below.
Figures
Figure
22mm
GREEN
RED
BLUE
Fig. 5
Deflection Yoke
1. Set the unit facing east.
2. Operate the unit for over 30 minutes before adjusting.
3. Fully degauss the unit using an external degaussing coil.
4. Loosen the screw on the Deflection Yoke Clamper
and pull the Deflection Yoke back away from the
screen. (See Fig. 6)
5. Loosen the Ring Lock and adjust the Purity Magnets so that a red field is obtained at the center of
the screen. Tighten Ring Lock. (See Fig. 5,6)
6. Slowly push the Deflection Yoke toward bell of
CRT and set it where a uniform red field is obtained.
7. Tighten the clamp screw on the Deflection Yoke.
2.
Fig. 6
C.P. MAGNET (RB)
R
R
G
G
B
Fig. 7
B
C.B. MAGNET (RB-G)
RB
RB
G
G
Fig. 8
1. Loosen the Ring Lock and align red with blue dots
or Crosshatch at the center of the screen by rotating (RB) C.P. Magnets. (See Fig. 7)
2. Align red / blue with green dots at the center of the
screen by rotating (RB-G) C.P. Magnet. (See Fig. 8)
3. Paintlock the C.P. Magnets after adjustment.
4. Remove the DY Wedges and slightly tilt the Deflection Yoke horizontally and vertically to obtain
the best overall convergence.
5. Fix the Deflection Yoke by carefully inserting the
DY Wedges between CRT and Deflection Yoke.
20. VRS Adjustment
1.
6-polar convergence magnet
4-polar convergence magnet
VRS magnet
Purity magnet
Connect Oscilloscope and get the cross hatch pattern.
Adjust the two magnets for VRS adjustment like
the below figure so that the cross hatch pattern becomes flat.
5-7
L6610EA
22. Yh, Yv, Xv Adjustment
1.
Adjust the volume of Deflection Yoke(Yh, Yv, Xv)
to get good convergence.
FRONT
YH
Yv
Xv
Xv
YH
Yv
5-8
L6610EA
BLOCK DIAGRAMS
System Control Block Diagram
IC333
TV MICON/VIDEO
/AUDIO/CHROMA
/DEFLECTION
RCV101
(NO CONNECTION)
I2C-OPEN
SDA
SCL
CN301
3
5
6
RCV-IN 70
REMOTE
SENSOR
KEY-IN1 66
KEY-IN2 69
KEY
SWITCH
CN301 is used for
adjustment at factory
INPUT0
IC151
(MEMORY)
CS 7
SCL 6
SDA 5
FROM/TO
AUDIO BLOCK
SCL
SDA
FROM
IF/VIDEO BLOCK
AFT
AGC
TO
IF/VIDEO BLOCK
72 I2C-OPEN
58 SCL
56 SDA
INPUT0 63
73 AFT
75 AGC
INPUT1 80
Q141
Q131
INPUT0
INPUT1
A-O-MUTE
VOLUME
A-MUTE-H
A-O-MUTE 55
VOLUME 62
A-MUTE-H 64
DG-ON-H
+5V CTRL
+5V CTRL2
+8V CTRL
P-ON-H
PROTECT-1
PROTECT-2
PROTECT-3
DG-ON-H
+5V CTRL
+5V CTRL2
+8V CTRL
PROTECT-1
PROTECT-2
P-ON-H
PROTECT-1
PROTECT-2
PROTECT-3
P-ON-H
74
28
18
40
79
68
67
76
TO
AUDIO BLOCK
FROM/TO
POWER
SUPPLY BLOCK
FROM/TO
CRT/H.V. BLOCK
MAIN CBA
6-1
6-2
L6610BLS
IF/Video Block Diagram
RF/IF SIGNAL
TU1
VIDEO SIGNAL
IC33
SF1
SAW
FILTER
IF 11
20
21
AUDIO SIGNAL
(IF SIGNAL PROCESS)
VIF
AMP
WF1
CF31
VIDEO
DET
4.5MHz
TRAP
5
MAIN CBA
3
EQ
AMP
1
8
SIF
AMP
10
CF32
AGC
SCL
SDA
EXT.CLK
1
4
5
8
VCO
17
WF16
4.5MHz
FILTER
VCO F/B
LPF
RF
AGC
SIF
7
TO
AUDIO BLOCK
Q33
IF AGC DET
AFT
INPUT0
AMP
AGC
AFT
22
16
FROM/TO
SYSTEM
CONTROL
BLOCK
14
IC333
TV MICON/VIDEO
/AUDIO/CHROMA
/DEFLECTION
JK721
VIDEO-IN
(FRONT)
JK701
VIDEO-IN
(REAR)
Q21
WF2
11
14
58 SCL
56 SDA
32
VCXO
16
X301
3.58MHz
27
26
24
JK741
VIDEO-Y-IN
(REAR)
JK741
VIDEO-Cb-IN
(REAR)
JK741
VIDEO-Cr-IN
(REAR)
20
LUMINANCE
PROCESS
CIRCUIT
25
LPF
21
OSD SW
CONTRAST
BRIGHTNESS
RGB DRIVE
/CUT OFF
/H.V. BLK
52
51
50
WH301A
5 BLUE
4 GREEN
3 RED
TO
CRT/H.V. BLOCK
WH301B
29
CHROMA COMB
BASEBAND TINT
Q951
30
JK711
S-VIDEO-IN
C
CHROMINANCE
PROCESS
CIRCUIT
RGB MATRIX
/COLOR CONT
Y
OSD
H-SYNC
PROCESS
CIRCUIT
Q956
61 S-SW
6-3
53
46
45
38
37
V-SYNC
PROCESS
CIRCUIT
6-4
ACL
H-DRIVE
FBP
RAMP-OUT
V-RAMP-F/B
FROM/TO
CRT/H.V. BLOCK
L6610BLIF
Audio Block Diagram
AUDIO SIGNAL
IC431 (MTS/SAP AUDIO SIGNAL PROCESS)
MAIN CBA
FROM
IF/VIDEO BLOCK
SIF
21
VCA
STEREO
FILTER
SAP
FILTER
24
27
OFFSET
CANCEL
SAP
DEMOD
L+R
FILTER
75uS
DE-EMPH
L-CH
OFFSET
CANCEL
MATRIX
L-R
FILTER
(L-R)/SAP
SW
SAP OUT
FILTER
I2C
DECORDER
WIDE BAND
FILTER
WIDE BAND
RMS DET
dBX
DE-EMPH
SPECTRAL
EXPAND
SPECTRAL
FILTER
SPECTRAL
RMS DET
WIDE BAND
EXPAND
30
AGC
R-CH
OFFSET
CANCEL
29
IC771 (INPUT SELECT)
11
15
14
12
JK701
AUDIO-IN(L)
(REAR1)
IC801 (AUDIO AMP)
WF6
TUNER
REAR2
REAR1
FRONT
13
5
DC
VOL.
7
CN801
SP-L 1
SP-GND 2
SP801
SPEAKER
L-CH
2
DC
VOL.
12
CN802
SP-R 1
SP-GND 2
SP802
SPEAKER
R-CH
(L-CH)
JK701
AUDIO-IN(R)
(REAR1)
(R-CH)
JK702
AUDIO-IN(L)
(REAR2)
REAR1
5
TUNER
4
REAR2
2
FRONT
1
JK703
AUDIO-IN(R)
(REAR2)
3
6
SW CTL
JK722
AUDIO-IN(L)
(FRONT)
9
10
Q825
JK723
AUDIO-IN(R)
(FRONT)
Q761
AMP
JK702
AUDIO-OUT(L)
(REAR)
JK703
AUDIO-OUT(R)
(REAR)
Q751
AMP
Q792
Q791
Q793
6-5
Q794
+8V
A-MUTE-H
VOLUME
A-O-MUTE
FROM/TO
INPUT 0
SYSTEM CONTROL
INPUT 1
BLOCK
SCL
SDA
6-6
L6610BLA
CRT/H.V. Block Diagram
VIDEO SIGNAL
IC551 (V-DEFLECTION CONTROL)
MAIN CBA
RAMP-OUT
AMP
Q531
(SWITCHING)
V-RAMP-F/B
FROM/TO
IF/VIDEO BLOCK
FROM POWER
SUPPLY BLOCK
L551 D.Y.
5
7
P-ON-H
WF7
Q572
H.DRIVE
WF8
T572
1
PULSE
UP
3
Q533
SWITCHING
P-ON-ON
Q571
H.OUTPUT
4
5
6
H-DRIVE
PROTECT-1
PROTECT-2
WF12
THERMAL
PROTECTION
WF11
3
WF9
Q551, H.
Q552 CONTROL
1
VDRIVE
HDRIVE
CN551
Q561
(SWITCHING)
VR561
PCC
Q547
(SWITCHING)
VR562
WIDTH
DEF+B
+B
T571 F.B.T.
FOCUS VR
ANODE
HV
F
S
X-RAY CHECK
TP591
TP592
1
FOCUS
SCREEN
11
8
3
10
5
7
4
ANODE
SCREEN VR
9
6
TP302
15kHz
FROM/TO
SYSTEM CONTROL
BLOCK
WF10 WH501A
3 HEATER
1 +200V
PROTECT-3
FBP
ACL
WH501B
3
1
JK1501
FROM
IF/VIDEO BLOCK
WF3
TO WH301A WH301B
RED 3
GREEN 4
BLUE 5
Q1511,
Q1512
RED AMP
WF15
WF4
Q1521,
Q1522
WF14
GREEN AMP
TP500
GND
WF5
TP501
BLUE
BLUE AMP
Q1531,
Q1532
WF13
7
4
8
6
11
10
9
CN1501
FOCUS
SCREEN
GND
R
G
B
V501
CRT
HEATER
GND
CRT CBA
6-7
6-8
L6610BLCRT
Power Supply Block Diagram
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,
REPLACE ONLY WITH SAME TYPE 4 A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE 4A, 125V.
NOTE :
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
HOT CIRCUIT. BE CAREFUL.
HOT
COLD
T601
DEF +B
4A/125V
F601
4A/125V
AC601
AC CORD
L601
TP601
+B
D605 - D608
LINE
FILTER
BRIDGE
RECTIFIER
9
6
AL+33V
CN691
L691
DEGAUSSING
COIL
PROTECT-2
(TO PIN 67 OF IC333)
+B
Q111
+5V
SWITCHING
Q672
SWITCHING
10
PS691
4
Q851
+9V
REGULATOR
11
Q961
+5V
REGULATOR
Q673
SWITCHING
CONTROL
12
Q321
+9V
SWITCHING
BACK-UP
P-ON+5V
+5V CTRL2
(FROM PIN 18 OF IC333)
AL+9V
AL+12V
P-ON+5V
Q601
SWITCHING
2
Q681
14
+8V
SWITCHING
P-ON+8V
+8V CTRL
(FROM PIN40 OF IC333)
Q602
LIMITER
1
Q682
+5V
SWITCHING
13
P-ON+5V
+5V CTRL
(FROM PIN28 OF IC333)
Q683
+5V
SWITCHING
4
1
IC601
ERROR
VOLTAGE DET
VR661
3
2
+B ADJ
Q652
FEED
BACK
PROTECT-1
(TO PIN68 OF IC333)
Q831
SWITCHING
P-ON-ON
RL601
Q191
SWITCHING
P-ON-ON
Q674
SWITCHING
P-ON-ON
Q696
SWITCHING
DG-ON-ON
6-9
P-ON+12V
Q841
(SWITCHING)
DG-ON-H
(FROM PIN74 OF IC333)
P-ON-H
(FROM PIN79 OF IC333)
Q832
SWITCHING
P-ON-ON
MAIN CBA
6-10
L6610BLP
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS
Standard Notes
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often
pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are
identified in this manual and its supplements; electrical components having such features are identified by the
mark " # " in the schematic diagram and the parts list. Before replacing any of these components, read the parts
list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Note:
1.
Do not use the part number shown on these drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since these drawings were prepared.
2.
All resistance values are indicated in ohms (K=103, M=106).
3.
Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4.
All capacitance values are indicated in µF (P=10-6µF).
5.
All voltages are DC voltages unless otherwise specified.
