Video Interface for VW Phaeton user manual

ns
tio
lu
So
Video Interface
C
ar
for Volkswagen Phaeton / Bentley
User Manual
www.car-solutions.com
support@car-solutions.com
1. Before installation
tio
13
C
ar
3. Troubleshooting
www.car-solutions.com
3
4
5
6
7
8
9
So
2.1 DIP switch
2.2 Remote controller
2.3 Power cable wiring diagram
lu
2. Setup
ns
1.1 Main specification
1.2 System diagram
1.3 Components
1.4 Exterior
support@car-solutions.com
tio
ns
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 2 x CVBS Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
-. 1 x Analog RGB Input (Car commander original monitor output)
-. 1 x Analog RGB Input (Navigation System output)-OPTION
So
lu
2. Output Spec.
-. 1 x CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x RGB OUTPUT(LCD Operation)
-. 1 x Audio Select OUTPUT (For operating A/V sources – (ex) 12V is come out on V1 port,
when AV1 is chosen.)
C
ar
3. Power Spec.
- Input Power : 8VDC ~ 18VDC
- Consumption Power : 5WATT, Max
4. Switch Input mode
- NAVI/CVBS1,2 Original MUTE Function : Possible to mute each input by operating Dip S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view camera
mode (Impossible to switch to rear mode with Toggle S/W or the Remote control)
www.car-solutions.com
support@car-solutions.com
tio
Navigation Input
(Analog RGB)
So
VIDEO
CIRCUIT
VIDEO MUX
C
ar
POWER
CIRCUIT
Power Input
(+8VDC~+18VDC)
www.car-solutions.com
CAR Installation
OEM LCD
lu
CVBS 2
CAR SCREEN INPUT
(CAR MAIN BOARD)
DISPLAY
MCU
CVBS 1
CVBS
(Rear Camera)
Switch for source toggle & REAR SENSE
ns
Remote Control
CVBS
OUT
HEADREST
MONITOR
DIP S/W
support@car-solutions.com
RGB NAVI cable * 1ea
GROUND cable * 1ea
So
lu
tio
SEL cable * 1ea
ns
1.3 Components
C
ar
REMOTE CONTROL * 1ea
POWER cable * 1ea
www.car-solutions.com
MODE cable * 1ea
Sub-board * 1ea
FFC cable * 1ea
ORANGE cable * 1ea
IR cable * 1ea
support@car-solutions.com
1.4 Exterior
⑬
⑫
⑩
⑪
⑨
⑧
Dimension
⑫
⑪
⑩
⑨
⑧
C
ar
So
lu
tio
⑬
ns
Horizontal length 129mm
Vertical length 75mm
Height 21mm
①
②
③
④
⑤
① POWER
② MODE
③ IR
④ V1
⑤ V2
⑥ R/V
⑦ V-OUT
⑧ NAVI (IN)
⑨ OEM (IN)
⑩ RGB OUT
⑥
⑦
⑪ DIP S/W
⑫ AUDIO-SEL
⑬ LED
①
www.car-solutions.com
②
③
④
⑤
⑥
⑦
support@car-solutions.com
RGB INPUT skip
ON : Skipping RGB Mode
OFF : RGB Display
CVBS1 MUTE
ON : Skipping CVBS1
OFF : CVBS1 Display
3
CVBS2 MUTE
ON : Skipping CVBS2
OFF : CVBS2 Display
4
CAN
5
OEM MUTE
ON : Skipping OEM
OFF : OEM Display
6
INTERLACE
ON : Non-Interlace
OFF : Interlace
7
REAR MODE
8
-. Use Input Mode : CVBS1, Navigation (RGB), Main
-. Rear Camera : When to be installed on CVBS 4
So
ON : When install to the Cayenne
OFF : When install to all of the car
C
ar
2
[W211]
ns
1
※DIP S/W Use Example
DIP S/W selection
tio
Function
SYNC ON GREEN
ON : External Rear Camera
OFF : OEM Rear Camera
ON : Sync On Green (RGSB)
OFF : Sync On Green Off
www.car-solutions.com
▷
▷
▷
▷
▷
▷
▷
▷
lu
#PIN
DIP S/W : 1 OFF
DIP S/W : 2 OFF
DIP S/W : 3 ON
DIP S/W : 4 OFF (All of the Car except Cayenne)
DIP S/W : 5 OFF
DIP S/W : 6 OFF
DIP S/W : 7 ON (enable CVBS4)
DIP S/W : 8 OFF
* Caution
- If the displayed screen vibrates, please try to operate
Dip S/W No. 6 after turning power off.
support@car-solutions.com
OSD implementation
Making a selection
▲
Move upward
▼
Move downward
C
ar
▶
So
OK
◀
tio
MENU
Not for use
lu
POWER & PIP
Function
ns
Key
Move leftward, press 2 seconds long-Factory
mode implementation
Move rightward, press 2 seconds long-Factory
Mode implementation-Factory mode Reset
SIZE : 85 * 40 * 8 (mm)
www.car-solutions.com
support@car-solutions.com
2.3 Power cable wiring diagram
⑤
④
③
②
①
ns
⑥
tio
FILTER
& FUSE BOX
So
lu
① GND (black)
② I-Drive (orange)
③ FMTX antenna
④ N.C
⑤ ACC(red)
⑥ REAR(gray)
C
ar
Gray
Blue
Orange
Red
Blue
Orange
Black
990mm
Red
Black
Grey
990mm
www.car-solutions.com
FMTX
I - DRV
GND
ACC
LAMP - RV
support@car-solutions.com
3. Troubleshooting
ns
Q. I can not switch A/V sources.
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
tio
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.
(Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
So
Q. Rear camera image does NOT appear.
A. Set DIP switch #7 in “ON”
lu
Q. Displayed image color is not proper. (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform the manufacturer.)
C
ar
Q. Unwanted A/V mode is displayed. (A/V source switching order : OEM->RGB->AV1->AV2->AV3)
A. Check DIP Switch Setting.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform the manufacturer.
Q. Screen only displays white like left picture.
A. Check LCD out cable is connected well, if this status keeps, inform the manufacturer.
www.car-solutions.com
support@car-solutions.com