Epson PowerLite Pro Cinema LS9600e User`s guide

Add to my manuals
204 Pages

advertisement

Epson PowerLite Pro Cinema LS9600e User`s guide | Manualzz

PowerLite ® Pro Cinema

LS9600e/LS10000 User's Guide

Contents

PowerLite Pro Cinema LS9600e/LS10000 User's Guide .......................................................................... 9

Introduction to Your Projector ................................................................................................................. 10

Projector Features.............................................................................................................................. 10

Product Box Contents.................................................................................................................... 11

Additional Components ................................................................................................................ 12

Optional Equipment and Replacement Parts................................................................................. 13

Warranty and Registration Information .......................................................................................... 14

Notations Used in the Documentation ................................................................................................ 14

Where to Go for Additional Information .............................................................................................. 14

Projector Part Locations ..................................................................................................................... 15

Projector Parts - Front/Top ............................................................................................................ 15

Projector Parts - Rear .................................................................................................................... 16

Projector Parts - Interface Ports .................................................................................................... 17

Projector Parts - Base.................................................................................................................... 18

Projector Parts - Control Panel and Projector Lights ..................................................................... 19

Projector Parts - Remote Control................................................................................................... 20

Setting Up the Projector ........................................................................................................................... 24

Projector Placement ........................................................................................................................... 24

Projector Setup and Installation Options ....................................................................................... 24

Projection Distance........................................................................................................................ 26

Removing and Attaching the Cable Cover.......................................................................................... 28

Projector Connections ........................................................................................................................ 29

Connecting to Video Sources ........................................................................................................ 29

Connecting to an HDMI Video Source ...................................................................................... 30

Attaching and Removing the HDMI Cable Clip.......................................................................... 30

Connecting to an MHL-Compatible Device ............................................................................... 31

Connecting to a Component Video Source ............................................................................... 32

Connecting to a Composite Video Source ................................................................................ 32

Connecting to Computer Sources.................................................................................................. 33

Connecting to a Computer for VGA Video................................................................................. 33

3

Connecting to a Computer for HDMI Video ............................................................................... 34

Connecting to External Speakers .................................................................................................. 34

Connecting to a Trigger Out Port ................................................................................................... 35

Installing Batteries in the Remote Control .......................................................................................... 36

Using the Projector on a Network ............................................................................................................ 38

Wired Network Monitoring and Control............................................................................................... 38

Connecting to a Wired Network ..................................................................................................... 38

Selecting Wired Network Settings ................................................................................................. 39

Restricted IP Addresses ........................................................................................................... 42

Setting Up Projector Network E-Mail Alerts ........................................................................................ 42

Network Projector E-mail Alert Messages ..................................................................................... 44

Setting Up Network Monitoring .......................................................................................................... 44

Controlling a Networked Projector Using a Web Browser .................................................................. 45

Using Basic Projector Features ............................................................................................................... 48

Turning On the Projector .................................................................................................................... 48

Turning Off the Projector .................................................................................................................... 50

Viewing 3D Images ............................................................................................................................ 51

Pairing the 3D Glasses with the Projector...................................................................................... 53

Charging the 3D Glasses............................................................................................................... 54

3D Viewing Range......................................................................................................................... 55

Selecting the Language for the Projector Menus................................................................................ 55

Adjusting the Image Height ................................................................................................................ 56

Adjusting the Image Position Using Lens Shift .............................................................................. 57

Image Shape...................................................................................................................................... 59

Adjusting Keystone with the Control Panel .................................................................................... 59

Resizing the Image with the Zoom Feature ........................................................................................ 60

Focusing the Image with the Lens Button........................................................................................... 61

Adjusting the Color Convergence (Panel Alignment) ......................................................................... 62

Remote Control Operation ................................................................................................................. 65

Selecting an Image Source ................................................................................................................ 67

Projection Modes ............................................................................................................................... 69

Changing the Projection Mode Using the Menus........................................................................... 69

Image Aspect Ratio ............................................................................................................................ 70

4

Changing the Image Aspect Ratio ................................................................................................. 70

Available Image Aspect Ratios ...................................................................................................... 71

Color Mode......................................................................................................................................... 72

Changing the Color Mode.............................................................................................................. 73

Available Color Modes................................................................................................................... 73

Adjusting the Lens Iris ................................................................................................................... 74

Changing the Super-resolution Setting .............................................................................................. 75

Changing the Super-resolution/4K Enhancement Setting .................................................................. 76

Using Picture in Picture ...................................................................................................................... 77

Available Picture in Picture Options............................................................................................... 79

Adjusting Projector Features ................................................................................................................... 80

Shutting Off the Picture Temporarily .................................................................................................. 80

Locking the Projector's Buttons .......................................................................................................... 81

Unlocking the Projector's Buttons .................................................................................................. 82

Saving Settings to Memory and Using Saved Settings ...................................................................... 82

Saving the Lens Position and Using Saved Lens Positions................................................................ 83

Using WirelessHD ..................................................................................................................................... 86

WirelessHD Transmission Range ...................................................................................................... 86

WirelessHD Remote Control Operation.............................................................................................. 89

Connecting the WirelessHD Transmitter ............................................................................................ 90

Viewing WirelessHD Content ............................................................................................................. 92

Switching WirelessHD Sources.......................................................................................................... 93

Using the WirelessHD Picture in Picture Feature ............................................................................... 94

Adjusting the Menu Settings .................................................................................................................... 95

Using the Projector's Menus............................................................................................................... 95

Image Quality Settings - Image Menu ................................................................................................ 97

Input Signal Settings - Signal Menu.................................................................................................. 100

Projector Feature Settings - Settings Menu...................................................................................... 105

Projector Memory Options - Memory Menu...................................................................................... 112

Projector Information Display - Info Menu ........................................................................................ 113

Projector Reset Options - Reset Menu ............................................................................................. 114

5

Maintaining and Transporting the Projector ......................................................................................... 116

Projector Maintenance ..................................................................................................................... 116

Cleaning the Lens........................................................................................................................ 116

Cleaning the 3D Glasses ............................................................................................................. 117

Cleaning the Projector Case........................................................................................................ 117

Air Filter and Vent Maintenance .................................................................................................. 117

Cleaning the Air Filter.............................................................................................................. 118

Replacing the Air Filter............................................................................................................ 122

Replacing the Remote Control Batteries ..................................................................................... 125

Transporting the Projector................................................................................................................ 127

Solving Problems .................................................................................................................................... 128

Projection Problem Tips ................................................................................................................... 128

Projector Light Status ....................................................................................................................... 128

Solving Image Problems .................................................................................................................. 132

Solutions When No Image Appears............................................................................................. 132

Solutions When "No Signal" Message Appears........................................................................... 133

Displaying From a PC Laptop ................................................................................................. 133

Displaying From a Mac Laptop ............................................................................................... 134

Solutions When "Not Supported" Message Appears ................................................................... 134

Solutions When Only a Partial Image Appears ............................................................................ 134

Solutions When the Image is Not Rectangular ............................................................................ 135

Solutions When the Image Contains Noise or Static ................................................................... 135

Solutions When the Image is Fuzzy or Blurry .............................................................................. 136

Solutions When the Image Brightness or Colors are Incorrect .................................................... 136

Solutions to Panel Alignment Problems....................................................................................... 137

Solutions When a 3D Image Does Not Display Correctly ............................................................ 137

Solutions When a WirelessHD Source Does Not Display Correctly............................................. 138

Solving Projector or Remote Control Operation Problems ............................................................... 139

Solutions to Projector Power or Shut-Off Problems ..................................................................... 139

Solutions to Problems with the Remote Control........................................................................... 139

Solving Network Problems ............................................................................................................... 140

Solutions When Network Alert E-Mails are Not Received............................................................ 140

Solutions When You Cannot Access the Projector Through the Web ......................................... 141

6

Where to Get Help............................................................................................................................ 141

Technical Specifications ........................................................................................................................ 143

General Projector Specifications ...................................................................................................... 143

Projector Light Source Specifications............................................................................................... 145

Remote Control Specifications ......................................................................................................... 145

Projector Dimension Specifications.................................................................................................. 145

Projector Electrical Specifications .................................................................................................... 146

Projector Environmental Specifications............................................................................................ 147

Projector Safety and Approvals Specifications................................................................................. 147

Supported Video Display Formats.................................................................................................... 148

Notices ..................................................................................................................................................... 152

Recycling.......................................................................................................................................... 152

Important Safety Information ............................................................................................................ 152

Laser Safety Information .................................................................................................................. 153

Laser Optical Path ....................................................................................................................... 154

Important Safety Instructions............................................................................................................ 154

Restriction of Use ........................................................................................................................ 157

FCC Compliance Statement............................................................................................................. 157

Wireless Telegraphy Act Regulations.......................................................................................... 158

Trademarks ...................................................................................................................................... 158

Open Source Software License........................................................................................................ 159

Copyright Notice............................................................................................................................... 203

A Note Concerning Responsible Use of Copyrighted Materials................................................... 204

Copyright Attribution .................................................................................................................... 204

7

PowerLite Pro Cinema LS9600e/LS10000 User's Guide

Welcome to the PowerLite Pro Cinema LS9600e/LS10000 User's Guide.

9

Introduction to Your Projector

Refer to these sections to learn more about your projector and this manual.

Projector Features

Notations Used in the Documentation

Where to Go for Additional Information

Projector Part Locations

Projector Features

The PowerLite Pro Cinema LS9600e and LS10000 projectors include these special features:

Bright, high-resolution projection system

• PowerLite Pro Cinema LS9600e: Up to 1300 lumens of color brightness (color light output) and 1300 lumens of white brightness (white light output)

PowerLite Pro Cinema LS10000: Up to 1500 lumens of color brightness (color light output) and 1500 lumens of white brightness (white light output)

Note: Color brightness (color light output) and white brightness (white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.

• 1080p native resolution

• Images up to 300 inches (7.62 m) for projection on any wall or screen

• Laser light source provides Absolute black level and precision detail

• Super-resolution enhances low resolution images to 1920 × 1080 and sharpens blurred images

• 4K Enhancement projects 4K images using "4K Enhancement Technology", creating ultra-high definition images (PowerLite Pro Cinema LS10000)

Full 3D projection

• Active 3D projection with RF active shutter glasses

• Supports side-by-side, top-and-bottom, and frame packing 3D formats

Flexible connectivity

• Two HDMI ports for video device or computer connections

10

• Watch both HDMI sources simultaneously with Picture-In-Picture mode

• One MHL (Mobile High-definition Link)-compatible HDMI port on the WirelessHD Transmitter for highquality audio and video from tablets and smartphones (PowerLite Pro Cinema LS9600e)

Easy-to-use setup and operation features

• Laser light source provides up to 30,000 hours of operation

• Powered lens memory function for maintaining constant height for up to five different aspect ratios

• Vertical and horizontal lens shift, and vertical keystone correction buttons for flexible projector placement

• 2.1× optical zoom ratio for improved zooming capability

Product Box Contents

Additional Components

Optional Equipment and Replacement Parts

Warranty and Registration Information

Parent topic:

Introduction to Your Projector

Product Box Contents

Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.

Make sure your projector box included all of these parts:

11

1 Projector

2 Remote control

3 Remote control batteries (two AA alkaline)

4 Power cord

5 Projector documentation CD

6 3D glasses (2 pairs)

7 WirelessHD Transmitter (PowerLite Pro Cinema LS9600e)

8 WirelessHD Transmitter AC adapter (PowerLite Pro Cinema LS9600e)

9 HDMI cable clamps (2)

Parent topic:

Projector Features

Additional Components

Depending on how you plan to use the projector, you may need to obtain the following additional components:

• To receive a component video signal, you need a compatible component cable. You can purchase one from Epson or an authorized Epson reseller.

12

• To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller.

Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.

Contact Apple for compatible adapter options.

• To receive an HDMI signal via MHL, you need an MHL-compatible device, an MHL cable, or an HDMI cable and an MHL adapter compatible with your device. Devices with an integrated MHL connector may not require a cable (PowerLite Pro Cinema LS9600e).

• To receive and view a 3D signal, you need a compatible HDMI cable. You can purchase one from

Epson or an authorized Epson reseller. If your video source is a 3D Blu-ray disc, you also need a Bluray player that supports 3D playback. See your local computer or electronics dealer for purchase information.

Parent topic:

Projector Features

Optional Equipment and Replacement Parts

You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com

(U.S. sales) or epson.ca

(Canadian sales).

Epson offers the following optional accessories and replacement parts for your projector:

Option or part

Replacement air filter

RF 3D glasses (ELPGS03)

Projector ceiling mount

Belkin PureAV HDMI audio video cable, 6 ft

Belkin PureAV HDMI audio video cable, 3 ft

Belkin Pro Series VGA/SVGA cable, 10 ft

Kensington security lock

Part number

V13H134A39

V12H548006

CHF2500

AV22300-06

AV22300-03

F3H982-10

ELPSL01

In addition to the accessories listed above, 1-year and 2-year extended service plans are available.

Parent topic:

Projector Features

13

Related tasks

Replacing the Air Filter

Warranty and Registration Information

Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure that came with your projector.

In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Home Service brochure for details.

Register your product online using the projector CD or at this site: epson.com/webreg

Registering also lets you receive special updates on new accessories, products, and services.

Parent topic:

Projector Features

Notations Used in the Documentation

Follow the guidelines in these notations as you read your documentation:

Warnings must be followed carefully to avoid bodily injury.

Cautions must be observed to avoid damage to your equipment.

Notes contain important information about your projector.

Tips contain additional projection information.

Parent topic:

Introduction to Your Projector

Where to Go for Additional Information

Need quick help on using your projector? Here's where to look for help:

• epson.com/support (U.S) or epson.ca/support (Canada)

View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24 hours a day.

• If you still need help after checking this manual and the sources listed above, you can use the Epson

PrivateLine Support service to get help fast. For details, see "Where to Get Help".

Parent topic:

Introduction to Your Projector

14

Projector Part Locations

Check the projector part illustrations to learn about the parts on your projector.

