CITROEN C5 Specifications

CITROËN C5
Owner’s handbook
A partnership of expertise
For 39 years, the research teams of
Citroën and Total have combined their
know-how to offer you the best engine/
lubricant combination available.
Cutting edge technology for your benefit.
With Total, you can be sure to have chosen the benchmark
oil that best guarantees your Citroën’s performance and lifeexpectancy.
A partnership for the environment
Total oils support Citroën’s advances in fuel
economy, and C02 and harmful emission reductions.
The development of new generation oils specially
adapted for Particle Filters, like TOTAL ACTIVA/
QUARTZ INEO ECS can reduce C02 emissions
by a tonne* and save a tank of fuel each year**.
*Official C02 emissions reduction of 4g per km (approx. 6g per mile). Corresponds to a reduction
in C02 emissions of 1 tonne throughout the life of the vehicle, on a private diesel vehicle with an
average life expectancy estimated at 250 000 km (approx. 160 000 miles). Source: TOTAL. **Or
30L, average quantity of fuel required to fill a tank at a petrol station. Result obtained using TOTAL
ACTIVA/QUARTZ INEO ECS oil instead of a traditional 15W-40 oil, on a CITROËN C4 1.6HDi,
whose average fuel consumption is 58.9 mpg (4.8L/100km), travelling 18 000km (approx. 12 000
miles) per year. Source: TOTAL. .
A partnership of success
Competitive successes in the national rallies of the World
Rally Championship bear testament to the performance and
efficiency of the Citroën – Total partnership.
prefers
CAFEINE - TOTAL LUBRIFIANTS, Le Diamant B, 16 rue de la République, 92922 PARIS LA DEFENSE - 552 006 454 RCS Nanterre - www.lubrifiants.total.com
Citroën and Total
This handbook is compiled on the basis of all the equipment (whether standard or optional) that is
available, and of the technical specifications that were known at the time of going to print.
The level of equipment on your vehicle depends on the model,
the options chosen and the country where the vehicle is marketed.
Some of the equipment mentioned in this handbook may only become available at a later date.
Descriptions and illustrations are given without obligation.
AUTOMOBILES CITROËN reserves the right to modify its models and their
equipment without necessarily being bound to update the present handbook.
The trained, professional staff of the CITROËN network are at
your disposal to answer any questions you may have.
We wish you safe and enjoyable motoring in your new CITROËN.
This handbook is an integral part of the vehicle.
Keep it where it can be easily consulted.
Do not forget to pass it on to the new owner,
should you sell your vehicle.
X7-GB-3008
Edition 03-2008
We thank you and congratulate you for choosing to drive a new CITROËN. Please read this
handbook carefully before taking to the road. It contains essential information about driving
your vehicle and operating its equipment, as well as other important advice to be rigorously
followed. The types of equipment your vehicle possesses will be dependent on its version,
on the options you have chosen as well as on the country where it was marketed. The
handbook also contains all you need to know about the servicing and routine maintenance
of your vehicle, thus assuring both your safety and the reliability of your new CITROËN, a
thorough knowledge of which will enable you to enjoy driving to the full.
Depending on the version of your vehicle and the options it possesses, as well as on its date of marketing,
some of the functions or types of equipment described in this handbook may not be present on the
vehicle.
C ont e nt s
4-21
I
IN BRIEF
Exterior.................................................. 4
Opening..............................................5-6
Interior................................................... 7
Dashboard...................................... 8➟10
Getting started................................11-12
Visibility............................................... 13
Ventilation............................................ 14
Monitoring...................................... 15-16
Passenger safety.................................17
Driving.......................................... 18➟21
22-91
II
Driving
Remote control............................... 22-23
Keys..................................................... 24
Anti-intrusion alarm........................25-26
Steering lock Ignition - Starter................................ 27
Starting................................................ 28
Instrument panel.....................29➟33-41
Warning lamps. ............................. 29➟33
Diesel particulate filter system............ 33
Instrument panel.......................... 34➟41
Trip computer.................................34-35
Navigation........................................... 35
Checks / Oil level................................. 36
Maintenance indicator.................... 37-38
Main Menu........................................... 39
Vehicle parameters............................. 40
Fixed centred controls
steering wheel.............................. 42-43
Signalling...................................... 44➟46
Bend lighting....................................... 47
Xenon dual function directional
headlamps - Angled lighting............. 48
Wipers............................................49-50
Windows...............................................51
Steering column adjustment Seat belt height adjustment....................52
Front seats................................... 53➟55
Memorisation of
driver's adjustments.......................... 56
Rear view mirrors........................... 57-58
Multifunction display..................... 59➟62
Manual gearbox.................................. 63
Automatic gearbox....................... 64➟67
Cruise control.................................68-69
Speed limiter.................................. 70-71
Tyre deflation detection.................. 72-73
Brakes..................................................74
Electric parking brake.................. 75➟81
Hill start assist..................................... 82
Manual parking brake......................... 83
Electronic stability programme........... 84
“Hydractive III+” suspension..........85-86
Lane Departure Warning System....... 87
Parking assistance.........................88-89
Parking space sensor....................90-91
C ont e nt s
92-125
III
126-143
IV
VI
161-179
Comfort
Radio
Practical advice
Access............................................92-94
Automatic air conditioning.......... 95➟102
General........................................ 95➟96
Audio/telematics system................... 126
RDS audio compact disc system...... 127
Button controls.................................. 128
Controls at the steering wheel.......... 129
General functions Audio adjustments.......................... 130
Radio source...............................131-132
RDS system............................... 133-134
CD/CD MP3 source................... 135-136
CD changer source............................137
Bluetooth®.................................138➟140
HiFi system.........................................141
Frequently-asked questions........142-143
Fuel.................................................... 161
Changing bulbs.........................162➟171
Safety recommendations...................172
Puncture kit........................................173
Changing a wheel..................... 174➟176
Towing – Lifting................................. 177
Very cold protection...........................178
Snow guard........................................179
Monozone..................................... 97➟99
Dual-zone................................. 100➟102
Programmable heating............... 103-105
Rear seats.................................. 106-107
Airbags.............................................. 108
Child safety....................................... 109
Child restraints.......................... 110➟113
Interior lighting........................... 114➟116
Interior comfort.......................... 117➟119
Boot (saloon)..................................... 120
Boot (Tourer)......................................121
Luggage cover blind (Tourer)............ 122
Cargo net (Tourer)............................. 123
Sunroof (saloon)................................ 124
Panoramic roof (Tourer).................... 125
144-160
V
Maintenance
Bonnet release.................................. 144
Petrol engines...........................145➟146
Diesel engines........................... 147➟148
Levels......................................... 149-150
Diesel injection equipment..........151-152
Capacities......................................... 153
12V battery................................. 154-155
Fuses........................................ 156➟160
VII
180-188
Technical specifications
General...................................... 180-181
Fuel consumption....................... 182-183
Dimensions (saloon)................... 184-185
Dimensions (Tourer)................... 186-187
Vehicle identification......................... 188
Alphabetical index................ 189
User Precautions.............. I -xxIV
Ext e rior
I
The Xenon dual-function directional
headlamps
This function automatically provides you
with extra visibility on bends. This lighting is
linked with the angular lighting which maximises the area lit at intersections and when
parking.
This provides you with improved brightness in the
passenger compartment.
Glass sun roof (saloon)
This also provides you with improved ventilation in the
passenger compartment.
124-125
IN BRIEF
48
Glass panoramic roof (Tourer)
Lane Departure Warning
System
This driving assistance device
warns you when you unwittingly
cross a lane marking.
87
Parking assistance
(visual + sound)
Tyre deflation detection
This function warns you, whilst
manoeuvring,
by
detecting
obstacles located in front of and
behind the vehicle.
88
This function monitors the pressure of each tyre and warns you
of tyres that are punctured or
deflated.
72
O p e ning
Remote control key
C
Opening the boot
Fuel tank
I
A
B
E
A.Key release / storage.
B.Locking of the vehicle.
C.Unlocking of the vehicle.
D.Guide-me-home lighting.
To open the fuel flap, press on the
top left part of it, then pull from the
edge.
E
Press upwards on the lever E.
The boot automatically locks when
the vehicle is moving at a speed
of over 10 km/h (6 mph), even if
automatic central locking is deactivated. It is unlocked when a door is
opened or when the central locking
button is pressed (speed lower than
10 km/h (6mph)).
22
93
Locking filler cap
Turn the key a quarter turn to lock
and unlock the filler cap.
When refuelling, place the cap on
hook F.
IN BRIEF
F
D
Tank capacity:
approximately 71 litres
161
O p e ning
Bonnet release
Spare wheel
Access to the spare wheel
To access the spare wheel:
1. Lift up the boot floor using the
strap (saloon) or the retractable
hook (Tourer).
2. Fold back the boot carpet
(saloon).
3. Attach the hook to the upper
section of the boot.
4. To remove the spare wheel,
detach the strap then push the
wheel forwards, before lifting it
out.
I
IN BRIEF
A
This operation should only be
performed while the vehicle is
stationary.
Open the door.
To unlock, pull release lever A.
Saloon
Puncture kit
B
Tourer
Lift up lever B, then raise the bonnet.
144
Note: The tools are to be found
in a protective holder inside the
spare wheel.
174
The puncture repair kit is a complete system including a compressor and a setting product.
173
Interior
Dual-zone automatic air
conditioning
Parking space sensor
The “Parking Space Sensor” function assists you in finding a parking
space.
This function enables you to adjust the comfort levels of the driver and the front passenger independently. It is also automatically
regulated depending on the external climatic
conditions.
100
I
IN BRIEF
90
Audio and communication
systems
This equipment benefits from the latest technology: MP3 compatible RD4
radio, Bluetooth® hands-free kit,
NaviDrive (See NaviDrive instructions).
126
Electric parking brake
The electric parking brake combines automatic engagement when
the engine is switched off, and automatic release when the vehicle is
set in motion (automatic function activated by default).
Note: Manual locking/unlocking is possible.
75
D a s hboard
1 Electric windows / rear view mirrors / Child
safety controls
2 Memorisation of driver’s seat, rear view mirrors
and air conditioning settings
I
3 Controls at the steering wheel:
- Speed limiter
- Cruise control
8
9
10
5 Audio/telematic controls under steering wheel
2
6 Driver's airbag
7 Navigation controls
6
11
IN BRIEF
4 Horn
7
4
19
20
16
3
15
1
5
8 Driver's air vent
9 Instrument panel
10Driver's air vent
11 Lighting control
12Windscreen wiper / Screen wash controls
13Ignition switch
14 Controls:
- Locking/unlocking of doors and boot
- Lane Departure Warning System
14
15Steering column adjustment
16Knees airbag
17Oddments tray
18
18Checks / Anti-intrusion alarm / Parking space
sensor controls
19Lighting / Direction indicators / Foglamp / Voice
recognition controls
12
13
20Manual headlamp height adjustment
17
D a s hboard
21Sunlight sensor
21
22Soft diffusion air conditioning adjustment knob
23Passenger's airbag
24
22
23
I
24Side window demister
26Bonnet release
25Passenger's air vents
27Hazard lamps button
28 Key switch:
- Passenger’s airbag activation/deactivation
41
27
29Glovebox:
- Vehicle document storage
- Audio-video sockets
- Fusebox access flap
40
29
26
28
30ESP / Parking assistance controls
39
30
31Automatic gearbox SPORT/SNOW mode
controls
38
32Electric parking brake
36
37
35
33Armrest with cup-holder
34Suspension controls:
- Ground clearance adjustment
- Sport mode
IN BRIEF
25
35Ashtray with lighter
34
31
36Gear lever
37Storage
38Radio mono CD or NaviDrive
32
33
39Air conditioning controls
40Storage
41Multifunction display
D a s hboard
IN BRIEF
I
Instrument panel menu
Multifunction
display menu
Activation of voice
recognition or reminder of
navigation guidance
MODE: selection of the type
of information displayed on
multifunction screen.
Cruise control
and Speed limiter
Audio
Telephone
10
The “SET +, PAUSE, VOL+, MUTE”
buttons are located so that you can
use them without needing to take
your eyes off the road.
42
G e tting s tart e d
Front seats
Seat belt height adjustment
Manual adjustments
Electrical adjustments
I
J
J
E
A
B
D
A.Adjustment
angle.
C
of
the
H
G
F.Seat height and slide adjustments.
G.Adjustment of the backrest
angle.
H.Adjustment of top of backrest.
I. Adjustment of 2 axis lumbar
support.
J.Massage function.
The correct positioning of the belt
strap is through the middle of the
shoulder. See “Seat belts”.
To adjust the seat belt for height,
compress the control and slide it
in the desired direction.
K.Heated seat control.
backrest
B.Adjustment of the seat height
and angle.
Memorisation
The Memorisation function allows
you to programme the driver’s
seat, rear view mirrors and air
conditioning settings.
C.Heated seat control.
D.Longitudinal adjustment of seat.
E.Adjustment of the backrest lumbar support.
53
F
IN BRIEF
I
K
54
56
11
G e tting s tart e d
I
Electric exterior rear view
mirrors
a
Automatic electrochrome
rear view mirror
Steering column adjustment
b
c
IN BRIEF
2
12
3
1
4
1. Selection of rear view
mirror:
a - Left hand side.
b - Right hand side.
c - Foldback / Deployment.
2. Directional control for
mirror selected
58
This automatically and progressively adapts to day-time or nighttime use.
Operation
Switch on the ignition and press
button 4.
• Warning lamp 3 on: automatic
mode.
• Warning lamp 3 off: automatic
mode stopped. The mirror
remains in its lightest definition.
57
A
With the vehicle at rest, unlock
the steering wheel by pushing control A forwards.
Adjust the height and the reach
of the steering wheel, then lock
the position by pulling the lever
upwards.
52
V i s ibilit y
Lighting
Front wipers
Rear wipers (Tourer)
I
C
B
Ring A
Lamps off.
Automatic lighting of headlamps.
Sidelamps.
Dipped beams/main
beams.
Pull the control stalk towards you
to change between dipped beam
and main beam.
Ring B
Front foglamps on.
Front foglamps and
rear foglamps on.
45-46
Control positions
2.Rapid wipe.
1.Normal wipe.
I. Intermittent wipe.
0.Off.
One press downwards:
• AUTO: Automatic wipe activated.
• Single wipe.
Rotate control C to the desired
position.
Off
Intermittent wipe
IN BRIEF
A
Screen wash
Screen wash
Pull the screen wipe control stalk
towards you.
Note: If the ignition has been
switched off for around 1 minute,
it is necessary to re-activate
automatic wiping.
49
50
13
V e ntilation
Automatic air conditioning
Adjustment
of temperature on
driver's side
I
IN BRIEF
Front demisting deicing
Adjusting the air flow
Adjustment of air distribution
on driver's side
Activation/deactivation
of air conditioning
Adjustment of
temperature on
passenger's side
Passenger's side
automatic operation
Driver's side automatic
operation
Adjustment of air
distribution on
passenger's side
Rear and external rear view
mirrors demisting - deicing
Air recirculation Entry of air from outside
Note: It is recommended to use automatic mode by pressing on the “AUTO” button.
14
97
M onitoring
Instrument panel
I
D
H
C
I
E
1
F
J
G
G. Trip mileage recorder reset button.
H. Rev counter.
I. Engine oil temperature.
J. Display of automatic gearbox information.
A. Fuel gauge and low fuel warning lamp.
B. Cruise control/speed limiter information.
C. Coolant temperature.
D. Speed indicator.
E. Instrument panel.
F. Mileage recorder.
29
IN BRIEF
B
A
Hazard warning lamps
The hazard lamps can
also be used with the ignition switched off.
44
Note:
• When the ignition is switched on, the orange
and red warning lamps light up.
• When the engine is running, these warning
lamps should go out.
• If any warning lamps remain lit, refer to the
relevant page.
15
M onitoring
Tyre deflation detection
Log of alerts
Economy mode
I
IN BRIEF
A
16
The tyre deflation detection system
is a driving aid which informs you
of the condition of your tyres.
It does not replace either vigilance
or responsibility on the part of the
driver.
72
This function allows you to display
the log of alerts.
Press on button A. The following
messages appear consecutively
on the instrument panel screen:
• Tyre pressure check.
• Maintenance indicator reminder.
• Display of message alerts.
• Oil level check.
36
When the engine is stopped, some
functions (audio system, screen
wipe, electric windows, sunroof,
electric seats, telephone, video,
interior lighting etc.) are only electrically supplied for a maximum
period of 30 minutes, to avoid discharging the battery.
Once this period is over, a message is displayed on the instrument panel screen and the active
functions are placed on standby.
These functions will be automatcially reactivated when the vehicle
is restarted.
27
PA SSE N G E R S A F E T Y
Seat belts and front
passenger's airbag
C D
E
Front passenger's airbag
deactivation
Child safety
I
H
I
B
F
The seat belt fastened/unfastened
status for each seat category is
indicated by the lighting or flashing of the warning lamps linked to
each position:
A. Non-fastened / unfastened
front and/or rear seat belts
warning lamp.
B. Front left-hand seat belt warning lamp.
C. Front right-hand seat belt
warning lamp.
D. Rear right-hand seat belt
warning lamp.
E. Central rear seat belt warning
lamp.
F. Rear left-hand seat belt warning lamp.
G.Front passenger's airbag
deactivation warning lamp.
H. Front passenger's airbag activation warning lamp.
32
J
G
In order to be able to use a rearfacing child seat in the front passenger's seat position, it is imperative to deactivate the passenger's
airbag.
For that:
• With the ignition switched off,
insert the key into the switch I.
• Turn the key to the “OFF” position, the passenger's airbag is
deactivated.
The front passenger's airbag deactivation warning lamp G lights up
when the ignition is switched on.
108
This deactivates the controls in the
rear of the vehicle, both for the rear
windows and for opening the rear
doors from the inside. The electric
child safety device is activated by
pressing on button J.
The activation of the function is
indicated by a message on the
instrument panel screen and the
light on button J.
51
IN BRIEF
A
17
D riving
Electric parking brake
Hill start assist
I
B
A
Manual operation
IN BRIEF
Automatic operation
The electronic parking brake
releases automatically and progressively when you press the
accelerator. With the vehicle stationary, the parking brake is automatically applied when the engine
is switched off.
The MANUAL application/release
of the parking brake is possible
permanently by pulling/pushing
control B.
Before leaving the
vehicle, check that
warning lamp A (!)
(red) on the instrument panel is permanently lit and
that warning lamp P (red) on control B is lit.
Before leaving the
vehicle, check that
warning lamp A (!)
(red) on the instrument panel is permanently lit and
that warning lamp P (red) on control B is lit.
Never leave a child alone
inside the vehicle with
the ignition on, as they
could release the parking
brake.
18
With the engine running,
if you leave the vehicle,
manually apply the parking brake.
75
To aid starting on a gradient, your
vehicle is equipped with a system
which keeps it immobilised for a
short time (about 2 seconds), the
approximate time it takes to move
your foot from the brake pedal to
the accelerator pedal.
This function is only active when:
• The vehicle is completely stationary, with your foot on the
brake pedal.
• In particular conditions on a
slope.
• With the driver's door closed.
Do not leave the vehicle
while it is being held in the
temporary immobilisation
hill start assist phase.
82
D riving
Speed limiter
Instrument panel display
Cruise control
This system allows you to choose
a maximum speed that you do not
wish to exceed.
Selection of “LIMIT”: Activation of speed limiter
mode.
This system allows you to maintain a constant vehicle speed programmed by the driver.
“SET +”: Increase of the
maximum speed.
“SET”: Memorisation
of the speed (system
paused).
“SET -”: Reduction of the
maximum speed.
Suspension or resumption
of mode.
Deactivation.
The chosen speed is memorised.
Note: The chosen speed must be
higher than 30 km/h (20 mph).
70
Selection
of “CRUISE”:
Activation of cruise control
mode.
“SET +”: Increase of the
memorised speed (system
ON).
“SET -”: Reduction of the
memorised speed (system
ON).
The speed limiter or cruise control
mode is displayed on the instrument panel when selected.
Speed limiter
IN BRIEF
I
Cruise control
Suspension or resumption of
mode.
Deactivation.
68
Cruise control is active on the
higher gears of the gearbox. The
chosen speed must be higher
than 40 km/h (25 mph).
19
D riving
I
Direction indicators “Motorway” function
Automatic gearbox
IN BRIEF
A
B
Move the stalk briefly upwards or
downwards, without going beyond
the resistance point; the direction
indicators will flash 3 times.
Positions
P: Parking.
R: Reverse gear.
N: Neutral.
D: Automatic mode.
M: Sequential mode.
20
44
The automatic gearbox offers you:
- Operation in auto-active mode,
with automatic adaptation to your
style of driving as well as to the
road profile (Position D).
- Operation in sequential mode,
with manual gear changing (Position M).
- Operation in automatic SPORT
mode (Position D) and press
button A.
- Operation in automatic SNOW
mode (Position D) and press
button B.
For safety:
The gear lever can
only be disengaged
from position P if
you are pressing the
brake pedal.
When a door is opened, an
audible signal sounds if the
gear selector is not in position P.
Before leaving the vehicle,
make absolutely certain that
position P is selected.
64
D riving
Parking space sensor
Parking assistance (visual
and sound)
Lane Departure Warning
System
I
B
You can select the “Parking Space
Sensor” by pressing button A,
which flashes when next to the
space to be measured, with a speed
lower than 20 km/h (12 mph) and
at a distance of less than 1.5 m
from the space.
The fixed lighting of the warning
lamp indicates that this function is
selected.
C
You can activate/deactivate the
parking assistance by pressing
button B. When the parking assistance is inactive, the warning lamp
on button B is lit up.
This device is designed for use on
motorways and dual carriageways,
and operates only at speeds above
80 km/h (50 mph).
A press on button C activates the
function, the warning lamp on the
button lights up.
IN BRIEF
A
Note: The system does not
alert you if one of your direction indicators is operating and
for approx. 20 seconds after the
direction indicator has stopped.
90
88
87
21
R e mot e control
A
B
C
D
II
E
Note:
• The simultaneous use of other
high
frequency
equipment
(mobile telephones, domestic
alarms, etc.) may momentarily hinder the operation of the
remote control.
• If there is a permanent fault, the
remote control has to be reinitialised. See “Changing remote
control batteries”.
22
Central unlocking
A press on button A unlocks your
vehicle.
This is confirmed by rapid flashing
of the direction indicators and lighting of the interior lamp (provided
this function is active). This also
deploys the exterior rear view mirrors.
Central locking / Closing
of windows and sunroof /
Deadlocking
• A short press on button C
locks your vehicle.
• A long press on button C locks
your vehicle and closes the windows and the sun roof.
• 2 successive presses on button C will deadlock the vehicle.
It is then impossible to open the
doors, either from the inside or
from the outside.
This operation is confirmed by the
direction indicators illuminating for
approx. 2 seconds and by the interior lamp switching off. This also
folds the exterior rear view mirrors.
If any of the doors, or the boot, is
open or not properly closed, the
central locking does not operate.
With the vehicle stationary and the
engine switched off, locking is signalled by the flashing of the interior
locking control warning lamp.
Guide-me-home lighting
A press on button B activates the guide-me-home
lighting (lighting of the
sidelamps, dipped beams,
registration plate lights for
around 1 minute).
A second press prior to the end of
this timing cancels the guide-mehome lighting.
If closing the windows and sun roof using the remote control,
the user must make sure that no person is preventing the
windows and/or sun roof from closing properly.
It is dangerous to operate the deadlocking when a person is
inside the vehicle as unlocking is impossible from the inside
without the remote control.
R e mot e control
Electric boot opening
Pressing button E opens
the boot.
Locating of the vehicle
To locate the vehicle in a carpark,
press button C. Locating of the
vehicle is confirmed by:
• The flashing of the direction
indicators for a few seconds.
• The interior lighting coming on.
The vehicle remains locked.
Folding and ejecting the key
Button D is for folding and ejecting the key from its housing in the
remote control.
If you do not press on button D,
you could damage the key mechanism.
Changing the remote
control battery
Unclip the cover to gain access to
the battery.
Battery: CR 0523 de 3 V.
Re-initialisation of the
remote control
After a change of battery, it is necessary to re-initialise the remote
control. To do that, switch on the
ignition and immediately press button C of your remote control until
you achieve the desired result.
This may take some ten seconds.
II
Note: Make a careful note of the
numbers for the keys and for the
remote control on the ASSISTANCE
card. Keep this in a safe place.
Do not throw away used batteries. Return them to a CITROËN
dealer or take them to an authorised recycling facility (camera
shops, etc).
Except when reinitialising, the remote control cannot function while the key is in the ignition, even
when switched off.
Warning: by inadvertently actioning the remote control, when for example it is in your pocket, you
can unlock the vehicle without your realising it.
However, if none of the doors is opened within thirty seconds following an unlocking, the doors will
automatically relock.
Warning: there is a risk of damage if the replacement battery is not the correct one.
Only use batteries that are identical or equivalent to those approved by CITROËN.
23
Keys
Central locking using the
key
Briefly turn the key in the door lock.
The vehicle is locked.
II
Deadlocking: Central
locking using the key
Electronic immobiliser key
The key operates all the vehicle’s
locks as well as the ignition.
The key can be used to deactivate
the front passenger’s airbag. See
“Airbags”.
24
A second immediate action with
the key deadlocks the vehicle. It is
then impossible to open the doors
from the interior or exterior.
Note:
• With the vehicle stationary and
the engine switched off, locking is signalled by the flashing
of the interior locking control
warning lamp.
• If any of the doors, or the boot,
is open or not properly closed,
the central locking does not
operate.
Electronic immobiliser
The ELECTRONIC IMMOBILISER
DEVICE locks the engine supply
system.
The system activates automatically as the key is removed from
the ignition.
All the vehicle’s keys contain an
electronic immobiliser device.
After you switch on the ignition, a
dialogue starts between the key
and the electronic immobiliser
device.
If the key is not recognised, you
cannot start the vehicle
If this occurs, leave your vehicle immobilised and contact a
CITROËN dealer.
Never attempt to modify the electronic immobiliser’s electrical circuit, as this could render your
vehicle undriveable.
It is dangerous to operate the deadlocking when a person is inside the vehicle as unlocking is
impossible from the inside without the remote control.
The key number is on the label attached to the key.
Should the key be lost or modified (addition, cancellation or replacement), you must contact a CITROËN
dealer, with all of the vehicle keys in your possession as well as your proof of identity.
A nti - intru s ion alarm
B
Deactivation of the alarm
usng the remote control
The alarm is disarmed when you
unlock the vehicle (with a press on
button B on the remote control).
A
The anti-intrusion alarm provides:
• Exterior perimeter protection by
means of detectors on the vehicle
access points (doors, boot, bonnet).
• Electrical supply protection.
• Interior
volumetric
protection
by means of ultrasonic sensors
(detecting movement inside the
passenger compartment). This
can be deactivated using the control A.
• Anti-lifting protection by means of
sensors.
II
Deactivation of the alarm
with the key
The installation also has a siren,
and a warning lamp on the control A which is visible from outside
the vehicle, indicating the three
possible statuses of the alarm.
• Alarm not active (disarmed),
warning lamp off.
• Alarm active (armed), the warning lamp flashes slowly.
• Alarm triggered (signalling an
intrusion), the warning lamp
flashes rapidly if the alarm is
deactivated by a press on the
control B. It stops as soon as
you switch on the ignition.
Unlock the doors with the key. The
siren triggers. Enter the vehicle,
insert the key in the ignition and
turn it to the drive position to stop
the siren. Otherwise the siren will
continue for approximately 30 seconds.
Note: If there is a malfunction,
the warning lamp remains permanently on.
25
A nti - intru s ion alarm
B
C
You can operate the alarm with
perimeter protection only, by deactivating the volumetric protection (if
for example you wish to leave an
animal in the vehicle).
II
A
Operating the alarm
First make sure all the doors are
closed.
The alarm is armed by pressing
button C on the remote control.
With the alarm armed, the protections are active after 5 seconds
(perimeter) and 45 seconds (volumetric).
When the alarm is armed (on
standby), any intrusion will trigger
the siren for 30 seconds, accompanied by the direction indicators
lighting up.
The alarm then goes back on
standby. The triggering remains
memorised. The warning lamp on
button A flashes quickly when the
alarm is deactivated by pressing
the unlocking button B. This flashing stops when you switch on the
ignition.
26
Deactivating the volumetric
detection
Deactivation of the
volumetric detection
The siren is also triggered if there
is a cutting of the electrical supply. To stop it, restore the electrical
supply then press on the unlocking
button B.
Note:
• If you want to lock your vehicle
without arming the alarm, just
lock with the key only.
• If you lock your vehicle and a
door, or the boot, is still open,
the central locking does not
operate but the alarm will arm
itself after approx. 45 seconds.
Note: The siren is automatically
deactivated (for example for disconnecting the battery) as soon as
the vehicle is unlocked using the
remote control.
Switch off the ignition.
Within 10 seconds, press button A
until the warning lamp remains on
permanently.
Exit the vehicle.
Lock or deadlock the vehicle with
the remote control locking button.
The light on button A flashes once
a second.
Note: It is recommended to deactivate the volumetric detection when
washing the vehicle in order to prevent the random triggering of the
alarm.
Automatic activation
(depending on country)
The alarm is armed automatically,
2 minutes after the last door, or the
boot, has been closed.
In order to prevent the alarm from
triggering when you open one of
the doors or the boot, it is essential to press the unlocking button B
again on the remote control.
S T EE R I N G L O C K - I G N I T I O N - S TA R T E R
M: Drive position
The steering is unlocked (by turning the key in position M, if necessary move the steering wheel).
II
D: Starting
Release the key as soon as the
engine starts. Never turn it while
the engine is running.
Economy mode
S: Steering lock
To unlock the steering, gently move
the steering wheel while turning the
key, without exerting undue force.
When you remove the key, turn
your steering wheel to lock the
steering. The key can only be
removed when in position S.
NEVER REMOVE THE IGNITION KEY BEFORE THE ENGINE
HAS COME TO A COMPLETE STOP.
IT IS ESSENTIAL ALWAYS TO DRIVE WITH THE ENGINE
RUNNING, SO AS TO RETAIN STEERING AND BRAKING
ASSISTANCE (risk of the steering lock engaging and loss of safety
features).
When stationary, having removed the key, carefully turn the steering
wheel if you wish to lock the steering.
When the engine is stopped, some
functions (audio system, screen
wipe, electric windows, sunroof,
electric seats, telephone, video,
interior lighting etc.) are only
electrically supplied for a maximum
period of 30 minutes, to avoid
discharging the battery.
Once this period is over, a message
is displayed on the instrument panel
screen and the active functions are
placed on standby.
The electrical components relating
to comfort and also the headlamps
(not sidelamps or hazard warning
lamps) cut out automatically. To
reactivate them, it is necessary to
start the engine.
27
Starting
Manual gearbox
II
• Ensure that the gear lever is
in the neutral position.
• Do not touch the accelerator.
• For Diesel engines: Turn the
key to the drive position. Wait
for the preheater warning
lamp to go off, if this has
come on.
• Turn the key to action the
starter (not for more than ten
seconds), until the engine
starts.
Note: In ambient temperatures
lower than 0°C, depress the clutch
while actioning the starter to facilitate starting. Then release the
clutch pedal slowly.
Automatic gearbox
Check that you are in position P.
• Do not touch the accelerator.
• For Diesel engines: Turn the
key to the drive position. Wait
for the preheater warning
lamp to go off, if this has
come on.
• Turn the key to action the
starter (not for more than ten
seconds), until the engine
starts.
Note: Starting is possible in position N.
Advice
Diesel vehicles equipped
with a Turbo
Never stop the engine without having first allowed it to run at idle for
a few seconds, thus allowing the
turbo to return to normal speed.
Do not press the accelerator pedal
as the ignition is being switched
off. This could severely damage
the turbo unit.
Note: If the engine does not start at the first attempt, switch off the ignition.
Wait 10 seconds, then action the starter again as described above.
28
DO NOT RUN THE ENGINE IN A CLOSED SPACE OR IN ONE
THAT IS INSUFFICIENTLY VENTILATED.
I n s trum e nt pan e l
C
A
B
G
1
II
E
D
F
A Fuel gauge
B Indicator:
• Coolant temperature
• Cruise control/Speed limiter information
C Speed indicator
D Rev counter
E Indicator:
• Engine oil temperature
• Gear selector position and gear engaged (Automatic gearbox)
F Controls:
• Lighting rheostat
• Resetting to zero of trip mileage computer and
maintenance indicator
G Instrument panel screen indicating:
• Depending on the page selected with the left-hand
control knob on the steering wheel:
- Digital speed
- Trip computer
- Navigation (guidance) information
- Display of message alerts
- Engine oil level check
- Maintenance indicator
• Permanently:
- Trip mileage recorder
- Total mileage recorder
29
I n s trum e nt pan e l
W arning lamp s
Indicator and headlamp warning lamps
II
Left hand direction
indicator
See “Signalling”.
Right hand direction
indicator
See “Signalling”.
All the direction indicators flash simultaneously when the hazard
warning lamps are switched on.
See “Signalling”.
Front foglamps
See “Signalling”.
Main beams
See “Signalling”.
Foglamps (rear)
See “Signalling”.
Fuel low
Diesel engine
preheater
Electronic parking
brake - deactivation
of automatic
functions
Dipped beams
In some driving conditions and depending on
the engine, the range
may be less than 50 kilometres
(approx. 30 miles).
See “Fuel”.
30
Sidelamps
See method for starting
the engine.
See “Starting”.
See “Signalling”.
This warning lamp comes on if the
“automatic locking” (upon switching off the ignition) and the “automatic unlocking” functions are
deactivated or faulty.
I n s trum e nt pan e l
W arning lamp s
STOP warning
lamp
When the warning
lamp comes on,
you must stop the vehicle and
switch off the engine. Contact a
CITROËN dealer.
Parking brake
The permanent lighting of
this warning lamp confirms
that the parking brake is
applied.
If this warning lamp flashes, it indicates a fault with its application
or release. Consult a CITROËN
dealer as soon as possible.
See “Brakes”.
With the engine running, and
when displayed at the same time
as the STOP warning lamp, it indicates that the brake fluid level is
too low.
If this warning lamp comes on,
stop immediately and contact
a CITROËN dealer.
See “Brakes”.
Coolant temperature
It comes on for a few seconds each time you switch
on the ignition.
If this warning lamp comes on,
engine running, it tells you that
the coolant temperature is rising
abnormally.
This warning lamp is linked with
the STOP warning lamp.
It is essential to stop the vehicle.
Check the coolant level.
If the level is too low, contact
a CITROËN dealer.
SERVICE
This warning lamp
remains on permanently, as long as
the fault displayed on the instrument panel screen is present (for
serious faults).
Consult a CITROËN dealer as
soon as possible.
This warning lamp remains on
only for a short time for faults that
are minor.
Contact a CITROËN dealer.
II
ESP/ASR
Operating
If either of the ESP or ASR
systems is active, the warning
lamp flashes.
Battery charge
This warning lamp comes
on temporarily when the
engine is switched on. If it
remains on permanently,
contact a CITROËN dealer.
In the event of a battery failure,
the application of the electronic
parking brake when the engine
is switched off is not guaranteed.
You must therefore apply the
parking brake before switching
off the engine.
For a malfunction
With the engine running, the lighting of this warning lamp along
with a message on the instrument
panel screen, the lighting of the
SERVICE warning lamp and a
sound signal, indicates a system
fault.
Contact a CITROËN dealer.
Deactivation
The lighting of this warning lamp
and the light on the ESP deactivation button confirms that the system is deactivated.
See “Dynamic stability control”
(ESP).
31
I n s trum e nt pan e l
W arning lamp s
ABS
II
The ABS warning lamp
lights up when you switch
on the ignition: it should go
out after a few seconds. If it does
not go out, there could be a system malfunction.
See “Brakes”.
Depollution system
If the warning lamp flashes
or comes on whilst driving,
it indicates a problem with
the operation of the depollution system.
Consult a CITROËN dealer as
soon as possible.
Electronic parking
brake fault
This warning lamp comes
on if there is a fault with
the electronic parking brake.
Contact a CITROËN dealer.
32
Seat belt not fastened
(instrument panel)
This warning lamp lights
up on the instrument panel
to remind the driver and all passengers that they must fasten their
seat belt. It is linked to the seat
belt information given by the roof
console (see below).
Seat belt not
fastened
This
warning
lamp is located
on the roof console, in front of the
front interior lamp. It informs you
of the driver and passenger seat
belts which are not fastened.
The lit up locations represent the
seat positions which are not fastened.
Driver's seat belt not fastened:
• The warning lamp lights up
from 0 to 20 km/h (12 mph).
• Over 20 km/h (12 mph):
- the warning lamp flashes,
- a beep is repeated for about
2 minutes with 3 progressive
loudness levels.
Front and rear passengers seat
belt not fastened:
• When the ignition is switched
on, the locations corresponding
to the seat positions which are
not fastened remain lit up permanently for 30 seconds.
Seat belts unfastened whilst driving:
• The location corresponding to
the seat position unfastened
lights up from 0 to 20 km/h
(12 mph).
• Over 20 km/h (12 mph):
- the warning lamp corresponding to the seat position unfastened flashes,
- a beep is repeated for about
2 minutes with 3 progressive
loudness levels. The beeping
stops when the seat belt is
re-fastened or when a door is
opened when the vehicle has
stopped.
Front passenger's
airbag deactivation
warning lamp
See “Airbags”.
Front passenger's
airbag activation
warning lamp
See “Airbags”.
I n s trum e nt pan e l
Particl e filt e r
In addition to the catalytic converter, this filter contributes actively to the preserving of air quality, by collecting the
polluting particles that have not been burnt off. Black exhaust fumes are thus eliminated.
Clogging of the
particle filter
Clogging is caused by the particle
filter starting to be saturated (owing
to exceptionally long periods spent
driving in urban conditions : low
speeds, traffic jams, etc.).
In order to regenerate the filter you
are advised to drive as soon as possible, when traffic conditions allow,
at a speed of 60 km/h (approx.
37 mph) or more for at least 5 minutes. If the problem persists, contact a CITROËN dealer.
Note: If the vehicle has been running for long periods at very low
speeds or at idle, vapour emissions may be seen coming from
the exhaust under acceleration.
These have no consequences for
the running of the vehicle or for the
environment.
II
The simultaneous lighting of the
SERVICE warning lamp and the
display of the message “Risk of
saturation of particle filter (FAP)”
on the instrument panel screen
indicates an increased risk of saturation.
Contact a CITROËN dealer as
soon as possible.
DIESEL
additive
level
The simultaneous lighting of the
SERVICE warning lamp and the
display of the message “Particle
filter (FAP) additive level too low”
on the instrument panel screen
indicates that the additive needs to
be topped up.
Contact a CITROËN dealer as
soon as possible.
33
I n s trum e nt pan e l
T rip comput e r
B
Instantaneous information
II
A
C
Operation
The trip computer is displayed on
the instrument panel screen. It
gives you access to:
• 2 types of instantaneous
information:
- Range.
- Instantaneous consumption.
This information can be displayed in zone B of the instrument panel screen when you
switch the ignition on, immediately after the display of oil level
and/or maintenance information.
The different information to be
displayed is selected by rotating the control knob A.
34
• 3 types of information for
two journeys 1 and 2:
- Average speed.
- Average consumption.
- The distance travelled.
This information is displayed in
zone C of the instrument panel
by rotating the control knob A.
Range
This is the distance that can still
be travelled on the amount of fuel
remaining in the tank.
When the range is lower than
30 km (19 miles), only four dashes
are displayed.
Instantaneous consumption
This is the result from the consumption recorded within the last
2 seconds. This function is only
available when travelling at over
30 km/h.
I n s trum e nt pan e l
T rip comput e r / N AV I G AT I O N
Information for two journeys 1 and 2
A first rotation of control knob A on the steering wheel allows you to display
the information for journey 1.
Average speed
This is calculated (since the last
reset to zero of the trip computer)
by dividing the distance travelled
by the time taken (with the engine
running).
Average consumption
This is the relationship between
the fuel consumed and the distance travelled since the last reset
to zero of the selected journey.
Return to the main
instrument panel screen
display
Successive rotations of the control
knob A on the steering wheel allow
you to return to the main instrument panel screen display (vehicle
speed), via the navigation information screen, then the screen
displaying only the total mileage
and the trip mileage (bottom of
screen).
II
Distance travelled
This is the distance that has been
travelled since the last reset to zero
of the journey selected.
Journeys
Journeys 1 and 2 are independent
of each other but identical in use.
They allow you, for example, to
assign journey 1 for daily calculations and journey 2 for monthly calculations.
Reset a journey to zero
A second rotation of control knob A
allows you to display the information
for journey 2.
When the required journey is displayed, make a long press on the
left-hand control knob A on the
steering wheel.
Display of navigation
information on instrument
panel screen
You can display navigation information on the instrument panel
screen by rotating the left-hand
knob A on the steering wheel.
35
I n s trum e nt pan e l
C h e ck s / O il l e v e l
II
“Oil level correct” indicates normal operating.
A
Engine oil level indicator
Log of alerts
This function allows you to display
the log of alerts.
Press on button A. The following
messages appear consecutively
on the instrument panel screen:
• Tyre pressure check.
When you switch the ignition on,
the engine oil check is displayed
for a few seconds on the instrument panel screen.
Note: to ensure that this measurement is accurate, check the oil
level on horizontal ground after the
engine has been switched off for
at least 15 minutes. An incorrect
engine oil level can seriously damage your engine.
“Oil level incorrect” indicates that
the oil level is too low.
Check using the manual dipstick.
See “Levels”.
If, after topping up, the message
re-appears, contact a CITROËN
dealer.
• Maintenance indicator
reminder.
• Display of message alerts.
• Oil level check.
“Oil level measurement invalid”
indicates a malfunctioning of the
indicator.
Contact a CITROËN dealer.
36
I n s trum e nt pan e l
M aint e nanc e indicator
Maintenance indicator
It informs you when the next routine service is due in accordance with the vehicle servicing schedule in the Maintenance Guide. This information is dependent on two parameters: the mileage covered, and the time elapsed since
the last visit
Functioning if the distance to
the next service is less than
3000 km (approx. 1900 miles)
Functioning if the distance to
the next service is less than
1000 km (approx. 600 miles)
Operation if the service
interval has been passed
When switching on the ignition,
a message is displayed on the
instrument panel screen for a
few seconds. It indicates to you the
remaining distance before the next
service.
Example: there remain up to the
next service: 1900 miles.
When switching on the ignition,
a message is displayed on the
instrument panel screen for a few
seconds. It indicates to you the
remaining distance before the next
service.
Example: there remain up to the
next service: 500 miles.
When switching on the ignition,
a message is displayed on the
instrument panel screen for a
few seconds. It indicates to you
that the service interval has been
exceeded.
The routine service on your vehicle
needs to be carried out as soon as
possible.
A few seconds after the ignition is
switched on, the message disappears.
A few seconds after the ignition is
switched on, the message disappears, then the maintenance symbol (spanner) remains lit.
A few seconds after the ignition is
switched on, the message disappears, then the maintenance symbol (spanner) remains lit.
II
37
I n s trum e nt pan e l
M aint e nanc e indicator
II
A
Resetting to zero of the maintenance indicator
If you are carrying out the service yourself, the procedure for resetting to
zero is as follows:
• Swicth off the ignition, then move the key to position S, anti-theft.
• Press on button A and keep it pressed.
• Switch on the ignition. The instrument panel screen counts down from
10 to 0 and displays the maintenance symbol.
• Hold down button A until the zero appears and the maintenance symbol
disappears.
• Switch off the ignition.
38
I n s trum e nt pan e l
M ain M e nu
A
The main menu allows you to programme certain vehicle and instrument panel functions:
II
“Vehicle parameters” menu
This allows you to access the
parameters relating to:
• The vehicle lighting.
• The comfort levels in the vehicle.
See “Instrument panel - Vehicle
parameters”.
B
The instrument panel B is located
in the centre of the dashboard.
With the vehicle stationary, you
can access the main menu of the
instrument panel by quickly pressing on the left-hand rotating control A on the steering wheel.
Note: The message “Action
impossible whilst driving” is displayed on the instrument panel
if you try to open the main menu
whilst driving.
“Choice of units” menu
This allows you to choose metric or
imperial units.
“Choice of language” menu
This allows you to choose the
display and voice recognition language.
39
I n s trum e nt pan e l
V e hicl e param e t e r s
“Vehicle parameters” menu
II
This menu can be accessed from
the instrument panel “Main menu”.
It allows you to set the lighting and
comfort settings for your vehicle.
“Lighting” menu
Once you have selected this menu,
you can:
• Activate/deactivate the lighting
of the daytime-running lamps*.
• Activate/deactivate the guideme-home lighting and adjust its
duration.
• Activate/deactivate the dualfunction
Xenon
directional
headlamps.
“Comfort” menu
Once you have selected this menu,
you can:
• Activate/deactivate the driver's
welcome lighting function.
• Select the unlocking of all the
doors or just the driver's door.
• Activate/deactivate the automatic engaging of the electric
parking brake.
40
* Depending on country.
I n s trum e nt pan e l
A
II
1
2
Engine oil temperature
gauge
Under normal operating conditions, the bars should be within
section 1.
In severe operating conditions, the
bars may extend into section 2.
In this event, slow down, and if necessary, stop the engine and check
the levels (see chapter - Maintenance - “Levels”).
1
2
Coolant temperature
indicator
Under normal operating conditions, the bars should be within
section 1.
In severe operating conditions, the
bars may extend into section 2, the
engine coolant temperature warning lamp A and the STOP warning
lamp will light up, stop immediately. Switch off the ignition. The
cooling fan may continue to
operate for a certain time. Allow
the engine to cool down while taking the precautions indicated in
chapter - Maintenace - “Levels”.
Contact a CITROËN dealer.
If the SERVICE warning lamp lights
up, check the levels (see chapter Maintenance - “Levels”).
Fuel gauge
On horizontal ground, the lighting
of the fuel low warning lamp warns
you that you are using the reserve
tank.
A message alert is displayed on
the instrument panel.
41
F ix e d c e ntr e d control s s t e e ring
wh e e l
Rotate
II
1
1
3
2
2
10
4
3
5
4
9
6
8
Short press
- Open the instrument panel menu (only when vehicle stationary)
- Select and validate information
Long press
Reset the trip computer (if the trip computer page is displayed)
Short press
- Cancel the current operation
- Return to the previous instrument panel display
Long press
Return to the original instrument panel display
Short press
Press and hold
Short press
Press and hold
Reduce speed in steps of 1 km/h/memorisation of speed
Reduce speed in steps of 5 km/h
Short press
Suspend or restart cruise control/speed limiter (depending on mode selected)
6
Short press
Select cruise control or speed limiter (the cycle on this button always starts with the speed limiter
selector)
7
Short press
Deactivation
Short press
- Pick up an incoming call
- Hang up during a call
- Open the contextual telephone menu
- Validate in the telephone list or menu
Long press
Refuse an incoming call
8
9
Short press /
Long press
Horn
10
Short press
Activation/deactivation of Black Panel mode (night driving)
Short press
Activation of voice recognition
Long press
Reminder of navigation guidance
11
42
Increase speed in steps of 1 km/h/memorisation of speed
Increase speed in steps of 5 km/h
5
7
11
- Scroll through the different information screens on instrument panel
- Move through the different instrument panel menus
- Increase/reduction of values
F ix e d c e ntr e d control s s t e e ring
wh e e l
Rotate
11
- Radio source: Scroll through pre-set stations
- CD/CD MP3/CD changer/jukebox source: Scroll through CDs and directories
- In the multifunction display menus: Move around and increase/decrease
Short press
- In the multifunction display menus: Validation
- Open the shortcut menus (depending on the multifunction display page)
Long press
Open the multifunction display main menu
Short press
Cancel the current operation and return to the previous multifunction display screen
Note: For an incoming call: Refuse the call
Long press
Return to the original multifunction display
13
Short press
Access the multifunction display main menu
14
Short press /
Press and hold
Increase volume
15
Short press /
Press and hold
Decrease volume
12
16
17
Short press
- First press: mute
- Second press: cancel mute
Short press
- Radio source: Automatic search of higher frequencies
- CD/CD MP3/CD changer/jukebox source: Search of the next track
Press and hold
18
Short press
Press and hold
19
II
11
12
13
14
15
20
16
17
19
- CD/CD MP3/CD changer/jukebox source: Fast forward with accelerated sound
- Radio source: Automatic search of lower frequencies
- CD/CD MP3/CD changer/jukebox source: Search of previous track
18
- CD/CD MP3/CD changer/jukebox source: Rapid reverse with accelerated sound
Short press
- Radio source: Display of the list of radio stations available
- CD/MP3 CD and CD changer source: Display of the list of CD tracks and directories
- Jukebox source: Display of the list of albums
Long press
Updating of the list of radio stations
20
Short press /
Long press
Horn
21
Short press
MODE : selection of the type of information displayed on the multifunction screen
21
43
Signalling
Emergency operation of
hazard warning lamps
A sudden deceleration of the vehicle causes the hazard lamps to
come on automatically.
They will cease to operate automatically, or manually if you press
the hazard lamps button on the
dashboard.
II
Direction indicators
Left, downwards.
Right, upwards.
For a change of direction, move
the control stalk beyond the tight
spot. The indicator is automatically
cancelled when the steering wheel
returns to its normal position.
Hazard warning lamps
This operates all the direction indicators simultaneously.
Only use them to indicate danger, for an emergency stop or for
driving in abnormal conditions.
The hazard lamps can also be
used with the ignition switched off.
“Motorway” function
Move the stalk briefly upwards or
downwards, without going beyond
the resistance point; the direction
indicators will flash 3 times.
44
The direction indicators cannot operate if the hazard warning lamps
are on.
Signalling
2
1
A
3
4
Lighting control stalk
1 : Off.
2 : Automatic lighting.
3 : Sidelamps.
4 : Dipped beams / Main beams.
All vehicle lamps off
Rotate the ring A forwards.
Automatic lighting of
headlamps
The sidelamps and the dipped
beams come on automatically
when the light is insufficient or if
the windscreen wipers are in continuous operation.
They go out once the brightness
has reached a satisfactory level
or about 5 minutes after the windscreen wipers have stopped.
To activate this function, turn the
ring A to position 2.
Take care not to cover the brightness sensor, which is visible
from outside the windscreen,
behind the interior rear view mirror.
Rotate the ring A forwards.
Sidelamps on
Rotate the ring A forwards.
Dipped beams/
main beams on
Pull the control stalk towards you
to change between dipped beam
and main beam.
II
Manual headlamp height
adjustment
You are advised to adjust the aim
of the headlamps in accordance
with vehicle load.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
-. Intermediate setting.
2. 5 people + maximum permitted
load.
-. Intermediate setting.
3. Driver + maximum permitted
load.
Visible alert / headlamp
flash
Pull the control towards you.
The headlamp flash can be made
even with the ignition switched off.
45
Signalling
II
B
A
Guide-me-home lighting
With the ignition off, this function
temporarily switches on your headlamps to give you exterior lighting
when leaving your vehicle.
This function is activated:
• Manually by pulling the lighting
stalk towards you, ignition off.
• Automatically in the following
conditions:
- automatic headlamp lighting
is activated,
- guide-me-home lighting is
activated.
- brightness conditions are low.
- using button A on the remote
control.
You can modify the length of time
guide-me-home lighting stays on
for (around 60, 30 or 15 seconds)
using the “Main Menu” of the instrument panel screen.
See “Instrument panel screen”.
46
To do so, select “Vehicle parameters / Lighting”, then adjust the time
for guide-me-home lighting.
Sound signal for headlamps
left on
This operates when the driver's door
is opened, ignition off, to indicate that
the vehicle lamps are still on.
It stops when you close the door,
switch off the lamps or switch on the
ignition.
This signal does not operate if the
automatic lighting of headlamps
or the guide-me-home lighting are
active.
Daytime-running lamps
They light up automatically and permanently, when the engine is running, if:
• The function is activated* in the
“Main Menu” of the instrument
panel screen. See “Instrument
panel screen”.
• The lighting control is at position 0 or AUTO.
• All the headlamps are off.
Note : you can deactivate* this
function using the “Main Menu” of
the instrument panel screen. See
“Instrument panel screen”.
Front and rear
foglamps (Ring B)
These
operate
in
conjunction with the
sidelamps, the dipped
beams or the main
beams.
For vehicles fitted with rear
foglamps:
- 1st turn forwards: lighting of rear
foglamps.
- 1st turn rearwards: extinction of
rear foglamps.
For vehicles fitted with front
and rear foglamps:
- 1st turn forwards: lighting of front
foglamps.
- 2nd turn forwards: lighting of rear
foglamps.
- 1st turn rearwards: extinction of
rear foglamps.
- 2nd turn rearwards: extinction of
front foglamps.
Note: the foglamps should be used
only in fog or in other conditions of
poor visibility.
In foggy conditions, if the ambient light is not such that
the headlamps come on automatically, it is up to the driver
to switch on dipped beams, and/or foglamps, manually.
* Depending on country.
B e nd lighting
With dipped or main beams, this function provides additional lighting for the inside of a bend.
This lighting is most useful when travelling at low and medium speed (urban driving, winding road, intersections...).
II
Operation
This lighting is activated past a certain angle of rotation of the steering wheel. It is deactivated with
the vehicle stationary or at very
low speed, or with reverse gear
engaged.
Without bend lighting
With bend lighting
47
X e non dual function dir e ctional
h e adlamp s - A ngl e d lighting
II
With dipped beams or main beams, the Directional headlamps function turns the headlamps in the direction the
road ahead is taking. Your vision on bends is considerably enhanced.
This function is activated once your vehicle speed reaches 10 km/h (6 mph) and stops when your speed decreases
to 5 km/h (3 mph).
Note: An automatic correction of the beam height enables you not to dazzle other drivers.
Activation/Deactivation
Activated by default, this function
can be activated/deactivated in
the “Main Menu” of the instrument
panel screen. To do so, select
“Vehicle parameters / Lighting /
Directional headlamps”.
The activated/deactivated status
is retained when you switch off
the engine.
Note: This function is not active
when the vehicle is stationary,
moving at very low speed, or in
reverse gear.
Function deactivated
Function activated
This device is linked with the Angular lighting which lights up the inside of a bend when the vehicle speed is lower
than 40 km/h (25 mph). This maximises the lighting at intersections and when parking, for example.
The angular lighting is deployed:
• When the direction indicators are activated,
and/or
• from a certain angle of rotation of the steering wheel.
Note: The angular lighting is deactivated when the directional headlamps are deactivated.
48
If there is a malfunction, the “Dipped beams” warning lamp flashes, accompanied by a message
on the instrument panel. Contact a CITROËN dealer.
W ip e r s
FRONT WIPERS
Control positions
2: Rapid wipe.
1: Normal wipe.
I: Intermittent wipe.
0: Off.
One press downwards:
• AUTO: Automatic wipe activated.
• Single wipe.
Position I: The speed of the wipers will adjust itself to the speed of
your vehicle.
Positions 1 and 2: When the vehicle is stationary, the speed of the
wipers will reduce automatically.
For safety, the wiper system is
deactivated when the ignition is
switched off.
Automatic wipe: To activate automatic wipe, place the control stalk
on position 0, then press it downwards. The activation of this mode
is confirmed by one wipe and a
message on the instrument panel
screen. The wipe speed will adjust
according to the intensity of the
rain.
Note:
• Pulling the stalk downwards will
produce a single wipe, without
deactivating automatic wiping.
• Automatic wiping is not retained
once the engine is switched
off.
II
Screen wash
Pull the screen wipe control stalk
towards you.
The screen wash is accompanied
by a timed wipe sequence. If the
dipped beams are on, it is also
accompanied by a timed headlamp
wash.
Deactivation of automatic
wipe:
• Go to position I, then return to
position 0.
• Or stop the engine.
Do not cover the rain detector which is located behind the interior
rear view mirror and visible from outside the windscreen.
Using an automatic car wash: switch the ignition off to avoid the wiping system activating.
49
W ip e r s
Changing the wiper blades
II
If changing the wiper blades, they
must be stopped in the maintenance position. For this, switch
off the ignition and then within one
minute move the wiper control
stalk. The wipers stand up vertically.
After replacement, switch on the
ignition and move the wiper
control stalk so that the wipers
resume their normal position.
Remark: The maintenance position can also be used in snowy
conditions to avoid a build up of
snow.
A
REAR WIPERS AND WASH
(TOURER)
Rotate control A to the desired
position.
Off
Intermittent wipe
Screen wash
50
Check that the wipers can operate freely in freezing temperatures.
Remove any accumulation of
snow at the base of the windscreen.
The screen wash is accompanied
by a timed rear wipe sequence.
W indow s
Electric operation
The driver uses the controls located
on the door to operate the vehicle’s
electric windows.
Note: The windows can also be
operated for a short period after
the ignition has been switched
off (including after the front doors
have been opened).
Sequential operation
An action on the control to the first
notch causes a window movement
which stops as soon as the control
is released.
An action on the control to the
second notch causes the window
to close or open completely, a further press on the control stops the
movement.
Child safety
This deactivates the controls in the
rear of the vehicle, both for the rear
windows and for opening the rear
doors from the inside.
This is activated by a press on button A located on the window control panel. The warning lamp on
button A lights up.
A message on the instrument panel
informs you of the activation/deactivation of child safety.
You can still open the doors from
outside and operate the rear electric windows from the front of the
vehicle.
Always pay attention to where children are when
opening or closing the windows
Always remove the ignition key when leaving the vehicle, even if for
a short time.
If the driver is operating the electric window controls for passengers, he or she should ensure that no passenger is obstructing the
window from closing.
The driver must ensure that the electric windows are used properly
by passengers.
Should there be any risk of a person becoming trapped by a window
closing, you should immediately reverse the window movement. To
do this, press on the control concerned.
II
A
Anti-pinch
An anti-pinch device stops the
window from rising. If it meets an
obstacle, it goes back down.
If there is a malfunction, sequential operation is deactivated. When
you raise the window again, press
the control each time the window
stops until you reach the desired
position. You must then re-initialise the function for each electric
window:
• Lower the window fully using
the control, then close. It will
rise only a few centimetres.
Press repeatedly on the control
until the window is fully closed.
• Keep the control pressed down
for at least 1 second having
closed the window.
During this operation,
the anti-pinch protection
does not work.
51
St e e ring column adju s tm e nt – S e at b e lt h e ight adju s tm e nt
II
A
Adjustment of height and
reach of steering wheel
With the vehicle at rest, unlock
the steering wheel by pushing control A forwards.
Adjust the height and the reach
of the steering wheel, then lock
the position by pulling the lever
upwards.
52
Seat belt height adjustment
The correct positioning of the belt
strap is through the middle of the
shoulder. See “Seat belts”.
To adjust the seat belt for height,
compress the control and slide it
in the desired direction.
As a matter of safety, the adjustments in your driving position must be made only while the vehicle
is stationary.
First adjust your seat to the most suitable position, then adjust the position of the steering wheel.
See “Driving position”.
F ront s e at s
M anual adju s tm e nt s
1.Adjustments to the height and
angle of the head restraint
To raise it, pull upwards.
To lower it, press on the control A to unlock
it, and simultaneously on the head restraint
itself. The adjustment is correct when the
top edge of the head restraint is at the same
height as the top of the head. It is also tiltadjustable.
To raise it, press control A to unlock it, then
pull it upwards.
2.Adjustment of the backrest angle
1
II
A
5
2
Use the control to adjust the backrest
angle.
It is possible to recline the backrest angle to
45° by pushing it until it locks.
3.Adjustment of the seat height and
angle
3
4.Longitudinal adjustment of seat
6
4
Raise or lower the control the number of
times required to obtain the desired position.
Lift the control bar and adjust to the desired
position.
5.Adjustment of lumbar support
Turn the control and adjust to the desired
position.
6.Heated seat controls
Note: The heated seats only operate when
the engine is running.
0: Off.
1: Gentle.
2: Medium.
3: Strong.
For your safety, do not
drive with the head
restraints removed ;
these must be in
place and correctly
adjusted.
53
F ront s e at s
El e ctrical adju s tm e nt s
II
To adjust the electrical seats,
switch on the ignition or start the
engine if the vehicle has gone into
economy mode.
1
a
1.Adjustment of the seat
height and angle, and
longitudinal adjustment
b
a Raise or lower the front of
the control in order to raise or
lower the front of the seat.
c
b Raise or lower the rear of the
control in order to raise or
lower the rear of the seat.
c Simultaneously raise or lower
the front and rear of the control in order to raise or lower
the entire seat.
d Slide the control forwards or
backwards to move the seat
forwards or backwards.
2.Adjustment of the
backrest angle
Move the control forwards or
backwards to adjust the backrest angle.
3.Adjustment of the angle
of the top of the backrest
54
Move the control forwards or
backwards to adjust the angle
of the top of the backrest.
d
4
4.Adjustment of lumbar
support
3
This function allows you to independently adjust the height and
level of lumbar support.
Move the control:
• Forwards or backwards to
increase or reduce the lumbar
support.
• Upwards or downwards to
raise or lower the lumbar support zone.
2
Note: Seat adjustments are also
possible for a short period after
opening one of the front doors or
switching off the ignition.
F ront s e at s
El e ctrical adju s tm e nt s
Controls for the heated
seats
B
The front seats can be heated individually. With the engine running,
use control A, located beside the
seats to choose between three
heating levels:
II
D
C
A
0: Off.
1: Gentle.
2: Medium.
3: Strong.
The Welcome function
When the driver's door is opened
and the ignition is off, the seat
moves to ease accessing or leaving the vehicle.
Take care not to hinder the forwards or backwards movement of
the seat.
You may activate or deactivate this
function using the “Main Menu” on
the instrument panel screen. To do
so, select “Vehicle parameters /
Comfort / Driver welcome”.
Massage function
This function provides the driver
with a back massage.
To activate the massage, with the
engine runnuing, press on button B. The warning lamp comes on
and the massage function is activated for a period of 1 hour. During
this time, massage is performed
in cycles of 6 minutes (4 minutes
of massage followed by 2 minutes
break). In total, the system will perform 10 cycles.
After 1 hour, the function is deactivated. The warning lamp goes out.
You can deactivate the massage
function at any time by pressing on
button B.
Head restraint height and
angle adjustments on
electric seats
To adjust the angle of the head
restraint, push back or pull forward
section C of the head restraint until
you reach the desired position.
To raise it, pull upwards.
To lower it, press on the control D
to unlock it, and simultaneously on
the head restraint itself.
To raise it, press control D to unlock
it, then pull it upwards.
55
M e mori s ation of driv e r ' s
adju s tm e nt s
1
2
II
M
The memorisation function allows
you to make the following dashboard adjustments:
• Driver's seat.
• Exterior rear view mirrors.
• Air conditioning (temperature
and air flow).
You have the possibility to memorise two driving positions using
buttons 1 and 2.
56
Memorisation of driving
positions
a. Place the igntion key in “Drive”
position (second position).
b Adjust your seat, the exterior
rear view mirrors and the air
conditioning.
c Press successively on button
M then on button 1 (first driving
position) or 2 (second driving
position).
The memorisation is confirmed by
a sound signal.
Note: The memorisation of a
new driving position cancels and
replaces the previous one.
Recall of a memorised
driving position
Vehicle stationary (ignition
on or engine running)
Press briefly on button 1 or 2 to
recall the corresponding memorised position.
The completion of the adjustments
is confirmed by a sound signal.
Vehicle in motion
Keep button 1 or 2 pressed down
to recall the corresponding memorised position.
R e ar vi e w mirror s
Operation
2
1
Interior rear view mirror
The lever on the lower edge enables you to place the rear view mirror in either of two positions.
Day position: the lever is not visible.
Night position (anti-dazzle): the
lever is visible.
Press on button 1.
• Warning lamp 2 on: automatic
mode.
• Warning lamp 2 off: automatic
mode stopped. The mirror
remains in its lightest definition.
Note: In order to ensure optimal
visibility when manoeuvring, the
interior and exterior rear view mirrors lighten when reverse gear is
engaged.
II
Automatic electrochrome
interior and exterior rear
view mirrors
These provide an automatic and
progressive change between day
use and night use.
To prevent dazzle, the mirrors automatically become darker as a function of the intensity of light coming from the rear. They become
lighter as soon as the brightness
diminishes, thus ensuring optimal
vision.
57
R e ar vi e w mirror s
Fold-back of door mirrors
II
2
1
Electric door mirrors
adjustment
This can operate when the ignition
is switched on.
The driver selects the rear view
mirror by moving control 1, to the
left or to the right, then adjusts the
mirror in the four directions by acting on control 2.
Demisting-deicing of the rear view
mirrors is linked with that for the
rear screen.
The adjustments you have made to
the rear view mirrors are included
in the memorisation of driving positions. See “Memorisation of driver's adjustments”.
58
When the vehicle is parked, the
door mirrors can be folded back
either manually or electrically.
Electric fold-back
From the central position, one
press towards the rear on control 1
folds the rear view mirrors back.
To return them to the initial position,
press again on control 1 towards
the rear.
Automatic fold-back on
locking
Automatic fold-back operates when
you lock the doors.
The opposite movement will take
place on unlocking, unless foldback has been requested using
control 1 before switching off the
ignition.
Note: Automatic fold-back of the
rear view mirrors can be deactivated. Contact a CITROËN
dealer.
In reverse gear: adjustment
of the indexed positions for
the passenger’s and driver’s
rear view mirrors
With the engine running:
1. Select the (driver's or passenger's) rear view mirror using
control 1.
2. Engage reverse gear, the mirror
glass automatically positions
itself to improve your vision of
the pavement.
3. Adjust the mirror to your preference using control 2.
These adjustments are automatically memorised.
The rear view mirrors resume their
original position:
• 20 seconds after reverse gear
is disengaged.
• Once the vehicle reaches a
speed of over 10 km/h (6 mph).
Deactivation of the driver's
and passenger's indexed
rear view mirrors function
To deactivate the function, move
control 1 to the central position.
Note: this action cancels the
indexing of the rear view mirrors if
in progress.
M ultifunction di s play
1
2
B
C
B
D
C
3
II
A
A
The driver is recommended not to
concern himself with the display
controls while driving.
1. Time.
2. Outside temperature.
3. Date - Display zone.
When the outside temperature
is between +3 °C and –3 °C, the
temperature display flashes (risk
of ice).
Controls
A. Access to the multifunction display main menu.
B. Cancellation of the operation or
return to the previous display.
C. Scrolling through the multifunction display menus.
Validation using steering wheel
controls.
D. Validation using radio panel.
Note: The outside temperature
displayed may be higher than the
actual temperature if the vehicle is
stationary in bright sunlight.
Main Menu
Press on control A to the right of
the steering wheel to display the
multifunction display “Main Menu”.
This menu gives you access to the
following functions:
Display configuration,
allowing you to adjust:
• The display brightness
and contrast.
• The time and date.
• The units used for the
outside temperature
display.
Radio - CD
(See “Radio” chapter).
Bluetooth ® hands-free
kit
(See “Radio” chapter).
C
Display configuration
To adjust the display
brightness and contrast:
1 Press on A.
2 Using C, select the “Brightness video adjustments” menu. Confirm by pressing on C on the
steering wheel or on D on the
radio panel.
3 Select the display configuration with a press on C. Confirm
by pressing on C on the steering wheel or on D on the radio
panel.
4 Select the brightness adjustment. Confirm by pressing on C
on the steering wheel or on D
on the radio panel.
5 Using C, select normal or alternative display mode, then validate by pressing on C on the
steering wheel or on D on the
radio panel. To adjust the brightness, select “+” or “-” and confirm the adjustment by pressing
on C.
6 Validate “OK” on the screen.
59
M ultifunction di s play
B
C
B
D
C
II
A
A
To adjust the date and the
time:
1 Press on A.
2 Using C, select the “Date and
time adjustment” menu. Confirm by pressing on C on the
steering wheel or on D on the
radio panel.
3 Select the display configuration with a press on C. Confirm
by pressing on C on the steering wheel or on D on the radio
panel.
4 Using B, adjust the date and
time, then confirm by pressing
on C on the steering wheel or
on D on the radio panel.
5 Press C to select the values
you wish to modify. Confirm
by pressing on C on the steering wheel or on D on the radio
panel.
6 Validate “OK” on the screen.
60
To choose the units for
the outside temperature
display:
1 Press on A.
2 Using C, select the “Choice of
temperature unit” menu. Confirm by pressing on C on the
steering wheel or on D on the
radio panel.
3 Select the unit using C. Confirm
by pressing on C on the steering wheel or on D on the radio
panel.
4 Validate “OK” on the screen.
Selection of the type of
information displayed
(MODE)
Consecutive presses on the end
of the wiper control stalk or the
MODE button on the radio allow
you to select the type of information presented on the multifunction
display (date or radio/CD/CD MP3/
CD changer).
M ultifunction di s play
T e l e matic s
1
2
3
4
B
B
C
D
C
II
A
E
A
1 Outside temperature.
2 Date.
3 Telephone.
4 Time.
When the outside temperature
is between +3 °C and –3 °C, the
temperature display flashes (risk
of ice).
Note: The outside temperature
displayed may be higher than the
actual temperature if the vehicle is
stationary in bright sunlight.
The driver is advised not to use the
controls described opposite whilst
driving.
Controls
A. Access to the telematics multifunction display menu.
B. Cancellation of the operation or
return to the previous display.
C. Scrolling through the menus of
the telematics multifunction display. Validation using steering
wheel controls.
D. Validation using radio panel.
E. Selection of the type of information presented on the telematics multifunction display (date,
radio/CD/CD MP3/CD changer/
jukebox, navigation information,
telephone).
Main Menu
Press on button A to display the
telematics multifunction display
“Main Menu”. This menu gives you
access to the following functions:
Navigation/guidance
See NaviDrive instructions.
Map
See NaviDrive instructions.
Traffic information
See NaviDrive instructions.
Audio
See NaviDrive instructions.
Telephone and
telematic services
See NaviDrive instructions.
Configuration,
allows you to adjust various
settings (date, time...).
Video Menu,
allows you to adjust various video settings.
61
M ultifunction di s play
T e l e matic s
To adjust the date and the time:
• Press on the MENU button.
• Rotate the control to select the Configuration icon.
• Press on the control to validate.
II
In the configuration menu:
• Rotate the control to select the menu A.
• Press on the control to validate.
A
or
• Rotate the control to select the menu B.
• Press on the control to validate.
or
Rotate the control to select a field:
- C for the day
- D for the month
- E for the year
- F for the time.
• Press on the control to validate.
• Rotate the control or use the alphanumeric keypad to select the digits that
make up the date and the time.
• Press on the control to validate each field.
Rotate the control to select:
- G for 12 hour mode.
- H for 24 hour mode.
- I for an automatic adjustment of minutes thanks to GPS.
• Press on the control to validate.
62
B
Other functions of the configuration menu: See NaviDrive instructions.
C
D
E
F
G
I
H
M anual g e arbox
II
A
5 speed gearbox
6 speed gearbox
Reverse gear
Reverse gear
Do not select reverse gear until the
vehicle is completely stationary.
Depress the clutch pedal and wait a
few moments before gently engaging reverse gear.
Lift the collar A to engage reverse
gear.
Do not select reverse gear until the
vehicle is completely stationary.
Depress the clutch pedal and wait a
few moments before gently engaging reverse gear.
63
A utomatic g e arbox
II
C
A
B
4 and 6 speed automatic
gearbox
• Parking (Position P).
• Reverse gear (Position R).
• Neutral (Position N).
64
• The automatic gearbox offers
you:
- Operation in auto-active
mode, with automatic adaptation to your style of driving
as well as to the road profile
(Position D).
- Operation
in
sequential
mode, with manual gear
changing (Position M).
- Operation
in
automatic
SPORT mode (Position D)
and press button A.
- Operation
in
automatic
SNOW mode (Position D)
and press button B.
For safety:
• The gear lever can only be disengaged from position P if
you are pressing the brake pedal.
• When the driver's door is opened, a beep sounds if the
gear lever is not in position P.
• Before leaving the vehicle, make absolutely certain that
position P is selected.
Position of the gear selector
The driving mode and the position
of the gear lever are displayed in
dial C of the instrument panel.
A utomatic g e arbox
The engine can only be started
when the lever is at position P
or N.
A safety device ensures that starting is impossible in the other positions.
Once the engine has been started,
with the gear lever at P, press on
the brake pedal then place the
lever at:
• D for automatic mode.
• R for reverse gear.
• M to change to manual mode.
The change from position D (driving in automatic mode) to position M (driving in sequential mode)
or vice versa can be made at any
time.
The gear selected is displayed on
the instrument panel.
Reverse gear
Do not engage until the
vehicle is stationary, foot
on brake. To avoid gearbox snatching, do not accelerate
immediately after the selection.
Note: Juddering may be felt when
changing from position P to R on a
steep gradient.
II
Neutral
Using the automatic
gearbox
Do not select position N
if the vehicle is moving,
unless
absolutely
necessary
(vehicle
being
towed).
Parking
To avoid any movement of
the vehicle when parked,
place the gear lever to P.
Do not engage until the vehicle is
completely stationary. In this position, the driving wheels are locked.
Check that the selector is in the
correct position. Securely apply
the parking brake.
• Do not select position N if the vehicle
is moving (except in
absolute necessity).
• Never select positions P
or R if the vehicle is not
completely stationary.
If while the vehicle is moving you inadvertently select
position N, leave the engine
to idle before engaging position D or M.
65
A utomatic g e arbox
Remarks:
• During braking, the gearbox
may kick down automatically
in order to offer an effective
engine brake.
• If you suddenly lift your foot off
the accelerator, the gearbox will
guard your safety by not changing up again.
II
Automatic forward drive
(lever at position D)
The gearbox always selects the
gear best adapted to the following
parameters:
• Style of driving.
• Road profile.
• Vehicle load.
In this way the gearbox operates
without the need for your intervention.
For certain manoeuvres (e.g. overtaking), it is possible to obtain
maximum acceleration by pressing hard all the way down on the
accelerator pedal, which may trigger automatic changedown to a
lower gear.
66
Sequential forward drive
(lever at position M)
Position M allows you to change
gear manually:
• Push the lever towards “+” to
change up a gear.
• Pull the lever towards “-” to
change down a gear.
Note:
• Passage from one gear to
another is only possible when
vehicle speed and engine
speed permit.
• The “SPORT” and “SNOW”
modes are not available in
sequential operation.
• If the engine speed is too high,
the
gearbox
automatically
selects a higher gear.
• If the engine speed is too low,
the
gearbox
automatically
selects a lower gear.
A utomatic g e arbox
A
B
Operation in SPORT or
SNOW automatic mode
Lever at D:
Press on button A to select the
SPORT driving mode.
Press on button B to select the
SNOW driving mode.
Pressing again on button A or B
returns you to NORMAL driving
mode.
SPORT mode is for more
responsive driving, to provide maximum performance and acceleration.
The instrument panel display lights
up.
NORMAL mode is selected by
default when the engine is started.
This driving mode is suitable for
normal driving conditions.
No warning lamp will light up in the
instrument panel.
SNOW mode facilitates
starting and smooth driving
when road adherence conditions are poor.
The instrument panel display lights
up.
The
driving
mode
Remark:
selected before you switched off
the engine will be retained the next
time you start up.
II
If there is an operating fault, the gearbox
is stuck in a gear, do
not exceed 100 km/h
(approx. 60 mph).
Juddering may be felt when
selecting R for reverse gear
or when returning to position D.
Consult a CITROËN dealer as
soon as possible.
Do not stop your engine if
the gear selector lever is in
position D or R.
67
C rui s e control
II
1
2
3
A
4
5
This driving assistance function
allows you to drive at the speed of
your choice without the need to
action the accelerator. It is active
over speeds of around 40 km/h
(25 mph).
Remark: For the function to be
active, the gearbox must be in at
least:
• 4th gear for manual gearboxes.
• 2nd gear for automatic gearboxes.
The cruise control controls are
located on the left-hand side of the
steering wheel and cruise control
information is displayed in zone A
of the instrument panel.
68
To select the function
Press button 4 to select cruise control mode “CRUISE”.
The selection is confirmed by the
display of the function in zone A of
the instrument panel.
When the function is selected, no
cruising speed has yet been
memorised.
Once the desired speed has been
reached using the accelerator,
press button 1 or button 2. The
cruising speed is then memorised
and cruise control is activated.
The cruising speed is displayed
in zone A of the instrument panel,
and “ON” is displayed.
You can then release the accelerator pedal. The vehicle will automatically keep to the speed chosen.
Note: The vehicle speed may vary
slightly from that memorised.
If during cruise control the system
cannot keep to the cruise speed
(e.g. on a steep descent), then the
speed flashes. If necessary, brake
to curb your speed.
Adjustment of the
memorised speed while
cruise control is in
operation
You can adjust the memorised
speed, displayed in zone A, by
pressing:
• Button 1 to increase the speed.
• Button 2 to reduce the speed.
Remark: Successive presses will
modify the cruise speed in steps of
1 mph and a continuous press in
steps of 5 mph.
C rui s e control
Temporary override of the
cruise speed
While cruise control is in operation,
it is always possible to go above the
cruise speed simply by pressing
the accelerator pedal (for example
to overtake another vehicle).
The speed displayed in zone A
flashes.
You only have to release the accelerator pedal to return to the cruising speed.
Suspension or resumption
of cruise control with a
memorised speed
• Either by pressing the brake
pedal or the clutch pedal.
• Or by pressing button 3.
• Or by the ESP or ASR systems
being active.
Note: for vehicles with a manual
gearbox, cruise control is deactivated if the gear lever is in neutral.
“PAUSE” will be displayed in
zone A of the instrument panel.
These actions do not cancel the
cruising speed which remains displayed on the instrument panel.
Reactivation of cruise
control
• By recalling the memorised
speed:
After deactivation, press button 3. Your vehicle automatically returns to the memorised
cruising speed. The memorised
speed and “ON” are displayed
in zone A.
If the memorised cruising speed is
higher than the current speed, the
vehicle will accelerate strongly to
reach the current speed.
• By selecting the current
speed:
Press button 1 or 2 once
the desired speed has been
reached.
The new speed and “ON” will
appear in zone A.
1
II
2
3
4
5
To cancel the function
• Press on button 5.
• Select the cruise control function.
• Or stop the engine.
The speed that was chosen is no
longer memorised.
If there is a malfunction, a message is displayed accompanied by
a sound signal and lighting of the
SERVICE warning lamp.
Contact a CITROËN dealer.
Cruise control must only be used where the traffic conditions
permit driving at a constant speed.
Do not use it on congested roads or when the weather or the
road conditions are poor.
The driver still has to remain attentive and in complete control
of his vehicle.
You are recommended to keep your feet within range of the
pedals.
69
Sp e e d limit e r
II
1
2
3
A
4
5
This driving aid allows you to
choose a maximum speed that you
do not wish to exceed. This has to
be over 30 km/h (19 mph).
The speed limiter controls are
located on the steering wheel.
Note: The speed limiter information is displayed in zone A of the
instrument panel.
To select the function
Press on button 4 to select speed
limiter mode “LIMIT”.
The selection is confirmed by the
display of the function in zone A of
the instrument panel.
70
When the function is selected,
the last memorised speed and
the information “PAUSE” are displayed.
To adjust the maximum
speed
With the engine running, you can
adjust the memorised maximum
speed, displayed in zone A, by
pressing on:
• Button 1 to increase the memorised maximum speed.
• Button 2 to decrease the memorised maximum speed.
Remark: Successive presses will
modify the cruise speed in steps of
1 mph and a continuous press in
steps of 5 mph.
Activation of the function
When the desired maximum speed
is displayed, press on button 3
to activate the speed limiter. The
information “ON” disappears from
zone A.
Sp e e d limit e r
1
II
2
3
A
4
5
Suspension or resumption
of maximum speed
Press on button 3.
This action causes the information
“PAUSE” to appear in zone A of
the instrument panel.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A of the
instrument panel.
Remark: In the event of a steep
descent or under excessive acceleration, the speed limiter (which
does not act on the brakes) may
not be able to prevent the vehicle
from exceeding the programmed
speed.
The speed limiter can in no way
replace respect for speed limits or
vigilance and responsibility on the
part of the driver.
Temporary override of the
maximum speed
The accelerator pedal has an endof-travel switch. In order to exceed
the memorised maximum speed at
any time, you can press the pedal
all the way down. While the speed
is being exceeded, the speed displayed in zone A will flash. You
have only to release the accelerator pedal to return below the maximum speed, to restore the function.
Remark: the speed will also flash
if the speed limiter is not able to
prevent the vehicle from exceeding
the programmed speed (e.g. on a
steep descent or under excessive
acceleration).
To reactivate the speed limiter,
release the accelerator to slow to a
speed lower than the programmed
speed.
To cancel the function
• Press on button 5.
• Select the speed limiter function.
• Or stop the engine.
The speed that was chosen is no
longer memorised.
If there is a malfunction, a message is displayed accompanied by
a sound signal and lighting of the
SERVICE warning lamp.
Contact a CITROËN dealer.
Use of a floor mat
other than that recommended by CITROËN
may affect the normal
operation of the accelerator pedal and hamper the
operation of the speed limiter.
Floor
mats
approved
by
CITROËN are fitted with a 3rd
fixing located in the pedal
area to avoid any risk of interference with the pedals.
71
T y r e d e flation d e t e ction
Display of tyres in good
condition
II
Tyre deflation alert
A
Deflation detection
This function warns you of tyres
that are deflated or punctured.
Automatic detection
Sensors monitor the tyre pressures while driving. In the event of
an anomaly, a message will appear
on the instrument panel screen.
Driver request detection
You can check the tyre pressures
at any given moment. To do so,
press on button A (CHECK) ; the
information will be displayed on the
instrument panel screen.
72
Automatic detection
Press on Check
The system indicates to you that
the tyres are correctly inflated.
This information is only available
on the request of the driver.
Press on Check
Automatic detection:
A message indicates to you which
tyre is deflated.
Driver request detection:
The vehicle outline indicates the
deflated tyre(s).
The message is accompanied by
the SERVICE warning lamp lighting up and a beep.
Check the tyre pressures as soon
as possible.
T y r e d e flation d e t e ction
Puncture
Automatic detection
Wheel not detected
Automatic detection
Press on Check
Press on Check
Automatic detection:
A message indicates to you which
tyre is punctured.
Driver request detection:
The vehicle outline indicates the
punctured tyre(s).
The message is accompanied by
the STOP warning lamp lighting up
and a beep.
Automatic detection:
A message indicates to you which
wheel is not detected.
Driver request detection:
The vehicle outline indicates
the wheel(s) which is/are not
detected.
Note:
• If you have fitted a wheel/wheels
not equipped with tyre deflation detection (e.g. snow tyres),
contact a CITROËN dealer.
• The message is accompanied
by the SERVICE warning lamp
lighting up and a beep.
• Contact a CITROËN dealer
to have the faulty sensor(s)
replaced.
II
The deflation detection system is
a driving aid, but which does not
absolve the driver from the need to
be vigilant and responsible.
This system does not dispense with
the requirement to check the tyres
on a regular basis (see “Vehicle
identification”), to make sure that
the vehicle is behaving correctly
and to avoid premature tyre wear
arising from driving too fast etc.
Do not forget to check the pressure in the spare wheel.
Any repair or replacement of a tyre on a wheel that is equipped
with a sensor must be carried out by a CITROËN dealer.
The system may suffer from temporary interference caused
by radio transmissions on neighbouring frequencies.
73
B rak e s
G e n e ral
ABS system
II
If the parking brake is released,
the lighting of this warning lamp
along with the STOP warning
lamp indicates an insufficient level
of brake fluid or a malfunction of
the braking distribution.
It is essential to stop the vehicle.
Consult a CITROËN dealer as
soon as possible.
74
The ABS system enhances your
safety by preventing the wheels
from locking in the event of sudden braking or in conditions of
poor road adherence. It enables
you to retain control of the steering.
The functioning capability of all
the electrical components essential to the ABS is monitored electronically before and during your
journey. The ABS warning lamp
lights up when you switch on the
ignition: it should go out after a few
seconds.
If the monitoring warning lamp
does not go out, that means
that the ABS has disconnected
because there is a fault. Also, the
fact that the monitoring warning
lamp comes on during the journey shows that the ABS system is
inactive. In both cases, the normal
braking system remains efficient,
exactly as on a vehicle without
ABS. However, in order for the
security associated with the correct functioning of the ABS to be
restored, the vehicle should be
examined as soon as possible by
a CITROËN dealer.
On roads with poor adherence
(chippings, snow, ice etc.), it is
always imperative to drive with
prudence.
System of emergency
braking assistance
The emergency braking assistance
system allows you, in an emergency, to achieve the optimum
braking pressure more quickly,
thereby reducing the stopping distance. It is triggered by the speed
of your action on the brake pedal,
which reduces its resistance. To
prolong this action of the emergency braking assistance system,
simply keep your foot on the brake
pedal.
El e ctric parking brak e
Automatic operation
To start the vehicle
A
The electronic parking brake combines 2 operational modes:
• AUTOMATIC:
Automatic application when the
engine is stopped and automatic
release on use of the accelerator
(automatic operation by default).
• MANUAL:
The MANUAL application/release
of the parking brake is possible
permanently by pulling/pushing
control A.
The parking brake releases automatically
and
progressively
when you press the accelerator:
• With a manual gearbox (first
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the accelerator pedal and move off.
• With an automatic gearbox,
accelerate with the selector in
position D, M or R.
Full release of the
parking brake is
confirmed by:
• The extinction of the warning
lamp on control A and of the
instrument panel warning lamp.
• The display of the message
“Parking brake released” on the
instrument panel screen.
When stationary, with
the engine running, do
not press the accelerator pedal unnecessarily
(especially when starting the engine, including when
in neutral), as you may release
the parking brake.
To immobilise the vehicle
II
Immobilisation, engine off
With the vehicle stationary, the
parking brake is automatically
applied when the engine is
switched off.
The application of
the parking brake is
confirmed by:
• The lighting of the warning lamp
on control A and of the warning
lamp on the instrument panel.
• The display of the message
“Parking brake applied” on the
instrument panel screen.
Note: an operation sound will confirm to you the application/release
of your electronic parking brake.
Before leaving the vehicle, check that the parking brake warning lamp
on the instrument panel
is permanently lit.
Never leave a child alone inside
the vehicle with the ignition
on, as they could release the
parking brake.
75
El e ctric parking brak e
ACTIVATION / DEACTIVATION OF
THE AUTOMATIC FUNCTIONS
II
A
Immobilisation, engine running
With the engine running and the
vehicle stationary, in order to
immobilise the vehicle you need to
manually apply the parking brake
by pulling on control A.
The application of
the parking brake is
confirmed by:
• The lighting of the warning lamp
on control A and of the warning
lamp on the instrument panel.
• The display of the message
“Parking brake applied” on the
instrument panel screen.
When the driver’s door is opened,
a beep is heard and a message
displayed if the parking brake has
not been applied.
76
Before leaving the vehicle, check that the parking brake warning lamp
on the instrument panel
is permanently lit.
The automatic application when
the engine is switched off and the
automatic release when you press
the accelerator can be deactivated. Activation / deactivation is
performed using the “Main Menu”
of the instrument panel screen.
To do so, select “Vehicle parameters / Comfort / Automatic parking
brake”.
The deactivation of these
functions is confirmed by
the lighting of this warning lamp on the instrument
panel.
With the automatic functions deactivated, the application and release
of the parking brake are done manually.
The deactivation of the automatic
functions is recommended in
particularly cold conditions (ice)
and during towing (breakdown,
caravan, etc).