Note of Capacitors:
ML --- Mylar Cap.
PP --- Metallized Film Cap.
SC --- Semiconductor Cap.
L --- Low Leakage type
Temperature Characteristics of Capacitors are noted with the following:
B --- ±10%
CH --- 0±60ppm/°C
CSL --- +350~-1000ppm/°C
Tolerance of Capacitors are noted with the following:
Z --- +80~-20%
Note of Resistors:
CEM --- Cement Res.
MTL --- Metal Res.
F --- Fuse Res.
Capacitors and transistors are represented by the following symbols.
CBA Symbols
Schematic Diagram Symbols
(Top View) (Bottom View)
+
Electrolytic Capacitor
Digital Transistor
(Bottom View)
Transistor or Digital Transistor
E
C
B
(Top View)
(Top View)
PNP Transistor
NPN Transistor
ECB
ECB
(Top View)
(Top View)
PNP Digital Transistor
NPN Digital Transistor
ECB
ECB
7-1
L13SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective
before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:
(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
(2) To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Wire Connectors
(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).
(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).
5. Note: Mark "I" is a leadless (chip) component.
6. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
1
5.0
(3.0)
Voltage
2
3
Power on mode
Power off mode
5.0
(3.0)
Unit: Volts
Indicates that the voltage
is not consistent here.
7. How to read converged lines
1-D3
Distinction Area
Line Number
(1 to 3 digits)
3
1-B1
AREA D3
Examples:
1. "1-D3" means that line number "1" goes to area "D3".
2. "1-B1" means that line number "1" goes to area "B1".
AREA B1
2
1-D3
1
A
B
C
D
8. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
7-2
L13SC
Main 1/4 Schematic Diagram
VIDEO SIGNAL
A4
B4
C4
D4
E4
F4
MAIN 1/4
Ref No.
Position
ICS
A3
B3
C3
D3
E3
F3
A2
B2
C2
D2
E2
F2
A1
B1
C1
D1
E1
F1
7-3
7-4
A-3
IC151
C-2
IC333
TRANSISTORS
Q111
D-1
Q131
A-3
Q141
A-4
Q191
B-4
Q321
E-1
CONNECTOR
CN301
A-3
L6610SCM1
Main 2/4 Schematic Diagram
VIDEO SIGNAL
AUDIO SIGNAL
G4
H4
I4
J4
K4
L4
MAIN 2/4
Ref No.
Position
ICS
G3
H3
I3
J3
K3
L3
G2
H2
I2
J2
K2
L2
G1
H1
I1
J1
K1
L1
7-5
7-6
G-3
IC431
H-2
IC771
J-4
IC801
TRANSISTORS
K-1
Q702
K-2
Q751
J-2
Q761
Q791
K-1
Q792
K-2
Q793
J-1
Q794
I-1
Q825
J-3
Q831
K-3
Q832
K-3
Q841
K-3
Q851
J-3
G-1
Q951
G-1
Q956
J-3
Q961
CONNECTORS
CN801
L-4
CN802
L-3
L6610SCM2
Main 3/4 Schematic Diagram
IF SIGNAL
VIDEO SIGNAL
AUDIO SIGNAL
M4
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
N4
O4
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
P4
4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE
MÊME TYPE DE 4A, 125V.
Q4
R4
MAIN 3/4
Ref No.
Position
ICS
M3
N3
O3
P3
Q3
R3
M2
N2
O2
P2
Q2
R2
M1
N1
O1
P1
Q1
R1
7-7
7-8
P-3
IC33
O-1
IC601
TRANSISTORS
Q21
P-4
P-4
Q33
P-2
Q601
P-1
Q602
O-1
Q652
N-2
Q672
N-1
Q673
N-1
Q674
M-2
Q681
M-1
Q682
M-1
Q683
O-2
Q696
CONNECTOR
CN691
Q-2
TEST POINTS
N-4
TP300
N-4
TP301
VARIABLE RESISTOR
VR661
O-1
L6610SCM3
Main 4/4 & CRT Schematic Diagram
MAIN 4/4
Ref No.
Position
IC
S-3
IC551
TRANSISTORS
S-2
Q531
S-2
Q533
U-2
Q547
Q551
T-3
T-3
Q552
Q561
U-3
Ref No.
Position
TRANSISTORS
U-2
Q571
T-2
Q572
CONNECTORS
T-3
CN571
WH301A
V-2
WH501A
V-3
TEST POINTS
TP302
V-2
CRT
Ref No.
Position
TRANSISTORS
W-1
Q1511
W-2
Q1512
W-1
Q1521
W-2
Q1522
W-1
Q1531
W-2
Q1532
CONNECTORS
CN1501
X-2
WH301B
V-2
WH501B
V-3
TEST POINTS
W-1
TP500
TP501
W-2
Ref No.
Position
TEST POINTS
U-2
TP591
TP592
U-2
U-2
TP601
VARIABLE RESISTORS
VR561
U-3
VR562
U-3
VIDEO SIGNAL
S3
T3
U3
V3
W3
X3
S2
T2
U2
V2
W2
X2
S1
T1
U1
V1
W1
X1
7-9
7-10
L6610SCM4
Main CBA Top View
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power
supply circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER
SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.
ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT
SLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLY
CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.
4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE
MÊME TYPE DE 4A, 125V.
MAIN CBA
Ref No.
Position
ICS
B-2
IC33
E-5
IC151
F-5
IC333
A-1
IC431
C-2
IC551
C-4
IC601
D-1
IC771
IC801
E-2
TRANSISTORS
Q21
C-1
C-1
Q33
Q111
F-3
Q131
F-4
Q141
E-5
Q191
F-5
Q321
E-3
Q531
C-2
Q533
C-2
Q547
B-2
B-2
Q551
B-2
Q552
B-2
Q561
B-4
Q571
C-2
Q572
B-1
Q601
B-4
Q602
D-4
Q652
D-3
Q672
D-3
Q673
D-3
Q674
D-3
Q681
D-4
Q682
D-4
Q683
Q696
D-4
TP601
+B
FOCUS-VR
(UPPER SIDE)
SCREEN-VR
(LOWER SIDE)
TP300
GND
TP302
15kHz
Ref No.
Position
TRANSISTORS
D-2
Q702
C-1
Q751
C-1
Q761
C-1
Q791
C-1
Q792
D-1
Q793
D-1
Q794
E-2
Q825
E-3
Q831
F-3
Q832
F-2
Q841
E-3
Q851
Q951
D-1
Q956
D-1
Q961
C-1
CONNECTORS
A-1
CN301
B-3
CN571
D-5
CN691
E-2
CN801
E-5
CN802
WH301A
D-4
WH501A
A-4
TEST POINTS
A-4
TP300
A-2
TP301
TP302
A-4
TP591
A-3
TP592
A-3
B-5
TP601
VARIABLE RESISTORS
B-2
VR561
B-2
VR562
VR661
B-2
VR661
+B ADJ
VR561
PCC
VR562
WIDTH
TP301
AGC
7-11
7-12
BL6650F01011-1
Main CBA Bottom View
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE
MÊME TYPE DE 4A, 125V.
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER
SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.
ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT
SLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLY
CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.
WF8
Q571
Base
WF10
PIN 3
OF WH501A
WF2
PIN 14
OF IC333
WF9
PIN 1
OF CN571
WF12
PIN 4
OF CN571
WF11
PIN 7
OF IC551
WF7
Q572
Collector
WF16
PIN 8
OF TU1
WF1
PIN 3
OF IC33
WF6
PIN 5
OF IC801
7-13
7-14
BL6650F01011-1
CRT CBA Top View
CRT CBA Bottom View
CRT CBA
Ref No.
Position
TRANSISTORS
Q1511
C-1
Q1512
C-1
C-1
Q1521
C-1
Q1522
B-1
Q1531
B-1
Q1532
CONNECTORS
CN1501
A-2
WH301B
B-2
WH501B
A-2
TEST POINTS
TP500
B-2
TP501
B-2
WF15
Q1511
Collector
TP501
BLUE
7-15
WF3
Q1511
Base
WF4
Q1521
Base
WF14
Q1521
Collector
WF5
Q1531
Base
WF13
Q1531
Collector
TP500
GND
7-16
BL6650F01011-2
WAVEFORMS
Input:
NTSC Color Bar Signal (with 1kHz Audio Signal)
INITIAL POSITION: Unplug unit from AC outlet for at least 5 minutes.
reconnect to AC outlet and then turn power on.
(Brightness---Center Color---Center Tint --- Center Contrast---Approx 70%)
WF1 ~ WF16 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
GND
GND
GND
WF1
1DIV: 0.5V 20µsec
IC 33 Pin 3
WF5
1DIV: 2V 20µsec
Q 1531 Base
WF9
1DIV: 200V 20µsec
CN 571 Pin 1
WF13 1DIV: 20V 20µsec
Q 1531 Collector
GND
WF2
1DIV: 0.5V 20µsec
IC 333 Pin 14
WF6
1DIV: 0.2V 20msec
IC 801 Pin 5
GND
WF3
WF14 1DIV: 20V 20µsec
Q 1521 Collector
WF11 1DIV: 2V 5msec
IC 551 Pin 7
WF15 1DIV: 20V 20µsec
Q 1511 Collector
GND
WF7
1DIV: 2V 20µsec
Q 1511 Base
WF10 1DIV: 5V 20µsec
WH501A Pin 3
1DIV: 10V 20µsec
Q 572 Collector
GND
10 V
WF4
WF8
1DIV: 2V 20µsec
Q 1521 Base
8-1
1DIV: 5V 20µsec
Q 571 Base
5 ms
WF12 1DIV: 10V 5msec
CN 571 Pin 4
WF16 1DIV: 0.2V 20µsec
TU 1 Pin 8
8-2
L6650WF
WIRING DIAGRAM
CLN801
SP801
SPEAKER
L-CH
CLN802
SP802
SPEAKER
R-CH
CN801
1 SP-L
2 SP-GND
CN802
1 SP-R
2 SP-GND
ANODE
TU1 TUNER UNIT
V501
CRT
MAIN CBA
BL6650F01011-1
CN691
1
2
GND
CN1501
FOCUS
T571
FBT
SCREEN
WH301B
BLUE
GREEN
RED
GND
+8V
CRT CBA
BL6650F01011-2
5
4
3
2
1
WH501B
HEATER 3
GND 2
+200V 1
CLN301
CLN501
L551
D.Y.
HD
VD
5
4
3
2
1
WH301A
BLUE
GREEN
RED
GND
+8V
WH501A
3 HEATER
2 GND
1 +200V
CN571
1
2
3
4
5
(NO CONNECTION)
CN301
1 INT-MONI
2 AGC
3 I2C-OPEN
4 GND
5 SDA
6 SCL
CN301 IS USED FOR
ADJUSTMENT AT
FACTORY.
AC601
9-1
L6610WI
IC PIN FUNCTIONS
IC333 (TV Micro Computer)
Pin
No.
Signal Name
Pin
No.
Function
Signal Name
Function
35 N.U.
Not Used
1
GND
GND
36 N.U.
Not Used
2
N.U.
Not Used
37 V RAMP F/B
V Ramp Feed Back
3
N.U.
Not Used
38 V RAMP OUT
Vertical Output
4
N.U.
Not Used
39 V RAMP CAP
V Ramp OSC Capacitor
5
GND
GND
40 8.7 VREG OUT
DC 8.7V Output
6
VCC
AL+5V
41 N.U.
Not Used
7
N.U.