Projector Parts - Front/Top

Projector Parts - Rear

Projector Parts - Interface Ports

Projector Parts - Base

Projector Parts - Control Panel and Projector Lights

Projector Parts - Remote Control

Parent topic:

Introduction to Your Projector

Projector Parts - Front/Top

1 Projector status lights

2 Control panel

3 Front adjustable foot

4 WirelessHD receiver (PowerLite Pro Cinema LS9600e)

5 Lens

6 Lens shutter

15

7 Air exhaust vents

Parent topic:

Projector Part Locations

Projector Parts - Rear

1 Remote receiver

2 Projector ports

3 Cable clamp

4 Cable cover screw holes

5 Air intake/Air filter cover

Parent topic:

Projector Part Locations

16

Projector Parts - Interface Ports

1 HDMI1 / HDMI2 ports

2 HDMI cable clamp slots (2)

3 LAN port

4 Service port

5 RS-232C port

6 PC port (VGA)

7 Component ports

8 Trigger out 1 and Trigger out 2 ports

9 Video port

Parent topic:

Projector Part Locations

17

Projector Parts - Base

1 Air intake vent

2 Screw holes for anamorphic lens

3 Adjustable front feet

4 Mounting bracket holes

5 Power inlet

Parent topic:

Projector Part Locations

18

Projector Parts - Control Panel and Projector Lights

1 Temp light

2 Laser light

3 Status light

4 Power light

5 Power button

6 Source button (cycles through the list of sources)

7 Lens button (cycles through the lens adjustment options)

8 Menu button (accesses configuration menus)

9 Directional thumbstick (push in for OK button; controls menu selection and keystone adjustment)

10 Esc button

19

Parent topic:

Projector Part Locations

Related references

Projector Light Status

Projector Parts - Remote Control

Top buttons

Left: PowerLite Pro Cinema LS10000

Right: PowerLite Pro Cinema LS9600e

1 On button (turns on projector)

2 Standby button

3 Illumination button (lights the remote control)

4 Blank button (turns off video projection)

5 P-in-P button (controls the Picture-in-Picture mode for HDMI inputs)

6 Source buttons (select specific video input sources)

7 HDMI Link control buttons (control playback and other features of connected devices that support the HDMI CEC standard)

8 HDMI Link button (displays the settings menu for HDMI Link)

20

9 Volume up/down buttons (adjust volume for devices connected via HDMI Link)

Center buttons

1 Lens button (cycles through the lens adjustment options)

2 Color Mode button (selects display modes)

3 2D/3D button (cycles between 2D and 3D modes)

4 Arrow buttons (move though on-screen options)

5 Enter button (selects options)

6 Default button (returns selected setting to default value)

7 Menu button (accesses projector menu system)

8 Esc button (cancels/exits functions)

Bottom buttons

Left: PowerLite Pro Cinema LS10000

21

Right: PowerLite Pro Cinema LS9600e

1 Memory button (accesses the Memory menu)

2 Lens 1 / Lens 2 buttons (loads a saved lens position)

3 3D Format button (changes the 3D format)

4 Frame Int button (adjusts the Frame Interpolation setting)

5 SupRes/4K button (PowerLite Pro Cinema LS10000; reduces blurring around the edges of images when viewing 3D content, or adjusts the 4K Enhancement setting for ultra-high-definition images)

Super Res button (PowerLite Pro Cinema LS9600e; reduces blurring around the edges of images)

6 Dyn Cr button (PowerLite Pro Cinema LS10000; sets Dynamic Contrast)

7 Aspect button (selects the image aspect ratio)

8 Pattern button (displays a test pattern)

9 Lens Iris button (PowerLite Pro Cinema LS10000; adjusts the contrast of the image by restricting the amount of light entering the lens)

10 RGBCMY button (PowerLite Pro Cinema LS10000; adjusts hue, saturation, and brightness for each RGBCMY color)

11 User button (PowerLite Pro Cinema LS10000; customizable for different functions)

12 WirelessHD transmitter control buttons (PowerLite Pro Cinema LS9600e; controls WirelessHD

Transmitter functions)

22

Parent topic:

Projector Part Locations

23

Setting Up the Projector

Follow the instructions in these sections to set up your projector for use.

Projector Placement

Removing and Attaching the Cable Cover

Projector Connections

Installing Batteries in the Remote Control

Projector Placement

You can place the projector on almost any flat surface to project an image.

You can also install the projector in a ceiling mount if you want to use it in a fixed location.

Keep these considerations in mind as you select a projector location:

• Place the projector on a sturdy, level surface or install it using a compatible mount.

• Leave plenty of space around and under the projector for ventilation, and do not place it on top of or next to anything that could block the vents.

• Position the projector within reach of a grounded electrical outlet or extension cord.

Projector Setup and Installation Options

Projection Distance

Parent topic:

Setting Up the Projector

Projector Setup and Installation Options

You can set up or install your projector in the following ways:

Front

24

Rear

Front Ceiling

Rear Ceiling

Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If the projector cannot be centered in front of the screen, use lens shift to reposition the image instead of using keystone correction for better image quality.

If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.

25

Parent topic:

Projector Placement

Projection Distance

The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings.

Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image. (Conversion figures may have been rounded up or down.)

4:3 Aspect Ratio Image or Screen

Screen or image size Projection distance (1) Offset from lens center Offset from lens center

Wide to Tele

(2) (3)

40 inches (101.6 cm) 53.9 to 115.7 inches

(137 to 294 cm)

9.4 inches (24 cm) 33.5 inches (85 cm)

60 inches (152.4 cm) 14.6 inches (37 cm) 50.4 inches (128 cm)

80 inches (203.2 cm)

100 inches (254 cm)

81.5 to 174.8 inches

(207 to 443 cm)

109 to 232.7 inches

(277 to 591 cm)

137 to 291.3 inches

(348 to 740 cm)

19.3 inches (49 cm)

24 inches (61 cm)

67.3 inches (171 cm)

83.9 inches (213 cm)

26

Screen or image size Projection distance (1) Offset from lens center Offset from lens center

Wide to Tele

(2) (3)

120 inches (304.8 cm) 164.6 to 350 inches

(418 to 889 cm)

28.7 inches (73 cm) 100.8 inches (256 cm)

150 inches (381 cm) 35.8 inches (91 cm) 126 inches (320 cm)

200 inches (508 cm)

205.9 to 437.8 inches

(523 to 1112 cm)

275.2 to 583.9 inches

(699 to 1483 cm)

48 inches (122 cm) 168.1 inches (427 cm)

16:9 Aspect Ratio Image or Screen

Screen or image size Projection distance (1) Offset from lens center Offset from lens center

Wide to Tele

(2) (3)

40 inches (101.6 cm) 43.7 to 94.5 inches

(111 to 240 cm)

7.9 inches (20 cm) 27.6 inches (70 cm)

60 inches (152.4 cm) 11.8 inches (30 cm) 41.3 inches (105 cm)

80 inches (203.2 cm)

66.5 to 142.1 inches

(169 to 361 cm)

89 to 189.8 inches

(226 to 482 cm)

15.7 inches (40 cm) 54.7 inches (139 cm)

19.7 inches (50 cm) 68.5 inches (174 cm) 100 inches (254 cm) 111.4 to 237.8 inches

(283 to 604 cm)

120 inches (304.8 cm) 134.3 to 285.4 inches

(341 to 725 cm)

150 inches (381 cm) 168.1 to 357.5 inches

(427 to 908 cm)

180 inches (457.2 cm) 202 to 429.1 inches

(513 to 1090 cm)

23.6 inches (60 cm)

29.5 inches (75 cm)

35.4 inches (90 cm)

82.3 inches (209 cm)

103.2 inches (262 cm)

123.6 inches (314 cm)

Parent topic:

Projector Placement

27

Removing and Attaching the Cable Cover

Before you can connect equipment to your projector, you need to remove the cable cover.

1.

Remove both of the cable cover screws (screwdriver not included).

2.

Lift off the cable cover.

28

To attach the cable cover, slide it into position and tighten the screws.

Parent topic:

Setting Up the Projector

Projector Connections

You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound.

• For video projection, connect devices such as DVD players, gaming consoles, streaming devices, digital cameras, smartphones, and tablets with compatible video output ports.

Note: To connect a smartphone or tablet, you may need to obtain an adapter that allows you to connect to the projector. This allows you to mirror your smartphone or tablet screens, watch movies, and more. Contact your device manufacturer for compatible adapter options.

• Connect any Windows or Mac computer that has a standard video output (15-pin VGA monitor) port, or HDMI port.

Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.

Connecting to Video Sources

Connecting to Computer Sources

Connecting to External Speakers

Connecting to a Trigger Out Port

Parent topic:

Setting Up the Projector

Connecting to Video Sources

Follow the instructions in these sections to connect video devices to the projector.

Connecting to an HDMI Video Source

Attaching and Removing the HDMI Cable Clip

Connecting to an MHL-Compatible Device

Connecting to a Component Video Source

Connecting to a Composite Video Source

Parent topic:

Projector Connections

29

Connecting to an HDMI Video Source

If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.

The HDMI connection provides the best image quality.

1.

Connect the HDMI cable to your video source's HDMI output port.

2.

Connect the other end to one of the projector's HDMI ports.

Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p, 720p, or higher. See your game console documentation for instructions.

You can also select the Fast Image Processing setting to reduce lag time.

Note: When an audio/video source that meets the HDMI CEC standard is connected to the projector's

HDMI port, you can use the projector's remote control to control certain features of the linked device by pressing the HDMI Link button on the remote control and setting HDMI Link to On.

Parent topic:

Connecting to Video Sources

Related tasks

Attaching and Removing the HDMI Cable Clip

Attaching and Removing the HDMI Cable Clip

You can install the HDMI cable clip that came with your projector to provide additional support to the

HDMI cable.

1.

Plug in the HDMI cable.

30

2.

Insert the end of the cable clip anchor into the cable clip slot near the HDMI port.

3.

Place the open cable clip around the HDMI cable, but don't lock it into place.

4.

Slide the cable clip onto the anchor and lock the clip onto the HDMI connector.

To remove the cable clip, open the clip and disconnect the HDMI cable. Then pinch the sides of the cable clip anchor and carefully pull it out of the cable clip slot.

Parent topic:

Connecting to Video Sources

Connecting to an MHL-Compatible Device

If you have an MHL-compatible smartphone or tablet, you can connect it to the WirelessHD transmitter using either an MHL cable or an HDMI cable with a device-compatible MHL adapter (PowerLite Pro

Cinema LS9600e). If you have a device with a built-in MHL connector, plug it directly into the HDMI 5 /

MHL (IN) port.

Note: Some connected devices may not charge when using an MHL adapter.

1.

Connect the MHL cable or adapter to your device's Micro-USB port.

2.

If you are using an MHL adapter, connect it to an MHL-compatible HDMI cable.

3.

Connect the other end of the cable to the WirelessHD transmitter's HDMI 5 / MHL (IN) port.

31

Parent topic:

Connecting to Video Sources

Related topics

Using WirelessHD

Connecting to a Component Video Source

If your video source has component video ports, you can connect it to the projector using an optional component video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable.

1.

Connect the component connectors to your video source's color-coded component video output ports, usually labeled Y, Pb, Pr or Y, Cb, Cr. If you are using an adapter, connect these connectors to your component video cable.

2.

Connect the other end to the projector's color-coded Component video input ports.

Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p, 720p, or higher. See your game console documentation for instructions.

You can also select the Fast Image Processing setting to reduce lag time.

Parent topic:

Connecting to Video Sources

Connecting to a Composite Video Source

If your video source has a composite video port, you can connect it to the projector using an optional

RCA-style video or A/V cable.

1.

Connect the cable with the yellow connector to your video source's yellow video output port.

32

2.

Connect the other end to the projector's Video port.

Parent topic:

Connecting to Video Sources

Connecting to Computer Sources

Follow the instructions in these sections to connect a computer to the projector.

Connecting to a Computer for VGA Video

Connecting to a Computer for HDMI Video

Parent topic:

Projector Connections

Connecting to a Computer for VGA Video

You can connect the projector to your computer using a VGA computer cable.

Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port.

Contact Apple for compatible adapter options.

1.

If necessary, disconnect your computer's monitor cable.

2.

Connect the VGA computer cable to your computer's monitor port.

3.

Connect the other end to a PC port on the projector.

33

4.

Tighten the screws on the VGA connector.

Parent topic:

Connecting to Computer Sources

Connecting to a Computer for HDMI Video

If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.

Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.

1.

Connect the HDMI cable to your computer's HDMI output port.

2.

Connect the other end to one of the projector's HDMI ports.

Parent topic:

Connecting to Computer Sources

Related tasks

Attaching and Removing the HDMI Cable Clip

Connecting to External Speakers

To add sound, you can connect your video source and speakers to an audio video receiver, then connect the receiver to the projector using one of the receiver's compatible video outputs (an HDMI

34

connection provides the best image quality, if available). You can also connect speakers to any video source that has its own speaker connections.

1 Video source

2 Surround sound speakers

3 Receiver

4 Video cable

Parent topic:

Projector Connections

Connecting to a Trigger Out Port

You can connect your projector to external devices such as motorized screens that support a trigger signal. When active, a 12V signal is sent to the connected device while the projector is powered on.

1.

Connect a 3.5 mm stereo mini-jack cable to the external device's trigger port. See your device's documentation for details.

35

2.

Connect the other end to one of the projector's Trigger Out ports.

3.

Activate the trigger port in the projector's Settings menu.

Parent topic:

Projector Connections

Installing Batteries in the Remote Control

The remote control uses the two AA batteries that came with the projector.

Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.

1.

Remove the battery cover.

36

2.

Insert the batteries with the + and ends facing as shown.

3.

Replace the battery cover and press it down until it clicks into place.

Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.

Parent topic:

Setting Up the Projector

Related tasks

Replacing the Remote Control Batteries

37

Using the Projector on a Network

Follow the instructions in these sections to set up your projector for use on a network.

Wired Network Monitoring and Control

Setting Up Projector Network E-Mail Alerts

Setting Up Network Monitoring

Controlling a Networked Projector Using a Web Browser

Wired Network Monitoring and Control

You can monitor, configure, and control your projector through a wired network. You can also send email alerts from the projector when a problem occurs. To do this, you connect the projector to your network, and then set up your projector and computer for network monitoring.

Connecting to a Wired Network

Selecting Wired Network Settings

Parent topic:

Using the Projector on a Network

Connecting to a Wired Network

To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network cable. To ensure proper data transmission, use a Category 5 shielded cable or better.

1.

Connect one end of the network cable to your network hub, switch, or router.

2.

Connect the other end of the cable to the projector's LAN port.

Parent topic:

Wired Network Monitoring and Control

38

Selecting Wired Network Settings

Before you can project from computers on your network, you must select the network settings for the projector using its menu system.

Note: Make sure you already connected the projector to your wired network using the LAN port.

1.

Turn on the projector.

2.

Press the Menu button.

3.

Select the Network menu and press Enter.

4.

Select Network Configuration and press Enter.

39

5.

Select the Basic menu and press Enter.

6.

Select the following basic options as necessary:

Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.

PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the

PJLink protocol for projector control.

Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web. (Default user name is EPSONWEB; default password is

admin.)

Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow buttons on the remote control to highlight characters and press Enter to select them.

40

7.

Select the Wired LAN menu and press Enter.

8.

Select IP Settings and press Enter.

9.

Select your IP Settings as necessary:

• If your network assigns addresses automatically, turn on the DHCP setting.

41

• If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet

Mask, and Gateway Address as needed. When manually entering IP Settings, you cannot use restricted IP addresses.

Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press Enter.

10. To prevent display of the IP address on the standby screen, turn off IP Address Display.

11. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.

Restricted IP Addresses

Parent topic:

Wired Network Monitoring and Control

Restricted IP Addresses

When manually entering IP Settings, you cannot use these ranges of IP addresses:

Setting

IP Address

Subnet Mask

Gateway Address

Restricted IP addresses

0.0.0.0

127.x.x.x

192.0.2.x

224.0.0.0 to 255.255.255.255

0.0.0.0

255.255.255.255

0.0.0.0

197.x.x.x

224.0.0.0 to 255.255.255.255

Parent topic:

Selecting Wired Network Settings

Setting Up Projector Network E-Mail Alerts

You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector.

1.

Press the Menu button.

42

2.

Select the Network menu and press Enter.

3.

Select Network Configuration and press Enter.

4.

Select the Mail menu and press Enter.

5.

Turn on Mail Notification.

6.

Enter the IP address for the SMTP Server option.

Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).

7.

Select a number for the SMTP server Port Number, from 1 to 65535 (default is 25).

8.

Choose an Address field, enter the e-mail address, and select the alerts you want to receive there.

Repeat for up to three addresses.

Note: Your e-mail address can be up to 64 alphanumeric characters long. You can only enter 32 characters via the projector menu. To enter more than 32 characters, use the web configuration page to enter the e-mail address.

9.

When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.

Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.

43

Network Projector E-mail Alert Messages

Parent topic:

Using the Projector on a Network

Network Projector E-mail Alert Messages

When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you receive an e-mail containing the following information:

Epson Projector on the subject line

• The name of the projector experiencing a problem

• The IP address of the affected projector

• Detailed information about the problem

Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.

Parent topic:

Setting Up Projector Network E-Mail Alerts

Setting Up Network Monitoring

Network administrators can install monitoring software on network computers so they can monitor projectors. If your network uses this software, you can set up the projector for monitoring.

1.

Press the Menu button.

2.

Select the Network menu and press Enter.

3.

Select Network Configuration and press Enter.

44

4.

Select the Others menu and press Enter.

5.

If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to allow the projector to be detected.

6.

If your network environment uses a Control4 or Control4 SDDP controller, turn on the Control4

SDDP setting to allow the projector to be detected (PowerLite Pro Cinema LS10000).

7.

If you are connecting to a network using Bonjour, turn on the Bonjour setting.

8.

When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.

Parent topic:

Using the Projector on a Network

Controlling a Networked Projector Using a Web Browser

Once you have connected your projector to your network, you can select projector settings and control projection using a compatible web browser. This lets you access the projector remotely.

Note: The web setup and control features support Microsoft Internet Explorer 8, 9, or 10, and Safari on networks that do not use a proxy server for connection. You cannot select all of the projector menu settings or control all projector functions using a web browser.

Note: If you set Standby Mode to Communication On, you can use a web browser to select settings and control projection even if the projector is in standby mode.

45

1.

Make sure the projector is turned on.

2.

Start your web browser on a computer or device connected to the network.

3.

Type the projector's IP address into the browser's address box and press the computer's Enter key.

Note: If you connect from a web browser on a smartphone or tablet, a screen with two options is displayed. Select remote to display the Web Remote page, or select config to display the Web

Control page.

You see the Web Control screen.

Note: You may need to log in before you see the Web Control screen. If you see a log in window, enter your user name and password. (The default user name is EPSONWEB and the default password is admin.)

4.

To select projector menu settings, select the name of the menu and follow the on-screen instructions.

5.

To control projection remotely, select the Web Remote option.

46

You see a screen like this:

1 Turns the projector on

2 Turns the projector off

3 Selects HDMI1, HDMI2, WiHD (PowerLite Pro Cinema LS9600e), 3RCA (component), Video, and PC port sources

4 Blank button control

5 Switches between 2D and 3D projection

6 Loads a saved lens position

6.

Select the icon corresponding to the projector function you want to control.

Parent topic:

Using the Projector on a Network

47

Using Basic Projector Features

Follow the instructions in these sections to use your projector's basic features.

Turning On the Projector

Turning Off the Projector

Viewing 3D Images

Selecting the Language for the Projector Menus

Adjusting the Image Height

Image Shape

Resizing the Image with the Zoom Feature

Focusing the Image with the Lens Button

Adjusting the Color Convergence (Panel Alignment)

Remote Control Operation

Selecting an Image Source

Projection Modes

Image Aspect Ratio

Color Mode

Changing the Super-resolution Setting

Changing the Super-resolution/4K Enhancement Setting

Using Picture in Picture

Turning On the Projector

Turn on the computer or video equipment you want to use before you turn on the projector so it can display the image source.

48

1.

Connect the power cord to the projector's power inlet.

2.

Plug the power cord into an electrical outlet.

Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.

3.

Press the power button on the projector or the On button on the remote control to turn on the projector.

The shutter opens and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue.

Warning: Never look into the projector lens when the laser is on. This can damage your eyes and is especially dangerous for children.

If you do not see a projected image right away, try the following:

• Turn on the connected computer or video device.

• Insert a DVD or other video media and press the play button, if necessary.

• Press the Source button on the projector to detect the video source, or press a source button on the remote control.

Parent topic:

Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

49

Turning Off the Projector

Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.

Note: Turn off this product when not in use to prolong the life of the projector. Laser life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.

Note: When using the Blank feature, the laser is still on. To turn off the laser, turn off the projector.

1.

Press the power button on the projector or the Standby button on the remote control.

The projector displays a shutdown confirmation screen.

2.

Press the power button on the projector or the Standby button on the remote control again. (To leave it on, press any other button.)

The shutter closes, the laser turns off, and the Status light turns off.

Caution: Do not turn the projector on immediately after turning it off. Turning the projector on and off frequently may shorten the life of the laser.

50

3.

To transport or store the projector, make sure the Status light is off, then unplug the power cord.

Caution: To avoid damaging the projector or laser, never unplug the power cord when the Status light is on or flashing.

Parent topic:

Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

Viewing 3D Images

You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses. You can also convert 2D images to 3D using the 2D-to-3D

Conversion setting in your projector's Signal > 3D Setup menu.

You can purchase Epson RF 3D glasses from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com

(U.S. sales) or epson.ca

(Canadian sales).

1.

Connect a 3D-compatible video device to the projector using a compatible HDMI cable.

Note: You can also connect a 3D HDMI source to the WirelessHD Transmitter (PowerLite Pro

Cinema LS9600e).

2.

Turn on the video device, then turn on the projector.

3.

Begin playback from the video device.

Note: Make sure you set the video device to play content in 3D mode.

51

4.

Press the 2D/3D button on the remote control to activate 3D mode, if necessary.

5.

Slide the power switch on the 3D glasses to the On position.

6.

Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector.

Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the status light flashes green. Slide the power switch on the glasses to the Off position and then back to the On position to resume 3D viewing.

Pairing the 3D Glasses with the Projector

Charging the 3D Glasses

3D Viewing Range

Parent topic:

Using Basic Projector Features

Related references

Input Signal Settings - Signal Menu

52

Pairing the 3D Glasses with the Projector

Pair the glasses with the projector to establish communication between them for 3D viewing.

1.

Turn on the projector.

2.

Set the image source to HDMI or WirelessHD (PowerLite Pro Cinema LS9600e).

3.

Project a 3D image.

4.

Slide the power switch on the 3D glasses to the On position.

5.

Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the glasses for at least three seconds.

The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off.

Parent topic:

Viewing 3D Images

Related tasks

Selecting an Image Source

53

Charging the 3D Glasses

Charge the glasses when the status light on the glasses flashes red to indicate a low battery.

1.

Connect the smaller end of the charging cable to the port on the bridge of the glasses.

Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable.

2.

Do one of the following:

• Plug the other end of the charging cable into a powered USB port on a computer or other device.

• Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications:

Input: 100-240V, ~0.15A, 50-60Hz

Output: 5V=1A

The glasses are fully charged when the status light on the glasses stays green.

Parent topic:

Viewing 3D Images

54

3D Viewing Range

When you view 3D images, make sure you are positioned within the viewing range shown here.

1 32 ft (10 m)

Parent topic:

Viewing 3D Images

Selecting the Language for the Projector Menus

If you want to view the projector's menus and messages in another language, you can change the

Language setting.

1.

Turn on the projector.

2.

Press the Menu button.

55

3.

Select the Settings menu and press Enter.

4.

Select the Language setting and press Enter.

5.

Select the language you want to use and press Enter.

6.

Press Menu or Esc to exit the menus.

Parent topic:

Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

Adjusting the Image Height

If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet.

1.

Turn on the projector and display an image.

56

2.

If the image is tilted, rotate the front feet to adjust their height.

3.

Use the Lens button on the remote control to adjust the position of the projected image as necessary.

If the projected image is unevenly rectangular, you need to adjust the image shape.

Adjusting the Image Position Using Lens Shift

Parent topic:

Using Basic Projector Features

Adjusting the Image Position Using Lens Shift

If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature.

Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.

1.

Turn on the projector and display an image.

57

2.

Press the Lens button on the control panel or remote control.

3.

Press the Lens button repeatedly until Adjust Lens Shift is displayed on the screen.

4.

Press the arrow buttons on the remote control or use the thumbstick on the control panel to adjust the position of the projected image as necessary.

58

1 Center of lens

2 Projected image when lens shift is set in the center

3 Maximum vertical range (V × 90%)

4 Maximum horizontal range (H × 40%)

Note: You cannot move the image to both the horizontal and vertical maximum values.

5.

When you are finished, press the Esc button on the control panel or remote control.

Note: When adjusting the image height, position the image lower than where you want it to be and then move it up. This will help prevent the image from moving down after adjustment.

Parent topic:

Adjusting the Image Height

Image Shape

You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.

Adjusting Keystone with the Control Panel

Parent topic:

Using Basic Projector Features

Adjusting Keystone with the Control Panel

You can use the projector's thumbstick on the control panel to correct the shape of an image that is unevenly rectangular on the sides.

Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use keystone correction to correct the image shape.

Note: Keystone corrections are most effective within a projection angle of 30° from top to bottom.

1.

Turn on the projector and display an image.

Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.

Note: You can also display the pattern by pressing the Pattern button on the remote control.

59

2.

Move the thumbstick on the control panel up or down to display the keystone adjustment sliders, then continue moving the thumbstick up or down to adjust the image shape.

3.

Push in the thumbstick on the control panel to set the keystone value.

After correction, your image is slightly smaller.

Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus.

Parent topic:

Image Shape

Related references

Projector Feature Settings - Settings Menu

Resizing the Image with the Zoom Feature

You can adjust the size of the projected image using the zoom feature.

Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.

1.

Turn on the projector and display an image.

60

2.

Press the Lens button on the projector's control panel or remote control.

3.

Press the Lens button repeatedly until Adjust Zoom is displayed on the screen.

4.

Press and hold the left or right arrow buttons on the projector's remote control or use the thumbstick on the control panel to resize the image.

5.

Press the Esc button on the projector's control panel or remote control when finished.

Parent topic:

Using Basic Projector Features

Focusing the Image with the Lens Button

You can adjust the sharpness of the projected image using the focus feature.

Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.

1.

Turn on the projector and display an image.

61

2.

Press the Lens button on the projector's control panel or remote control.

3.

Press the Lens button repeatedly until Adjust Focus is displayed on the screen.

4.

Press and hold the left or right arrow buttons on the projector's remote control or use the thumbstick on the control panel to focus the image.

5.

Press the Esc button on the projector's control panel or remote control when finished.

Parent topic:

Using Basic Projector Features

Adjusting the Color Convergence (Panel Alignment)

You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the red, green and blue colors) in the projected image.

Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature. The projected image should be a minimum of 60 inches

(152 cm) diagonally and the projection surface should not be colored or textured, otherwise the adjustment grids will be difficult to align.

1.

Turn on the projector.

2.

Press the Menu button.

3.

Select the Extended menu and press Enter.

62

4.

Select the Panel Alignment setting and press Enter.

5.

Select the Panel Alignment setting and press Enter.

6.

Select On and press Enter.

7.

Select the Select Color setting and choose one of the following:

R to adjust the red color convergence.

B to adjust the blue color convergence.

Note: You can only adjust the red or blue color convergence. Green is the standard color panel and cannot be adjusted.

8.

Select the Pattern Color setting and press Enter.

9.

Select the pattern you want to use and press Enter.

10. Select Start Adjustments and press Enter.

63

You see this screen:

11. Use the arrow buttons on the remote control to adjust the color alignment in the corner of the screen highlighted by the orange box.

12. Press the Enter button to move to the next corner of the screen.

13. When you are finished adjusting each corner of the screen, press Enter.

You see this screen:

64

14. Do one of the following:

• If your projector's panel alignment is now correct, select Exit and press Enter to return to the

Panel Alignment menu.

• If your projector needs additional panel alignment, select Select intersection and adjust and press Enter. Use the arrow keys on the remote control to highlight the corner of any box on the screen that is misaligned and press Enter to adjust the color convergence. Repeat this step as necessary.

Parent topic:

Using Basic Projector Features

Remote Control Operation

The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector.

Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.

Vertical

65

1 32 feet (10 m)

2 ± 30°

3 60°

Horizontal

1 32 feet (10 m)

2 ± 30°

Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.

Parent topic:

Using Basic Projector Features

66

Selecting an Image Source

If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.

1.

Make sure the connected image source you want to use is turned on.

2.

For video image sources, insert a DVD or other video media and press its play button, if necessary.

3.

Do one of the following:

• Press the Source button on the projector until you see the image from the source you want.

• Press the button for the source you want on the remote control.

67

PowerLite Pro Cinema LS9600e

1 HDMI port sources

2 WirelessHD source

3 PC port (VGA) source

4 Composite video source

5 Component video source

PowerLite Pro Cinema LS10000

1 HDMI port sources

2 PC port (VGA) source

3 Composite video source

4 Component video source

68

Parent topic:

Using Basic Projector Features

Projection Modes

Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly.

Front (default setting) lets you project from a table in front of the screen.

Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.

Rear flips the image horizontally to project from behind a translucent screen.

Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind a translucent screen.

Changing the Projection Mode Using the Menus

Parent topic:

Using Basic Projector Features

Changing the Projection Mode Using the Menus

You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus.

1.

Turn on the projector and display an image.

2.

Press the Menu button.

3.

Select the Settings menu and press Enter.

69

4.

Select the Projection setting and press Enter.

5.

Select a projection mode and press Enter.

6.

Press Menu or Esc to exit the menus.

Parent topic:

Projection Modes

Related references

Projector Feature Settings - Settings Menu

Image Aspect Ratio

The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.

If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.

Changing the Image Aspect Ratio

Available Image Aspect Ratios

Parent topic:

Using Basic Projector Features

Changing the Image Aspect Ratio

You can change the aspect ratio of the displayed image to resize it.

Note: For HDMI sources, the input signal determines the image's aspect ratio.

1.

Turn on the projector and switch to the image source you want to use.

2.

Press the Aspect button on the remote control.

PowerLite Pro Cinema LS9600e

70

PowerLite Pro Cinema LS10000

A list of the available aspect ratios appears.

3.

To cycle through the available aspect ratios for your input signal, press the up or down arrow button.

4.

Press Enter to select the aspect ratio.

Parent topic:

Image Aspect Ratio

Related references

Input Signal Settings - Signal Menu

Available Image Aspect Ratios

You can select the following image aspect ratios, depending on the input signal from your image source.

Note: When the projector is in 3D mode, the aspect ratio is automatically set to Normal.

Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal.

71

Aspect ratio setting

Auto

Normal

Zoom

Full

Description

Automatically sets the aspect ratio according to the input signal.

Displays images using the full projection area and maintains the aspect ratio of the image.

Displays images using the full width of the projection area and maintains the aspect ratio of the image.

Displays images using the full width of the projection area, but does not maintain the aspect ratio.

You can also select two modes that can be used with a third-party anamorphic lens.

Aspect ratio setting

Anamorphic Wide

Horiz. Squeeze

Description

Displays CinemaScope content using an anamorphic lens.

Stretches the horizontal aspect of the input signal to project across the entire screen using an anamorphic lens.

Note: The Auto aspect ratio setting is available only for HDMI image sources.

Parent topic:

Image Aspect Ratio

Color Mode

The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types. You can select a mode designed to match your image and environment, or experiment with the available modes.

If you always want to use a particular color mode for a certain video input source, you can select it using the projector menus.

Changing the Color Mode

Available Color Modes

Adjusting the Lens Iris

Parent topic:

Using Basic Projector Features

72

Changing the Color Mode

You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment.

1.

Turn on the projector and switch to the image source you want to use.

2.

If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary.

3.

Press the Color Mode button on the remote control to change the Color Mode.

A list of available Color Modes appears.

4.

To cycle through all the available Color Modes for your input signal, press the up or down arrow button.

5.

Press Enter to select a Color Mode.

Parent topic:

Color Mode

Related references

Image Quality Settings - Image Menu

Available Color Modes

You can set the projector to use these Color Modes, depending on the input source you are using:

2D Images

Color Mode

Dynamic

Description

Best for projecting in a bright room

73

Color Mode

Living Room

Natural

THX

Cinema

Digital Cinema

(PowerLite Pro Cinema LS10000)

Adobe RGB

(PowerLite Pro Cinema LS10000)

Description

Best for projecting in a room with closed curtains

Best for projecting in a dark room. Perform color adjustment in this mode.

Uses a color mode authorized by THX Ltd.

Best for movies and concerts projected in a dark room

Uses the same color spectrum as digital cinema movie theaters

Best when projecting images using the Adobe RGB color space

3D Images

Color Mode

3D Dynamic

3D Cinema

3D THX

Description

Best for projecting in a bright room

Best for movies projected in a dark room

Color mode authorized by THX Ltd.