Manual operation
Manual application / release of the
parking brake is always possible.
To start the vehicle
With the ignition on or the engine
running, to release the parking
brake, press on the brake or accelerator pedal, push then release
control A.
Full release of the
parking brake is
confirmed by:
• The extinction of the warning
lamp on control A and of the
instrument panel warning lamp.
• The display of the message
“Parking brake released” on the
instrument panel screen.
Remark: If you push control A
without pressing the brake pedal,
the parking brake will not be
released and the message “Foot
on brake necessary” will be displayed on the instrument panel
screen.
To immobilise the vehicle
With the vehicle stationary, to
apply the parking brake whether
the engine is running or off, pull on
control A.
The application of
the parking brake
is confirmed by:
• The lighting of the warning lamp
on control A and of the warning
lamp on the instrument panel.
• The display of the message
“Parking brake applied” on the
instrument panel screen.
When the driver’s door is opened
with the engine running, a beep is
heard and a message displayed
if the parking brake has not been
applied.
El e ctric parking brak e
Sp e cial f e atur e s
Maximum application
If necessary, you can utilise maximum application of the parking
brake. It is obtained by means of
a long pull on control A, until you
see the message “Maximum parking brake application” and a beep
is heard.
Maximum application is indispensable:
• In the case of a vehicle towing a
caravan or a trailer, if the automatic functions are activated
but you are applying the parking brake manually.
• When the gradient you are
parked on is variable in its effect
(e.g. on a ferry, in a lorry, during
towing).
Note:
• In the case of towing, a loaded
vehicle or parking on a gradient,
turn the front wheels towards
the pavement and engage a
gear when you park.
• After maximum application, the
release time will be longer.
Particular situations
In certain situations (starting the
engine, etc), the parking brake can
automatically alter its force. This is
normal operation.
To advance your vehicle a few centimetres without starting the engine,
but with the ignition on, press on
the brake pedal and release the
parking brake by pushing then
releasing control A.
The full release of the parking
brake is confirmed by the extinction of the warning lamp on control A, and of the warning lamp on
the instrument panel, and by the
display of the message “Parking
brake released” on the instrument
panel screen.
If the parking brake malfunctions
while applied or if the battery
runs flat, an emergency release
is always possible (see paragraph
“Emergency unlocking”).
II
In order to guarantee its
correct operation and
therefore your safety, the
number of consecutive
applications/releases of
your parking brake is limited to
eight times.
In case of misues, you are
alerted by the message “Parking brake faulty” and the warning lamp ! which flashes (see
chapter “Operating anomalies”).
77
El e ctric parking brak e
II
A
If a failure of the ESP system is signalled by the lighting of this warning lamp,
then braking stability is not
guaranteed. In this event,
stability must be assured by the
driver by repeating alternate “pullrelease” actions on control A.
A
Dynamic emergency braking
Unlocking in emergency
In the event of a failure of the vehicle’s main braking system or in an
exceptional situation (e.g. driver
taken ill, under instruction, etc) a
continuous pull on control A will
stop the vehicle.
The electronic stability programme
(ESP) provides stability during
dynamic emergency braking.
If the dynamic emergency braking
malfunctions, one of the following
messages will be displayed on the
instrument panel screen:
• “Parking brake faulty”.
• “Parking brake control faulty”.
78
In the event of the electric parking
brake malfunctioning or the battery running flat, an emergency
manual device can be used to
unlock it.
1 Immobilise the vehicle, with the
engine running, by engaging
first gear (manual gearbox) or
position P (automatic gearbox),
then switch off the ignition and
remove the key.
Note: If it is impossible to immobilise the vehicle, do not action the
unlocking control and urgently contact a CITROËN dealer.
The dynamic emergency
braking must only be
used in exceptional circumstances.
El e ctric parking brak e
Remark: Diagnostic socket in
the armrest strengthener. Ensure
that you do not allow any dusty or
damp elements near the diagnostic socket D which is essential for
the maintenance of your vehicle.
B
2. Fetch the vehicle block located
in the boot.
3. Immobilise the vehicle by placing the block in front of or behind
one of the rear wheels.
4. Open the lower compartment
of the central armrest by pulling
upwards.
5. Ensure that the cup-holder B is
folded back.
6. Remove the rubber mat covering the base of the armrest.
7. Disengage the strap from its
location C.
8. Pull the strap to unlock the
brake. A loud click confirms that
the brake is unlocked.
D
II
C
9. Make sure that you position the
strap back in its location C. If
not, the application of the parking brake will not be possible.
Contact a CITROËN dealer.
10.Refit the rubber mat at the base
of the armrest.
11.Remove and store the block.
Note: It is necessary to
check that the parking
brake warning lamp lights
up on the instrument panel
when the parking brake is
applied.
This strap cannot apply the parking brake.
To re-engage the electric parking brake (once the malfunction or the flat battery has been
resolved), make a long pull on the
control lever A until the parking
brake warning lamp (!) flashes on
the instrument panel then make a
second long pull until this warning
lamp remains lit permanently.
The time for applying the brake
subsequent to the emergency
unlocking will be longer.
While the parking brake has
not been re-engaged (flashing then permanent lighting of
warning lamp (!) on the instrument panel), you must keep the
ignition switched off to avoid
damaging it.
79
El e ctric parking brak e
O p e rating anomali e s
II
SITUATION
Consequences
1
Electronic parking brake fault and display
of message “Parking brake faulty” and the
following warning lamps:
If the electronic parking brake fault warning lamp and the service warning lamp light up, position the vehicle in a safe location
(on flat ground, with a gear engaged).
2
Display of the messages “Parking brake
faulty” and “Anti-rollback system faulty”,
and the following warning lamps:
• The automatic functions are deactivated.
• The hill start assist is unavailable.
• The electronic parking brake is only available manually.
3
Display of the messages “Parking brake
faulty” and “Anti-rollback system faulty”,
and the following warning lamps:
• The manual release of the electronic parking brake is unavailable.
• The hill start assist is unavailable.
• The automatic functions and manual application are still available.
4
Display of the messages “Parking brake
faulty” and “Anti-rollback system faulty”,
and the following warning lamps:
and/or
80
Flashing
• The automatic functions are deactivated.
• The hill start assist is unavailable.
To apply the electronic parking brake:
1. Immobilise the vehicle and switch off the ignition.
2. Pull the control lever for at least 5 seconds or until maximum
application.
3. Switch on the ignition and check that the electronic parking
brake warning lamps are on.
Note:
• Application may take longer than in normal operation.
• If warning lamp (!) flashes or if the warning lamps do not come
on when the ignition is switched on, this method does not work.
Contact a CITROËN dealer.
To release the electronic parking brake:
1. Switch on the ignition.
2. Push the control lever and hold it for over 3 seconds.
El e ctric parking brak e
O p e rating anomali e s
5
Situation
ConsEquences
Display of message “Parking brake control
faulty - automatic mode activated” and
the following warning lamps:
• Only the functions for automatic application on switching off
the engine and automatic release on acceleration are available.
• MANUAL application/release of the electronic parking brake
and dynamic emergency braking are unavailable.
and/
or
6
7
Flashing
Display of message “Parking brake faulty”
and the following warning lamp:
Flashing
Battery fault
II
• The application of your parking brake is not guaranteed.
• Your parking brake is momentarily unavailable.
If any of these instances arises:
• Wait for about 3 minutes.
• Wait for about 3 minutes.
• After 3 minutes, if the warning lamp is still flashing, try
to reinitialise your parking brake, either by pushing and
releasing the control lever A whilst pressing the brake pedal,
or by making a long pull on the control lever A.
• The lighting of the battery warning lamp means that you
must stop the vehicle as soon as it is safe to do so. Stop and
immobilise your vehicle.
• The application of the electronic parking brake is not
guaranteed after the engine is switched off. You must therefore
apply the parking brake before switching off the engine.
If any of these instances arises, contact a CITROËN dealer as soon as possible.
81
H ill s tart a s s i s t
II
To aid starting on a gradient, your
vehicle is equipped with a system
which keeps it immobilised for a
short time (about 2 seconds), the
approximate time it takes to move
your foot from the brake pedal to
the accelerator pedal.
This function is only active when:
• The vehicle is completely stationary, with your foot on the
brake pedal.
• In particular conditions on a
slope.
• With the driver's door closed.
Note: The hill start assist function
cannot be deactivated.
The display of the message “Hill
start assist fault” indicates a malfunction of the hill start assist function.
On an ascending slope, with the
vehicle stationary, the vehicle
is held for a brief moment when
you release the brake pedal:
• If you are in first gear or neutral
with a manual gearbox.
• If you are in D or M gear with an
automatic gearbox.
On an descending slope, with the
vehicle stationary and reverse
gear engaged, the vehicle is
held for a brief moment when
you release the brake pedal.
User Precautions:
Do not leave the vehicle while it is being held in the temporary immobilisation hill start assist phase.
82
If you need to exit the vehicle with the engine running, manually apply the parking brake and
ensure that the warning lamp P (on the intrument panel) and the warning lamp P (on control A)
are permanently on.
M anual parking brak e
II
Parking brake
If the parking brake is released,
the lighting of this warning lamp
along with the STOP warning
lamp indicates an insufficient level
of brake fluid or a malfunction of
the braking distribution.
It is essential to stop the vehicle.
Consult a CITROËN dealer as
soon as possible.
The parking brake is engaged,
with the vehicle stationary, by pulling on the lever with a force appropriate to the slope.
To facilitate the action on the lever,
you are recommended to press
the brake pedal at the same time.
In all circumstances, as a precautionary measure, engage first
gear.
On steep gradients, turn the steering towards the pavement.
To release the parking brake,
press on the end of the lever whilst
pulling it then lower it fully.
The warning lamp comes on if the
parking brake is engaged or not
fully released.
83
El e ctronic s tabilit y programm e
Operation
If either of the ESP or
ASR systems is active, the
warning lamp flashes.
II
Deactivation
A
Electronic Stability
Programme (ESP) and
Traction Control (ASR)
These systems are closely associated with ABS and additional to it.
In the event of a loss of control of
the vehicle by the driver, the ESP
system acts automatically on one
or more wheels and also on the
engine to bring the vehicle back on
trajectory. The ASR system optimises traction and prevents wheel
spin by acting on the brakes of the
driving wheels as well as on the
engine. It also improves steering
stability during acceleration.
84
In exceptional conditions (vehicle
stuck in snow, soft ground, etc.)
it may prove useful to deactivate
the ESP/ASR systems to allow
the wheels to spin and thus regain
traction.
Press on control A, the warning
lamp and the light on control A
light up. The ESP/ASR systems
are no longer active.
The ESP/ASR systems will activate again:
• Automatically after the ignition has been switched off.
• Automatically when you drive
at above approx. 50 km/h
(approx. 30 mph).
• Manually with another press
on button A.
Operational anomaly
If there is a system fault, the warning lamp lights up, accompanied
by a message on the instrument
panel screen, the lighting of the
SERVICE warning lamp and a
beep.
Contact a CITROËN dealer to have
the system checked.
The ESP system offers increased
driving safety but is not in place to
encourage the driver to take additional risks or to drive at excessive
speeds.
The functioning of this system is
subject to compliance with the
manufacturer’s recommendations
on wheels (tyres and rims), brake
parts and electronic components,
as well as with the assembly and
repair procedures approved by
CITROËN.
After any collision, contact a
CITROËN dealer.
“ H y dractiv e I I I + ” s u s p e n s ion
Signalling
Normal mode, for maximum
comfort
A
“Hydractive III +” suspension automatically adjusts to road surface
conditions and driving style.
It allows you to alternate between
soft and firm suspension settings,
maximising comfort at the same
time as permanently guaranteeing
the highest level of safety. It also
automatically corrects road holding, according to the vehicle load
and driving conditions.
Also, the “Hydractive III +” suspension gives you the possibility of
choosing between two modes of
suspension.
A change of suspension mode can
be made either when the vehicle
is moving or when stationary, by
pressing on button A.
Signalling of a requested
position not authorised
II
A message is displayed on
the instrument panel.
Note: If the speed authorised for a
particular position is exceeded, the
vehicle reverts automatically to the
normal road position.
Sport mode, more suited for
a sporty style of driving
A message is displayed on
the instrument panel and
the warning lamp on button A comes on.
Note: Sport mode is retained when
you switch off the engine.
The instrument panel screen
temporarily displays a message
indicating that this position is not
authorised.
The vehicle remains in the authorised position and the instrument
panel screen indicates this position
to you.
Note: Automatic variation of
ground clearance
• If
your
speed
exceeds
110 km/h (approx. 70 mph),
on a good road surface,
ground clearance is lowered.
The vehicle returns to its
normal position if the road
surface deteriorates or if your
speed is lower than 90 km/h
(approx. 55 mph)
• At low or medium speed, if the
road surface is poor, ground
clearance is increased. The
vehicle returns to its normal
position as soon as conditions
allow.
85
“ H y dractiv e I I I + ” s u s p e n s ion
Viewing of the position of
the vehicle
Once the adjustment has been
made, a message is displayed on
the instrument panel screen.
II
Normal road position
Position changes may only be
made when the engine is running.
Adjustable
ground
clearance
responds to all types of situation.
Apart from a few specific situations, driving in the normal road
position is imperative.
Note: If the speed authorised for a
particular position is exceeded, the
vehicle reverts automatically to the
normal road position.
Maximum height
Changing a wheel (Not possible if
speed > 10 km/h).
To change the position
Press once on one of the adjustment controls. The change in position is indicated by a message on
the instrument panel screen:
Minimum height
Intermediate position
For an increased ground clearance
(Not possible if speed > 40 km/h).
For use on difficult roads when
travelling at reduced speed, as
well as on carpark ramps.
86
To facilitate loading or unloading
the vehicle.
For workshop inspections.
Not to be used in normal driving
(Not possible if speed > 10 km/h).
or your safety if you are
F
operating underneath
the vehicle, it is obligatory to support the vehicle with axle stands.
L an e D e partur e W arning S y s t e m
Activation/Deactivation
A
A press on button A activates the
function, the warning lamp on the
button lights up.
A second press on button A deactivates the function, the warning
lamp on the button goes out.
When you start the engine, the
mode
(activated/deactivated)
selected when you stopped the
engine is retained.
Operation
This driving assistance device
warns you when you unwittingly
cross a lane marking (either a continuous or a dotted line on the road
surface). It is designed for use on
motorways and dual carriageways,
operating only above speeds of
approx. 80 km/h (50 mph)..
Above a speed of around 80 km/
h, if you cross a lane marking, you
are alerted to this by a vibration
within the cushion of your seat:
• On the right hand side if you
cross a lane marking to the
right.
• On the left hand side if you
cross a lane marking to the
left.
The system does not alert you if
one of your direction indicators is
operating and for approx. 20 seconds after the direction indicator
has stopped.
Remarks:
This system is designed to identify
traffic lane markings.
In certain cases it may trigger an
alert that is unnecessary, for example if the vehicle passes over a
directional arrow or some unusual
road marking.
The system may be affected temporarily by conditions external to
the vehicle:
• Detection of lane markings
made difficult by:
- Markings being worn.
- Insufficient contrast with the
general road surface.
• Sensors being negated by:
- Driving in snow or heavy rain.
- Driving on roads that are
covered with mud or water
puddles.
If there is prolonged interference,
contact a CITROËN dealer.
II
The driver still has to
remain attentive and
in complete control of
his vehicle.
87
Parking a s s i s tanc e
II
88
Front
Rear
Proximity sensors are located in
the front and rear bumpers of
your vehicle.
When manoeuvring whether forwards or in reverse, at a speed
below approximately 10 km/h
(6 mph), they warn you of the presence of any obstacle located within
their detection zone, by means of:
• A sound signal emitted by the
front or rear loudspeakers.
• Display of the outline of your
vehicle with shading corresponding to the area where an
obstacle is detected.
As the vehicle approaches the
obstacle, the sound signal tells you
the position of the obstacle according to whether the sound is coming
from the front LH or RH or the rear
LH or RH loudspeakers.
Note: The sound volume of your
audio equipment reduces automatically when a signal is being
emitted.
As the vehicle approaches the
obstacle, the sound signal becomes
more and more urgent and the
shaded areas are displayed closer
and closer to the vehicle.
When the obstacle is
less than approximately
25 cms from your vehicle,
the sound signal becomes
continuous and a warning
panel appears on the display.
Parking a s s i s tanc e
Operation
A
Activation/Deactivation
You can activate/deactivate the
parking assistance by pressing
button A. When the parking assistance is inactive, the warning lamp
on button A is lit up.
Activation/deactivation of the parking assistance is memorised when
you stop the vehicle.
Remark: If you are towing with
a towing device not approved
by CITROËN, it is necessary to
deactivate parking assistance by
pressing on button A. The warning lamp on the button lights up.
When you engage reverse gear,
a sound signal confirms to you
that the system is active. The outline of your vehicle appears on the
screen. Any obstacles located to
the rear or to the front of the vehicle can be detected.
When going forward and at a
speed below approx. 10 km/h
(6 mph), whether in neutral or in
gear, the outline of the vehicle
appears on the display as soon
as an obstacle is detected in front
of the vehicle. Obstacles located
in front of the vehicle will be
detected.
Remarks:
• The proximity sensors cannot
detect objects that are immediately under or over the bumpers.
• A thin object such as a spike,
a bollard or similar, can only
be detected at the start of the
manœuvre but not when the
vehicle arrives close up to it.
• In poor weather or in winter, you
need to ensure that the sensors
are not covered with mud or
with ice or snow.
II
89
Parking s pac e s e n s or
II
A
The “Parking Space Sensor” function assists you in finding a parking
space. It measures the size of the
space and gives you information
on:
• The possibility of parking in a
free space, depending on the
dimensions of your vehicle and
the space needed to manoeuvre into it.
• The level of difficulty of the
manoeuvre to be carried out.
Note: The system does not measure spaces which are clearly much
smaller or larger than the size of
the vehicle.
90
Parking Space Sensor
warning lamp
The warning lamp is located on
button A. It has 3 different statuses:
• Off:
the
function
is
not
selected.
• Permanently on: the function
is selected but the measuring
conditions are not met (direction indicator not on, vehicle
speed too high) or the measuring phase has finished.
• Flashing: measuring is in
progress.
Note: During measuring, the message “Measuring in progress Max speed 20km/h /12 mph” is
displayed on the instrument panel
screen.
You can select the “Parking Space
Sensor” function by pressing button A.
The fixed lighting of the warning
lamp indicates that this function is
selected.
Parking s pac e s e n s or
Operation
You have identified a parking space:
1. Press button A to select the
function.
2. Activate the relevant direction
indicator.
The system will measure the parking space:
The following messages may be
displayed:
Parking possible
Parking difficult
3. During measuring, go forwards the length of the space,
at a speed less than 20 km/h
(12 mph), to prepare for your
manoeuvre.
4. The system indicates to you the
level of difficulty of the manoeuvre via a message on the instrument panel screen accompanied by a gong.
5. Depending on the message
issued by the system, you may
or may not be able to perform
the manoeuvre.
Parking not advised
Note: The function deactivates
itself automatically:
• When you engage reverse
gear.
• When you switch off the ignition.
• If measuring is not requested
in the 5 minutes after selecting
the function.
• If the vehicle speed exceeds the
threshold of 70 km/h (approx.
45 mph) for one minute.
Warning: If the distance between
your vehicle and the parking space
is over approx. 1.50 m, the system
may not be able to measure the
space.
II
Remarks:
• The function remains available
after each measurement and
can therefore measure several
spaces in succession.
• In poor weather or in winter, you
need to ensure that the sensors
are not covered with mud or
with ice or snow.
• If the Parking Space Sensor
function is selected, the Parking Assistance function is deactivated.
In the event of a malfunction, consult a CITROËN dealer.
91
A cc e s s
III
A
Locking/unlocking from the
inside
With the doors and the boot closed,
pressing button A allows you to
control the electric central locking
and unlocking.
It is still possible to open the doors
from the inside.
If one of the doors is open or not
properly closed, central locking will
not work.
92
The warning lamp associated with
the control A signals 3 statuses:
• lt flashes when the ignition key
is in the stop position or when
the key is not detected and the
doors are locked.
• It lights up when the vehicle is locked with the ignition
switched on.
• It goes out when the doors are
not locked.
Note: Control A is inactive if the
vehicle has been locked using the
remote control or the key.
Anti-theft protection
On starting the vehicle, the system
automatically locks the doors as
soon as you reach approximately
10 km/h.
Note: If a door is opened, this will
automatically lock itself again when
the vehicle reaches approximately
10 km/h (6 mph).
Activation/Deactivation of
the anti-intrusion protection
After switching on the ignition,
make a long press on the central
unlocking control until a message
is displayed and a beep is heard.
Selection of doors / boot
After having selected “Plip action /
Driver” in the “Vehicle parameters /
Comfort” menu of the instrument
panel screen.
Pressing
the
remote
control
unlocks the passenger door.
A 2nd successive press unlocks all
of the doors and the boot.
If you decide to drive with the doors locked, remember that
in the event of an accident this renders access more difficult for the emergency services.
A cc e s s
III
B
Manual operation
(Emergency mode)
Driver's door
Insert the key into the lock to lock/
unlock the door.
Passenger doors
It is possible to lock the passenger
doors in the event of an electrical
fault by using control B on each
door:
• With the door open, unclip the
plastic cover.
• Insert an object, such as the
end of a key, into the cavity and
turn.
• Replace the plastic cover.
• Close the door.
After this operation, normal operation resumes using the central
unlocking control (inside the vehicle), the remote control or the key.
C
BOOT (SALOON)
Opening
Press upwards on lever C and lift
up the boot.
Locking/unlocking
With the vehicle stationary, this is
carried out using:
• The remote control.
• The key in a door lock.
• The interior central locking/
unlocking control.
The boot automatically locks when
the vehicle is moving at a speed
of over 10 km/h (6 mph), even if
automatic central locking is deactivated. It is unlocked when a door
is opened or when the central locking button is pressed (speed lower
than 10 km/h (6mph)).
D
Emergency unlocking
If there is a problem with opening
the boot or if the battery is flat:
• Fold down the rear seats to
access the boot from inside the
vehicle.
• Get into the boot.
• From inside the boot, move
yourself towards the rear of the
vehicle.
• Insert a screwdriver into hole D
of the lock.
• To unlock, push the white component (located inside the lock)
to the left.
93
A C C ESS
Interrupting the opening/
closing of the tailgate
III
B
A
TAILGATE (TOURER)
Manual opening
Press upwards on lever A and lift
up the tailgate.
Electric opening
Press upwards on lever A, or press
button B of the remote control.
Locking/unlocking
With the vehicle stationary, this is
carried out using:
• The remote control.
• The key in a door lock.
• The interior central locking/
unlocking control.
94
In order to avoid risk of
injury, make sure that
no-one is in the vicinity of the boot when
carrying out an electric
opening manoeuvre.
B
C
The tailgate automatically locks
when the vehicle is moving at a
speed of over 10 km/h (6 mph),
even if automatic central locking
is deactivated. It is unlocked when
a door is opened or when the
central locking button is pressed
(at a speed of less than 10 km/h
(6 mph)).
Manual closing
Lower the tailgate using the interior
handle B.
Electric closing
Press the push-button C to close
the tailgate.
Note : do not interrupt the closing
of the tailgate ; if any obstacle prevents it closing, the operation will
stop and the tailgate will automatically rise by a few centimetres.
When the tailgate is being closed
electrically, you can interrupt its
movement at any point by pressing
the tailgate push-button C.
Note : After an interruption, the
tailgate is held electrically in an
intermediate position for about
10 minutes. After this period, the
system automatically goes to
standby and releases the tailgate.
To exit the intermediate position
mode, close the tailgate electrically
or manually.
Memorisation of an
intermediate position
You can store an opening angle for
the tailgate:
• Manually or automatically move
the tailgate to the required position.
• Make a long press on the pushbutton C. The system emits a
beep.
• Release the push-button C.
Cancelling the memorisation
With the tailgate in the intermediate position, you can cancel the
stored position :
• Make a long press on the pushbutton C. The system emits a
beep.
• Release the push-button C. The
tailgate reverts to the fully open
position.
A utomatic air conditioning
G e n e ral
III
A
B
C
D
A.Sunlight sensor.
B.Soft air conditioning diffusion grille.
The soft diffusion grille located in the centre of the dashboard provides an optimum air
distribution for the front seats.
This device eliminates unpleasant air currents whilst maintaining an optimum temperature in the passenger compartment.
To open the soft air diffusion grille, move the control knob upwards.
To close the soft air diffusion grille, move the control knob all the way down.
In very hot weather, to improve the central and lateral ventilation, closing off the soft
diffusion air conditioning is recommended.
C.Air conditioned glovebox.
D.Rear passenger air vents.
95
A utomatic air conditioning
G e n e ral
III
96
You are advised to use the automatic air conditioning regulation.
This automatically regulates the
following functions for maximum
comfort : air flow, passenger compartment temperature, and air distribution, using different sensors
(external temperature, sunlight).
This avoids the need to alter any of
the settings, with the exception of
the temperature displayed.
Take care not to obstruct the sunlight sensor A.
Provided you retain automatic
mode (by pressing button “AUTO”)
and all the air vents are open, you
will maintain an optimum comfort
level, also removing humidity and
misting, whatever the ambient climatic conditions.
The temperature inside the cabin
cannot be lower than the temperature outside if the air conditioning
is not operating.
To be effective, the air conditioning
should only be used with the windows closed. If after a lengthy stop
in bright sunlight the interior temperature is excessive, air the passenger compartment by opening
the windows for a few moments,
then close them again.
To ensure the correct operation of
the air conditioning system, it is
essential to operate the air conditioning at least once a month.
The air conditioning operates by
using power from the engine. This
results in a slight increase in fuel
consumption.
In certain extreme operating conditions (e.g. carrying a full load up
a steep gradient in high temperatures), the switching off of the air
conditioning allows more power
to be transferred to the engine,
thereby increasing the towing
capacity.
Air inlet
Check that the exterior grille for the
air inlet, at the bottom of the windscreen, is clean and free of dead
leaves, snow, etc.
If washing the vehicle with a high
pressure jet, avoid targeting the air
inlet zone.
Air circulation
For your comfort we advise you to
maintain a proper distribution of air
within the cabin, both at the front
and at the rear.
To obtain an even distribution of
air, ensure that you do not obstruct
the external air inlet grille located
at the base of the windscreen, the
air vents, the air outlets on the floor
underneath the front seats, and
the air extractor located behind the
flaps in the boot.
The front and rear air vents are fitted with control knobs which allow
you to control and direct the air
flow. It is recommended to keep all
the air vents open.
Dust/pollen filter
There is a filter for excluding pollen
and dust.
This filter has to be changed according to the vehicle maintenance schedule. See “Maintenance Guide”.
A utomatic air conditioning
MONOZONE
The monozone system regulates
the temperature, air distribution
and air flow for the whole of the
passenger compartment.
1 Automatic operation
2 Temperature adjustment
3 Adjusting the air distribution
4 Activation/deactivation of air
conditioning
5 Adjusting the air flow
6 Front demisting - deicing
7 Rear demisting - deicing
8 Air recirculation – Entry of air
from outside
9 Display
1.Automatic operation
This is the normal
operating mode for
the system. Depending on the level of
A
comfort chosen, a
press on this button,
confirmed by light A coming on,
allows all of the following functions
to be automatically and simultaneously controlled:
• Air flow.
• Cabin temperature.
• Air distribution.
• Air inlet.
• Air conditioning.
1
8
2
8
3
8
4
8
9
8
7
5
8
6
It is recommended to keep all the
air vents open.
You can change to manual mode
by pressing on any of the buttons,
except button 2.
The light A goes out.
Operating the air conditioning system on “AUTO” guarantees good
ventilation inside the cabin.
Note: The value indicated on the
display corresponds to a comfort
level and not to a temperature in
Celsius or Fahrenheit.
2. Temperature adjustment
Manual mode
Turn
control 2
to
change the temperature:
• Clockwise to
A
increase the temperature.
• Anti-clockwise to reduce the
temperature.
• The chosen temperature is
displayed.
An adjustment around 21 will give
you the optimum comfort level.
However, depending on your preferences anywhere between 18 and
24 is quite usual.
III
One or more functions can be
adjusted manually, while still retaining the other functions in automatic
mode.
Press one of the buttons, except
the temperature adjustment 2. The
light A goes out.
Changing to manual mode may
result in a decrease in comfort
level (temperature, humidity, smell,
misting) and is not advised for optimum comfort.
To return to “AUTO” mode, press
button 1. Light A comes on.
97
A utomatic air conditioning
MONOZONE
III
3.Adjusting the air
distribution
Press on buttons 3 to
change the air flow distribution. The symbol
(arrows) corresponding
to the chosen distribution lights up:
• Windscreen and front windows.
• Front air vents (central, side
and soft diffusion grille if open)
and rear air vents.
• Front and rear footwells.
Note: You cannot select distribution to the windscreen/front windows and to the front/rear air vents
at the same time.
4.Air conditioning
Air conditioning only works with
the engine running. The air blower
button
(air
flow
adjustment)
must be activated to obtain air
conditioning.
B
98
Press
on
button 4.
Light B comes on.
To function efficiently, air
conditioning
should
be used with the windows closed.
5. Adjusting the air flow
The air flow can only
be adjusted with the
engine running.
Turn control 5:
• Clockwise to increase the air
flow.
• Anti-clockwise to reduce the air
flow.
The level of air flow is indicated on
the control panel display 9 by the
progressive filling of the bars.
By reducing the air flow to its
minimum setting, the air conditioning system switches itself
off (OFF).
To prevent misting and poor air
quality in the passenger compartment, take care to maintain a sufficient flow of air.
6. Front demisting - deicing
In some cases, “AUTO”
mode may not be sufficient to demist or
defrost the windows
(e.g. humidity, several
passengers, frost).
Press button 6 for rapid clear windows.
The warning lamp comes on. This
system controls air conditioning,
temperature and air flow/entry. It
distributes ventilation towards the
windscreen and the front windows.
You can manually exit “Demisting”
mode. This mode should be cancelled as soon as possible to allow
the redistribution of air in the passenger compartment.
A press on the 1 button returns you
to “AUTO” mode.
7.Rear demisting - deicing
Press button 7, with the
engine running, to start a
rapid deicing or demisting of the rear screen
and rear view mirrors.
The warning lamp comes on.
This mode automatically stops
depending on the outside temperature. It can be interrupted by a further press on button 7 or by stopping the engine.
In the latter case, demisting
will resume when the engine is
switched on again.
Note: The heated rear screen
operates independently of the
automatic air conditioning.
A utomatic air conditioning
MONOZONE
8.Air recirculation – Entry
of air from outside
This button activates
the recirculation of air in
the passenger compartment.
Press button 8 to switch
off the entry of air from outside.
The warning lamp comes on.
Whilst retaining the other settings,
this position allows the driver at
any moment to exclude unpleasant
smells or smoke/emissions coming
from outside.
This mode should be cancelled
as soon as possible to allow the
redistribution of air in the passenger compartment.
Remarks:
• When starting from cold, in
order to prevent unwanted cold
air, the air flow will increase only
gradually to its optimum level.
• If you enter the vehicle after a
fairly prolonged stop and the
temperature inside the vehicle
is far from comfortable, it serves
no purpose to modify the temperature that is displayed as an
attempt to go immediately to
the desired comfort level. The
system automatically uses all
of its power to compensate the
temperature gap as quickly as
possible.
• Water arising from the condensation in the air conditioning
drains out through a hole provided for this purpose ; a pool
of water may thus form underneath the vehicle when stationary.
• Whatever the time of year, even
in cool weather the air conditioning is useful in removing humidity and misting. Avoid driving for
too long with air conditioning
deactivated.
III
99
A utomatic air conditioning
D ual - zon e
III
The dual-zone system regulates
the temperature and air distribution
for the drivers's side and the passenger's side independently. The
air flow is common to both sides.
1aDriver's side automatic operation
1bPassenger's side automatic
operation
2aAdjustment of temperature on
driver's side
2bAdjustment of temperature on
passenger's side
3aAdjustment of air distribution
on driver's side
3bAdjustment of air distribution
on passenger's side
4aDriver's side display
4bPassenger's side display
5 Adjusting the air flow
6 Activation/deactivation of air
conditioning
7 Air recirculation – Entry of air
from outside
8 Rear demisting - deicing
9 Front demisting - deicing
100
1a
8
2a
3a
4a
9
5
8
8
1a-1b.Automatic operation
This is the normal operating mode for the system. Depending on the
level of comfort chosen,
A
a press on this button,
confirmed by light A
coming on, allows all of the following functions to be automatically
and simultaneously controlled:
• Air flow.
• Cabin temperature.
• Air distribution.
• Air conditioning.
• Automatic air recirculation.
It is recommended to keep all
the air vents open. Just by pressing any of the buttons, except for
temperature 1a and 1b, you can
change to manual mode. The
light A goes out.
6
8
4b
8
3b
2b
1b
8
7
2a-2b. Temperature
adjustment
A
Turn control 2a to change the driver's side temperature and control 2b to change the passenger's
side temperature:
• Clockwise to increase the temperature.
• Anti-clockwise to reduce the
temperature.
The chosen temperature is displayed.
An adjustment around 21 will give
you the optimum comfort level.
However, depending on your preferences anywhere between 18
and 24 is quite usual.
A utomatic air conditioning
D ual - zon e
Operating the air conditioning system on “AUTO” guarantees good
ventilation inside the cabin.
Note: The value indicated on the
display corresponds to a comfort
level and not to a temperature in
Celsius or Fahrenheit.
Manual mode
One or more functions can be
adjusted manually, while still retaining the other functions in automatic
mode.
Press on any of the buttons, except
for temperature 2a and 2b. Lights A
on buttons “AUTO” go out.
Changing to manual mode may
result in a decrease in comfort
level (temperature, humidity, smell,
misting) and is not advised for optimum comfort.
To return to “AUTO” mode, press
on buttons 1a and 1b. Lights A
come on.
- Press button 3b to change the
passenger's side air flow distribution.
The symbol (arrows) corresponding to the chosen distribution lights
up:
• Windscreen and front windows.
• Front air vents (central, side
and soft diffusion grille if open)
and rear air vents.
• Front and rear footwells.
Note: You cannot select distribution to the windscreen/front windows and to the front/rear air vents
at the same time.
4. Adjusting the air flow
The air flow can only be adjusted
with the engine running.
To adjust the air flow, press button:
to increase the air flow
to reduce the air flow
3a-3b.Adjusting the air
distribution
- Press button 3a to
change the
driver's side air
flow distribution.
The air flow level is indicated by the
progressive lighting of the ventilator
blades.
By reducing the air flow to its minimum setting, the air conditioning
system switches itself off (OFF).
To prevent misting and poor air quality in the passenger compartment, take
care to maintain a sufficient flow of air.
5. Air conditioning
Air conditioning only works
with the engine running.
The air blower button (air
flow
adjustment)
must
be activated to obtain air
conditioning.
Press on button 6. The warning lamp
comes on.
To function efficiently, air conditioning
should be used with the windows
closed.
III
6.Air recirculation – Entry
of air from outside
This button activates
the recirculation of air in
the passenger compartment and can function
automatically.
Entry of air in automatic
anti-pollution mode
activated by default, in
automatic comfort regulation.
Automatic mode uses an air quality sensor. This analyses the air and
isolates the passenger compartment
from the exterior, as soon as it detects
the presence of pollutants. In this case,
it automatically activates recirculation
of passenger compartment air.
Remark: this function cannot detect
and therefore protect the passenger
compartment from bad smells not
linked to pollutants. It is not active
when the outside temperature is
below +5°C in order to protect against
the risk of misting.
101
A utomatic air conditioning
D ual - zon e
III
Switching off the entry
of air
Press button 6 to switch
off the entry of air from
outside.
Whilst retaining the other settings,
this position allows the driver at
any moment to exclude unpleasant smells or smoke/emissions
coming from outside.
This mode should be cancelled
as soon as possible to allow the
redistribution of air in the passenger compartment.
Entry of air from outside
Press once on button 6 to
return to the original status
(Entry of air from outside).
7.Rear demisting - deicing
102
Press button 7, with
the engine running, to
start a rapid deicing or
demisting of the rear
screen and rear view
mirrors. The warning lamp comes
on.
This mode automatically stops
depending on the outside temperature. It can be interrupted by a further press on button 7 or by stopping the engine.
In the latter case, demisting
will resume when the engine is
switched on again.
Note: The heated rear screen
operates independently of the
automatic air conditioning.
8. Front demisting - deicing
In some cases, “AUTO”
mode may not be sufficient to demist or
defrost the windows
(e.g. humidity, several
passengers, frost).
Press button 8 for rapid clear windows. The warning lamp comes
on. This system controls air conditioning, temperature and air
flow/entry. It distributes ventilation
towards the windscreen and the
front windows.
You can manually exit “Demisting”
mode. This mode should be cancelled as soon as possible to allow
the redistribution of air in the passenger compartment.
A press on either of the buttons 1a
or 1b allows you to return to
“AUTO” mode.
Remarks:
• When starting from cold, in
order to prevent unwanted cold
air, the air flow will increase only
gradually to its optimum level.
• If you enter the vehicle after a
fairly prolonged stop and the
temperature inside the vehicle
is far from comfortable, it serves
no purpose to modify the temperature that is displayed as an
attempt to go immediately to the
desired comfort level. The system automatically uses all of its
power to compensate the temperature gap as quickly as possible.
• Water arising from the condensation in the air conditioning
drains out through a hole provided for this purpose ; a pool
of water may thus form underneath the vehicle when stationary.
• Whatever the time of year, even
in cool weather the air conditioning is useful in removing humidity and misting. Avoid driving for
too long with air conditioning
deactivated.
programmablE H E AT I N G
(DEPENDING ON COUNTRY)
8
7
1
III
2
1
9
3
6
5
4
With the engine off, programmable
heating preheats the coolant circuit in order to optimise the engine
operating temperature prior to
starting.
The programmable heating system can be started immediately or
delayed thanks to its programming
function.
With the engine idle or the
vehicle stationary, it is normal to hear a high-pitched
whistling noise and to
notice some smoke / emissions.
Digital programmer
The heating system’s programmer
is located on the right-hand side of
the dashboard.
1. Time or remaining functioning
time.
2. Increase (time).
3. Select programme.
4. Programme number selected.
5. Immediate start-up of heating.
6. Time adjustment and reading
warning lamp.
7. Reduce (time).
8. Heating mode warning lamp.
9 Programmable heating system
warning lamp.
• LED lit : Activated.
• LED off : Deactivated.
Immediate start-up
Press button 5.
The screen displays a default
duration of 60 minutes, you are
advised to adjust this to a duration of
30 minutes maximum (see section
“ adjusting the operating duration ”).
The warning lamp 8 lights up and
remains lit for the whole duration of
the system’s operation. The duration
of the system’s operation disappears
after 10 seconds.
Stopping the heating
Press button 5.
The warning lamp 8 and the screen
go out.
103
programmablE H E AT I N G
2
2
III
7
6
3
Delayed start-up
Reading the time
Note : Before programming the
delayed start-up of the heating,
you must ensure that the clock is
set to the correct time.
Press button 2 or button 7 to display the time.
When the heating mode is activated, the remaining operating time
is displayed in place of the time.
Setting the time
Programming the start-up time
Hold button 3 down and press button 2 or button 7. Release button 3,
the time is displayed and symbol 6
flashes.
Use the two adjustment buttons 2
(to go forward) or 7 (to go back)
until the correct time is displayed.
Holding these buttons down will
make the numbers displayed scroll
more quickly.
104
A
Start-up may be programmed
between 1 minute and 24 hours in
advance.
You can store up to 3 different startup times, but programme only 1
delayed start-up time.
Factory settings A :
• Time 1 : 06:00.
• Time 2 : 16:00.
• Time 3 : 22:00.
Note : The factory settings are
replaced once you adjust them.
The programmed times are stored
until they are re-programmed.
7
3
Press button 3 then buttons 2 or 7
in the next 10 seconds, until the
desired start-up time is displayed.
Note : if you wish to recall the other
stored times, press several times on
button 3 in the next 10 seconds until
the desired programme number is
displayed.
Cancelling the programmed time
To cancel the programmed start-up
time, press briefly on button 3.
Note : In the event of a battery
failure, the factory settings are
restored.
programmablE H E AT I N G
8
4
3
Selection and activation of a
programmed time
Press button 3 until the programme
number corresponding to the
required programmed time is displayed. The chosen pre-selected
time is automatically activated
after 10 seconds if no other buttons have been pressed.
To confirm that the mode is activated, symbols 4 and 8 flash until
the heating starts up.
When the heating starts up, the
warning lamp 9 lights up on the
dashboard and the programmer
screen.
7
2
6
III
3
Adjusting the operating
duration
Press button 3 and hold it down.
Press button 2 or 7 at the same
time. Release button 3. The time
and symbol 6 are displayed.
Press again on button 3 and hold
it down. Press button 2 or 7 at the
same time. Release button 3. The
operating duration and symbol 8 is
displayed.
Adjust the operating duration with
button 2 or 7.
Note : The operating duration is
memorised when the time indicated
disappears or by pressing button 3.
Adjusting the remaining
operating duration
Note :
• The pre-selected start-up time
can be modified or cancelled by
following the instructions previously given above.
• In the event of a battery disconnection, the programmer must
be re-set (hours, minutes etc.)
When heating mode is activated,
the remaining operating time can
be modified within the range of 10
to 60 minutes using buttons 2 or 7.
Always switch off the additional
heating when filling up with
fuel, to prevent any risk of fire
or explosion.
To avoid any risk of intoxication or asphyxiation, the additional heating must not be used,
even for short periods, in an
enclosed area such as a garage
or workshop not equipped with
a system for the extraction of
exhaust gases.
Do not park the vehicle over
inflammable materials (e.g. dry
grass, dead leaves or paper) as
this could present a fire risk.
The programmable heating system is supplied by the vehicle’s
fuel tank. Before use, ensure
that the remaining fuel level is
sufficient. If you are using the
reserve fuel tank, we strongly
advise you not to use the programmable heating system.
105
R e ar s e at s
III
A
Rear head restraints
The rear head restraints have two
positions:
• A stowed position for when the
seat is not occupied.
• A deployed position for safety
of passengers, locking into
place including for a forwardfacing child seat.
To lower them, press on the unlocking control A.
To remove them, pull upwards as
far as possible and press on the
unlocking control A.
For your safety, do not
drive with the head
restraints removed;
these must be in place,
correctly adjusted.
106
Flap for transport of long
objects
A flap in the backrest, located to
the rear of the armrest, facilitates
the carrying of long objects.
Ensure that the objects are well
secured and that they do not
impede the operation of the gear
lever.
R e ar s e at s
• Pull control 3 forwards to
unlock the backrest 2.
• Move the backrest 2.
1
2
Folding benchseat
The benchseat can either be totally
or partially folded (1/3-2/3).
To fold the rear left or right hand
seat, always start with the seat
cushion, never the backrest (risk of
damage):
• Move the front seat(s) forward
if necessary.
• Place the head restraints in
their lowest position or remove
them if necessary.
Check that the seat belt is correctly
positioned by the side of the backrest.
Ensure that you fasten the side
seat belts into their buckles (the
central seat belt should not be fastened).
• Lift up the front of seat cushion 1.
• Move seat cushion 1 against
the front seat(s).
Pinch the seat cushion fixings to
remove them from their fasteners.
When repositioning:
• Fold the backrest 2 back up
and lock it into place (the red
light on button 3 should go
out).
• Fold up the seat cushion 1.
• Replace the head restraints if
you had removed them.
Ensure that the front and rear backrests are correctly locked in place.
III
3
The red light on button 3 should no
longer be visible - if not, push the
seat all the way back.
Be careful not to trap the seat belt and to correctly buckle
each belt, before each operation of moving the backrest. This
operation allows you to fold the backrests back up with their
seat belts and buckles ready for use by rear passengers.
107
A irbag s
Reactivating the front
passenger's airbag
III
A
Front passenger's airbag
deactivation
In order to be able to use a rearfacing child seat in the front passenger's seat position, it is imperative to deactivate the passenger's
airbag.
For that:
• With the ignition switched off,
insert the key into the switch A.
• Turn the key to the “OFF” position, the passenger's airbag is
deactivated.
With the ignition on, the front
passenger's airbag deactivation warning lamp lights up on
the roof console display.
108
Do not forget to reactivate
the function.
For that:
• With the ignition switched
off, insert the key into the
switch A.
• Turn the key to the “ON” position, the airbag is activated.
When the ignition is switched
on, the warning lamp on the
roof console display lights up
for a few seconds.
Note: It is compulsory to wear the
seat belt.
Never deactivate the passenger's airbag when a passenger is
present (unless a child in a rearfacing child seat).
Front /
lateral airbag fault
This message is displayed on the
instrument panel if there a fault
with the front / lateral airbags.
In the front passenger's seat position, it is imperative to
deactivate the front passenger's airbag if you are installing a
“rear-facing” child seat there. Otherwise the child risks being
killed or seriously injured should the airbag deploy.
C hild s af e t y
A
Electric operation
The child safety function is activated by pressing button A. This
deactivates the controls in the rear
of the vehicle, both for the rear
windows and for opening the rear
doors from the inside.
It is still possible to open the doors
from the outside and to operate the
electric windows from the front of
the vehicle.
Note:
• The activation of this function
is confirmed by a message on
the instrument panel screen
and the light on button A coming on.
• If the light on button A flashes,
the doors have not been closed
properly.
The status of this function is memorised when the ignition is switched
off.
The electric child safety is automatically deactivated in the event
of a serious accident (e.g. triggering of an airbag).
Any variance in the behaviour of the light on button A (e.g.
flashing when the doors are closed, going out whilst the
function is activated...) indicates a malfunction of the child
safety function. Contact a CITROËN dealer.
III
109
C hild r e s traint s
CHILD SEATS SECURED BY MEANS OF THE VEHICLE SEAT BELT
III
In conformity with Directive 2005/40, the table tells you to what extent each
of the seat positions in your vehicle may take a child seat that is secured by
means of the vehicle seat belt and approved as “Universal” depending on
the weight of the child.
Consult “User Precautions”, chapter on “Child Safety” at the end of
this handbook, in order to ensure that you are installing your child in
conditions of maximum safety.
A
A
Weight of child
Up to 10 kg
and up to 13 kg
(groups 0 and 0+)
9 - 18 kg
(group 1)
15 - 25 kg
(group 2)
22 - 36 kg
(group 3)
U
U
U
U
Lateral rear
U
U
U
U
Central rear
U
U
U
U
Seat position(s)
Front passenger
(a)
U :Seat position suitable for installation of universally approved rear-facing
and/or front-facing child seat.
(a) : Consult the current legislation for your country before driving with your
child in this seat.
In the front passenger's seat position, it is imperative to
deactivate the front passenger's airbag if you are installing a
“rear-facing” child seat there. Otherwise the child risks being
killed or seriously injured should the airbag deploy.
Take care to comply with the fitting instructions given in the
child seat manufacturer’s installation guide.
110
ISOFIX child seats
ISOFIX anchoring points and
the ISOFIX fastening system
Your vehicle is ISOFIX approved
in conformance with European
law ECE 14-06. The lateral rear
seats and the front passenger seat
are fitted with regulation ISOFIX
anchoring points.
Incorrect installation of a child
seat in a vehicle compromises
protection of the child in the event
of a collision. The ISOFIX system enables you to minimise the
risks posed by incorrect fitting.
The ISOFIX fastening system gives
you a convenient, strong and reliable fitting for a child seat in your
vehicle.
C hild r e s traint s
D
C
C
B
E
The ISOFIX fastening
system
Front (saloon and Tourer)
The ISOFIX system is made up
of 3 rings for the front passenger
seat:
• 2 rings A located between the
backrest and the seat cushion,
with the ISOFIX logo.
• A third ring B fixed in the lower
section of the rear of the backrest.
Rear (saloon)
The ISOFIX system is made up of
3 rings for each side rear seat :
• 2 lower rings C located between
the backrest and the seat cushion,
with the ISOFIX logo.
• One top ring D fixed on the rear
shelf, concealed under a flap with
the TOP TETHER logo behind
the head restraint.
Rear (Tourer)
The ISOFIX system is made up of
3 rings for each side rear seat :
• 2 lower rings C located between
the backrest and the seat cushion.
They are approximately 28 cm
apart and have the ISOFIX logo.
• One top ring E, concealed under
a flap with the TOP TETHER
logo.
The ISOFIX child seat
fastening system
ISOFIX child seats have 2 latches
which are easy to anchor on the 2
lower rings A or C.
Some ISOFIX child seats also
have an additional belt which is
attached to the upper ISOFIX
ring D (saloon) or E (Tourer) of
the side rear seats.
To attach the top belt, raise the
head restraint of the vehicle seat,
then pass the buckle between the
rods. Next fix the buckle on the
top belt D or E and tension the top
belt.
This fixing system is intended for
children weighing up to 18 kg.
The ISOFIX child seats which can
be installed in your vehicle are
indicated in the table on the next
page.
III
111
C hild r e s traint s
Table SUMMARISING THE installation OF ISOFIX CHILD SEATS
III
In conformance with European law (ECE 14-06), this table shows you the possibilities for the installation of ISOFIX
child seats in seats fitted with ISOFIX anchoring points.
For ISOFIX universal and semi-universal child seats, the ISOFIX size class, defined by a letter from A to G, is shown
on the child seat to the right of the ISOFIX logo.
Weight of child/Age given as a guide
Up to 10 kg
(group 0)
Up to around 6
months
Up to 10 kg and up to
13 kg (groups 0 and
0+)
Up to around
1 year old
Shell(*)
“Rear-facing”
Type of ISOFIX child seat
ISOFIX size class
F
G
C
D
9 - 18 kg (group 1)
From approx. 1 to 3 years
“Rear-facing”
E
C
D
“Forward-facing”
A
B
Front passenger seat
X
IL-SU
IL-SU
IUF
IL-SU
Lateral rear seats
IL-SU
IL-SU
IL-SU
IUF
IL-SU
Central rear seat
B1
Non ISOFIX seat
IUF: Seat position suitable for installation of an ISOFIX universal child seat. ISOFIX “forward-facing” child seats
equipped with a top belt for attaching on the top ring in the vehicle's ISOFIX seat positions.
IL-SU: Seat position suitable for installation of an ISOFIX semi-universal child seat. ISOFIX “forward-facing” child
seats equipped with a bar, ISOFIX “rear-facing” child seats, or ISOFIX shell seats equipped with either a top belt or
a bar.
X: Seat not suitable for installation of an ISOFIX seat of the size class indicated
(*): The ISOFIX shell, fixed to the lower rings of an ISOFIX seat, takes up 2 rear seats
112
C hild r e s traint s
RECOMMENDED ISOFIX CHILD SEAT
III
ISOFIX child seat
recommended
The ISOFIX child seat recommended for your vehicle is the
RÖMER Duo Plus ISOFIX. It is
sold by the CITROËN network.
It is equipped with a top belt and so
is approved as an “ISOFIX universal” child seat, size class B1. It is
essential to use the top belt.
This ISOFIX child seat can also
be installed in seats not fitted
with ISOFIX anchoring points. In
this case, the child seat must be
secured by means of the vehicle
seat belt.
In the front passenger's
seat position, it is
imperative to deactivate
the front passenger's
airbag if you are
installing a “rear-facing” child
seat there. Otherwise the child
risks being killed or seriously
injured should the airbag
deploy.
Take care to comply with the
fitting instructions given in
the child seat manufacturer’s
installation guide.
113
I nt e rior lighting
III
1
2
2
2
1
1
2
Front
1.Interior lamps
Move control 1 to one of the 3 following positions:
The interior lamp comes
on when you open a door
or the boot.
The interior lamp is deactivated and remains permanently off.
Lighting is permanent.
Automatic lighting of the
interior lamps
114
• On entering the vehicle:
They come on as soon as the
vehicle is unlocked or a door is
opened.
They go out 30 seconds after
the doors are closed or when
ignition is switched on.
Rear
• On vacating the vehicle:
They come on as soon as the
ignition key is removed (timed
for 30 seconds), or when a
door is opened.
They go out 30 seconds after
all the doors have been closed
or immediately after the vehicle
has been locked.
2.Spotlamps
The spotlamps only function when
the ignition is switched on, but not
in economy mode.
Move one of the controls 2 to the
following position:
The spotlamp is on.
Rear reading lamps
(Tourer with panoramic roof)
With the key in the DRIVE or
STARTING position, press the
corresponding switch.
The rear reading lamps come on
when the key is removed from the
ignition and when the vehicle is
unlocked.
They go out gradually once the
ignition is switched on or the
vehicle is locked.
F Pressing switch 1 switches on
the corresponding rear reading
lamp for a duration of 10
minutes.
I nt e rior lighting
III
Door opening controls
lighting
A
B
Ambient dashboard lighting
Your vehicle is equipped with warm
and welcoming ambient lighting.
A soft orange light is emitted.
Operation
When starting the engine, lights
located along the dashboard are
activated.
With the ignition on and the headlamps on, button A allows you to
activate or deactivate the ambient
dashboard lighting.
They are located on the front and
rear interior door opening controls.
The rear door opening controls
lighting is deactivated if child safety
is activated.
Ambient central console
lighting
These lights are located on the
roof console, near the front interior
lamp. They light up the central console.
Operation
These lights are activated when
the instrument panel comes on.
They are deactivated when the
instrument panel goes out.
The intensity of the lighting varies
along with that of the instrument
panel. Press buttons B to increase
or reduce the intensity of the lighting.
115
I nt e rior lighting
Welcome lighting
The welcome lighting is made up of:
• The interior (roof) lamps.
• The floor lighting.
• The pavement lighting when a
door is open.
III
Front door storage pockets
automatic lighting
A white light is emitted to light up
the door storage pockets.
Operation
The lighting come on automatically
when you place your hand inside
the storage pocket. It goes out a
few seconds after you remove your
hand.
Pavement lighting
With the door open, this lights up
the ground next to the vehicle.
Floor lighting
In the front and the rear of the vehicle, when a door is opened, this
lights up the interior of the vehicle.
116
I nt e rior comfort
III
B
C
A
Front armrest
The armrest gives you extra comfort in your driving position.
To optimise your driving position,
lift the control A and push the armrest forwards.
The armrest returns to its initial
position when you push it rearwards.
Cup-holder in front armrest
Lift up the armrest to access the
cup-holder.
Air conditioned glovebox
To open the glovebox, pull on the
handle and lower the lid.
The glovebox has a manually closable air conditioning vent B.
It has 2 or 3 sockets C to connect
audio/video equipment.
It has automatic lighting.
It gives you access to the fusebox
underneath the dashboard.
Driver's oddments tray
To open the driver's oddments tray,
pull the handle towards you.
Whils t dr iv ing, the
glovebox should be
kept closed.
117
I nt e rior comfort
III
A
B
Rear cup-holder
The rear cup-holder A is located in
the rear central armrest.
Rear armrest storage
Lift up the upper part of the rear
central armrest to access storage
space B.
12 volts accessory socket
118
This is located in the rear ashtray.
Mat
When removing the driver's side
mat:
• Slide the seat back as far as
possible.
• Unclip the fixings.
• Remove the fixings, then the
mat.
When replacing, correctly position
the mat and clip the fixings in.
Check that the mat is correctly held
in place.
To avoid your feet becoming jammed under the pedals:
• Only use mats which are suitable for the fixings already present
in the vehicle. The use of these fixings is essential.
• Never stack up more than 1 mat.
The use of a mat not approved by CITROËN may obstruct access to
the pedals and hinder the cruise control / speed limiter function.
Floor mats approved by CITROËN are fitted with a 3rd fixing located
in the pedal area to avoid any risk of interference with the pedals.
I nt e rior comfort
B
D
C
D
A
Sun visor
To prevent dazzle from ahead, fold
the visor downwards.
They can be disengaged from their
central fixing and pivoted over to
the side windows if required.
Rear door blinds
Pull on tongue A and position the
blind on hook B.
III
Rear blind (saloon)
Pull the grip C to unroll the blind.
Fasten the blind to fixings D.
Sun visor with illuminated
mirror
Illuminates automatically on opening
the mirror cover flap (ignition on).
119
B O O T ( s aloon )
Luggage securing rings
III
1
3
2
1 Battery for vehicles with V6 HDi engine.
2 Pull strap (spare wheel storage).
3 Boot lamp.
4 6 CD changer.
120
4
Use the 4 securing rings on the
boot floor to secure your luggage.
For safety reasons, in case of the
need for sharp braking, you are
advised to place heavy objects as
far forward in the boot as possible.
B O O T ( T our e r )
III
3
1
2
1
1
2
5
1Luggage-cover blind
(see details on following page)
1 Boot lamp
2
3
4
3
1Hook
Allows you to hook shopping
bags.
2 Torch
To recharge, return it to its
storage position.
3Storage net
or
Battery compartment (for
vehicles with V6 2.7 HDi
engine).
2Luggage securing rings
Use the 4 stowing rings provided on the boot floor to secure
your loads.
Note : For safety reasons in the
event of sharp braking, you are
advised to place heavy objects
as far forwards as possible.
3Hooks
These allow a cargo net to be
fitted (see details on following
page).
2 12 V accessories socket
(100 W maximum)
Cigar-lighter type 12 volts
socket. It is located on the rear
right-hand trim, and is supplied
from the ignition position.
3Loading assistance
You can change the height of
the vehicle in order to make
loading or unloading easier.
4Hook
Allows you to hook shopping
bags.
5Storage net
or
6 CD changer
121
L U G G A G E - C O V E R B L I N D ( T our e r )
III
A
1
B
C
To install :
To fold up :
To remove :
• Position the left-hand end of the
luggage-cover blind in its housing
A behind the rear benchseat.
• Press gently on the handle
(PRESS).
The
luggage-cover
blind rolls up automatically.
The moveable section C can be
folded up along the backrest of the
rear benchseat.
• Press gently on the handle
(PRESS). The luggage-cover blind
rolls up automatically.
• Squeeze the blind’s control 1 and
position it in place in its housing B
to the right-hand side.
• Release the control to secure the
luggage-cover blind.
• Unroll it until it locks into place on
the boot pillar.
122
• Squeeze control 1 and lift up the
luggage-cover blind to the right
then to the left to remove it.
CARGO NET (Tourer)
2
2
1
4
4
3
3
1
• Unroll the cargo net and position one of the ends of the net’s
metal bars in the corresponding
fixing location. Ensure that the
notch is correctly lodged in the
rail located inside the location 3.
• Pull on the cargo’s net’s metal
bar to position the other notch in
the 2nd fixing location.
III
To use in row 2 :
The cargo net can be used behind
the rear seats (row 2) when the
luggage-cover blind is not fitted, or
behind the front seats (row 1).
Note : when using behind the front
seats, the backrests and the seat
cushions must be folded down
(see section on rear seats).
To install :
• Fold down the backrests of the
rear seats.
• Position the cargo net roller over
the two rails 1 located behind
the rear seats (2/3 benchseat).
The two notches 2 must be positioned over the two rails.
• Slide the 2 rails 1 into the notches
2 and push the roller (lengthwise)
from right to left to lock it in.
• Put the backrests of the rear
seats back into place.
To use in row 1 :
• Fold down the
backrests of
the rear seats.
• Open the covers 3 of the
corresponding
high fixing locations.
• Open the covers 4 of the
corresponding high fixing
locations.
• From the rear
benchseat, unroll the cargo net
by pushing it to disengage the
retaining notches.
• Position one of the ends of the
cargo net’s metal bar in the corresponding fixing location. Ensure
that the notch is correctly lodged
in the rail located inside the location 4.
• Position the other notch in the
2nd fixing location and pull the
metal bar towards you.
123
SUNROOF (SALOON)
Anti-pinch
A
III
B
Glass sun roof
Sun roof closed
• Press A to first notch: tilting.
• Press A to second notch: automatic complete tilting.
• Press B to first notch: sliding
towards rear.
• Press A to second notch: automatic total sliding towards rear.
Sun roof open
• Press A to first notch: closure.
• Press A to second notch: automatic total closure.
Tilted sun roof
• Press B to first notch: closure.
• Press A to second notch: automatic total closure.
124
An anti-pinch device stops the sun
roof from closing, whether sliding
or tilting. If it meets an obstacle, it
re-opens.
After a battery disconnection or
if there has been a malfunction,
you have to re-initialise the antipinch function.
To do so, move control A to completely open the sun roof, then
keep control A pressed down for a
minimum of 1 seconds.
Warning: During this manœuvre,
the anti-pinch does not operate.
Your sun roof is fitted with a manually-operated blind.
Always remove the ignition key when leaving the vehicle, even
if for a short time.
In the event of anything being caught by the sun roof closing,
you must reverse the roof movement.
To do that, reverse the position of the control concerned.
When the driver is operating the sun roof, he or she must always
make sure that the passengers are not preventing it from closing
properly.
The driver must ensure that passengers use the sun roof control
correctly.
Pay special attention to where children are when
operating the sun roof.
The fitting of a sun roof as an accessory is prohibited.
PA N O R A M I C S U N R O O F ( T our e r )
Notes :
A
B
1
After a battery disconnection, or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function :
III
- press control A to the 2nd notch
(fully open),
2
- wait until the panoramic sunroof
is fully open,
- press control A for at least 3
seconds.
This device comprises a tinted glass
panoramic surface 1 to improve
brightness and vision in the passenger compartment.
It is fitted with an electrical blind 2
to help maintain a comfortable temperature.
Sequential opening
Press control A.
Pressing to the 1st notch allows you
to open the panoramic sunroof step by
step.
Pressing to the 2nd notch allows you to
fully open the panoramic sunroof.
The panoramic sunroof stops in the closest pre-defined position (11 positions)
as soon as you release the control.
Sequential closing
Press control B.
The panoramic sunroof stops as
soon as you release the control.
Anti-pinch
If the panoramic sunroof meets an
obstacle whilst closing, it stops and
opens partially again.
You must re-initialise the anti-pinch
function within 5 seconds of the
panoramic sunroof stopping :
- Press control B until the panoramic
sunroof is fully closed (closing in
steps of a few centimetres).
If the panoramic sunroof opens
randomly
during
a
closing
operation, and straight after the
panoramic sunroof stops :
- Press control B until it closes
fully.
During these operations,
anti-pinch function does
operate.
the
not
In the event of anything being caught when the panoramic sunroof is moving, you must reverse the
movement of the panoramic sunroof. To do so, reverse the position of the control.
When the driver is operating the panoramic sunroof, he or she must always make sure that the
passengers are not preventing it from closing properly.
The driver must ensure that his passengers are using the panoramic sunroof correctly.
Pay special attention to children when operating the panoramic sunroof.
125
A udio s y s t e m
T e l e matic s
IV
Control panel
CD changer
126
See NaviDrive instructions
R D S audio compact di s c s y s t e m
A
B
C
D
E
F
G
H
I
J
K
IV
S
R
Q
O N M
L
Multifunction display
1
2
P
10
3
4
Technical specifications
5
6
7
8
9
11
Your Bluetooth® compatible radio possesses:
• 3 wavebands (MW/LW/FM).
• Dual tuner with RDS EON PTY, display of the PS
name, RDS programme search, TA traffic information, 24 pre-selections (18 FM - 6 MW/LW), automatic memorisation of the AST strongest stations.
• An MP3- compatible CD player.
• Audio power of 4x35 W.
127
B utton control s
IV
A
On / Off.
Volume adjustment.
B
CD eject.
C
CD aperture.
D
E
BAND/
AST
Short press: Selection of frequency bands and memory
banks.
Long press: Automatic pre-set function (Autostore).
Call-up of audio adjustments:
Sound ambiences, bass, treble, loudness, fade, balance,
speed-sensitive volume.
G
LIST
Radio source:
Short press: Display of the list of radio stations available
(30 maximum).
Long press: Update of list of stations.
CD source: Display of list of tracks of the CD.
H
ESC
Short press: Cancel the current operation or delete a superimposed display.
Long press: Return to the permanent display.
I
TA/PTY
K
OK
Selection of source (CD/MP3 CD and CD changer source).
F
J
128
SOURCE
L
Short press: TA function (road information).
Long press: PTY function (selection of programme type).
M
Radio source: Manual search of lower frequencies.
CD/MP3 changer source: Selection of the next CD / next
CD-cover.
Other sources: Scrolling in the Main Menu.
N
Radio source: Automatic search of lower frequencies.
CD source, CD changer source and MP3 source:
Short press: Reverse search for tracks.
Long press: Rapid reverse with accelerated sound.
Other sources: In the menus, choice of your adjustments.
If your vehicle has the Bluetooth® system: Selection of
characters.
Display of the Main Menu.
In certain countries, this control is deactivated while the vehicle is moving.
O
MENU
P
1-6
Q
DARK
Short successive presses:
One press: Display of radio, time and temperature only.
Two presses: Display off (blank display).
Three presses: Return to the standard display.
R
MODE
Selection of the type of information shown on multifunction
display.
Radio source: Manual search of higher frequencies.
CD/MP3 changer source: Selection of previous CD / previous CD-cover.
Other sources: Scrolling in the Main Menu.
Radio source: Automatic search of higher frequencies.
CD source, CD changer source and MP3 source:
Short press: Forward search for tracks.
Long press: Fast forward with accelerated sound.
Other sources: In the menus, choice of your adjustments.
If your vehicle has the Bluetooth® system: Selection of
characters.
Button for validation and activation/deactivation of certain
functions.
If your vehicle has the Bluetooth® system: Answer call, end
call.
S
Radio source:
Short press: Recall of pre-set stations.
Long press: Memorisation.
CD changer source: Selecting a CD.
CD changer.
B utton control s
The controls at the steering wheel give you access to certain functions, without you needing to use the radio-CD control panel.
Short press
1
2
- Cancel the current operation and return
to the previous multifunction display
screen.
- For an incoming call: Refuse the call.
Long press
Return to the original multifunction display.
Rotate
- Radio mode: Scroll through pre-set stations.
- CD/MP3 CD and CD changer source: Scroll
through CDs or chapters.
- In the multifunction display menus: Move
around and increase/decrease.
RIGHT
CONTROL
Short press
- In the multifunction display menus: Validation.
- Open shortcut menus.
- For an incoming call: Answer call.
Long press
Open the multifunction display main menu.
MENU
Short press
Access the multifunction display main
menu.
VOL +
Short press /
Press and hold
5
VOL -
Short press /
Press and hold
6
MUTE
Short press
3
4
IV
- First press: mute.
- Second press: cancel mute.
Long press
-C
D/MP3 CD and CD changer source:
Fast forward with accelerated sound.
Short press
- Radio source: Automatic search of lower frequencies.
-C
D/MP3 CD and CD changer source:
Search of previous track.
Long press
-C
D/MP3 CD and CD changer source:
Rapid reverse with accelerated sound.
Short press
-R
adio source: Display of the list of radio
stations available.
-C
D/MP3 CD and CD changer source:
Display of list of tracks of the CD.
Long press
Update of list of stations.
Short press
Activation of voice recognition.
Long press
Navigation instructions.
7
8
9
LIST
Increase volume.
Decrease volume.
Short press
- Radio source: Automatic search of
higher frequencies.
-C
D/MP3 CD and CD changer source:
Search of the next track.
10
11
LH
BUTTON
RH
BUTTON
Press
Scroll through the multifunction display
screen.
129
G e n e ral function s A udio adju s tm e nt s
On / Off
IV
With the key in Drive position M,
press on control A to switch the
radio on or off.
Note:
• If the radio was on the last time
you switched off the ignition, it
will resume automatically when
you switch on the ignition again.
You will not have to press on
control A.
• After switching off the ignition,
you can still operate the audio
system even without the ignition key being present. Simply
press on button A. The system
will turn itself off after approx.
30 minutes.
Anti-theft system
This radio is coded in such a way
as to function only on your particular vehicle. It would be unusable if
installed on any other vehicle.
Note: The anti-theft system is
automatic and requires no action
on your part.
Selection of source
To select either Radio, CD (CD
already inserted and Radio source
activated), or CD changer source,
press on control D.
When you insert a CD it automatically starts being read.
Note: When the radio is switched
off, the source selected is memorised.
Volume adjustment
Rotate control A to increase or
decrease the sound volume.
You can also increase or decrease
the volume using controls 4 and 5
at the steering wheel.
Note:
• The sound volume when you
switch off the radio will be the
same when you switch it on
again.
• The radio sound volume automatically adjusts to the vehicle
speed, provided the “volume
adjustment” function is activated.
Temporary sound pause
130
Press on control 6 at the steering
wheel to activate this function.
The sound will be paused, regardless of the source selected.
To restore sound, press on control 6 at the steering wheel or on
one of the controls 4 or 5 at the
steering wheel.
Sound adjustments
Each press on button F brings up the
parameter to be adjusted: choice of
predefined sound ambiances, bass,
treble, loudness, fade (front/rear
sound distribution), balance (left/
right sound distribution) and volume
adjusted to vehicle speed.
Press buttons K or N to modify the
values for the function displayed.
Note:
• The selection of a sound ambiance automatically adjusts bass
and treble. These can be modified.
To restore the original adjustments for the musical ambiances,
reset bass and treble to zero.
• Adjustment of loudness, as well
as bass and treble when they
are available, are specific to each
sound source and to each musical ambiance.
• If you leave the audio system unactioned for a few seconds, it will
revert to the normal display.
Remark: A superimposition of ambiances, loudness and bass adjustment
may cause vibrations/interference
and result in poor sound quality.
R adio s ourc e
Notes on radio reception
Your radio will be subject to certain
phenomena that are not encountered by domestic systems.
The reception of AM and FM signals may suffer from interference,
which is caused by the nature and
propagation of the signals and
does not reflect on the quality of
your radio installation.
In AM mode, the reception may
be affected when passing under
power lines or bridges, or when
travelling through tunnels.
In FM mode, the reception may
be affected by the distance from
the station transmitter, the reflecting of signals off obstacles (mountains, hills, tower blocks) and radio
blackspots (no coverage from the
station transmitter).
Selection of radio source
Press button
source.
D
to
select
the
Selection of frequencies and
memory banks
Press
button E
successively
to
go
through
the
memory
banks FM1, FM2 and FM3, for
the FM waveband, and the memory banks MW/LW, for the AM
waveband.
Manual search
Manual search is via buttons J
or M.
By keeping button J or M pressed,
you will be able to scroll through
the waveband. Scrolling will stop
as soon as you release the button.
The radio will remain tuned to the
frequency that is displayed.
Tuning sensitivity
Automatic searches can be carried
out according to two levels of sensitivity:
• To capture the most powerful
transmitters, choose the local
search mode “LO” (default
option).
• To capture the weakest or most
distant transmitters, choose the
sensitive search mode “DX”.
Searching for a station is done first
in “LO” (local) sensitivity, then in
“DX” (distant) sensitivity.
To commence a search in sensitivity mode “DX” (distant) immediately, press twice in succession on
one of the buttons K or N.
IV
Automatic search
A short press on one of the buttons
K or N will tune into higher or lower
radio stations respectively, within
the chosen waveband.
By keeping button K or N pressed,
you will be able to scroll through
the waveband. The scrolling will
stop at the first station it finds once
the button is released.
You can also do this by means of
the controls 7 and 8 at the steering
wheel.
If the automatic search is unable to
tune into a known frequency (perhaps owing to very weak reception), it is possible to search manually to find this station.
131
R adio s ourc e
IV
Display and selection of a
station available in the area
in which you are travelling
Briefly press on button G or button 9 at the steering wheel to display the list of stations. This list is
updated every 10 minutes.
You can also update this list at any
time by making a long press on
button G or button 9 at the steering wheel.
To listen to one of these stations,
select by pressing buttons J or M
and validate using button L.
Manual pre-setting
Select the waveband and memory
bank required using button E.
Select a station using either automatic or manual search.
Keep pressing for more than two
seconds on one of the pre-selection
buttons 1 to 6 on the keypad P.
The sound momentarily cuts off,
then returns to its previous level to
confirm that it has memorised the
station.
132
Automatic memorisation
of transmitters (Autostore
function)
In FM, if you hold down button E
for more than two seconds, your
radio will automatically memorise
the 6 strongest stations on the FM3
memory bank.
The display shows “FM AST”.
The radio memorises the 6 strongest transmitters, deleting the 6 previously memorised.
After the memorisation, the radio
goes directly to memory 1 of memory bank FM3.
Note:
• If the traffic information function has been activated (see
RDS SYSTEM), the stations
offering this facility will be memorised as priority.
• If it is unable to memorise any
new stations, the system will
retain the previously memorised stations.
• If the system is unable to find
6 stations, the unfilled memory
slots will remain free.
Recall of pre-set stations
Press button E briefly to select the
required waveband and memory
bank.
A short press on one the pre-selection buttons 1 to 6 on the keypad P
recalls the corresponding memorised station. You can also do this
using the control 2 at the steering
wheel.
If it is a RDS station, the frequency
appears some seconds before the
name appears.
For RDS stations, recall of a station may prompt a search for a frequency corresponding to the region
where you happen to be (see RDS
system).
RDS system
Using the RDS (radio data
system) function on FM
The majority of FM radio stations
use the RDS system. The radio in
your vehicle has this system.
The RDS system enables these
stations to transmit non-audible
data in addition to the broadcasting
of their programmes. The data provides access to various functions
described in this chapter, such as:
display of the station name, intermittent traffic information flashes
or automatic scanning of stations.
This enables you to continue listening to your chosen radio station,
regardless of the different frequencies it uses in the regions through
which you are travelling.
Scanning of RDS stations
Your radio keeps the best possible
reception by continuously looking
for any other frequencies on which
the selected radio station is broadcast, automatically choosing the
frequency offering the best reception (if the station broadcasts on
more than one transmitter or frequency).
Activation/deactivation of
the RDS functions
The RDS
functions
can
be
accessed via the following two
menus:
• Main menu (press button O).
• AUDIO menu (press button L).
To activate/deactivate the
RDS functions
1.Press on button O.
2.Select the AUDIO icon using
buttons J or M.
3.Confirm your choice with a
press on button L.
4.Select the sub-menu for the FM
waveband, via buttons J or M.
Confirm your choice with a
press on button L.
5.Select scanning for RDS stations, via buttons J or M.
6.Validate your choice with a
press on button L.
7.Using control L, select/deselect
to activate/deactivate the function.
8.Validate your choice by selecting “OK” on the display.
Note:
If the RDS function is active.
• The “RDS” on the display will
light up provided the station
being received uses the RDS
system with frequency search.
• The “RDS” on the display is
barred if the station received
uses the RDS system without
frequency search.
If your RDS function is deactivated,
the “RDS” on the display will be
absent in all cases.
The display will indicate the
“NAME” for the stations that use
the RDS system and the frequency
for stations that do not use it.
IV
133
RDS system
Regional search mode
IV
Some stations, when they are
organised in networks, broadcast
regional programmes at certain
times of day, and national programmes at other times.
It is possible to search.
• Either for a regional station only.
• Or across the whole network
in order to find a different programme.
To activate/deactivate this function,
proceed as for Scanning of RDS
stations.
Note: When this mode is activated,
the system will remain tuned to one
specific regional station.
TA traffic information (traffic
announcements)
Some stations allow broadcasting, only in FM, of these messages
thanks to the “TA” function.
You can activate the “TA” function by pressing on button I. This
allows you, even though you are
listening to another audio source
or to a radio programme not itself
providing traffic messages, to
receive traffic information flashes
from an FM station which broadcasts them.
134
While the messages are being broadcast the original source is paused and
when the messages have ended your
radio will automatically revert to the
music programme you were listening
to.
Note:
• You have to be in FM wave band.
• The station being listened to
should indicate via the RDS system that it broadcasts traffic information.
• Stations organised in a network
(EON) have regional transmitters
that send their own programmes:
while you are listening to one of
these stations the system will
switch automatically to a station
on the network that is broadcasting traffic information.
• You can stop listening to a message by pressing button I.
Sound volume adjustment
for traffic information
The sound volume for traffic information operates separately from
that for the rest of the system, and
can be adjusted independently.
Rotate button A while a traffic information message is being broadcast.
This volume adjustment is memorised.
Selecting a programme type
Certain stations offer the possibility of listening to a particular programme type, selected from a list
(PTY).
Press for more than two seconds
on button I.
Press on buttons J or M to scroll
through and select the programme
type you prefer, then press on button L to validate your choice.
Searching for a station
broadcasting this
programme type
When you have chosen a programme type, the list of corresponding stations appears on the
display, press on buttons J or M to
scroll down and select the station
you want, then press on button L
to validate your choice.
Quitting pty mode
To quit “PTY” mode, select the
function to deactivate “PTY” in
the list of the different programme
types.
Radio text via contextual
menu
This function allows to view the
information broadcast by the station, concerning the programme
you are currently listening to.
To activate/deactivate this function,
proceed as for Scanning of RDS
stations.
C D s ourc e
Selecting CD source
After inserting a CD, with the printed
side facing upwards, the player will
start playing the CD automatically.
To change manually to CD source
(CD already inserted), press button D until you obtain the source
you require.
Ejecting a CD
Press button B to eject the CD,
the audio system will automatically
switch to radio source.
If the CD is not removed within 10
to 15 seconds of being ejected, it
will automatically be taken back
into the CD player, although it will
not be played.
Selecting a track
Press button K once to play the
next track.
Press button N once to return to
the beginning of the track currently
being played, press a second time
to go back to the start of the previous track.
Press the buttons successively to
skip several tracks at a time.
You can also perform this operation using button G or button 9 at
the steering wheel.
When the track listing is displayed,
select the desired track using buttons J or M then validate with button L.
You can also do this via the controls 7 and 8 at the steering wheel.
Fast forward and rapid
reverse with accelerated
sound
To move swiftly through the CD,
press and keep pressed button K
or N, respectively for fast forward
or rapid reverse with accelerated
sound.
You can also do this via the controls 7 and 8 at the steering wheel.
Play resumes as normal when the
button is released.
Menu
This menu allows activation/deactivation of two options:
• Playback of the first 7 seconds
(approx.) of each track of the
CD.
• Random playback of the CD
tracks.
This can be accessed in two ways:
• Either by pressing button O
and proceeding as for Scanning of RDS stations – the submenu for Audio Preferences.
• Or, provided you are in CD
source, by pressing on button L. You can then access the
Audio menu.
Note: If one of these options is
active, it remains active for CD
changer source.
Safety precautions
For safety, do not use a CD player
if the cabin temperature is higher
than +60 °C or lower than -10° C.
If the temperature becomes too
high, an automatic safety device
will prevent the CD player from
working until an acceptable temperature is restored.
IV
Handling of CDs
• Do not drop them.
• Store the CDs so that they are
kept free of dust. Avoid touching the disc surface as any
scratches may adversely affect
the sound quality.
• Do not attach any stickers to
the discs.
• Do not write on them.
• Do not use damaged or
deformed discs.
• Do not expose them to heat or
direct sunlight.
If the surface of the compact disc is
dirty, it can be wiped with a soft, clean
cloth. Always wipe from the centre of
the disc outwards.
135
M P 3 C D s ourc e
MP3 CDs
IV
The MP3 format (MPEG 1,2 & 2,5
Audio Layer 3) is an audio compression standard that permits
recording of 10 times as many
musical files on one CD.
Your radio only plays back files
which have the extension “.mp3”.
Other types of files (.wav, .mpg4,
.ogg, midi...) cannot be played
back.
When you insert an MP3 CD, the
radio searches all the musical
tracks. Playback may require some
tens of seconds before starting.
Playback of the MP3 CD is optimised if the level of the cover is
limited to 2.
Burning format
136
Some burnt CDs cannot be read
by your equipment (quality, speed
of recording, etc.).
When you burn a CD-R or CD-RW,
select the burning standard ISO
9660 level 1.2 or Joliet. Playback
of other formats may not occur correctly.
Use the Joliet standard to burn
multi-session CDs.
On a given CD, always use the
same burning standard.
To obtain the best possible acoustic quality, select the lowest burning speed.
It can handle transmission speeds
of 8 to 320 kbits/s and playback
of 22.05 to 44.1 kHz.
MP3 CD player
Your Audio CD system may be
MP3 compatible.
As you insert a CD recorded in
MP3 format, playback starts of the
first song of the first CD-cover.
You can select a particular track by
using buttons N or K and CD-covers using buttons J or M.
To select a track
To display the list of CD-covers,
press on button G.
Use buttons J or M to select the
CD-cover you wish to listen to.
To open a CD-cover, press L.
Use buttons N or K to select the
track you wish to listen to.
Validate with a press on L.
Menu
This menu is for activation/deactivation of three options:
• Playback of the first 7 seconds
(approx.) of each track of the
CD.
• Repetition of the current CDcover.
• Random playback of CD-cover
tracks by CD-cover.
This can be accessed in two
ways:
• Either by pressing button O
and proceeding as for Scanning of RDS stations – the submenu for Audio Preferences.
• Or, provided you are in CD
source, by pressing on button L. You can then access the
Audio menu.
Your Audio equipment may enable you
to listen to musical works. Musical
work is protected by law. Non-respect
of the law can lead to prosecutions.
C D chang e r s ourc e
CD Changer
This equipment S (if present) is located
in the vehicle boot and comprises a
magazine that holds up to 6 CDs.
To insert/remove a CD
1.Remove the magazine from the
CD changer
• Open the flap located on the righthand side of the boot to access
the CD changer.
• Press on the “EJECT” button to
eject the magazine partially.
• Remove the magazine carefully.
• Close the sliding door.
2.Removing a compartment
Take out just one drawer at a time.
3.Inserting/removing a CD
• Insert a single CD, printed side
upwards. Otherwise the CD
changer will not operate.
• Pull out the CD by pulling on the
part that is showing.
4.Repositioning the compartment
Refit the drawer by pushing it into
the magazine. Do not push directly
on the CD.
5.Repositioning the magazine
• Open the sliding door.
• Hold the magazine, narrow side
towards the opening of the CD
changer.
• Push the magazine gently into the
aperture of the changer until there
is a click.
• Reclose the sliding door to prevent
entry of dust or of foreign bodies.
• Close the flap.
Selecting CD changer source
Press on button D until you reach
CD changer.
After the magazine engages, playback of the first track of the first CD
will begin.
Selecting a CD
To select a CD, either press one of
the pre-selection buttons 1 to 6 on
the keypad P, or scroll using buttons J or M.
The CD will start to play automatically.
You can also do this by means of
control 2 at the steering wheel.
After each change of source, on
return to CD changer source, playback will resume at the same point
where it had been interrupted.
Selecting a track
Press button K once to play the
next track.
Press button N once to return to
the beginning of the track currently
being played, press a second time
to go back to the start of the previous track.
Press the buttons successively to
skip several tracks at a time.
You can also do this by means of
the controls 7 and 8 at the steering
wheel.
Fast forward and rapid reverse
with accelerated sound
Press and keep pressed one of
the buttons K or N respectively for
fast forward or rapid reverse with
accelerated sound. Play resumes
as normal when the button is
released.
You can also do this by means of
controls 7 and 8 at the steering
wheel.
IV
Menu
This menu is for activation/deactivation of three options:
• Playback of the first 7 seconds
(approx.) of each track of the
CD.
• Repetition of the current CD.
• Random playback of tracks, CD
by CD.
This can be accessed in two ways:
• Either by pressing button O
and proceeding as for Scanning of RDS stations – the submenu for Audio Preferences.
• Or if you are in CD changer
source by pressing button L.
You then have access to the
AUDIO menu.
Note: If one of these options is
active, it remains active for CD
source.
137
B lu e tooth ®
IV
Your audio system may be
Bluetooth® compatible. It allows
you to connect a mobile telephone for use “hands free” and
even to use its directory.
It permits you to twin up to four telephones, to be able then to connect whichever one you choose.
The Bluetooth® functions available
and the content of the display are
dependent on the type of mobile
telephone, its settings and the type
of contract you have. For this reason it is advisable to make enquiries with your telephone provider.
Prior to any operation:
• Your display should be lit up
(key in position M).
• Your telephone's Bluetooth®
system must be activated.
Twinning a telephone
Twinning a telephone consists
of having it recognised by the
Bluetooth® system on your vehicle.
This then permits an instantaneous
connection.
Twinning can only be performed
with ignition switched on, display
illuminated, engine stopped. No
other telephone should be connected.
• The twinning must be performed
with the telephone and its
Bluetooth® system activated.
Note: Refer to the user instructions to familiarise yourself with the
features of twinning.
• The telephone detects the
Bluetooth® system on your
vehicle. “CITROËN” displays
on your telephone.
You should then select “CITROËN”
on your telephone controls. Next
you have to accept or decline this
twinning.
Note: If the 4 twinning memories
are already being used, you must
select a memory that is already
attributed although the telephone
twinned to this location will no
longer be.
• Next the telephone asks you
to enter an identification code:
1234.
• Validate.
Note: This entry may be demanded
earlier in the twinning sequence.
The telephone is now twinned to
your Bluetooth® system. For immediate access to the Bluetooth®
functions, it may be necessary to
make a connection (see following
page Configuration : Connecting
a twinned mobile telephone).
Once the twinning is finished, you
will be able to connect your telephone via the “Main menu”.
Connecting a twinned
telephone
Each time you enter the vehicle,
after switching on the audio system,
your telephone is detected automatically. If more than one telephone is
present, the last telephone to have
been connected is the first to be recognised.
Note: Disconnections may occur.
You may have to make a new connection (see following page, Configuration : Connecting a twinned
mobile telephone).
Remarks:
• In the event of a problem, it is
recommended to switch your telephone off and then on again.
• If you switch off your telephone
within the field of reception of the
Bluetooth® system on your vehicle, the next connection will not
be automatic. To restore automatic connection, you will have
to connect your telephone manually (see following page, Configuration : Connecting a twinned
mobile telephone).
• If you are already in telephone
communication when the audio
system is turned on, the latter
detects the telephone.
• To avoid interference, you are
advised not to place your mobile
telephone close to your radio.
To accept an incoming call
138
Using button L or control 2 at the
steering wheel.
B lu e tooth ®
Main Menu
Press on the Menu button O to
access to Main menu, then select
the “Telephone” icon using buttons J or M), then validate the
selection via button L.
You have access:
• To the Directory.
• To Configuration.
• To Communication Management.
You access your choices via (J
or M), then you validate them with
a press on L.
This main menu can also be
accessed by pressing button E
then button L.
Folder
This menu lets you open:
• The telephone Directory of the
telephone that is connected.
• The Calls List.
Telephone directory
A telephone call can be made
independently of the telephone or
of the audio system, thanks to the
directory.
The directory is displayed. Select
the number via J or M, then validate with a press on L.
Remarks:
• The directory displayed updates
itself automatically.
• If the person to be called does
not figure in the directory, the
call can only be made using the
telephone.
• If you have information recorded
in the Vcard format, you must
select the person you wish to
call, then validate. A list of 4
numbers maximum can be displayed with the following labels :
“Home”, “Office”, “Mobile” and
“Car”.
Calls list
After selecting this component and
then validating, the calls list is displayed with a maximum of: 10 calls
made (arrow pointing upward), 10
calls received (arrow pointing
downward) and 10 calls not connected.
It is possible to make a call starting from this list: Select the number
via J or M, then validate with a
press on L.
Configuration
This menu allows you to:
• Deleting a twinning. Using J
or M, select this choice, then
validate on L. Select in the list
the telephone that you no longer
wish to have twinned. Validate.
• Consulting the list of twinnings. The list of telephones
twinned is displayed.
• Connecting a mobile telephone that is twinned. Select
the telephone that you wish to
connect. This access allows
you to make a connection manually.