Not Used
42 H VCO F/B
H Vco Feed Back
8
FILT
FILT
43 AFC FILT
Horizontal AFC Filter
9
HLF
Filter for CCD
44 GND
GND
10 VHOLD
VHOLD
45 FBP IN
Flyback Pulse Input
11 CVIN
Input for Video Signal
46 H-OUT
H Pulse Output
12 RESET
RESET
47 VCC
Vcc
48 VCC
Vcc
49 VCC
Vcc
13
MCU RESET
OUT
RESET Signal Output
14 Y-SW OUT
Composite Signal Output
50 R OUT
Red Output
15 GND
GND
51 G OUT
Green Output
16 3.58 X'TAL
3.58MHz Crystal
52 B OUT
Blue Output
17 C-APC
CHROMINANCE APC
53 ACL
IB-Input
Micro controller Control
Voltage Output
54 N.U.
Not Used
55 A-O-MUTE
Mute Signal of Audio Output
56 SDA
I2C-BUS Controller Interface
(Data)
57 N.U.
Not Used
58 SCL
I2C-BUS Controller Interface
(Clock)
18
MCU 5.7REG
OUT
19 N.U.
Not Used
20 CVBS IN 3
Composite Signal Input 3
21 N.U.
Not Used
22 VCC
VCC
23 N.U.
(GND)
24 CVBS IN2
Composite Signal Input 2
59 N.U.
(GND)
25 N.U.
Not Used
60 N.U.
Not Used
26 CVBS IN1
Composite Signal Input 1
61 S-SW
27 N.U.
Not Used
Detecting S-VIDEO Jack
Connection
28 5.7V REG OUT
5.7V Output
62 VOLUME
Volume
29 C(Y/C) IN
Chrominance Signal Input
63 INPUTO
Input Select 0
30 Y(Y/C) IN
Luminance Signal Input
64 A-MUTE-H
Audio Mute
31 V REG VCC
DC 8.7V Input
65 N.U.
Not Used
32 FSC OUT
Clock Output 3.58MHz
66 KEY-IN 1
Key Input 1 (Main)
33 MONITOR OUT
Monitor Out
67 PROTECT-2
Power Supply Protection
34 N.U.
Not Used
68 PROTECT-1
Power Supply Protection
69 KEY-IN 2
Key Input 2 (Main)
10-1
L6650PIN
Pin
No.
Signal Name
Function
70 RCV-IN
Input For Remote Control
71 N.U.
Not Used
72 I2C OPEN
White Balance Adjustment
Judgement
73 AFT
AFT Voltage Input
74 DG-ON-H
Degaussing Coil Control
75 AGC
AGC Voltage Input
76 PROTECT 3
Power Supply Protection
77 N.U.
Not Used
78 FM-SW
Switching IF IC VCO
79 P-ON-H
Output for P-ON-H
80 INPUT 1
Input Select 1
10-2
L6650PIN
EXPLODED VIEWS
L-8
Cabinet
L-8
SHINWHA
TAPE SGT-730
(BLACK)
A-4
V501-1
Details for DY551 (L551)
and surrounding parts
V501-2
SHINWHA
TAPE SGT-730
(WHITE)
L-8
L-10
B-11
DY551
(L551)
L-9
Scotch Tape #880
B-20
B-2
CLN551
L-8
DY551 (L551)
B-2
L-8
B-2
CRT CBA
B-1
B-11
B-20
L-8
L691
A-2
B-20
L-1
B-8
L-1
B-7
L-1
B-6
L-13
SP801
B-2
L-1
V501
L-13
L-1
B-9
PB1
L-13
SP802
B-20
PB6
B-12
L-13
MAIN CBA
PB6
A-5
AC601
A-3
A-1
11-1
11-2
L6610CEX
Packing
X-1
X-3
X-2
X-4
TAPE
S-2
S-6
X-5
S-4
S-1
S-3
PACKING TAPE
S-5
FR
ON
T
S7 (EWF2703 only)
PACKING TAPE
11-3
L6610PEX
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a #
have special characteristics important to safety. Before
replacing any of these components, read carefully the
product safety notice in this service manual. Don't
degrade the safety of the product through improper servicing.
NOTE:
Parts that are not assigned part numbers (---------) are
not available.
Comparison Chart of Models and Marks
Ref. No.
Model
Mark
6427FD
A
EWF2703
B
Description
Description
DRY BATTERY R6P UM3 or
Part No.
XB0M451GH001
DRY BATTERY R6P/2S or
XB0M451T0001
DRY BATTERY(SUNRISE) R6SSE/2S or
XB0M451MS002
DRY BATTERY R6P(AR)2PX or
XB0M451HU002
DRY BATTERY R6P(AR)2P X ICI
XB0M451HU003
X-3#
A
OWNER'S MANUAL L6610UA:JAPANESE 0EMN02197
X-3#
B
OWNER'S MANUAL L6616UG
X-4
A
RETURN STOP SHEET L6101UB
0EM407077
X-4
B
RETURN STOP SHEET T4259UK
0EM406203A
POLYETHYLENE BAG F8626B5
Z325350
X-5
0EMN02186
Note:
1. V501 (CRT) HAS COUPLE OF SUBSTITUTIONAL PARTS AND EACH PARTS
ALSO HAS MATCHING COMBINATION WITH DY551 (OR L551).
PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.
2. DY551 (OR L551) (DEFLECTION YOKE) HAS MATCHING COMBINATION WITH
V501.
PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.
CRT TYPE A
Part No.
A-1
A
FRONT CABINET L6610UA
0EM101327
A-1
B
FRONT CABINET L6616UG
0EM101324
A-2
Ref. No.
X-2
REAR CABINET L6616UG
0EM101302
CONTROL PLATE L6610UA
0EM301899
A-3
A
A-3
B
CONTROL PLATE L6616UG
0EM301889
A-4#
A
RATING LABEL L6610UA
----------
A-4#
B
RATING LABEL L6616UG
----------
A-5
A
BRAND BADGE L L1520UASYLVANIA
0EM406577
A-5
B
BRAND BADGE L TD351UBEMERSON
0EM407162
B-1
TENSION SPRING B0080B0:EM40808
26WH006
B-2
SCREW L1500UA
0EM406142
B-11
CLOTH 190X15XT0.5
TS7623
B-12
CLOTH 110X15XT2.0
0EM406734
B-13
CLOTH L1440JL:15X55XT1.0
0EM406793
B-20#
DEGAUSS HOLDER L1520UA
0EM406700
CLN551
CRT GND WIRE CRT GND WIRE
WX1L6615-001
L-8
SCREW, P-TIGHT 4X18 BIND HEAD +
GBMP4180
L-9
SCREW TAPPING M4X14
DBU14140
L-10
SCREW, P-TIGHT 3X10 BIND HEAD+
GBKP3100
L-13
SCREW, ASSEMBLED 12:M3X12
0EM406746
L691
DEGAUSSING COIL F-043
LLBH00ZTM043
PB1#
CHASSIS NO. LABEL L6616UG
----------
SP801
SPEAKER S08F38-B
DSD0808XQ015
SP802
SPEAKER S08F38-A
DSD0808XQ014
V501#
CRT A68QDL280X051(C)
V501-1
PCM JH88DTA
TCRT190QS028
XM04000BV010
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
CRT TYPE B
L551#
DEFLECTION YOKE KDY4UHD47X
LLBY00ZMS023
V501#
CRT M68LQK125X
TCRT190MS013
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
CRT TYPE C
L551#
DEFLECTION YOKE SCD-29119
LLBY00ZQS011
V501#
CRT A68QCP893X
TCRT190SM026
V501-1
PCM JH88DTA
XM04000BV010
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
CRT TYPE D
DY551#
DEFLECTION YOKE 6150Z-1247V
LLBY00ZGS009
V501#
CRT A68QCU759X
TCRT190GS044
V501-1
PCM JH88DTA
XM04000BV010
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
PACKING
S-1
A
CARTON L6610UA
0EM408280
S-1
B
CARTON L6616UG
0EM408254
S-2
STYROFOAM TOP ASSEMBLY L1520UA 0EM406512
S-3
STYROFOAM BOTTOM ASSEMBLY
L1520UA
0EM406513
S-4
SET SHEET PCEC:003502019816
0EM403887
S-5
A
SERIAL NO. LABEL L6610UA
----------
S-5
B
SERIAL NO. LABEL L6616UG
----------
HOLD PAD L1520UA
0EM406681
----------
S-6
S-7
B
LABEL, EAS(H3761UD) MAKER
NO.ZLLFNSLE1
X-1
A
REMOTE CONTROL NE122UD
NE122UD
X-1
B
REMOTE CONTROL NE116UD
NE116UD
ACCESSORIES
20030408
12-1
L6610CA
Table 1 (V501 and DY551 (OR L551) Combination)
Note 1: Purity and Convergence Adjustments must be
performed following CRT replacement. Refer to Electrical Adjustment Instructions.
Note 2: Please confirm CRT Type No. on the CRT
Warning Label which is located on the CRT. Then See
the Table 1 for V501 and DY551 (OR L551) combination chart.
Please refer this CRT, Deflection Yoke combination
chart for parts order.
V501: CRT Type No.
DY551 (OR L551):
V501: CRT Part No. Deflection Yoke Part
No.
A68QDL280X051(C)
TCRT190QS028
--------------------
M68LQK125X
TCRT190MS013
LLBY00ZMS023
A68QCP893X
TCRT190SM026
LLBY00ZQS011
A68QCU759X
TCRT190GS044
LLBY00ZGS009
CRT Warning Label Location
CRT Type No.
CRT Warning
Label
CRT
20030408
12-2
L6610CA
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read carefully the product safety notice in this service manual.
Don't degrade the safety of the product through
improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
Ref. No.
C49
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Ref. No.
MMA-414 CBA
Part No.
MAIN CBA
--------------
CRT CBA
--------------
MAIN CBA
Ref. No.
CCA1JKT0B102
CDA1EZT0F103
C53
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C54
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
C55
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
C57
C58
MAIN CBA
Consists of the following
Part No.
------------
CAPACITORS
C1
C2
C3
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
ELECTROLYTIC CAP. 4.7µF/50V M or
CE1JMASTL4R7
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
C4
CERAMIC CAP.(AX) F Z 0.01µF/50V
CA1J103TU014
C7
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
C30
PCB JUMPER D0.6-P5.0
JW5.0T
C31
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C32
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
C34
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
C35
CERAMIC CAP.(AX) CH J 56pF/50V
CA1J560TU008
C36
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
C37
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
C38
C41
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
20030408
C112
FILM CAP.(P) 0.047µF/50V J or
CMA1JJS00473
FILM CAP.(P) 0.047µF/50V J or
CA1J473MS029
FILM CAP.(P) 0.047µF/50V J TV or
CMB1JJS00473
MYLAR CAP. 0.047µF/50V K
2250473S
FILM CAP.(P) 0.033µF/50V J or
CMA1JJS00333
FILM CAP.(P) 0.033µF/50V J or
CA1J333MS029
FILM CAP.(P) 0.033µF/50V J TV
CMB1JJS00333
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
ELECTROLYTIC CAP. 47µF/16V M or
CE1CMASTL470
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
ELECTROLYTIC CAP. 4.7µF/50V M or
CE1JMASTL4R7
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
C113
CERAMIC CAP. F Z 0.1µF/25V
CDA1EZT0F104
C114
FILM CAP.(P) 0.001µF/50V J or
CMA1JJS00102
FILM CAP.(P) 0.001µF/50V J or
CA1J102MS029
FILM CAP.(P) 0.001µF/50V J TV or
CMB1JJS00102
C115
Description
CE1JMASDL4R7
CERAMIC CAP.(AX) F Z 0.01µF/25V
0ESA05480
Consists of the following
CE1JMASTL4R7
ELECTROLYTIC CAP. 4.7µF/50V M
CERAMIC CAP.(AX) B K 1000pF/50V
C111
Description
ELECTROLYTIC CAP. 4.7µF/50V M or
C52
C104
MMA-414 CBA
Part No.
CE1JMASDLR47
C51
F.....±1%
G.....±2%
Description
ELECTROLYTIC CAP. 0.47µF/50V M
MYLAR CAP. 0.001µF/50V K
2250102S
ELECTROLYTIC CAP. 0.1µF/50V M or
CE1JMASTLR10
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDLR10
C116
CERAMIC CAP.(AX) B K 220pF/50V
CCA1JKT0B221
C117
CERAMIC CAP.(AX) Y K 0.01µF/16V
CDA1CKT0Y103
C119
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
C120
C122
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C132
CERAMIC CAP. F Z 0.1µF/25V
CDA1EZT0F104
C133
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
C150
CERAMIC CAP. F Z 0.1µF/25V
CDA1EZT0F104
C151
CERAMIC CAP.(AX) B K 220pF/50V
CCA1JKT0B221
C152
CERAMIC CAP.(AX) B K 220pF/50V
CCA1JKT0B221
C301
CERAMIC CAP.(AX) CH J 120pF/50V
CA1J121TU008
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
C302
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
C303
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
C304
ELECTROLYTIC CAP. 0.1µF/50V M or
CE1JMASTLR10
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDLR10
C305
C306
C309
C321
13-1
ELECTROLYTIC CAP. 0.1µF/50V M or
CE1JMASTLR10
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDLR10
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
ELECTROLYTIC CAP. 0.1µF/50V M or
CE1JMASTLR10
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDLR10
ELECTROLYTIC CAP. 0.1µF/50V M or
CE1JMASTLR10
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDLR10
L6610EL
Ref. No.
C322
C323
C324
Description
Part No.
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
ELECTROLYTIC CAP. 0.47µF/50V M
ELECTROLYTIC CAP. 0.1µF/50V M or
ELECTROLYTIC CAP. 0.1µF/50V M
Ref. No.
Description
Part No.
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
CE1JMASDLR47
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
CE1JMASTLR10
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
CE1JMASDLR10
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C429
C441
C442
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C325
CERAMIC CAP.(AX) SL J 12pF/50V
CCA1JJTSL120
C328
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C329
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
C330
STACKED FILM CAP. 0.47µF/50V J
CMA1JJS00474
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
C331
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
C332
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
MYLAR CAP. 0.1µF/50V K
2250104S
C341
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
C342
ELECTROLYTIC CAP. 1µF/50V M or
C444
C445
C446
CMA1JJS00104
CA1J104MS029
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
MYLAR CAP. 0.1µF/50V K
2250104S
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
C448
ELECTROLYTIC CAP. 2.2µF/50V M or
CE1JMASTL2R2
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
C501
FILM CAP. 0.22µF/50V J or
122Z313S
CA1J103TU011
ELECTROLYTIC CAP. 2200µF/10V M or
CE1AMZNTL222
ELECTROLYTIC CAP. 2200µF/10V M
CE1AMZNDL222
ELECTROLYTIC CAP. 470µF/10V M or
CE1AMASTL471
C502
ELECTROLYTIC CAP. 470µF/10V M
CE1AMASDL471
C503
ELECTROLYTIC CAP. 470µF/10V M or
CE1AMASTL471
ELECTROLYTIC CAP. 470µF/10V M
CE1AMASDL471
C351
CERAMIC CAP.(AX) B K 100pF/50V
CCA1JKT0B101
C352
CERAMIC CAP.(AX) B K 100pF/50V
CCA1JKT0B101
C353
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
C402
C403
CE1JMASTLR33
CE1JMASDLR33
FILM CAP.(P) 0.1µF/50V J or
CERAMIC CAP.(AX) B K 0.01µF/50V
C401
ELECTROLYTIC CAP. 0.33µF/50V M or
ELECTROLYTIC CAP. 0.33µF/50V M
CE1JMASTL1R0
C343
C349
CE1JMASTL2R2
CE1JMASDL2R2
FILM CAP.(P) 0.1µF/50V J or
C345
C347
ELECTROLYTIC CAP. 2.2µF/50V M or
ELECTROLYTIC CAP. 2.2µF/50V M
C504
C505
C506
ELECTROLYTIC CAP. 3.3µF/50V M or
CE1JMASTL3R3
ELECTROLYTIC CAP. 3.3µF/50V M
CE1JMASDL3R3
C508
C520
ELECTROLYTIC CAP. 3.3µF/50V M or
CE1JMASTL3R3
ELECTROLYTIC CAP. 3.3µF/50V M
CE1JMASDL3R3
CERAMIC CAP.(AX) F Z 0.1µF/50V or
CA1J104TU014
CERAMIC CAP.(AX) F Z 0.1µF/50V
CCA1JZT0F104
C532
CT1J224MS045
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
ELECTROLYTIC CAP. 100µF/35V M or
CE1GMASTL101
ELECTROLYTIC CAP. 100µF/35V M
CE1GMASDL101
ELECTROLYTIC CAP. 1µF/50V M LL or
CE1JMASLL1R0
ELECTROLYTIC CAP. 1µF/50V LL
CE1JMASLH1R0
ELECTROLYTIC CAP. 1000µF/35V M or
CE1GMZNTL102
ELECTROLYTIC CAP. 1000µF/35V M or
CE1GMZNDL102
ELECTROLYTIC CAP. 1000µF/35V M
CE1GMZADL102
ELECTROLYTIC CAP. 1000µF/35V M or
CE1GMZNTL102
ELECTROLYTIC CAP. 1000µF/35V M or
CE1GMZNDL102
ELECTROLYTIC CAP. 1000µF/35V M
CE1GMZADL102
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C404
CERAMIC CAP.(AX) B K 0.022µF/50V
CA1J223TU011
C405
CERAMIC CAP. F Z 0.1µF/25V
CDA1EZT0F104
C406
CERAMIC CAP.(AX) B K 0.033µF/50V
CA1J333TU011
C411
ELECTROLYTIC CAP. 4.7µF/50V M or
CE1JMASTL4R7
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
CERAMIC CAP. B K 680pF/1KV
CA3A681MR028
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
C555
METALIZED PLYESTER CAP. 2.2µF/100V J
CT2A225MS065
C556
C413
C541
TF CAP. 0.22µF/50V J
C551
FILM CAP.(P) 0.082µF/50V J or
CMA1JJS00823
FILM CAP.(P) 0.082µF/50V J
CA1J823MS029
CERAMIC CAP. B K 680pF/1KV or
CCD3AKD0B681
CERAMIC CAP. B K 680pF/1KV or
CCD3AKP0B681
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
C414
ELECTROLYTIC CAP. 2.2µF/50V M or
CE1JMASTL2R2
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
C415
CERAMIC CAP.(AX) B K 150pF/50V
CCA1JKT0B151
MYLAR CAP. 0.1µF/50V K
2250104S
C416
CERAMIC CAP.(AX) B K 150pF/50V
CCA1JKT0B151
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASTL470
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASDL470
C417
C421
ELECTROLYTIC CAP. 2.2µF/50V M or
CE1JMASTL2R2
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
ELECTROLYTIC CAP. 4.7µF/50V M or
CE1JMASTL4R7
C561
C562
ELECTROLYTIC CAP. 470µF/10V M or
CE1AMASTL471
ELECTROLYTIC CAP. 470µF/10V M
CE1AMASDL471
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
C563#
P.P.CAP 0.39µF/200 J or
CA2D394VC012
C423
CERAMIC CAP.(AX) X K 4700pF/16V
CDA1CKT0X472
#
PP CAP. 0.39µF/250V J
CT2E394MS041
C424
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
C564#
P.P. CAP 0.33µF/200V J or
CA2D334VC012
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
#
PP CAP. 0.33µF/250V J
CT2E334MS041
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
C565
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
CMB1JJS00104
C426
C428
ELECTROLYTIC CAP. 4.7µF/50V M or
CE1JMASTL4R7
FILM CAP.(P) 0.1µF/50V J TV or
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
MYLAR CAP. 0.1µF/50V K
2250104S
CERAMIC CAP.(AX) X K 4700pF/16V
CDA1CKT0X472
PP CAP. 0.0022µF/1.6KV J or
CA3C222VC010
20030408
C567#
13-2
L6610EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
#
PP CAP. 0.0022µF/1.6KV J
CT3C222MS039
#
C568
FILM CAP.(P) 0.033µF/50V J or
CMA1JJS00333
C650
FILM CAP.(P) 0.033µF/50V J or
CA1J333MS029
FILM CAP.(P) 0.033µF/50V J TV
CMB1JJS00333
CERAMIC CAP. 560pF/2KV
CA3D561PAN04
P.P. CAP 0.68µF/200V J
CA2D684VC012
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
CE1JMASTL010
C571#
C654
CERAMIC CAP. 0.0047µF F CS
CCG2HMN0F472
CERAMIC CAP. LB 560pF/2KV or
CA3D561KG004
CERAMIC CAP. BN 560pF/2KV or
CCD3DKA0B561
C574#
ELECTROLYTIC CAP. 4.7µF/250V M or
CE2EMASTL4R7
ELECTROLYTIC CAP. 1µF/50V M or
#
ELECTROLYTIC CAP. 4.7µF/250V M
CE2EMASDL4R7
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
C577
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASTL470
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASDL470
C578
FILM CAP.(P) 0.01µF/50V J or
CMA1JJS00103
C656
ELECTROLYTIC CAP. 100µF/160V M W/F or
CE2CMZNTL101
ELECTROLYTIC CAP. 100µF/160V M
CE2CMZPDL101
FILM CAP.(P) 0.01µF/50V J or
CA1J103MS029
C657#
ELECTROLYTIC CAP. 2200µF/35V M or
CE1GMZNTL222
FILM CAP.(P) 0.01µF/50V J TV or
CMB1JJS00103
#
ELECTROLYTIC CAP. 2200µF/35V M
CE1GMZNDL222
CE1CMZNTL102
MYLAR CAP. 0.01µF/50V K
2250103S
C658#
ELECTROLYTIC CAP. 1000µF/16V M(VR/HC) or
C580#
PP CAP. 0.012µF/1.6KV J or
CA3C123VC010
#
ELECTROLYTIC CAP. 1000µF/16V M or
CE1CMZNDL102
#
PP CAP. 0.012µF/1.6KV J
CT3C123MS039
#
ELECTROLYTIC CAP. 1000µF/16V M
CE1CMZADL102
C582#
P.P. CAPACITOR 0.033µF/630V J or
CBP2KJD00333
C661
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
#
P.P. CAPACITOR 0.033µF/630V J or
CT2K333KF011
C662#
ELECTROLYTIC CAP. 1000µF/25V M or
CE1EMZNTL102
#
P.P. CAPACITOR 0.033µF/630V J
CBP2KKD00333
#
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZPDL102
C583#
FILM CAP.(P) 0.1µF/100V J or
CMA2AJS00104
C667
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
#
FILM CAP.(P) 0.1µF/100V J TV
CMB2AJS00104
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
C584#
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
#
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
C588#
ELECTROLYTIC CAP. 100µF/160V M W/F or
CE2CMZNTL101
#
ELECTROLYTIC CAP. 100µF/160V M
CE2CMZPDL101
C594#
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
#
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C596
CERAMIC CAP. B K 220pF/500V
CCD2JKS0B221
C601#
METALLIZED FILM CAP. 0.1µF/250V or
CT2E104MS037
#
METALLIZED FILM CAP. 0.1µF/275V K
CT2E104HJE06
#
FILM CAP.(MP) 0.1µF/250V K
CT2E104DC011
#
METALLIZED FILM CAP. 0.1µF/275V K
CT2E104HJE06
C603
CERAMIC CAP.(AX) B K 470pF/50V
CCA1JKT0B471
C605
C606
C609
C681
C682
C684
C685
C686
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
ELECTROLYTIC CAP. 470µF/10V M or
CE1AMASTL471
ELECTROLYTIC CAP. 470µF/10V M
CE1AMASDL471
ELECTROLYTIC CAP. 1000µF/10V M or
CE1AMASTL102
ELECTROLYTIC CAP. 1000µF/10V M
CE1AMASDL102
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
CCA1JKT0B101
CERAMIC CAP. F Z 0.01µF/500V or
CCD2JZP0F103
C701
CERAMIC CAP.(AX) B K 100pF/50V
CERAMIC CAP. 0.01µF/AC250V
CCD2EZA0F103
C702
PCB JUMPER D0.6-P5.0
JW5.0T
CERAMIC CAP. F Z 0.01µF/500V or
CCD2JZP0F103
C705
CERAMIC CAP.(AX) X K 6800pF/16V
CDA1CKT0X682
CERAMIC CAP. 0.01µF/AC250V
CCD2EZA0F103
C706
CERAMIC CAP. B K 680pF/2KV or
CCD3DKD0B681
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
CDA1CKT0X682
CERAMIC CAP. B K 680pF/2KV
CCD3DKP0B681
C708
CERAMIC CAP.(AX) X K 6800pF/16V
C610#
ELECTROLYTIC CAP. 470µF/200V M or
CE2DMZNTL471
C709
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
#
ELECTROLYTIC CAP. 470µF/200V M or
CE2DMZNDL471
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
#
ELECTROLYTIC CAP. 470µF/200V
CA2D471NC013
C611
FILM CAP.(P) 0.068µF/50V J or
CMA1JJS00683
C613
C713
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
FILM CAP.(P) 0.068µF/50V J or
CA1J683MS029
C718
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
FILM CAP.(P) 0.068µF/50V J TV or
CMB1JJS00683
C721
CERAMIC CAP.(AX) B K 100pF/50V
CCA1JKT0B101
MYLAR CAP. 0.068µF/50V K
2250683S
C722
FILM CAP.(P) 0.056µF/50V J or
CMA1JJS00563
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
CDA1CKT0X682
FILM CAP.(P) 0.056µF/50V J or
CA1J563MS029
C725
CERAMIC CAP.(AX) X K 6800pF/16V
FILM CAP.(P) 0.056µF/50V J TV or
CMB1JJS00563
C726
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
MYLAR CAP. 0.056µF/50V KT
2250563S
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
C614
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
C728
CERAMIC CAP.(AX) X K 6800pF/16V
CDA1CKT0X682
C615
CERAMIC CAP.(AX) B K 100pF/50V
CCA1JKT0B101
C729
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
C616
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
CDA1CKT0X682
C618
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
C731
CERAMIC CAP.(AX) X K 6800pF/16V
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
C733
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
MYLAR CAP. 0.1µF/50V K
2250104S
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
CDA1CKT0X682
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
C736
CERAMIC CAP.(AX) X K 6800pF/16V
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
C738
ELECTROLYTIC CAP. 0.47µF/50V M or
CE1JMASTLR47
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
MYLAR CAP. 0.1µF/50V K
2250104S
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
C642#
SAFETY CAP. 4700pF/250V or
CCG2EMA0F472
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
#
SAFETY CAP. E M 4700pF/250V KH or
CCG2EMP0E472
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
20030408
C751
13-3
L6610EL
Ref. No.