Parent topic:

Color Mode

Adjusting the Lens Iris

In certain color modes, you can reduce the amount of light in the projection lens and adjust the brightness of the content you project.

1.

Turn on the projector and switch to the image source you want to use.

2.

Press the Menu button.

74

3.

Select the Image menu and press Enter.

4.

Select the Lens Iris setting and press and hold the left or right arrow buttons on the projector's remote control to adjust the lens iris.

Note: Reducing the value increases the intensity of the colors in the image. The default values and settings differ based on the Color Mode settings and the zoom lens position.

5.

Press Menu or Esc to exit the menus.

Parent topic:

Color Mode

Changing the Super-resolution Setting

You can sharpen blurred images and enhance the apparent detail of an image by increasing the resolution of the image signal using the Super-resolution setting. (PowerLite Pro Cinema LS9600e).

Note: You cannot use Super-resolution when converting 2D images to 3D images, or when a computer image is displayed. When projecting 3D images, you can use this setting only with 1080p/24 Hz/frame packing signals.

1.

Turn on the projector and switch to the image source you want to use.

75

2.

Press the Super Res button on the remote control.

Note: You can also set the Super-resolution setting from the Signal menu.

A list of the setting values appears. Higher values increase the intensity of the effect.

3.

Press the left or right arrow buttons on the projector's remote control to adjust the setting.

4.

Press Menu or Esc to exit the menus.

Parent topic:

Using Basic Projector Features

Related references

Input Signal Settings - Signal Menu

Changing the Super-resolution/4K Enhancement Setting

You can set the strength of the Super-resolution/4K setting (PowerLite Pro Cinema LS10000).

If you select a Super-resolution value of 1 to 5, you can sharpen blurred images and enhance the apparent detail of an image by increasing the resolution of the image signal.

If you select a 4K Enhancement value of 4K-1 to 4k-5, you can display 4K images (3840 × 2160) using

4K Enhancement Technology with super resolution processing and create ultra high-definition images.

Note: You cannot use Super-resolution when converting 2D images to 3D images, or when a computer image is displayed. When projecting 3D images, you can use Super-resolution only with

1080p/24 Hz/frame packing signals. You cannot use 4K Enhancement when projecting 3D images.

1.

Turn on the projector and switch to the image source you want to use.

76

2.

Press the Sup Res/4K button on the remote control.

Note: You can also select the Super-resolution/4K setting in the Signal menu.

A list of the available settings appears.

3.

Press the up or down arrow buttons on the projector's remote control to select a setting.

4.

Press the Sup Res/4K button on the remote control to exit the menu.

Parent topic:

Using Basic Projector Features

Related references

Input Signal Settings - Signal Menu

Using Picture in Picture

You can use Picture in Picture mode to view two image sources simultaneously.

Note: You can only display HDMI or WirelessHD (PowerLite Pro Cinema LS9600e) video sources when

Picture in Picture mode is active.

Note: You cannot use Picture in Picture while projecting 3D or 4K images.

1.

Turn on the projector and switch to the HDMI or WirelessHD image source you want to use.

2.

Press the P-in-P button on the remote control.

PowerLite Pro Cinema LS9600e

77

PowerLite Pro Cinema LS10000

The second HDMI video source appears as a sub-screen in the corner of the image.

Note: While Picture in Picture mode is active, press the Menu button on the remote control to adjust the size and position of the sub-screen.

3.

To swap the main screen and sub-screen video sources, press and hold the P-in-P button for at least three seconds.

4.

Press the P-in-P button again to close the sub-screen and resume normal projection.

Available Picture in Picture Options

Parent topic:

Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

78

Available Picture in Picture Options

You can adjust the following options by pressing the Menu button on the remote control while Picture in

Picture mode is active:

Setting

Subscreen Size

Subscreen Position

Subscreen Source

(PowerLite Pro Cinema LS9600e)

Swap Main/Sub

Exit Picture in Picture

Description

Adjusts the size of the sub-screen

Adjusts the location where the sub-screen is displayed

Selects which source appears in the sub-screen

Switches the video source displayed on the main screen with the source displayed on the sub-screen

Closes the sub-screen and resumes normal projection

Parent topic:

Using Picture in Picture

79

Adjusting Projector Features

Follow the instructions in these sections to use your projector's feature adjustments.

Shutting Off the Picture Temporarily

Locking the Projector's Buttons

Saving Settings to Memory and Using Saved Settings

Saving the Lens Position and Using Saved Lens Positions

Shutting Off the Picture Temporarily

You can temporarily turn off the projected picture if you want to redirect your audience's attention during a presentation. Any video action continues to run, however, so you cannot resume projection at the point that you stopped it.

1.

Press the Blank button on the remote control to temporarily stop projection.

PowerLite Pro Cinema LS9600e

PowerLite Pro Cinema LS10000

80

2.

To turn the picture back on, press the Blank button again.

Parent topic:

Adjusting Projector Features

Locking the Projector's Buttons

You can lock the buttons on the projector's control panel to prevent anyone from using the projector.

Note: You can use the remote control to control the projector when the control panel buttons are locked.

1.

Press the Menu button.

2.

Select the Settings menu and press Enter.

3.

Select the Lock Setting setting and press Enter.

4.

Select one of these lock types and press Enter:

• To lock the projector's power button, select Child Lock. To turn the projector on, you must press the power button for longer than three seconds.

Note: Child Lock does not prevent the projector from turning on when the power cord is connected if the Direct Power On Setting is set to On.

• To lock all buttons except the power button, select Control Panel Lock. The lock icon is displayed on the screen if any control panel buttons are pressed while this setting is enabled.

81

You see a confirmation prompt.

5.

Select Yes and press Enter.

6.

Restart the projector for the lock settings to take effect.

Unlocking the Projector's Buttons

Parent topic:

Adjusting Projector Features

Related references

Projector Feature Settings - Settings Menu

Unlocking the Projector's Buttons

If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them.

Parent topic:

Locking the Projector's Buttons

Saving Settings to Memory and Using Saved Settings

You can save customized settings for each of your video inputs and then select the saved settings whenever you want to use them.

1.

Turn on the projector and display an image.

2.

Press the Menu button.

3.

Select the Settings menu and press Enter.

4.

Select the Memory menu and press Enter.

82

You see this screen:

5.

Select one of the following options:

Load Memory: Overwrites your current settings with saved settings

Save Memory: Saves your current settings to memory (10 memories with different names are available)

Note: A memory name that has already been used is indicated by a green mark. Saving over a previously saved memory overwrites the settings with your current settings.

Erase Memory: Erases the selected memory settings

Rename Memory: Renames a saved memory

6.

Press Esc to exit.

Parent topic:

Adjusting Projector Features

Related references

Projector Memory Options - Memory Menu

Saving the Lens Position and Using Saved Lens Positions

You can save the focus, zoom, and lens shift settings and then select the saved settings whenever you want to use them.

83

1.

Turn on the projector and display an image.

2.

Adjust the focus, zoom, and lens shift settings.

3.

Press the Menu button.

Note: You can also press the Memory button on the remote control to access the Memory menu directly.

4.

Select the Memory menu and press Enter.

You see this screen:

5.

Select one of the following options:

Load Lens Position: Overwrites your current settings with saved settings

Note: You can load the saved settings from Memory1 or Memory2 by pressing the Lens1 or

Lens2 buttons on the remote control.

Save Lens Position: Saves your current settings to memory (10 memories with different names are available)

Note: A memory name that has already been used is indicated by a green mark. Saving over a previously saved memory overwrites the settings with your current settings.

84

Erase Lens Position: Erases the selected memory settings

Rename Lens Position: Renames a saved memory (12 characters maximum)

6.

Press Esc to exit.

Parent topic:

Adjusting Projector Features

85

Using WirelessHD

You can use the included WirelessHD transmitter to wirelessly stream HD content from a video device to the projector(PowerLite Pro Cinema LS9600e).

WirelessHD Transmission Range

WirelessHD Remote Control Operation

Connecting the WirelessHD Transmitter

Viewing WirelessHD Content

Switching WirelessHD Sources

Using the WirelessHD Picture in Picture Feature

WirelessHD Transmission Range

The WirelessHD Transmitter must be placed within the distance and angles shown here. Make sure the front of the WirelessHD Transmitter faces the front of the projector.

Vertical (on surface)

1 16 feet (5 m)

2 32 feet (10 m)

3 35°

4 40°

86

Vertical (inverted on ceiling)

1 16 feet (5 m)

2 32 feet (10 m)

3 45°

4 50°

Horizontal (when WiHD Mode is set to Full)

87

1 16 feet (5 m)

2 32 feet (10 m)

3 70°

4 50°

Horizontal (when WiHD Mode is set to Dynamic)

1 16 feet (5 m)

2 32 feet (10 m)

3 85°

4 60°

When positioning the WirelessHD transmitter, note the following:

• The wireless transmission range varies depending on the placement and material of the furniture and walls. The values provided here are for your reference only.

• The projector cannot communicate through walls.

• Place the WirelessHD transmitter on a wooden shelf or other location that does not block the signal.

88

• The antennas are built into the front of the projector and the transmitter. Make sure the antennas face each other when setting up the devices.

• When checking the signal, place the projector and WirelessHD Transmitter close to each other and make sure there are no other projectors operating nearby.

• Depending on the signal strength, the image's color information may be automatically discarded to avoid any interruptions and maintain a constant connection. To avoid any deterioration in image quality, adjust the position of the transmitter so that the Reception setting is as strong as possible. If no image is being input, the Reception setting displays 0%, even if the projector and transmitter are connected.

Parent topic:

Using WirelessHD

WirelessHD Remote Control Operation

The remote control lets you control the WirelessHD transmitter from almost anywhere in the room. You must point the remote at the transmitter.

Make sure that you aim the remote control at the WirelessHD transmitter's remote receiver within the distance and angles listed here.

Vertical

1 13 feet (4 m)

2 32 feet (10 m)

3 ± 40°

89

Horizontal

1 13 feet (4 m)

2 32 feet (10 m)

3 ± 40°

Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.

Parent topic:

Using WirelessHD

Connecting the WirelessHD Transmitter

You can connect up to five HDMI input sources and one HDMI output source to your WirelessHD transmitter.

90

1.

Plug the AC adapter into the AC input port on the WirelessHD transmitter and into an electrical outlet.

2.

Connect HDMI cables to your video devices and to the HDMI input ports on the side and back of the

WirelessHD transmitter.

Note: You can connect an MHL-compatible smartphone or tablet to the HDMI 5 / MHL (IN) port on the WirelessHD Transmitter.

91

3.

To use the WirelessHD transmitter as a pass-through device to a television or other display, connect an HDMI cable to the display device and to the HDMI (OUT) port on the back of the transmitter.

Parent topic:

Using WirelessHD

Viewing WirelessHD Content

You can project content wirelessly from any device connected to the WirelessHD transmitter.

1.

Turn on the video equipment or computer you connected to the transmitter and want to project from.

2.

Press the power switch on the side of the transmitter to turn on the transmitter.

3.

Turn on the projector.

4.

Press the WirelessHD button on the remote control.

The WiHD light on the transmitter lights up and your projector displays content wirelessly.

Note: If the WirelessHD connection fails, press the Setup button on the bottom of the WirelessHD transmitter and try again.

Parent topic:

Using WirelessHD

92

Switching WirelessHD Sources

If you have connected multiple HDMI input sources to your WirelessHD transmitter, you can use the projector remote control to switch between sources.

1.

Aim the remote control at the WirelessHD transmitter.

2.

Press the Input button on the remote control or the WirelessHD transmitter.

You see this screen:

3.

Press the Input button repeatedly to highlight different input sources.

4.

When you have highlighted the source you want to switch to, release the Input button.

After a few seconds, the display switches to the highlighted source.

Parent topic:

Using WirelessHD

93

Using the WirelessHD Picture in Picture Feature

If you have connected multiple video sources to the WirelessHD transmitter, you can use the transmitter's Picture in Picture (P-in-P) feature to wirelessly project images from two separate sources at the same time. This feature is independent of any Picture-in-Picture capabilities of your projector.

1.

Make sure that the WirelessHD source is selected.

2.

Point the remote at the WirelessHD transmitter and press the P-in-P button in the WiHD Transmitter section of the remote control.

3.

Do the following to control the P-in-P display:

• Press the Input button on the remote control or the WirelessHD transmitter to change the video source displayed in the sub-screen. Keep pressing the button to cycle through the connected video devices.

• Press the Output button on the remote control or the WirelessHD transmitter to change the position of the sub-screen. The screen moves counterclockwise from corner to corner each time you press the Output button.

• Press and hold the P-in-P button on the remote control to switch the sources shown in the main display and the sub-screen.

4.

When you are finished using Picture in Picture, press the WirelessHD P-in-P button on the remote control to resume normal projection.

Parent topic:

Using WirelessHD

94

Adjusting the Menu Settings

Follow the instructions in these sections to access the projector menu system and change projector settings.

Using the Projector's Menus

Image Quality Settings - Image Menu

Input Signal Settings - Signal Menu

Projector Feature Settings - Settings Menu

Projector Memory Options - Memory Menu

Projector Information Display - Info Menu

Projector Reset Options - Reset Menu

Using the Projector's Menus

You can use the projector's menus to adjust the settings that control how your projector works. The projector displays the menus on the screen.

1.

Press the Menu button on the control panel or remote control.

95

You see the menu screen displaying the Image menu settings.

2.

Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right.

Note: The available settings depend on the current input source.

3.

To change settings in the displayed menu, press Enter.

4.

Press the up or down arrow button to move through the settings.

5.

Change the settings using the buttons listed on the bottom of the menu screens.

6.

To return all the menu settings to their default values, select Reset.

7.

When you finish changing settings on a menu, press Esc.

8.

Press Menu or Esc to exit the menus.

Parent topic:

Adjusting the Menu Settings

96

Image Quality Settings - Image Menu

Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source.

To change settings for an input source, make sure the source is connected and select that source.

Setting

Color Mode

Options

Dynamic

Living Room

Natural

THX

Cinema

Digital Cinema (PowerLite Pro

Cinema LS10000)

Adobe RGB (PowerLite Pro

Cinema LS10000)

3D Dynamic

3D Cinema

3D THX

Description

Adjusts the vividness of image colors for various image types and environments

Not all Color Modes are available on all models.

97

Setting

Brightness

Contrast

Color Saturation

Options

Varying levels available

Varying levels available

Varying levels available

Tint Varying levels available

Sharpness Standard:

Varying levels available

Advanced:

Thin Line Enhancement

Thick Line Enhancement

Vert. Line Enhancement

Horiz. Line Enhancement

Color Temp. (color temperature) –3 to 6 (10 increments) or

5000K to 10000K

Skin Tone Varying levels available

Description

Lightens or darkens the overall image

Adjusts the difference between light and dark areas of the image

Adjusts the intensity of the image colors.

Adjusts the balance of green to magenta tones in the image.

Adjusts the sharpness or softness of image details

Sets the overall color tone; higher values tint the image blue and lower values tint the image red; for certain color modes, the settings change to 5000K -

10000K

Makes fine adjustments to the color tone; higher values tint the image green and lower values tint the image red

98

Setting

Advanced

Power Consumption

Options

Gamma

RGB

RGBCMY

EPSON Super White

Color Gamut

High or Extra Bright

Medium or Normal

ECO

Description

Selects various detailed color settings

Gamma: adjusts the gamma levels of the image. Select

Customized to adjust the gamma while viewing the image or a graph.