IV
Call management
This menu is accessible during
your calls, permitting you to:
• Swap a call if there is another
call incoming.
• End a call.
• Be in Secret mode.
Remark:
If you are in telephone conversation, you have access to this menu
“Configuration” by pressing L.
139
B lu e tooth ®
Swapping a call
IV
During a telephone conversation,
the system is able to tell you of a
second call incoming. To accept it,
validate. To change from one call
to the other, select this choice.
End a call
This choice enables you to end a
telephone conversation, for example if there is another call incoming.
Secret mode
Select this choice. This allows
you not to be heard by the other
person. To restore sound to the
other person, select deactivation
of Secret mode in the menu “Call
Management”.
Note: If you wish to transfer a call
from the audio system to the mobile
telephone (for example when leaving your vehicle), refer to the user
instructions for the latter.
140
Voice recognition
Pressing on the end of the lighting
control stalk 10 starts telephone
voice recognition.
Voice recognition allows you to
make a call to a number for which
you have recorded a label on the
mobile telephone that is twinned
and connected.
Remark:
It is possible to stop the call, provided the dialling has not yet commenced, with a short press on the
end of the lighting control stalk 10.
Remarks:
• While you are on a call, the
audio source currently being
listened to is paused.
• Some ring tones on your mobile
telephone may not be recognised by the Bluetooth® system
on your vehicle. A different ring
tone will be chosen by the system.
Displays
A press on the “TEL” button displays the telephone information on
the right on your screen.
A “Telephone” symbol appears on
your display when you connect a
mobile telephone.
A “Battery” symbol appears at the
bottom of the display to indicate
the range of the mobile telephone
connected.
An “Envelope” symbol appears at
the bottom of the display to indicate
the presence of an unread SMS on
the mobile telephone connected.
A “Sound track” symbol appears
at the bottom of the display to indicate the presence of a message on
the mobile telephone connected.
HiFi system
The Hi-Fi system, custom built for your cabin, is made up of:
• A high power DSP (Digital Signal Processing) digital amplifier.
• A subwoofer bass box (30 Hz - 100 Hz).
• 8 specific loudspeakers.
• An MP3 player.
IV
Adjustment in CD or radio mode
The basic functions remain the same as those for the radio.
No extra adjustment is necessary.
However, to make the most of your Hi-Fi system, you are advised to adjust the audio functions Bass (Bass), Treble
(Treb), front/rear balance (Fad) and left/right balance (Bal) to position O, and Loudness (Loud) to position ON when
listening to a CD and position OFF when listening to the radio.
Your system also provides Dolby surround sound with the Pop, Rock and Classical ambiances.
Note: In the event of poor reception of an FM stereo signal and/or mono source, deactivate the musical ambiances.
141
F r e q u e ntly- a s k e d q u e s tion s
The table below brings together the answers to the questions that are the most frequently asked.
IV
Question
Answer
Solution
There is a discrepancy in
sound quality between the
different audio sources
(radio, CD, CD changer
etc.).
To achieve an optimum listening quality, the
audio adjustments (Volume, Bass, Treble,
Ambiance, Loudness) can be adapted to
each of the different sound sources, which
can produce audible shifts when you change
the source (radio, CD, CD changer etc.).
Check that the audio adjustments (Volume, Bass, Treble, Ambiance, Loudness) are adapted to your preferences
for each of the sources being listened
to.
Check that you have inserted the CD
the right way up in the CD player.
Check the condition of the CD: the CD
cannot be played back if it is too damaged.
The CD immediately ejects.
The CD is the wrong way up, is unplayable,
does not contain audio data or contains an
audio format that the radio cannot play back.
Check the contents if it is a burnt CD:
refer to the advice given in the chapter
on Audio System.
For reasons of poor quality, some
burnt CDs will not be played back by
the audio system.
The CD changer does not play back
DVDs.
The CD changer does not play back
MP3 CDs.
The CD player sound is
downgraded.
142
The CD is scratched or of poor quality.
The pre-set stations do not The waveband selected is not the correct
work (no sound, 87.5 Mhz one.
is displayed, etc.).
Insert only CDs of good quality and
keep them in good condition.
Press on the button BND to retrieve the
wave band (AM, FM1, FM2, FMAST)
where the stations have been memorised.
F r e q u e ntly- a s k e d q u e s tion s
Question
Traffic
Announcements
(TA) is displayed. I do not
receive any traffic information or public announcements.
Answer
Solution
IV
The particular radio station is not in the
regional traffic information network.
Change to a radio station that does
broadcast traffic information.
the RDS function to allow the
The vehicle is too distant from the transmit- Activate
to check whether a more powter, or no transmitter is present in the geo- system
erful transmitter is to be found in the
graphical area you are passing through.
geographical area.
The reception quality of
the radio station being listened to gradually deteriorates.
The environment (hills, high buildings, tunnels, underground car parks, etc.) is blocking
reception, even in RDS mode.
This phenomenon is normal and does
not imply anything wrong with the
radio.
The aerial is absent or has been damaged
(for example after going through a car wash
or in an underground car park).
Have the aerial checked by a CITROËN
dealer.
Cutting out of sound for The RDS system during this brief sound cut1 to 2 seconds in radio off is searching for a better frequency that
mode.
might offer improved reception of the station.
Deactivate the RDS function if the phenomenon occurs too frequently and
always on the same journey.
When the engine is not
running, the radio stops
after a few minutes.
When the engine is switched off, the working time for the radio depends on the battery You have to start the engine so as to
charge. The interruption is normal: the radio increase the battery charge.
goes into economy mode, cutting off in order
to save the vehicle’s battery.
The message “the audio
system is overheating”
appears on the screen.
In order to protect the audio equipment in
excessive ambient temperatures, the radio
goes into an automatic thermic protection
mode which results in a reduction in sound
volume or stopping of the CD player.
Switch off the audio system for a few
minutes in order to allow the system to
cool down.
143
B onn e t r e l e a s e
V
A
B
Bonnet
This operation should only be
performed while the vehicle is
stationary.
Open the door.
To unlock, pull release lever A.
Lift up lever B, then raise the bonnet.
Note: The panel may be hot after
the vehicle has been in use.
Bonnet stay
Unclip the stay and pivot to lodge
it in the catch indicated by a yellow
arrow.
To eliminate any risk of burns, only
handle the bonnet stay using the
protective foam.
To close
Check that nothing has been left
on top of the engine and that any
component that was moved has
been correctly repositioned.
Return the bonnet stay to its initial
position.
Lower the bonnet carefully, then let
it drop shut.
144
Check that the bonnet is
properly secured.
Do not operate the bonnet in strong winds.
1 . 8 i 1 6 v - 2 . 0 i 1 6 v E N G I N ES
1. Screen wash and headlamp wash
reservoir.
6
2. Power steering fluid or power steering and suspension fluid reservoir.
5
3
V
3. Engine coolant reservoir.
4
2
7
8
1
4. Engine oil gauge.
5. Engine oil topping-up.
6. Brake fluid reservoir.
7. Battery.
1.8i 16v
8. Air filter.
6
5
3
4
2
7
8
1
Vehicles with 2.0i 16v engines may be
fitted with metallic suspension. In this
case, the power steering oil reservoir is
different.
2.0i 16v
145
3 . 0 i V 6 E N G I N E
1. Screen wash and headlamp wash
reservoir.
V
6
2. Power steering and suspension fluid
reservoir.
3
3. Engine coolant reservoir.
5
2
1
7
8
4
4. Engine oil gauge.
5. Engine oil topping-up.
6. Brake fluid reservoir.
3.0i 16v
7. Battery.
8. Air filter.
146
H D i 11 0 - H D i 1 3 8 E N G I N ES
W ith particl e filt e r
1. Screen wash and headlamp wash
reservoir.
6
3
7
5
V
3. Engine coolant reservoir.
4
2
2. Power steering fluid or power steering and suspension fluid reservoir.
8
4. Engine oil gauge.
5. Engine oil topping-up.
1
6. Air filter.
7. Brake fluid reservoir.
8. Battery.
HDi 110
The diesel fuel circuit being under
high pressure:
ANY INTERVENTION ON THE CIRCUIT
IS PROHIBITED.
7
3
4
2
5
6
8
HDi engines are the result of
advanced technology.
Any intervention requires special
qualifications which only a
CITROËN dealer can guarantee.
1
Vehicles with HDi 138 engines may be
fitted with metallic suspension. In this
case, the power steering oil reservoir is
different.
HDi 138
147
H D i 1 7 3 - V 6 H D i 2 0 8 E N G I N ES
W ith particl e filt e r
1. Screen wash and headlamp wash
reservoir.
V
7
2. Power steering and suspension fluid
reservoir.
3
3. Engine coolant reservoir.
2
5
4
6
8
4. Engine oil gauge.
5. Engine oil topping-up.
1
6. Air filter.
7. Brake fluid reservoir.
HDi 173
8. Battery.
5
9. “+” and “-” terminals for starting with
an assisting battery.
7
3
The diesel fuel circuit being under
high pressure:
ANY INTERVENTION ON THE CIRCUIT
IS PROHIBITED.
2
4
6
1
9
148
V6 HDi 208
HDi engines are the result of
advanced technology.
Any intervention requires special
qualifications which only a
CITROËN dealer can guarantee.
Levels
These operations form part of the
normal maintenance operations
required to keep your vehicle in
good working order.
Follow the requirements in the
Maintenance Guide enclosed with
this handbook.
You will find in this Maintenance
Guide the standards, references
and characteristics of the products
to be used dependant on the driving conditions.
Air filter and cabin filter
Have
the
filters
periodically
replaced. Depending on the operating environment (e.g. dusty
atmosphere), have them replaced
twice as often.
12V battery
See “Starting with
assisting battery”.
Engine oil
Check the engine oil level
on horizontal ground with
the engine having been
switched off for at least
15 minutes.
Pull out the manual dipstick.
The
level
should
be
between the marks MIN.
and MAX. on the gauge.
It must never exceed the
maximum.
V
Power steering oil or
power steering and
suspension oil
For topping up, it is necessary to
go to a CITROËN dealer.
an
MAXI
Engine coolant
Brake fluid
The level of fluid should be
between the marks MIN.
and MAX. on the reservoir.
If the warning lamp comes on
while you are driving, stop
immediately and contact a
CITROËN dealer.
The fluid level should be
between the marks MIN. and
MAX. on the header tank.
Engine hot, wait at least 15 minutes.
Never do anything relating to
the cooling system of an engine
that is hot.
MINI
Screen wash and
headlamp wash fluid
Use
CITROËN-approved
products wherever possible.
• If opening the bonnet when the engine is hot, even if it is
stopped and the ignition is switched off, remember that the
cooling fan may operate at any moment.
• Between routine servicing visits, check the level of engine
oil frequently as well as before going on a long journey.
149
Levels
V
1
1
Topping up engine oil
Before filling, pull out the dipstick.
Check the dipstick after filling.
It must never exceed the maximum.
Screw the cap back on and close
the bonnet.
150
Radiator – coolant fluid
Checking the level and topping up
with fluid must always be done with
the engine cold.
Engine hot
Wait 15 minutes or for the temperature to be lower than 100 and then
carefully unscrew the cap so as to
allow the pressure to drop, protecting yourself with, say, a cloth.
If opening the bonnet when the engine is hot, even if it is
stopped and the ignition is switched off, remember that the
cooling fan may operate at any moment.
Topping up the coolant
The level of coolant 1 should be
between the MIN. and MAX. markings on the header tank.
Top up the level. If the top up
requires more than 1 litre, contact
a CITROËN dealer.
Make sure that the cap is back
on properly.
Note: If you need to top up the
fluid frequently, this indicates a
malfunction which you should get
checked at the earliest opportunity.
Remark: The cooling fan may
operate for around 10 minutes
after the engine has stopped.
D i e s e l inj e ction e q uipm e nt
2
V
1
3
4
Protective cover for HDi 138
engines:
Remove the protective cover by
first unclipping at 3, then 1 and 4.
Unclip at 2 by pulling towards you,
then lift up.
To refit the protective cover, firstly
clip in at 2. Lower and centre the
cover. Clip in at 3 and 4, pushing
vertically and gently from the rear.
Clip in at 1 pushing vertically.
Protective cover for HDi 110,
HDi 173 and V6 HDi 208
engines:
Draining water from the fuel
filter
Drain regularly (at each oil
change).
To drain the water, slacken the
bleed screw or the water in diesel
fuel sensor, located at the base of
the filter.
Continue until all the water has
flowed out.
Then retighten the bleed screw or
the water detection sensor.
Pull the protective cover upwards
to remove.
HDi engines are the result of advanced technology.
Any intervention requires special qualifications which only a
CITROËN dealer can guarantee.
151
D i e s e l inj e ction e q uipm e nt
V
HDi 110 engine
HDI 138 and HDi 173 engines
In the event of running out of fuel:
HDi 110, HDi 138 and HDi 173
engines with priming pump
After filling (minimum 5 litres) and
removing the protective cover,
action the manual priming pump,
until some resistance is felt.
Operate the starter motor while
depressing the accelerator pedal
slightly until the engine starts.
If the engine fails to start at the first
attempt, wait 15 seconds before
trying again.
If the engine fails to start after a
few attempts, action the priming
pump again and then try to start
the engine.
When the engine is idling, accelerate slightly to complete the bleeding of the circuit.
152
V6 HDi 208 engine with
priming pump
After adding fuel, turn the ignition
key to position M, wait for a few
seconds, then operate the starter
motor until the engine starts.
If the engine fails to start after several attempts, contact a CITROËN
dealer.
C apaciti e s
Screen wash fluid (in litres)
3.5
Screen wash and
headlamp wash fluid (in litres)
Engine type
6.15
Engine oil capacities (in litres)(1)
1.8i 16V Engine
5.0
2.0i 16V Engine
5.0
3.0i 16V Engine
4.75 / 5.0(2)
HDi 110 FAP Engine
3.75
HDi 138 FAP Engine
5.25
HDi 173 FAP Engine
5.25
V6 HDi 208 FAP Engine
(1)
(2)
V
After draining by gravity with change of oil filter.
After draining by suction with change of oil filter.
5.5 / 5.75(2)
153
12 V batt e r y
A ll e ngin e s e xc e pt V 6 H D i
V
154
Starting the engine
after disconnecting and
reconnecting the battery
1.Turn the ignition key.
2.Wait approximately 1 minute
before operating the starter in
order to allow the electronic
systems to re-initialise.
After the battery has been disconnected for a lengthy period of time,
it may be necessary to re-initialise
the following functions:
• The anti-pinch on the windows.
• The parameters of the multifunction display (date, time,
language etc).
• The Radio stations.
• The NaviDrive. See NaviDrive
instructions.
Starting the engine with an
assisting battery (except V6
HDi engine)
If the battery is discharged, it is
possible to use either a separate
emergency battery or a battery on
another vehicle.
A. Discharged battery (Under the
bonnet).
B. Assisting battery.
Check that the assisting battery
has sufficient voltage (12 V).
If you use the battery on another
vehicle, stop the engine on the
latter. The two vehicles must not
come into direct contact with each
other.
Connect the cables according to
the order indicated in the diagram.
Check that the leads are well
secured (risk of sparks).
Start the engine of the assisting vehicle. Let the engine run for
around 1 minute at a slightly accelerated idle.
Operate the starter on the vehicle
being assisted.
It is essential to follow the indicated sequence correctly.
-3
B
+1
-4
A
+2
Advice
Do not touch the leads during the
operation.
Do not lean over the batteries.
Disconnect the cables in reverse
order, making sure they do not
touch together.
For any battery replacement, contact a CITROËN dealer
12 V batt e r y
V 6 H D i e ngin e
+1
+2
A
B
-3
C
-4
Battery location and access
The battery is located in the boot
under the left hand wing trim. To
access the battery, open the flap.
Important
In the event of a battery failure,
and if the boot is closed, it is then
necessary to feed an electrical
supply to your vehicle.
Starting the engine with an
assisting battery
If the battery is discharged, it is
possible to use either a separate
emergency battery or a battery on
another vehicle.
If you use the battery on another
vehicle, stop the engine on the
latter. The two vehicles must not
come into direct contact with each
other.
Check that the assisting battery
has sufficient voltage (12 V).
Lift up the pegs to remove the front
left-hand headlamp cover.
Connect the cables according
to the order indicated in the diagram.
A Pole “+” of the broken down
vehicle (Under the red cover).
B Assisting battery.
C Pole “–” of the broken down
vehicle (Under the bonnet).
Check that the leads are well
secured (risk of sparks).
Start the engine of the assisting vehicle. Let the engine run for
around 1 minute at a slightly accelerated idle.
Operate the starter on the vehicle
being assisted.
It is essential to follow the indicated sequence correctly.
V
Advice
Do not touch the leads during the
operation.
Do not lean over the batteries.
Disconnect the cables in reverse
order, making sure they do not
touch together.
Never approach with a flame or create sparks in the vicinity of the battery (explosive gas).
The battery contains dilute sulphuric acid which is highly corrosive.
When handling batteries, always protect your face and especially your eyes.
In the event of any contact with the skin, rinse immediately with copious amounts of fresh water.
For any battery replacement, contact a CITROËN dealer.
155
Fuses
D a s hboard
FUSEBOXES
V
Dashboard fuses
The 2 fuseboxes are located below
the dashboard and under the bonnet.
To access the fuses under the
dashboard, open the glovebox and
then detach the stowage cover.
Replacing a fuse
Before replacing a fuse, you should
ascertain the cause of the fault and
have it remedied. The numbers of
the fuses are indicated on the fusebox.
Replace the fuse that has blown
with one of the same rating
(same colour).
Use the special pliers 1 placed on
the flap close to the fuseboxes.
The flap also has spare fuses
available.
Good
Fusebox A
Replacement
fuses and
pliers 1
Bad
Pliers 1
156
Fusebox C
Tabl e of fu s e s
Fusebox A
Ref.
Rating
Function
G29
-
G30
5A
Heated rear view mirrors
G31
5A
Rain and brightness sensor
G32
5A
Seat belt not fastened warning lamps
G33
5A
Electrochrome rear view mirrors
G34
20A
V
-
Sunroof (saloon)
G35
5A
G36
30A
Electric tailgate (Tourer)
G37
20A
Heated front seats
G38
30A
Driver’s electric seat
G39
30A
Passenger’s electric seat - HIFI amplifier
G40
3A
Passenger door lighting - Passenger rear view mirror adjustment
Trailer relay unit supply
Fusebox B
Ref.
G36
G37
Rating
Function
15A
6 speed automatic gearbox
5A
4 speed automatic gearbox
10A
G38
3A
G39
10A
G40
3A
Daytime-running lamps - Diagnostic socket
ESP
Hydraulic suspension
STOP switch
157
Tabl e of fu s e s
Fusebox C
V
158
Ref.
Rating
Function
F1
15A
Rear screen wipe (Tourer)
F2
30A
Locking and deadlocking relay
F3
5A
F4
10A
Automatic gearbox - Additional heater unit (Diesel) - Electrochrome rear view mirrors
F5
30A
Front window - Sun roof - Passenger door lighting - Passenger rear view mirror
adjustment
F6
30A
Rear window
F7
5A
F8
20A
Radio - CD changer - Controls at the steering wheel – Display – Tyre deflation
detection - Electric boot ECU
Airbags
Vanity mirror lighting – Glove box lighting – Interior lamps - Torch (Tourer)
F9
30A
Cigar-lighter - Front 12V socket
F10
15A
Alarm - Controls on the steering wheel, signalling and screen wipe controls
F11
15A
Low current anti-theft switch
F12
15A
Driver’s electric seat - Instrument panel - Seat belt not fastened warning lamps - Air
conditioning controls
F13
5A
Engine relay unit - Hydraulic suspension pump cut-off relay - Airbag ECU supply
F14
15A
Rain and brightness sensor - Parking assistance - Passenger’s electric seat - Trailer
relay unit - HIFI amplifier ECU - Hands-free kit - Lane Departure Warning System
F15
30A
Locking and deadlocking relay
F17
40A
Heated rear screen - Exterior heated rear view mirrors
FSH
SHUNT
CUSTOMER PARK SHUNT
Fuses
U nd e r th e bonn e t
To access the fusebox under
the bonnet, undo each screw by a
1/4 turn.
After a repair, take care to reclose
the cover.
Any repairs on the MAXI
fuses (that give additional
protection), located in the
fuseboxes, must be left to a
CITROËN dealer.
Ref.
Rating
Function
F1
20A
Engine control unit
F2
15A
Horn
F3
10A
Screen wash pump
F4
10A
Headlamp wash pump
F5
15A
Starter
F6
10A
Air flow meter - Directional headlamps - Diagnos-
F7
10A
Automatic gearbox lever lock - Power steering
F8
25A
Starter
F9
10A
Clutch switch - STOP switch
F10
30A
Starter
F11
40A
Air conditioning blower
F12
30A
Wipers
F13
40A
BSI supply (ignition on)
F14
30A
-
F15
10A
Right-hand main beam
F16
10A
Left-hand main beam
F17
15A
Right-hand dipped beam
F18
15A
Left-hand dipped beam
F19
15A
Starter
F20
10A
Starter
F21
5A
Starter
V
159
F u s e s on th e batt e r y
A ll e ngin e s e xc e pt V 6 H D i
After a repair, take care to
reclose the cover.
If the cover is not correctly positioned or not properly closed,
this could cause serious problems on your vehicle. For the
same reason, take care not to
spill any liquid in the fusebox.
V
Fuses on the battery
To access the fusebox on the battery, detach and remove the cover.
160
Ref.
Rating
Function
F6
25A
Rear 12V socket
F7
15A
Foglamps
F8
20A
Additional burner (Diesel)
F9
30A
Electric parking brake
Your vehicle’s electrical system is designed
to operate with either
standard
or
optional
equipment.
Before installing electrical equipment or accessories on your
vehicle, consult your CITROËN
dealer.
CITROËN declines all responsibility for the consequences and
costs that are caused by faults or
repairs on your vehicle resulting
from the installation of accessories that are not supplied and/or
not recommended by CITROËN
and not installed in conformity
with CITROËN requirements,
particularly when the total consumption of additional devices
exceeds 10 milliamperes.
The MAXI fuses give additional
protection to electrical systems.
Any work on them must be carried
out by a CITROËN dealer.
Fuel
Fuel quality
A label inside the filler flap tells you
which type of fuel to use.
A
Fuel flap
To open, press at the top left-hand
corner, then pull open from the
left.
Locking filler cap
Turn the key a quarter turn to lock
and unlock the filler cap.
When refuelling, place the cap on
hook A.
While you are refuelling, the
engine must be stopped and the
ignition switched off.
For a petrol engine with a catalytic converter, unleaded fuel is
compulsory.
The filler neck is narrower to
ensure that only unleaded petrol
can be put in.
When you are seeking to fill your
tank, do not persist after the
third cut-off ; this could cause
your vehicle to malfunction.
VI
The petrol engines are designed to
run on RON 95.
However,
for
better
performance (petrol engine), we recommend RON 98.
Tank capacity
The tank has a capacity of approximately 71 litres.
If you should put in fuel that is not suitable for your vehicle's
engine type, it is imperative to have the tank drained before
you start the engine again.
161
C hanging bulb s
HEADLAMPS
A
B
C
E
F
VI
D
Front headlamp unit with
Xenon bulbs (D1S)
Bulbs:
ASidelamp: W5W
B Dual-function Xenon lamp
(dipped/main): D1S
CAngular lighting: HP19
Sidelamp
1 Lift up the pegs E to remove the
cover on the headlamp.
2 Remove the protective cap F.
3 Pull the bulb holder to remove
it.
4 Replace the bulb and replace
the bulb holder.
5 Replace the protective cap F.
6 Replace the cover and fix it in
place using the pegs E.
D Daytime-running lamp: HP24
For the maintenance of the front
headlamp unit and the changing of
HP19, D1S and HP24 bulbs, contact a CITROËN dealer.
162
Front headlamps fitted with Xenon bulbs: Because of risks of electrocution, we advise you to
contact a CITROËN dealer if there is any problem.
You are advised to change the D1S bulbs at the same time, if one of them has failed.
C hanging bulb s
HEADLAMPS
A
B
C
G
F
D
VI
E
HEADLAMP UNIT
Bulbs:
AMain beam: H1
BSidelamp: W5W
C Dipped beam: H7
D Bend lighting: H7
E Daytime-running lamp: HP24
For the maintenance of the front
headlamp unit and the changing of
HP24 bulbs, contact a CITROËN
dealer.
Main beam
1 Lift up the pegs F to remove the
cover on the headlamp.
2 Remove the protective cap G.
3 Disengage the retaining spring.
4 Remove the bulb and replace it,
paying attention to the direction
of fitting.
5 Replace the retaining spring.
6 Replace the protective cap G.
7 Replace the cover and fix it in
place using the pegs F.
Sidelamp
1 Lift up the pegs F to remove the
cover on the headlamp.
2 Remove the protective cap G.
3 Pull the bulb holder to remove
it.
4 Replace the bulb and replace
the bulb holder.
5 Replace the protective cap G.
6 Replace the cover and fix it in
place using the pegs F.
Halogen bulbs must not be changed until they have been off for a few minutes (risk of serious
burns).
Do not touch the bulb directly with your fingers, use a lint-free cloth.
It is essential that only anti-U.V. type bulbs are used in order not to damage the headlamp.
163
C hanging bulb s
HEADLAMPS
VI
A
H
Dipped beam
1 Lift up the pegs F to remove the
cover on the headlamp.
2 Remove the protective cap H.
3 Disconnect the connector by
pressing it between the thumb
and index finger.
4 Free the bulb from its two metal
clamps.
5 Take out the bulb.
6 Replace the bulb, exerting a
slight axial force.
7 Reconnect the connector, until
it is all the way in.
8 Replace the protective cap H.
9 Replace the cover and fix it in
place using the pegs F.
164
I
Bend lighting
1 Lift up the pegs F to remove the
cover on the headlamp.
2 Remove the protective cap I.
3 Disconnect the connector by
pressing it between the thumb and
index finger.
4 Free the bulb from its two metal
clamps.
5 Take out the bulb.
6 Replace the bulb, exerting a
slight axial force.
7 Reconnect the connector, until
it is all the way in.
8 Replace the protective cap I.
9 Replace the cover and fix it in
place using the pegs F.
Front direction indicator
1 Remove the fixing screw of
cover A using a torx tool, tip the
cover over and remove.
2 Remove the fixing screw of
lamp B using a torx tool and pull
the headlamp unit to remove it
from the bumper.
3 Detach the bulb C by pressing
on bars 1 and 2.
4 Disconnect the connector (pull
whilst pressing on the grey
tongue using a flat screwdriver).
5 Replace the bulb.
6 Connect the connector (push the
grey tongue in well).
7 Replace the headlamp unit in the
bumper.
8 Screw the headlamp unit in.
9 Position the cover using its
guides and screw in.
Bulbs: HP24W
C hanging bulb s
HEADLAMPS
VI
B
D
C
1
2
Front foglamp
1 Remove the fixing screw of
cover A using a torx tool, tip the
cover over and remove.
2 Remove the fixing screw of
lamp B using a torx tool and pull
the headlamp unit to remove it
from the bumper.
3 Disconnect the connector D.
4 Remove the bulb by performing
a quarter of a turn.
6 Connect the connector D.
7 Replace the headlamp unit in
the bumper.
8 Screw the headlamp unit in.
Side repeater
The side repeater is sealed.
If the bulb is faulty, replace the side
repeater.
Contact a CITROËN dealer.
9 Position the cover using its
guides and screw in.
Bulbs: H8
5 Replace the bulb.
When replacing, be
careful not to pinch the
electrical cables.
165
C hanging bulb s
REAR LAMPS (SALOON)
H
VI
A
B
C
E
G
D
F
Rear lamp unit
Identify the failed bulb.
Bulbs:
AStop-lamps and sidelamps:
P 21 W / 5 W
BSidelamp: R 5 W
CReversing lamp: H 21 W
D Foglamp: H 21 W
E Direction indicator: P 21 W
166
Rear lamp on boot
1 Open the boot.
2 Using a flat screwdriver, remove
the 3 clips which fix the trim in
the lamp area.
3 Partially remove the trim F.
4 Disconnect the connector G.
5 Detach the bulb holder H.
6 Replace the bulb.
7 Replace the bulb holder H.
8 Connect the connector G.
9 Replace and fix the trim F with
its clips.
In some climatic conditions,
mist may appear on the
headlamp / indicator lenses.
This is normal and will
disappear (e.g. after the
lamps have been on for a
few minutes). If not, contact
a CITROËN dealer.
C hanging bulb s
REAR LAMPS (SALOON)
VI
B
A
C
D
5 Detach the bulb holder D.
6 Replace the bulb.
7 Replace the bulb holder D.
8 Place the lamp in its housing.
9 Screw in the 2 fixings C.
10Connect connector B.
11 Refit the trim A.
Rear lamp on wing
1 Remove the lateral boot trim
flap A. To do so, pull it towards
the inside of the boot, then pull
it upwards.
2 Disconnect connector B.
Note: You can use the spare wheel
jack handle to screw or unscrew
the fixings C.
3 Unscrew the 2 fixings C.
4 Remove the lamp from its housing.
167
C hanging bulb s
R E A R L A M P S ( T our e r )
H
VI
B
A
E
C
G
D
Rear lamp unit
Identify the failed bulb.
