- Home
- Home security & automation
- Security access control systems
- Radio Shack
- Wireless Key-Lock Door/Window Alarm 49-118
- User manual
Radio Shack 49-118 User manual
Add to my manuals
Radio Shack Wireless Key-Lock Door/Window Alarm 49-118 is a versatile security device that can be used to protect any door or window from unauthorized entry. The alarm can be activated to sound in two ways: with no delay, or with a 15-second delay setting that allows you to enter your home without triggering the alarm. When the magnet is separated from the alarm, the LED indicator lights up green and the alarm sounds for 90 seconds or until the key is turned to the OFF position. If the alarm is triggered while you are away, the LED indicator will alternately flash green and red after the alarm has finished the 90 seconds cycle.
advertisement
LED
Alarm
Adhesive Strip (3)
Keys
Choosing a Location
1.
Align the triangle on the magnet with the engraved line on the left or right side of the alarm.
2.
Place the magnet edge no more than
5 /
16
- inch (8 mm) from the alarm.
3.
Mount the alarm to a door or window and the magnet to the door or window frame using the supplied adhesive strips or screws.
49-118
W i r e l e s s · K e y - L o c k
D O O R / W I N D O W A L A R M
Magnet
Anchor (4)
Screw (4)
Using Your Alarm
Instant Activation
1.
Slide INSTANT/DELAY switch to INSTANT.
2.
Insert key and rotate to ON.
3.
If you move the magnet away from the alarm, it sounds for about 90 seconds. Then, the alarm turns off and the LED flashes green. Turn the key to OFF if you want to silence the alarm immediately.
Delay Activation
1.
Slide INSTANT/DELAY switch to DELAY.
2.
Insert key and rotate to ON. The LED lights green and you have 15 seconds to leave and close the door. After 15 seconds, the alarm arms and the LED turns off.
Deactivation
1.
When you return home and open the door, the LED lights red and you have 10 - 15 seconds to turn off the alarm.
2.
Turn the key to OFF to disarm. If you do not disarm it, the alarm sounds for 90 seconds.
3.
If the alarm was triggered while you were away, the LED alternately flashes green and red after the alarm has sounded for 90 seconds.
Mounting Your Alarm Using Screws
Setting Up Your Alarm
Mounting the Magnet
1.
Use the supplied drilling template to mark the mounting screw location.
2.
Drill two 1 /
16
- inch (2 mm) holes.
3.
Insert the top screw, leaving about 1 /
8
- inch
(3 mm) to engage the keyhole on the alarm.
4.
Install the alarm over the top screw.
5.
Slide off the battery cover.
6.
Insert the lower screw through the hole inside the battery compartment.
1.
Use a small, flat bladed screwdriver to remove the mounting plate from the magnet.
2.
Use the supplied screws or adhesive strips to secure the mounting plate to the selected surface. Do not use both strip and screws.
3.
Connect magnet to mounting plate.
Magnet (Rear View)
Mounting
Plate
Battery
Cover Drilling
Template
Apply to frame
Thank you for purchasing your Door/Window
Alarm from RadioShack. Please read this user’s guide before installing, setting up and using your new door/window alarm.
www.radioshack.com
What’s Included
Alarm
Key (2)
Screw (4)
Drilling Template
Magnet
Adhesive Strip (3)
Anchor (4)
User’s Guide
Actual product may vary from the images found in this document.
Battery Notes:
• Dispose of old batteries promptly and properly. Do not burn or bury them.
• Use only fresh batteries of the required size and recommended type.
• Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities.
• If you do not plan to use the alarm for a month or more, remove the batteries.
Batteries can leak chemicals that can destroy electronic parts.
Installing Batteries
1.
Remove the screw on the bottom of your alarm and lift the battery compartment cover.
2.
Insert two AAA batteries (not supplied), as indicated by the polarity symbols (+ and -) marked inside.
3.
Replace the cover.
4.
Replace the batteries if the alarm sound weakens or the LED flashes red. If the alarm does not work after you replace the batteries, remove and reinstall them.
5 /
16
“ max
©2007. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
09A07
49-118
Printed in China
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement