HP ProLiant Generation ML310 User guide

HP ProLiant ML310 Generation 5 Server
User Guide
Part Number 450225-002
November 2007 (Second Edition)
© Copyright 2007 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Windows Server 2003 is a trademark of Microsoft Corporation.
Audience assumptions
This guide is for an experienced service technician. HP assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with hazardous energy levels and
are familiar with weight and stability precautions for rack installations.
Contents
Component identification ............................................................................................................... 6
Front panel components ............................................................................................................................. 6
Front panel LEDs and buttons ...................................................................................................................... 7
SAS and SATA device numbers................................................................................................................... 8
Hot-plug SATA or SAS hard drive LEDs ........................................................................................................ 8
Rear panel components.............................................................................................................................. 9
Rear panel LEDs ...................................................................................................................................... 10
System board components........................................................................................................................ 11
System maintenance switch............................................................................................................. 12
NMI functionality........................................................................................................................... 13
System board LEDs .................................................................................................................................. 13
System LEDs and internal health LED combinations....................................................................................... 14
PCI-X extender board components ............................................................................................................. 15
Fan locations .......................................................................................................................................... 16
Operations................................................................................................................................. 17
Power up the server ................................................................................................................................. 17
Power down the server............................................................................................................................. 17
Unlock the bezel ..................................................................................................................................... 18
Remove the bezel .................................................................................................................................... 18
Remove the access panel.......................................................................................................................... 19
Install the access panel............................................................................................................................. 19
Remove a media bay blank ...................................................................................................................... 20
Remove a bezel blank.............................................................................................................................. 20
Remove the system air baffle and PCI card guide ........................................................................................ 21
Setup......................................................................................................................................... 22
Optional installation services .................................................................................................................... 22
Rack planning resources........................................................................................................................... 22
Optimum environment.............................................................................................................................. 23
Space and airflow requirements ...................................................................................................... 23
Temperature requirements............................................................................................................... 23
Power requirements ....................................................................................................................... 24
Electrical grounding requirements .................................................................................................... 24
Warnings and cautions............................................................................................................................ 25
Identifying server shipping carton contents.................................................................................................. 26
Installing hardware options....................................................................................................................... 26
Setting up a server .................................................................................................................................. 26
Installing the operating system................................................................................................................... 27
Registering the server............................................................................................................................... 28
Hardware options installation....................................................................................................... 29
Introduction ............................................................................................................................................ 29
Memory ................................................................................................................................................. 29
DIMM installation guidelines ........................................................................................................... 29
Installing DIMMs ........................................................................................................................... 30
Hard drives ............................................................................................................................................ 30
Contents
3
SATA optical drive .................................................................................................................................. 32
USB tape drive........................................................................................................................................ 33
Full-height tape drive................................................................................................................................ 35
Diskette drives......................................................................................................................................... 37
Installing a legacy diskette drive ...................................................................................................... 37
Installing a USB diskette drive ......................................................................................................... 39
Expansion boards ................................................................................................................................... 39
Removing the expansion slot cover .................................................................................................. 39
Installing expansion boards ............................................................................................................ 40
PCI-X extender board ............................................................................................................................... 41
SAS controller......................................................................................................................................... 42
Parallel and second serial connector .......................................................................................................... 42
Cabling ..................................................................................................................................... 44
Server cabling ........................................................................................................................................ 44
SATA hard drive cabling .......................................................................................................................... 45
SAS hard drive cabling ............................................................................................................................ 45
Software and configuration utilities ............................................................................................... 46
Configuration tools .................................................................................................................................. 46
SmartStart software........................................................................................................................ 46
HP ROM-Based Setup Utility............................................................................................................ 47
Array Configuration Utility .............................................................................................................. 48
Embedded SATA RAID ................................................................................................................... 49
Option ROM Configuration for Arrays ............................................................................................. 51
HP ProLiant Essentials Rapid Deployment Pack .................................................................................. 51
Re-entering the server serial number and product ID ........................................................................... 52
Management tools................................................................................................................................... 52
Automatic Server Recovery ............................................................................................................. 52
ROMPaq utility.............................................................................................................................. 52
Integrated Lights-Out 2 technology ................................................................................................... 53
Erase Utility .................................................................................................................................. 53
Management Agents...................................................................................................................... 53
HP Systems Insight Manager ........................................................................................................... 53
USB support.................................................................................................................................. 54
Diagnostic tools ...................................................................................................................................... 55
HP Insight Diagnostics .................................................................................................................... 55
HP Insight Diagnostics survey functionality ........................................................................................ 55
Integrated Management Log ........................................................................................................... 56
ROMPaq disaster recovery ............................................................................................................. 56
Keeping the system current ....................................................................................................................... 57
Drivers ......................................................................................................................................... 57
ProLiant Support Packs ................................................................................................................... 57
Operating system version support .................................................................................................... 57
HP Smart Update Manager............................................................................................................. 57
Change control and proactive notification ........................................................................................ 58
Care Pack .................................................................................................................................... 58
Battery replacement .................................................................................................................... 59
Troubleshooting .......................................................................................................................... 60
Troubleshooting resources ........................................................................................................................ 60
Pre-diagnostic steps ................................................................................................................................. 60
Important safety information............................................................................................................ 60
Symptom information ..................................................................................................................... 62
Contents
4
Prepare the server for diagnosis ...................................................................................................... 63
Loose connections ................................................................................................................................... 63
Service notifications................................................................................................................................. 64
Troubleshooting flowcharts ....................................................................................................................... 64
Start diagnosis flowchart ................................................................................................................ 64
General diagnosis flowchart ........................................................................................................... 65
Server power-on problems flowchart ................................................................................................ 67
POST problems flowchart ............................................................................................................... 70
OS boot problems flowchart ........................................................................................................... 71
Server fault indications flowchart ..................................................................................................... 73
POST error messages and beep codes ....................................................................................................... 75
Regulatory compliance notices ..................................................................................................... 76
Regulatory compliance identification numbers ............................................................................................. 76
Federal Communications Commission notice............................................................................................... 76
FCC rating label............................................................................................................................ 76
Class A equipment......................................................................................................................... 76
Class B equipment ......................................................................................................................... 76
Declaration of conformity for products marked with the FCC logo, United States only....................................... 77
Modifications.......................................................................................................................................... 77
Cables ................................................................................................................................................... 77
Canadian notice (Avis Canadien).............................................................................................................. 78
European Union regulatory notice ............................................................................................................. 78
Disposal of waste equipment by users in private households in the European Union ......................................... 78
Japanese notice ...................................................................................................................................... 79
BSMI notice ............................................................................................................................................ 79
Korean notice ......................................................................................................................................... 80
Laser compliance .................................................................................................................................... 80
Battery replacement notice........................................................................................................................ 80
Taiwan battery recycling notice................................................................................................................. 81
Power cord statement for Japan................................................................................................................. 81
Acoustics statement for Germany (Geräuschemission) .................................................................................. 81
Electrostatic discharge ................................................................................................................. 82
Preventing electrostatic discharge .............................................................................................................. 82
Grounding methods to prevent electrostatic discharge .................................................................................. 82
Specifications ............................................................................................................................. 83
Environmental specifications ..................................................................................................................... 83
Server specifications ................................................................................................................................ 83
Technical support........................................................................................................................ 85
Before you contact HP.............................................................................................................................. 85
HP contact information ............................................................................................................................. 85
Customer Self Repair ............................................................................................................................... 85
Acronyms and abbreviations........................................................................................................ 93
Index......................................................................................................................................... 96
Contents
5
Component identification
Front panel components
Item
Description
1
DVD-ROM drive
2
Media bays (bezel blanks)
3
USB connectors (2)
4
Bezel lock
5
Hard drive bays
Component identification 6
Front panel LEDs and buttons
Item
Description
Status
1
DVD-ROM drive ejector button
—
2
DVD-ROM drive activity LED
On = Activity
Off = No activity
3
Power On/Standby button
—
4
System power LED
Green = AC power is functioning
Amber = AC power is in standby mode
Off = AC power is not available
5
Hard drive activity LED
Green = Activity
Off = No activity
6
NIC link/activity LED
Green = Linked
Flashing green = Linked with activity on the network
Off = No network link
7
Internal health LED*
Green = System health is OK
Amber = System health is degraded
Red = System health is critical
Off = Normal (when in standby mode)
* For servers with redundant hot-plug power supplies, the internal health LED also signals a power supply event
("Rear panel LEDs" on page 10).
Component identification 7
SAS and SATA device numbers
Hot-plug SATA or SAS hard drive LEDs
Item
LED description
Status
1
Fault/UID status
Amber = Drive failure
Flashing amber = Fault-process activity
Blue = Unit identification is active
Off = No fault-process activity
2
Online/Activity status
Green = Drive activity
Flashing green = High activity on the
drive or drive is being configured as part
of an array
Off = No drive activity
Component identification 8
The online/activity status LED will not illuminate if using SATA drives connected to the embedded storage
device. In this configuration, SATA hard drive activity can be identified using the hard drive activity LED
on the system front panel.
Rear panel components
The server may look different from that shown.
Item
Description
1
Power supply connector
2
Mouse connector
3
Keyboard connector
4
10/100/1000 NIC 1 connector
5
iLO 2 management port
6
USB connectors (2)
7
Video connector
8
Serial connector
Component identification 9
Rear panel LEDs
•
Redundant hot-plug power supply model
Item
LED
Status
1
NIC/iLO 2 link
On = Link
Off = No link
2
NIC/iLO 2 activity
Flashing = Activity
Off = No activity
3
Redundant power
supply
Green = Power supply is on and
functioning
Off = Power supply is not connected
or power supply fault
•
Non-redundant non-hot-plug power supply model
Component identification 10
Item
LED
Status
1
NIC/iLO 2 link
On = Link
Off = No link
2
NIC/iLO 2 activity
Flashing = Activity
Off = No activity
System board components
For this server, some system board slots and connectors are reserved.
Item
Description
1
DIMM slot 1 (bank A)
2
DIMM slot 2 (bank B)
3
DIMM slot 3 (bank A)
4
DIMM slot 4 (bank B)
5
Processor socket
6
Redundant power supply connector
7
System power connector
8
Processor power connector
9
Processor heatsink fan connector
10
Reserved
11
Reserved
12
Front USB cable connector
13
SATA connector 2 (hard drive)
14
Front panel LED cable connector
15
NMI jumper
16
Temperature sensor connector
Component identification 11
Item
Description
17
System maintenance switch
18
PCI fan connector
19
System battery
20
SATA connector 4 (hard drive)
21
SATA connector 6 (optical drive)
22
Internal USB connector
23
PCI-X extender board connector
24
SATA connector 5 (optical drive)
25
USB tape drive connector
26
Diskette drive connector
27
SATA connector 3 (hard drive)
28
SATA connector 1 (hard drive)
29
Parallel connector
30
Serial connector
31
PCI Express expansion slot 3
32
Reserved
33
PCI Express expansion slot 5*
34
PCI Express expansion slot 6*
35
Rear fan connector
36
PCI Express expansion slot 7*
37
Reserved
* x8 PCI Express cards are supported, but will run at x1 speeds.
System maintenance switch
Position
Default
Function
S1
Off
Off = iLO 2 security is enabled
On = iLO 2 security is disabled
S2
Off
Off = Normal operation
On = RBSU will not commit any
configuration changes *
S3
Off
Reserved
S4
Off
Reserved
S5
Off
Off = Power-on password enabled
On = Power-on password disabled *
S6
Off
Off = Normal operation
On = BIOS will clear CMOS and
NVRAM *
S7
Off
Reserved
Component identification 12
Position
Default
Function
S8
Off
Reserved
* "On" activates the function.
NMI functionality
An NMI crash dump enables administrators to create crash dump files when a system is hung and not
responding to traditional debug mechanisms.
Crash dump log analysis is an essential part of diagnosing reliability problems, such as hangs in
operating systems, device drivers, and applications. Many crashes freeze a system, and the only
available action for administrators is to cycle the system power. Resetting the system erases any
information that could support problem analysis, but the NMI feature preserves that information by
performing a memory dump before a hard reset.
To force the OS to invoke the NMI handler and generate a crash dump log, the administrator can do any
of the following:
•
Short the NMI jumper pins
•
Press the NMI switch
•
Use the iLO Virtual NMI feature
For additional information, see the whitepaper on the HP website
(http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00797875/c00797875.pdf).
System board LEDs
Component identification 13
Item
LED description
Status
1
Processor failure
Amber = A multibit error has occurred.
Off = Normal
2
PPM failure
Amber = PPM has failed.
Off = Normal
3
Processor heatsink
fan failure
Amber = Processor heatsink fan has failed or is
missing.
Off = Normal
4
Reserved
—
5
Reserved
—
6
PCI fan failure
Amber = PCI fan has failed or is missing.
Off = Normal
7
Overtemperature
Amber = System has reached a cautionary or
critical temperature level.
Off = Normal
8
DIMM 4 failure
Amber = DIMM has failed or is missing.
Off = Normal
9
DIMM 3 failure
Amber = DIMM has failed or is missing.
Off = Normal
10
DIMM 2 failure
Amber = DIMM has failed or is missing.
Off = Normal
11
DIMM 1 failure
Amber = DIMM has failed or is missing.
Off = Normal
12
Rear fan failure
Amber = Rear fan has failed or is missing.
Off = Normal
System LEDs and internal health LED combinations
When the internal health LED on the front panel illuminates either amber or red, the server is experiencing
a health event. Combinations of illuminated system LEDs and the internal health LED indicate system
status.
NOTE: The system management driver must be installed for the internal system health LED to
provide pre-failure and warranty conditions.
The front panel health LEDs indicate only the current hardware status. In some situations, HP SIM may
report server status differently than the health LEDs because the software tracks more system attributes.
Component identification 14
System LED and
color
Internal health
LED color
Status
Processor failure
(Amber)
Red
One or more of the following conditions may exist:
•
Processor has failed.
•
Processor is not installed in the socket.
•
ROM detected a failed processor during POST.
Amber
Processor is in a pre-failure condition.
PPM failure (Amber)
Red
PPM has failed.
DIMM failure, slot X
(Amber)
Red
•
DIMM in slot X has failed.
•
DIMM has experienced a multi-bit error.
•
DIMM in slot X has reached single-bit correctable error
threshold.
•
DIMM in slot X is in a pre-failure condition.
•
No valid or usable memory is installed in the system.
•
The banks are not populated in the correct order.
Amber
DIMM failure (all
slots, Amber)
Red
Overtemperature
(Amber)
Red
System temperature has exceeded OS cautionary level or
critical hardware level.
Fan failure (Amber)
Red
A required fan has failed.
PCI-X extender board components
Item
Description
1
PCI-X expansion slot 1
2
System board connector
Component identification 15
Fan locations
Item
Description
1
Rear fan
2
Processor fan
3
PCI fan (optional)
Component identification 16
Operations
Power up the server
To power up the server, press the Power On/Standby button.
Press the F9 key, when prompted during the boot process, to access RBSU ("HP ROM-Based Setup Utility"
on page 47) and change the server settings. The system language default is English.
For more information on the automatic configuration, see the ROM-Based Setup Utility User Guide located
on the Documentation CD.
Power down the server
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some
internal circuitry remain active until AC power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server.
1.
Shut down the OS as directed by the OS documentation.
2.
Press the Power On/Standby button to place the server in standby mode. When the server enters
standby power mode, the system power LED changes to amber.
3.
Disconnect the power cords.
The system is now without power.
Operations 17
Unlock the bezel
Unlock and remove the bezel before accessing the hard drive cage and media bays. Unlock the bezel
before removing the access panel. Close and lock the bezel during normal server operations to ensure
proper cooling airflow.
Remove the bezel
Unlock and remove the bezel before accessing the hard drive cage and media bays. Unlock the bezel
before removing the access panel. Close and lock the bezel during normal server operations to ensure
proper cooling airflow.
To remove the component:
1.
Power down the server (on page 17).
2.
Unlock the bezel.
Operations 18
3.
Remove the bezel.
Remove the access panel
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Loosen the two thumbscrews.
4.
Slide the access panel toward the rear of the server and remove from the server.
After installing hardware options, install the access panel. Be sure that the panel is locked into place
securely before powering up the server.
Install the access panel
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
1.
Place the access panel on the chassis and slide it toward the front of the server.
2.
Tighten the two thumbscrews.
3.
Close the bezel ("Unlock the bezel" on page 18).
IMPORTANT: Be sure that the panel is locked into place securely before powering up the
server.
Operations 19
4.
Power up the server (on page 17).
Remove a media bay blank
1.
Power down the server (on page 17).
2.
Remove the front bezel ("Remove the bezel" on page 18).
3.
Remove a media bay blank.
Remove a bezel blank
1.
Power down the server (on page 17).
2.
Remove the front bezel ("Remove the bezel" on page 18).
3.
Remove a bezel blank.
Operations 20
Remove the system air baffle and PCI card guide
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove any full-length expansion boards installed in slot 1, 3, or 5, if installed ("Expansion boards"
on page 39).
5.
Disconnect the PCI fan cable, if installed ("System board components" on page 11).
6.
Remove the system air baffle and PCI card guide.
Operations 21
Setup
Optional installation services
Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and
running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you
integrate both hardware and software support into a single package. A number of service level options
are available to meet your needs.
HP Care Pack Services offer upgraded service levels to expand your standard product warranty with easyto-buy, easy-to-use support packages that help you make the most of your server investments. Some of the
Care Pack services are:
•
•
•
•
Hardware support
o
6-Hour Call-to-Repair
o
4-Hour 24x7 Same Day
o
4-Hour Same Business Day
Software support
o
Microsoft®
o
Linux
o
HP ProLiant Essentials (HP SIM and RDP)
Integrated hardware and software support
o
Critical Service
o
Proactive 24
o
Support Plus
o
Support Plus 24
Startup and implementation services for both hardware and software
For more information on Care Packs, refer to the HP website
(http://www.hp.com/hps/carepack/servers/cp_proliant.html).
Rack planning resources
The rack resource kit ships with all HP branded or Compaq branded 9000, 10000, and H9 series racks.
For more information on the content of each resource, refer to the rack resource kit documentation.
If you intend to deploy and configure multiple servers in a single rack, refer to the white paper on highdensity deployment at the HP website (http://www.hp.com/products/servers/platforms).
Setup
22
Optimum environment
When installing the server in a rack, select a location that meets the environmental standards described in
this section.
Space and airflow requirements
To allow for servicing and adequate airflow, observe the following space and airflow requirements when
deciding where to install a rack:
•
Leave a minimum clearance of 63.5 cm (25 in) in front of the rack.
•
Leave a minimum clearance of 76.2 cm (30 in) behind the rack.
•
Leave a minimum clearance of 121.9 cm (48 in) from the back of the rack to the back of another
rack or row of racks.
HP servers draw in cool air through the front door and expel warm air through the rear door. Therefore,
the front and rear rack doors must be adequately ventilated to allow ambient room air to enter the
cabinet, and the rear door must be adequately ventilated to allow the warm air to escape from the
cabinet.
CAUTION: To prevent improper cooling and damage to the equipment, do not block the
ventilation openings.
When vertical space in the rack is not filled by a server or rack component, the gaps between the
components cause changes in airflow through the rack and across the servers. Cover all gaps with
blanking panels to maintain proper airflow.
CAUTION: Always use blanking panels to fill empty vertical spaces in the rack. This
arrangement ensures proper airflow. Using a rack without blanking panels results in improper
cooling that can lead to thermal damage.
The 9000 and 10000 Series Racks provide proper server cooling from flow-through perforations in the
front and rear doors that provide 64 percent open area for ventilation.
CAUTION: When using a Compaq branded 7000 Series rack, you must install the high
airflow rack door insert [P/N 327281-B21 (42U) or P/N 157847-B21 (22U)] to provide
proper front-to-back airflow and cooling.
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure
adequate airflow and to prevent damage to the equipment:
• Front and rear doors—If the 42U rack includes closing front and rear doors, you must allow
5,350 sq cm (830 sq in) of holes evenly distributed from top to bottom to permit adequate
airflow (equivalent to the required 64 percent open area for ventilation).
• Side—The clearance between the installed rack component and the side panels of the rack
must be a minimum of 7 cm (2.75 in).
Temperature requirements
To ensure continued safe and reliable equipment operation, install or position the system in a wellventilated, climate-controlled environment.
Setup
23
The maximum recommended ambient operating temperature (TMRA) for most server products is 35°C
(95°F). The temperature in the room where the rack is located must not exceed 35°C (95°F).
CAUTION: To reduce the risk of damage to the equipment when installing third-party options:
• Do not permit optional equipment to impede airflow around the server or to increase the
internal rack temperature beyond the maximum allowable limits.
• Do not exceed the manufacturer’s TMRA.
Power requirements
Installation of this equipment must comply with local and regional electrical regulations governing the
installation of information technology equipment by licensed electricians. This equipment is designed to
operate in installations covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992
(code for Protection of Electronic Computer/Data Processing Equipment). For electrical power ratings on
options, refer to the product rating label or the user documentation supplied with that option.
WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not
overload the AC supply branch circuit that provides power to the rack. Consult the electrical
authority having jurisdiction over wiring and installation requirements of your facility.
CAUTION: Protect the server from power fluctuations and temporary interruptions with a
regulating uninterruptible power supply (UPS). This device protects the hardware from damage
caused by power surges and voltage spikes and keeps the system in operation during a power
failure.
When installing more than one server, you may need to use additional power distribution devices to
safely provide power to all devices. Observe the following guidelines:
•
Balance the server power load between available AC supply branch circuits.
•
Do not allow the overall system AC current load to exceed 80 percent of the branch circuit AC
current rating.
•
Do not use common power outlet strips for this equipment.
•
Provide a separate electrical circuit for the server.
Electrical grounding requirements
The server must be grounded properly for proper operation and safety. In the United States, you must
install the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250,
as well as any local and regional building codes. In Canada, you must install the equipment in
accordance with Canadian Standards Association, CSA C22.1, Canadian Electrical Code. In all other
countries, you must install the equipment in accordance with any regional or national electrical wiring
codes, such as the International Electrotechnical Commission (IEC) Code 364, parts 1 through 7.
Furthermore, you must be sure that all power distribution devices used in the installation, such as branch
wiring and receptacles, are listed or certified grounding-type devices.
Because of the high ground-leakage currents associated with multiple servers connected to the same
power source, HP recommends the use of a PDU that is either permanently wired to the building’s branch
circuit or includes a nondetachable cord that is wired to an industrial-style plug. NEMA locking-style plugs
or those complying with IEC 60309 are considered suitable for this purpose. Using common power outlet
strips for the server is not recommended.
Setup
24
Warnings and cautions
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling jacks are extended to the floor.
• The full weight of the rack rests on the leveling jacks.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
WARNING: To reduce the risk of personal injury or equipment damage when unloading a
rack:
• At least two people are needed to safely unload the rack from the pallet. An empty 42U
rack can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and
may become unstable when being moved on its casters.
• Never stand in front of the rack when it is rolling down the ramp from the pallet. Always
handle the rack from both sides.
WARNING: When installing a server in a telco rack, be sure that the rack frame is adequately
secured to the top and bottom of the building structure.
WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the
equipment:
• Observe local occupational health and safety requirements and guidelines for manual
material handling.
• Get help to lift and stabilize the product during installation or removal, especially when the
product is not fastened to the rails. When the server weighs more than 22.5 kg (50 lb), at
least two people must lift the server into the rack together. A third person may be required
to help align the server if the server is installed higher than chest level.
• Use caution when installing the server in or removing the server from the rack; it is unstable
when not fastened to the rails.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some
internal circuitry remain active until AC power is removed.
CAUTION: Protect the server from power fluctuations and temporary interruptions with a
regulating uninterruptible power supply (UPS). This device protects the hardware from damage
caused by power surges and voltage spikes and keeps the system in operation during a power
failure.
Setup
25
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
Identifying server shipping carton contents
Unpack the server shipping carton and locate the materials and documentation necessary for installing the
server.
The contents of the server shipping carton include:
•
Server
•
Power cord
•
Keyboard and mouse (not included in all configurations)
•
Hardware documentation, Documentation CD, and software media
In addition to the supplied items, you may need:
•
Optional hard drives, array controllers, and tape drives
•
Operating system or application software
•
UPS or PDU
Installing hardware options
Install any hardware options before initializing the server. For options installation information, refer to the
option documentation. For server-specific information, refer to "Hardware options installation (on page
29)."
Setting up a server
To install the server in a rack, use the rack enabling kit for HP servers. For more information, contact an
HP authorized reseller ("HP contact information" on page 85).
1.
Place the server on a flat, level work surface.
2.
Connect peripheral devices to the server.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not plug
telephone or telecommunications connectors into RJ-45 connectors.
Setup
26
The server may look different from that shown.
Item
Description
1
Power supply connector
2
Mouse connector
3
Keyboard connector
4
10/100/1000 NIC 1 connector
5
iLO 2 management port
6
USB connectors (2)
7
Video connector
8
Serial connector
1.
Connect the power cord to the rear of the server.
2.
Connect the power cord to the AC power source.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against
it. Pay particular attention to the plug, electrical outlet, and the point where the cord
extends from the server.
Installing the operating system
To operate properly, the server must have a supported operating system. For the latest information on
supported operating systems, refer to the HP website (http://www.hp.com/go/supportos).
Setup
27
Two methods are available to install an operating system on the server:
•
SmartStart assisted installation—Insert the SmartStart CD into the CD-ROM drive and reboot the
server.
•
Manual installation—Insert the operating system CD into the CD-ROM drive and reboot the server.
This process may require you to obtain additional drivers from the HP website
(http://www.hp.com/support).
Follow the on-screen instructions to begin the installation process.
For information on using these installation paths, refer to the SmartStart installation poster in the HP
ProLiant Essentials Foundation Pack, included with the server.
For embedded SATA RAID configuration, the administrator must create a driver diskette and perform a
manual OS installation.
To install the embedded SATA RAID driver during OS installation, see "Installing an operating system
(Embedded SATA RAID) (on page 51)."
Registering the server
To register the server, refer to the HP Registration website (http://register.hp.com).
Setup
28
Hardware options installation
Introduction
If more than one option is being installed, read the installation instructions for all the hardware options
and identify similar steps to streamline the installation process.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: To prevent damage to electrical components, properly ground the server before
beginning any installation procedure. Improper grounding can cause electrostatic discharge.
Memory
You can expand server memory by installing PC2-6400 DDR2 SDRAM DIMMs. The system supports up to
four DIMMs for a maximum of 8 GB.
For DIMM slot locations and bank assignments, see "System board components (on page 11)."
DIMM installation guidelines
Observe the following guidelines when installing additional memory:
•
DIMMs installed in the server must be unbuffered DDR2 SDRAM with ECC.
•
If only a single DIMM is installed, it must be installed in slot 1A.
•
All DIMMs installed must be the same speed.
BIOS detects the DIMM population and sets the system as follows:
•
Single-bank mode: Single DIMM installed in one bank only
•
Single-bank interleaved mode: DIMMs installed in one bank with equal capacities per slot
•
Dual-bank asymmetric mode: DIMMs installed in both banks, but of unequal capacities per bank
•
Dual-bank interleaved mode: DIMMs installed in both banks with equal capacities per bank
The following table lists some, but not all, possible configurations. For best performance, HP recommends
dual-bank interleaved mode configurations.
Slot 1A
Slot 2B
Slot 3A
Slot 4B
Total memory
Mode
512 MB
—
—
—
512 MB
Single-bank
512 MB
—
512 MB
—
1 GB
Single-bank interleaved
1 GB
—
—
—
1 GB
Single-bank
1 GB
—
1 GB
—
2 GB
Single-bank interleaved
Hardware options installation
29
Slot 1A
Slot 2B
Slot 3A
Slot 4B
Total memory
Mode
2 GB
—
—
—
2 GB
Single-bank
2 GB
—
2 GB
—
4 GB
Single-bank interleaved
2 GB
2 GB
2 GB
—
6 GB
Dual-bank asymmetric
2 GB
2 GB
2 GB
2 GB
8 GB
Dual-bank interleaved
Installing DIMMs
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Open the DIMM slot latches.
5.
Install the DIMM.
6.
Install the access panel (on page 19).
7.
Lock the bezel.
8.
Power up the server (on page 17).
Hard drives
The server supports non-hot-plug SATA hard drives.
Optional hot-plug SATA or SAS hard drives may be supported in select configurations ("SAS controller"
on page 42).
The SATA RAID feature supports the following configurations:
•
Two RAID volumes with two hard drives per volume
•
One RAID volume with four hard drives
Hardware options installation
30
Hot-plug SATA and hot-plug SAS hard drives can be used interchangeably when a SAS controller is
installed. Before installing a SAS hard drive, you must install a SAS controller ("SAS controller" on page
42). A SATA controller is embedded for use with SATA drives only.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
To install the component:
1.
Remove the bezel (on page 18).
2.
Remove the hard drive blank.
3.
Open the release latch to prepare the drive for installation.
Hardware options installation
31
4.
Install the hard drive.
5.
Determine the status of the hard drive from the hot-plug SAS hard drive LED combinations ("Hot-plug
SATA or SAS hard drive LEDs" on page 8).
6.
Install the bezel.
7.
Resume normal server operations.
SATA optical drive
For clarity, the following illustrations include option cabling only.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
To install the component:
1.
Power down the server (on page 17).
2.
Remove the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the applicable media bay blank ("Remove a media bay blank" on page 20).
Hardware options installation
32
5.
Install the optical drive.
6.
Connect the power cable to the rear of the drive.
7.
Connect the optical drive cable to the rear of the optical drive and to the optical drive cable
connector on the system board.
8.
Remove the applicable bezel blank from the bezel ("Remove a bezel blank" on page 20).
9.
Install the access panel (on page 19).
10.
Install the bezel.
11.
Power up the server (on page 17).
USB tape drive
For clarity, the following illustrations include option cabling only.
Hardware options installation
33
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
To install the component:
1.
Power down the server (on page 17).
2.
Remove the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the applicable media bay blank ("Remove a media bay blank" on page 20).
5.
Install the tape drive.
6.
Connect the USB tape drive cable to the USB tape drive cable connector on the system board.
7.
Remove the applicable bezel blank from the bezel ("Remove a bezel blank" on page 20).
8.
Install the access panel (on page 19).
9.
Install the bezel.
Hardware options installation
34
10.
Power up the server (on page 17).
Full-height tape drive
For clarity, the following illustrations include option cabling only.
To install the component:
1.
Power down the server (on page 17).
2.
Remove the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the applicable media bay blanks ("Remove a media bay blank" on page 20).
5.
Disengage the two wire supports inside the half-height drive bays.
6.
Install the tape drive:
a. Open the upper and lower wire retainers.
b. Install the full-height tape drive.
Hardware options installation
35
c.
7.
Close the upper and lower wire retainers.
Install the retaining screw.
IMPORTANT: When installing a SCSI tape drive, an optional SCSI HBA controller is required.
8.
Install a SCSI controller ("Installing expansion boards" on page 40).
9.
Connect the power cable to the rear of the drive.
Hardware options installation
36
10.
Connect the data cable to the rear of the drive and to the SCSI controller.
11.
Remove the applicable bezel blanks from the bezel ("Remove a bezel blank" on page 20).
12.
Install the access panel (on page 19).
13.
Install the bezel.
14.
Power up the server (on page 17).
Diskette drives
A diskette drive can be installed in the server in the following ways:
•
Install a diskette drive in the chassis ("Installing a legacy diskette drive" on page 37)
•
Install a diskette drive using a USB cable (when using operating systems that support USB)
("Installing a USB diskette drive" on page 39)
Installing a legacy diskette drive
For clarity, the following illustrations include option cabling only.
1.
Power down the server (on page 17).
2.
Remove the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the applicable media bay blank ("Remove a media bay blank" on page 20).
Hardware options installation
37
5.
Install the diskette drive.
6.
Connect the power cable to the rear of the drive.
7.
Connect the diskette drive cable to the rear of the diskette drive and to the diskette drive cable
connector on the system board.
8.
Remove the applicable bezel blank from the bezel ("Remove a bezel blank" on page 20).
9.
Install the access panel (on page 19).
10.
Install the bezel.
11.
Power up the server (on page 17).
Hardware options installation
38
Installing a USB diskette drive
Connect a USB diskette drive to the USB connector on the server front panel.
Expansion boards
The server supports PCI Express and PCI-X expansion boards. Slot 1 is located on the optional PCI-X
extender board (on page 41).
Slot
Expansion
card type
Connector
Maximum speed
1
PCI-X (optional)
64 bit, 3.3 V
100 MHz
2
Not supported
—
—
3
PCIe
x8
x8
4
Reserved
—
—
5
PCIe
x8
x1
6
PCIe
x8
x1
7
PCIe
x8
x1
Removing the expansion slot cover
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
Hardware options installation
39
4.
Remove the expansion slot cover.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all PCI slots have either an expansion slot cover or an expansion board installed.
Installing expansion boards
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the expansion boards.
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the expansion slot cover ("Removing the expansion slot cover" on page 39).
5.
Install the expansion board, and press firmly to seat the board in the connector.
Hardware options installation
40
6.
Close the PCI retainer.
7.
Connect any required internal or external cables to the expansion board. See the documentation that
ships with the expansion board.
8.
Install the access panel (on page 19).
9.
Install the bezel ("Remove the bezel" on page 18).
10.
Power up the server (on page 17).
PCI-X extender board
To install the component:
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the system air baffle and PCI card guide (on page 21).
5.
Install the PCI-X extender board and secure the four T-15 screws.
Hardware options installation
41
6.
Install the PCI fan.
7.
Install the system air baffle and PCI card guide.
8.
Connect the PCI fan cable to the PCI fan connector on the system board ("System board
components" on page 11).
9.
Install the PCI-X expansion board in slot 1, as needed ("Installing expansion boards" on page 40).
10.
Install the access panel (on page 19).
11.
Lock the bezel.
12.
Power up the server (on page 17).
SAS controller
To install the component:
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the expansion slot cover ("Removing the expansion slot cover" on page 39).
5.
Install the SAS controller ("Installing expansion boards" on page 40).
6.
Disconnect the SATA cable from the hard drive backplane and the system board.
7.
Connect the SAS cable to the hard drive backplane and to the SAS controller ("SAS hard drive
cabling" on page 45).
8.
Install the access panel (on page 19).
9.
Lock the bezel.
10.
Power up the server (on page 17).
Parallel and second serial connector
To install the component:
Hardware options installation
42
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the expansion slot cover that corresponds to the parallel and serial connector ("Removing
the expansion slot cover" on page 39).
5.
Install the parallel and serial connector bracket.
6.
Connect the parallel and serial cables to the parallel and serial connectors on the system board.
7.
Close the PCI retainer.
8.
Install the access panel (on page 19).
9.
Lock the bezel.
10.
Power up the server (on page 17).
11.
Enable the feature under the System Options menu in RBSU. For more information on RBSU, refer to
the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website
(http://www.hp.com/servers/smartstart).
Hardware options installation
43
Cabling
Server cabling
Item
Description
1
SATA hard drive cable (hard drive)
2
Front USB cable
3
SATA optical drive cable
4
Front panel LED cable
Cabling 44
SATA hard drive cabling
Item
Description
1
Power cable
2
SATA cable
SAS hard drive cabling
Item
Description
1
Power cable
2
SAS cable
Cabling 45
Software and configuration utilities
Configuration tools
SmartStart software
SmartStart is a collection of software that optimizes single-server setup, providing a simple and consistent
way to deploy server configuration. SmartStart has been tested on many ProLiant server products,
resulting in proven, reliable configurations.
SmartStart assists the deployment process by performing a wide range of configuration activities,
including:
•
Configuring hardware using embedded configuration utilities, such as RBSU and ORCA
•
Preparing the system for installing "off-the-shelf" versions of leading operating system software
•
Installing optimized server drivers, management agents, and utilities automatically with every
assisted installation
•
Testing server hardware using the Insight Diagnostics Utility ("HP Insight Diagnostics" on page 55)
•
Installing software drivers directly from the CD. With systems that have internet connection, the
SmartStart Autorun Menu provides access to a complete list of ProLiant system software.
•
Enabling access to the Array Configuration Utility (on page 48), Array Diagnostic Utility, and Erase
Utility (on page 53)
SmartStart is included in the HP ProLiant Essentials Foundation Pack. For more information about
SmartStart software, refer to the HP ProLiant Essentials Foundation Pack or the HP website
(http://h18013.www1.hp.com/products/servers/management/smartstart/index.html).
SmartStart Scripting Toolkit
The SmartStart Scripting Toolkit is a server deployment product that delivers an unattended automated
installation for high-volume server deployments. The SmartStart Scripting Toolkit is designed to support
ProLiant BL, ML, and DL servers. The toolkit includes a modular set of utilities and important documentation
that describes how to apply these new tools to build an automated server deployment process.
Using SmartStart technology, the Scripting Toolkit provides a flexible way to create standard server
configuration scripts. These scripts are used to automate many of the manual steps in the server
configuration process. This automated server configuration process cuts time from each server deployed,
making it possible to scale server deployments to high volumes in a rapid manner.
For more information, and to download the SmartStart Scripting Toolkit, refer to the HP website
(http://www.hp.com/servers/sstoolkit).
Software and configuration utilities 46
Configuration Replication Utility
CONREP is shipped in the SmartStart Scripting Toolkit and is a program that works with RBSU to replicate
hardware configuration on ProLiant servers. This utility is run during State 0, Run Hardware Configuration
Utility, when doing a scripted server deployment. CONREP reads the state of the system environment
variables to determine the configuration and then writes the results to an editable script file. This file can
then be deployed across multiple servers with similar hardware and software components. For more
information, refer to the SmartStart Scripting Toolkit User Guide on the HP website
(http://h18004.www1.hp.com/products/servers/management/toolkit/documentation.html).
HP ROM-Based Setup Utility
RBSU is a configuration utility embedded in ProLiant servers that performs a wide range of configuration
activities that can include the following:
•
Configuring system devices and installed options
•
Enabling and disabling system features
•
Displaying system information
•
Selecting the primary boot controller
•
Configuring memory options
•
Language selection
For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD
or the HP website (http://www.hp.com/support/smartstart/documentation).
Using RBSU
To use RBSU, use the following keys:
•
To access RBSU, press the F9 key during power-up when prompted.
•
To navigate the menu system, use the arrow keys.
•
To make selections, press the Enter key.
•
To access Help for a highlighted configuration option, press the F1 key.
IMPORTANT: RBSU automatically saves settings when you press the Enter key. The utility does
not prompt you for confirmation of settings before you exit the utility. To change a selected
setting, you must select a different setting and press the Enter key.
Default configuration settings are applied to the server at one of the following times:
•
Upon the first system power-up
•
After defaults have been restored
Default configuration settings are sufficient for proper typical server operation, but configuration settings
can be modified using RBSU. The system will prompt you for access to RBSU with each power-up.
Auto-configuration process
The auto-configuration process automatically runs when you boot the server for the first time. During the
power-up sequence, the system ROM automatically configures the entire system without needing any
Software and configuration utilities 47
intervention. During this process, the ORCA utility, in most cases, automatically configures the array to a
default setting based on the number of drives connected to the server.
NOTE: The server may not support all the following examples.
NOTE: If the boot drive is not empty or has been written to in the past, ORCA does not
automatically configure the array. You must run ORCA to configure the array settings.
Drives installed
Drives used
RAID level
1
1
RAID 0
2
2
RAID 1
3, 4, 5, or 6
3, 4, 5, or 6
RAID 5
More than 6
0
None
To change any ORCA default settings and override the auto-configuration process, press the F8 key when
prompted.
By default, the auto-configuration process configures the system for the English language. To change any
default settings in the auto-configuration process (such as the settings for language, operating system, and
primary boot controller), execute RBSU by pressing the F9 key when prompted. After the settings are
selected, exit RBSU and allow the server to reboot automatically.
For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD
or the HP website (http://www.hp.com/support/smartstart/documentation).
Boot options
Near the end of the boot process, the boot options screen is displayed. This screen is visible for several
seconds before the system attempts to boot from a diskette, CD, or hard drive. During this time, you can
do the following:
•
Access RBSU by pressing the F9 key
•
Access the System Maintenance Menu (which enables you to launch ROM-based Diagnostics or
Inspect) by pressing the F10 key
•
Force a PXE Network boot by pressing the F12 key
BIOS Serial Console
BIOS Serial Console allows you to configure the serial port to view POST error messages and run RBSU
remotely through a serial connection to the server COM port. The server that you are remotely configuring
does not require a keyboard and mouse.
For more information about BIOS Serial Console, see the BIOS Serial Console User Guide on the
Documentation CD or the HP website (http://www.hp.com/support/smartstart/documentation).
Array Configuration Utility
ACU is a browser-based utility with the following features:
•
Runs as a local application or remote service
Software and configuration utilities 48
•
Supports online array capacity expansion, logical drive extension, assignment of online spares, and
RAID or stripe size migration
•
Suggests the optimum configuration for an unconfigured system
•
Provides different operating modes, enabling faster configuration or greater control over the
configuration options
•
Remains available any time that the server is on
•
Displays on-screen tips for individual steps of a configuration procedure
For optimum performance, the minimum display settings are 800 × 600 resolution and 256 colors.
Servers running Microsoft® operating systems require Internet Explorer 5.5 (with Service Pack 1) or later.
For Linux servers, refer to the README.TXT file for additional browser and support information.
For more information, refer to the Configuring Arrays on HP Smart Array Controllers Reference Guide on
the Documentation CD or the HP website (http://www.hp.com).
Embedded SATA RAID
HP provides the SATA RAID feature through use of the Adaptec Storage Manager. This feature enables
RAID functionality (RAID 0, RAID 1, or RAID 10) for the embedded SATA controller in the system.
Required hardware
Installing the SATA RAID driver may require a diskette drive and CD-ROM drive. Some servers do not ship
with these drives as standard hardware.
NOTE: Systems with Microsoft® Windows Server™ 2003 and HP embedded drivers do not
require additional hardware.
Diskette and CD-ROM drive options
To acquire a diskette drive option or CD-ROM drive option for a server, contact an HP authorized reseller.
For the name of the nearest HP authorized reseller:
•
In the United States, call 1-800-345-1518.
•
In Canada, call 1-800-263-5868.
•
In other locations, refer to the HP website (http://www.hp.com).
USB diskette and CD-ROM drives
For driver installation purposes, a USB diskette drive and USB CD-ROM drive are sufficient.
NOTE: To use a USB drive key in place of the diskette drive, see "Using a USB drive key as a
virtual driver diskette (on page 55)."
HP provides both standard USB support and legacy USB support. Standard support is provided by the OS
through the appropriate USB device drivers. Before the OS loads, HP provides support for USB devices
through legacy USB support, which is enabled by default in the system ROM. HP hardware supports USB
version 1.1 or 2.0, depending on the version of the hardware.
Software and configuration utilities 49
Legacy USB support provides USB functionality in environments where USB support is normally not
available. Specifically, HP provides legacy USB functionality for:
•
POST
•
RBSU
•
Diagnostics
•
DOS
•
Operating environments which do not provide native USB support
For more information on ProLiant USB support, refer to the HP website
(http://h18004.www1.hp.com/products/servers/platforms/usb-support.html).
HP Integrated Lights-Out Virtual Floppy and CD-ROM drives
iLO 2 Advanced provides diskette drive and CD-ROM drive functionality through the iLO 2 Virtual Floppy
and CD-ROM features.
For detailed information about iLO 2 Advanced, refer to the HP Integrated Lights-Out User Guide on the
HP website (http://www.hp.com/servers/lights-out).
Configuring the embedded SATA RAID feature
CAUTION: Back up any data stored on the hard drives before proceeding. The configuration
process erases all data on the hard drives.
1.
Power up the server (on page 17).
2.
Press the F9 key to launch RBSU.
NOTE: Enabling the RAID option in RBSU is only necessary for installation of the RAID driver.
If this option is not enabled, the OS loads the standard ATA driver from the OS media.
3.
Select Advanced Options>Embedded SATA RAID>Enable RAID.
4.
Press the F10 key twice to exit RBSU. The system automatically reboots.
5.
After the system reboots, press the F8 key to enter the HP Embedded SATA setup utility.
6.
Select Array Configuration Utility from the Option menu.
7.
Select Create Array from the main menu.
8.
Select the SATA drives that will be included in the RAID set by pressing the INS key.
9.
Press the Enter key to complete selection. The system prompts a selection of the RAID level.
10.
Select the preferred RAID level.
11.
Enter an Array Label and press Enter. If RAID 0 is selected, select a Stripe Size.
12.
Select how you would like to create the array. Choose "Quick Init" to shorten the amount of time it
takes to create the array.
NOTE: For more information, see the HP Embedded SATA RAID Controller User Guide at the
HP website
(http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?&lang=en&cc=us&prodTy
peId=15351).
13.
After the configuration is complete, select Done.
Software and configuration utilities 50
14.
Press the Esc key to exit the utility.
Installing an operating system (Embedded SATA RAID)
Embedded SATA RAID is only supported with the following operating systems:
•
Microsoft® Windows Server™ 2003
•
Red Hat Enterprise Linux 3
•
Red Hat Enterprise Linux 4
•
SUSE Linux Enterprise Server 9
For more information about supported operating systems, see the HP website
(http://www.hp.com/go/supportos).
To install an OS, download the HP embedded SATA RAID Controller driver and create a driver diskette
with the software and instructions from the HP website (http://www.hp.com/support).
SmartStart does not support assisted installation of an OS on servers configured with SATA RAID.
After inserting the SmartStart CD in the CD-ROM drive, a warning may indicate that the primary controller
is not supported by this version of the SmartStart software.
Installing HP Storage Manager
The HP Storage Manager utility enables administrators to create and manage arrays without rebooting
the server to access the BIOS utility.
For more information on embedded SATA RAID, see the HP Storage Manager HostRAID User Guide
located on the Documentation CD.
Option ROM Configuration for Arrays
Before installing an operating system, you can use the ORCA utility to create the first logical drive, assign
RAID levels, and establish online spare configurations.
The utility also provides support for the following functions:
•
Reconfiguring one or more logical drives
•
Viewing the current logical drive configuration
•
Deleting a logical drive configuration
•
Setting the controller to be the boot controller
If you do not use the utility, ORCA will default to the standard configuration.
For more information regarding array controller configuration, refer to the controller user guide.
For more information regarding the default configurations that ORCA uses, refer to the HP ROM-Based
Setup Utility User Guide on the Documentation CD.
HP ProLiant Essentials Rapid Deployment Pack
The RDP software is the preferred method for rapid, high-volume server deployments. The RDP software
integrates two powerful products: Altiris Deployment Solution and the HP ProLiant Integration Module.
Software and configuration utilities 51
The intuitive graphical user interface of the Altiris Deployment Solution console provides simplified pointand-click and drag-and-drop operations that enable you to deploy target servers, including server blades,
remotely. It enables you to perform imaging or scripting functions and maintain software images.
For more information about the RDP, refer to the HP ProLiant Essentials Rapid Deployment Pack CD or
refer to the HP website (http://www.hp.com/servers/rdp).
Re-entering the server serial number and product ID
After you replace the system board, you must re-enter the server serial number and the product ID.
1.
During the server startup sequence, press the F9 key to access RBSU.
2.
Select the System Options menu.
3.
Select Serial Number. The following warning is displayed:
WARNING! WARNING! WARNING! The serial number is loaded into the system
during the manufacturing process and should NOT be modified. This option
should only be used by qualified service personnel. This value should
always match the serial number sticker located on the chassis.
4.
Press the Enter key to clear the warning.
5.
Enter the serial number and press the Enter key.
6.
Select Product ID.
7.
Enter the product ID and press the Enter key.
8.
Press the Esc key to close the menu.
9.
Press the Esc key to exit RBSU.
10.
Press the F10 key to confirm exiting RBSU. The server will automatically reboot.
Management tools
Automatic Server Recovery
ASR is a feature that causes the system to restart when a catastrophic operating system error occurs, such
as a blue screen, ABEND, or panic. A system fail-safe timer, the ASR timer, starts when the System
Management driver, also known as the Health Driver, is loaded. When the operating system is
functioning properly, the system periodically resets the timer. However, when the operating system fails,
the timer expires and restarts the server.
ASR increases server availability by restarting the server within a specified time after a system hang or
shutdown. At the same time, the HP SIM console notifies you by sending a message to a designated
pager number that ASR has restarted the system. You can disable ASR from the HP SIM console or
through RBSU.
ROMPaq utility
The ROMPaq utility enables you to upgrade the system firmware (BIOS) or Lights-Out 100 firmware. To
upgrade the firmware, insert a ROMPaq diskette into the diskette drive or ROMPaq USB Key into an
available USB port and boot the system.
The ROMPaq utility checks the system and provides a choice (if more than one exists) of available
firmware revisions.
Software and configuration utilities 52
For more information about the ROMPaq utility, see the HP website (http://www.hp.com/go/support).
Integrated Lights-Out 2 technology
The iLO 2 subsystem is a standard component of selected ProLiant servers that provides server health and
remote server manageability. The iLO 2 subsystem includes an intelligent microprocessor, secure memory,
and a dedicated network interface. This design makes iLO 2 independent of the host server and its
operating system. The iLO 2 subsystem provides remote access to any authorized network client, sends
alerts, and provides other server management functions.
Using iLO 2, you can:
•
Remotely power up, power down, or reboot the host server.
•
Send alerts from iLO 2 regardless of the state of the host server.
•
Access advanced troubleshooting features through the iLO 2 interface.
•
Diagnose iLO 2 using HP SIM through a web browser and SNMP alerting.
For more information about iLO 2 features, refer to the iLO 2 documentation on the Documentation CD or
on the HP website (http://www.hp.com/servers/lights-out).
Erase Utility
CAUTION: Perform a backup before running the System Erase Utility. The utility sets the system
to its original factory state, deletes the current hardware configuration information, including
array setup and disk partitioning, and erases all connected hard drives completely. Refer to the
instructions for using this utility.
Run the Erase Utility if you must erase the system for the following reasons:
•
You want to install a new operating system on a server with an existing operating system.
•
You encounter an error when completing the steps of a factory-installed operating system installation.
The Erase Utility can be accessed from the Maintenance Utilities menu of the SmartStart CD ("SmartStart
software" on page 46).
Management Agents
Management Agents provide the information to enable fault, performance, and configuration
management. The agents allow easy manageability of the server through HP SIM software, and thirdparty SNMP management platforms. Management Agents are installed with every SmartStart assisted
installation or can be installed through the HP PSP. The Systems Management homepage provides status
and direct access to in-depth subsystem information by accessing data reported through the Management
Agents. For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation
Pack or the HP website (http://www.hp.com/servers/manage).
HP Systems Insight Manager
HP SIM is a web-based application that allows system administrators to accomplish normal administrative
tasks from any remote location, using a web browser. HP SIM provides device management capabilities
that consolidate and integrate management data from HP and third-party devices.
Software and configuration utilities 53
IMPORTANT: You must install and use HP SIM to benefit from the Pre-Failure Warranty for
processors, SAS and SCSI hard drives, and memory modules.
For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack or
the HP SIM website (http://www.hp.com/go/hpsim).
USB support
HP provides both standard USB support and legacy USB support. Standard support is provided by the
operating system through the appropriate USB device drivers. HP provides support for USB devices before
the operating system loads through legacy USB support, which is enabled by default in the system ROM.
HP hardware supports USB version 1.1.
Legacy USB support provides USB functionality in environments where USB support is normally not
available. Specifically, HP provides legacy USB functionality at:
•
POST
•
RBSU
•
Diagnostics
•
DOS
•
Environments which do not support USB natively
For more information on ProLiant USB support, refer to the HP website
(http://www.compaq.com/products/servers/platforms/usb-support.html).
Internal USB functionality
An internal USB connector is available for use with security key devices and USB drive keys. This solution
provides for use of a permanent USB key installed in the internal connector, avoiding issues of clearance
on the front of the rack and physical access to secure data.
For additional security, external USB functionality can be disabled through RBSU. Disabling external USB
support in RBSU disables the USB connectors on the local I/O cable. Internal USB functionality is
unaffected.
ROM legacy USB support
When using operating systems that support USB, the server supports USB devices, including, but not
limited to:
•
CD-ROM drives
•
Diskette drives
•
Keyboard
•
Mouse
For other operating systems, the ROM provides USB support for a keyboard, mouse, and diskette drives,
which do not support USB, but not for CD-ROM drives.
ROM legacy USB support is available during POST and while the operating system is running. The
maximum device support is two USB keyboards, two USB mouse devices, and one layer of hubs.
Software and configuration utilities 54
Using a USB drive key as a virtual driver diskette
Administrators performing a Microsoft® Windows Server™ 2003 OS installation can use a USB drive
key instead of a conventional driver diskette. This method eliminates the need for a local diskette and
does not interrupt the OS installation process. Also, the USB drive key eliminates the need for the
administrator to press the F6 key during a Windows Server™ 2003 installation.
To create a Windows Server™ 2003 driver diskette image on a USB key:
1.
Download the HP Drive Key Boot Utility from the HP website (http://www.hp.com/go/support).
2.
Using the HP Drive Key Utility, replicate a previously-created Windows Server™ 2003 driver diskette
with the necessary drivers.
a. Select Create New or Replace Existing Configuration.
b. Select Floppy Disk option.
c.
Select the Image from drive option. This image is from the previously-created driver diskette
containing the necessary drivers to be placed on the USB key.
3.
Insert the USB drive key into any server USB connector and a Windows Server™ 2003 installation
CD into the CD-ROM drive.
4.
Power up the server (on page 17).
5.
Boot the CD-ROM and begin the OS installation.
The Windows Server™ 2003 installation CD should automatically find and install the necessary boot
controller drivers from the USB drive key.
Diagnostic tools
HP Insight Diagnostics
HP Insight Diagnostics is a proactive server management tool, available in both offline and online
versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify
server installations, troubleshoot problems, and perform repair validation.
HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the
OS is not running. To run this utility, launch the SmartStart CD.
HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and
other related data needed for effective server management. Available in Microsoft® Windows® and
Linux versions, the utility helps to ensure proper system operation.
For more information or to download the utility, refer to the HP website
(http://www.hp.com/servers/diags).
HP Insight Diagnostics survey functionality
HP Insight Diagnostics (on page 55) provides survey functionality that gathers critical hardware and
software information on ProLiant servers.
This functionality supports operating systems that may not be supported by the server. For operating
systems supported by the server, see the HP website (http://www.hp.com/go/supportos).
Software and configuration utilities 55
If a significant change occurs between data-gathering intervals, the survey function marks the previous
information and overwrites the survey data files to reflect the latest changes in the configuration.
Survey functionality is installed with every SmartStart-assisted HP Insight Diagnostics installation, or it can
be installed through the HP PSP ("ProLiant Support Packs" on page 57).
NOTE: The current version of SmartStart provides the memory spare part numbers for the
server. To download the latest version, see the HP website (http://www.hp.com/support).
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each
event with 1-minute granularity.
You can view recorded events in the IML in several ways, including the following:
•
From within HP SIM ("HP Systems Insight Manager" on page 53)
•
From within Survey Utility
•
From within operating system-specific IML viewers
o
For NetWare: IML Viewer
o
For Windows®: IML Viewer
o
For Linux: IML Viewer Application
•
From within the iLO 2 user interface
•
From within HP Insight Diagnostics (on page 55)
For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack.
ROMPaq disaster recovery
If the current version of the ROM is corrupt, perform ROMPaq disaster recovery procedures:
1.
Create a ROMPaq diskette using the Autorun Menu on the SmartStart CD.
2.
Power down the server (on page 17).
3.
Insert the ROMPaq diskette.
4.
Power up the server (on page 17).
a. The server generates one long beep and two short beeps to indicate that you are in disaster
recovery mode. If the diskette is not in place, the system continues to beep until a valid ROMPaq
diskette is inserted.
b. The ROMPaq diskette flashes the system ROM image. If successful, a sequence of ascending
audible beeps is generated. If unsuccessful, a sequence of descending audible beeps is
generated and you need to repeat the disaster recovery process.
5.
Power down the server (on page 17).
6.
Remove the ROMPaq diskette.
7.
Power up the server (on page 17).
Software and configuration utilities 56
Keeping the system current
Drivers
The server includes new hardware that may not have driver support on all operating system installation
media.
If you are installing a SmartStart-supported operating system, use the SmartStart software (on page 46)
and its Assisted Path feature to install the operating system and latest driver support.
NOTE: If you are installing drivers from the SmartStart CD or the Software Maintenance CD,
refer to the SmartStart website (http://www.hp.com/servers/smartstart) to be sure that you are
using the latest version of SmartStart. For more information, refer to the documentation
provided with the SmartStart CD.
If you do not use the SmartStart CD to install an operating system, drivers for some of the new hardware
are required. These drivers, as well as other option drivers, ROM images, and value-add software can be
downloaded from the HP website (http://www.hp.com/support).
IMPORTANT: Always perform a backup before installing or updating device drivers.
ProLiant Support Packs
PSPs represent operating system-specific bundles of ProLiant optimized drivers, utilities, and management
agents. Refer to the PSP website
(http://h18000.www1.hp.com/products/servers/management/psp.html).
Operating system version support
Refer to the operating system support matrix (http://www.hp.com/go/supportos).
HP Smart Update Manager
The HP Smart Update Manager enables system administrators to upgrade ROM images efficiently across
a wide range of servers and options. This tool has the following features:
•
Works offline and online
•
Supports Microsoft® Windows® and Linux operating systems
•
Integrates with other software maintenance, deployment, and operating system tools
•
Automatically checks for hardware, firmware, and operating system dependencies, and installs only
the correct ROM upgrades required by each target server
For more information, see the HP Smart Update Manager User Guide. The guide and the HP Smart
Update Manager utility are available from the ProLiant Firmware Maintenance CD. This CD and others
can be downloaded free of charge from the SmartStart download page on the HP website
(http://www.hp.com/go/support).
Software and configuration utilities 57
Change control and proactive notification
HP offers Change Control and Proactive Notification to notify customers 30 to 60 days in advance of
upcoming hardware and software changes on HP commercial products.
For more information, refer to the HP website (http://www.hp.com/go/pcn).
Care Pack
HP Care Pack Services offer upgraded service levels to extend and expand standard product warranty
with easy-to-buy, easy-to-use support packages that help you make the most of your server investments.
Refer to the Care Pack website (http://www.hp.com/hps/carepack/servers/cp_proliant.html).
Software and configuration utilities 58
Battery replacement
If the server no longer automatically displays the correct date and time, you may need to replace the
battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years.
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temperatures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
• Replace only with the spare designated for this product.
To remove the component:
1.
Power down the server (on page 17).
2.
Unlock the bezel (on page 18).
3.
Remove the access panel (on page 19).
4.
Remove the battery.
To replace the component, reverse the removal procedure.
Run RBSU to configure the system after replacing the battery. Refer to the HP ROM-Based Setup Utility
User Guide for more detailed information.
Battery replacement 59
Troubleshooting
Troubleshooting resources
The HP ProLiant Servers Troubleshooting Guide provides simple procedures for resolving common
problems as well as a comprehensive course of action for fault isolation and identification, error message
interpretation, issue resolution, and software maintenance.
To obtain the guide, refer to any of the following sources and then select the HP ProLiant Servers
Troubleshooting Guide:
•
The server-specific Documentation CD
•
The Business Support Center on the HP website (http://www.hp.com/support). Navigate to the
server technical support page. Under self-help resources, select ProLiant Troubleshooting Guide.
•
The Technical Documentation website (http://www.docs.hp.com). Select Enterprise Servers,
Workstations and Systems Hardware, and then the appropriate server.
Pre-diagnostic steps
WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary
information in the server documentation before removing, replacing, reseating, or modifying
system components
IMPORTANT: This guide provides information for multiple servers. Some information may not
apply to the server you are troubleshooting. Refer to the server documentation for information
on procedures, hardware options, software tools, and operating systems supported by the
server.
1.
Review the important safety information (on page 60).
2.
Gather symptom information (on page 62).
3.
Prepare the server for diagnosis (on page 63).
4.
Use the Start diagnosis flowchart (on page 64) to begin the diagnostic process.
Important safety information
Familiarize yourself with the safety information in the following sections before troubleshooting the server.
Important safety information
Before servicing this product, read the Important Safety Information document provided with the server.
Troubleshooting 60
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no
user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure.
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment,
do not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is
contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
15.0 kg
33.1 lb
WARNING: To reduce the risk of personal injury or damage to the equipment,
observe local occupational health and safety requirements and guidelines for manual
material handling.
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords
to completely disconnect power from the system.
Warnings and cautions
WARNING: Only authorized technicians trained by HP should attempt to repair this
equipment. All troubleshooting and repair procedures are detailed to allow only
subassembly/module-level repair. Because of the complexity of the individual boards and
subassemblies, no one should attempt to make repairs at the component level or to make
modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting 61
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling feet are extended to the floor.
• The full weight of the rack rests on the leveling feet.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against
it. Pay particular attention to the plug, electrical outlet, and the point where the cord
extends from the server.
WARNING: To reduce the risk of personal injury or damage to the equipment:
15.0 kg
33.1 lb
• Observe local occupation health and safety requirements and guidelines for
manual handling.
• Obtain adequate assistance to lift and stabilize the chassis during installation or
removal.
• The server is unstable when not fastened to the rails.
• When mounting the server in a rack, remove the power supplies and any other
removable module to reduce the overall weight of the product.
CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of
clearance at the front and back of the server.
CAUTION: The server is designed to be electrically grounded (earthed). To ensure proper
operation, plug the AC power cord into a properly grounded AC outlet only.
Symptom information
Before troubleshooting a server problem, collect the following information:
•
What events preceded the failure? After which steps does the problem occur?
•
What has been changed since the time the server was working?
•
Did you recently add or remove hardware or software? If so, did you remember to change the
appropriate settings in the server setup utility, if necessary?
•
How long has the server exhibited problem symptoms?
•
If the problem occurs randomly, what is the duration or frequency?
Troubleshooting 62
To answer these questions, the following information may be useful:
•
Run HP Insight Diagnostics (on page 55) and use the survey page to view the current configuration
or to compare it to previous configurations.
•
Refer to your hardware and software records for information.
•
Refer to server LEDs and their statuses.
Prepare the server for diagnosis
1.
Be sure the server is in the proper operating environment with adequate power, air conditioning,
and humidity control. Refer to the server documentation for required environmental conditions.
2.
Record any error messages displayed by the system.
3.
Remove all diskettes and CDs from the media drives.
4.
Power down the server and peripheral devices if you will be diagnosing the server offline. Always
perform an orderly shutdown, if possible. This means you must:
a. Exit any applications.
b. Exit the operating system.
c.
Power down the server (on page 17).
5.
Disconnect any peripheral devices not required for testing (any devices not necessary to power up
the server). Do not disconnect the printer if you want to use it to print error messages.
6.
Collect all tools and utilities, such as a Torx screwdriver, loopback adapters, ESD wrist strap, and
software utilities, necessary to troubleshoot the problem.
o
You must have the appropriate Health Drivers and Management Agents installed on the server.
NOTE: To verify the server configuration, connect to the System Management homepage and
select Version Control Agent. The VCA gives you a list of names and versions of all installed
HP drivers, Management Agents, and utilities, and whether they are up to date.
o
HP recommends you have access to the SmartStart CD for value-added software and drivers
required during the troubleshooting process.
o
HP recommends you have access to the server documentation for server-specific information.
Loose connections
Action:
•
Be sure all power cords are securely connected.
•
Be sure all cables are properly aligned and securely connected for all external and internal
components.
•
Remove and check all data and power cables for damage. Be sure no cables have bent pins or
damaged connectors.
•
If a fixed cable tray is available for the server, be sure the cords and cables connected to the server
are routed correctly through the tray.
•
Be sure each device is properly seated. Avoid bending or flexing circuit boards when reseating
components.
•
If a device has latches, be sure they are completely closed and locked.
Troubleshooting 63
•
Check any interlock or interconnect LEDs that may indicate a component is not connected properly.
•
If problems continue to occur, remove and reinstall each device, checking the connectors and sockets
for bent pins or other damage.
Service notifications
To view the latest service notifications, refer to the HP website (http://www.hp.com/go/bizsupport).
Select the appropriate server model, and then click the Troubleshoot a Problem link on the product page.
Troubleshooting flowcharts
To effectively troubleshoot a problem, HP recommends that you start with the first flowchart in this section,
"Start diagnosis flowchart (on page 64)," and follow the appropriate diagnostic path. If the other
flowcharts do not provide a troubleshooting solution, follow the diagnostic steps in "General diagnosis
flowchart (on page 65)." The General diagnosis flowchart is a generic troubleshooting process to be used
when the problem is not server-specific or is not easily categorized into the other flowcharts.
The available flowcharts include:
•
Start diagnosis flowchart (on page 64)
•
General diagnosis flowchart (on page 65)
•
Server power-on problems flowchart (on page 67)
•
POST problems flowchart (on page 70)
•
OS boot problems flowchart (on page 71)
•
Server fault indications flowchart (on page 73)
Start diagnosis flowchart
Use the following flowchart to start the diagnostic process.
Item
Refer to
1
"General diagnosis flowchart (on page 65)"
2
"Power-on problems flowchart ("Server power-on problems flowchart" on
page 67)"
3
"POST problems flowchart (on page 70)"
4
"OS boot problems flowchart (on page 71)"
5
"Server fault indications flowchart (on page 73)"
Troubleshooting 64
General diagnosis flowchart
The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the
problem, or if the other flowcharts do not fix the problem, use the following flowchart.
Item
Refer to
1
"Symptom information (on page 62)"
2
"Loose connections (on page 63)"
3
"Service notifications (on page 64)"
Troubleshooting 65
Item
Refer to
4
The most recent version of a particular server or option firmware is
available on the following websites:
•
HP Support website (http://www.hp.com/support)
•
HP ROM-BIOS/Firmware Updates website
(http://h18023.www1.hp.com/support/files/server/us/romflash.ht
ml)
5
"General memory problems are occurring" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
6
Server maintenance and service guide, located on the Documentation
CD or the HP website (http://www.hp.com/products/servers/platforms)
7
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
"Server information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
"Operating system information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
8
9
"HP contact information (on page 85)"
Troubleshooting 66
Server power-on problems flowchart
Symptoms:
•
The server does not power on.
•
The system power LED is off or amber.
Troubleshooting 67
•
The external health LED is red or amber.
•
The internal health LED is red or amber.
NOTE: For the location of server LEDs and information on their statuses, refer to the server
documentation.
Possible causes:
•
Improperly seated or faulty power supply
•
Loose or faulty power cord
•
Power source problem
•
Power on circuit problem
•
Improperly seated component or interlock problem
•
Faulty internal component
Item
Refer to
1
"Component identification (on page 6)"
2
"HP Insight Diagnostics (on page 55)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
3
"Loose connections (on page 63)"
4
Server maintenance and service guide, located on the Documentation
CD, or the HP website (http://www.hp.com/products/servers/platforms)
5
"Integrated Management Log (on page 56)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
6
"Power source problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
7
•
"Power supply problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD, or the HP website
(http://www.hp.com/products/servers/platforms)
8
"System open circuits and short circuits" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
Troubleshooting 68
Troubleshooting 69
POST problems flowchart
Symptoms:
•
Server does not complete POST
NOTE: The server has completed POST when the system attempts to access the boot device.
•
Server completes POST with errors
Possible problems:
•
Improperly seated or faulty internal component
•
Faulty KVM device
•
Faulty video device
Item
Refer to
1
"POST error messages and beep codes (on page 75)"
2
"Video problems" in the HP ProLiant Servers Troubleshooting Guide
located on the Documentation CD or on the HP website
(http://www.hp.com/support)
3
KVM or iLO 2 documentation
4
"Loose connections (on page 63)"
5
"Symptom information (on page 62)"
6
Server maintenance and service guide, located on the Documentation
CD or the HP website (http://www.hp.com/products/servers/platforms)
7
"Port 85 and iLO messages" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
8
"General memory problems are occurring" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
9
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
•
"Server information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
"Operating system information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
10
Troubleshooting 70
OS boot problems flowchart
Symptoms:
•
Server does not boot a previously installed operating system
•
Server does not boot SmartStart
Possible causes:
•
Corrupted operating system
•
Hard drive subsystem problem
•
Incorrect boot order setting in RBSU
Troubleshooting 71
Item
Refer to
1
HP ROM-Based Setup Utility User Guide
(http://www.hp.com/servers/smartstart)
2
"POST problems flowchart (on page 70)"
3
•
"Hard drive problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Controller documentation
4
"HP Insight Diagnostics (on page 55)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
5
•
"CD-ROM and DVD drive problems" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
Controller documentation
•
"Loose connections (on page 63)"
6
"General memory problems are occurring" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
7
•
"Operating system problems" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
"HP contact information (on page 85)"
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
8
9
"General diagnosis flowchart (on page 65)"
Troubleshooting 72
Server fault indications flowchart
Symptoms:
•
Server boots, but a fault event is reported by Insight Management Agents (on page 53)
•
Server boots, but the internal health LED, external health LED, or component health LED is red or
amber
Troubleshooting 73
NOTE: For the location of server LEDs and information on their statuses, refer to the server
documentation.
Possible causes:
•
Improperly seated or faulty internal or external component
•
Unsupported component installed
•
Redundancy failure
•
System overtemperature condition
Item
Refer to
1
"Management agents (on page 53)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
2
•
"Integrated Management Log (on page 56)" or in the HP ProLiant
Servers Troubleshooting Guide located on the Documentation CD or
on the HP website (http://www.hp.com/support)
•
"Event list error messages" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
3
"Component identification (on page 6)"
4
System Management Homepage (https://localhost:2381)
5
"Power-on problems flowchart ("Server power-on problems flowchart" on
page 67)"
6
•
"Smart Array SCSI Diagnosis feature" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
•
"HP contact information (on page 85)"
7
"HP Insight Diagnostics (on page 55)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
8
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
Troubleshooting 74
POST error messages and beep codes
For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support).
WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary
information in the server documentation before removing, replacing, reseating, or modifying
system components
Troubleshooting 75
Regulatory compliance notices
Regulatory compliance identification numbers
For the purpose of regulatory compliance certifications and identification, this product has been assigned
a unique regulatory model number. The regulatory model number can be found on the product nameplate
label, along with all required approval markings and information. When requesting compliance
information for this product, always refer to this regulatory model number. The regulatory model number is
not the marketing name or model number of the product.
Federal Communications Commission notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio
Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic
devices, including computers, generate RF energy incidental to their intended function and are, therefore,
covered by these rules. These rules place computers and related peripheral devices into two classes, A
and B, depending upon their intended installation. Class A devices are those that may reasonably be
expected to be installed in a business or commercial environment. Class B devices are those that may
reasonably be expected to be installed in a residential environment (for example, personal computers).
The FCC requires devices in both classes to bear a label indicating the interference potential of the device
as well as additional operating instructions for the user.
FCC rating label
The FCC rating label on the device shows the classification (A or B) of the equipment. Class B devices
have an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on the label. After
you determine the class of the device, refer to the corresponding statement.
Class A equipment
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct
the interference at personal expense.
Class B equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
Regulatory compliance notices
76
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit that is different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio or television technician for help.
Declaration of conformity for products marked with
the FCC logo, United States only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For questions regarding this product, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
•
1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded
or monitored.)
For questions regarding this FCC declaration, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
•
1­281-514-3333
To identify this product, refer to the part, series, or model number found on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the
equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in
order to maintain compliance with FCC Rules and Regulations.
Regulatory compliance notices
77
Canadian notice (Avis Canadien)
Class A equipment
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Class B equipment
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
European Union regulatory notice
This product complies with the following EU Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this
product or product family.
This compliance is indicated by the following conformity marking placed on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g. Bluetooth).
This marking is valid for EU non-harmonized Telecom products.
*Notified body number (used only if applicable—refer to the product label)
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany
Disposal of waste equipment by users in private
households in the European Union
Regulatory compliance notices
78
This symbol on the product or on its packaging indicates that this product must not be disposed
of with your other household waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment. For more information
about where you can drop off your waste equipment for recycling, please contact your local
city office, your household waste disposal service or the shop where you purchased the
product.
Japanese notice
BSMI notice
Regulatory compliance notices
79
Korean notice
Class A equipment
Class B equipment
Laser compliance
This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic
transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in
accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser
radiation.
Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser
Notice No. 50, dated May 27, 2001; and with IEC 60825-1:1993/A2:2001.
WARNING: Use of controls or adjustments or performance of procedures other than those
specified herein or in the laser product's installation guide may result in hazardous radiation
exposure. To reduce the risk of exposure to hazardous radiation:
• Do not try to open the module enclosure. There are no user-serviceable components inside.
• Do not operate controls, make adjustments, or perform procedures to the laser device other
than those specified herein.
• Allow only HP Authorized Service technicians to repair the unit.
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration
implemented regulations for laser products on August 2, 1976. These regulations apply to laser products
manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States.
Battery replacement notice
Regulatory compliance notices
80
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temperatures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Batteries, battery packs, and accumulators should not be disposed of together with the general
household waste. To forward them to recycling or proper disposal, use the public collection system
or return them to HP, an authorized HP Partner, or their agents.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
Taiwan battery recycling notice
The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of
the Waste Disposal Act to indicate the recovery marks on the batteries used in sales, giveaway or
promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
Power cord statement for Japan
Acoustics statement for Germany
(Geräuschemission)
Schalldruckpegel LpA < 70 dB(A)
Zuschauerpositionen (bystander positions), Normaler Betrieb (normal operation)
Nach ISO 7779:1999 (Typprüfung)
Regulatory compliance notices
81
Electrostatic discharge
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the
system or handling parts. A discharge of static electricity from a finger or other conductor may damage
system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the
device.
To prevent electrostatic damage:
•
Avoid hand contact by transporting and storing products in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
•
Place parts on a grounded surface before removing them from their containers.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or assembly.
Grounding methods to prevent electrostatic
discharge
Several methods are used for grounding. Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
•
Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist
straps are flexible straps with a minimum of 1 megohm ±10 percent resistance in the ground cords.
To provide proper ground, wear the strap snug against the skin.
•
Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on both feet
when standing on conductive floors or dissipating floor mats.
•
Use conductive field service tools.
•
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have an authorized reseller
install the part.
For more information on static electricity or assistance with product installation, contact an authorized
reseller.
Electrostatic discharge 82
Specifications
Environmental specifications
Specification
Value
Temperature range*
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-10°C to 60°C (14°F to 140°F)
Maximum wet bulb temperature
28°C (82.4°F)
Relative humidity
(noncondensing)**
Operating
20% to 80%
Non-operating
20% to 90%
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to
3048 m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pressure minimum of 70 KPa.
Server specifications
Specification
Value
Dimension
Height
43.2 cm (17.0 in)
Depth (without bezel)
58.0 cm (22.8 in)
Depth (with bezel)
61.0 cm (24.0 in)
Width
20.0 cm (7.9 in)
Weight (no drives installed)
15.0 kg (33.1 lb)
Input requirement
Rated input voltage
100 VAC to 240 VAC *
Rated input frequency
47 Hz to 63 Hz
Rated input current
8 A (100 V) to 4 A (200 V)
Rated input power
1000 W
BTUs per hour
2730
Power supply output
Rated steady-state power
3.3 V/5 V 110 W
12 V CPU 300 W
Specifications
83
Specification
Value
Maximum peak power
410 W (non-redundant non-hotplug)
430 W (redundant hot-plug)
* 100 to 127 VAC is required for 8 A; 200 to 240 VAC is required for 4 A.
Specifications
84
Technical support
Before you contact HP
Be sure to have the following information available before you call HP:
•
Technical support registration number (if applicable)
•
Product serial number
•
Product model name and number
•
Product identification number
•
Applicable error messages
•
Add-on boards or hardware
•
Third-party hardware or software
•
Operating system type and revision level
HP contact information
For the name of the nearest HP authorized reseller:
•
In the United States, see the HP US service locator webpage (http://www.hp.com/service_locator).
•
In other locations, see the Contact HP worldwide (in English) webpage
(http://welcome.hp.com/country/us/en/wwcontact.html).
For HP technical support:
•
•
In the United States, for contact options see the Contact HP United States webpage
(http://welcome.hp.com/country/us/en/contact_us.html). To contact HP by phone:
o
Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a
week. For continuous quality improvement, calls may be recorded or monitored.
o
If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
information about Care Packs, refer to the HP website (http://www.hp.com).
In other locations, see the Contact HP worldwide (in English) webpage
(http://welcome.hp.com/country/us/en/wwcontact.html).
Customer Self Repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow
for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP
service providers or service partners) identifies that the repair can be accomplished by the use of a CSR
part, HP will ship that part directly to you for replacement. There are two categories of CSR parts:
Technical support 85
•
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
•
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified as
"No" in the Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will help
you over the telephone. HP specifies in the materials shipped with a replacement CSR part whether a
defective part must be returned to HP. In cases where it is required to return the defective part to HP, you
must ship the defective part back to HP within a defined period of time, normally five (5) business days.
The defective part must be returned with the associated documentation in the provided shipping material.
Failure to return the defective part may result in HP billing you for the replacement. With a customer self
repair, HP will pay all shipping and part return costs and determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider. For
the North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client)
afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant
la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut
être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux catégories de pièces
CSR:
•
Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à
HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront
facturés.
•
Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le Catalogue
illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre
situation géographique. Si votre situation géographique le permet et que vous demandez une livraison le
jour même ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une assistance
téléphonique, appelez le Centre d'assistance technique HP. Dans les documents envoyés avec la pièce de
rechange CSR, HP précise s'il est nécessaire de lui retourner la pièce défectueuse. Si c'est le cas, vous
devez le faire dans le délai indiqué, généralement cinq (5) jours ouvrés. La pièce et sa documentation
doivent être retournées dans l'emballage fourni. Si vous ne retournez pas la pièce défectueuse, HP se
réserve le droit de vous facturer les coûts de remplacement. Dans le cas d'une pièce CSR, HP supporte
Technical support 86
l'ensemble des frais d'expédition et de retour, et détermine la société de courses ou le transporteur à
utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus
d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair).
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente
dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di
assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente
al cliente per la sostituzione. Vi sono due categorie di parti CSR:
•
Obbligatorie – Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida
la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
•
Opzionali – Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di
componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare
la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti
sono identificate da un "No" nel Catalogo illustrato dei componenti.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il
giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un
supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica di
un addetto del centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR, HP
specifica se il cliente deve restituire dei componenti. Qualora sia richiesta la resa ad HP del componente
difettoso, lo si deve spedire ad HP entro un determinato periodo di tempo, generalmente cinque (5) giorni
lavorativi. Il componente difettoso deve essere restituito con la documentazione associata nell'imballo di
spedizione fornito. La mancata restituzione del componente può comportare la fatturazione del ricambio
da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e
resa e sceglie il corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair).
Customer Self Repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und
höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP
Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden
kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien
unterteilt:
•
Zwingend – Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn Sie
den Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten
für diesen Service berechnet.
•
Optional – Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für
Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen
Technical support 87
lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog
sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag
geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen
einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support Center
anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSRErsatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden
muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines
vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen. Das defekte Teil muss
mit der zugehörigen Dokumentation in der Verpackung zurückgeschickt werden, die im Lieferumfang
enthalten ist. Wenn Sie das defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung
stellen. Im Falle von Customer Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf
und bestimmt den Kurier-/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner
vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP Website unter
(http://www.hp.com/go/selfrepair).
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer
Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de
realizar sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico, HP (o los
proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el
uso de un componente CSR, HP le enviará dicho componente directamente para que realice su
sustitución. Los componentes CSR se clasifican en dos categorías:
•
Obligatorio: componentes para los que la reparación por parte del usuario es obligatoria. Si
solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los
gastos de desplazamiento y de mano de obra de dicho servicio.
•
Opcional: componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo,
si precisa que HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del
tipo de servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para
que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra
"No" en el catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que lleguen a
su destino al siguiente día laborable. Si la situación geográfica lo permite, se puede solicitar la entrega
en el mismo día o en cuatro horas con un coste adicional. Si precisa asistencia técnica, puede llamar al
Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de
materiales para la sustitución de componentes CSR, HP especificará si los componentes defectuosos
deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP,
deberá hacerlo en el periodo de tiempo especificado, normalmente cinco días laborables. Los
componentes defectuosos deberán devolverse con toda la documentación relacionada y con el embalaje
Technical support 88
de envío. Si no enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En
el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío
y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase
en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica,
visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Customer Self Repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een
minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze
onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP Service Partner)
bij de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSR-onderdeel, verzendt HP
dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee kunt vervangen. Er zijn twee
categorieën CSR-onderdelen:
•
Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening
gebracht.
•
Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te
vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type
garantieservice voor het product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op de
eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten worden
aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een HP Service
Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de documentatie bij het
vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden geretourneerd. Als het defecte
onderdeel aan HP moet worden teruggezonden, moet u het defecte onderdeel binnen een bepaalde
periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het defecte onderdeel moet met de
bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het
defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen.
Bij reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde
onderdeel en kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma
van HP. Informatie over Service Partners vindt u op de HP website
(http://www.hp.nl/services/servicepartners).
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o
reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao
cliente. Existem duas categorias de peças CSR:
Technical support 89
•
Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
•
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas
para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a
cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão
identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil após
o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro horas pode
ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o Centro de suporte
técnico da HP para que um técnico o ajude por telefone. A HP especifica nos materiais fornecidos com a
peça CSR de reposição se a peça com defeito deve ser devolvida à HP. Nos casos em que isso for
necessário, é preciso enviar a peça com defeito à HP dentro do período determinado, normalmente
cinco (5) dias úteis. A peça com defeito deve ser enviada com a documentação correspondente no
material de transporte fornecido. Caso não o faça, a HP poderá cobrar a reposição. Para as peças de
reparo feito pelo cliente, a HP paga todas as despesas de transporte e de devolução da peça e
determina a transportadora/serviço postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato com
o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair).
Technical support 90
Technical support 91
Technical support 92
Acronyms and abbreviations
ACU
Array Configuration Utility
ADU
Array Diagnostics Utility
ASR
Automatic Server Recovery
CMOS
complementary metal-oxide semiconductor
CSR
Customer Self Repair
DDR2
double data rate-2
ESD
electrostatic discharge
EULA
end user license agreement
HP SIM
HP Systems Insight Manager
HPSUM
HP Smart Update Manager
NMI
non-maskable interrupt
PCI
peripheral component interface
Acronyms and abbreviations
93
PCI Express
Peripheral Component Interconnect Express
PCI-X
peripheral component interconnect extended
PDU
power distribution unit
POST
Power-On Self Test
PPM
processor power module
RAID
redundant array of inexpensive (or independent) disks
RBSU
ROM-Based Setup Utility
RDP
Rapid Deployment Pack
SAS
serial attached SCSI
SATA
serial ATA
SCSI
small computer system interface
UID
unit identification
UPS
uninterruptible power system
USB
universal serial bus
Acronyms and abbreviations
94
VCA
Version Control Agent
Acronyms and abbreviations
95
Index
A
access panel 19
ACU (Array Configuration Utility)
additional information 60
air baffle 21
airflow requirements 23
Altiris Deployment Solution 51
Altiris eXpress Deployment Server
Array Configuration Utility (ACU)
ASR (Automatic Server Recovery)
authorized reseller 85
auto-configuration process 47
Automatic Server Recovery (ASR)
Autorun menu 46
48
51
48
52
52
B
Basic Input/Output System (BIOS) 48, 52, 65
batteries, replacing 59, 80
battery 13, 59, 80
battery replacement notice 80
beep codes 75
bezel 18
bezel lock 6, 18
bezel, removing 18
bezel, tower 18
BIOS (Basic Input/Output System) 48, 52, 65
BIOS Serial Console 48
BIOS upgrade 52
blue screen event 13
boot options 48
BSMI notice 79
buttons 6, 7
C
cables 44, 45, 63, 77
cabling 44, 45
Canadian notice 78
Care Pack 22, 58
cautions 61
CD-ROM drive 49
Change Control 58
class A equipment 76
class B equipment 76
component identification 6, 13
components 6, 9, 55
configuration of system 46
configuration tools 46
connection problems 63
connectors 6
contact information 85
contacting HP 85
controller 35, 42, 49
controller board, installing 42
controller installation 42
controller, embedded SATA RAID 49
crash dump analysis 13
creating a disk image 51
CSR (customer self repair) 85
customer self repair (CSR) 85
D
Declaration of Conformity 77
deployment software 51
device numbers 8
diagnosing problems 60, 63
diagnostic tools 46, 51, 52, 55
diagnostics utility 55
DIMM installation guidelines 29
DIMM slot LEDs 13, 14
DIMMs 11, 29, 30
diskette drive 37, 39, 49
diskette drive connectors 11
diskette image creation 51
drive LEDs 8
drivers 57
DVD-ROM drive 6, 32
E
electrical grounding requirements 24
electrostatic discharge 82
Embedded SATA RAID 49, 50
environmental requirements 23
environmental specifications 83
Erase Utility 53
error messages 75
Index 96
European Union notice 78
expansion boards 39, 40
expansion slot covers, removing 39
expansion slots 11, 15
F
fan connectors 11
fan LED 14
fans 16
FCC rating label 76
features 6
Federal Communications Commission (FCC)
notice 76, 77
flowcharts 64, 65, 67, 70, 71, 73
front bezel 18
front panel buttons 7
front panel components 6
front panel LEDs 7
front panel/LED board connector 11
front USB connectors 11
full-height media drive 35
G
general diagnosis flowchart 65
grounding methods 82
grounding requirements 24
H
half-height media drive 32
hard drive bays 6
hard drive blanks 30
hard drive cable connector 11
hard drive LEDs 8
hard drives 30
hard drives, installing 30
hardware options 29
hardware options installation 26, 29
health driver 52
health LEDs 7, 13, 14
help resources 85
HP Insight Diagnostics 55
HP Management Packs 1.1 for MOM 2005,
troubleshooting 60
HP ProLiant Essentials Foundation Pack 53
HP ProLiant Essentials Rapid Deployment Pack 51
HP Smart Update Manager overview 57
HP Systems Insight Manager, overview 53
HP technical support 85
I
identification number 76
iLO (Integrated Lights-Out) 53
iLO 2 (Integrated Lights-Out 2) 53
IML (Integrated Management Log) 56
Important Safety Information document 60
Insight Diagnostics 55
installation services 22
installation, server options 26, 29
installing hardware 29
installing operating system 27
Integrated Lights-Out (iLO) 53
Integrated Lights-Out 2 (iLO 2) 53
Integrated Management Log (IML) 56
internal health LED 14
internal USB connector 11, 54
J
Japanese notice 79
K
keyboard connector 9
Korean notices 80
L
laser compliance 80
laser devices 80
LED, DIMM slot 13, 14
LED, drive activity 7
LED, fan 13, 14
LED, health 7, 14
LED, internal health 7, 14
LED, link/port activity 7, 10
LED, power supply signal 10
LED, processor 13, 14
LED, system power 7, 17
LEDs 6
LEDs, front panel 7
LEDs, hard drive 8
LEDs, NIC 10
LEDs, power supply 10
LEDs, PPM failure 13, 14
LEDs, processor failure 13, 14
LEDs, rear panel 10
LEDs, SAS hard drive 8
LEDs, system board 13
LEDs, troubleshooting 8, 13, 14, 60
loose connections 63
Index 97
M
Management Agents 53
management tools 52
media bay blank 6, 20
memory 30
memory overview 29
memory slot LEDs 13
memory, mirrored 48
modifications, FCC notice 77
mouse connector 9
N
network connector LEDs 10
NIC LEDs 7, 10
NMI switch 11, 13
O
operating systems 57
operations 17
optical device 32
optical drive connector 11
optimum environment 23
Option ROM Configuration for Arrays (ORCA) 51
options installation 26, 29
ORCA (Option ROM Configuration for Arrays) 51
OS boot problems flowchart 71
overtemperature LED 13, 14
P
parallel connector 11, 42
PCI card guide 21
PCI slots 13
PCI-X extender board components 15
PCI-X extender board connector 11
phone numbers 85
POST error messages 75
POST problems flowchart 70
power connectors, external 9
power connectors, internal 11
power cord 61, 81
power cord connector 9
power distribution unit (PDU) 24
Power On/Standby button 6, 17
power requirements 24
power supplies 9
powering down 17
powering up 17, 47
power-on problems flowchart 67
PPM failure LEDs 13, 14
preparation procedures 63
problem diagnosis 60
processor failure LEDs 14
processor power connector 11
ProLiant Support Pack (PSP) 57
PSPs, overview 57
R
rack installation 22
rack resources 22
rack stability 61
rack warnings 61
RBSU (ROM-Based Setup Utility) 47
RBSU configuration 47
rear panel components 9
rear panel connectors 9
rear panel LEDs 10
redundant power supply cable connector 11
registering the server 28
regulatory compliance identification numbers 76
regulatory compliance notices 76, 78, 81
required information 85
requirements, airflow 23
requirements, environmental 23
requirements, power 24
requirements, space 23
requirements, temperature 23
RJ-45 network connector LEDs 10
ROM legacy USB support 54
ROM-Based Setup Utility (RBSU) 47
ROMPaq utility 52
S
safety considerations 60
SAS cabling 45
SAS controller 42
SAS device numbers 8
SAS hard drive cabling 45
SAS hard drive LEDs 8
SATA cabling 45
SATA drives 8
SATA hard drive LEDs 8
SATA optical drive 32
scripted installation 46
serial connector 9, 11
serial number 52
series number 76
server fault indications flowchart 73
Index 98
server features and options 29
server options, installing 26, 29
server setup 26
server specifications 83
server, front panel LEDs 7
server, real panel LEDs 10
server, rear panel components 9
service notifications 64
shipping carton contents 26
site requirements 23
Smart Update Manager 57
SmartStart autorun menu 46
SmartStart Scripting Toolkit 46
SmartStart, overview 46
space requirements 23
specifications, environmental 83
specifications, server 83
start diagnosis flowchart 64
static electricity 82
storage controller 42
support 85
support packs 46
supported operating systems 57
switches 13
symbols on equipment 61
symptom information 62
system battery 11, 59
system board 11
system board battery 80
system board components 11
system board LEDs 13
system configuration settings 46
System Erase Utility 53
system maintenance switch 11, 13
system power connector 11
system power LED 17
system, keeping current 57
Systems Insight Manager 53
troubleshooting resources 60
U
UPS (uninterruptible power supply) 24
USB connectors 6, 9
USB devices 39, 49
USB flash device 33
USB support 54
USB tape drive cable connector 11
utilities 46
utilities, deployment 46, 47, 51
V
ventilation 23
video connector 9
W
warnings 25, 61
website, HP 85
T
Taiwan battery recycling notice 81
tape drives 33, 35
technical support 85
telephone numbers 85
temperature ranges (environmental) 83
temperature requirements 23
tower bezel, removing 18
tower server, setting up 26
troubleshooting 60
troubleshooting flowcharts 64
Index 99