Description
ELECTROLYTIC CAP. 1µF/50V M
C757
C761
C767
C773
C781
C801
C803
C804
C808
C809
C812
C814
C821
C827
C831
C851
CE1JMASTLR10
C1522
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
C1531
CERAMIC CAP.(AX) B K 470pF/50V
CCA1JKT0B471
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
C1532
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
CONNECTORS
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
CN301
CONNECTOR BASE, 6P TUC-P06P-B1
J3TUA06TG001
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
CN571#
CONNECTOR BASE, 5P TV-50P-05-V3 or
J3TVC05TG002
ELECTROLYTIC CAP. 0.1µF/50V M or
CE1JMASTLR10
#
CONNECTOR BASE, 5P RTB-1.5-5P or
J3RTC05JG001
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDLR10
#
CONNECTOR BASE, 5P W-P3005-02
1730812
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
CN691#
CONNECTOR BASE, 2P TV-50P-02-V3 or
J3TVC02TG002
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
#
CONNECTOR BASE, 2P RTB-1.5-2P
J3RTC02JG001
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
CN801
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002
000 or
ELECTROLYTIC CAP. 470µF/25V M or
CE1EMASTL471
CE1EMASDL471
ELECTROLYTIC CAP. 470µF/25V M or
CE1EMASTL471
ELECTROLYTIC CAP. 470µF/25V M
CE1EMASDL471
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
MYLAR CAP. 0.1µF/50V K
2250104S
FILM CAP.(P) 0.1µF/50V J or
CMA1JJS00104
FILM CAP.(P) 0.1µF/50V J or
CA1J104MS029
FILM CAP.(P) 0.1µF/50V J TV or
CMB1JJS00104
MYLAR CAP. 0.1µF/50V K
2250104S
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL1R0
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASTL010
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL010
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
ELECTROLYTIC CAP. 22µF/50V M or
CE1JMASTL220
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
ELECTROLYTIC CAP. 1000µF/25V M or
CE1EMZNTL102
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZPDL102
ELECTROLYTIC CAP. 100µF/16V M or
CE1CMASTL101
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASDL101
ELECTROLYTIC CAP. 100µF/25V M or
CE1EMASTL101
ELECTROLYTIC CAP. 100µF/25V M
CE1EMASDL101
CE1JMASTL100
CE1JMASDL100
C852
ELECTROLYTIC CAP. 470µF/16V M or
CE1CMASTL471
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASDL471
C853
CERAMIC CAP.(AX) F Z 0.01µF/25V
CDA1EZT0F103
C963
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C964#
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
#
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C1510
Part No.
CCA1JKT0B471
CE1JMASDLR10
ELECTROLYTIC CAP. 10µF/50V M
C1502
Description
CERAMIC CAP.(AX) B K 470pF/50V
ELECTROLYTIC CAP. 0.1µF/50V M or
ELECTROLYTIC CAP. 10µF/50V M or
C1501
Ref. No.
C1521
ELECTROLYTIC CAP. 0.1µF/50V M
ELECTROLYTIC CAP. 470µF/25V M
C802
Part No.
CE1JMASDL010
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASTL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASTL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
CERAMIC CAP. B K 2200pF/2KV or
CCD3DKD0B222
CERAMIC CAP. B K 2200pF/2KV or
CCD3DKP0B222
CERAMIC CAP. B K 2200pF/2KV
CA3D222MR030
C1511
CERAMIC CAP.(AX) B K 470pF/50V
CCA1JKT0B471
C1512
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
20030408
STRAIGHT PIN HEADER, 2P 173981-2
CN802
1770258
STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002
000 or
STRAIGHT PIN HEADER, 2P 173981-2
1770258
DIODES
D131
D171
ZENER DIODE MTZJT-775.1B or
QDTB0MTZJ5R1
ZENER DIODE DZ-5.1BSBT265
NDTB0DZ5R1BS
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
D311
ZENER DIODE MTZJT-775.1B or
QDTB0MTZJ5R1
ZENER DIODE DZ-5.1BSBT265
NDTB0DZ5R1BS
D312
ZENER DIODE MTZJT-775.1B or
QDTB0MTZJ5R1
ZENER DIODE DZ-5.1BSBT265
NDTB0DZ5R1BS
D313
ZENER DIODE MTZJT-775.1B or
QDTB0MTZJ5R1
ZENER DIODE DZ-5.1BSBT265
NDTB0DZ5R1BS
D322
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
D323
ZENER DIODE MTZJT-779.1B or
QDTB0MTZJ9R1
ZENER DIODE DZ-9.1BSBT265
NDTB0DZ9R1BS
D326
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D351
D352
D353
D501
DIODE 1SS176TPA7
1SS176T
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
DIODE FR104-B or
NDLZ000FR104
RECTIFIER DIODE ERA22-02 or
QDPZ0ERA2202
RECTIFIER DIODE 10ELS2
QDQZ0010ELS2
D502#
ZENER DIODE MTZJT-7724B or
QDTB00MTZJ24
#
ZENER DIODE DZ-24BSBT265
NDTB00DZ24BS
D503#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
DIODE 1SS176TPA7
1SS176T
D513
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
D545
ZENER DIODE MTZJT-776.8B or
QDTB0MTZJ6R8
ZENER DIODE DZ-6.8BSBT265
NDTB0DZ6R8BS
D546
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
13-4
L6610EL
Ref. No.
Description
DIODE 1SS176TPA7
Part No.
Ref. No.
Description
Part No.
1SS176T
#
FAST RECOVERY DIODE ERB44-02
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D658#
DIODE 1ZC18 or
QDQZ0001ZC18
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
ZENER DIODE RD18F
QDQZ000RD18F
DIODE 1SS176TPA7
1SS176T
D660
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
ZENER DIODE MTZJT-773.0B or
QDTB0MTZJ3R0
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
ZENER DIODE DZ-3.0BSBT265
NDTB0DZ3R0BS
D558
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
DIODE 1SS176TPA7
D572
RECTIFIER DIODE ERA22-02 or
QDPZ0ERA2202
RECTIFIER DIODE 10ELS2
QDQZ0010ELS2
D573
RECTIFIER DIODE ERA22-02 or
QDPZ0ERA2202
D671#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
RECTIFIER DIODE 10ELS2
QDQZ0010ELS2
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D580
DIODE ERD07-15
QDLZ0ERD0715
#
DIODE 1SS176TPA7
1SS176T
D582
FAST RECOVERY DIODE ERD38-06
QDQZ0ERD3806
D672
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D583
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
DIODE 1SS176TPA7
1SS176T
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D547
D552#
QDPZ0ERB4402
DIODE 1SS176TPA7
1SS176T
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
NDTZ001N4148
SWITCHING DIODE 1N4148 or
NDTZ001N4148
1SS176T
DIODE 1SS176TPA7
1SS176T
ZENER DIODE MTZJT-7736B or
QDTB00MTZJ36
ZENER DIODE DZ-36BSBT265
NDTB00DZ36BS
D661
D666
D673
D584#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
#
DIODE 1SS176TPA7
1SS176T
D675#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D585
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
DIODE 1SS176TPA7
1SS176T
DIODE 1SS176TPA7
1SS176T
D692#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D591#
ZENER DIODE MTZJT-7736B or
QDTB00MTZJ36
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
ZENER DIODE DZ-36BSBT265
NDTB00DZ36BS
#
DIODE 1SS176TPA7
1SS176T
D594#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D694#
ZENER DIODE MTZJT-7715B or
QDTB00MTZJ15
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
ZENER DIODE DZ-15BSBT265
NDTB00DZ15BS
#
DIODE 1SS176TPA7
1SS176T
D696
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D597
ZENER DIODE MTZJT-776.8B or
QDTB0MTZJ6R8
SWITCHING DIODE 1N4148 or
NDTZ001N4148
DIODE 1SS176TPA7
1SS176T
ZENER DIODE DZ-6.8BSBT265
NDTB0DZ6R8BS
D605#
DIODE 1N5406
NDLZ001N5406
D697#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D606#
DIODE 1N5406
NDLZ001N5406
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D607#
DIODE 1N5406
NDLZ001N5406
#
DIODE 1SS176TPA7
1SS176T
D608#
DIODE 1N5406
NDLZ001N5406
D698#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D609
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
DIODE 1SS176TPA7
1SS176T
DIODE 1SS176TPA7
1SS176T
D826
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D611#
ZENER DIODE MTZJT-7720B or
QDTB00MTZJ20
SWITCHING DIODE 1N4148 or
NDTZ001N4148
#
ZENER DIODE DZ-20BSBT265
NDTB00DZ20BS
DIODE 1SS176TPA7
1SS176T
D613
ZENER DIODE MTZJT-778.2B or
QDTB0MTZJ8R2
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
ZENER DIODE DZ-8.2BSBT265
NDTB0DZ8R2BS
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D614
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
DIODE 1SS176TPA7
1SS176T
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D841#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
DIODE 1SS176TPA7
1SS176T
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D615
SWITCHING DIODE 1N4148 T-77
QDTZ001N4148
#
DIODE 1SS176TPA7
1SS176T
D621
BEAD INDUCTORS FBA04HA600VB-00
LLBF00STU026
D842#
ZENER DIODE MTZJT-776.2B or
QDTB0MTZJ6R2
D651#
FAST RECOVERY DIODE 30DF6 or
QDWZ00030DF6
#
ZENER DIODE DZ-6.2BSBT265
NDTB0DZ6R2BS
#
DIODE ERD29-06J or
QD4Z0ERD2906
D851#
ZENER DIODE MTZJT-7712B or
QDTB00MTZJ12
#
FAST RECOVERY DIODE FE201-6
QDLZ00FE2016
#
ZENER DIODE DZ-12BSBT265
NDTB00DZ12BS
D652#
DIODE FR154 or
NDLZ000FR154
D853
ZENER DIODE MTZJT-779.1B or
QDTB0MTZJ9R1
#
FAST RECOVERY DIODE ERB44-02
QDPZ0ERB4402
D653#
DIODE FR154 or
NDLZ000FR154
#
FAST RECOVERY DIODE ERB44-02
D654#
SWITCHING DIODE 1SS133(T-77) or
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D855#
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
#
DIODE 1SS176TPA7
1SS176T
#
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D655
ZENER DIODE 1ZB180
QDQZ001ZB180
#
DIODE 1SS176TPA7
1SS176T
D656#
ZENER DIODE MTZJT-776.8B or
QDTB0MTZJ6R8
D896
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
#
ZENER DIODE DZ-6.8BSBT265
NDTB0DZ6R8BS
SWITCHING DIODE 1N4148 or
NDTZ001N4148
D657#
DIODE FR154 or
NDLZ000FR154
DIODE 1SS176TPA7
1SS176T
20030408
D827
ZENER DIODE DZ-9.1BSBT265
NDTB0DZ9R1BS
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
QDPZ0ERB4402
SWITCHING DIODE 1N4148 or
NDTZ001N4148
QDTZ001SS133
DIODE 1SS176TPA7
1SS176T
D854
13-5
L6610EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
D963
ZENER DIODE MTZJT-775.6B or
QDTB0MTZJ5R6
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
ZENER DIODE DZ-5.6BSBT265
NDTB0DZ5R6BS
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
D966
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
SWITCHING DIODE 1N4148 or
NDTZ001N4148
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
DIODE 1SS176TPA7
1SS176T
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
SWITCHING DIODE 1N4148 or
NDTZ001N4148
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
DIODE 1SS176TPA7
1SS176T
Q111#
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
#
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
D1501
ICS
IC33
IC:VIF/SIF DETECTOR M61111FP
QSZBA0SMB010
#
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
IC151
IC:MEMORY AT24C02N-10SC or
NSMMA0SAZ012
#
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
IC(EEPROM) M24C02-MN6 or
NSMMA0SSS028
#
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
IC:MEMORY BR24C02F-W or
QSMBA0SRM003
#
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
IC:MEMORY BR24C02F or
QSMMA0SRM003
#
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
IC:MEMORY S524C20D21 or
NSZBA0SSM028
#
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
IC(EEP-ROM) M24C02-WMN6
NSZAA0SSS004
Q131
RES. BUILT-IN TRANSISTOR BA1F4M-T or
QQSZ00BA1F4M
IC333
IC M61272M8-054FP
QSZAA0RMB130
IC431
IC:MTS DECORDER AN5832SA
QSZBA0TMS003
IC551#
IC:VERTICAL OUTPUT LA78041
QSZBA0SSY006
IC601#
PHOTOCOUPLER LTV-817B-F or
NPEB0LTV817F
#
PHOTOCOUPLER LTV-817C-F
IC771
IC:SWITCHING TC4052BF(EL) or
IC801
RES. BUILT-IN TRANSISTOR KRC103M
NQSZ0KRC103M
Q141
RES. BUILT-IN TRANSISTOR BA1F4M-T or
QQSZ00BA1F4M
RES. BUILT-IN TRANSISTOR KRC103M
NQSZ0KRC103M
Q191
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
NPEC0LTV817F
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
QSZBA0TTS096
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
IC:SWITCHING CD4052BCSJX
NSZBA0TF3079
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
AUDIO POWER IC AN17805A
QSZBA0SMS007
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
COILS
L1
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
L2
INDUCTOR 22µH-K-5FT or
LLARKBSTU220
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
INDUCTOR 22µH-K
LLARKDQKA220
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
INDUCTOR 15µH-J-26T or
LLAXJATTU150
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
INDUCTOR 15µH-K-26T
LLAXKDTKA150
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
INDUCTOR 22µH-J-26T or
LLAXJATTU220
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
INDUCTOR 22µH-K-26T
LLAXKDTKA220
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
L32
L33
L34
Q321
INDUCTOR 100µH-J-5FT or
LLARJCSTU101
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
INDUCTOR 100µH-K
LLARKDQKA101
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
INDUCTOR 22µH-K-5FT or
LLARKBSTU220
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
INDUCTOR 22µH-K
LLARKDQKA220
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
INDUCTOR 22µH-K-5FT or
LLARKBSTU220
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
INDUCTOR 22µH-K
LLARKDQKA220
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
INDUCTOR 100µH-J-5FT or
LLARJCSTU101
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
INDUCTOR 100µH-K
LLARKDQKA101
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
L341
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
L342
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
L551#
LINEARITY COIL ELH5L6136N
LLBD00PMS008
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
L562#
CHOKE COIL ELC18B821LK or
LLC821KMS001
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
QQSJ02SC2785
NQS10KTC3199
L51
L111
L112
L301
Q531
Q533
#
CHOKE COIL CSA-LF050
LLBD00ZSA002
TRANSISTOR 2SC2785(J) or
L564#
CHOKE COIL ELC18E821EN
LLBD00ZMS042
TRANSISTOR KTC3199(GR) or
L588
CHOKE COIL 47µH-K or
LLBD00PKV007
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
POT COIL 47µH K
LLBD**DMM001
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
L601
LINE FILTER MS036
LLBG00ZY2009
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
#
LINE FILTER JLB2808 or
LLBG00ZXB004
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
#
LINE FILTER CSA-LF032
LLBG00ZSA007
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
QQSF02SA1175
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR KTA1266(GR) or
NQS40KTA1266
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR 2SA1318(T)-AANP or
2SA1318TZ
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SA1318(U)-AANP or
2SA1318UZ
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
Q547
TRANSISTORS
Q21
Q33
TRANSISTOR 2SA1175(F) or
20030408
Q551#
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
#
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
13-6
L6610EL
Ref. No.
Description
#
TRANSISTOR KTA1266(GR) or
#
#
#
Q552#
Part No.
Ref. No.
Description
Part No.
NQS40KTA1266
TRANSISTOR KTC3199(GR) or
TRANSISTOR 2SA1318(T)-AANP or
2SA1318TZ
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR 2SA1318(U)-AANP or
2SA1318UZ
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR KTD2059(O) or
NQ400KTD2059
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
#
TRANSISTOR KTD2059(Y) or
NQ4Y0KTD2059
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
#
TRANSISTOR 2SD1666S
QQES02SD1666
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
Q561
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
Q571#
TRANSISTOR 2SD2553 or
QQWZ02SD2553
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
#
TRANSISTOR 2SC5902
QQWZ02SC5902
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
Q572#
TRANSISTOR 2SC1627Y-TPE2
QQSY02SC1627
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
Q601#
FET 2SK3407
QFFZ02SK3407
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
Q602#
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
#
TRANSISTOR 2SC2120-Y(TPE2)
QQSY02SC2120
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
Q652#
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
#
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
#
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
#
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
#
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
#
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
#
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
#
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
Q672#
TRANSISTOR 2SA950(O) or
Q2SA9500TPE2
#
TRANSISTOR 2SA950(Y)
Q673
Q674
Q681
Q682
Q683
Q696
Q751
Q761
Q791
Q792
Q793
NQS10KTC3199
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
Q2SA950YTPE2
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR KTA1266(GR) or
NQS40KTA1266
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR 2SA1318(T)-AANP or
2SA1318TZ
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SA1318(U)-AANP or
2SA1318UZ
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
RES. BUILT-IN TRANSISTOR BA1F4M-T or
QQSZ00BA1F4M
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
Q794
Q825
RES. BUILT-IN TRANSISTOR KRC103M
NQSZ0KRC103M
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
Q831#
TRANSISTOR 2SB892(S) or
QQSS002SB892
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
#
TRANSISTOR 2SB892(T)
QQST002SB892
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
Q832
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
RES. BUILT-IN TRANSISTOR BA1F4M-T or
QQSZ00BA1F4M
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
RES. BUILT-IN TRANSISTOR KRC103M
NQSZ0KRC103M
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
20030408
Q841
13-7
L6610EL
Ref. No.
Description
TRANSISTOR 2SC3331(U)-AANP or
Q851
Q951
Q956
Part No.
Ref. No.
Description
Part No.
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
2SC3331UZ
R139
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R140
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
R141
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R142
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
R150
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR KTA1266(GR) or
NQS40KTA1266
R153
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
TRANSISTOR 2SA1318(T)-AANP or
2SA1318TZ
TRANSISTOR 2SA1318(U)-AANP or
2SA1318UZ
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
TRANSISTOR KTA1266(GR) or
NQS40KTA1266
R154
R156
R157
TRANSISTOR 2SA1318(T)-AANP or
2SA1318TZ
TRANSISTOR 2SA1318(U)-AANP or
2SA1318UZ
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
Q961#
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
#
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
#
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R161
R23
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R163
R158
R159
RESISTORS
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
R31
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R164
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R33
CARBON RES. 1/4W J 270 Ω or
RCX4JATZ0271
R165
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
CARBON RES. 1/6W J 270 Ω
RCX6JATZ0271
R166
CARBON RES. 1/4W J 6.8k Ω
RCX4JATZ0682
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
R167
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
R168
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R36
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R170
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R37
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
R171
CARBON RES. 1/4W J 3.9k Ω
RCX4JATZ0392
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
R172
PCB JUMPER D0.6-P5.0
JW5.0T
R38
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R173
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R39
CARBON RES. 1/4W J 27k Ω
RCX4JATZ0273
R174
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R40
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R176
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R43
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R44
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R34
R177
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R51
CARBON RES. 1/4W J 220k Ω
RCX4JATZ0224
R52
CARBON RES. 1/4W J 220k Ω
RCX4JATZ0224
R54
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R193
R102
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R195
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R103
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R196
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R104
CARBON RES. 1/4W J 2.7k Ω
RCX4JATZ0272
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R105
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R198
PCB JUMPER D0.6-P5.0
JW5.0T
R108
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R301
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R109
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R302
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R111
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R112
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R113
CARBON RES. 1/4W J 470k Ω
RCX4JATZ0474
R178
R303
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
R305
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
R311
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R116
PCB JUMPER D0.6-P5.0
JW5.0T
R312
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R132
PCB JUMPER D0.6-P5.0
JW5.0T
R313
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R133
PCB JUMPER D0.6-P5.0
JW5.0T
R320
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R135
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R323
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R136
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R326
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R114
R137
R138
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R327
PCB JUMPER D0.6-P5.0
JW5.0T
CARBON RES. 1/4W J 220k Ω
RCX4JATZ0224
R328
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R329
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
20030408
13-8
L6610EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R552#
METAL OXIDE FILM RES. 1W J 8.2 Ω or
RN018R2ZU001
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
#
METAL OXIDE FILM RES. 1W J 8.2 Ω
RN018R2DP003
CARBON RES. 1/4W J 330 Ω or
RCX4JATZ0331
R553
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
CARBON RES. 1/6W J 330 Ω
RCX6JATZ0331
R554
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R342
PCB JUMPER D0.6-P5.0
JW5.0T
R555
CARBON RES. 1/4W J 680 Ω or
RCX4JATZ0681
R344
CARBON RES. 1/4W J 6.8k Ω
RCX4JATZ0682
CARBON RES. 1/6W J 680 Ω
RCX6JATZ0681
R345
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R556
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R346
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R557
CARBON RES. 1/4W J 18k Ω
RCX4JATZ0183
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
R558
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
R347
PCB JUMPER D0.6-P5.0
JW5.0T
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
R348
CARBON RES. 1/4W J 27k Ω
RCX4JATZ0273
R559
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R355
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R560
CARBON RES. 1/4W J 150k Ω
RCX4JATZ0154
R356
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R561
CARBON RES. 1/4W J 1.2k Ω
RCX4JATZ0122
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R562
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R563
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R564
CARBON RES. 1/4W J 270k Ω
RCX4JATZ0274
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R565
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R566
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R362
PCB JUMPER D0.6-P5.0
JW5.0T
R567
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R417
CARBON RES. 1/4W J 180k Ω
RCX4JATZ0184
R568
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R422
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
R427
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R569
CARBON RES. 1/4W J 560k Ω
RCX4JATZ0564
R444
CARBON RES. 1/4W J 10M Ω
RCX4JATZ0106
R575#
CARBON RES. 1/4W J 15 Ω or
RCX4JATZ0150
R445
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
#
CARBON RES. 1/6W J 15 Ω
RCX6JATZ0150
R503
CARBON RES. 1/4W J 68k Ω
RCX4JATZ0683
R576
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R504
CARBON RES. 1/4W J 3.3 Ω or
RCX4JATZ03R3
CARBON RES. 1/6W J 3.3 Ω
RCX6JATZ03R3
R505
CARBON RES. 1/4W J 1.8k Ω
RCX4JATZ0182
R506
CARBON RES. 1/4W J 2.7 Ω or
RCX4JATZ02R7
CARBON RES. 1/6W J 2.7 Ω
RCX6JATZ02R7
CARBON RES. 1/4W J 2.7 Ω or
RCX4JATZ02R7
CARBON RES. 1/6W J 2.7 Ω
RCX6JATZ02R7
CARBON RES. 1/4W J 2.7 Ω or
RCX4JATZ02R7
R581
PCB JUMPER D0.6-P5.0
JW5.0T
CARBON RES. 1/6W J 2.7 Ω
RCX6JATZ02R7
R583#
METAL OXIDE FILM RES. 2W J 6.8 Ω or
RN026R8ZU001
RN026R8DP004
R330
R333
R357
R358
R507
R508
R577
R578
R579
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
CARBON RES. 1/4W J 330 Ω or
RCX4JATZ0331
CARBON RES. 1/6W J 330 Ω
RCX6JATZ0331
CARBON RES. 1/4W J 15 Ω or
RCX4JATZ0150
CARBON RES. 1/6W J 15 Ω
RCX6JATZ0150
CARBON RES. 1/4W J 15 Ω or
RCX4JATZ0150
CARBON RES. 1/6W J 15 Ω
RCX6JATZ0150
R513#
METAL OXIDE FILM RES. 2W J 4.7 Ω or
RN024R7ZU001
#
METAL OXIDE FILM RES. 2W J 6.8 Ω
#
METAL OXIDE FILM RES. 2W J 4.7 Ω
RN024R7DP004
R584#
PCB JUMPER D0.6-P5.0
JW5.0T
R514
CARBON RES. 1/4W J 2.7k Ω
RCX4JATZ0272
R585#
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
CARBON RES. 1/4W J 680 Ω or
RCX4JATZ0681
R586#
CARBON RES. 1/4W J 470k Ω
RCX4JATZ0474
CARBON RES. 1/6W J 680 Ω
RCX6JATZ0681
R587
CARBON RES. 1/4W J 470k Ω
RCX4JATZ0474
R520#
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R588
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R522
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R589#
CARBON RES. 1/4W J 39k Ω
RCX4JATZ0393
R531
CARBON RES. 1/4W J 1.8k Ω
RCX4JATZ0182
R590
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R532
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R591#
CARBON RES. 1/4W J 180k Ω
RCX4JATZ0184
R533
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R592#
CARBON RES. 1/4W J 220k Ω
RCX4JATZ0224
R534
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R593#
CARBON RES. 1/4W J 68k Ω
RCX4JATZ0683
R535
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
R594#
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
R596
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
CARBON RES. 1/4W J 680 Ω or
RCX4JATZ0681
R597
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
CARBON RES. 1/6W J 680 Ω
RCX6JATZ0681
R598#
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
CARBON RES. 1/4W J 680 Ω or
RCX4JATZ0681
R599#
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
CARBON RES. 1/6W J 680 Ω
RCX6JATZ0681
R601#
CEMENT RES. 7W K 0.56 Ω or
RW07R56DP007
R516
R541
R542
CARBON RES. 1/4W J 680 Ω or
RCX4JATZ0681
#
CEMENT RESISTOR 7W K 0.56 Ω H=10MM
RW07R56PG001
CARBON RES. 1/6W J 680 Ω
RCX6JATZ0681
R602
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
R544
CARBON RES. 1/4W J 1.8k Ω
RCX4JATZ0182
R603
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
R545
CARBON RES. 1/4W J 6.8k Ω
RCX4JATZ0682
R604
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
R546
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R605
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
R547
CARBON RES. 1/4W J 2.7k Ω
RCX4JATZ0272
R607
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
R548
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R549
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R551#
METAL OXIDE FILM RES. 1W J 1k Ω or
RN01102ZU001
#
METAL OXIDE FILM RES. 1W J 1k Ω
RN01102DP003
R543
20030408
R608
R609
13-9
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
L6610EL
Ref. No.
Description
Part No.
R613#
CEMENT RES. 5W K 0.27 Ω or
RW05R27DP005
#
CEMENT RESISTOR 5W K 0.27 Ω
RW05R27PG001
R614
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
R616
CARBON RES. 1/4W J 10k Ω
R618
Ref. No.
Description
Part No.
CARBON RES. 1/6W J 82 Ω
RCX6JATZ0820
CARBON RES. 1/4W J 82 Ω or
RCX4JATZ0820
CARBON RES. 1/6W J 82 Ω
RCX6JATZ0820
R704
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
RCX4JATZ0103
R705
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
CARBON RES. 1/4W J 390 Ω or
RCX4JATZ0391
R706
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
CARBON RES. 1/6W J 390 Ω
RCX6JATZ0391
R707
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R620#
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R708
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
#
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R709
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R621
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R711
CARBON RES. 1/4W J 82 Ω or
RCX4JATZ0820
R622
CARBON RES. 1/4W J 47 Ω or
RCX4JATZ0470
CARBON RES. 1/6W J 47 Ω
RCX6JATZ0470
CARBON RES. 1/4W J 39 Ω or
RCX4JATZ0390
CARBON RES. 1/6W J 39 Ω
RCX6JATZ0390
R651#
METAL OXIDE FILM RES. 2W J 22k Ω or
RN02223ZU001
#
METAL OXIDE FILM RES. 2W J 22k Ω
RN02223DP004
R652
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
R653
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R654#
CARBON RES. 1/4W J 2.7k Ω
RCX4JATZ0272
R655
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
R656#
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
R657
CARBON RES. 1/4W J 15k Ω
R658
R660
R623
R702
R713
R716
CARBON RES. 1/6W J 82 Ω
RCX6JATZ0820
CARBON RES. 1/4W J 330 Ω or
RCX4JATZ0331
CARBON RES. 1/6W J 330 Ω
RCX6JATZ0331
CARBON RES. 1/4W J 82 Ω or
RCX4JATZ0820
CARBON RES. 1/6W J 82 Ω
RCX6JATZ0820
CARBON RES. 1/4W J 330 Ω or
RCX4JATZ0331
CARBON RES. 1/6W J 330 Ω
RCX6JATZ0331
CARBON RES. 1/4W J 82 Ω or
RCX4JATZ0820
CARBON RES. 1/6W J 82 Ω
RCX6JATZ0820
CARBON RES. 1/4W J 82 Ω or
RCX4JATZ0820
CARBON RES. 1/6W J 82 Ω
RCX6JATZ0820
R724
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
RCX4JATZ0153
R725
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
CARBON RES. 1/4W J 470k Ω
RCX4JATZ0474
R726
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R727
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
R728
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R661#
CARBON RES. 1/4W J 120k Ω
RCX4JATZ0124
R729
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R662#
CARBON RES. 1/4W J 82k Ω
RCX4JATZ0823
R731
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R663#
PCB JUMPER D0.6-P5.0
JW5.0T
R732
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R664#
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R733
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R665#
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R736
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R666#
METAL OXIDE FILM RES. 1W J 100k Ω or
RN01104ZU001
R737
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
#
METAL OXIDE FILM RES. 1W J 100k Ω
RN01104DP003
R738
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R667#
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R741
PCB JUMPER D0.6-P5.0
JW5.0T
R668#
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R742
PCB JUMPER D0.6-P5.0
JW5.0T
R669#
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R743
PCB JUMPER D0.6-P5.0
JW5.0T
R670#
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R746
CARBON RES. 1/4W J 75 Ω or
RCX4JATZ0750
R671#
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
CARBON RES. 1/6W J 75 Ω
RCX6JATZ0750
R672#
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
CARBON RES. 1/4W J 75 Ω or
RCX4JATZ0750
R673#
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
CARBON RES. 1/6W J 75 Ω
RCX6JATZ0750
R674
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
CARBON RES. 1/4W J 75 Ω or
RCX4JATZ0750
R676
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
CARBON RES. 1/6W J 75 Ω
RCX6JATZ0750
R677
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
R751
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R678
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R752
CARBON RES. 1/4W J 27k Ω
RCX4JATZ0273
R679#
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R753
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R680
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R754
CARBON RES. 1/4W J 18k Ω
RCX4JATZ0183
R681#
CARBON RES. 1/4W J 12 Ω or
RCX4JATZ0120
R755
CARBON RES. 1/4W J 1.8k Ω
RCX4JATZ0182
#
CARBON RES. 1/6W J 12 Ω
RCX6JATZ0120
R756
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R682#
METAL OXIDE FILM RES. 2W J 33 Ω or
RN02330ZU001
#
METAL OXIDE FILM RES. 2W J 33 Ω
RN02330DP004
R718
R721
R722
R747
R748
R757
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
CARBON RES. 1/4W J 560 Ω or
RCX4JATZ0561
R683#
METAL RESISTOR 2W J 39 Ω or
RN02390ZU001
CARBON RES. 1/6W J 560 Ω
RCX6JATZ0561
#
METAL OXIDE FILM RES. 2W J 39 Ω
RN02390DP004
R761
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R686
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R762
CARBON RES. 1/4W J 27k Ω
RCX4JATZ0273
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R763
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
CARBON RES. 1/4W J 10 Ω or
RCX4JATZ0100
R764
CARBON RES. 1/4W J 18k Ω
RCX4JATZ0183
CARBON RES. 1/6W J 10 Ω
RCX6JATZ0100
R765
CARBON RES. 1/4W J 1.8k Ω
RCX4JATZ0182
R694#
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R766
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
R696#
CARBON RES. 1/4W J 10 Ω or
RCX4JATZ0100
#
CARBON RES. 1/6W J 10 Ω
RCX6JATZ0100
R697
PCB JUMPER D0.6-P5.0
JW5.0T
R701
CARBON RES. 1/4W J 82 Ω or
RCX4JATZ0820
R687
20030408
R767
R771
13-10
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
CARBON RES. 1/4W J 560 Ω or
RCX4JATZ0561
CARBON RES. 1/6W J 560 Ω
RCX6JATZ0561
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
L6610EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
R772
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R791
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R792
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R793
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R803
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
CARBON RES. 1/4W J 100 Ω or
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R811
CARBON RES. 1/4W J 18k Ω
R812
CARBON RES. 1/4W J 18k Ω
R817
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R818
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
AC601#
AC CORD LA-2413
R827
CARBON RES. 1/4W J 1k Ω or
RCX4JATZ0102
B-6
HEAT SINK(PGM)ASSEMBLY L6250UA
0EM407156
CARBON RES. 1/6W J 1k Ω
RCX6JATZ0102
B-7
HEAT SINK(PFN)ASSEMBLY L1520UZ
0EM406353
R828
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
B-8
HEAT SINK(PGN)ASSEMBLY L6250UA
0EM407158
R829
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
B-9
HEAT SINK(PGO) L6250UA
0EM407159
R831
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
BC571
BEAD INDUCTORS FBA04HA600VB-00
LLBF00STU026
JW5.0T
R804
TACT SWITCH SKHHAM
SW104
SST0101AL029
TACT SWITCH SKQSAB or
SST0101AL038
TACT SWITCH KSM0612B or
SST0101HH003
TACT SWITCH SKHHAM
SST0101AL029
TACT SWITCH SKQSAB or
SST0101AL038
RCX6JATZ0101
TACT SWITCH KSM0612B or
SST0101HH003
RCX4JATZ0101
TACT SWITCH SKHHAM
SST0101AL029
TACT SWITCH SKQSAB or
SST0101AL038
RCX4JATZ0183
TACT SWITCH KSM0612B or
SST0101HH003
RCX4JATZ0183
TACT SWITCH SKHHAM
SST0101AL029
SW105
SW106
MISCELLANEOUS
WAC0172LW007
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
BC572
PCB JUMPER D0.6-P5.0
R832
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
BC602
PCB JUMPER D0.6-P5.0
JW5.0T
R833
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
BC603
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
LLBF00ZTU021
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
BC652
BEAD INDUCTORS FBR07HA121TB-00
R834
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
BC653
PCB JUMPER D0.6-P5.0
JW5.0T
R841
METAL OXIDE FILM RES. 2W J 0.47 Ω or
RN02R47ZU001
BC654
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
METAL OXIDE FILM RES. 2W J 0.47 Ω
RN02R47DP004
BC655
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
CARBON RES. 1/4W J 560 Ω or
RCX4JATZ0561
BC656
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
CARBON RES. 1/6W J 560 Ω
RCX6JATZ0561
BC657
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R843
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
BC691
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R844
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
BC692
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CF31
CERAMIC TRAP 4.5MHz or
FBE455PMR003
R845
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
CERAMIC TRAP 4.5MHz
FBE455PMS001
R851#
CARBON RES. 1/4W J 330 Ω or
RCX4JATZ0331
CERAMIC FILTER SFSRA4M50CF00-B0 or
FBB455PMR004
#
CARBON RES. 1/6W J 330 Ω
RCX6JATZ0331
R855#
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R856#
CARBON RES. 1/4W J 2.2k Ω
R951
CARBON RES. 1/4W J 220 Ω or
R842
CF32
CERAMIC FILTER 4.5MHz
FBB455PMS001
CLN1
LEAD WIRE UL1007 AWG22 BLACK 140MM
WX3001A2FF14
RCX4JATZ0222
CLN2
WIRE 100/BLA/AWG26#1007
WX3001A6FF10
RCX4JATZ0221
CLN3
WIRE UL1007 AWG26 BLACK 170MM
WX3001A6FF17
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
CLN301
WIRE ASSEMBLY WX1L1520-103
WX1L1520-103
R952
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
CLN501
WIRE ASSEMBLY WX1L1520-101
WX1L1520-101
R953
CARBON RES. 1/4W J 47 Ω or
RCX4JATZ0470
F601#
FUSE 4A/125V 237 TYPE or
PAGJ20CAG402
CARBON RES. 1/6W J 47 Ω
RCX6JATZ0470
#
FUSE TDS4A125VU/C or
PAGD20CW3402
CARBON RES. 1/4W J 75 Ω or
RCX4JATZ0750
#
FUSE STC4A125V U/CT or
PAGE20CW3402
CARBON RES. 1/6W J 75 Ω
RCX6JATZ0750
#
FUSE 4.00A/125V
PAGG20CNG402
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
FH601
FUSE HOLDER MSF-015 or
XH01Z00LY001
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
FUSE HOLDER FH-V-03078 or
XH01Z00DK001
R954
R956
R957
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R959
CARBON RES. 1/4W J 75 Ω or
RCX4JATZ0750
FH602
HOLDER, FUSE CNT41-0014
1790424
FUSE HOLDER MSF-015 or
XH01Z00LY001
XH01Z00DK001
CARBON RES. 1/6W J 75 Ω
RCX6JATZ0750
FUSE HOLDER FH-V-03078 or
R961
PCB JUMPER D0.6-P5.0
JW5.0T
HOLDER, FUSE CNT41-0014
1790424
R962
CARBON RES. 1/4W J 470 Ω or
RCX4JATZ0471
GP641#
GAP. FNR-G3.10D
FAZ000LD6005
CARBON RES. 1/6W J 470 Ω
RCX6JATZ0471
JK701
RCA JACK 3P(SW) JPJ4321-01-234
JYRL030HD011
R966#
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
JK702
RCA JACK 2P MSP-282V13 PBSN
JXRL020LY045
R967#
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
JK703
RCA JACK 2P(SW) MSP-292V07 PBSN
JYRL020LY011
JK711
Y/C JACK 1P(SW) MDC-070V1-A
JYEL040LY002
JK721
RCA JACK(YELLOW) MTJ-032-06B-20 or
JXRL010LY050
RCA JACK 1P AV-8.4-9Y
JXRL010RP010
RCA JACK(WHITE) MTJ-032-06B-22 or
JXRL010LY052
RCA JACK 1P AV-8.4-9W
JXRL010RP011
SWITCHES
SW101
SW102
SW103
TACT SWITCH SKQSAB or
SST0101AL038
TACT SWITCH KSM0612B or
SST0101HH003
TACT SWITCH SKHHAM
SST0101AL029
TACT SWITCH SKQSAB or
SST0101AL038
TACT SWITCH KSM0612B or
SST0101HH003
TACT SWITCH SKHHAM
SST0101AL029
JK722
JK723
RCA JACK(RED) MTJ-032-06A-21 or
JYRL010LY014
RCA JACK 1P(RED)WITH SW ITCH AV1-09S-2
JYRL010RP008
TACT SWITCH SKQSAB or
SST0101AL038
JK741
RCA JACK 3P(GBR) MSP-213VS5
JXRL030LY028
TACT SWITCH KSM0612B or
SST0101HH003
JS102
PCB JUMPER D0.6-P5.0
JW5.0T
20030408
13-11
L6610EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
JS104
PCB JUMPER D0.6-P5.0
JW5.0T
JS105
PCB JUMPER D0.6-P5.0
JW5.0T
L1501#
INDUCTOR 150µH-J-5FT or
LLARJCSTU151
JS171
PCB JUMPER D0.6-P15.0
JW15.0T
#
INDUCTOR 150µH-K
LLARKDQKA151
JS191
PCB JUMPER D0.6-P5.0
JW5.0T
L1511
PCB JUMPER D0.6-P5.0
JW5.0T
JS301
PCB JUMPER D0.6-P5.0
JW5.0T
L1521
PCB JUMPER D0.6-P5.0
JW5.0T
JS570
PCB JUMPER D0.6-P5.0
JW5.0T
L1531
PCB JUMPER D0.6-P5.0
JW5.0T
JS642
PCB JUMPER D0.6-P10.0
JW10.0T
JS801
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
JS802
PCB JUMPER D0.6-P10.0
JW10.0T
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
JS821
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
JS822
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
JW101
PCB JUMPER D0.6-P7.5
JW7.5T
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
L-1
SCREW, B-TIGHT M3X8 BIND HEAD+ or
GBMB3080
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
SCREW, B-TIGHT M3X8 BIND HEAD+ or
GBMB3080
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC5360 or
QQ9Z02SC5360
COILS
TRANSISTORS
Q1511
SCREW, B-TIGHT M3X8 BIND HEAD+ or
GBMB3080
SCREW, B-TIGHT M3X8 BIND HEAD+
GBMB3080
PB6
CLOTH(65) L7735TR:65X10X0.5T
0EM402149
TRANSISTOR 2SC4544 or
QQ9Z02SC4544
PS691#
THERMISTOR ZPB58BL7R0F
QNQZ58BL7R0F
TRANSISTOR KTC3229
NQ5Z0KTC3229
RCV101
REMOCON RECEIVE UNIT MIM-93M8DKL or
USESJRSUNT02
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
REMOCON RECEIVE UNIT PIC-37042SR or
USESJRSKK034
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
REMOCON RECEIVE UNIT PIC-26042SR-2
USESJRSKK032
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
RL601#
POWER RELAY SDT-S-112LMR
MRNDC12QN014
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
#
POWER RELAY RPEF-12-901 or
MRNDC12KB002
TRANSISTOR KTC3198(GR) or
NQS40KTC3198
#
RELAY DG12D1-O(M)-II or
MRNDC12DEC02
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
#
RELAY ALKS321
MRNDC12MS013
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
SA601#
SURGE ABSORBER AVR-S07D471KAAS or
QVQZ0AVRS07D
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
#
SURGE ABSORBER JVR-07N471K or
NVQZVR07N471
TRANSISTOR 2SC5360 or
QQ9Z02SC5360
#
SURGE ABSORBER CNR-10D471K or
NVQZR10D471K
TRANSISTOR 2SC4544 or
QQ9Z02SC4544
#
SURGE ABSORBER CNR-07D471K or
NVQZR07D471K
TRANSISTOR KTC3229
NQ5Z0KTC3229
Q1512
Q1521
Q1522
#
SURGE ABSORBER PVR-07D471KB
NVQZ07D471KB
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
SF1
SAW FILTER SAFGM45M7VHHzC0B03
FBB456PMR008
TRANSISTOR 2SC2785(H) or
QQSH02SC2785
T571#
FLYBACK TRANS BSC21-2662S
LTF00CPS2036
TRANSISTOR 2SC2785(J) or
QQSJ02SC2785
T572
HORIZONTAL DRAIVE TRANS Y2004 or
LTH00CPY2004
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
NQS40KTC3198
Q1531
HORIZONTAL DRAIVE TRANS CSA-LF044
LTH00CPSA002
TRANSISTOR KTC3198(GR) or
T601#
SWICHING TRANS KD-01714
LTT00CPKT072
TRANSISTOR 2SC3331(T)-AANP or
2SC3331TZ
TH556
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC3331(U)-AANP or
2SC3331UZ
TP300
PCB JUMPER D0.6-P10.0
JW10.0T
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TP301
PCB JUMPER D0.6-P7.5
JW7.5T
TRANSISTOR 2SC5360 or
QQ9Z02SC5360
TP302
PCB JUMPER D0.6-P7.5
JW7.5T
TRANSISTOR 2SC4544 or
QQ9Z02SC4544
TP500
PCB JUMPER D0.6-P7.5
JW7.5T
TRANSISTOR KTC3229
NQ5Z0KTC3229
TP501
PCB JUMPER D0.6-P7.5
JW7.5T
TP591
PCB JUMPER D0.6-P5.0
JW5.0T
TP592
PCB JUMPER D0.6-P5.0
JW5.0T
TP601
PCB JUMPER D0.6-P7.5
JW7.5T
TU1
TUNER UNIT TEQH9-001A
UTUNNTUAL032
VR561
CARBON P.O.T. 20k Ω B or
VRCB203KA011
CARBON P.O.T. 20k Ω B
VRCB203HH014
VR562
CARBON P.O.T. 5k Ω B or
VRCB502KA011
Q1532
RESISTORS
R1501
R1502
R1503
R1509
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON P.O.T. 5k Ω B
VRCB502HH014
VR661#
CARBON P.O.T. 50k Ω B or
VRCB503KA011
METAL RESISTOR 3W J 10k Ω or
RN03103ZU001
#
CARBON P.O.T. 50k Ω B
R1510#
VRCB503HH014
#
FIXED METAL OXIDE FILM RES. 3W J 10k Ω
RN03103DP005
X301
X'TAL 3.579545 MHz
FXD355LLN003
R1511
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1512
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1514
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CRT CBA
Ref. No.
Description
CRT CBA
Consists of the following
Part No.
R1515
-----------R1518
CONNECTOR
CN1501
PIN CONNECTOR 005P-5100
20030408
JTEA001TG001
R1519
13-12
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 820 Ω or
RCX4JATZ0821
CARBON RES. 1/6W J 820 Ω
RCX6JATZ0821
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
L6610EL
Ref. No.
Description
Part No.
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R1520#
METAL RESISTOR 3W J 10k Ω or
RN03103ZU001
#
FIXED METAL OXIDE FILM RES. 3W J 10k Ω
RN03103DP005
R1521
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1522
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1524
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 820 Ω or
RCX4JATZ0821
CARBON RES. 1/6W J 820 Ω
RCX6JATZ0821
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
R1525
R1528
R1529
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
R1530#
METAL RESISTOR 3W J 10k Ω or
RN03103ZU001
#
FIXED METAL OXIDE FILM RES. 3W J 10k Ω
RN03103DP005
R1531
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1532
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1534
CARBON RES. 1/4W J 100 Ω or
RCX4JATZ0101
CARBON RES. 1/6W J 100 Ω
RCX6JATZ0101
CARBON RES. 1/4W J 820 Ω or
RCX4JATZ0821
CARBON RES. 1/6W J 820 Ω
RCX6JATZ0821
CARBON RES. 1/4W J 220 Ω or
RCX4JATZ0221
CARBON RES. 1/6W J 220 Ω
RCX6JATZ0221
R1535
R1538
MISCELLANEOUS
BC1501
BEAD INDUCTORS FBR07HA121TB-00
JK1501# CRT SOCKET ISHS40ST or
LLBF00ZTU021
JSCC290PK006
#
CRT SOCKET HPS0521-012212
JSCC290HD012
JS1551
PCB JUMPER D0.6-P5.0
JW5.0T
20030408
13-13
L6610EL
6427FD/EWF2703
L6610UA/16UG
Printed in Japan
2003-05-20 HO