RGB: adjusts the dark areas

(Offset) and bright areas (Gain) of the image for each color

RGBCMY: adjusts the hue, saturation, and brightness for each color

EPSON Super White: reduces over-exposure of whites in your image; can be set only when

Color Mode is set to certain color modes

Color Gamut: selects the color gamut that matches the current video standard (HDTV, EBU, or

SMPTE-C)

Selects the brightness mode of the projector

High: sets maximum brightness

Medium: sets reduced brightness

ECO: reduces brightness and fan noise, and saves power and laser life

If you set the Color Mode to THX, the options change to Extra

Bright, Normal, and ECO.

99

Setting

Dynamic Contrast

Lens Iris

Options

Off

Normal

High Speed

Varying levels available

Description

Adjusts the luminance of the image to improve contrast by tracking changes in image brightness

Adjusts the contrast of the image by controlling the amount of light entering the lens

Note: The Brightness setting does not affect laser brightness. To change the laser brightness mode, use the Power Consumption setting.

Parent topic:

Adjusting the Menu Settings

Related tasks

Changing the Color Mode

Adjusting the Lens Iris

Input Signal Settings - Signal Menu

Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.

100

To change settings for an input source, make sure the source is connected and select that source.

Setting

3D Setup

Options

3D Display

2D-to-3D Conversion

3D Format

3D Depth

Diagonal Screen Size

Inverse 3D Glasses

3D Viewing Notice

Description

Selects various 3D options for 3D image sources

3D Display: enables 3D mode

2D-to-3D Conversion: converts

2D images to 3D

Note: When using 2D-to-3D

Conversion, set 3D Format to

Auto or 2D.

Aspect

Tracking

See the list of available aspect ratios

Varying levels available

3D Format: selects the 3D format

3D Depth: sets the depth for the

3D image

Diagonal Screen Size: selects the actual size of the screen to maximize the 3D effect

Inverse 3D Glasses: reverses the images projected for the left and right eyes (enable only if 3D images do not display correctly)

3D Viewing Notice: enables the viewing notice displayed when using 3D mode

Sets the aspect ratio (width-toheight ratio) for the selected input source

Adjusts signal to eliminate vertical stripes in computer images from the PC input port

101

Setting

Sync.

Position

Deinterlacing

Motion Detection

Frame Interpolation

Super-resolution (PowerLite

Pro Cinema LS9600e)

Options

Varying levels available

Up, down, left, right

Off

Video

Film/Auto

1 to 5

Off

Low

Normal

High

0 to 5

Description

Adjusts signal to eliminate fuzziness or flickering in computer images; for best results, adjust the Tracking setting before adjusting the Sync setting to improve the accuracy of the adjustments.

Adjusts the image location on the screen

Sets whether to convert interlaced-to-progressive signals for certain video image types

Off: for fast-moving video images

Video: for most video images

Film/Auto: for movies, computer graphics, and animation

Selects how the image is converted to a progressive signal; if you experience problems with still image quality or flickering video, select a lower setting for still images or a higher setting for fast-moving video content.)

Smooths fast moving video by comparing consecutive frames and inserting an intermediate frame between them

Sharpens blurred images resulting from increasing resolution

102

Setting Options

Super-resolution/4K (PowerLite Off

Pro Cinema LS10000)

1 to 5

4K-1 to 4K-5

Detail Enhancement

Auto Setup

Range

Strength

On

Off

Description

Sharpens blurred images resulting from increasing resolution

Super-resolution (1 to 5); reduces blurring when the image resolution is increased to

1920 × 1080

4K Enhancement (4K-1 to 4K-5); projects 4K images

(3840 × 2160), employing superresolution processing to create ultra-high-definition video images

Cannot be set when a 4K or computer image is selected

Enhances details to create clear outlines;

Range: higher settings increase the affected area around the outline

Strength: higher settings create a stronger effect

Automatically optimizes computer image quality

103

Setting

Advanced

Options

Noise Reduction

Setup Level

Overscan

HDMI Video Range

Image Processing

Description

Noise Reduction: reduces flickering in analog images in three levels

Setup Level: adjusts the level at which dark areas of the image are rendered black; leave this setting at 0% for most video equipment; check your video equipment specifications to verify the correct setting

Overscan: changes the projected image ratio to make the edges visible by a selectable percentage or automatically

HDMI Video Range: sets the video range to match the setting of the device connected to the

HDMI input port

Image Processing: adjusts how images are processed; select

Fast to display images quicker; select Fine to display images in higher quality

Note: The Reset setting does not reset the Diagonal Screen Size, 3D Viewing Notice, Aspect, and

Image Processing settings.

Parent topic:

Adjusting the Menu Settings

Related concepts

Image Aspect Ratio

Related tasks

Changing the Super-resolution Setting

Changing the Super-resolution/4K Enhancement Setting

104

Projector Feature Settings - Settings Menu

Options on the Settings menu let you customize various projector features.

Setting

Keystone

Options

Varying levels available

Description

Adjusts vertical image shape to rectangular

105

Setting

HDMI Link

Options

Device Connections

HDMI Link

Power On Link

Power Off Link

Description

Adjusts the HDMI Link options that allow the projector remote to control HDMI-connected devices that support the CEC standard

Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports

HDMI Link: enables or disables the HDMI Link function

Power On Link: controls what happens when you turn on the projector or a linked device

PJ -> Device or Bidirectional: turns on the linked device when the projector is turned on

Device -> PJ or Bidirectional: turns on the projector when the linked device is turned on

Power Off Link: controls whether linked devices are turned off when the projector is turned off

106

Setting

WirelessHD

(PowerLite Pro Cinema

LS9600e)

Options

Device Connections

WirelessHD

Reception

WiHD Mode

Lock Setting

Projection

Lens Lock

Child Lock

Control Panel Lock

Description

Device Connections: displays a list of available WirelessHD devices

WirelessHD: controls whether the projector receives

WirelessHD signals

Reception: displays the strength of the WirelessHD signal

WiHD Mode: adjusts the

WirelessHD signal strength and range

Full: uses the maximum video bandwidth at all times

Dynamic: provides extended signal range while adjusting the video bandwidth in real time; if your WirelessHD signal is weak, try changing the

WiHD Mode to Dynamic

Controls projector button locking to secure the projector

Lens Lock: locks the focus, zoom, and lens shift settings

Child Lock: locks the power button

Control Panel Lock: locks all buttons except the power button

Selects the way the projector faces the screen so the image is oriented correctly

Front

Front/Ceiling

Rear

Rear/Ceiling

107

Setting

User Button

(PowerLite Pro Cinema

LS10000)

Picture in Picture

Options

2D-to-3D Conversion

3D Depth

Description

Assigns a menu option to the

User button on the remote control for one-touch access

Inverse 3D Glasses

Power Consumption

Detail Enhancement

Info

See the list of available Picture in Adjusts the size and location of

Picture options the sub-screen, swaps sources and exits Picture in Picture mode

108

Setting

Operation

Options

Direct Power On

Sleep Mode

Illumination

Trigger Out

High Altitude Mode

Lens Adjustment Mode

Description

Selects various operation options

Direct Power On: lets you turn on the projector without pressing the power button

Sleep Mode: automatically places the projector in standby mode after an interval of inactivity

Illumination: turns off the lights on the projector

Trigger Out: outputs a DC 12V signal from the 3.5 mm mini-jack

Trigger Out 1 and Trigger Out 2 ports whenever the projector is turned on; the Anamorphic

Wide option outputs voltage to both Trigger Out ports when

Aspect is set to Anamorphic

Wide or Horiz. Squeeze

High Altitude Mode: regulates the projector’s operating temperature at altitudes above

4921 feet (1500 m)

Lens Adjustment Mode: adjusts the amount of lens movement for the focus, zoom, and lens shift adjustments when pressing the arrow buttons; lower numbers reduce the amount of movement, and higher numbers increase the amount of movement per button press

109

Setting

Display

Input Signal

Options

Menu Position

Menu Color

Messages

Display Background

Startup Screen

Standby Confirmation

Video Signal

Component

Description

Selects various display options

Menu Position: adjusts the location where the menu is displayed

Menu Color: selects the color of the menu

Messages: controls whether messages are displayed on the screen

Display Background: selects the screen color or logo to display when no signal is received

Startup Screen: controls whether a special screen appears when the projector starts up

Standby Confirmation: displays a confirmation message after pressing the Standby button on the remote control

Selects the input signals for certain ports

Video Signal: specifies the signal type from input sources connected to the Video port or select Auto to detect the signal automatically

Component: specifies the signal type from input sources connected to the Component port or select Auto to detect the signal automatically

110

Setting

Panel Alignment

Language

Options

Panel Alignment

Select Color

Pattern Color

Start Adjustments

Various languages available

Description

Corrects color misalignment in the projected image

Panel Alignment: enables adjustments for color convergence (the alignment of the red and blue colors in the projected image)

Select Color: specifies the color convergence to correct

Pattern Color: specifies the color pattern used during panel alignment

Start Adjustments: starts the

Panel Alignment feature

Selects the language for projector menu and message displays (not changed by Reset option)

Note: The Reset setting does not reset the following settings: Power On Link, Power Off Link,

Projection, User Button, Standby Mode, High Altitude Mode, Component, or Language.

Parent topic:

Adjusting the Menu Settings

Related concepts

Projector Placement

Related tasks

Adjusting Keystone with the Control Panel

Locking the Projector's Buttons

Using Picture in Picture

Related topics

Using WirelessHD

111

Projector Memory Options - Memory Menu

Your projector comes with 10 memory locations where you can save customized settings to obtain the best picture quality for each of your video inputs.

Setting

Load Memory

Save Memory

Erase Memory

Rename Memory

Load Lens Position

Save Lens Position

Erase Lens Position

Description

Displays the list of customized settings entries that you have created; select an entry and press Enter on the remote control to load it

Saves the current projector settings to the projector's memory

Displays the list of customized settings entries that you have created; select an entry and press Enter on the remote control to erase it

Displays the list of customized settings entries that you have created; select an entry and press Enter on the remote control to rename it

Loads lens adjustment values saved with the Save Lens Position setting

Saves the focus, zoom, and lens shift adjustments as a lens position entry

Deletes the saved lens position entry

112

Setting

Rename Lens Position

Description

Renames a saved lens position entry

Parent topic:

Adjusting the Menu Settings

Related tasks

Saving Settings to Memory and Using Saved Settings

Projector Information Display - Info Menu

You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu.

Note: Available settings depend on the current input source. The laser usage timer does not register any hours until you have used the laser for at least 10 hours.

Information item

Operation Hours

Source

Input Signal

Resolution

Description

Displays the number of hours (H) the laser has been used

Displays the name of the port to which the current input source is connected

Displays the input signal setting of the current input source

Displays the resolution of the current input source

113

Information item

Scan Mode

Refresh Rate

3D Format

Sync Info

Deep Color

Video Signal

Status

Serial Number

Version

Description

Displays the scan mode

Displays the refresh rate of the current input source

Displays the 3D format of the signal (Frame Packing, Side-by-Side, or Top and Bottom)

Displays information that may be needed by a service technician

Displays Deep Color bit depth information

Displays the video signal format of the current input source

Displays information about projector problems that may be needed by a service technician

Displays the projector's serial number

Displays the projector's firmware version

Parent topic:

Adjusting the Menu Settings

Projector Reset Options - Reset Menu

You can reset most of the projector settings to their default values using the Reset All option on the

Reset menu.

You can reset all memory entries using the Reset Memory option.

You can erase all saved lens position entries using the Reset Lens Position option.

114

You cannot reset the following settings using the Reset All option:

Input Signal - Component

Panel Alignment

Language

• Memory settings

• Saved lens position settings

Operation Hours

Parent topic:

Adjusting the Menu Settings

115

Maintaining and Transporting the Projector

Follow the instructions in these sections to maintain your projector and transport it from place to place.

Projector Maintenance

Transporting the Projector

Projector Maintenance

Your projector needs little maintenance to keep working at its best.

You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.

The only parts you should replace are the air filter and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson servicer.

This projector uses a sealed laser light source which does not need servicing and cannot be replaced.

Warning: Before cleaning any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except as specifically explained in this manual. Dangerous electrical voltages in the projector can injure you severely.

Warning: Do not try to service this product yourself, except as specifically explained in this manual.

Refer all other servicing to qualified servicers.

Cleaning the Lens

Cleaning the 3D Glasses

Cleaning the Projector Case

Air Filter and Vent Maintenance

Replacing the Remote Control Batteries

Parent topic:

Maintaining and Transporting the Projector

Cleaning the Lens

Do not touch the projector lens. If the lens needs to be cleaned, contact Epson support.

Parent topic:

Projector Maintenance

116

Cleaning the 3D Glasses

To remove dust, dirt, smudges, or fingerprints from the glasses, use a lint-free cloth.

Note: Unplug any charging cables from the glasses before cleaning them.

Caution: Do not use paper towels or any other abrasive materials to clean the glasses.

Parent topic:

Projector Maintenance

Cleaning the Projector Case

Before cleaning the projector case, turn off the projector and unplug the power cord.

• To remove dust or dirt, use a soft, dry, lint-free cloth.

• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector.

Caution: Do not use wax, alcohol, benzine, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a residue.

Parent topic:

Projector Maintenance

Air Filter and Vent Maintenance

Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance simple. Filter maintenance intervals will depend on the environment.

117

If regular maintenance is not performed, your Epson projector will notify you when the temperature inside the projector has reached a high level. Do not wait until this warning appears to maintain your projector filter as prolonged exposure to high temperatures may reduce the life of your projector or laser.

Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector's Limited Warranty.

Cleaning the Air Filter

Replacing the Air Filter

Parent topic:

Projector Maintenance

Related references

Projector Light Status

Cleaning the Air Filter

You need to clean the projector's air filter in the following situations:

• The filter or vents get dusty.

• You see a message telling you to clean it.

1.

Turn off the projector and unplug the power cord.

2.

Remove the cable cover if it is attached.

118

3.

Press and hold the tab on the air filter cover, and pull to open the cover.

119

4.

Pull the air filter out of the projector.

5.

Tap each side of the air filter 4 to 5 times to shake off any excess dust.

Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas.

120

6.

Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.

Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.

7.

Place the air filter back in the projector as shown.

121

8.

Close the air filter cover and press until it clicks into place.

9.

Replace the cable cover if necessary.

Parent topic:

Air Filter and Vent Maintenance

Replacing the Air Filter

You need to replace the air filter in the following situations:

• After cleaning the air filter, you see a message telling you to clean or replace it

• The air filter is torn or damaged

You can replace the air filter while the projector is mounted to the ceiling or placed on a table.

1.

Turn off the projector and unplug the power cord.

2.

Remove the cable cover, if necessary.

122

3.

Press and hold the tab on the air filter cover, and pull to open the cover.

123

4.

Pull the air filter out of the projector.

Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.

5.

Place the new air filter in the projector as shown.

124

6.

Close the air filter cover and press until it clicks into place.

7.

Replace the cable cover, if necessary.

Parent topic:

Air Filter and Vent Maintenance

Related references

Optional Equipment and Replacement Parts

Replacing the Remote Control Batteries

The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out.

Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.

125

1.

Remove the battery cover as shown.

2.

Remove the old batteries.

Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury.

3.

Insert the batteries with the + and ends facing as shown.

126

4.

Replace the battery cover and press it down until it clicks into place.

Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.

Parent topic:

Projector Maintenance

Transporting the Projector

The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely:

• Remove any equipment connected to the projector.

• When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile."

• When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box "Fragile."

Note: Epson shall not be liable for any damages incurred during transportation.

Parent topic:

Maintaining and Transporting the Projector

127

Solving Problems

Check the solutions in these sections if you have any problems using the projector.

Projection Problem Tips

Projector Light Status

Solving Image Problems

Solving Projector or Remote Control Operation Problems

Solving Network Problems

Where to Get Help

Projection Problem Tips

If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.

If this does not solve the problem, check the following:

• The lights on the projector may indicate what the problem is.

• The solutions in this manual can help you solve many problems.

If none of these solutions help, you can contact Epson for technical support.

Parent topic:

Solving Problems

Projector Light Status

The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.

128

1 Temp light

2 Laser light

3 Status light

4 Power light

Power light

Blue

Status light

Blue

Laser light Temp light

Off Off

Status and solution

Normal operation or standby (with

Communication On)

129

Power light

Blue

Off

Blue

Flashing blue

Off

Status light Laser light Temp light

Flashing blue Off Off

Off

Off

Varies

Flashing blue

Off

Off

Varies

Off

Off

Off

Flashing orange

Orange

Status and solution

Warming up; wait for an image to appear or

Shutting down; when the Status light stops flashing, you can unplug the projector

Standby or sleep mode

Standby (with Communication On) or WirelessHD standby (PowerLite

Pro Cinema LS9600e)

Projector is too hot

• Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects

• Clean or replace the air filter

• Make sure the environmental temperature is not too hot

Projector has overheated and turned off; leave it turned off until it cools down, then do the following:

• Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects

• Clean or replace the air filter

• If the problem persists, unplug the projector and contact Epson for help

130

Power light

Off

Off

Off

Off

Off

Status light

Flashing blue

Flashing blue

Flashing blue

Flashing blue

Laser light Temp light

Orange

Off

Flashing orange

Orange

Flashing blue Flashing orange

Flashing blue Flashing blue Flashing orange

Off

Flashing orange

Flashing orange

Orange

Off

Flashing orange

Status and solution

Laser has a problem or failed to turn on

• Clean or replace the air filter

• If operating the projector at high altitude, turn on High Altitude

Mode

• If the problem persists, unplug the projector and contact Epson for help

A fan or sensor has a problem; turn the projector off, unplug it, and contact Epson for help

Cinema filter, static iris, or lens shutter error; turn the projector off, unplug it, and contact Epson for help

Laser driver error; turn the projector off, unplug it, and contact Epson for help

Internal projector error; turn the projector off, unplug it, and contact

Epson for help

Fatal error; turn the projector off, unplug it, and contact Epson for help

Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help.

Parent topic:

Solving Problems

Related tasks

Cleaning the Air Filter

Replacing the Air Filter

131

Solving Image Problems

Check the solutions in these sections if you have any problems with projected images.

Solutions When No Image Appears

Solutions When "No Signal" Message Appears

Solutions When "Not Supported" Message Appears

Solutions When Only a Partial Image Appears

Solutions When the Image is Not Rectangular

Solutions When the Image Contains Noise or Static

Solutions When the Image is Fuzzy or Blurry

Solutions When the Image Brightness or Colors are Incorrect

Solutions to Panel Alignment Problems

Solutions When a 3D Image Does Not Display Correctly

Solutions When a WirelessHD Source Does Not Display Correctly

Parent topic:

Solving Problems

Related references

Projector Light Status

Solutions When No Image Appears

If no image appears, try the following solutions:

• Press the Blank button on the remote control to see if the image was temporarily turned off.

• Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.

• Press the projector's power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver.

• Press the Menu button. If the projector menu is able to display, there may be a problem with the connected video source, cable connection, or port.

• Check the settings on the Signal menu to make sure they are correct for the current video source.

• Check the Display setting to make sure Messages is set to On.

• If the projector does not respond when you press the control panel buttons, the buttons may be locked. Unlock the buttons.

• For images projected with Windows Media Center, reduce the screen size from full screen mode.

132

• For images projected from applications using Windows DirectX, turn off DirectX functions.

Parent topic:

Solving Image Problems

Related references

Input Signal Settings - Signal Menu

Solutions When "No Signal" Message Appears

If the "No Signal" message appears, try the following solutions:

• Press the Source button on the projector repeatedly to cycle through the available sources. Wait a few seconds for an image to appear.

• Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary.

• Check the connection from the projector to your video sources.

• If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.

• If necessary, turn the projector and the connected computer or video source off and then on again.

• If the other solutions do not solve the problem, reset all of the settings using the Reset menu.

Displaying From a PC Laptop

Displaying From a Mac Laptop

Parent topic:

Solving Image Problems

Related tasks

Selecting an Image Source

Displaying From a PC Laptop

If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor.

1.

Hold down the laptop's Fn key and press the key labelled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear.

2.

To display on both the laptop's monitor and the projector, try pressing the same keys again.

3.

If the same image is not displayed by the laptop and projector, check the Windows Display utility to make sure the external monitor port is enabled and extended desktop mode is disabled. (See your computer or Windows manual for instructions.)

4.

If necessary, check your video card settings and set the multiple display option to Mirror or

Duplicate.

133

Parent topic:

Solutions When "No Signal" Message Appears

Displaying From a Mac Laptop

If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.)

1.

Open the System Preferences utility and select Displays.

2.

Click the Arrangement tab.

3.

Select the Mirror Displays checkbox.

Parent topic:

Solutions When "No Signal" Message Appears

Solutions When "Not Supported" Message Appears

If the "Not Supported" message appears, try the following solutions:

• Make sure the correct input signal is selected on the Settings menu.

• Make sure the computer's display resolution does not exceed the projector's resolution and frequency limit. If necessary, select a different display resolution for your computer. (See your computer manual for details.)

• As a test, try setting the computer's display resolution to the lowest possible setting, and then gradually increase it as necessary.

Parent topic:

Solving Image Problems

Related references

Projector Feature Settings - Settings Menu

Solutions When Only a Partial Image Appears

If only a partial computer image appears, try the following solutions:

• Press the Aspect button on the remote control to select a different image aspect ratio.

• Check the cables connecting the computer or video source to the projector. Try connecting different cables.

• Check your computer display settings to disable dual display and set the resolution within the projector's limits. (See your computer manual for details.)

• Check the resolution assigned to your presentation files to see if they are created for a different resolution than you are projecting in. (See your software help for details.)

Parent topic:

Solving Image Problems

134

Related tasks

Changing the Image Aspect Ratio

Solutions When the Image is Not Rectangular

If the projected image is not evenly rectangular, try the following solutions:

• Place the projector directly in front of the center of the screen, facing it squarely, if possible.

• Adjust the image shape using the Keystone menu setting.

Parent topic:

Solving Image Problems

Related tasks

Adjusting Keystone with the Control Panel

Solutions When the Image Contains Noise or Static

If the projected image seems to contain electronic interference (noise) or static, try the following solutions:

• Check the cables connecting your computer or video source to the projector. They should be:

• Separated from the power cord to prevent interference

• Securely connected at both ends

• Not connected to an extension cable

• No longer than 10 feet (3 m) for VGA/computer cables or 24 feet (7.3 m) for HDMI cables

• Check the settings on the projector's Signal menu to make sure they match the video source.

• Select a computer video resolution and refresh rate that are compatible with the projector.

• If you are projecting from a computer, display a uniformly patterned image on the screen and manually adjust the Tracking and Sync settings.

• If you adjusted the image shape using the projector controls, try decreasing the Sharpness setting to improve image quality.

• If you connected an extension power cable, try projecting without it to see if it caused interference in the signal.

Parent topic:

Solving Image Problems

Related references

Input Signal Settings - Signal Menu

Image Quality Settings - Image Menu

135

Solutions When the Image is Fuzzy or Blurry

If the projected image is fuzzy or blurry, try the following solutions:

• Adjust the image focus.

• Check the lens for condensation.

Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it.

• Position the projector close enough to the screen, and directly in front of it.

• If you are projecting from a computer, use a lower resolution.

• Turn off any keystone correction and disable the Quick Corner setting.

Parent topic:

Solving Image Problems

Related references

Image Quality Settings - Image Menu

Related tasks

Focusing the Image with the Lens Button

Solutions When the Image Brightness or Colors are Incorrect

If the projected image is too dark or light, or the colors are incorrect, try the following solutions:

• Press the Color Mode button on the remote control to try different color modes for the image and environment.

• Check your video source settings.

• Adjust the available settings on the Image menu for the current input source, such as Brightness,

Contrast, Tint, Advanced, and Color Saturation.

• Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables.

• If you are using the ECO Power Consumption setting, try selecting High in the projector's menus.

• Position the projector close enough to the screen.

Parent topic:

Solving Image Problems

Related references

Image Quality Settings - Image Menu

136

Projector Feature Settings - Settings Menu

Related tasks

Changing the Color Mode

Solutions to Panel Alignment Problems

If the panel alignment does not result in a satisfactory picture, try the following solutions:

• Make sure the Projection setting matches the installation position.

• Make sure the projection surface is not colored or textured. Project on a white surface with no texture.

• Leave the projector on for a while before making adjustments to the panel alignment.

• The projected image size should be at least 60 inches (152 cm).

• If the image contains too much magenta, adjust the red and blue panels.

• If the pattern lines look fuzzy or out of focus, adjust the focus before shifting the panel alignment.

Parent topic:

Solving Image Problems

Related tasks

Focusing the Image with the Lens Button

Changing the Projection Mode Using the Menus

Adjusting the Color Convergence (Panel Alignment)

Solutions When a 3D Image Does Not Display Correctly

If a 3D image does not display correctly, try the following solutions:

• Press the 2D/3D button on the remote control to switch to 3D mode, if necessary. You can also activate 3D mode by setting the 3D Display setting on the Signal menu to On.

• Make sure your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information.

• Make sure you are using an HDMI cable that supports 3D signals.

• Make sure you selected the correct 3D Format setting on the Signal menu. Normally this should be set to Auto, but in some cases you may need to select a different setting to match the 3D signal from your video device.

• Make sure you are using RF 3D active shutter glasses. You can purchase them from Epson.

• Make sure your 3D glasses are turned on and fully charged. If the glasses have entered standby mode, slide the power switch on the glasses to the Off position and then back to the On position.

137

• Make sure your 3D glasses are paired with the projector.

• Adjust the 3D Depth setting on the Signal menu.

• Make sure you are within the 3D viewing range.

• Avoid using the projector near wireless networks, microwave ovens, 2.4 GHz cordless phones, or other devices that use the 2.4 GHz frequency band. These devices can interfere with the signal between the projector and the 3D glasses.

• If the other solutions do not not solve the problem, change the Inverse 3D Glasses setting on the

Signal menu. Return the setting to its original value if changing it does not solve the problem.

Parent topic:

Solving Image Problems

Related references

Input Signal Settings - Signal Menu

Related tasks

Viewing 3D Images

Solutions When a WirelessHD Source Does Not Display Correctly

If a WirelessHD source does not display correctly, try the following solutions:

• Make sure WirelessHD is selected as the image source on the projector.

• Open the WirelessHD reception monitor in the Settings menu and check the strength of the

WirelessHD signal. If the signal is weak, you may need to move the transmitter closer to the projector or remove any large objects located between the transmitter and the projector.

• Make sure that your projector is connected to the correct WirelessHD device. It can take up to 30 seconds for a signal to sync and appear after connecting.

• You may need to reset the WirelessHD connection. Turn off both the WirelessHD transmitter and the projector. Start playback on your video device, then turn on the WirelessHD transmitter and the projector. Wait 10 seconds, then press the Setup button on the bottom of the transmitter.

• Make sure the WirelessHD transmitter is within 32 feet (10 m) of the projector, isn’t obstructed by any large objects, and is not placed on a metal surface.

• If the green and orange lights on the transmitter are flashing, the unit may be overheating. Make sure the vents on the back of the transmitter are not blocked and that the room temperature does not exceed 95 °F (35 °C).

• If you are viewing wireless content, make sure that the WiHD light on the transmitter is on. If it is off, press the Output button on the remote control or transmitter.

Parent topic:

Solving Image Problems

138

Solving Projector or Remote Control Operation Problems

Check the solutions in these sections if you have problems operating the projector or remote control.

Solutions to Projector Power or Shut-Off Problems

Solutions to Problems with the Remote Control

Parent topic:

Solving Problems

Solutions to Projector Power or Shut-Off Problems

If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions:

• Make sure the power cord is securely connected to the projector and to a working electrical outlet.

• The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector.

• If the projector's laser shuts off unexpectedly, it may have entered standby mode after a period of inactivity. Press the power button to wake the projector.

• If the projector's laser shuts off, the Status light is flashing blue, and the Temp light is orange, the projector has overheated and shut off. Check the solutions for this light status.

• If the power button on the remote control does not turn on the projector, check its batteries and make sure the Remote Receiver setting is turned on in the projector's menu, if available.

• Make sure Sleep Mode is not enabled.

• The power cord may be defective. Disconnect the cord and contact Epson.

Parent topic:

Solving Projector or Remote Control Operation Problems

Related references

Projector Feature Settings - Settings Menu

Projector Light Status

Related tasks

Unlocking the Projector's Buttons

Solutions to Problems with the Remote Control

If the projector does not respond to remote control commands, try the following solutions:

• Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries.

139

• Make sure you are operating the remote control within the reception angle and range of the projector.

• Make sure the projector is not warming up or shutting down.

• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release the button to wake the remote control up.

• Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the projector's remote receivers. Dim the lights or move the projector away from the sun or interfering equipment.

• If available, turn off one of the remote receivers in the projector's menu system, or check if all the remote receivers were turned off.

• If you assigned an ID number to the remote control to operate multiple projectors, you may need to check or change the ID setting (feature not available with all projectors).

• If you lose the remote control, you can order another one from Epson.

Parent topic:

Solving Projector or Remote Control Operation Problems

Related references

Remote Control Operation

Related tasks

Replacing the Remote Control Batteries

Solving Network Problems

Check the solutions in these sections if you have problems using the projector on a network.

Solutions When Network Alert E-Mails are Not Received

Solutions When You Cannot Access the Projector Through the Web

Parent topic:

Solving Problems

Solutions When Network Alert E-Mails are Not Received

If you do not receive an e-mail alerting you to problems with a projector over the network, try the following solutions:

• Make sure the projector is turned on and connected to the network correctly. (If an error shut down the projector, it cannot send an e-mail.)

• Make sure you set up the projector e-mail alert settings correctly on the projector's network Mail menu or in the network software.

Parent topic:

Solving Network Problems

140

Related tasks

Setting Up Projector Network E-Mail Alerts

Solutions When You Cannot Access the Projector Through the Web

If you are unable to access the projector through a web browser, make sure you are using the correct ID and password, which are case sensitive.

• For the user ID, enter EPSONWEB. (You cannot change the user ID.)

• For the password, enter the password set in the projector's Network menu. The default password is

admin.

• Make sure you have access to the network the projector is on.

Note: The user ID and password are case sensitive.

Parent topic:

Solving Network Problems

Where to Get Help

If you need to contact Epson for technical support services, use the following support options.

Internet Support

Visit Epson's support website at epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to common problems with your projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562)

276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time,

Saturday.

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Before you call, have the following information ready:

• Product name

• Product serial number (located on the bottom or rear of the projector, or in the menu system)

141

• Proof of purchase (such as a store receipt) and date of purchase

• Computer or video configuration

• Description of the problem

Purchase Supplies and Accessories

You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com

(U.S. sales) or epson.ca

(Canadian sales).

To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).

Parent topic:

Solving Problems

142

Technical Specifications

These sections list the technical specifications of your projector.

General Projector Specifications

Projector Light Source Specifications

Remote Control Specifications

Projector Dimension Specifications

Projector Electrical Specifications

Projector Environmental Specifications

Projector Safety and Approvals Specifications

Supported Video Display Formats

General Projector Specifications

Type of display

Resolution

Lens

Color reproduction

Brightness

Poly-silicon TFT active matrix

1920 × 1080 pixels (1080p)

F=2.5 to 3.7

Focal length: 21.3 to 44.7 mm

Full color, up to 1 billion colors

PowerLite Pro Cinema LS9600e:

High Power Consumption mode:

White light output 1300 lumens (ISO 21118 standard)

Color light output 1300 lumens

Note: Color brightness (color light output) and white brightness

(white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.