Bulbs:
AStop-lamp and sidelamp :
P 21 W / 5 W
BSidelamp : R 5 W
CReversing lamp : H 21 W
D Foglamp : H 21 W
E Direction indicator: P 21 W
F
Rear lamp on boot
1 Open the boot.
2 Using a flat screwdriver, remove
the 3 clips which fix the trim in
the lamp area.
3 Partially remove the trim F.
4 Disconnect the connector G.
5 Detach the bulb holder H.
6 Replace the bulb.
7 Replace the bulb holder H.
8 Connect the connector G.
9 Replace and fix the trim F with
its clips.
168
In some climatic conditions,
mist may appear on the
headlamp / indicator lenses.
This is normal and will
disappear (e.g. after the
lamps have been on for a
few minutes). If not, contact
a CITROËN dealer.
C hanging bulb s
R E A R L A M P S ( T our e r )
VI
B
1
2
A
C
D
6 Detach the bulb holder D.
7 Replace the faulty bumb.
1
8 Replace the bulb holder D.
9 Place the lamp in its housing.
10 Screw in the fixing screw C.
A
11 Connect the connector B.
2
12 Refit the trim A.
Note : You can use the spare wheel
jack handle to screw or unscrew
the fixing screw C.
Rear lamp on wing
Remove the lateral boot trim A.
To do so :
1 Pull it towards towards the
inside of the boot.
2 Pull it upwards.
3 Disconnect the connector B.
4 Unscrew the fixing screw C.
5 Remove
housing.
the
lamp
from
its
169
C hanging bulb s
REAR LAMPS
VI
Third stoplamp
The third stoplamp uses diodes
which cannot be replaced.
In case of malfunction, contact
a CITROËN dealer.
170
Number plate
1 Using a flat screwdriver, detach
the transparent cover by levering it into the notch provided.
2 Lift up and pull the transparent
cover.
3 Using a small flat screwdriver,
remove the faulty bulb.
4 Fit the new bulb by firstly placing the angled base on the axis
of the clips, then press the bulb
in to insert.
5 Refit the transparent cover by
inserting it from the edge opposite the notch, then press on the
edge of the transparent cover.
Bulb: W 5W
After each operation,
check that the lamps work.
C hanging bulb s
INTERIOR LAMPS
VI
Interior lamps
Unclip the transparent cover of the
interior lamp to reach the bulb.
Boot lamp
To change the bulb, detach the
cover and use a bulb W 5 W.
Bulb: W 5W
Floor lighting
To change the bulb for the floor
lighting (front or rear): Detach the
cover. Use a bulb W 5 W.
Spotlamp
Detach the cover.
To access the bulb, detach if necessary the partition of the affected
spotlamp.
Pavement lighting
To change the bulb for the door sill
lighting: Detach the cover. Use a
bulb W 5 W.
Glovebox
To change the glovebox bulb,
detach the cover and use a W 5 W
bulb.
Rear reading lamps (Tourer)
Detach the cover of the reading
lamp to access the bulb.
Bulb: W 5W
171
Saf e t y r e comm e ndation s
Towing (Boat, caravan, etc.)
VI
Towbar
We recommend that you use
CITROËN towbars and harnesses
which have been tested and
approved during the design of your
vehicle, and that these devices are
fitted by a CITROËN dealer.
If a device is fitted outside of the
CITROËN network, it must be carried out using the electrical connections fitted at the rear of your vehicle
and following the recommendations
of the manufacturer.
172
If you are climbing a steep gradient
and the engine gets excessively
hot, certain functions become unavailable (e.g. sequential control of
the automatic gearbox, the air conditioning).
If you are towing with a device not
approved by the CITROËN network,
you must deactivate parking assistance using the button on the dashboard. See “Parking assistance”.
It is recommended that you remove
the towing ball, so that it does not
interfere with the functioning of the
proximity sensors, when you are
not using a trailer.
Roof bars
For your safety and to avoid damage to the roof, you must use roof
bars that are tested and approved
by AUTOMOBILES CITROËN.
Recommendations:
• Spread the load evenly, avoiding overloading on one side.
• Position the heaviest weight as
low down as possible.
• Tie the load down securely and
add warning signs if it is protruding.
• Drive conservatively, as the
vehicle will be more vulnerable
to side winds.
The stability of your vehicle may
be altered.
• Remove the roof rack or roof
bars when you are not using
them.
It is essential to install a CITROËN approved electronic unit
when having a towbar fitted, in order to prevent any risk of
malfunction or damage (risk of fire).
If you are towing another vehicle, the latter must be freewheeling (gearbox in neutral).
Do not exceed the maximum permitted load.
For the maximum distributed load on the roof bars: see the chapter
“General”.
P unctur e kit
A
Puncture kit
The puncture repair kit is located in
the boot, underneath the tool kit.
The puncture repair kit is a complete system including a compressor and a setting product.
1
Using the puncture repair kit
1 Remove the sticker found in the
kit, then stick it on the steering
wheel to remind you that you
are driving with a wheel that is
only fit for temporary use and
that your speed is therefore limited.
2 Connect the flask 1 to the valve
of the tyre to be repaired.
3 Connect the electric cable to
one of the vehicle's 12V sockets.
4 With the engine running, start
the compressor by pressing on
button A until the tyre pressure
reaches 2,0 bars. If you cannot
reach a pressure of 2 bars, the
tyre is not repairable.
5 Remove and store the compressor.
6 Drive off immediately, for a few
miles at reduced speed, to allow
the puncture repair to set.
7 Adjust the tyre pressure using
the compressor according to
the recommendations for the
vehicle, and check that there
is no air escaping (no loss of
pressure). If you cannot reach
a pressure of 2 bars, the tyre is
not repairable.
8 Do not exceed 110 km/h (68 mph).
The tyre must be examined,
then repaired or replaced as
soon as possible by a professional.
Warning, the flask of puncture repair gel contains ethylene-glycol, a product that is toxic if ingested
and irritating for the eyes.
Keep out of the reach of children.
After use, do not dispose of the flask in the natural environment, but return it to a CITROËN dealer
or to a recognised recovery facility.
This repair kit is available from a CITROËN dealer.
VI
173
C hanging a wh e e l
1
VI
2
3
Access to the spare wheel
To access the spare wheel
1 Lift up the boot floor using the
strap (saloon) or the retractable
handle (Tourer).
2 Fold back the boot carpet
(saloon).
3 Attach the hook to the upper
section of the boot (in the middle
of the boot pillar).
4 To remove the spare wheel,
detach the strap then push the
wheel forwards so as to be able
to lift it.
174
To reposition the spare wheel
To put the spare wheel back in the
boot
1 Position the spare wheel flat in
the boot, then pull it towards
you.
2 Next place the toolbox inside the
wheel, then secure the assembly with the belt.
3 Release the strap to return the
boot floor to its initial position.
Tyre pressures
The tyre pressure is indicated on
the label located on the left-hand
door centre pillar. On this label, the
pressures are specified, according
to the vehicle load.
5
6
4
Tools
The tools are to be found in a protective holder inside the spare
wheel. Pull back the retaining strap
to have access.
1 Handle
2 Jack
3 Tool for the removal/refitting of
bolt protectors
4 Centring guide
5 Towing eye
6 Moveable chock
C hanging a wh e e l
Removal
7 Slacken the wheel bolts.
8 Continue to extend the jack until
the wheel is a few centimetres
off the ground.
9 Undo the bolts, remove the
wheel.
1 Park the vehicle on stable,
firm ground that is not slippery.
Apply the parking brake.
2 If your vehicle is equipped with
“Hydractive III+” suspension,
with the engine running at idle,
adjust the ground clearance to
its maximum height. See chapter “Hydractive III+ Suspension”.
3 Switch off the ignition and
engage first gear or reverse
gear depending on any slope
(for a vehicle with automatic
gearbox, select position P).
4 If your vehicle is fitted with
“Hydractive III+” suspension,
position the chock, whichever
direction the gradient may be
in, in front of the front wheel
diametrically opposite to the
one to be replaced.
5 Position the jack at one of the
four jacking-points provided
on the subframe close to the
wheels, then use the handle to
unwind the jack until it reaches
the ground.
3
6 Remove the protector
each bolt using tool 3.
from
VI
Before positioning the
jack :
adjust
the
- Always
vehicle’s
ground
clearance to the “maximum
height” position and retain
this adjustment for as long
as the jack is under the vehicle (do not use the hydraulic
adjustments).
- Immobilise your vehicle on
horizontal, stable and nonslippery ground.
- Ensure that any passengers
have left the vehicle and are
in a safe place.
Never get underneath the vehicle if it is supported only by
the jack.
The jack and all of the tools
are specific to your vehicle.
Do not use them for any other
applications.
Have the original wheel repaired
and refitted as soon as possible.
175
C hanging a wh e e l
Refitting a wheel
VI
Spare wheel
Your vehicle may be fitted with a
different spare wheel to those on
the vehicle. When fitting the spare
wheel, it is normal to notice that the
wheel bolt washers do not come
into contact with the wheel rim.
The spare wheel is secured by the
conical tapering of the wheel bolt’s
shaft.
When refitting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good
condition.
176
1 Fit the wheel on the hub,
using the centring guide. Make
sure that the contact surface
between the hub and the wheel
is clean.
2 Screw in the bolts but do not
fully tighten them.
3 Lower the jack and remove it.
4 Tighten the wheel bolts, using
the wheelbrace.
5 Refit the protectors on the
bolts.
6 Return the ground clearance to
the normal position. See chapter “Hydractive III+ Suspension”.
7 Ensure the tyre pressure is correct (see “Vehicle identification”) and have the balancing
checked.
Wheel equipped with
deflation detection sensor
Such wheels have tyre pressure
sensors. It is essential to have
repairs carried out by a CITROËN
dealer.
Anti-theft bolts
Each wheel is equipped with one
anti-theft bolt.
To remove it
1 Remove
tool 3.
the
protector
using
2 Use the anti-theft socket with
the handle.
If your vehicle is fitted with a spare wheel of a different size to
those on the vehicle, you must not exceed 80 km/h (50 mph)
whilst using the spare wheel.
The wheel bolts are specific to the type of wheel.
If the type of wheel is changed, check with your CITROËN dealer
that the wheel bolts are compatible with the new wheels.
Note: take care to note down the code number engraved on the
head of the anti-theft bolt socket. This will enable you to obtain
replacement anti-theft bolt sockets from a dealership.
T owing – L ifting
VI
Towing with wheels on
the ground
Towing eye fixings are located at
the front and at the rear of the vehicle.
Detach the cover:
• For the front cover, lever with
a screwdriver at the top of the
cover.
• For the rear cover, press:
- On the right hand side
(saloon),
- On the bottom (Tourer).
The ignition key must be in position M to retain steering.
Use a bar with attachments to the
towing eyes as above.
The towing eye is removable, to be
stowed in the jack protection box
inside the spare wheel.
Advice
Towing at low speed over a very
short distance is authorised in
exceptional cases depending on
the regulations in force.
Otherwise, it is necessary to
have your vehicle transported
on a recovery truck.
It is essential to check that the
electric parking brake is released.
Requirement — Towing
with automatic
gearbox
Place the selector on position N
(neutral).
When the engine is not
running, the steering
and the braking are no
longer assisted.
If you are towing another vehicle, the latter must be freewheeling (gearbox in neutral).
Towing with either the front or
the rear of the vehicle raised, or
in “minimum height” position,
is forbidden.
177
VERY COLD PROTECTION
VI
Moveable device which prevents
the intake of snow particles, which
could obstruct the air filter.
2
3
1
2
DIESEL ENGINE HDi 173 FAP
Normal situation
The shutter 2 is in a horizontal
position in the air duct 3.
1
3
Snow situation
Push and rotate the knob 1 by 90 °
in the direction of the arrow in order
to position the shutter 2 in a vertical position in the air duct 3.
2
DIESEL ENGINE
V6 HDi 208 FAP
Snow situation
Slide the deflector 1 into the air
duct 2 and clip in.
Note : To return to the normal situation, push the knob 1 then rotate
in the opposite direction.
178
It is essential to remove the very cold protection:
• When the outside temperature exceeds 10 °C.
• When driving at speeds of over 120 km/h (approximately
75 mph).
SNOW GUARD
SNOW GUARD
Moveable device which prevents
the accumulation of snow by the
radiator cooling fan.
VI
Fitting
• Bring the 2 sections of the snow
guard up to the upper and lower
sections of the front bumper.
• Press on the surround to clip in
one by one the fixing clips.
Before fitting
After fitting
Remove
• Using a screwdriver, lift it up to
detach each fixing clip one by
one.
It is essential to remove the snow guard:
• When the outside temperature exceeds 10 °C.
• When towing.
• When driving at speeds of over 120 km/h (approximately
75 mph).
179
G e n e ral
ENGINE TYPE - SALOON
VII
1.8i 16V
BVM
2.0i 16V
BVM
2.0i 16V
BVA
Fuel tank capacity
3.0i V6
BVA
HDi 110
HDi 138
HDi 138
HDi 173 V6 HDi 208
BVM FAP BVM FAP BVA FAP BVM FAP BVA FAP
Approximately 71 litres
Diesel fuel
Fuels to be used
Unleaded petrol RON 95 - RON 98
French fiscal rating
8
9
9
14
6
8
9
10
13
Power (kW)
92
103
103
155
80
100
100
125
150
Turning circle between walls (in metres)
12
12
12
12.2
12
12
12
12.2
12.2
200
(124)
210
(131)
205
(127)
224
(139)
191 (119)
204
(127)
201
(125)
219
(136)
224 (139)
Unladen weight
1510
1521
1583
1725
1503
1608
1658
1729
1766
Gross vehicle weight (MTAC)
2015
2063
2090
2230
2040
2155
2190
2216
2310
Maximum weight on rear axle
960
960
960
1010
960
970
970
980
1045
Gross train weight (MTRA)(1)
3315
3563
3590
3630
3140
3755
3490
3816
3710
1300
(1530*)
1500
(1720*)
1500
(1720*)
1400
(1650*)
1100
(1370*)
1600
(1820*)
1300
(1560*)
1600
(1820*)
1400
(1690*)
1700
1800
1800
1400
1100
1800
1300
1800
1400
62
69
69
66
55
73
63
73
68
Calculated maximum speed in km/h
(mph) (In the highest gear)
Weights (kg)
Gross trailer weight (within the Gross
Train Weight limit)
8% < incline ≤ 12%
incline ≤ 8%
Gross trailer weight (without brakes)
Trailer nose weight
Maximum roof rack load
180
750
80
(*) Weight transfer: The braked towing weight can be increased. It is possible, when the towing vehicle is within the gross vehicle weight, to
transfer weight allowance from the trailer. In all cases, do not exceed the trailer and Gross train weight values indicated.
(1) In the case of a towing vehicle, the maximum speed it limited to 100 km/h (62 mph) (observe the current laws in your country).
G e n e ral
ENGINE TYPE - TOURER
1.8i 16V
BVM
2.0i 16V
BVM
2.0i 16V
BVA
Fuel tank capacity
3.0i V6
BVA
HDi 110 HDi 138 HDi 138 HDi 173 V6 HDi 208
BVM FAP BVM FAP BVA FAP BVM FAP BVA FAP
Approximately 71 litres
Diesel fuel
Fuels to be used
Unleaded petrol RON 95 - RON 98
French fiscal rating
8
9
9
14
6
8
9
10
13
Power (kW)
92
103
103
155
80
100
100
125
150
Turning circle between walls (in metres)
12
12
12
12.2
12
12
12
12.2
12.2
196
(122)
206
(128)
202
(126)
222
(138)
188 (117)
200
(124)
198
(123)
216
(134)
222 (138)
Unladen weight
1549
1578
1619
1761
1537
1655
1695
1765
1802
Gross vehicle weight (MTAC)
2154
2183
2224
2366
2178
2276
2326
2352
2373
Maximum weight on rear axle
1130
1130
1130
1130
1130
1130
1130
1130
1130
Gross train weight (MTRA)
3454
3683
3724
3666
3178
3776
3526
3952
3676
1300
(1600*)
1500
(1790*)
1500
(1800*)
1300
(1600*)
1000
(1300*)
1500
(1800*)
1200
(1500*)
1600
(1900*)
1300
(1600*)
1700
1800
1800
1300
1000
1800
1200
1800
1300
64
72
72
68
52
72
60
77
64
Calculated maximum speed in km/h
(mph) (In the highest gear)
VII
Weights (kg)
(1)
Gross trailer weight (within the Gross
Train Weight limit)
8% < incline ≤ 12%
incline ≤ 8%
Gross trailer weight (without brakes)
Trailer nose weight
Maximum roof rack load
750
80
(*) Weight transfer: The braked towing weight can be increased. It is possible, when the towing vehicle is within the gross vehicle weight, to
transfer weight allowance from the trailer. In all cases, do not exceed the trailer and Gross train weight values indicated.
(1) In the case of a towing vehicle, the maximum speed it limited to 100 km/h (62 mph) (observe the current laws in your country).
181
F u e l con s umption
( in litr e s / 1 0 0 km ( mil e s p e r gallon ) )
3.0i V6
HDi 110
FAP
HDi 173
FAP
V6 HDi 208
FAP
BVA
BVA
BVM
BVM
BVA
BVM
BVA
12
12.7
15.6
7.3
7.9
9.9
8.8
11.8
257
285
303
371
193
209
262
234
315
Extra urban
6.2
6.3
6.7
7.5
4.7
4.9
5.5
5.2
6.4
CO2 emissions (g/km)
148
151
160
180
125
129
146
138
171
Combined
7.9
8.4
8.9
10.5
5.6
6
7.1
6.5
8.4
CO2 emissions (g/km)
188
198
212
248
149
157
189
172
223
Engine type
1.8i 16V
SALOON
BVM
BVM
Urban
10.8
CO2 emissions (g/km)
VII
2.0i 16V
HDi 138
FAP
These consumption figures are established according to Directive 80/1268/CEE. Fuel consumption can vary depending on style of driving, traffic conditions, weather conditions, vehicle load, how the vehicle has been maintained and
on use of accessories.
The fuel consumption figures quoted here are correct at time of going to press.
FAP: Diesel particulate filter system.
BVM: Manual gearbox.
BVA: Automatic gearbox.
182
F u e l con s umption
( in litr e s / 1 0 0 km ( mil e s p e r gallon ) )
3.0i V6
HDi 110
FAP
HDi 173
FAP
V6 HDi 208
FAP
BVA
BVA
BVM
BVM
BVA
BVM
BVA
12.1
12.8
15.7
7.4
8
10
8.9
11.9
266
287
305
373
196
212
265
236
317
Extra urban
6.3
6.4
6.8
7.6
4.5
5
5.6
5.3
6.5
CO2 emissions (g/km)
151
153
163
182
127
132
149
141
173
Combined
8.1
8.5
9
10.6
5.7
6.1
7.2
6.6
8.5
CO2 emissions (g/km)
192
200
214
250
150
160
191
175
225
Engine type
1.8i 16V
2.0i 16V
Tourer
BVM
BVM
Urban
11.1
CO2 emissions (g/km)
HDi 138
FAP
VII
These consumption figures are established according to Directive 80/1268/CEE. Fuel consumption can vary depending on style of driving, traffic conditions, weather conditions, vehicle load, how the vehicle has been maintained and
on use of accessories.
The fuel consumption figures quoted here are correct at time of going to press.
FAP: Diesel particulate filter system.
BVM: Manual gearbox.
BVA: Automatic gearbox.
183
D im e n s ion s
(IN MM)
VII
SALOON
A
2 815
B
1 054
C
910
D
4 779
E
1 586
F
2 096
G
1 557
H
1 860
I*
1 451
B
A
C
D
I
* Without roof bars.
184
E
G
F
H
D im e n s ion s
(IN MM)
VII
C
B
A
SALOON
E
D
F
A
1 030
B
1 115
C
566
D
504
E
1 040
F
1 705
185
D im e n s ion s
(IN MM)
VII
Tourer
A
2 815
B
1 054
C
959
D
4 829
E
1 586
F
2 096
G
1 557
H
1 860
I*
1 479
B
A
C
D
I
* Without roof bars.
186
E
G
F
H
D im e n s ion s
(IN MM)
VII
B
A
Tourer
D
C
E
F
A
1 060
B
1 115
C
510
D
851
E
1 058
F
1 723
187
V e hicl e id e ntification
VII
C
B
D
A
A Chassis number plate
On the left hand door centre
pillar.
1.EU type approval number.
2.Vehicle identification No. (VIN).
3.Gross vehicle weight.
4.Gross train weight.
5.Maximum weight on front axle.
6.Maximum weight on rear axle.
B Body serial number
CSerial number on dashboard
D Paint colour code and tyre
reference
Tyre pressure
On the left hand door centre
pillar.
C
B
A
D
1
2
3
4
5
6
A
188
The vehicle type and the identification number are also indicated on the registration document.
All CITROËN original replacement parts are available exclusively within the dealer network.
For your safety and in order to remain within the terms of the guarantee, you are advised to use only CITROËN
replacement parts.
iNDEX
11.8i 16v Engine...................145
12 V battery...... 154 - 155 - XIV
3 3.0i V6 Engine.....................146
A Access to the vehicle.... 92 - 94
Accessories
socket 12V.........................118
Adjusting the air distribution
(Dual-zone)........................101
Adjusting the air distribution
(Monozone).........................98
Adjusting the air flow
(Dual-zone)........................101
Adjusting the air flow
(Monozone).........................98
Adjusting the rear
view mirrors.........................58
Adjusting the seat
belt height............................52
Adjusting the steering
column.................................52
Adjusting the temperature
(Dual-zone)........................100
Adjusting the temperature
(Monozone).........................97
Advice on driving.................... X
Air conditioned
glove box................... 95 - 117
Air filter................................149
Air recirculation Entry of air from outside
(Dual-zone).............. 101 - 102
Air recirculation Entry of air from outside
(Monozone).........................99
Airbags.................. 108 - VVII
A Ambient centre console
lighting...............................115
Ambient dashboard
lighting...............................115
Angled lighting.......................48
Anti-intrusion alarm....... 25 - 26
Anti-intrusion security............92
Anti-pinch.................. 124 - 125
Anti-theft bolts.....................176
Audio adjustments...............130
Automatic activation
of alarm (depending
on destination).....................26
Automatic
air conditioning...........95102
Automatic
gearbox................ 28 - 6467
Automatic headlamp
lighting.................................45
B Bend lighting..........................47
Bluetooth®..................138140
Bonnet release....................144
Boot (saloon).......................120
Boot (Tourer).......................121
Boot access.........................107
Brake fluid...........................149
Brakes...................................74
Braking system.................... XIII
Brightness sensor..................95
Button controls....................128
C Capacities............................153
Cargo net (Tourer)...............123
Catalytic converter..............XVII
CD..............................135136
CD changer............... 126 - 127
189
C Changing a fuse..................156
Changing a wheel......174176
Changing bulbs..........162171
Chassis no. plate.................188
Checks................................149
Child restraints........... 110113
Child
safety.........109113 - VIIIIX
Child
seats.......... 110113 - VIIIIX
Control panel............. 126 - 127
Coolant temperature
indicator...............................41
Courtesy lighting..................116
Cruise control................ 68 - 69
D Date............................... 60 - 62
Daytime lamps.......................46
Deactivation of the alarm
using the key............... 25 - 26
Diesel injection
equipment................ 151 - 152
Diesel particle filter................33
Diesel particulate
filter system.........................33
Dimensions
(saloon)................... 184 - 185
Dimensions
(Tourer).................... 186 - 187
Direction indicators................44
Display (Dual-zone).............100
Display (Monozone)..............97
Door opening controls
lighting...............................115
Driver’s oddments tray........117
Driving position........................II
Driving positions....................56
iNDEX
190
D DUAL-ZONE control
panel..................................100
Dust/pollen filter.....................96
Dynamic emergency
braking.................................78
EEconomy mode.....................27
Electric parking brake.....7581
Electrical accessories........XVIII
Emergency unlocking............78
Emergency unlocking
of the boot...........................93
Engine 2.0i 16V...................145
Engine coolant.....................149
Engine HDi 110...................147
Engine HDi 138...................147
Engine oil................... 149 - 150
Engine oil level indicator.......36
Engine oil temperature
gauge..................................41
ESP.......................................84
F Fixed central controls
steering wheel............. 42 - 43
Flap for transport of long
objects...............................106
Floor lighting........................116
Floor mat.............................118
Foglamps...............................46
Foldable benchseat.............107
Fold-back of door mirrors......58
Frequently-asked
questions................. 142 - 143
Front armrest.......................117
Front cup-holder..................117
Front demisting - deicing
(Dual-zone)........................102
F Front demisting - deicing
(Monozone).........................98
Front door storage pockets
automatic lighting..............116
Front passenger’s airbag
deactivation.......................108
Front seats.....................5355
Fuel.....................................161
Fuel consumption
(in litres/100 km)...... 182 - 183
Fuel gauge............................41
Fuel quality..........................161
Fuses..........................156160
GGeneral audio functions......130
General
information............... 180 - 181
Guide-me-home lighting........46
H Hazard lamps........................44
HDi 173 Engine...................148
Heated seats.........................55
HiFi system..........................141
Hill start assist.......................82
“Hydractive III+”
suspension...................8586
I
Identification........................188
Ignition...................................27
Instrument panel..... 2933 - 41
Instrument panel
screen...........................3440
Interior comfort........... 117119
Interior lamps.......................114
Interior lighting............ 114116
Interior rear view mirror.........57
I ISOFIX anchoring
points........................110 - 112
ISOFIX child seats..... 110113
Isofix fixings................ 110 - 111
K Key........................................24
L Lane Departure Warning
System........................ 21 - 87
Levels (engine)....................149
Levels (temperature)...........150
Lighting controls............ 45 - 46
Loads and towing................XVI
Locking/unlocking from
the inside.............................92
Locking/unlocking
the doors..................... 92 - 93
Log of alerts..........................36
Luggage-cover
blind (Tourer) ....................122
MMaintenance..... 149 - 156160
Maintenance
indicator....................... 37 - 38
Manual gearbox............. 28 - 63
Manual headlamp
adjustment...........................45
Manual parking brake............83
Massage function..................55
Memorisation of driver’s
adjustments.........................56
MONOZONE control panel...97
MP3 CD . ............................136
Multifunction display.......5962
iNDEX
N NaviDrive.............................126
Navigation.............................35
OOil gauge.............................149
Opening the boot (saloon).....93
Opening the boot (Tourer).....94
Operating anomalies..... 80 - 81
Operating the alarm...... 25 - 26
P Paint colour code................188
Paint colour reference.........188
Panoramic sunroof
(Tourer)..............................125
Parking
assistance............21 - 88 - 89
Parking space
sensor...................21 - 90 - 91
Passenger compartment
air filter.................................96
Pavement lighting................116
Personalisation/
Configuration................5962
Power steering oil................149
Programmable
heating......................103105
Puncture repair kit...............173
Punctures...................... XI - XV
R Radiator - coolant................149
Radio..........................127143
RDS audio compact disc
system...............................127
RDS system.............. 133 - 134
Rear armrest (storage)........118
Rear blind (saloon)..............119
Rear cup-holder...................118
R Rear demisting deicing (Dual-zone)...........102
Rear demisting deicing (Monozone).............98
Rear door blinds..................119
Rear head restraints............106
Rear lamps
(saloon)..........166 - 167 - 170
Rear lamps
(Tourer)...........168 - 169 - 170
Rear passenger
air vents...............................95
Rear reading lamps
(Tourer)..............................114
Rear seats................. 106 - 107
Rear view mirrors.......... 57 - 58
Recycling and
the environment...............XXIII
Refitting a wheel..................176
Remote control.............. 22 - 23
Removing a wheel...............175
Replacing a fuse.................156
Roof bars.............................172
Running in.........................XVIII
SSafety recommendations................ 172 - XIXII
Screen wash.................. 49 - 50
Screen wash fluid................149
Screen wipe................... 49 - 50
Seat belts........................ IIIIV
Selection of doors/boot.........92
Set of roof bars....................172
Signalling........................4446
Snow chains.................. X - XIX
Snow guard.........................179
Soft air conditioning diffusion
grille.....................................95
191
SSound signal for headlamps
left on...................................46
Spare wheel.............. 174 - 176
Speed limiter................. 70 - 71
Sport mode............................85
Spotlamps...........................114
Starter....................................27
Starting..................................28
Starting the engine................28
Starting the engine with an
assisting battery...... 154 - 155
Steering lock..........................27
Steering wheel mounted
controls...............42 - 43 - 129
Stop imperative.....................31
Sun visor.............................119
Sunroof (saloon)..................124
Suspension oil.....................149
Suspension with electronically
controlled springing and
damping........................8586
T Telematics......................6162
Time............................... 60 - 62
Tools....................................174
Towbar.................................172
Towing.................................172
Towing - Lifting....................177
Trip computer.................3435
Tyre deflation
detection...................... 72 - 73
Tyre maintenance.................XV
Tyre pressures... 174 - 188 - XV
Tyres.................. 174 - 188 - XV
U User Precautions......................I
192
V V6 HDi 208 Engine..............148
Vehicle parameters................40
Very cold protection.............178
Volumetric detection
deactivation.........................26
WWarning lamps................3032
Windows................................51
Winter precautions..............XIX
Wipers........................... 49 - 50
X Xenon bulbs........................162
Xenon dual function
directional headlamps.........48
iNDEX