143

Contrast ratio

PowerLite Pro Cinema LS10000:

High Power Consumption mode:

White light output 1500 lumens (ISO 21118 standard)

Color light output 1500 lumens

Note: Color brightness (color light output) and white brightness

(white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.

Infinite with the following settings: Color Mode, Dynamic; Power

Consumption, High; Zoom, Wide; and Lens Shift set with the image horizontally centered and vertically adjusted upwards by one half of the image height.

30 inches (0.76 m) to 300 inches (7.62 m) Image size

(in native aspect ratio)

Projection distance

(in native aspect ratio)

Projection methods

Optical aspect ratio

(width-to-height)

Focus adjustment

Zoom adjustment

Zoom ratio

(Tele-to-Wide)

Noise level

32.7 inches (0.83 m) to 716.1 inches (18.2 m)

Front, rear, ceiling-mounted

16:9

Powered

Powered

1 to 2.1

19 dB (with 4K Enhancement off on PowerLite Pro Cinema

LS10000)

± 30° vertical Keystone correction angle

Parent topic:

Technical Specifications

144

Projector Light Source Specifications

Type

Life

Laser Diode

PowerLite Pro Cinema LS9600e:

Output: 33.7 mW

Repetition rate: 0 to 100%

PowerLite Pro Cinema LS10000:

Output: 41.9 mW

Repetition rate: 0 to 100%

High Power Consumption mode:

Up to about 17000 hours

ECO Power Consumption mode:

Up to about 30000 hours

Parent topic:

Technical Specifications

Remote Control Specifications

Reception range

Batteries

32 feet (10 m)

Two alkaline or manganese AA

Parent topic:

Technical Specifications

Projector Dimension Specifications

Height (excluding feet)

Width

Depth

8.9 inches (225 mm)

21.7 inches (550 mm)

21.8 inches (553 mm)

145

Weight PowerLite Pro Cinema LS9600e:

37.5 lb (17 kg)

PowerLite Pro Cinema LS10000:

39.7 lb (18 kg)

Parent topic:

Technical Specifications

Projector Electrical Specifications

Rated frequency

Power supply

Power consumption

(100 to 120 V)

50/60 Hz

100 to 240 VAC ±10%

PowerLite Pro Cinema LS9600e:

3.5 to 1.6 A

PowerLite Pro Cinema LS10000:

4.6 to 2.1 A

Operating:

PowerLite Pro Cinema LS9600e:

High Power Consumption mode: 345 W

ECO Power Consumption mode: 218 W

PowerLite Pro Cinema LS10000:

High Power Consumption mode: 459 W

ECO Power Consumption mode: 267 W

Standby:

0.29 W (Communication Off), 2.8 W (Communication On)

146

Power consumption

(220 to 240 V)

Operating:

PowerLite Pro Cinema LS9600e:

Normal Power Consumption mode: 334 W

ECO Power Consumption mode: 215 W

PowerLite Pro Cinema LS10000:

Normal Power Consumption mode: 442 W

ECO Power Consumption mode: 262 W

Standby:

0.38 W (Communication Off), 3.3 W (Communication On)

Parent topic:

Technical Specifications

Projector Environmental Specifications

Temperature

Humidity (relative, noncondensing)

Operating altitude

Operating:

Up to 7500 ft (2286 m): 41 to 95 °F (5 to 35 °C)

7500 ft (2286 m) to 9843 ft (3000 m): 41 to 86 °F (5 to 30 °C)

Storage: 14 to 140 °F (–10 to 60 °C)

Operating: 20 to 80%

Storage: 10 to 90%

Up to 4921 feet (1500 m)

4921 feet (1500 m) to 9843 feet (3000 m) with High Altitude Mode enabled

Parent topic:

Technical Specifications

Projector Safety and Approvals Specifications

United States FCC Part 15 Class B (DoC)

UL60950-1 2nd edition (cTUVus Mark)

147

Canada ICES-003 Class B

CSA C22.2 No. 60950-1-07 (cTUVus Mark)

Parent topic:

Technical Specifications

Supported Video Display Formats

For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.

Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the projector. (See your computer or video card manual for details.)

The table here lists the compatible refresh rate and resolution for each compatible video display format.

Display format

Computer signals (analog RGB)

Refresh rate (in Hz)

VGA

SVGA

60/72/75/85

56/60/72/75/85

XGA

SXGA

60/70/75/85

70/75/85

60/75/85

60/75/85

WXGA 60

60

60/75/85

60 WXGA++

Composite video

TV (NTSC)

TV (PAL)

TV (SECAM)

Component video

60

50/60

50

Resolution (in pixels)

640 × 480

800 × 600

1024 × 768

1152 × 864

1280 × 960

1280 × 1024

1280 × 768

1366 × 768

1280 × 800

1600 × 900

720 × 480

720 × 576

720 × 576

148

Display format

SDTV (480i)

SDTV (576i)

SDTV (480p)

SDTV (576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

Refresh rate (in Hz)

60

50

60

50

50/60

50/60

50/60

HDMI input signals

VGA

SDTV (480i/480p)

SDTV (576i/576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

60

60

50

50/60

50/60

24/30/50/60

4K × 2K (PowerLite Pro Cinema 24/25/30/50/60

LS10000)

50/60

4K × 2K (SMPTE; PowerLite Pro 24

Cinema LS10000)

MHL input signals

SDTV (480i/480p)

SDTV (576i/576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

60

50

50/60

50/60

24/30

WirelessHD input signals

VGA 60

149

Resolution (in pixels)

720 × 480

720 × 576

720 × 480

720 × 576

1280 × 720

1920 × 1080

1920 × 1080

640 × 480

720 × 480

720 × 576

1280 × 720

1920 × 1080

1920 × 1080

3840 × 2160

4096 × 2160

4096 × 2160

720 × 480

720 × 576

1280 × 720

1920 × 1080

1920 × 1080

640 × 480

Display format

SDTV (480i/480p)

SDTV (576i/576p)

HDTV (720p)*

Refresh rate (in Hz)

60

50

50/60

Resolution (in pixels)

720 × 480

720 × 576

1280 × 720

HDTV (1080i)

HDTV (1080p)*

50/60

24/30

1920 × 1080

1920 × 1080

MHL input signals via WirelessHD Transmitter (HDMI5 port only)

SDTV (480i/480p) 60 720 × 480

SDTV (576i/576p)

HDTV (720p)*

HDTV (1080i)

HDTV (1080p)*

50

50/60

50/60

24/50/60

720 × 576

1280 × 720

1920 × 1080

1920 × 1080

* With WirelessHD, these signals do not support Deep Color:

• 2D: 1080p 50/60 Hz

• 3D: 1080p 24 Hz frame packing, 720p 50/60 Hz frame packing, and 1080p 50/60 Hz side by side

3D Input Signals

Display format

HDTV (720p)

Refresh rate (in Hz)

50/60

HDTV (1080i)

HDTV (1080p)

50/60

50/60

24

Resolution (in pixels) 3D formats

1280 × 720 Frame Packing

Side by Side

Top and Bottom

1920 × 1080

1920 × 1080

1920 × 1080

Side by Side

Side by Side

Frame Packing

Side by Side

Top and Bottom

3D Input Signals via WirelessHD Transmitter (HDMI5 port only)

150

Display format

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

Refresh rate (in Hz)

50/60

50/60

50/60

24

Resolution (in pixels) 3D formats

1280 × 720 Side by Side

Top and Bottom

1920 × 1080

1920 × 1080

1920 × 1080

Side by Side

Side by Side

Top and Bottom

Parent topic:

Technical Specifications

151

Notices

Check these sections for important notices about your projector.

Recycling

Important Safety Information

Laser Safety Information

Important Safety Instructions

FCC Compliance Statement

Trademarks

Open Source Software License

Copyright Notice

Recycling

Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.

Parent topic:

Notices

Important Safety Information

Caution: Never look into the projector lens when the laser is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User's Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

Warning: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Parent topic:

Notices

152

Laser Safety Information

This projector is a Class 2 laser product that complies with the IEC60825-1 international standard for lasers. Follow these safety instructions when using the projector.

• If an error occurs in the projector, turn off the power and unplug the projector immediately. Continuing to use the projector could result in an electric shock, fire, or visual impairment. Contact Epson support.

• Do not attempt to dissassemble or modify the projector. The projector contains a high-power laser component. Serious injury could result.

• Do not look into the lens during projection. Also, do not look into the lens using optical devices, such as a magnifying glass or telescope. This could cause visual impairment.

• When turning on the projector at a distance using the remote control, make sure no one is looking into the lens.

• Do not allow small children to operate the projector. Children must be accompanied by an adult.

• Do not apply optical devices, such as a magnifying glass or reflector, to the projected image. Using the projector may result in physical harm, fire, or an accident.

• Before using the projector, make sure there is nothing in the area that could reflect the projected image.

• When disposing of the projector, do not disassemble it. Dispose of the projector in accordance with your local or national laws and regulations.

There is a label attached to the projector to indicate it is a Class 2 product. The label contains the following information:

• Invisible laser radiation

• Do not stare into beam or view directly with optical instruments

• Class 2 laser product

• Pulse width

Laser Optical Path

Parent topic:

Notices

153

Laser Optical Path

When using the Lens Shift function, the laser light from the projection lens is diffused within the following range:

When Lens Shift is at the maximum vertical position: 32° from the center of the lens

When Lens Shift is at the maximum horizontal position: 34° from the center of the lens

Parent topic:

Laser Safety Information

Important Safety Instructions

Follow these safety instructions when setting up and using the projector:

• Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes.

• Do not place the projector on an unstable cart, stand, or table.

• Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 3° forward or back.

154

• If the projector is mounted on a ceiling or wall, it should be installed by qualified technicians using mounting hardware designed for use with this projector.

• When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants. This may cause the projector case to crack and the projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and could damage the projector.

• Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of magnetic fields.

• Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company.

• Place the projector near a wall outlet where the plug can be easily unplugged.

• Take the following precautions when handling the plug: Do not hold the plug with wet hands. Do not insert the plug into a dusty outlet. Insert the plug firmly into the outlet. Do not pull the power cord when disconnecting the plug; always be sure to hold the plug when disconnecting it. Do not overload wall outlets, extension cords, or power strips. Failure to comply with these precautions could result in fire or electric shock.

• Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug.

• Unplug the projector from the wall outlet before cleaning. Use a dry cloth (or, for stubborn dirt or stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol cleaners, any sprays containing flammable gas, or solvents such as alcohol, paint thinner, or benzine.

• Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it on top of loose papers. Do not cover the projector with a blanket, curtain, or tablecloth. If you are setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and the air exhaust vent.

• Do not operate the projector in a closed-in cabinet unless proper ventilation is provided.

• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector.

• If you are using two or more projectors side-by-side, leave at least 20 inches (50 cm) of space between the projectors to allow for proper ventilation.

• You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. Do not use canned air, or the gases may leave a residue.

• Do not store the projector outdoors for an extended length of time.

155

• Except as specifically explained in this manual, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.

• Never open any covers on the projector except as specifically explained in this manual. Never attempt to disassemble or modify the projector. Refer all repairs to qualified service personnel.

• Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: if it does not operate normally when you follow the operating instructions, or exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been damaged.

• Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.

• Unplug the projector when it will not be used for extended periods.

• Do not use the projector where it may be exposed to rain, water, or excessive humidity.

• Do not use or store the projector where it may be exposed to smoke, steam, corrosive gases, excessive dust, vibration, or shock.

• Do not use the projector where flammable or explosive gases may be present.

• Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle.

• If you use the projector in a country other than where you purchased it, use the correct power cord for that country.

• Do not stand on the projector or place heavy objects on it.

• Do not use the projector outside of the required temperature range of 41 to 95 °F (5 to 35 °C) at an altitude of 7500 feet (2286 m) or less, or 41 to 86 °F (5 to 30 °C) at a higher altitude. Doing so may cause an unstable display and could lead to projector damage. Do not use or store the projector where it may be exposed to sudden changes in temperature.

• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case.

• Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.

• Before you move the projector, make sure its power is turned off, the plug is disconnected from the outlet, and all cables are disconnected.

• Do not place the source of an open flame, such as a lit candle, on or near the projector.

156

• Do not block the lens during projection using a book or any other object. This could damage the projector or cause a fire.

• Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or pull it excessively. Keep the power cord away from hot electrical appliances.

WARNING: The cords included with this product contain chemicals, including lead, known to the State of

California to cause birth defects or other reproductive harm. Wash hands after handling. (This notice is provided in accordance with Proposition 65 in Cal. Health & Safety Code § 25249.5 and following.)

Restriction of Use

Parent topic:

Notices

Restriction of Use

When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.

Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care, please make your own judgment on this product's suitability after a full evaluation.

Parent topic:

Important Safety Instructions

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

157

• Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC

Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

For Canadian Users

CAN ICES-3(B)/NMB-3(B)

Wireless Telegraphy Act Regulations

Parent topic:

Notices

Wireless Telegraphy Act Regulations

The following acts are prohibited by the Wireless Telegraphy Act:

• Modifying and disassembling (including the antenna)

• Removing the label of conformance

Parent topic:

FCC Compliance Statement

Trademarks

EPSON ® , PowerLite ® , and Quick Corner ® are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.

Accolade ® and PrivateLine ® are registered trademarks; and Epson Store marks of Epson America, Inc.

SM and Extra Care SM are service

Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.

HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI

Licensing LLC.

158

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

Parent topic:

Notices

Open Source Software License

GNU GPL

This projector product includes the open source software programs which apply the GNU General Public

License Version 2 or later version ("GPL Programs").

We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product.

If you desire to receive the source code of the GPL Programs, contact Epson as described in the User's

Guide.

These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public

License for more details.

The list of GPL Programs is as follows and the names of author are described in the source code of the

GPL Programs

The list of GPL Programs busybox-1.13.4

iptables-1.4.4

libgcc1(gcc-4.3.3) libstdc++-6.0.10

linux-2.6.27

patches udhcp 0.9.8

uvc rev.219

wireless_tools 29

159

EPSON original drivers

The GNU General Public License Version 2 is as follows. You also can see the GNU General Public

License Version 2 at http://www.gnu.org/licenses/.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright (c) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA

02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public

License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.

160

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the

Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

161

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

162

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program

(or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason

(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all.

For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this

License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted

163

only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public

License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this

License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the

Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free

Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.

Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR

THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES

PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,

YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL

ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE

OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR

DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES

OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

164

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the

"copyright" line and a pointer to where the full notice is found.

<one line to give the program's name and a brief idea of what it does.>

Copyright (c) <year> <name of author>

This program is free software; you can redistribute it and/or modify it under the terms of the GNU

General Public License as published by the Free Software Foundation; either version 2 of the License, or

(at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301

USA.

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (c) year name of author Gnomovision comes with ABSOLUTELY NO

WARRANTY; for details type 'show w'. This is free software, and you are welcome to redistribute it under certain conditions; type 'show c' for details.

The hypothetical commands 'show w' and 'show c' should show the appropriate parts of the General

Public License. Of course, the commands you use may be called something other than 'show w' and

'show c'; they could even be mouse-clicks or menu items--whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a

"copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program 'Gnomovision' (which makes passes at compilers) written by James Hacker.

<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.

GNU LGPL

165

This projector product includes the open source software programs which apply the GNU Lesser

General Public License Version 2 or later version ("LGPL Programs").

We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product.

If you desire to receive the source code of the LGPL Programs, please see the "EPSON Projector

Contact List" in the User's Guide, and contact the customer support of your region.

These LGPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public

License for more details.

The list of LGPL Programs is as follows and the names of author are described in the source code of the

LGPL Programs.

LGPL Programs glibc-2.8

SDL-1.2.13

SDL-Image

The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser

General Public License Version 2 at http://www.gnu.org/licenses/.

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

Copyright ©) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA

02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library

Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.

You can use it too, but we suggest you first think carefully about whether this license or the ordinary

General Public License is the better strategy to use in any particular case, based on the explanations below.

166

When we speak of free software, we are referring to freedom of use, not price. Our General Public

Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library.

Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License.

This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General

Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The

Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

167

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in nonfree programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,

DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".

A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".)

"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

168

1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that

169

they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General

Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of

Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the

Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms

170

of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the

Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable

"work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that

(1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library,

171

provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the

Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this

License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason

(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on

172

consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this

License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General

Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this

License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the

Library does not specify a license version number, you may choose any version ever published by the

Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR

THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE

LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE,

YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL

ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE

OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA

BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A

173

FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General

Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.

<one line to give the library's name and a brief idea of what it does.>

Copyright (c) <year> <name of author>

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser

General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301

USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a

"copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library 'Frob' (a library for tweaking knobs) written by James Random Hacker.

<signature of Ty Coon>, 1 April 1990

Ty Coon, President of Vice

That's all there is to it!

BSD License (Berkeley Software Distribution License)

174

This projector product includes the open source software program "University of California, Berkeley

License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License".

The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of BSD License programs busybox-1.13.4

License terms of conditions of each program which are provided by owner of the copyright to the "BSD

License" are as follows.

Copyright (c) The Regents of the University of California. All rights reserved.

This code is derived from software contributed to Berkeley by Kenneth Almquist.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

libjpeg

This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg".

The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

175

List of libjpeg programs libjpeg-6b

License terms of conditions of each program which are provided by owner of the copyright to the

"libjpeg" are as follows.

Copyright (c) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software.

For conditions of distribution and use, see the accompanying README file.

This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.

You are welcome to redistribute this software and to use it for any purpose, subject to the conditions under LEGAL ISSUES, below.

LEGAL ISSUES

============

In plain English:

1. We don't promise that this software works. (But if you find any bugs, please let us know!)

2. You can use this software for whatever you want. You don't have to pay us.

3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code.

In legalese:

The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.

This software is copyright (c) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.

Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions:

(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.

(2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent JPEG Group".

(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind.

176

These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.

Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as

"the Independent JPEG Group's software".

We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor.

ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.)

However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does not limit you more than the foregoing paragraphs do.

The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free

Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable.

It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM,

AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software.

(Since arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.) So far as we are aware, there are no patent restrictions on the remaining code.

The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the

Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but are readable by all standard GIF decoders.

We are required to state that

"The Graphics Interchange Format(c)) is the Copyright property of CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated." libpng

This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng".

The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

177

List of libpng programs libpng-1.2.49

License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows.

This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.

COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:

If you modify libpng you may insert additional notices immediately following this sentence.

This code is released under the libpng license.

libpng version 1.2.6, August 15, 2004, through 1.2.49, March 29, 2012, are Copyright (c) 2004, 2006-

2009 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors

Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn

Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors

Simon-Pierre Cadieux

Eric S. Raymond

Gilles Vollant and with the following additions to the disclaimer:

There is no warranty against interference with your enjoyment of the library or against infringement.

There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user.

libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright ©) 1998, 1999 Glenn

Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors:

Tom Lane

Glenn Randers-Pehrson

Willem van Schaik

178

libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger

Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors:

John Bowler

Kevin Bracey

Sam Bushell

Magnus Holmgren

Greg Roelofs

Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric

Schalnat, Group 42, Inc.

For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals:

Andreas Dilger

Dave Martindale

Guy Eric Schalnat

Paul Schmidt

Tim Wegner

The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the

PNG Reference Library, even if advised of the possibility of such damage.

Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions:

1. The origin of this source code must not be misrepresented.

2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.

3. This Copyright notice may not be removed or altered from any source or altered source distribution.

The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.

179

A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL));

Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg"

(88x31) and "pngnow.png" (98x31).

Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the

Open Source Initiative.

Glenn Randers-Pehrson [email protected]

March 29, 2012 zlib

This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib".

The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

List of zlib programs zlib-1.1.4

License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows.

Copyright notice:

(c) 1995-1998 Jean-loup Gailly and Mark Adler

This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

3. This notice may not be removed or altered from any source distribution.

Jean-loup Gailly

180

[email protected] Mark Adler [email protected]

If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.

If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.

mDNSResponder

This projector product includes the open source software program "mDNSResponder" which applies the following license terms "Apache License Version 2.0, January 2004".

List of "mDNSResponder" mDNSResponder-107.6 (only mDNSResponderPosix is used)

License terms "Apache License Version 2.0, January 2004" are as follows.

Apache License

Version 2.0, January 2004 http://www.apache.org/licenses/

TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION

1. Definitions.

"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by

Sections 1 through 9 of this document.

"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the

License.

"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (I) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.

"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.

"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.

181

"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.

"Work" shall mean the work of authorship, whether in Source or Object form, made available under the

License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).

"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.

"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to

Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution."

"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.

2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.

3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity

(including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.

182

4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions:

(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and

(b) You must cause any modified files to carry prominent notices stating that You changed the files; and

(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and

(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the

Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the

License.

You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such

Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.

5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this

License, without any additional terms or conditions.

Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions.

6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.

7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT

WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR

A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this

License.

183

8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.

9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof,

You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations,

You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other

Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.

END OF TERMS AND CONDITIONS

APPENDIX: How to apply the Apache License to your work.

To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!)

The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.

Copyright [yyyy] [name of copyright owner]

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License.

You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

See the License for the specific language governing permissions and limitations under the License.

newlib

This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib".

184

The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of newlib programs newlib 1.17.0

License terms of conditions of each program which are provided by owner of the copyright to the "newlib" are as follows.

The newlib subdirectory is a collection of software from several sources.

Each file may have its own copyright/license that is embedded in the source file. Unless otherwise noted in the body of the source file(s), the following copyright notices will apply to the contents of the newlib subdirectory:

(1) Red Hat Incorporated

Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved.

This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express permission of Red Hat, Inc.

(2) University of California, Berkeley

Copyright (c) 1981-2000 The Regents of the University of California.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

* Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

185

DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(3) David M. Gay (AT&T 1991, Lucent 1998)

The author of this software is David M. Gay.

Copyright ©) 1991 by AT&T.

Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.

THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED

WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY

REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF

THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.

-----------

The author of this software is David M. Gay.

Copyright (c) 1998-2001 by Lucent Technologies

All Rights Reserved

Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that the copyright notice and this permission notice and warranty disclaimer appear in supporting documentation, and that the name of Lucent or any of its entities not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.

LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR

ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES

OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,

WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,

ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

(4) Advanced Micro Devices

Copyright 1989, 1990 Advanced Micro Devices, Inc.

186

This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD.

AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS

SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR

USE OF THIS SOFTWARE.

So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 0800-

89-1131 in the UK, or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.

Advanced Micro Devices, Inc.

29K Support Products

Mail Stop 573

5900 E. Ben White Blvd.

Austin, TX 78741

800-292-9263

(5) C.W. Sandmann

Copyright (C) 1993 C.W. Sandmann

This file may be freely distributed as long as the author's name remains.

(6) Eric Backus

(C) Copyright 1992 Eric Backus

This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software.

(7) Sun Microsystems

Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.

Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.

(8) Hewlett Packard

(c) Copyright 1986 HEWLETT-PACKARD COMPANY

To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of

187

Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company makes no representations about the suitability of this software for any purpose.

(9) Hans-Peter Nilsson

Copyright (C) 2001 Hans-Peter Nilsson

Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.

THIS SOFTWARE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

(11) Christopher G. Demetriou

Copyright (c) 2001 Christopher G. Demetriou

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(12) SuperH, Inc.

Copyright 2002 SuperH, Inc. All rights reserved

188

This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH.

SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS

SOFTWARE. IN NO EVENT SHALL SUPERH BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING,

PERFORMANCE, OR USE OF THIS SOFTWARE.

So that all may benefit from your experience, please report any problems or suggestions about this software to the SuperH Support Center via e-mail at [email protected].

SuperH, Inc.

405 River Oaks Parkway

San Jose

CA 95134

USA

(13) Royal Institute of Technology

Copyright (c) 1999 Kungliga Tekniska Hökolan (Royal Institute of Technology, Stockholm, Sweden).

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS "AS IS" AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

189

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(14) Alexey Zelkin

Copyright (c) 2000, 2001 Alexey Zelkin <[email protected]>

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(15) Andrey A. Chernov

Copyright (C) 1997 by Andrey A. Chernov, Moscow, Russia.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

190

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(16) FreeBSD

Copyright (c) 1997-2002 FreeBSD Project.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(17) S. L. Moshier

Author: S. L. Moshier.

Copyright (c) 1984, 2000 S.L. Moshier

Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.

THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED

WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NO REPRESENTATION OR WARRANTY OF

ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR

ANY PARTICULAR PURPOSE.

191

(18) Citrus Project

Copyright (c)1999 Citrus Project,

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(19) Todd C. Miller

Copyright (c) 1998 Todd C. Miller <[email protected]>

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR

BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

192

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING

IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

(20) DJ Delorie (i386)

Copyright (C) 1991 DJ Delorie

All rights reserved.

Redistribution and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms.

This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

(23) Intel (i960)

Copyright (c) 1993 Intel Corporation

Intel hereby grants you permission to copy, modify, and distribute this software and its documentation.

Intel grants this permission provided that the above copyright notice appears in all copies and that both the copyright notice and this permission notice appear in supporting documentation. In addition, Intel grants this permission provided that you prominently mark as "not part of the original" any modifications made to this software or documentation, and that the name of Intel Corporation not be used in advertising or publicity pertaining to distribution of the software or the documentation without specific, written prior permission.

Intel Corporation provides this AS IS, WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED,

INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. Intel makes no guarantee or representations regarding the use of, or the results of the use of, the software and documentation in terms of correctness, accuracy, reliability, currentness, or otherwise; and you rely on the software, documentation and results solely at your own risk.

IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF

PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN

NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE

PRODUCT LICENSED HEREUNDER.

(26) Mike Barcroft

Copyright (c) 2001 Mike Barcroft <[email protected]>

All rights reserved.

193

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(27) Konstantin Chuguev (--enable-newlib-iconv)

Copyright (c) 1999, 2000

Konstantin Chuguev. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

iconv (Charset Conversion Library) v2.0

194

(28) Artem Bityuckiy (--enable-newlib-iconv)

Copyright (c) 2003, Artem B. Bityuckiy, SoftMine Corporation. Rights transferred to Franklin Electronic

Publishers.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(30) - Alex Tatmanjants (targets using libc/posix)

Copyright (c) 1995 Alex Tatmanjants <[email protected]> at Electronni Visti IA, Kiev, Ukraine.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

195

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(31) - M. Warner Losh (targets using libc/posix)

Copyright (c) 1998, M. Warner Losh <[email protected]>

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(32) - Andrey A. Chernov (targets using libc/posix)

Copyright (C) 1996 by Andrey A. Chernov, Moscow, Russia.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

196

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(33) - Daniel Eischen (targets using libc/posix)

Copyright (c) 2001 Daniel Eischen <[email protected]>.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(35) - ARM Ltd (arm and thumb variant targets only)

Copyright (c) 2009 ARM Ltd

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

197

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of the company may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY ARM LTD "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL ARM LTD BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(36) - CodeSourcery, Inc.

Copyright (c) 2009 CodeSourcery, Inc.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

* Neither the name of CodeSourcery nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY CODESOURCERY, INC. "AS IS" AND ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL CODESOURCERY BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(37) MIPS Technologies, Inc

198

/*

* Copyright (c) 2009 MIPS Technologies, Inc.

*

* All rights reserved.

*

* Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

*

* * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

* * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

* * Neither the name of MIPS Technologies Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

/*

MIT License

This projector product includes the open source software program which applies the terms and conditions provided by owner of the copyright to the "MIT License".

The "MIT License" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of MIT License programs jquery-1.7.2.min.js

jquery-ui-1.8.20.custom.zip

199

jquery.ui.touch-punch.js

License terms of conditions of each program which are provided by owner of the copyright to the "MIT

License" are as follows.

Copyright (c) 2012 jQuery Foundation and other contributors, http://jquery.com/

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS

OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN

CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

TOPPERS/JSP

This projector product includes the open source software program "TOPPERS/JSP" which applies the terms and conditions provided by owner of the copyright to the "TOPPERS/JSP". The "TOPPERS/JSP" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

List of TOPPERS/JSP programs jsp-1.4.3

toppers-pro

License terms of conditions of each program which are provided by owner of the copyright to the

"TOPPERS/JSP" are as follows.

TOPPERS/JSP Kernel

Toyohashi Open Platform for Embedded Real-Time Systems/

Just Standard Profile Kernel

Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of

Technology, JAPAN

Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory

200

Graduate School of Information Science, Nagoya Univ., JAPAN.

The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the conditions described in Version 2 of the GNU Public License officially announced by the Free Software

Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization) of this software (this software includes alterations, likewise below) without compensation.

(1) When this software is utilized in the form of source code, the above copyright declaration, these conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged form inside the source code.

(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).

(3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc., one of the following conditions shall be satisfied.

(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).

(b) The TOPPERS Project shall be notified owing to a method in which the form of distribution is decided otherwise.

(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software.

This software is something that is provided with no guarantee. The above copyright holder and the

TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear responsibility for whatever damages occur either directly or indirectly through the utilization of this software.

Note: The TOPPERS License has been revised several times; what is shown above is the latest version that is to be applied to software made public hereafter.

TINET

This projector product includes the open source software program "TINET" which applies the terms and conditions provided by owner of the copyright to the "TINET". The "TINET" are WITHOUT ANY

WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE.

List of TINET programs tinet-1.4.4

201

License terms of conditions of each program which are provided by owner of the copyright to the

"TINET" are as follows.

(1) FreeBSD

Copyright (c) 1980, 1986, 1993

The Regents of the University of California. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

This product includes software developed by the University of California, Berkeley and its contributors.

4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(6) TINET and TOPPERS

TINET (TCP/IP Protocol Stack)

Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of

Technology, JAPAN

The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the conditions described in Version 2 of the GNU Public License officially announced by the Free Software

Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization) of this software (this software includes alterations, likewise below) without compensation.

202

(1) When this software is utilized in the form of source code, the above copyright declaration, these conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged form inside the source code.

(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).

(3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc., following conditions shall be satisfied.

(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).

(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software.

This software is something that is provided with no guarantee. The above copyright holder and the

TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear responsibility for whatever damages occur either directly or indirectly through the utilization of this software.

Bluetopia ® is provided for your use by Stonestreet One, LLC ®

Stonestreet One, LLC ® under a software license agreement.

is and shall remain the sole owner of all right, title and interest whatsoever in and to Bluetopia ®

LLC ® and your use is subject to such ownership and to the license agreement. Stonestreet One, reserves all rights related to Bluetopia ® not expressly granted under the license agreement and no other rights or licenses are granted either directly or by implication, estoppel or otherwise, or under any patents, copyrights, mask works, trade secrets or other intellectual property rights of Stonestreet One,

LLC ® .

© 2000-2012 Stonestreet One, LLC ® All Rights Reserved.

Parent topic:

Notices

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of:

203

accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson

Approved Products by Seiko Epson Corporation.

This information is subject to change without notice.

A Note Concerning Responsible Use of Copyrighted Materials

Copyright Attribution

Parent topic:

Notices

A Note Concerning Responsible Use of Copyrighted Materials

Epson encourages each user to be responsible and respectful of the copyright laws when using any

Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law.

Parent topic:

Copyright Notice

Copyright Attribution

© 2015 Epson America, Inc.

1/15

CPD-40296R1

Parent topic:

Copyright Notice

204

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents