Cisco 11500 Series
Content Services Switch
Hardware Installation Guide
Software Version 7.10
December, 2002
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Customer Order Number: DOC-7813884=
Text Part Number: 78-13884-03
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR
THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION
PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO
LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate
radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television
reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in
part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class
A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct
any interference to radio or television communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco
equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by
using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television
or radio are on circuits controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as
part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE
PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
CCIP, the Cisco Arrow logo, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, iQ
Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and
Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, The Fastest Way to
Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE,
CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital,
the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient,
IOS, IP/TV, LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar,
SlideCast, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (0208R)
Cisco 11500 Series Content Services Switch Hardware Installation Guide
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.
C O N T E N T S
About This Guide xvii
Audience xvii
How to Use This Guide xviii
Related Documentation xix
Symbols and Conventions xxi
Obtaining Documentation xxiv
World Wide Web xxiv
Documentation CD-ROM xxv
Ordering Documentation xxv
Documentation Feedback xxv
Obtaining Technical Assistance xxvi
Cisco.com xxvi
Technical Assistance Center xxvi
Cisco TAC Web Site xxvii
Cisco TAC Escalation Center xxviii
CHAPTER
1
Unpacking and Installing the CSS 1-1
Site Requirements 1-2
Safety Guidelines 1-2
Chassis-Lifting Guidelines for the CSS 11503 and CSS 11506 1-3
Electrical Safety 1-4
Specifications for Cisco 11500 Series Power Supplies 1-6
Power Guidelines for DC Systems (CSS 11503 and CSS 11506) 1-7
Required Tools and Equipment 1-7
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
v
Contents
Shipment Contents 1-8
Unpacking the CSS 1-9
Unpacking the CSS 11501 1-9
Unpacking the CSS 11503 or CSS 11506 1-9
If the Product is Damaged 1-10
Preinstallation Requirements 1-11
Installing the CSS 11501 1-12
Installing a CSS 11501 as a Freestanding Unit 1-12
Installing a CSS 11501 as a Rackmounted Unit 1-13
Installing the CSS 11503 1-14
Installing a CSS 11503 as a Freestanding Unit 1-14
Installing a CSS 11503 as a Rackmounted Unit 1-15
Installing the CSS 11506 1-17
Mid-Mounting the CSS 11506 Mounting Brackets 1-18
Rack-Mounting the CSS 11506 Chassis 1-19
Installing a CSS Module 1-19
Installation Precautions and Restrictions 1-20
Installation Precautions 1-20
Module Slot Restrictions 1-21
Unpacking a CSS Module 1-24
Installing a Module 1-24
Installing a Passive SCM in a CSS 11506 1-26
CHAPTER
2
Cabling the CSS 2-1
Cabling the CSS 11501 2-2
CSS 11501 Connectors and LEDs 2-4
Cabling the CSS 11503 and CSS 11506 Modules 2-7
CSS 11503 and CSS 11506 Module Overview 2-7
Switch Control Module Connectors and LEDs 2-11
Cisco 11500 Series Content Services Switch Hardware Installation Guide
vi
78-13884-03
Contents
Fast Ethernet Module Connectors and LEDs 2-14
Gigabit Ethernet Module Connectors and LEDs 2-16
Session Accelerator Module LEDs 2-18
Secure Socket Layer (SSL) Module LEDs 2-19
Connecting the Console 2-21
Connecting the Chassis to Ground 2-22
Tools and Supplies 2-22
Attaching the Grounding Cable 2-24
Connecting the Power Cord 2-26
Connecting a CSS 11501 Power Cord 2-26
Connecting a CSS 11503 Power Cord 2-27
Connecting a CSS 11503 AC Power Cord 2-27
Connecting a CSS 11503 DC Power Cord 2-28
Connecting a CSS 11506 Power Cord 2-31
Connecting a CSS 11506 AC Power Cord 2-31
Connecting a CSS 11506 DC Power Cord 2-33
Checking the DC Power Connection (CSS 11503 and CSS 11506) 2-36
CHAPTER
3
Booting and Configuring the CSS 3-1
Powering Up the CSS 3-1
Powering Down the CSS 3-2
Booting the CSS for the First Time 3-2
Hardware Initialization and Power-On Diagnostics 3-3
Entering Your License Key 3-5
Configuring the Ethernet Management Port 3-6
Changing the Default Username and Password 3-7
Password-Protecting the Offline Diagnostic Monitor Menu 3-8
Logging in to the CSS 3-9
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
vii
Contents
Using the Configuration Script 3-10
Configuring Layer 3 Load Balancing 3-12
Configuring Layer 5 Load Balancing 3-14
Configuring Proxy Cache 3-16
Configuring Transparent Cache 3-18
Where to Go Next 3-21
APPENDIX
A
Specifications A-1
Electrical Specifications A-2
Environmental Specifications A-3
Physical Specifications A-4
Module Specifications A-5
Disk Specifications A-5
Supported Standards A-6
Transport A-6
Network A-6
Routing A-7
Gateway A-7
Application A-7
Network Utilities A-7
Network Management A-8
APPENDIX
B
Cable Connector Pinouts B-1
RJ-45 Fast Ethernet Connector Pinouts B-2
RJ-45 RS-232 Console Port Pinouts B-3
Connecting the Console Port to a PC B-4
Connecting the Console Port to a Terminal B-5
Connecting the Console Port to a Modem B-6
RJ-45 Management Connector Pinouts B-7
Cisco 11500 Series Content Services Switch Hardware Installation Guide
viii
78-13884-03
Contents
APPENDIX
C
Troubleshooting C-1
Troubleshooting the Boot Process C-2
Diagnostic Tests for Hardware C-2
OffDM Verification of the Boot Configuration Record and Disk C-7
Errors in the Boot Configuration Record C-7
Failure of the Disk Drive in the SCM C-8
CSS 11501 Boot and Verification C-8
SCM Boot and Verification of the Modules C-9
Troubleshooting the Console Interface C-10
Troubleshooting the CSS Power Supply C-11
Troubleshooting the CSS 11501 Power Supply C-11
Troubleshooting the CSS 11503 Power Supply C-12
Troubleshooting the CSS 11506 Power Supply C-12
Troubleshooting the CSS Fans C-16
Troubleshooting the CSS 11501 Chassis Fans C-16
Troubleshooting the CSS 11503 Chassis Fans C-17
Troubleshooting the CSS 11506 Fan Module C-18
Troubleshooting the CSS 11501 C-19
Troubleshooting the CSS Modules C-21
Log File Information C-24
APPENDIX
D
Regulatory Compliance and Safety Information for the Cisco 11500 Series
Content Services Switch D-1
Agency Approvals D-2
FCC Class A Compliance Notice (United States) D-3
FCC Compliance Information Statement (United States) D-4
ICES-003 Class A Compliance Notice (Canada) D-5
Europe (EU) D-5
CISPR 22 Class A Warning D-5
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
ix
Contents
VCCI Class A Warning D-6
Class A Notice for Taiwan and Other Traditional Chinese Markets D-8
Class A EMC Warning D-8
Safety Requirements D-9
Laser Safety D-10
Translated Safety Warnings D-11
Warning Definition D-11
Lithium Battery Disposal Warning D-13
Radiation from Open Port Aperture Warning D-14
Class 1 Laser Product Warning D-16
Qualified Personnel Warning D-16
Two-Person Lifting Warning D-17
Lightning Activity Warning D-19
Jewelry Removal Warning D-20
Reading Instructions Warning D-21
Disconnect Device Warning D-22
Chassis Installation Warning D-23
Ground Conductor Warning D-25
Installation and Replacement Warning D-26
Use Copper Conductors Only D-27
Short-Circuit Protection Warning D-28
Wire Preparation Warning D-29
DC Power Source Warning D-31
Dual Power Supply Warning D-33
DC Power Supply Wiring Warning D-34
Blank Faceplate Requirement Warning D-36
Power Off Before Working on System Warning D-38
Cisco 11500 Series Content Services Switch Hardware Installation Guide
x
78-13884-03
Contents
Fan Injury Warning D-39
AC and DC Power Module Warning D-40
Power Cord Warning (other versions available) D-41
Ground Conductor Warning D-42
INDEX
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xi
Contents
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xii
78-13884-03
F I G U R E S
Figure 1-1
Front-Mounting the Mounting Brackets on the CSS 11501
1-13
Figure 1-2
Front-Mounting the Mounting Brackets on the CSS 11503
1-15
Figure 1-3
Mid-Mounting the Mounting Brackets on the CSS 11503
Figure 1-4
Front-Mounting Position of the CSS 11506 Mounting Brackets
Figure 1-5
Mid-Mounting the Mounting Brackets on the CSS 11506
Figure 1-6
Fully-Configured CSS 11503
1-22
Figure 1-7
Fully-Configured CSS 11506
1-23
Figure 1-8
Installing a Module into a CSS Chassis
Figure 1-9
Installing a PCMCIA Cover on an SCM
Figure 2-1
CSS 11501 Connectors and LEDs
Figure 2-2
CSS 11503 Content Services Switch
2-9
Figure 2-3
CSS 11506 Content Services Switch
2-10
Figure 2-4
Switch Control Module Connectors and LEDs
Figure 2-5
8-Port Fast Ethernet Module Connectors and LEDs
Figure 2-6
16-Port Fast Ethernet Module Connectors and LEDs
Figure 2-7
Gigabit Ethernet Module Connectors and LEDs
Figure 2-8
Session Accelerator Module LEDs
Figure 2-9
SSL Module LEDs
Figure 2-10
Attaching Grounding Wire to Grounding Lug
Figure 2-11
Connecting a CSS 11501 AC Power Cord
2-26
Figure 2-12
Connecting a CSS 11503 AC Power Cord
2-27
Figure 2-13
Location of the CSS 11503 DC Power Supply Connectors
Figure 2-14
Connecting a CSS 11506 AC Power Cord
1-16
1-17
1-18
1-25
1-27
2-4
2-12
2-14
2-15
2-17
2-18
2-20
2-25
2-29
2-32
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xiii
Figures
Figure 2-15
Location of CSS 11506 DC Power Supply Connectors
Figure C-1
Location of the CSS 11506 Power Supplies
Figure C-2
CSS 11506 AC Power Supply LEDs
C-14
Figure C-3
CSS 11506 DC Power Supply LEDs
C-14
2-34
C-13
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xiv
78-13884-03
T A B L E S
Table 1-1
AC Electrical Specifications
1-6
Table 1-2
DC Electrical Specifications
1-6
Table 1-3
CSS 11503 Chassis Slot Restriction
1-21
Table 1-4
CSS 11506 Chassis Slot Restriction
1-21
Table 2-1
CSS 11501 LED Descriptions
Table 2-2
Switch Control Module LED Descriptions
Table 2-3
Fast Ethernet Module LED Descriptions
Table 2-4
Gigabit Ethernet Module LED Descriptions
Table 2-5
Session Accelerator Module LED Descriptions
Table 2-6
SSL Module LED Descriptions
Table 2-7
CSS Console Port Default Settings
Table 2-8
Tools and Supplies
Table 2-9
CSS 11503 to DC Power Source Cabling
2-30
Table 2-10
CSS 11506 to DC Power Source Cabling
2-35
Table 3-1
Status LEDs Boot Definitions
Table A-1
AC Electrical Specifications
A-2
Table A-2
DC Electrical Specifications
A-2
Table A-3
Environmental Specifications
Table A-4
Physical Specifications
A-4
Table A-5
Module Specifications
A-5
Table A-6
Disk Specifications
Table B-1
RJ-45 Fast Ethernet Connector Pinouts
Table B-2
RJ-45 RS-232 Serial Connector Pinouts for the Console Port
2-5
2-13
2-16
2-17
2-19
2-20
2-21
2-22
3-4
A-3
A-5
B-2
B-3
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xv
Tables
Table B-3
Console Port to PC Signals and Pinouts
Table B-4
Console Port to Terminal Signals and Pinouts
Table B-5
Console Port to Modem Signals and Pinouts
Table B-6
RJ-45 Management Connector Pinouts
Table C-1
Fields in the Diagnostic Monitor Error Message
Table C-2
Troubleshooting the Console Interface
Table C-3
LEDs of the CSS 11506 Power Supply
Table C-4
Troubleshooting the CSS 11501
Table C-5
Troubleshooting the CSS Modules
Table C-6
CSS Log File Descriptions
Table D-1
Regulatory Approval Requirements
B-4
B-5
B-6
B-7
C-4
C-10
C-15
C-19
C-22
C-24
D-2
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xvi
78-13884-03
About This Guide
This guide is intended to help you install your Cisco 11500 series content services
switch (hereinafter referred to as the CSS) and get it into operation. It provides
you with instructions for installing, cabling, booting, and configuring the CSS
using the configuration script.
Audience
Warning
Only trained and qualified personnel are allowed to install or replace this
equipment.
This guide is intended for the following trained and qualified service personnel
who are responsible for installing and operating the CSS:
•
System installer
•
Hardware technician
•
System operator
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xvii
About This Guide
How to Use This Guide
How to Use This Guide
This section describes the chapters and contents in this guide.
Chapter/Appendix
Description
Chapter 1,
Unpacking and
Installing the CSS
This chapter provides instructions for unpacking and
installing the CSS.
Chapter 2,
Cabling the CSS
This chapter describes the CSS 11501 integrated
platform and the CSS 11503 and 11506 modular
platforms, including LEDs and connectors. This chapter
also provides instructions for connecting the console and
power cords.
This chapter provides information on powering and
Chapter 3,
Booting and
booting the CSS for the first time. This chapter also
Configuring the CSS describes how to configure the CSS using the
configuration script.
Appendix A,
Specifications
This appendix provides specifications for the CSS and its
components.
Appendix B,
Cable Connector
Pinouts
This appendix provides pinouts for each connector on the
CSS.
Appendix C,
Troubleshooting
This appendix provides troubleshooting information for
the CSS, power supply, and the boot process.
Appendix D,
Regulatory
Compliance and
Safety Information
for the Cisco 11500
Series Content
Services Switch
This appendix provides information on regulatory
compliance and safety pertaining to the CSS.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xviii
78-13884-03
About This Guide
Related Documentation
Related Documentation
In addition to this document, the content services switch documentation set
includes the following publications:
Document Title
Description
Release Note for the Cisco This release note provides information on
11500 Series Content
operating considerations, caveats, and CLI
Services Switch
commands for the Cisco 11500 series CSS.
Cisco Content Services
Switch Administration
Guide
This guide describes how to perform
administration tasks on the CSS including logging
into the CSS, upgrading your CSS software, and
configuring the following:
•
Management ports, interfaces, and circuits
•
DNS, ARP, RIP, IP, and bridging features
•
OSPF
•
Logging, including displaying log messages
and interpreting sys.log messages
•
User profile and CSS parameters
•
SNMP
•
RMON
•
Offline Diagnostic Monitor (Offline DM)
menu
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xix
About This Guide
Related Documentation
Document Title
Description
Cisco Content Services
Switch Basic
Configuration Guide
This guide describes how to perform basic CSS
configuration tasks, including:
Cisco Content Services
Switch Advanced
Configuration Guide
•
Services
•
Owners
•
Content rules
•
Sticky parameters
•
HTTP header load balancing
•
Source groups, Access Control Lists (ACLs),
Extension Qualifier Lists (EQLs), Uniform
Resource Locator Qualifier Lists (URQLs),
Network Qualifier Lists (NQLs), and Domain
Qualifier Lists (DQLs)
•
Caching
This guide describes how to perform advanced CSS
configuration tasks, including:
•
Domain Name Service (DNS)
•
DNS Sticky
•
Content Routing Agent
•
Client Side Accelerator
•
Network proximity
•
VIP and virtual IP interface redundancy
•
Box-to-box redundancy
•
Demand-based content replication and content
staging and replication
•
Secure Socket Layer (SSL) termination with
the SSL Acceleration Module
•
Firewall load balancing
•
CSS scripting language
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xx
78-13884-03
About This Guide
Symbols and Conventions
Document Title
Description
Cisco Content Services
Switch Command
Reference
This guide provides an alphabetical list of all CSS
Command Line Interface commands including
syntax, options, and related commands.
Cisco Content Services
This guide provides an overview on using the
Switch Device
Device Management user interface, an
Management User’s Guide HTML-based Web application that you use to
configure and manage a CSS.
Symbols and Conventions
This guide uses the following symbols and conventions to emphasize certain
information.
Caution
Note
A caution means that a specific action you take could cause a loss of data or
adversely impact use of the equipment.
A note provides important related information, reminders, and recommendations.
Bold text indicates a command in a paragraph.
Courier text
indicates text that appears in a command line, including the CLI
prompt.
Courier bold text
indicates commands and text you enter in a command line.
Italics text indicates the first occurrence of a new term, book title, and emphasized
text.
1.
A numbered list indicates that the order of the list items is important.
a. An alphabetical list indicates that the order of the secondary list items is
important.
•
A bulleted list indicates that the order of the list topics is unimportant.
– An indented list indicates that the order of the list subtopics is
unimportant.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xxi
About This Guide
Symbols and Conventions
Before you install, configure, or perform maintenance on the CSS, review the
documentation for the procedure you are about to perform, paying special
attention to the safety warnings. If you need translations of the safety warnings,
refer to the Appendix D, Regulatory Compliance and Safety Information for the
Cisco 11500 Series Content Services Switch.
Warning
This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents. (To see translations of the warnings that appear in this
publication, refer to the appendix “Translated Safety Warnings” in the
installation guide that accompanied this device.)
Waarschuwing
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat
werken, dient u zich bewust te zijn van de bij elektrische schakelingen
betrokken risico’s en dient u op de hoogte te zijn van standaard maatregelen
om ongelukken te voorkomen. (Voor vertalingen van de waarschuwingen die
in deze publicatie verschijnen, kunt u het aanhangsel “Translated Safety
Warnings” (Vertalingen van veiligheidsvoorschriften) in de installatiegids die
bij dit toestel is ingesloten, raadplegen.
Varoitus
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa
ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota
selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista
onnettomuuksien ehkäisykeinoista. (Tässä julkaisussa esiintyvien
varoitusten käännökset löydät tämän laitteen mukana olevan asennusoppaan
liitteestä "Translated Safety Warnings" (käännetyt turvallisuutta koskevat
varoitukset).)
Attention
Ce symbole d’avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures. Avant d’accéder à cet équipement,
soyez conscient des dangers posés par les circuits électriques et
familiarisez-vous avec les procédures courantes de prévention des
accidents. Pour obtenir les traductions des mises en garde figurant dans cette
publication, veuillez consulter l’annexe intitulée « Translated Safety
Warnings » (Traduction des avis de sécurité) dans le guide d’installation qui
accompagne cet appareil.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xxii
78-13884-03
About This Guide
Symbols and Conventions
Warnung
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die
zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an
irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen
Stromkreisen verbundenen Gefahren und der Standardpraktiken zur
Vermeidung von Unfällen bewußt. (Übersetzungen der in dieser
Veröffentlichung enthaltenen Warnhinweise finden Sie im Anhang mit dem
Titel “Translated Safety Warnings” (Übersetzung der Warnhinweise) in der
diesem Gerät beiliegenden Installationsanleitung.)
Avvertenza
Questo simbolo di avvertenza indica un pericolo. Si è in una situazione che
può causare infortuni. Prima di lavorare su qualsiasi apparecchiatura,
occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente
delle pratiche standard per la prevenzione di incidenti. La traduzione delle
avvertenze riportate in questa pubblicazione si trova nell’appendice,
“Translated Safety Warnings” (Traduzione delle avvertenze di sicurezza), del
manuale d’installazione che accompagna questo dispositivo.
Advarsel
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre
til personskade. Før du utfører arbeid på utstyr, må du være oppmerksom på de
faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med
vanlig praksis når det gjelder å unngå ulykker. (Hvis du vil se oversettelser av
de advarslene som finnes i denne publikasjonen, kan du se i vedlegget
"Translated Safety Warnings" [Oversatte sikkerhetsadvarsler] i
installasjonsveiledningen som ble levert med denne enheten.)
Aviso
Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe
poderá causar danos fisicos. Antes de começar a trabalhar com qualquer
equipamento, familiarize-se com os perigos relacionados com circuitos
eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis
acidentes. (Para ver as traduções dos avisos que constam desta publicação,
consulte o apêndice “Translated Safety Warnings” - “Traduções dos Avisos
de Segurança”, no guia de instalação que acompanha este dispositivo).
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xxiii
About This Guide
Obtaining Documentation
¡Advertencia!
Varning!
Este símbolo de aviso significa peligro. Existe riesgo para su integridad
física. Antes de manipular cualquier equipo, considerar los riesgos que
entraña la corriente eléctrica y familiarizarse con los procedimientos
estándar de prevención de accidentes. (Para ver traducciones de las
advertencias que aparecen en esta publicación, consultar el apéndice
titulado “Translated Safety Warnings,” en la guía de instalación que se
acompaña con este dispositivo.)
Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan
leda till personskada. Innan du utför arbete på någon utrustning måste du vara
medveten om farorna med elkretsar och känna till vanligt förfarande för att
förebygga skador. (Se förklaringar av de varningar som förekommer i denna
publikation i appendix "Translated Safety Warnings" [Översatta
säkerhetsvarningar] i den installationshandbok som medföljer denna
anordning.)
Obtaining Documentation
These sections explain how to obtain documentation from Cisco Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at
this URL:
http://www.cisco.com
Translated documentation is available at this URL:
http://www.cisco.com/public/countries_languages.shtml
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xxiv
78-13884-03
About This Guide
Obtaining Documentation
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco
Documentation CD-ROM package, which is shipped with your product. The
Documentation CD-ROM is updated monthly and may be more current than
printed documentation. The CD-ROM package is available as a single unit or
through an annual subscription.
Ordering Documentation
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product
documentation from the Networking Products MarketPlace:
http://www.cisco.com/cgi-bin/order/order_root.pl
•
Registered Cisco.com users can order the Documentation CD-ROM through
the online Subscription Store:
http://www.cisco.com/go/subscription
•
Nonregistered Cisco.com users can order documentation through a local
account representative by calling Cisco Systems Corporate Headquarters
(California, U.S.A.) at 408 526-7208 or, elsewhere in North America, by
calling 800 553-NETS (6387).
Documentation Feedback
You can submit comments electronically on Cisco.com. In the Cisco
Documentation home page, click the Fax or Email option in the “Leave
Feedback” section at the bottom of the page.
You can e-mail your comments to bug-doc@cisco.com.
You can submit your comments by mail by using the response card behind the
front cover of your document or by writing to the following address:
Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xxv
About This Guide
Obtaining Technical Assistance
Obtaining Technical Assistance
Cisco provides Cisco.com as a starting point for all technical assistance.
Customers and partners can obtain online documentation, troubleshooting tips,
and sample configurations from online tools by using the Cisco Technical
Assistance Center (TAC) Web Site. Cisco.com registered users have complete
access to the technical support resources on the Cisco TAC Web Site.
Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that
provides immediate, open access to Cisco information, networking solutions,
services, programs, and resources at any time, from anywhere in the world.
Cisco.com is a highly integrated Internet application and a powerful, easy-to-use
tool that provides a broad range of features and services to help you with these
tasks:
•
Streamline business processes and improve productivity
•
Resolve technical issues with online support
•
Download and test software packages
•
Order Cisco learning materials and merchandise
•
Register for online skill assessment, training, and certification programs
If you want to obtain customized information and service, you can self-register on
Cisco.com. To access Cisco.com, go to this URL:
http://www.cisco.com
Technical Assistance Center
The Cisco Technical Assistance Center (TAC) is available to all customers who
need technical assistance with a Cisco product, technology, or solution. Two
levels of support are available: the Cisco TAC Web Site and the Cisco TAC
Escalation Center.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xxvi
78-13884-03
About This Guide
Obtaining Technical Assistance
Cisco TAC inquiries are categorized according to the urgency of the issue:
•
Priority level 4 (P4) — You need information or assistance concerning Cisco
product capabilities, product installation, or basic product configuration.
•
Priority level 3 (P3) — Your network performance is degraded. Network
functionality is noticeably impaired, but most business operations continue.
•
Priority level 2 (P2) — Your production network is severely degraded,
affecting significant aspects of business operations. No workaround is
available.
•
Priority level 1 (P1) — Your production network is down, and a critical
impact to business operations will occur if service is not restored quickly. No
workaround is available.
The Cisco TAC resource that you choose is based on the priority of the problem
and the conditions of service contracts, when applicable.
Cisco TAC Web Site
You can use the Cisco TAC Web Site to resolve P3 and P4 issues yourself, saving
both cost and time. The site provides around-the-clock access to online tools,
knowledge bases, and software. To access the Cisco TAC Web Site, go to this
URL:
http://www.cisco.com/tac
All customers, partners, and resellers who have a valid Cisco service contract have
complete access to the technical support resources on the Cisco TAC Web Site.
The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have
a valid service contract but do not have a login ID or password, go to this URL to
register:
http://www.cisco.com/register/
If you are a Cisco.com registered user, and you cannot resolve your technical
issues by using the Cisco TAC Web Site, you can open a case online by using the
TAC Case Open tool at this URL:
http://www.cisco.com/tac/caseopen
If you have Internet access, we recommend that you open P3 and P4 cases through
the Cisco TAC Web Site.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
xxvii
About This Guide
Obtaining Technical Assistance
Cisco TAC Escalation Center
The Cisco TAC Escalation Center addresses priority level 1 or priority level 2
issues. These classifications are assigned when severe network degradation
significantly impacts business operations. When you contact the TAC Escalation
Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.
To obtain a directory of toll-free Cisco TAC telephone numbers for your country,
go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Before calling, please check with your network operations center to determine the
level of Cisco support services to which your company is entitled: for example,
SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). When
you call the center, please have available your service agreement number and your
product serial number.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
xxviii
78-13884-03
C H A P T E R
1
Unpacking and Installing the CSS
Warning
This is a class A product. In a domestic environment this product may cause
radio interference, in which case the user may be required to take adequate
measures.
This chapter describes how to unpack and install the CSS as a free-standing or
rack-mounted unit.
This chapter contains the following sections:
•
Site Requirements
•
Safety Guidelines
•
Required Tools and Equipment
•
Shipment Contents
•
Unpacking the CSS
•
If the Product is Damaged
•
Preinstallation Requirements
•
Installing the CSS 11501
•
Installing the CSS 11503
•
Installing the CSS 11506
•
Installing a CSS Module
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-1
Chapter 1
Unpacking and Installing the CSS
Site Requirements
Note
For information on installing a replacement component in the CSS (such as a
replacement PCMCIA disk or a power supply), refer to the reference sheet
included with the component.
Site Requirements
Before you select an installation site for the CSS, read the electrical,
environmental, and physical requirements as described in Appendix A,
Specifications.
Safety Guidelines
When you install the CSS, observe all of the caution and warning statements in
the installation procedures. For warning translations, refer to Appendix D,
Regulatory Compliance and Safety Information for the Cisco 11500 Series
Content Services Switch.
Read the following guidelines to help ensure your safety and protect the
equipment. These guidelines may not cover all potentially hazardous situations
you may encounter during system installation, so be alert.
•
The installation of your CSS must comply with national and local electrical
codes. In the United States, this means the National Fire Protection
Association (NFPA) 70, United States National Electrical Code. In Canada,
Canadian Electrical Code, part I, CC22.1. In other countries, International
Electrotechnical Commission (IEC) 364, part 1 through part 7.
•
Keep tools and chassis components away from walk areas.
•
Do not wear loose clothing, jewelry (including rings and chains), or other
items that could get caught in the chassis.
•
The AC-powered CSS ships with a three-wire AC electrical grounding-type
plug, which only fits into a grounding-type power outlet. This is a safety
feature. Ensure the equipment grounding is in compliance with local and
national electrical codes.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-2
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Safety Guidelines
Warning
•
The DC-powered CSS 11503 and CSS 11506 are not shipped with the wiring
required to connect to the DC source. You must provide input, return, and
earth (grounding) wiring at the site (refer to Chapter 2, Cabling the CSS), and
install and protect the wiring in accordance with local and national wiring
regulations.
•
The CSS operates safely when it is used in accordance with its marked
electrical ratings and product usage instructions.
Only trained and qualified personnel should be allowed to install or replace this
equipment.
Chassis-Lifting Guidelines for the CSS 11503 and CSS 11506
The fully-configured CSS 11503 weighs approximately 34 pounds. The
fully-configured CSS 11506 weighs approximately 58 pounds. The chassis is not
intended to be moved frequently. Before you install the CSS, ensure that your site
is properly prepared; by doing so, you can avoid moving the chassis later to
accommodate power sources and network connections.
When lifting either the CSS 11503 or CSS 11506 chassis, follow these guidelines:
•
Two or more people are required to lift the CSS 11506 chassis (as described
in the procedure at the end of this section). Never attempt to lift the chassis
by yourself. Because of the size and weight of the chassis, use at least two
people to safely lift and move it; by doing so, you can avoid causing injury or
damaging the equipment.
•
When lifting a chassis, ensure that your footing is solid, and balance the
weight of the chassis between your feet.
•
Lift the chassis slowly; never move suddenly or twist your body as you lift.
•
Keep your back straight and lift the chassis with your legs, not your back. If
you must bend down to lift the chassis, bend at the knees, not at the waist, to
reduce the strain on your back muscles.
•
If you remove the fan assembly and power modules to lighten the chassis, be
sure to provide anti-static mats or bags to protect the removed components.
Be careful when you remove the power modules—they are heavy.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-3
Chapter 1
Unpacking and Installing the CSS
Safety Guidelines
Warning
•
Cisco Systems recommends that you leave line cards installed in the chassis.
Removing line cards greatly increases the chances of damage to the chassis
or components, and introduces the possibility that you will unintentionally
change the configuration.
•
Always disconnect all external cables before lifting or moving the chassis.
Two people are required to lift the CSS 11506 chassis. To prevent injury, keep
your back straight and lift with your legs, not your back.
To safely lift the CSS 11506 chassis, perform the following steps:
1.
Stand on one side of the chassis and tell your helper to stand on the other side.
2.
Place one hand under the front or side of the chassis, and tell your helper to
do the same.
3.
With the other hand, grasp the top-rear of the chassis and carefully lift the
chassis.
Electrical Safety
Follow these basic guidelines when you are working with any electrical
equipment:
•
Before you begin any procedures requiring access to the chassis interior,
locate the emergency power-off switch for the room in which you are
working.
•
Disconnect all power and external cables before installing or removing a
chassis.
•
Do not work alone when potentially hazardous conditions exist.
•
Never assume that power has been disconnected from a circuit; always check.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-4
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Safety Guidelines
•
Do not perform any action that creates a potential hazard to people or makes
the equipment unsafe. Never install equipment that appears damaged.
•
Carefully examine your work area for possible hazards such as moist floors,
ungrounded power extension cables, and missing safety grounds.
Use the following guidelines when you work with any equipment that is
connected to telephone wiring or other network cabling, even if that equipment is
disconnected from its power source.
•
Never install telephone wiring during a lightning storm.
•
Never install a telephone jack in a wet location unless the jack is specifically
designed for wet locations.
•
Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
•
Use caution when installing or modifying telephone lines.
Warning
Do not work on the system or connect or disconnect cables during periods of
lightning activity.
Warning
Before you work on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when
connected to power and ground and the heat can cause serious burns or weld
the metal object to the terminals.
Warning
Read the installation instructions before you connect the system to its power
source.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-5
Chapter 1
Unpacking and Installing the CSS
Safety Guidelines
Specifications for Cisco 11500 Series Power Supplies
Table 1-1 describes the CSS 11501, CSS 11503, and CSS 11506 AC electrical
specifications.
Table 1-1
AC Electrical Specifications
AC Specification
CSS 11501
CSS 11503
CSS 11506
Input Voltage AC
100 to 240 VAC
50 to 60 Hz
100 to 240 VAC
50 to 60 Hz
100 to 240 VAC
50 to 60 Hz
Current AC (max@
100 VAC)
1.6 Amps
5 Amps
9 Amps
Power Consumption
(maximum)
150VA
430VA
860VA
Heat Dissipation
512 BTU/hr
1468 BTU/hr
2939 BTU/hr
Table 1-2 describes the CSS 11503 and CSS 11506 DC electrical specifications.
Table 1-2
DC Electrical Specifications
DC Specification
CSS 11503
CSS 11506
Voltage DC
-48.0 to -60.0 VDC
-48.0 to -60.0 VDC
Current DC (maximum)
9 Amps
18 Amps
Power Consumption
(maximum)
430VA
860VA
Heat Dissipation
1468 BTU/hr
2939 BTU/hr
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-6
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Required Tools and Equipment
Power Guidelines for DC Systems (CSS 11503 and CSS 11506)
The DC-input power supply allows the CSS 11503 and CSS 11506 to operate at
–48 VDC nominal in North America and at –48 VDC or –60 VDC in Europe.
See Table 1-2 for system power specifications, including input voltage and
operating frequency ranges.
Warning
Incorporate a readily accessible 2-poled disconnect device into the fixed
wiring.
Follow your local and national electrical codes for DC wiring.
Required Tools and Equipment
To install the CSS hardware, you need the following tools and equipment:
•
A #1 Phillips-head screwdriver
•
An anti-static wrist strap, provided in the CSS accessory kit
•
A hand lift (recommended) for lifting the CSS chassis into the equipment
rack
Once you complete the installation, you need a console terminal (or equivalent)
that runs at 9600 baud to enter console commands (refer to Chapter 2, Cabling the
CSS).
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-7
Chapter 1
Unpacking and Installing the CSS
Shipment Contents
Shipment Contents
The CSS shipment contains the following items, except where noted:
•
Content Services Switch
•
Anti-static wrist strap
•
Four rubber feet (CSS 11501 and CSS 11503 only)
•
Mounting brackets and hardware (installed on the CSS 11506)
•
RJ-45 to female 25-pin sub-d connector
•
RJ-45 to female 9-pin sub-d connector
•
RJ-45 console cable
•
Software License Key
Note
•
Your license key is located on a white label printed with the “S11K-”
product code and is found inside the CSS accessory kit. If you cannot
find the software license key, call the Cisco Technical Assistance
Center (TAC) toll free, 24 hours a day, 7 days a week at
1-800-553-2447 or 1-408-526-7209. You can also send email to TAC
at tac@cisco.com.
Content Services Switch Documentation:
– Documentation Guide
– Hardware Installation Guide
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-8
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Unpacking the CSS
Unpacking the CSS
The CSS is shipped in a protective shipping carton. The CSS 11501 is shipped as
a self-contained chassis; no components can be added or removed.The CSS 11503
and CSS 11506 contains the power supply, fan unit, Switch Module (SM), Switch
Control Module (SCM), and all ordered I/O modules (IOMs) preinstalled.
This section describes:
•
Unpacking the CSS 11501
•
Unpacking the CSS 11503 or CSS 11506
•
If the Product is Damaged
Unpacking the CSS 11501
To unpack the CSS 11501:
1.
Remove the CSS 11501 accessories from the shipping carton. Save the
packing materials in case you need to repack the CSS later.
2.
Check the configuration of the CSS 11501 and the accessories against the
items listed on the packing slip. Report any discrepancies as described in “If
the Product is Damaged” section.
3.
To install the CSS 11501, go to “Preinstallation Requirements”.
Unpacking the CSS 11503 or CSS 11506
Due to the size and weight of a CSS 11503 or CSS 11506, move it to the
installation site before unpacking it from the shipping carton.
To unpack the CSS 11503 or CSS 11506:
1.
Remove the CSS accessories from the shipping carton. Save the packing
materials in case you need to repack the CSS later.
2.
Check the configuration of the CSS and the accessories against the items
listed on the packing slip. Report any discrepancies as described in “If the
Product is Damaged” section.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-9
Chapter 1
Unpacking and Installing the CSS
Unpacking the CSS
3.
Warning
Carefully remove the CSS from the carton.
Two people are required to lift the CSS 11506 chassis. Grasp the chassis
underneath the lower edge and lift with both hands. To prevent injury, keep your
back straight and lift with your legs, not your back. To prevent damage to the
chassis and components, never attempt to lift the chassis with the handles on
the power supplies, fan module, or on the interface processors, or by the plastic
panels on the front of the chassis. These handles were not designed to support
the weight of the chassis.
4.
To install the CSS 11503 or CSS 11506, go to “Preinstallation
Requirements”.
If the Product is Damaged
If any portion of the unit or component is damaged in transit, forward an
immediate request to the delivering carrier to perform an inspection of the product
and to prepare a damage report. Save the container and all packing materials until
the contents are verified.
Concurrently, report the nature and extent of the damage to Customer Service.
Report the problem or deficiency to Customer Service along with the model
number and serial number. Upon receipt of this information, you will be provided
with service instructions, or a Return Material Authorization (RMA) number and
shipping information. To obtain assistance, refer to “About This Guide”, the
“Obtaining Documentation” section.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-10
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Preinstallation Requirements
Preinstallation Requirements
Prior to installing the CSS, observe the following installation requirements:
•
The ambient operating temperature is 32° to 104°F (0 to 40°C).
If you install the CSS in a closed or multi-unit rack, the ambient operating
temperature of the rack environment may be greater than the room ambient
temperature. Ensure that the temperature does not exceed the CSS maximum
ambient operating temperature.
Caution
•
The minimum clearance requirement is 4 inches (10 cm) of air flow space on
both sides of the chassis.
•
Ensure that the CSS is reliably grounded to earth. Cisco Systems recommends
that you do not use power strips or extension cords to connect the CSS to the
power source.
To prevent the chassis from overheating, never install a CSS in an enclosed rack
or in a room that is not properly ventilated or air conditioned.
See the following sections for the steps to install a CSS:
•
Installing the CSS 11501
•
Installing the CSS 11503
•
Installing the CSS 11506
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-11
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11501
Installing the CSS 11501
The CSS 11501 can be a freestanding unit or installed in a 19-inch equipment
rack, as described in the following sections.
Warning
Note
Do not remove the CSS 11501 cover. There are electrical shock hazards present
in the unit if the cover is removed. The fans and power supply in a CSS 11501 are
not user-serviceable or installable components.
Removing the CSS 11501 cover voids its warranty.
This section covers:
•
Installing a CSS 11501 as a Freestanding Unit
•
Installing a CSS 11501 as a Rackmounted Unit
Installing a CSS 11501 as a Freestanding Unit
To install a freestanding CSS 11501:
Note
1.
Position the CSS 11501 on the selected flat surface.
2.
Attach the rubber feet, provided in the accessory kit, to each bottom corner
of the CSS.
All cables connect to the front of the chassis with the exception of the power cord.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-12
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11501
Installing a CSS 11501 as a Rackmounted Unit
Before you begin, you need the mounting brackets and the 12 Phillips screws
shipped in the accessory kit accompanying the CSS 11501, and a #2 Phillips
screwdriver.
To install the mounting brackets on the CSS 11501 chassis:
1.
Position the CSS with its front panel facing you. On the left and right sides
of its chassis, note the screw holes for installing the mounting brackets.
2.
Position a mounting bracket on one side of the chassis. Align it with the
appropriate screw holes for front- or mid-mounting.
Figure 1-2 illustrates front-mounting the mounting brackets.
Figure 1-1
Front-Mounting the Mounting Brackets on the CSS 11501
STATUS
LINK/ACT
DUPLEX
LINK DPLX
CONSOLE
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
PCMCIA
2
3
10/100
CISCO 115
LINK DPLX
CONTE
GE
4
5
6
7
10/100
LINK
00 SERIES
NT SE
RV I C
ES SW
ITC
H
8
78675
1
3.
Secure the mounting bracket to the CSS with six screws provided.
4.
Repeat steps 2 and 3 to install a mounting bracket on the other side of the
CSS.
You are ready to install the CSS in the rack.To install the CSS 11501 into an
equipment rack:
1.
Raise the CSS to the installation height and align the screw holes on the
mounting bracket with the holes on the equipment rack.
2.
Secure each mounting bracket to each side of the rack.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-13
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11503
Installing the CSS 11503
The CSS 11503 can be a freestanding unit or installed in a 19-inch equipment
rack, as described in the following sections.
Warning
Note
Do not remove the CSS 11503 cover. There are electrical shock hazards present
in the unit if the cover is removed. The fans and power supply in a CSS 11503 are
not user-serviceable or installable components.
Removing the CSS 11503 cover voids its warranty.
This section covers:
•
Installing a CSS 11503 as a Freestanding Unit
•
Installing a CSS 11503 as a Rackmounted Unit
Installing a CSS 11503 as a Freestanding Unit
To install a freestanding CSS 11503:
Note
1.
Position the CSS 11503 on the selected flat surface.
2.
Attach the rubber feet, provided in the accessory kit, to each bottom corner
of the CSS.
All cables connect to the front of the unit with the exception of the power cord.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-14
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11503
Installing a CSS 11503 as a Rackmounted Unit
Before you rack-mount the CSS 11503:
•
Determine if you want to front-mount or mid-mount the mounting brackets
on the CSS chassis. Refer to the location of the mounting bars in the
equipment cabinet to determine the mount position of the mounting brackets.
•
Install the mounting brackets on the CSS, as described below.
Before you begin, you need the mounting brackets and the eight Phillips screws
shipped in the accessory kit accompanying the CSS 11503, and a #1 Phillips
screwdriver.
To install the mounting brackets on the CSS chassis:
1.
Position the CSS with its front panel facing you. On the left and right sides
of its chassis, note the screw holes for installing the mounting brackets.
2.
Position a mounting bracket on one side of the chassis. Align it with the
appropriate screw holes for front- or mid-mounting.
Figure 1-2 illustrates front-mounting the mounting brackets. Figure 1-3
illustrates mid-mounting of the brackets.
Front-Mounting the Mounting Brackets on the CSS 11503
59538
Figure 1-2
MANAGEMENT
10BASE-T
DUPLEX
LINK
CISCO 115
2
3
4
CONTE
5
6
7
8
9 10
11 12
13 14
15
1
CONSOLE
LINK
LINK
DPLX
DPLX
2
3
4
5
6
7
8
NT
00 SERIES
SERVIC
ES
SWITC
H
9 10
11 12
13 14
15
LINK
LINK
DPLX
DPLX
16 Fast Ethernet
1
LINK
GE 2
SLOT 0
System Control
3
SLOT 1
CSS5-10M-16FE
2
CSS5-SCM-2GE
GE 1
1
PCMCIA
CSS5-10M-16FE
LINK/ACT
16 Fast Ethernet
STATUS
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-15
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11503
Mid-Mounting the Mounting Brackets on the CSS 11503
59539
Figure 1-3
MANAGEMENT
10BASE-T
DUPLEX
LINK
CISCO 115
2
3
4
CONTE
5
6
7
8
9 10
11 12
13 14
15
SLOT 0
1
CONSOLE
LINK
LINK
DPLX
DPLX
2
3
4
5
6
7
8
NT
00 SERIES
SERVIC
ES
SWITC
H
9 10
11 12
13 14
15
LINK
LINK
DPLX
DPLX
16 Fast Ethernet
GE 2
SLOT 1
System Control
3
1
LINK
PCMCIA
CSS5-10M-16FE
2
CSS5-SCM-2GE
GE 1
1
CSS5-10M-16FE
LINK/ACT
16 Fast Ethernet
STATUS
3.
Secure the mounting bracket to the CSS with four screws provided.
4.
Repeat steps 2 and 3 to install a mounting bracket on the other side of the
CSS.
You are ready to install the CSS in the rack. Before you install the CSS 11503 into
an equipment rack, note the following:
Warning
•
Always install heavier equipment in the lower half of a rack to maintain a low
center of gravity. This practice helps prevent the rack from falling over.
•
Install rack stabilizers (if available) before you mount the chassis.
At least three people are required to mount the chassis in the equipment rack:
two people are needed to hold the chassis in place while a third person
tightens the mounting screws.
To install the CSS 11503 into an equipment rack:
1.
Raise the CSS to the installation height and align the screw holes on the
mounting bracket with the holes on the equipment rack.
2.
Secure each mounting bracket to each side of the rack.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-16
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11506
Installing the CSS 11506
The CSS 11506 must be installed in a 19-inch equipment rack. When positioning
the CSS 11506 for installation, keep in mind that all cables connect to the front of
the unit.
Before you rack-mount the CSS 11506 chassis, determine whether to front-mount
or mid-mount the CSS chassis in the rack. The mounting brackets are preinstalled
in the front-mounted position on the chassis, as shown in Figure 1-4. They are
ready for installation in the equipment cabinet, as described in “Rack-Mounting
the CSS 11506 Chassis”. To mid-mount the mounting brackets to the chassis,
proceed to “Mid-Mounting the CSS 11506 Mounting Brackets”.
Figure 1-4
Front-Mounting Position of the CSS 11506 Mounting Brackets
CSS506-SM
CSS506-SM
MANAGEMENT
10BASE-T
CISCO 115
DUPLEX
1
LINK
GE 2
LINK
CONTE
2
3
4
5
6
7
8
PCMCIA
LINK
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
5
6
7
8
DPLX
DPLX
5
6
PS1
PS2
PS3
7
6
7
8
00 SERIES
SERVIC
ES
SWITC
H
DPLX
DPLX
9 10
11 12
13 14
15
3
4
5
8
DPLX
DPLX
9 10
11 12
13 14
15
LINK
LINK
DPLX
DPLX
AC DC
OK OK
AC DC
OK OK
59540
4
6
CSS5-10M-16FE
16 Fast Ethernet
LINK
5
LINK
AC DC
OK OK
3
4
LINK
2
CSS5-10M-16FE
Gigabit Ethernet
LINK
CAUTION
8
2
3
9 10
11 12
13 14
15
1
DISCONNECT
POWER SOURCALL
BEFORE SERVICES
ING
7
1
2
CSS5-10M-16FE
LINK
STATUS
16 Fast Ethernet
CONSOLE
System Control
1
SLOT 0
NT
9 10
11 12
13 14
15
SLOT 1
CSS5-10M-16FE
CSS5-SCM-2GE
GE 1
16 Fast Ethernet
LINK/ACT
16 Fast Ethernet
STATUS
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
This section covers:
•
Mid-Mounting the CSS 11506 Mounting Brackets
•
Rack-Mounting the CSS 11506 Chassis
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-17
Chapter 1
Unpacking and Installing the CSS
Installing the CSS 11506
Mid-Mounting the CSS 11506 Mounting Brackets
To change the location of the mounting brackets on the CSS 11506 chassis from
the front-mount position to the mid-mount position:
1.
Remove the four screws securing the mounting bracket from one side of the
chassis, as shown in Figure 1-4.
2.
Move the mounting bracket to the mid-mount position on the CSS, lining up
its screw holes with the holes on the side of the chassis. See Figure 1-5.
Figure 1-5
Mid-Mounting the Mounting Brackets on the CSS 11506
59541
CSS506-SM
CSS506-SM
MANAGEMENT
10BASE-T
CISCO 115
DUPLEX
1
LINK
GE 2
LINK
CONTE
2
3
4
5
6
7
8
PCMCIA
LINK
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
5
6
7
8
DPLX
DPLX
4
5
6
PS1
PS2
PS3
6
7
6
7
8
00 SERIES
SERVIC
ES
SWITC
H
DPLX
DPLX
9 10
11 12
13 14
15
3
4
5
8
DPLX
DPLX
9 10
11 12
13 14
15
CSS5-10M-16FE
16 Fast Ethernet
LINK
5
LINK
AC DC
OK OK
3
4
LINK
2
CSS5-10M-16FE
Gigabit Ethernet
LINK
CAUTION
8
2
3
9 10
11 12
13 14
15
1
LINK
DISCONNECT
POWER SOURCALL
BEFORE SERVICES
ING
7
1
2
CSS5-10M-16FE
LINK
STATUS
16 Fast Ethernet
CONSOLE
System Control
1
SLOT 0
NT
9 10
11 12
13 14
15
SLOT 1
CSS5-10M-16FE
CSS5-SCM-2GE
GE 1
16 Fast Ethernet
LINK/ACT
LINK
16 Fast Ethernet
STATUS
DPLX
DPLX
AC DC
OK OK
AC DC
OK OK
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
3.
Using a Phillips screwdriver, secure the mounting bracket to the CSS.
4.
Repeat steps 1 through 3 to reposition the other mounting bracket on the other
side of the chassis.
To install the chassis in a rack, proceed to the “Rack-Mounting the CSS 11506
Chassis”.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-18
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Rack-Mounting the CSS 11506 Chassis
You are ready to install the CSS in the rack. Before you install the CSS 11506 into
an equipment rack, note the following:
Warning
•
Always install heavier equipment in the lower half of a rack to maintain a low
center of gravity. This practice helps prevent the rack from falling over.
•
Install rack stabilizers (if available) before you mount the chassis.
At least three people are required to mount the chassis in the equipment rack:
two people are needed to hold the chassis in place while a third person
tightens the mounting screws.
To install the CSS 11506 chassis into an equipment rack:
1.
Raise the CSS to the installation height and align the screw holes on the
mounting bracket with the holes on the equipment rack.
2.
Secure each mounting bracket to each side of the rack.
Installing a CSS Module
The modules that you ordered with either the CSS 11503 or CSS 11506 chassis
are preinstalled. If you need to reseat a module, or remove and replace it, refer to
the following sections:
•
Installation Precautions and Restrictions
•
Unpacking a CSS Module
•
Installing a Module
•
Installing a Module
This information applies to the CSS modules only.
If you received an additional module at a later time, it comes with a reference
sheet providing information on the module and how to install it.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-19
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Installation Precautions and Restrictions
This section includes background material related to installing a module into the
CSS chassis. Cisco Systems recommends that you read the topics in this section
before installing a module.
Installation Precautions
Caution
You must power down the CSS before installing or removing a module in a
CSS 11506.
Read and observe the following precautionary information prior to servicing the
CSS.
Warning
Do not remove or install modules without using appropriate anti-static guard
measures. The CSS includes an anti-static wrist strap in the accessory kit.
Attach the copper tape end of the strap to an unpainted metal surface on the
chassis. You can leave the strap connected to the chassis when you are done.
Warning
If you do not power down the CSS, an electrical energy hazard is present within
the chassis. Prior to installing or removing components, remove all metallic
objects from hands and wrists to prevent bridging of live contact points.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-20
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Module Slot Restrictions
Prior to installing a module in a CSS, see Table 1-3 and Table 1-4 for information
on chassis slot restrictions in the CSS 11503 and CSS 11506. I/O modules include
the Fast Ethernet Module (FEM), Gigabit Ethernet Module (GEM), Session
Accelerator Module (SAM), and Secure Socket Layer (SSL) module.
Table 1-3
CSS 11503 Chassis Slot Restriction
Slot Number
Slot Usage
1
Initial active Switch Control Module (SCM)
2
I/O module
3
I/O module
Table 1-4
CSS 11506 Chassis Slot Restriction
Slot Number
Slot Usage
1
Initial active Switch Control Module (SCM)
2
Initial passive SCM or I/O module
3
I/O module
4
I/O module
5
I/O module
6
I/O module
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-21
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Figure 1-6 illustrates a fully-configured CSS 11503 and its slot locations.
Figure 1-6
Fully-Configured CSS 11503
DUPLEX
GE 2
LINK
CISCO 115
2
3
4
CONTE
5
6
7
8
9 10
11 12
13 14
15
SLOT 1
1
LINK
LINK
DPLX
DPLX
2
3
4
5
6
7
8
NT
00 SERIES
SERVIC
ES
SWITC
H
9 10
11 12
13 14
15
CSS5-10M-16FE
CONSOLE
16 Fast Ethernet
SLOT 0
System Control
3
1
LINK
PCMCIA
CSS5-10M-16FE
2
CSS5-SCM-2GE
GE 1
1
LINK
LINK
DPLX
DPLX
16 Fast Ethernet
LINK/ACT
59549
MANAGEMENT
10BASE-T
STATUS
1
2
1
Slot location 1
2
Slot location 2
3
3
Slot location 3
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-22
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Figure 1-7 illustrates a fully-configured CSS 11506 and its slot locations.
Figure 1-7
Fully-Configured CSS 11506
1
2
3
CSS506-SM
CSS506-SM
MANAGEMENT
10BASE-T
CISCO 115
DUPLEX
1
LINK
GE 2
LINK
CONTE
2
3
4
5
6
7
8
PCMCIA
LINK
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
5
6
7
8
DPLX
DPLX
6
PS1
PS2
PS3
6
7
6
7
8
ES
SWITC
H
DPLX
DPLX
9 10
11 12
13 14
15
3
4
5
DPLX
DPLX
8
9 10
11 12
13 14
15
LINK
LINK
DPLX
DPLX
AC DC
OK OK
AC DC
OK OK
59550
3
5
00 SERIES
SERVIC
CSS5-10M-16FE
16 Fast Ethernet
LINK
5
LINK
AC DC
OK OK
4
4
LINK
2
CSS5-10M-16FE
Gigabit Ethernet
CAUTION
DISCONNECT
POWER SOURCALL
BEFORE SERVICES
ING
8
2
3
9 10
11 12
13 14
15
1
LINK
7
1
2
CSS5-10M-16FE
LINK
STATUS
16 Fast Ethernet
CONSOLE
System Control
1
SLOT 0
NT
9 10
11 12
13 14
15
SLOT 1
CSS5-10M-16FE
CSS5-SCM-2GE
GE 1
16 Fast Ethernet
LINK/ACT
16 Fast Ethernet
STATUS
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
4
5
6
1
Slot location 1
4
Slot location 4
2
Slot location 2
5
Slot location 5
3
Slot location 3
6
Slot location 6
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-23
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Unpacking a CSS Module
To unpack a CSS module:
1.
Verify that the module is the model you ordered by checking the model
number listed on the side of the shipping carton.
2.
Remove the module from the shipping carton, leaving it in its anti-static bag.
3.
Put on the anti-static strap provided with your CSS. For example, wear the
anti-static wrist strap (included in the accessory kit) and stick the copper-tape
end of the strap to an unpainted metal surface on the chassis. Make sure that
the wrist strap makes good contact with your skin.
4.
Remove the module from the anti-static shielding bag and inspect it for
damage.
Always hold the module by the faceplate, being careful not to touch the
components. If the module appears to be damaged, return it to the anti-static
bag, repack it in the shipping carton, and contact your local supplier.
5.
To install a module into the CSS chassis, see “Installing a Module”.
Installing a Module
Caution
You must power down the CSS before installing or removing a module in a
CSS 11506.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-24
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
To install a module:
1.
Properly ground yourself prior to handling the module. For example, wear the
anti-static wrist strap (included in the accessory kit) and stick the copper-tape
end of the strap to an unpainted metal surface on the chassis. Make sure that
the wrist strap makes good contact with your skin.
2.
If necessary, power down the CSS.
3.
Locate an open slot in the chassis for the module. See Table 1-3 to identify
possible slots for the module. If necessary, use a #1 Phillips screwdriver to
remove a blank panel from the chassis to expose a slot for the module.
4.
Insert the module into the board guides at the left and right of the slot. Make
sure that the ejectors are fully extended outward. Slide the module into the
chassis by pressing firmly at the left and right of the faceplate as shown in
Figure 1-8.
Figure 1-8
Installing a Module into a CSS Chassis
CISCO 11
1
CONTE
NT
500 SERIES
SERVIC
ES
9 10
11 12
13 14
15
4
5
6
7
8
2
CSS5-10M-16FE
DPLX
LINK
LINK
9 10
11 12
13 14
15
DPLX
DPLX
59542
3
DPLX
H
16 Fast Ethernet
2
16 Fast Ethernet
1
SWITC
1
Spring-loaded screw (one on
each side)
2
5.
Close both ejectors simultaneously to seat the module connector into the
backplane.
6.
Using a Phillips screwdriver, tighten the spring-loaded screws on the front of
the module faceplate.
7.
Reboot the chassis to activate the module.
Ejector (one on each side), extend
outward during insertion
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-25
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Installing a Passive SCM in a CSS 11506
You can install a passive SCM in a CSS 11506 chassis. A passive module is a
stand-by module in case of an active module failure. As implemented in
WebNS 5.10 and greater, if the active SCM fails:
Note
1.
The CSS reboots and connections are terminated.
2.
The CSS restores all configurations using the startup-config file.
3.
The passive SCM becomes active automatically.
Passive modules do not load share processing functions with the active module.
To install a passive SCM:
1.
Properly ground yourself prior to handling the module.
2.
As defined in Table 1-3, SCMs are restricted to slots 1 or 2.
3.
If necessary, power down the CSS.
4.
If necessary, remove a blank panel from the chassis to expose the slot.
5.
Insert the module into the board guides at the left and right of the slot and
slide it into the chassis by pressing firmly at the left and right of the faceplate.
6.
Extend both ejectors simultaneously to seat the module connector into the
backplane.
7.
Using a Phillips screwdriver, tighten the spring-loaded screws on the front of
the module faceplate.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-26
78-13884-03
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
8.
Optionally, you can install the PCMCIA cover to the front of the disk slots
and secure it with its two spring-loaded screws, as shown in Figure 1-9. The
cover protects the disks in the SCM.
Figure 1-9
Installing a PCMCIA Cover on an SCM
MANAGEM
ENT
10BASE-T
DUPLEX
CSS5-SCM-2GE
GE 1
GE 2
PCMCIA
LINK
SLOT 1
SLOT 0
9.
LINK
CONSOLE
59602
LINK/ACT
System Control
STATUS
Reboot the CSS to initialize the passive SCM.
10. To copy the boot configuration from the active SCM to the passive SCM, use
the passive sync command in boot configuration mode. For more
information, refer to the Content Services Switch Administration Guide.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
1-27
Chapter 1
Unpacking and Installing the CSS
Installing a CSS Module
Cisco 11500 Series Content Services Switch Hardware Installation Guide
1-28
78-13884-03
C H A P T E R
2
Cabling the CSS
This chapter describes the individual CSS interfaces, how to cable the CSS and its
interfaces, how to attach a console for console management, and how to connect
the AC power cord or the DC power cord (CSS 11503 and CSS 11506 only).
This chapter also describes the CSS LEDs and connectors. The information in this
chapter applies to the CSS 11501, CSS 11503, and CSS 11506, except where
noted.
This chapter contains the following sections:
•
Cabling the CSS 11501
•
Cabling the CSS 11503 and CSS 11506 Modules
•
Connecting the Console
•
Connecting the Chassis to Ground
•
Connecting the Power Cord
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-1
Chapter 2
Cabling the CSS
Cabling the CSS 11501
Cabling the CSS 11501
A CSS 11501 is a fully integrated platform, delivering transport and application
(layers 4-7) services for Internet and Intranet data centers. The CSS 11501 is a
single-rack-unit, with 6-Gbps aggregate throughput. The integrated components
in the CSS 11501 contribute to the overall processing and memory needs for flow
set up and flow forwarding.
The fully integrated CSS 11501 is responsible for the following functions:
•
System powerup and boot control
•
Centralized routing table management
•
System-wide connection management
•
An interface to an external Network Management Station
•
Disk management
•
An external RS-232 interface
The CSS 11501 configuration supports:
•
288 MB RAM memory (256 MB of usable memory)
•
Two PCMCIA slots for a hard or flash disk drive for the system software, and
logging and off-line system files. A cover is preinstalled over the slots.
•
RJ-45 RS-232 Console port
•
RJ-45 10-Mbps half-duplex Ethernet management connector
•
RJ-45 RS-232 Diag connector (reserved for field service diagnostic use only).
•
Eight auto-sensing 10/100-Mbps Ethernet (10BASE-T/100BASE-TX) interfaces
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-2
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11501
•
SFP GBIC (1000BASE-SX or LX) with LC-type connectors. The GBIC can
use either:
– Longwave-length SFP GBICs (CSS5-GBIC-LX). The longwave length
transceiver (1000BASE-LX) can reach 550 meters for all multimode
media types. For single-mode fiber, the distance is 5,000 meters.
– Shortwave-length SFP GBICs (CSS5-GBIC-SX). The transceiver
distance can reach from 220 meters to 500 meters, depending on the
quality of the fiber.
Warning
Because invisible radiation may be emitted from the aperture of the port when
no fiber cable is connected, avoid exposure to radiation and do not stare into
open apertures.
The CSS 11501 front panel LEDs indicate chassis and configuration status:
•
Two status module LEDs indicating power and device readiness
•
Link/Act and Duplex LEDs for the Ethernet Management port
•
Link/Act and Duplex LEDs for each Ethernet port
•
Link/Act LED for the SFP GBIC
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-3
Chapter 2
Cabling the CSS
Cabling the CSS 11501
CSS 11501 Connectors and LEDs
The CSS 11501 has all connectors and LEDs on the chassis front panel. Figure 2-1
illustrates the connectors and LEDs on the CSS 11501.
For information on the connector pinouts, refer to Appendix B, Cable Connector
Pinouts.
Figure 2-1
CSS 11501 Connectors and LEDs
6
2
4
1
3
5b
7
8
STATUS
DUPLEX
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
LINK DPLX
PCMCIA
1
10
11
5a
2
3
10/100
CISCO 1150
0
LINK DPLX
CONTE
GE
4
5
6
7
10/100
LINK
NT
S E RV I C
ES
78930
LINK/ACT
CONSOLE
SERIES
SWITC
H
8
9
1
Bicolor status LED
(green and red)
6
RJ-45 Ethernet 10BASE-T/100BASE-TX connectors
1 through 81
2
Amber status LED
7
LC-type SFP GBIC (optional)
3
RJ-45 RS-232 Console connector
8
Link LED for SFP GBIC
4
10-Mbps half-duplex Ethernet
management connector
9
RJ-45 RS-232 Diag connector for field service
diagnostic use only. (A connector cover is provided.
Removing the cover voids the warranty.)
5a
PCMCIA slot 0 containing a flash or 10
hard disk
PCMCIA slot cover
5b
PCMCIA slot 1 (shown empty) for
11
optional installation of a second flash
or hard disk
Recessed button (reserved for field service use only)
1. The Ethernet Link/Act LED and Duplex LED are located at the top of each RJ-45 Ethernet connector and are not visible in this
illustration.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-4
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11501
Table 2-1 describes the CSS 11501 LEDs and their indications.
Table 2-1
CSS 11501 LED Descriptions
LED Name
Color
State
Indicates
Status (left)
Green
Solid
The CSS 11501 is ready.
Variable
blink
Disk activity is occurring.
Slow blink The CSS 11501 failed.
Red
Solid
The CSS 11501 failed the
power-up self test during the boot
process.
Slow blink The CSS 11501 failed.
Status (right)
No color Off
The CSS 11501 failed and has no
power.
Amber
The CSS 11501 is running
power-up self test.
Fast blink
Slow blink The CSS 11501 is offline and
active.
Link/Act
for the Ethernet
Management Port
Green
Duplex
for Ethernet
Management Port
Green
Link/Act
for Ethernet Port
Green
Duplex
for Ethernet Port
Green
Off
There is no link.
On
The link is established but there is
no activity.
Blinking
The link is established with
transmit or receive activity.
Off
Port is operating at half duplex.
On
Port is operating at full duplex.
Off
No link established.
On
Link established but no activity.
Blinking
Link established with transmit or
receive activity.
Off
Port is operating at half duplex.
On
Port is operating at full duplex.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-5
Chapter 2
Cabling the CSS
Cabling the CSS 11501
Table 2-1
CSS 11501 LED Descriptions (continued)
LED Name
Color
State
Indicates
Link /Act
for the Gigabit
Ethernet Port
Green
Off
There is no link.
On
The link exists and
synchronization is achieved.
Blinking
The link is established with
transmit or receive activity.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-6
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Cabling the CSS 11503 and CSS 11506 Modules
The CSS 11503 and CSS 11506 modules have connectors and LEDs on their front
panels. The following sections describe:
•
CSS 11503 and CSS 11506 Module Overview
•
Switch Control Module Connectors and LEDs
•
Fast Ethernet Module Connectors and LEDs
•
Gigabit Ethernet Module Connectors and LEDs
•
Session Accelerator Module LEDs
•
Secure Socket Layer (SSL) Module LEDs
For information on the connector pinouts, refer to Appendix B, Cable Connector
Pinouts.
CSS 11503 and CSS 11506 Module Overview
The CSS 11503 and CSS 11506 are compact modular platforms, delivering
transport and application (layers 4-7) services for Internet and Intranet data
centers. A CSS is a fully-distributed architecture with all modules in the system
contributing to the overall processing and memory needs for flow set up.
Performance increases incrementally as you add modules, and the modules
balance the overall traffic load.
•
The Cisco 11506 is a five-rack unit, supporting six-slots, with 40-Gbps
aggregate throughput. The CSS 11506 requires at least one Switch Control
Module (SCM) and may be configured with a second SCM in standby mode
for redundancy. With the required SCM in one slot, the CSS 11506 has five
additional slots supporting any combination of I/O modules.
•
The Cisco 11503 is a two-rack-unit, supporting three-slots, with 20-Gbps
aggregate throughput. The CSS 11503 requires an SCM and accommodates
any two of the other modules.
Though all modules participate in flow setup, they differ primarily in control
functions, performance, and I/O. Each CSS 11500 module consists of one
high-speed MIPS RISC processor for flow-setup, one network processor for flow
forwarding, one policy co-processor for search operations and a maximum of
288 MB of RDRAM (up to 256 MB of usable memory).
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-7
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
The CSS 11506 not only supports redundancy in SCMs but also supports
redundant power supplies and redundant Switch Modules (20 Gbps each).
The CSS modules are as follows:
•
144 MB or 288 MB (128 MB or 256 MB of usable memory) Switch Control
Module (SCM) with:
– Two 1000-Mbps Ethernet (1000BASE-SX or LX) small-form factor
pluggable gigabit interface converters (SFP GBICs) with LC-type
connectors.
– Two PCMCIA slots for a hard or flash disk drive for the system software,
and logging and off-line system files.
– RJ-45 RS-232 Console port
– 1 RJ-45 10-Mbps half-duplex Ethernet management connector.
•
Switch Module (SM). An SM provides connectivity among the SCM and
IOMs.
– The CSS 11503 has a single integrated SM. A single SM has an aggregate
throughput of 20 Gbps.
– The CSS 11506 has two removable SMs that share the switching
functions. Two SMs provide 40 Gbps aggregate throughput. As
implemented in WebNS 5.10 and greater, if one SM fails, the CSS
reboots and continues to operate through the other SM.
•
Two slots in the CSS 11503 and five slots in the CSS 11506 are configurable
with:
– Fast Ethernet Modules that provide either 8 or 16 auto-sensing
10/100-Mbps Ethernet ( 10BASE-T/100BASE-TX) RJ-45 ports.
– Gigabit Ethernet Modules provides up to two 1000-Mbps Ethernet
(1000BASE-SX or LX) SFP GBICs with LC-type connectors.
– A Session Accelerator Module (SAM) that provides a cost-effective way
to add flow performance when additional connectivity is not required.
Using the same flow setup and forwarding processors as the I/O modules,
it provides the flexibility to optimize the CSS for port density and
performance.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-8
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
– A Secure Socket Layer (SSL) module that functions as an SSL server by
adding security services between the Web browsers (the client) and
HTTP servers. The SSL module is responsible for all user authentication,
public/private key generation, certificate management, and packet
encryption and decryption functions between the client and the server.
Each SSL module terminates SSL connections received from a client.
The CSS 11503 supports a maximum of two SSL modules and the CSS
11506 supports a maximum of four SSL modules. For information on SSL
commands and functions, refer to the Cisco Content Services Switch
Advanced Configuration Guide.
– An additional SCM to serve as a passive redundant module.
Figure 2-2 illustrates a fully-configured CSS 11503 and its components.
Figure 2-2
CSS 11503 Content Services Switch
DUPLEX
1
LINK
GE 2
LINK
2
3
CISCO 115
00
4
CONTE
5
6
7
8
PCMCIA
9 10
11 12
13 14
15
SLOT 1
1
LINK
LINK
DPLX
DPLX
2
3
4
5
6
7
8
NT
SERVIC
ES
SERIES
SWITC
H
9 10
11 12
13 14
15
CSS5-10M-16FE
CONSOLE
16 Fast Ethernet
SLOT 0
System Control
3
CSS5-10M-16FE
2
CSS5-SCM-2GE
GE 1
1
LINK
LINK
DPLX
DPLX
16 Fast Ethernet
LINK/ACT
59549
MANAGEMENT
10BASE-T
STATUS
1
2
3
1
Slot 1 for the SCM only
2
Slot 2 for an I/O module
3
Slot 3 for an I/O module
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-9
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Figure 2-3 illustrates a fully-configured CSS 11506 and its components.
Figure 2-3
CSS 11506 Content Services Switch
2
4
3
5
CSS506-SM
CSS506-SM
MANAGEMENT
10BASE-T
CISCO 115
DUPLEX
LINK
CONTE
3
4
5
6
7
8
1
LINK
STATUS
LINK
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
5
6
7
8
DPLX
DPLX
4
5
6
PS1
PS2
PS3
6
7
6
7
8
00 SERIES
SERVIC
ES
SWITC
H
DPLX
DPLX
9 10
11 12
13 14
15
3
4
5
8
DPLX
DPLX
9 10
11 12
13 14
15
CSS5-10M-16FE
16 Fast Ethernet
LINK
5
LINK
AC DC
OK OK
3
4
LINK
2
CSS5-10M-16FE
Gigabit Ethernet
LINK
CAUTION
8
2
3
9 10
11 12
13 14
15
1
LINK
DISCONNECT
POWER SOURCALL
BEFORE SERVICES
ING
7
1
2
CSS5-10M-16FE
CONSOLE
16 Fast Ethernet
SLOT 0
NT
9 10
11 12
13 14
15
SLOT 1
LINK
DPLX
DPLX
AC DC
OK OK
AC DC
OK OK
59527
GE 2
2
PCMCIA
System Control
1
1
LINK
CSS5-10M-16FE
CSS5-SCM-2GE
GE 1
16 Fast Ethernet
LINK/ACT
16 Fast Ethernet
STATUS
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
6
1
Fan module
4
Slot 2 for an SCM or I/O module
2
Slot 1 for the SCM
5
Slot 61
3
Switch Modules in slots 7 and 8
6
Power supplies 1, 2, and 3
1. Slots 3 through 6 are for I/O modules, including SAMs and SSL modules.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-10
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Switch Control Module Connectors and LEDs
The Switch Control Module (SCM), model CSS5-SCM-2GE, provides master
control and is responsible for the following functions:
•
System powerup and boot control
•
Centralized routing table management
•
System-wide connection management
•
An interface to an external Network Management Station
•
Disk management
•
An external RS-232 interface
A CSS supports a maximum of two SCMs, one active and one passive.
The Switch Control Module contains the following connectors and slots:
Note
•
1 RJ-45 10-Mbps half-duplex Ethernet management connector.
•
1 RJ-45 RS-232 Console connector.
•
1 RJ-45 RS-232 Diag connector (reserved for field service diagnostic use
only).
•
2 SFP GBICs (1000BASE-SX or LX) with LC-type connectors.
•
Two PCMCIA slots for a hard disk or flash disk. A cover is preinstalled over
the slots.
The SCM can have a maximum of two disk drives.
The SCM front panel LEDs indicate module and configuration status:
Warning
•
Two status module LEDs indicating power and module readiness
•
Link/Act and Duplex LEDs for the Ethernet management port
•
Link LEDs for each SFP GBIC
Because invisible radiation may be emitted from the aperture of the port when
no fiber cable is connected, avoid exposure to radiation and do not stare into
open apertures.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-11
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Figure 2-4 illustrates the SCM front panel connectors, PCMCIA slots, and LEDs.
Figure 2-4
Switch Control Module Connectors and LEDs
4
6
3
5
7
11b
MANAGEM
ENT
10BASE-T
DUPLEX
LINK
GE 2
PCMCIA
9
LINK
8
SLOT 1
SLOT 0
10
CONSOLE
12
78993
GE 1
CSS5-SCM-2GE
1
LINK/ACT
System Control
STATUS
2
11a
1
10-Mbps half-duplex Ethernet management
connector
8
RJ-45 RS-232 Console connector
2
Bicolor status LED (green and red)
9
RJ-45 RS-232 Diag connector for field
service diagnostic use only. (A connector
cover is provided. Removing the cover voids
the warranty.)
3
Amber status LED
10
PCMCIA slot cover
4
Link/Act LED
11a PCMCIA slot 0 containing a flash or hard
disk
5
Duplex LED
11b PCMCIA slot 1 (shown empty) for optional
installation of a second flash or hard disk
6
LC-type SFP GBIC (one of two)
12
7
Link LED for the associated SFP GBIC on
the left
Recessed button (reserved for field service
use only)
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-12
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Table 2-2 describes the SCM LEDs and their indications.
Table 2-2
Switch Control Module LED Descriptions
LED Name
Color
State
Indicates
Status (left)
Green
Solid
The module is ready.
Variable
blink
Disk activity is occurring.
Slow blink Another CSS module failed.
Red
Solid
The module failed the power-up
self test during the boot process.
Slow blink The module failed.
Status (right)
No color Off
The module failed and has no
power.
Amber
The module is running power-up
self test.
Fast blink
Slow blink The module is offline and active.
Link/Act
for the Ethernet
Management Port
Link
for each Gigabit
Ethernet Port
Green
Green
Solid
The module is online and not
active (passive SCM).
Off
There is no link.
On
The link is established but there is
no activity.
Blinking
The link is established with
transmit or receive activity.
Off
There is no link.
On
The link exists and
synchronization is achieved.
Blinking
The link is established with
transmit or receive activity.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-13
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Fast Ethernet Module Connectors and LEDs
The FEM is available in two models:
•
Model CSS5-IOM-8FE contains 8 auto-sensing RJ-45 Fast Ethernet
10/100-Mbps 10BASE-T/100BASE-TX connectors.
•
Model CSS5-IOM-16FE contains 16 auto-sensing RJ-45 Fast Ethernet
10/100-Mbps 10BASE-T/100BASE-TX connectors.
Each connector has Link and Duplex LEDs. The LEDs indicate the module and
network status. Figure 2-5 illustrates the LEDs and connectors on the 8-port FEM.
Figure 2-5
8-Port Fast Ethernet Module Connectors and LEDs
2
3
4
LINK
LINK
5
6
7
5
8
DPLX
8 Fast Ethernet
1
2
CSS5-10M-8FE
1
4
DPLX
3
2
59534
3
6
1
RJ-45 Ethernet
10BASE-T/100BASE-TX
connector 1 (connector 2 is
shown directly above it)
4
RJ-45 Ethernet
10BASE-T/100BASE-TX connector
8 (connector 7 is shown directly
below it)
2
Link LED (on each connector)
5
Spring-loaded screw (one of two)
3
Duplex LED (on each
connector)
6
Ejector (one of two)
Figure 2-6 illustrates the LEDs and connectors on the 16-port FEM.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-14
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Figure 2-6
16-Port Fast Ethernet Module Connectors and LEDs
2
3
3
4
5
6
7
8
9 10
11 12
13 14
15
5
LINK
DPLX
DPLX
3
2
59533
LINK
16 Fast Ethernet
1
2
CSS5-10M-16FE
1
4
6
4
1
RJ-45 Ethernet
10BASE-T/100BASE-TX
connector 1 (connector 2 is
shown directly above it)
2
Link LED (on each connector) 5
3
Duplex LED (on each
connector)
6
RJ-45 Ethernet
10BASE-T/100BASE-TX connector
16 (connector 15 is shown directly
below it)
Spring-loaded screw (one of two)
Ejector (one of two)
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-15
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Table 2-3 describes the FEM LEDs and their indications.
Table 2-3
LED Name
Color
State
Indicates
Link
Green
Off
No link established
On
Link established but no activity
Blinking
Link established with transmit or receive
activity
Off
Port is operating at half duplex
On
Port is operating at full duplex
Duplex
Note
Fast Ethernet Module LED Descriptions
Green
If all of the FEM Link and Duplex LEDs blink synchronously, the module has
failed.
Gigabit Ethernet Module Connectors and LEDs
The Gigabit Ethernet Module (GEM), model CSS5-IOM-2GE, contains two
1000-Mbps SFP GBICs with LC-type connectors. The GEM can use either:
Warning
•
Longwave-length SFP GBICs (CSS5-GBIC-LX). The longwave length
transceiver (1000BASE-LX) can reach 550 meters for all multimode media
types. For single-mode fiber, the distance is 5,000 meters.
•
Shortwave-length SFP GBICs (CSS5-GBIC-SX). The transceiver distance
can reach from 220 meters to 500 meters, depending on the quality of the
fiber.
Because invisible radiation may be emitted from the aperture of the port when
no fiber cable is connected, avoid exposure to radiation and do not stare into
open apertures.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-16
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
The GEM front panel LEDs indicate the network status for each of the connectors
(Link LEDs). Figure 2-7 illustrates the LEDs and connectors on a GEM.
Figure 2-7
Gigabit Ethernet Module Connectors and LEDs
3
2
4
4
5
STATUS
GE 1
LINK
LINK
2 Gigabit Ethernet
CSS5-10M-2GE
GE 2
59535
1
6
1
Bicolor status LED (green and
red)
4
Link LED (next to its
corresponding SFP GBIC)
2
Amber status LED
5
Spring-loaded screw (one of two)
3
LC-type SFP GBIC (one of two)
6
Ejector (one of two)
Table 2-4 describes the GEM LEDs.
Table 2-4
Gigabit Ethernet Module LED Descriptions
LED Name
Color
State
Indicates
Status (left)
Green
Solid
The module is ready.
Red
Solid
The module failed the power-up self
test during the boot process.
Slow blink
The module failed.
Status (right)
No color Off
The module failed and has no power.
Amber
Fast blink
The module is running power-up self
test.
Slow blink
The module is offline and active.
Solid
The module is online and not active.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-17
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Table 2-4
Gigabit Ethernet Module LED Descriptions (continued)
LED Name
Color
State
Indicates
Link
Green
Off
There is no link.
On
The link exists and synchronization is
achieved.
Blinking
The link is established with transmit
or receive activity.
Session Accelerator Module LEDs
The Session Accelerator Module (SAM), model CSS5-SAM, is used with the
SCM to provide additional processing support for session setup. The SAM front
panel LEDs indicate its operational status. The SAM has no connectors.
Figure 2-8 illustrates the SAM front panel LEDs.
Figure 2-8
Session Accelerator Module LEDs
2
3
Session Accelerator
CSS5-SAM
59537
STATUS
1
4
1
Bicolor status LED (green and red) 3
2
Amber status LED
4
Spring-loaded screw (one of two)
Ejector (one of two)
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-18
78-13884-03
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Table 2-5 describes the LEDs.
Table 2-5
Session Accelerator Module LED Descriptions
LED Name
Color
State
Indicates
Status
(left)
Green
Solid
The module is ready.
Red
Solid
The module failed the power-up self test
during the boot process.
Slow blink
The module failed.
No color
Off
The module failed and has no power.
Amber
Fast blink
The module is running power-up self test.
Slow blink
The module is offline and active.
Solid
The module is online and not active.
Status
(right)
Secure Socket Layer (SSL) Module LEDs
The Secure Socket Layer (SSL) module, model CSS5-SSL-K9, operates as an
SSL server by adding security services between Web browsers (the client) and
HTTP servers. The SSL module is responsible for all user authentication,
public/private key generation, certificate management, and packet encryption and
decryption functions between the client and the server. Each SSL module
terminates SSL connections received from a client.
The front panel LEDs on the module indicate its operational status. The SSL
module has no connectors.
The CSS 11503 supports a maximum of two SSL modules and the CSS 11506
supports a maximum of four SSL modules.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-19
Chapter 2
Cabling the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Figure 2-9 illustrates the SSL module front panel LEDs.
Figure 2-9
SSL Module LEDs
2
3
Session Accelerator
CSS5-SAM
59537
STATUS
1
4
1
Bicolor status LED (green and red) 3
2
Amber status LED
4
Spring-loaded screw (one of two)
Ejector (one of two)
Table 2-6 describes the LEDs.
Table 2-6
SSL Module LED Descriptions
LED Name
Color
State
Indicates
Status
(left)
Green
Solid
The module is ready.
Red
Solid
The module failed the power-up self test
during the boot process.
Slow blink
The module failed.
No color
Off
The module failed and has no power.
Amber
Fast blink
The module is running power-up self test.
Slow blink
The module is offline and active.
Solid
The module is online and not active.
Status
(right)
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-20
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Console
Connecting the Console
To connect a console to the CSS, attach the console cable (provided in the
accessory kit) to the Console port on the CSS. Your terminal settings must match
the CSS default settings specified in Table 2-7.
Table 2-7
CSS Console Port Default Settings
Parameters
Default Settings
Baud
9600
Data Bits
8
Parity
None
Stop Bits
1
Terminal Type
VT100/ANSI
Flow Control
None
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-21
Chapter 2
Cabling the CSS
Connecting the Chassis to Ground
Connecting the Chassis to Ground
Connecting the CSS 11503 or CSS 11506 chassis to earth ground is required for
all DC-powered installations, and any AC-powered installation where compliance
with Telcordia (formerly Bellcore) grounding requirements is necessary. Have the
recommended tools and supplies available before you begin this procedure (see
Table 2-8).
Warning
Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable
grounding is available.
Tools and Supplies
The accessory kit shipped with the CSS contains the following items used in this
procedure:
•
One 2-hole grounding lug (Panduit no. LCD6-10A-L)
•
Two M5 screws for the grounding lug
Table 2-8 lists the other tools, equipment, and supplies that you need to connect
system ground to the chassis. These are items that you must supply.
Table 2-8
Tools and Supplies
Quantity
Description
Comments
1
Number 2 Phillips screwdriver
—
1
Wire stripping tool
Choose a tool that does not nick
the wire.
Varies
Grounding wire
6 AWG, 0.204 in. (5.18 mm)
recommended. The wire should
have applicable agency
approvals such as Telcordia.
Varies
Screws to attach ground wire to
grounding point at site
Part requirements depend on
location.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-22
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Chassis to Ground
Table 2-8
Tools and Supplies (continued)
Quantity
Description
Comments
1 or 2
2-hole grounding lug. Lug must Recommended types:
fit 6 AWG stranded copper or
• Panduit no. LCD6-10A-L
37/24 flex cables. Each lug must
(1 supplied in accessory
have two holes, centered
kit)
0.625 in. (1.587 cm) apart, and
• Panduit no. LCC6-10A-L
must accept M5 screws.
(long barrel)
One lug is supplied by Cisco
Systems in the accessory kit. The • Thomas & Betts no.
256-30695-1183(*4*)
supplied lug is for the router end
of the ground wire. You may
• Burndy no. YA6CL2TC10
wish to use a lug other than the
one supplied. If you need a lug
for the facility end of the ground
wire, you must supply it.
1
Crimping tool
2
M5 screws with captive, locking Included in accessory kit
washers
shipped with the CSS.
Must fit diameter of grounding
lugs. Cisco Systems
recommends that you use a
crimping tool recommended by
the lug manufacturer.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-23
Chapter 2
Cabling the CSS
Connecting the Chassis to Ground
Attaching the Grounding Cable
The following procedure describes how to attach:
Warning
•
The grounding lug to the grounding cable
•
The grounding cable to the chassis
When you install or replace the unit, the ground connection must always be
made first and disconnected last.
1.
Power off the chassis by setting the power switch (or switches) to the O (off)
position.
2.
Strip the covering from the end of the grounding wire (Figure 2-10). The
amount of covering to be stripped varies depending on the type of lug you
plan to attach to the wire.
Lug
Strip Length
Panduit no. LCD6-10A-L
(supplied in accessory kit)
13/16 inch (2 cm)
Panduit no. LCC6-10A-L
(long barrel)
1 1/16 inch (2.7 cm)
Thomas & Betts no.
256-30695-1183(*4*)
3/4 inch (1.9 cm)
Burndy no. YA6CL2TC10
7/8 inch (2.2 cm)
3.
Insert the stripped end of the grounding wire into the open end of a lug
(Figure 2-10) and crimp the grounding lug securely to the wire. Use the lug
manufacturer’s recommended crimping tool and crimping procedure to
ensure a proper crimp.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-24
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Chassis to Ground
53632
Figure 2-10 Attaching Grounding Wire to Grounding Lug
Stripped wire
4.
Grounding lug
Attach the grounding lug firmly to the threaded holes on the chassis using two
M5 screws.
•
On the CSS 11503 chassis, the holes are located on the left side (looking
from the rear) near the bottom rear corner.
•
On the CSS 11506 chassis, the holes are located on the right rear panel.
The three threaded holes are unevenly spaced to accommodate different lugs.
5.
Strip the covering from the other end of the grounding wire. See the table in
step 2 for strip lengths for different lugs.
6.
Insert the stripped end of the grounding wire into the open end of a grounding
lug and crimp the grounding lug securely to the wire.
7.
Attach the grounding lug to an appropriate grounding point at your site.
8.
Go to the next section, “Connecting the Power Cord”.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-25
Chapter 2
Cabling the CSS
Connecting the Power Cord
Connecting the Power Cord
The CSS 11500 series models are powered by either an AC or DC power supply.
Before you install the AC or DC power cord, ensure that you have read
Appendix A, Specifications, for information on the electrical specifications. The
following sections describe:
•
Connecting a CSS 11501 Power Cord
•
Connecting a CSS 11503 Power Cord
•
Connecting a CSS 11506 Power Cord
•
Checking the DC Power Connection (CSS 11503 and CSS 11506)
Connecting a CSS 11501 Power Cord
To connect an AC power cord to a CSS 11501:
1.
At the rear of the chassis, ensure that the CSS power switch is in the O (off)
position.
2.
Plug the AC power cord connector into the CSS power connector, as shown
in Figure 2-11.
Figure 2-11 Connecting a CSS 11501 AC Power Cord
78677
1
2
1
AC power connector
2
Power switch
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-26
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Power Cord
3.
Plug the power cord into a dedicated 3-wire grounding receptacle.
4.
To power on and boot the CSS, refer to Chapter 3, Booting and Configuring
the CSS.
Connecting a CSS 11503 Power Cord
The following sections provide information on:
•
Connecting a CSS 11503 AC Power Cord
•
Connecting a CSS 11503 DC Power Cord
Connecting a CSS 11503 AC Power Cord
To connect an AC power cord to a CSS 11503:
1.
At the rear of the chassis, ensure that the CSS power switch is in the O (off)
position.
2.
Plug the AC power cord connector into the CSS power connector, as shown
in Figure 2-12.
Figure 2-12 Connecting a CSS 11503 AC Power Cord
1
~
59543
100-240V
50-60 Hz
5A
430 W
2
1
Power switch
2
AC power connector
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-27
Chapter 2
Cabling the CSS
Connecting the Power Cord
3.
Plug the power cord into a dedicated 3-wire grounding receptacle.
4.
To power on and boot the CSS, refer to Chapter 3, Booting and Configuring
the CSS.
Connecting a CSS 11503 DC Power Cord
Before you install a DC power cord, refer to Appendix A, Specifications, for the
DC power supply.
Warning
The DC power supply cord requires at least a 14 AWG wire (maximum 10 AWG
wire). The CSS 11503 draws a maximum of 10 amps.
Warning
Use copper conductors only.
Warning
Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when
connected to power and ground and can cause serious burns or weld the metal
object to the terminals.
Warning
Before performing the DC installation procedure, ensure that power is removed
from the DC circuit. To ensure that all power is off, locate the circuit breaker
that services the DC circuit and switch it off.
Warning
When you are installing or replacing the unit, the ground connection must
always be made first and disconnected last.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-28
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Power Cord
Warning
Only a DC power source that is isolated from AC mains with reinforced
insulation, and that complies with the other safety extra-low voltage (SELV)
requirements in UL1950, CSA 950 3rd Edition, EN 60950, and IEC950, can be
connected to a Cisco 11503 system. This requirement ensures that in a
catastrophic power source fault condition, hazardous voltages are not present
on power terminals and connectors.
To connect the CSS 11503 DC power supply to a power source:
1.
At the rear of the chassis, ensure that the CSS power switch is in the O (off)
position.
2.
Locate the DC terminal block on the rear of the chassis as shown in
Figure 2-13.
Figure 2-13 Location of the CSS 11503 DC Power Supply Connectors
59544
-48/-60V
9.0A,430V
A
1
1
2
Terminal block (–, +, and
)
2
Power switch
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-29
Chapter 2
Cabling the CSS
Connecting the Power Cord
3.
Warning
Using a flat-head screwdriver, loosen the captive screws on the three DC
connectors (labeled from left to right, –, +, and
, respectively).
Before installing a wire, ensure that the polarity of the DC connections is
correct. Reversed polarity causes damage to the DC power supply and can
create a dangerous shock hazard.
Do not consolidate the end of a conductor by soft soldering prior to installation.
4.
Warning
Install the wires into the appropriate connector. Make sure that the
non-insulated part of each wire is 9 mm (0.35 inches) in length.
When installing the wires, always connect the ground wire first. When
disconnecting the wires, always disconnect the ground wire last.
5.
Tighten the captive screws to 5 to 7 inch-pounds (0.6 to 0.8 Nm) of torque to
secure the wires in the connectors. Ensure that the wires are held firmly in
place.
6.
Install the wires to the DC power source.
For the proper power cable wiring between the CSS 11503 and DC power
source, see Table 2-9.
Table 2-9
CSS 11503 to DC Power Source Cabling
CSS 11503
DC Power Source
(Ground)
Warning
(Ground)
+
+
–
–
The proper wiring sequence is ground to ground, positive to positive, and
negative to negative. The ground wire should always be connected first and
disconnected last.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-30
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Power Cord
7.
Switch on the circuit breaker that services the DC circuit.
8.
To check the DC power connection, see “Checking the DC Power Connection
(CSS 11503 and CSS 11506)”.
Connecting a CSS 11506 Power Cord
The following sections provide information for connecting an AC or DC power
cords to a CSS 11506.
•
Connecting a CSS 11506 AC Power Cord
•
Connecting a CSS 11506 DC Power Cord
Connecting a CSS 11506 AC Power Cord
To connect the AC power cord to each power supply in the CSS 11506:
1.
At the front of the supply, ensure that the CSS power switch is in the O (off)
position.
2.
Plug the AC power cord connector into the power connector, as shown in
Figure 2-14.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-31
Chapter 2
Cabling the CSS
Connecting the Power Cord
Figure 2-14 Connecting a CSS 11506 AC Power Cord
1
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
CSS5-10M-16FE
Gigabit Ethernet
2
CAUTION
AC DC
OK OK
DISCONNE
CT ALL
POWER SOU
BEFORE SERRCES
VICING
7
1
8
2
3
4
5
6
PS1
PS2
PS3
AC DC
OK OK
~
59545
100-240V
5A 50-60
Hz
3
1
Power supply LEDs
3
2
Power switch
3.
Plug the power cord into a dedicated 3-wire grounding receptacle.
4.
Repeat steps 1 through 3 for each power supply.
5.
To power on and boot the CSS, refer to Chapter 3, Booting and Configuring
the CSS.
AC power connector
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-32
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Power Cord
Connecting a CSS 11506 DC Power Cord
Before you install a DC power cord, refer to Appendix A, Specifications, for the
DC power supply.
Warning
The DC power supply cord requires at least a 14 AWG wire (maximum 10 AWG
wire). The CSS 11503 draws a maximum of 18 amps.
Warning
Use copper conductors only.
Warning
Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when
connected to power and ground and can cause serious burns or weld the metal
object to the terminals.
Warning
Before performing the DC installation procedure, ensure that power is removed
from the DC circuit. To ensure that all power is off, locate the circuit breaker
that services the DC circuit and switch it off.
Warning
When you are installing or replacing the unit, the ground connection must
always be made first and disconnected last.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-33
Chapter 2
Cabling the CSS
Connecting the Power Cord
Warning
Only a DC power source that is isolated from AC mains with reinforced
insulation, and that complies with the other safety extra-low voltage (SELV)
requirements in UL1950, CSA 950 3rd Edition, EN 60950, and IEC950, can be
connected to a Cisco 11506 system. This requirement ensures that in a
catastrophic power source fault condition, hazardous voltages are not present
on power terminals and connectors.
Warning
This unit might have more than one power supply connection; all connections
must be removed completely for you to completely remove power from the unit.
To connect each CSS 11506 DC power supply to a power source:
1.
On the power supply, ensure that the CSS power switch is in the O (off)
position.
2.
Locate the power supply DC terminal block, as shown in Figure 2-15.
Figure 2-15 Location of CSS 11506 DC Power Supply Connectors
GE 1
2
LINK
1
LINK
Gigabit Ethernet
CSS5-10M-2GE
GE 2
2
3
CSS5-10M-16FE
1
CAUTION
AC
I/P DC
OK OK
DISCONNE
CT ALL
POWER SOU
BEFORE SERRCES
VICING
7
1
8
2
3
4
5
6
PS1
PS2
PS3
AC DC
OK OK
3
~
59546
100-240V
5A
5060
-48/-60VHz
10/8A
Power supply LEDs
2
Power switch
3
Terminal block (–, +, and
)
59199
1
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-34
78-13884-03
Chapter 2
Cabling the CSS
Connecting the Power Cord
Using a flat-head screwdriver, loosen the captive screws on the three DC
connectors (labeled from left to right, –, +, and
, respectively).
9199
3.
Warning
Before installing a wire, ensure that the polarity of the DC connections is
correct. Reversed polarity can cause damage to the DC power supply and can
create a dangerous shock hazard.
Do not consolidate the end of a conductor by soft soldering prior to installation.
4.
Warning
Install the wires into the appropriate connector. Make sure that the
non-insulated part of each wire is 9 mm (0.35 inches) in length.
When installing the wires, always connect the ground wire first. When
disconnecting the wires, always disconnect the ground wire last.
5.
Tighten the captive screws to 5 to 7 inch-pounds (0.6 to 0.8 Nm) of torque to
secure the wires in the connectors. Ensure that the wires are held firmly in
place.
6.
Repeat steps 1 through 5 for each power supply.
7.
Install the three sets of wires to the DC power source.
For the proper power cable wiring between the CSS 11506 and DC power
source, see Table 2-10.
Table 2-10 CSS 11506 to DC Power Source Cabling
CSS 11506
DC Power Source
(Ground)
Warning
(Ground)
+
+
–
–
The proper wiring sequence is ground to ground, positive to positive, and
negative to negative. The ground wire should always be connected first and
disconnected last.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
2-35
Chapter 2
Cabling the CSS
Connecting the Power Cord
8.
Switch on each circuit breaker that services each DC circuit.
9.
To check the DC power connection, see the following section.
Checking the DC Power Connection (CSS 11503 and CSS 11506)
Follow these steps to verify that you have correctly connected DC power to the
CSS 11503 or CSS 11506 chassis:
Warning
1.
Turn on power to the DC circuit or circuits.
2.
Use a voltmeter to check the voltage at the terminal block on the power
supply. Connect the voltmeter’s positive contact to the positive (+) terminal
on the CSS power supply terminal block. Connect the voltmeter’s negative
contact to the negative (–) terminal on the CSS power supply terminal block.
If the power is wired correctly, the voltmeter registers approximately
+48VDC to +56VDC (or battery float voltage).
Do not allow the test probes of the voltmeter to touch each other while they are
touching the power terminals. This is an ENERGY HAZARD to you, to the
voltmeter, and to the wires connecting the CSS to its power source.
3.
To power on and boot the CSS, refer to Chapter 3, Booting and Configuring
the CSS.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
2-36
78-13884-03
C H A P T E R
3
Booting and Configuring the CSS
This chapter describes how to boot the CSS and using the configuration scripts.
This chapter contains the following sections:
•
Powering Up the CSS
•
Powering Down the CSS
•
Booting the CSS for the First Time
•
Logging in to the CSS
•
Using the Configuration Script
For more information on failure errors and messages that can occur during the
boot process, refer to Appendix C, Troubleshooting.
Powering Up the CSS
To power up a CSS:
•
On an AC CSS, toggle the power switch to the 1 (on) position.
– See Figure 2-11 for the location of the CSS 11501 AC power switch.
– See Figure 2-12 for the location of the CSS 11503 AC power switch.
– See Figure 2-14 for the location of the CSS 11506 AC power switch for
each power supply. Power on all of the supplies in the CSS. The AC OK
and DC OK LEDs light up on each power supply. If either LED remains
unlit, refer to Appendix C, Troubleshooting.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-1
Chapter 3
Booting and Configuring the CSS
Powering Down the CSS
•
For a DC CSS, switch on the applicable circuit breakers for the power source.
Then on the CSS, toggle the power switch to the 1 (on) position.
– See Figure 2-13 for the location of the CSS 11503 DC power switch.
– See Figure 2-15 for the location of the CSS 11506 DC power switch for
each power supply. Power on all of the supplies in the CSS. The I/P OK
and DC OK LEDs light up on each power supply. If either LED remains
unlit, refer to Appendix C, Troubleshooting.
The CSS starts the boot process. Proceed to “Booting the CSS for the First Time”.
Powering Down the CSS
To shut down the CSS gracefully and avoid introducing lost or fragmented files,
always use the shutdown command prior to removing power from the CSS.
For example:
(config-boot)# shutdown
Once the CSS shuts down all processes, you can remove power from the CSS.
Booting the CSS for the First Time
When the CSS initially boots up, it:
•
Performs hardware diagnostics.
•
Prompts you to:
– Enter the software license key
– Configure the IP address, subnet mask, and default gateway for the
Ethernet Management port, used for CSS configuration and management
only; this port does not route traffic
– Change the default administrative login name ( admin ) and password
(system)
– Password-protect the Offline Diagnostic Monitor (OffDM) menu
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-2
78-13884-03
Chapter 3
Booting and Configuring the CSS
Booting the CSS for the First Time
Note
When you initially boot a CSS with two PCMCIA disk drives, the drive in slot 0
contains the directories for the system software and the log files. After you log in
to the CSS, you can configure the drive in slot 1 for use through the map
commands, as described in the Cisco Content Services Switch Administration
Guide.
Hardware Initialization and Power-On Diagnostics
When you boot the CSS, it initializes the hardware and performs power-on
diagnostics. The CSS displays the following messages (shown for the CSS 11503
and CSS 11506):
Locked boot flash.
Validating operational boot flash, please wait...
Operational boot flash valid. Jumping to operational boot flash.
Copyright 2002(c), Cisco Systems, Inc.
Operational boot flash.
Attaching interrupt handlers...Done.
Master SCM.
Built Jun 22 2002 @ 15:14:20
Version x.xx Build xx
Then the hardware goes through a series of tests by the Diagnostic Monitor. These
tests perform power-on self tests on the CSS 11501 components, or on the
CSS 11506 or CSS 11506 modules, chassis, and backplane. The asterisks that
appear indicate the completion of each test.
Press <ESC> to enter the Diagnostic Monitor
* * * * * * * * * * * * * *...
Ran 1 times, x tests. Detected 0 errors.
During this time, the Status LEDs on the CSS 11501 or on each CSS 11503 or
CSS 11506 module blink and change color to indicate the stages of the boot
process. The left Status LED is bicolor, green or red. The right Status LED is
amber.
Note
The Ethernet connectors on the CSS 11501 and the 8- and 16-port Fast Ethernet
Modules on the CSS 11503 or CSS 11506 do not have Status LEDs. They have
Link and Duplex LEDs that indicate the state of the connection.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-3
Chapter 3
Booting and Configuring the CSS
Booting the CSS for the First Time
Table 3-1 defines the boot states and the Status LEDs blinking patterns.
Table 3-1
Status LEDs Boot Definitions
State Sequence
1.
LED Color
LED State
Power up, flash scan, and power-on self test
occur.
Amber
Fast blink
Power-on self test detects an error.
Red
Solid
2.
The CSS 11501 or a module in the CSS 11503 or Amber
CSS 11506 is off line and active.
Slow blink
3.
The CSS 1150 or a module in the CSS 11503 or Amber
CSS 11506 module is on line and not active.
Solid
In the CSS 11506, a passive SCM LED remains
in this state and color.
4.
The CSS 11501 or a module in the CSS 11503 or Green
CSS 11506 is on line and active.
Solid
The CSS 11501 or a module in the CSS 11503 or Red
CSS 11506 (except a Fast Ethernet Module)
fails.
Blinking
If a Fast Ethernet Module fails in the CSS 11503
or CSS 11506, all of its Link and Duplex LEDs
blink simultaneously.
In the CSS 11503 or CSS 11506, when the
master SCM in slot 1 detects a module failure, its
Status LED is green and blinks slowly.
When the master SCM in slot 1 fails, the CSS
does not boot unless there is a passive SCM in
slot 2.
5.
Disk activity
Green
Variable
blinking
If an error occurs during a test, the console displays an error message, increments
the detected error counter, and continues to the next test until it completes all of
the power-on self tests. For more information on errors and messages, refer to
Appendix C, Troubleshooting.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-4
78-13884-03
Chapter 3
Booting and Configuring the CSS
Booting the CSS for the First Time
Note
For information on configuring the passive SCM in a CSS 11503 or CSS 11506,
refer to the Cisco Content Services Switch Administration Guide.
Entering Your License Key
When the CSS completes hardware initialization and power-on diagnostics, you
must enter a valid license key for the CSS software. The CSS does not require you
to enter this key on subsequent startups.
Note
Your license key is located on a white label printed with the “S11K-” product code
and is found inside the CSS accessory kit. If you cannot find the software license
key, call the Cisco Technical Assistance Center (TAC) toll free, 24 hours a day, 7
days a week at 1-800-553-2447 or 1-408-526-7209. You can also email TAC at
tac@cisco.com.
The CSS prompts you to accept the license agreement. You must accept the
license agreement or you cannot log into the CSS.
Then the CSS prompts you to enter your license key, as shown below:
Enter Software License Key: xxxxxxxxxxxx
When you enter:
•
A valid license number, the CSS prompts you to enter an IP address for the
Ethernet Management port.
•
An invalid license number, the CSS redisplays the license prompt until you
enter a valid number. If you do not enter a valid license number, you cannot
log in to the CSS.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-5
Chapter 3
Booting and Configuring the CSS
Booting the CSS for the First Time
Note
If you purchased the SSH software option (as part of the Secure Management
option) or the Network Proximity software option, the license key is on the CSS
software license key card. After the CSS has booted and you log in, use the license
command to enter the license key. For example, enter:
# license
Enter Software License Key (q to quit):
At the prompt, enter the 12-digit option license key.
Configuring the Ethernet Management Port
Once you enter a valid license key at the boot prompt, the CSS displays the
following message and prompt:
Use the Ethernet management port IP address to access the Content
Services Switch for configuration and management only. This port does
not route traffic and is not associated with VLAN circuits.
The current address setting (0.0.0.0) disables the Ethernet Management
port.
Do you wish to configure a valid address for the Ethernet management
port [y/n]?
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-6
78-13884-03
Chapter 3
Booting and Configuring the CSS
Booting the CSS for the First Time
Enter:
•
y to configure an IP address, subnet mask, and default gateway for the
Ethernet Management port. The CSS prompts you for an IP address, a subnet
mask, then a default gateway. You must enter a valid IP address or the CSS
repeats the prompt until you do. The CSS does not accept an all zero IP
address.
Note
The Ethernet Management port IP address must be on a different
subnet from any other CSS VLAN circuit subnet. If you do not make
this IP address unique, you will not be able to access the port.
Enter IP Address [0.0.0.0]:
Enter Subnet Mask [0.0.0.0]:
Enter Default Gateway [0.0.0.0]:
•
Note
n to accept the default IP address (0.0.0.0), subnet mask (0.0.0.0), and default
gateway (0.0.0.0) and disable the port. The CSS does not prompt you for an
IP address, subnet mask, and default gateway.
The Ethernet Management port default IP address of 0.0.0.0 disables the
Management port. To enable the Ethernet Management port, use the Offline
Diagnostic Monitor (Offline DM) menu or specify the ip address command in
boot mode. Refer to the Cisco Content Services Switch Administration Guide for
details on setting the Ethernet Management port IP address.
Changing the Default Username and Password
The CSS allows you to change the default username and password.
Access to this device is allowed using the default username and
password. For enhanced security we recommend that you change the
defaults. Do you want to change the defaults now (yes,no):
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-7
Chapter 3
Booting and Configuring the CSS
Booting the CSS for the First Time
Enter:
•
yes to change the username and password. The CSS prompts you for this
information and password confirmation.
Enter <administrator> username:
Enter <administrator> password:
Confirm <administrator> password:
•
no to keep the default username and password.
Password-Protecting the Offline Diagnostic Monitor Menu
The CSS prompts you to password-protect the Offline Diagnostic Monitor
(OffDM) menu.
Set Password Protection for Offline Diagnostic Monitor menu (yes,no)
Caution
Use care when password-protecting the OffDM Main menu and ensure that you
write down the new password. If you lose the new password, it cannot be
recovered and you will be unable to access the OffDM Main menu. The only
solution, at that point, would be to contact the Cisco Technical Assistance Center
(TAC) at 1-800-553-2447 or 1-408-526-7209. You can also email TAC at
tac@cisco.com.
Enter:
•
yes to password-protect the OffDM menu. When you password-protect the
OffDM menu, you need to enter the administrative username and password
each time you access the menu.
The administrative username and password are required to access
the Offline Diagnostic Monitor menu.
Initializing the disk...........OK
For information on the Offline Diagnostic Monitor Menu options, refer to the
Cisco Content Services Switch Administration Guide, Chapter 1, Logging In
and Getting Started.
•
no to disable password-protection on the OffDM menu.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-8
78-13884-03
Chapter 3
Booting and Configuring the CSS
Logging in to the CSS
The CSS then enables you to access the OffDM menu.
Would you like to access the Offline Diagnostic Monitor? (Y <cr>)
To access the OffDM menu, enter y. If you do not wish to access the OffDM menu
after seeing this message, wait for the CSS to boot.
Logging in to the CSS
After the CSS has completed the boot process, it displays the start-up banner,
copyright, and login prompt. If a startup-config is present, the CSS displays the
following message:
Press CTRL-C to abort running the startup-config
When you abort running the startup-config, the CSS does not use the existing
startup-config. It enables you to log in and reconfigure the CSS to create a new
running-config. Use this feature if you misconfigure your startup-config and it
becomes unusable.
When you log in from:
•
A console, the CSS prompts you with the following message:
Press any key to log in.
•
A Telnet session, this message is not displayed.
The CSS prompts you to enter a username and password. Enter the default user
name admin and the default password system as lowercase text, or enter the
administrative username and password you configured during the boot process or
using the OffDM menu. For security purposes, the CSS does not display the
password.
User Access Verification
Username:
Password:
If you connect a console to the CSS after the CSS boots, your screen will be blank.
Press <Enter> to display the username and password prompts.
If the CSS has never been configured, a configuration script runs automatically
and prompts you to enter configuration information. Subsequent logins to the CSS
do not automatically start the configuration script.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-9
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
Using the Configuration Script
The CSS initiates the configuration script automatically when you log in and it
does not detect an existing startup-config file. During the configuration script, you
need to enter the following information:
•
IP address and subnet mask for circuit VLAN1 (all interfaces are assigned to
VLAN1 by default)
•
IP address for the default gateway
•
IP addresses for the servers
•
Virtual IP address (VIP) for the content rule
The configuration script allows you to create services, owners, and content rules
based on your entries and then enables you to:
Note
•
Configure Layer 3 load balancing
•
Configure Layer 5 load balancing
•
Configure Proxy cache
•
Configure Transparent cache
•
Exit from the script and save the information you entered to the
running-config
For information on services, owners, and content rules, refer to the Cisco Content
Services Switch Basic Configuration Guide.
To accept the script default values, press the Enter key at the prompts. To quit the
script, enter q at any prompt.
You may also initiate the configuration script manually by entering the script play
setup command.
To clear an existing running-config, use the clear running-config command from
SuperUser mode. To clear an existing startup-config, use the clear startup-config
command from SuperUser mode.
The following pages show you the entire configuration script including:
•
Bold text to indicate where you enter information
•
Explanations to help you use the script
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-10
78-13884-03
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
##############################################
#Setup Script for the Content Services Switch#
##############################################
Checking for Existing Config...
No startup-config was found, continue with the setup script [y/n]? y
Note: Pressing “q” after any prompt quits setup. Pressing <CR> after
any [y/n] defaults to “y”.
Warning: All circuit VLAN IP addresses must be on a different subnet
than the Ethernet Mgt port IP address. The existing Ethernet Mgt port
IP address is: 10.0.4.251
Add an IP address to VLAN1: [default = 192.168.10.1] 192.168.3.6
Add an IP subnet mask to VLAN1: [default = 255.255.255.0]
Warning: The default gateway IP address must be on the same subnet as
VLAN1. VLAN1 IP address is: 192.168.3.6
Add IP address for default gateway: [default = 192.168.3.2]
192.168.3.3
Pinging the default gateway: 100% Success.
Which feature do you want to configure?
[1]
[2]
[3]
[4]
[5]
Layer3 load balancing
Layer5 load balancing
Proxy cache
Transparent cache
Exit script
If you select option 5 to exit the script, the CSS saves the information you entered
to the running-config and then displays the running-config.
For additional information, see the following sections for:
•
Configuring Layer 3 Load Balancing
•
Configuring Layer 5 Load Balancing
•
Configuring Proxy Cache
•
Configuring Transparent Cache
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-11
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
Configuring Layer 3 Load Balancing
A Layer 3 load-balancing configuration enables the CSS to use a Virtual IP
address (VIP) to load balance Web traffic to Web servers based on IP addresses.
When you select Layer 3 load balancing, the script automatically:
•
Creates an owner (L3_Owner)
•
Creates a Layer 3 content rule (L3_Rule) and defines ArrowPoint Content
Awareness (ACA) as the load balance method
•
Activates the services
•
Activates the content rule
•
Saves the running-config to the startup-config
The script prompts you to configure:
•
Service name (default name is Server1)
•
Service IP address
•
VIP for the content rule
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-12
78-13884-03
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
To configure Layer 3 load balancing, enter 1.
Which feature do you want to configure?
[1]
[2]
[3]
[4]
Layer3 load balancing
Layer5 load balancing
Proxy cache
Transparent cache
Enter the number for the feature you want to configure: 1
To accept the script default values, press the Enter key at the prompts.
Creating Layer3 load balancing
Enter service name: [default = Server1]
Enter service IP address: [default = 192.168.10.3] 192.168.3.58
Create another service? [y/n]? y
Enter service name: [default = Server2]
Enter service IP address: [default = 192.168.10.3] 192.168.3.59
Create another service? [y/n]? n
Enter Virtual IP address for L3_Rule: [default = 192.168.10.4]
192.168.3.6
After the configuration is completed, the script automatically:
•
Displays the running-config
•
Saves the running-config to the startup-config
Showing the Running Config
!Generated MAR 6 17:53:49
!**************** GLOBAL *****************
ip route 0.0.0.0 0.0.0.0 192.168.3.3
!**************** CIRCUIT ****************
circuit VLAN1
ip address 192.168.3.6 255.255.255.0
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-13
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
!**************** SERVICE ****************
service Server1
ip address 192.168.3.58
active
service Server2
ip address 192.168.3.59
active
!**************** OWNER ******************
owner L3_Owner
content L3_Rule
add service Server1
add service Server2
vip address 192.168.3.6
balance aca
active
##########################################
##
Setup Completed Successfully!!!
##
##########################################
For detailed configuration information, refer to the Content
Services Switch Basic Configuration Guide.
Configuring Layer 5 Load Balancing
A Layer 5 load-balancing configuration enables the CSS to use a VIP address to
load balance Web traffic to Web servers based on URLs.
When you select Layer 5 load balancing, the script automatically:
•
Creates an owner (L5_Owner)
•
Creates a Layer 3 content rule (L3_Rule)
•
Creates a Layer 5 content rule (L5_Rule) and defines:
– Protocol tcp
– Port 80
– URL "/*"
– Load balance method as ACA
•
Activates the services
•
Activates the content rule
•
Saves the running-config to the startup-config
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-14
78-13884-03
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
The script prompts you to configure:
•
Service name (default name is Server1)
•
VIP for the content rule
To configure Layer 5 load balancing, enter 2.
Which feature do you want to configure?
[1]
[2]
[3]
[4]
Layer3 load balancing
Layer5 load balancing
Proxy cache
Transparent cache
Enter the number for the feature you want to configure: 2
To accept the script default values, press the Enter key at the prompts.
Creating Layer5 load balancing
Enter service name: [default= Server1]
Enter service IP address: [default = 192.168.10.3] 192.168.3.58
Create another service? [y/n]? n
Enter Virtual IP address for L5_Rule: [default = 192.168.10.4]
192.168.3.8
After the configuration is completed, the script automatically:
•
Displays the running-config
•
Saves the running-config to the startup-config
Showing the Running Config
!Generated MAR 6 17:53:49
!**************** GLOBAL *****************
ip route 0.0.0.0 0.0.0.0 192.168.3.3
!**************** CIRCUIT ****************
circuit VLAN1
ip address 192.168.3.6 255.255.255.0
!**************** SERVICE ****************
service Server1
ip address 192.168.3.58
active
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-15
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
!**************** OWNER ******************
owner L5_Owner
content L3_Rule
add service Server1
vip address 192.168.3.8
balance aca
active
content L5_Rule
add service Server1
vip address 192.168.3.8
protocol tcp
port 80
url "/*"
balance aca
active
##########################################
##
Setup Completed Successfully!!!
##
##########################################
For detailed configuration information, refer to the Content
Services Switch Basic Configuration Guide.
Configuring Proxy Cache
A proxy cache configuration enables the CSS to use a Virtual IP address (VIP) to
load balance Web traffic to proxy cache servers based on domain name.
When you select Proxy Cache, the script automatically:
•
Creates an owner (Proxy_Owner)
•
Creates a content rule (Proxy_Rule) and defines:
– Service type as proxy-cache
– Protocol tcp
– Port 8080
– URL "/*"
– Load balance method as domain
– Application type HTTP
•
Activates the services
•
Activates the content rule
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-16
78-13884-03
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
The script prompts you to configure:
•
Service name (default name is Proxy_Cache1)
•
VIP for the content rule
To configure a proxy cache configuration, enter 3.
Which feature do you want to configure?
[1]
[2]
[3]
[4]
Layer3 load balancing
Layer5 load balancing
Proxy cache
Transparent cache
Enter the number for the feature you want to configure: 3
To accept the script default values, press the Enter key at the prompts.
Creating Proxy Cache Configuration
Enter service name: [default=Proxy_Cache1]
Enter service IP address: [default = 192.168.10.3] 192.168.3.60
Create another service? [y/n]? n
Enter Virtual IP address for Proxy_Rule: [default = 192.168.10.4]
192.168.3.9
After the configuration is completed, the script automatically:
•
Displays the running-config
•
Saves the running-config to the startup-config
Showing the Running Config
!Generated MAR 6 17:53:49
!**************** GLOBAL *****************
ip route 0.0.0.0 0.0.0.0 192.168.3.3
!**************** CIRCUIT ****************
circuit VLAN1
ip address 192.168.3.6 255.255.255.0
!**************** SERVICE ****************
service Proxy_Cache1
ip address 192.168.3.60
type proxy-cache
port 8080
protocol tcp
active
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-17
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
!**************** OWNER ******************
owner Proxy_Owner
content Proxy_Rule
add service Proxy_Cache1
vip address 192.168.3.9
port 8080
protocol tcp
url "/*"
balance domain
application http
active
##########################################
##
Setup Completed Successfully!!!
##
##########################################
For detailed configuration information, refer to the Content
Services Switch Basic Configuration Guide.
Configuring Transparent Cache
A transparent cache configuration enables the CSS to redirect cacheable HTTP
traffic to transparent cache servers based on IP address and port (80). The CSS
directs non-cacheable HTTP traffic to the origin servers.
When you select Transparent Cache, the script automatically:
•
Creates an owner (Transparent_Owner)
•
Creates a content rule (Transparent_Rule) and defines:
– Service type as transparent-cache
– Protocol tcp
– Port 80
– Extension Qualifier List (EQL) named Cacheable that contains the file
types displayed in the sample running-config file
– URL "/*" eql Cacheable
– Load balance method as domain
– Failover type as bypass
– Application type HTTP
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-18
78-13884-03
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
•
Activates the services
•
Activates the content rule
The script enables you to:
•
Configure a service name (Transparent_Cache1)
•
Define whether to direct only cacheable content or all content to the cache
servers
To configure a transparent cache configuration, enter 4.
Which feature do you want to configure?
[1]
[2]
[3]
[4]
Layer3 load balancing
Layer5 load balancing
Proxy cache
Transparent cache
Enter the number for the feature you want to configure: 4
To accept the script default values, press the Enter key at the prompts.
Creating Transparent Cache Configuration
Enter service name: [default = Transparent_Cache1]
Enter service IP address: [default = 0.0.0.0] 192.168.3.7
Create another service? [y/n]? n
Transparent caching can be configured to direct only cacheable content
to the cache server. Non-cacheable content is sent directly to the
origin server.
The alternative is to direct all traffic to the cache server
regardless of whether the content is cacheable.
Should only cacheable content be directed to the cache server? [y/n]?
Enter:
•
y to define URL “/*” as eql-cacheable in the content rule and allow the CSS
to direct only cacheable content to the cache servers
•
n to define URL “/*” in the content rule and allow the CSS to direct all
content to the cache servers
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-19
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
After the configuration is completed, the script automatically:
•
Displays the running-config
•
Saves the running-config to the startup-config
Showing the Running Config
!Generated MAR 6 17:53:49
!**************** GLOBAL *****************
ip route 0.0.0.0 0.0.0.0 192.168.3.3
!**************** CIRCUIT ****************
circuit VLAN1
ip address 192.168.3.6 255.255.255.0
!**************** SERVICE ****************
service Transparent_Cache1
ip address 192.168.3.7
type transparent-cache
port 80
protocol tcp
active
!****************** EQL ******************
eql Cacheable
description "This EQL contains
extensions of cacheable content"
extension pdf "Acrobat"
extension fdf "Acrobat Forms Document"
extension au "Sound audio/basic"
extension bmp "Bitmap Image"
extension z "Compressed data
application/x-compress"
extension gif "GIF Image image/gif"
extension html "Hypertext Markup
Language text/html"
extension htm
extension js "Java script
application/x-javascript"
extension mocha
extension jpeg "JPEG image image/jpeg"
extension jpg
extension jpe
extension jfif
extension pjpeg
extension pjp
extension mp2 "MPEG Audio audio/x-mpeg"
extension mpa
extension abs
extension mpeg "MPEG Video video/mpeg"
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-20
78-13884-03
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
extension mpg
extension mpe
extension mpv
extension vbs
extension m1v
extension pcx "PCX Image"
extension txt "Plain text text/plain"
extension text
extension mov "QuickTime video/quicktime"
extension tiff "TIFF Image image/tiff"
extension tar "Unix Tape Archive
application/x-tar"
extension avi "Video for Windows
video/x-msvideo"
extension wav "Wave File audio/x-wav"
extension gz "application/x-gzip"
extension zip "ZIP file
application/x-zip-compressed"
!***************** OWNER *****************
owner Transparent_Owner
content Transparent_Rule
add service Transparent_Cache1
port 80
protocol tcp
url "/*" eql Cacheable or url "/*"
balance domain
failover bypass
application http
active
##########################################
##
Setup Completed Successfully!!!
##
##########################################
For detailed configuration information, refer to the Content
Services Switch Basic Configuration Guide.
Where to Go Next
Refer to the Cisco Content Services Switch Administration Guide, Cisco Content
Services Switch Basic Configuration Guide, and Cisco Content Services Switch
Advanced Configuration Guide for detailed information on the administration and
configuration of the CSS.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
3-21
Chapter 3
Booting and Configuring the CSS
Using the Configuration Script
Cisco 11500 Series Content Services Switch Hardware Installation Guide
3-22
78-13884-03
A P P E N D I X
A
Specifications
This appendix contains the following sections that list specifications for the
CSS 11501, CSS 11503, and CSS 11506:
•
Electrical Specifications
•
Environmental Specifications
•
Physical Specifications
•
Module Specifications
•
Disk Specifications
•
Supported Standards
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
A-1
Appendix A
Specifications
Electrical Specifications
Electrical Specifications
Table A-1 describes the CSS 11501, CSS 11503, and CSS 11506 AC electrical
specifications.
Table A-1
AC Electrical Specifications
AC Specification
CSS 11501
CSS 11503
CSS 11506
Input Voltage AC
100 to 240 VAC
50 to 60 Hz
100 to 240 VAC
50 to 60 Hz
100 to 240 VAC
50 to 60 Hz
Current AC (max@
100 VAC)
1.6 Amps
5 Amps
9 Amps
Power Consumption
(maximum)
150VA
430VA
860VA
Heat Dissipation
512 BTU/hr
1468 BTU/hr
2939 BTU/hr
Table A-2 describes the CSS 11503 and CSS 11506 DC electrical specifications.
Table A-2
DC Electrical Specifications
DC Specification
CSS 11503
CSS 11506
Voltage DC
-48.0 to -60.0 VDC
-48.0 to -60.0 VDC
Current DC (maximum)
9 Amps
18 Amps
Power Consumption
(maximum)
430 VA
860 VA
Heat Dissipation
1468 BTU/hr
2939 BTU/hr
Cisco 11500 Series Content Services Switch Hardware Installation Guide
A-2
78-13884-03
Appendix A
Specifications
Environmental Specifications
Environmental Specifications
Table A-3 describes the CSS 11501, CSS 11503, and CSS 11506 environmental
specifications.
Table A-3
Environmental Specifications
Specification Operating
Non-operating
Temperature
32° to 104°F (0° to 40°C)
-4° to 149°F (-20° to 64°C)
Humidity
10 to 90% (non-condensing) Up to 95% (non-condensing)
Altitude
0 to 10,000 ft. (0 to 3,000 m) 0 to 15,000 ft. (0 to 4750 m)
Shock
21 inch/sec2 (0.53 m/sec2),
half sine
Vibration
0.35 Grms from 3 to 500 Hz 1.0 Grms from 3 to 500 Hz
Acoustic
Noise
70 dBa, maximum
20 G, 52 inch/sec2 (1.32 m/sec2),
trapezoidal pulse
Not applicable
Note
G is the unit of acceleration due to gravity, where 1 G equals 32.17 ft/sec2
(9.81 m/sec2).
Note
Grms is the root mean square value of acceleration.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
A-3
Appendix A
Specifications
Physical Specifications
Physical Specifications
Table A-4 describes the CSS 11501, CSS 11503, and CSS 11506 physical
specifications.
Table A-4
Physical Specifications
Specification
CSS 11501
CSS 11503
CSS 11506
Chassis Dimensions
(H x W x D)
1.72” x 17.29” x 18.1”
3.5” x 17.25” x 18.5”
8.25” x 17.25” x 14”
42.85 lbs. (19.44 kg)
67.65 lbs. (30.69 kg)
(base system containing
one SCM and two I/O
modules plus accessory
box)
(base system containing
two power supplies,
one SCM, five I/O
modules, and mounting
brackets plus accessory
box)
33.3 lbs.
57.7 lbs.
Chassis Shipping Weight 21.5 lbs. (9.77 kg)
Chassis Weight Fully
Configured
18.0 lbs.
(base system containing (base system containing
one SCM and two I/O
two power supplies,
modules)
one SCM, and five I/O
modules)
Cisco 11500 Series Content Services Switch Hardware Installation Guide
A-4
78-13884-03
Appendix A
Specifications
Module Specifications
Module Specifications
Table A-5 describes the CSS 11503 and CSS 11506 module specifications.
Table A-5
Module Specifications
Specification
CSS 11503
CSS 11506
Slot Configuration
2 slots for I/O modules
with one SCM
5 slots for I/O modules with one SCM
Switch Bandwidth
20 Gbps.
Each slot has two full-duplex 1.6 Gbps
pathways into a full-meshed switch
fabric
40 Gbps.
Each slot has two full-duplex 1.6 Gbps
pathways into a full-meshed switch
fabric
SCM Memory
(RDRAM)
288 MB
(256 MB of usable memory)
288 MB
(256 MB of usable memory)
IOM Memory
(RDRAM)
144 MB default or 288 MB optional
(128 MB or 256 MB of usable
memory, respectively)
144 MB default or 288 MB optional
(128 MB or 256 MB of usable
memory, respectively)
4 slots for I/O modules with two
SCMs (1 active, 1 passive)
SSL Module Memory 512 MB SDRAM
512 MB SDRAM
72 MB RDRAM
72 MB RDRAM
Disk Specifications
Table A-6 defines the specifications for each disk in the CSS 11501 chassis or in
a CSS 11503 or CSS 11506 SCM.
Table A-6
Disk Specifications
Specification
Hard Disk
Flash Disk
Capacity (minimum)
512 MB
256 MB
Interface
PCMCIA ATA
PCMCIA ATA
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
A-5
Appendix A
Specifications
Supported Standards
Supported Standards
The CSS supports the following standards:
•
Transport
•
Network
•
Routing
•
Gateway
•
Application
•
Network Utilities
•
Network Management
Transport
The CSS supports the following transport standards:
•
TCP
•
UDP
Network
The CSS supports the following network standards:
•
Internet Protocol (IP)
•
ICMP
•
Address Resolution Protocol (ARP)
•
Inverse ARP
Cisco 11500 Series Content Services Switch Hardware Installation Guide
A-6
78-13884-03
Appendix A
Specifications
Supported Standards
Routing
The CSS supports the following routing standards:
•
RIP I
•
RIP II
•
OSPF Version 2
Gateway
The CSS supports Network Address Translation (NAT), per RFC 1631 gateway
standards
Application
The CSS supports the following application standards:
•
HTTP 1.0, HTTP 1.1
•
TELNET
•
FTP, TFTP
•
RTP
Network Utilities
The CSS supports the following network utility standards:
•
DNS Client
•
RADIUS Client
•
TACACS+ Client
•
HTTP Client
•
FTP Daemon
•
SNTP
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
A-7
Appendix A
Specifications
Supported Standards
Network Management
The CSS supports the following network management standards:
•
SNMP v1
•
SNMP v2c
Cisco 11500 Series Content Services Switch Hardware Installation Guide
A-8
78-13884-03
A P P E N D I X
B
Cable Connector Pinouts
This appendix contains the following sections that list pinouts for the connectors
used with the CSS 11501, CSS 11503, and CSS 11506:
•
RJ-45 Fast Ethernet Connector Pinouts
•
RJ-45 RS-232 Console Port Pinouts
•
RJ-45 Management Connector Pinouts
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
B-1
Appendix B
Cable Connector Pinouts
RJ-45 Fast Ethernet Connector Pinouts
RJ-45 Fast Ethernet Connector Pinouts
Table B-1 lists the pinouts for the RJ-45 Fast Ethernet connectors on the
CSS 11501 front panel and the 8- and 16-port Fast Ethernet Modules in the
CSS 11503 or CSS 11506 chassis. The 10/100 Mb ports support autocrossover,
allowing a connection to be made to any device using an Ethernet-type cable.
Table B-1
RJ-45 Fast Ethernet Connector Pinouts
Signal Name
RJ-45 Fast Ethernet Pin
Numbers
RX +
1
RX -
2
TX +
3
Unconnected
4
Unconnected
5
TX -
6
Unconnected
7
Unconnected
8
Cisco 11500 Series Content Services Switch Hardware Installation Guide
B-2
78-13884-03
Appendix B
Cable Connector Pinouts
RJ-45 RS-232 Console Port Pinouts
RJ-45 RS-232 Console Port Pinouts
Table B-2 lists the RJ-45 RS-232 Serial connector pinouts for the Console port on
the CSS 11501 front panel and the CSS 11503 or CSS 11506 Switch Control
Module (SCM).
Table B-2
RJ-45 RS-232 Serial Connector Pinouts for the Console Port
Signal Name
Pin Number
RTS
1
DTR
2
TXD
3
GND
4
GND
5
RXD
6
DSR
7
CTS
8
The following sections provide the pinouts for:
•
Connecting the Console Port to a PC
•
Connecting the Console Port to a Terminal
•
Connecting the Console Port to a Modem
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
B-3
Appendix B
Cable Connector Pinouts
RJ-45 RS-232 Console Port Pinouts
Connecting the Console Port to a PC
To connect the console port to a PC running terminal emulation software, use an
RJ-45 to RJ-45 rollover cable and an RJ-45 to DB-9 female DTE adapter labeled
Terminal. The DTE adapter is part of the accessory kit.
Table B-3 lists the signals of the console port and PC console device, and the
pinouts of the rollover cable and the DTE adapter interfaces.
Table B-3
Console Port to PC Signals and Pinouts
Console
Port Signal
RJ-45 Rollover
Console Port to Cable to RJ-45
RJ-45 Rollover DTE Adapter
Pinouts
Cable Pinouts
DB-9 DTE
Adapter to PC
Console
PC Console
Device Pinouts Device Signal
RTS
1
8
8
CTS
DTR
2
7
6
DSR
TXD
3
6
2
RXD
GND
4
5
5
GND
GND
5
4
5
GND
RXD
6
3
3
TXD
DSR
7
3
4
DTR
CTS
8
1
7
RTS
Cisco 11500 Series Content Services Switch Hardware Installation Guide
B-4
78-13884-03
Appendix B
Cable Connector Pinouts
RJ-45 RS-232 Console Port Pinouts
Connecting the Console Port to a Terminal
To connect the console port to a terminal, use an RJ-45 to RJ-45 rollover cable
and an RJ-45 to DB-25 female DTE adapter. The DTE adapter is part of the
accessory kit.
Table B-4 lists the signals of the console port and terminal device, and the pinouts
of the rollover cable and the DTE adapter interfaces.
Table B-4
Console Port to Terminal Signals and Pinouts
Console
Port Signal
RJ-45 Rollover
Console Port to Cable to RJ-45
RJ-45 Rollover DTE Adapter
Pinouts
Cable Pinouts
DB-25 DTE
Adapter to
Terminal
Pinouts
Terminal
Device Signal
RTS
1
8
5
CTS
DTR
2
7
6
DSR
TXD
3
6
3
RXD
GND
4
5
7
GND
GND
5
4
7
GND
RXD
6
3
2
TXD
DSR
7
3
20
DTR
CTS
8
1
4
RTS
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
B-5
Appendix B
Cable Connector Pinouts
RJ-45 RS-232 Console Port Pinouts
Connecting the Console Port to a Modem
To connect the console port to a terminal, use an RJ-45 to RJ-45 rollover cable
and an RJ-45 to DB-25 male DCE adapter.
Table B-5 lists the signals of the console port and modem device, and the pinouts
of the rollover cable and the DCE adapter interfaces.
Table B-5
Console Port to Modem Signals and Pinouts
Console
Port Signal
RJ-45 Rollover
Console Port to Cable to RJ-45
RJ-45 Rollover DCE Adapter
Pinouts
Cable Pinouts
DB-25 DCE
Adapter to
Modem
Pinouts
Modem
Device Signal
RTS
1
8
4
RTS
DTR
2
7
20
DTR
TXD
3
6
3
TXD
GND
4
5
7
GND
GND
5
4
7
GND
RXD
6
3
2
RXD
DSR
7
3
8
DCD
CTS
8
1
5
CTS
Cisco 11500 Series Content Services Switch Hardware Installation Guide
B-6
78-13884-03
Appendix B
Cable Connector Pinouts
RJ-45 Management Connector Pinouts
RJ-45 Management Connector Pinouts
Table B-6 lists the RJ-45 10 Mb Ethernet Management connector pinouts on the
CSS 11501 front panel and the CSS 11503 or CSS 11506 SCM.
Table B-6
RJ-45 Management Connector Pinouts
Signal Name
Pin Number
TX +
1
TX -
2
RX +
3
Unconnected
4
Unconnected
5
RX -
6
Unconnected
7
Unconnected
8
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
B-7
Appendix B
Cable Connector Pinouts
RJ-45 Management Connector Pinouts
Cisco 11500 Series Content Services Switch Hardware Installation Guide
B-8
78-13884-03
A P P E N D I X
C
Troubleshooting
This appendix provides general troubleshooting information for the CSS
components. It includes the following sections:
•
Troubleshooting the Boot Process
•
Troubleshooting the Console Interface
•
Troubleshooting the CSS Power Supply
•
Troubleshooting the CSS Fans
•
Troubleshooting the CSS 11501
•
Troubleshooting the CSS Modules
•
Log File Information
Information in this appendix applies to the CSS 11501, CSS 11503, and
CSS 11506, except where noted.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-1
Appendix C
Troubleshooting
Troubleshooting the Boot Process
Troubleshooting the Boot Process
There are three phases in the boot process during which the CSS runs diagnostic
tests on the hardware and checks the boot configuration. With the CSS 11501, the
internal motherboard boots all components in the chassis and verifies that they are
properly functioning. With the CSS 11503 and CSS 11506, the SCM boots each
module in the chassis and verifies that the module is functioning properly. During
any of these phases, the CSS reports problems through error messages.
The following sections provide information on:
•
Diagnostic Tests for Hardware
•
OffDM Verification of the Boot Configuration Record and Disk
•
CSS 11501 Boot and Verification
•
SCM Boot and Verification of the Modules
For information about the boot process, refer to Chapter 3, Booting and
Configuring the CSS.
Diagnostic Tests for Hardware
At the beginning of the boot process, the CSS performs diagnostic tests on the
hardware. When the CSS powers up, it displays the following messages (shown
for the CSS 11503 and CSS 11506).
BootRom...booting
Copyright 1998 (c), Cisco Systems, Inc.
Locked boot flash.
Validating operational boot flash, please wait...
Operational boot flash valid. Jumping to operational boot flash.
Copyright 1998 (c), Cisco Systems, Inc.
Operational boot flash.
Attaching interrupt handlers...Done.
Master SCM.
Built Jun 22 2001 @ 15:14:20
Version x.xx Build xx
Then the hardware goes through a series of power-on self-tests on the CSS 11501
components or on the CSS 11503 or CSS 11506 modules, chassis, and backplane.
The asterisks that appear indicate the completion of each test.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-2
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the Boot Process
Press <ESC> to enter the Diagnostic Monitor
* * * * * * * * * * * * * *...
Ran 1 times, x tests. Detected 0 errors.
If an error occurs during a test, the console displays an error message, increments
the detected error counter, and continues to the next test until it completes all of
the power-on self tests. The error messages appear in the following format:
>>>>>>>>FAILURE_START
>
>From: Slot Slot_number, CPU Cpu_number
>Level: Failure_level
>Type: Failure_type
>Major Error ID: Maj_Error_id
>Minor Error ID: Min_Error_id
>Test Ref #: Test_reference
>Test: 'Test_name'
>Details:
>
>Failure_details
>
>>>>>>>>>FAILURE_END
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-3
Appendix C
Troubleshooting
Troubleshooting the Boot Process
Table C-1 lists the fields in the error message and describes their meanings.
Table C-1
Fields in the Diagnostic Monitor Error Message
Field
Description
Slot_number
Indicates the slot number reporting the error.
Cpu_number
Indicates the CPU number reporting the error. This field is 1
for boards with a single MIPS CPU.
Failure_level
There are three types of failure levels:
•
Board - The CSS 11501 motherboard or a specific
module in the CSS 11503 or CSS 11506. If the CSS
completes the boot process, but a component or module
has failed, the CSS also generates a boot log message.
•
Backplane - An EEPROM failure is a catastrophic
failure. Obtain technical assistance.
•
Chassis - A fan failure has occurred. After the boot
process has completed, a log message appears with
information on which fan has failed. For information on
troubleshooting a fan failure, see “Troubleshooting the
CSS Fans” later in this appendix.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-4
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the Boot Process
Table C-1
Fields in the Diagnostic Monitor Error Message (continued)
Field
Description
Failure_type
Indicates one of four types of failure, Hardware/Fatal,
Hardware/Non-Fatal, Software/Fatal, and
Software/Non-Fatal.
•
Fatal errors indicate that a CSS 11501 component or a
specific module in the CSS 11503 or CSS 11506 cannot
perform its intended function reliably.
•
Non-Fatal errors indicate that a CSS 11501 component or
a specific module in the CSS 11503 or CSS 11506 is
capable of performing its intended function despite the
errors, but you should repair the problem as soon as
possible.
In the case of fatal and non-fatal errors with the CSS 11501,
obtain technical assistance.
In the case of fatal and non-fatal errors with the CSS 11503
or CSS 11506:
1.
When the CSS completes the boot process, power down
the CSS.
2.
Reseat the failed module.
3.
Power up the CSS.
If reseating the module does not correct its failure, obtain
technical assistance.
Maj_Error_id
Indicates the single reference number that points to a
particular sub-function in the CSS 11501 chassis or a specific
module in the CSS 11503 or CSS 11506.
Min_Error_id
Indicates the sub reference number that points to a particular
verification step within the sub-function.
Test_reference
Indicates the test number associated with a particular test.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-5
Appendix C
Troubleshooting
Troubleshooting the Boot Process
Table C-1
Fields in the Diagnostic Monitor Error Message (continued)
Field
Test_name
Description
Provides the name of the test reporting the error; for example:
Uart Interrupt Test
PHY Reset Test
Failure_details
Provides information about the error; for example:
PHY Reset Register failed to clear. Addr: 0x12345678
Expected: 0x0 Actual:0xf
After the CSS performs the diagnostics, it boots the Offline Diagnostic Monitor
(OffDM) as indicated by the following message:
Booting OffDm @ 0xbfd70000
See the following section for the OffDM verification of the boot configuration
record and disk drive.
If the Booting OffDm message does not appear, a CSS 11501 component failure
or an SCM failure may have occurred; such a failure would not allow a software
download to start.
If this problem occurs for a CSS 11501, obtain technical assistance.
If this problem occurs for a CSS 11503 or CSS 11506:
1.
Power down the CSS.
2.
Reseat the SCM.
3.
Power up the CSS.
If reseating the module does not correct its failure, obtain technical
assistance.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-6
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the Boot Process
OffDM Verification of the Boot Configuration Record and Disk
During OffDM, the CSS checks the configuration record and initializes the disk.
The following sections discuss:
•
Errors in the Boot Configuration Record
•
Failure of the Disk Drive in the SCM
Errors in the Boot Configuration Record
If the CSS detects any errors in the configuration record, a failed message appears
along with information on the configuration parameter in question. The problems
may include a misconfigured IP and subnet address, or there is no primary or
secondary boot record. The CSS does not continue the boot process until the
problem is resolved.
If a failed message occurs:
Note
1.
Enter the OffDM menu and display your current configuration record. For
detailed information on using OffDM, refer to the Cisco Content Services
Switch Administration Guide.
2.
Correct the misconfiguration.
3.
Reboot the CSS.
If a MAC address error occurs, obtain technical assistance.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-7
Appendix C
Troubleshooting
Troubleshooting the Boot Process
Failure of the Disk Drive in the SCM
After the CSS confirms a valid configuration record, it initializes the disk in slot 0
in the CSS 11501 chassis or on the SCM in the CSS 11503 or CSS 11506. If the
disk cannot initialize, the CSS indicates that it has failed. If this occurs:
1.
Enter the OffDM menu. For detailed information on using OffDM, refer to
Cisco Content Services Switch Administration Guide.
2.
Select the disk options from the Advanced Options menu.
3.
Perform a check disk on the disk in slot 0 and, if necessary, reformat the disk.
4.
Reboot the CSS. If the failure is not resolved, obtain technical assistance.
CSS 11501 Boot and Verification
After the CSS 11501 completes the OffDM boot process, the CSS displays the
main banner and starts the Online Diagnostic Monitor (OnDM). During OnDM,
the CSS 11501 downloads software to each component and verifies that each
component is functioning.
If there is a failure on a component, the CSS 11501 attempts the boot process three
times. If the boot is unsuccessful, the CSS generates the following log message
and saves it in the boot.log file:
CHMGR: Slot slot/subslot had diagnostic failures - NOT STARTING UP
If this problem occurs for a CSS 11501, obtain technical assistance.
For information on log files, see “Log File Information”.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-8
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the Boot Process
SCM Boot and Verification of the Modules
After the CSS 11503 or CSS 11506 completes the OffDM boot process, it displays
the main banner and starts the Online Diagnostic Monitor (OnDM). During
OnDM, the SCM downloads software to each of the modules and boots the
modules. Then, the SCM verifies that each module is functioning.
If there is a failure on a module, the SCM attempts to boot the module three times.
If the SCM is unsuccessful, the CSS generates the following log message and
saves it in the boot.log file:
CHMGR: Slot slot/subslot had diagnostic failures - NOT STARTING UP
Then the SCM shuts down the slot and no longer recognizes it. If you use the show
chassis command, the slot does not appear. If a module failure occurs:
1.
Power down the CSS.
2.
Reseat the module.
3.
Power on the CSS.
If reseating the module does not correct its failure, replace the module.
For additional information on troubleshooting the modules during normal CSS
operation, see “Troubleshooting the CSS 11501”. For information on log files, see
“Log File Information”.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-9
Appendix C
Troubleshooting
Troubleshooting the Console Interface
Troubleshooting the Console Interface
Table C-2 lists common communications problems that may exist between the
CSS and a console. Ensure the console settings are configured to:
•
Baud Rate - 9600
•
Data Bits - 8
•
Parity - none
•
Stop Bits -1
•
Flow Control - none
For information on console cable pinouts, refer to Appendix B, Cable Connector
Pinouts.
Table C-2
Troubleshooting the Console Interface
Possible Problem
Recommended Action
Nothing appears on the screen.
Ensure that the RS-232 cable is
securely connected to the console port.
Characters appear on the screen, but
are garbled.
Verify that the CSS and the console
settings match with respect to baud
rate, data bits, stop bits, and parity.
Abbreviated input is used, but pressing Ensure that you enter a sufficient
the tab key does not enter the command number of characters for the CSS to
you want.
distinguish between different
commands and options.
Random characters are lost.
Set the flow command on the console
to XON/XOFF.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-10
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS Power Supply
Troubleshooting the CSS Power Supply
The following sections discuss:
•
Troubleshooting the CSS 11501 Power Supply
•
Troubleshooting the CSS 11503 Power Supply
•
Troubleshooting the CSS 11506 Power Supply
Troubleshooting the CSS 11501 Power Supply
The CSS 11501 has one power supply as part of its chassis. When you power on
the CSS, the indications of a successful power up are that it boots properly and
become operational, and displays the following log message:
CHMGR: All power supplies are present (1).
Note
This message is displayed only if the logging level is set to the Info-6 or Debug-7
level.
If you power on the CSS and it does not boot as indicated by the Status LEDs,
either:
•
There is no power to the power supply. Ensure that the CSS 11501 has power.
Check the power switch, power cord, and power source.
•
The power supply failed, obtain technical assistance.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-11
Appendix C
Troubleshooting
Troubleshooting the CSS Power Supply
Troubleshooting the CSS 11503 Power Supply
The CSS 11503 has one power supply as part of its chassis. When you power on
the CSS, the indications of a successful power up are that its modules boot and
become operational, and the following log message appears:
CHMGR: All power supplies are present (1).
Note
This message is displayed only if the logging level is set to the Info-6 or Debug-7
level.
If you power on the CSS and its modules do not boot as indicated by their Status
LEDs, either:
•
There is no power to the power supply. Ensure that the CSS has power. Check
the power switch, power cord, and power source.
•
The power supply failed. You must replace the CSS chassis.
Troubleshooting the CSS 11506 Power Supply
If the CSS 11506 power supplies power on successfully and the CSS completes
the boot process, the following message appears:
CHMGR: All power supplies are present (3).
Note
This message is displayed only if the logging level is set to the Info-6 or Debug-7
level.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-12
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS Power Supply
A CSS 11506 can contain a maximum of three power supplies, but it requires two
functioning power supplies to guarantee service. Figure C-1 shows the location of
the power supplies.
Figure C-1
Location of the CSS 11506 Power Supplies
CSS506-SM
CSS506-SM
MANAGEMENT
10BASE-T
CISCO 115
DUPLEX
1
LINK
GE 2
LINK
CONTE
2
3
4
5
6
7
8
PCMCIA
LINK
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
5
6
7
8
DPLX
DPLX
5
6
PS2
PS3
7
6
7
8
00 SERIES
SERVIC
ES
SWITC
H
DPLX
DPLX
9 10
11 12
13 14
15
3
4
5
DPLX
DPLX
8
9 10
11 12
13 14
15
LINK
LINK
DPLX
DPLX
AC DC
OK OK
AC DC
OK OK
59603
4
PS1
6
CSS5-10M-16FE
16 Fast Ethernet
LINK
5
LINK
AC DC
OK OK
3
4
LINK
2
CSS5-10M-16FE
Gigabit Ethernet
LINK
CAUTION
8
2
3
9 10
11 12
13 14
15
1
DISCONNECT
POWER SOURCALL
BEFORE SERVICES
ING
7
1
2
CSS5-10M-16FE
LINK
STATUS
16 Fast Ethernet
CONSOLE
System Control
1
SLOT 0
NT
9 10
11 12
13 14
15
SLOT 1
CSS5-10M-16FE
CSS5-SCM-2GE
GE 1
16 Fast Ethernet
LINK/ACT
16 Fast Ethernet
STATUS
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
~
100-240V
5A 50-60
Hz
1
2
1
Power supply 1
2
Power supply 2
3
3
Power supply 3
If the CSS 11506 contains less than three power supplies, a power supply is
powered off, or a power supply module failed, the CSS displays the following
messages:
CHMGR: Missing backup power supply.
CHMGR: Cannot locate power supply: PSnumber.
The PSnumber variable indicates which power supply cannot be found or has
failed.
When this message occurs, view the LEDs on the power supply. Figure C-2 shows
the AC power supply LEDs. These LEDs indicate the power status of the supply.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-13
Appendix C
Troubleshooting
Troubleshooting the CSS Power Supply
CSS 11506 AC Power Supply LEDs
1
GE 1
1
LINK
CSS5-10M-2GE
GE 2
LINK
2
3
4
Gigabit Ethernet
2
CSS5-10M-16FE
Figure C-2
CAUTION
AC DC
OK OK
DISCONNECT
POWER SOU ALL
BEFORE SERRCES
VICING
7
1
8
2
3
4
5
6
PS1
PS2
PS3
AC DC
OK OK
~
59545
100-240V
5A 50-60
Hz
3
1
Power Supply LEDs: AC OK and
DC OK
2
Power switch
3
AC connector
Figure C-3 shows the DC power supply LEDs.
1
CSS 11506 DC Power Supply LEDs
GE 1
2
LINK
1
LINK
Gigabit Ethernet
CSS5-10M-2GE
GE 2
2
3
CSS5-10M-16FE
Figure C-3
CAUTION
AC
I/P DC
OK OK
DISCONNECT
POWER SOU ALL
BEFORE SERRCES
VICING
7
1
8
2
3
4
5
6
PS1
PS2
PS3
AC DC
OK OK
3
~
59546
100-240V
5A
-4850/-660
0VHz
10/8A
1
Power Supply LEDs: I/P OK and
DC OK
2
Power switch
3
Terminal block
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-14
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS Power Supply
Table C-3 describes these LEDs and provide suggestions for correcting problems.
Table C-3
LEDs of the CSS 11506 Power Supply
LED State
AC OK or
I/P OK (DC power supply)
DC OK
On
Possible Problem
Recommended Action
On
There is no problem
with the power source
and the power supply.
Not applicable.
Off
Off
There is no power to the Ensure the supply has power.
power supply.
Check the power switch, power
cord, and power source.
On
Off
The power supply failed. Remove and replace the power
supply. Refer to the reference
sheet that comes with the
replacement supply.
After you install the power supply,
the CSS automatically brings the
power supply into service.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-15
Appendix C
Troubleshooting
Troubleshooting the CSS Fans
Troubleshooting the CSS Fans
The following sections discuss:
•
Troubleshooting the CSS 11501 Chassis Fans
•
Troubleshooting the CSS 11503 Chassis Fans
•
Troubleshooting the CSS 11506 Fan Module
Troubleshooting the CSS 11501 Chassis Fans
The CSS 11501 has six fans. When the CSS starts up and the fans are operational,
the following message appears:
CHMGR: All fans are present (6).
Note
This message is displayed only if the logging level is set to the Info-6 or Debug-7
level.
If a fan fails when the CSS 11501 starts up, or fails during its normal operation,
the following message appears:
CHMGR: Missing fans. Expected 6. Found number.
The number variable indicates the total number of functioning fans. If the
CSS 11501 starts to overheat, the following message appears:
Temperature has reached x celsius for slot number
The x variable indicates the temperature of the CSS 11501.
When a fan failure occurs, obtain technical assistance.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-16
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS Fans
Troubleshooting the CSS 11503 Chassis Fans
The CSS 11503 has four fans, three for cooling the modules and one for the power
supply. When the CSS starts up and fans are operational, the following message
appears:
CHMGR: All fans are present (4).
Note
This message is displayed only if the logging level is set to the Info-6 or Debug-7
level.
If a fan fails when the CSS starts up, or fails during its normal operation, the
following message appears:
CHMGR: Missing fans. Expected 4. Found number.
The number variable indicates the total number of functioning fans. If the
modules start to overheat in the chassis, the following message appears:
Temperature has reached x celsius for slot number
The x variable indicates the temperature of the module. The module in the
designated slot number is running a temperature that is too high.
If the power supply fan fails, the following message appears:
CHMGR: Power Supply Fan Failure.
When a fan failure occurs, you must replace the CSS chassis.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-17
Appendix C
Troubleshooting
Troubleshooting the CSS Fans
Troubleshooting the CSS 11506 Fan Module
The CSS 11506 has three fans in a single fan module. When the CSS starts up and
fans are operational, the following message appears:
CHMGR: All fans are present (3).
Note
This message is displayed only if the logging level is set to the Info-6 or Debug-7
level.
If a fan fails when the CSS starts up, or fails during its normal operation, the
following message appears:
CHMGR: Missing fans. Expected 3. Found number.
The number variable indicates the total number of functioning fans.
If the modules start to overheat in the chassis, the following message appears:
Temperature has reached x celsius for slot number
The x variable indicates the temperature of the module. The module in the
designated slot number is running a temperature that is too high.
When a fan failure occurs, you must replace the fan module to prevent the CSS
modules from overheating.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-18
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS 11501
Troubleshooting the CSS 11501
CSS 11501 status is indicated by the Status LED on the front panel. For
information about the CSS 11501 LEDs, refer to Chapter 2, Cabling the CSS.
Table C-4 provides suggestions for correcting problems that may occur with the
CSS 11501.
Table C-4
Troubleshooting the CSS 11501
Symptom
Recommended Action
At boot up, the following
message appears:
When there is a failure on a CSS 11501
component, the CSS 11501 attempts the boot
process three times. If the boot is unsuccessful,
the CSS generates a log message and saves it in
the boot.log file. Obtain technical assistance.
Refer to the “About This Guide”. For
information on log files, see “Log File
Information”.
CHMGR: Slot slot/subslot
had diagnostic failures NOT STARTING UP
During normal CSS operation, Check the six fans in the chassis. The
the following message appears: CSS 11501 is running at a temperature that is
too high, as indicated by the x variable. When a
Temperature has reached x
fan failure occurs, obtain technical assistance.
celsius for slot number
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-19
Appendix C
Troubleshooting
Troubleshooting the CSS 11501
Table C-4
Troubleshooting the CSS 11501 (continued)
Symptom
Recommended Action
You cannot access log or
archive files on the CSS disk but
traffic is still passed in and out
of the CSS.
Replace the disk containing the files. Remove
the disk and install the replacement in the
CSS 11501. Refer to the reference sheet that
comes with the replacement disk.
After you install the disk in the CSS, you must
wait 10 seconds before you can reseat or
remove it.
If the replacement disk does not have the same
software version that the CSS is running, the
CSS 11501 will not initialize the disk. You
must reboot the CSS and configure a primary
boot record. You can select the CSS software
currently on the disk or instruct the CSS where
to locate the CSS software ADI file to install on
the disk. If you archived an offline version of
your CSS running-config file, copy it back onto
the CSS.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-20
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS Modules
Troubleshooting the CSS Modules
CSS 11503 and CSS 11506 module status is indicated by the Status LED on the
module front panel. For information about the module LEDs, refer to Chapter 2,
Cabling the CSS.
Table C-5 provides suggestions for correcting problems that may occur with the
modules in the CSS 11503 and CSS 11506.
Caution
Note
Do not remove an active module from the CSS. The module must be in a powered
down state as indicated by the show chassis command. Before removing an SM,
power down the CSS.
As implemented in WebNS 5.10 and greater, when a CSS module fails during
normal operations, the CSS reboots.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-21
Appendix C
Troubleshooting
Troubleshooting the CSS Modules
Table C-5
Troubleshooting the CSS Modules
Symptom
At boot up, the following
message appears:
CHMGR: Slot slot/subslot
had diagnostic failures NOT STARTING UP
During normal CSS operation,
the following message appears
and then, the CSS reboots:
ONDM: LifeTick for
Sub-Module in slot/sub-slot
- slot/subslot failed,
resetting..
During normal CSS operation,
the following message appears
and then, the CSS reboots:
ONDM: Port C Path Failure
%s, turning off Focus-C
Port.
During normal CSS operation,
the following message appears
and then, the CSS reboots:
ONDM: Port D Path Failure
%s, turning off Focus-D
Port.
Recommended Action
1.
Power down the CSS.
2.
Reseat the module in its slot.
3.
Power up the CSS to boot the module.
If reseating the module does not correct the
failure, replace the module. Refer to the
reference sheet that comes with the
replacement module.
If the module is not functioning, one of its
Status LED will be Red and blinking slowly. If
it is an FEM, all of its Link and Duplex LEDs
will blink synchronously. When the CSS
reboots, the Status LED is off. Use the show
chassis command to verify the state of the
module.
1.
Replace the module. Refer to the reference
sheet that comes with the replacement
module.
2.
Power up the CSS to boot the module.
The Switch Module in slot 1 failed.
1.
Power down the CSS.
2.
Remove and replace the module. Refer to
the reference sheet that comes with the
replacement module.
3.
Reboot the CSS to boot the module.
The Switch Module in slot 2 failed.
1.
Power down the CSS.
2.
Remove and replace the module. Refer to
the reference sheet that comes with the
replacement module.
3.
Reboot the CSS to boot the module.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-22
78-13884-03
Appendix C
Troubleshooting
Troubleshooting the CSS Modules
Table C-5
Troubleshooting the CSS Modules (continued)
Symptom
Recommended Action
During normal CSS operation,
the following message appears
and then, the CSS reboots:
The Switch Modules in slot 1 and 2 failed.
ONDM: Both Port C and Port
D Focus Connect paths have
failed.
1.
Power down the CSS.
2.
Remove and replace the modules. Refer to
the reference sheet that comes with the
modules.
3.
Reboot the CSS to boot the modules.
During normal CSS operation, Check the fans in the chassis. The module in
the following message appears: the designated slot number is running a
temperature that is too high, indicated by the x
Temperature has reached x
variable.
celsius for slot number
You cannot access log or
archive files on the CSS disk but
traffic is still passed in and out
of the CSS.
•
For a CSS 11503, replace the chassis.
•
For a CSS 11506, replace the fan module.
Refer to the reference sheet that comes
with the replacement module.
Replace the disk containing the files. Remove
the disk and install the replacement in the
SCM. Refer to the reference sheet that comes
with the replacement disk.
After you install the disk in the SCM, you must
wait 10 seconds before you can reseat or
remove it.
If the replacement disk does not have the same
software version that the CSS is running, the
SCM will not initialize the disk. You must
reboot the CSS and configure a primary boot
record. You can select the CSS software
currently on the disk or instruct the CSS where
to locate the CSS software ADI file to install on
the disk. If you archived an offline version of
your CSS running-config file, copy it back onto
the CSS.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-23
Appendix C
Troubleshooting
Log File Information
Log File Information
The CSS provides logging capabilities for debug and system monitoring by
generating the log files described in Table C-6.
Table C-6
CSS Log File Descriptions
Log File Destination
Default
Location
Alternate
Location
Records
Boot.log
Hard disk
and console
or flash disk
and console
None
Results of the boot process.
Boot.bak
Hard disk
and console
or flash disk
and console
None
Backup of a boot log file. Each time
you reboot the CSS, the software
renames the current boot log file to
boot.log.prev and starts a new boot
log file. The CSS overwrites an
existing backup boot log file when it
renames a boot log file.
Sys.log
Hard disk or
flash disk
Console
syslogd
VTY1
VTY2
Log information for user-defined
subsystem or CLI commands. By
default, logging is enabled and logs
subsystem all with level warning.
The CSS creates sys.log to record this
log information.
Log File
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-24
78-13884-03
Appendix C
Troubleshooting
Log File Information
Table C-6
CSS Log File Descriptions (continued)
Log File Destination
Log File
Default
Location
Sys.log.prev Hard disk or
flash disk
Alternate
Location
Console
syslogd
VTY1
VTY2
Records
Backup of a system log file. When a
system log file reaches its maximum
size (50 MB, for a hard disk-based
CSS; 10 MB, for a flash disk-based
CSS), the software renames the
system log file to sys.log.prev and
starts a new system log file. The CSS
overwrites an existing backup system
log file when a system log file is
renamed. When you reboot a CSS, the
software continues to use the existing
system log file until it reaches its
maximum size.
By default, the CSS has boot logging and system logging enabled and writes the
logged information to the log files on the hard disk or flash disk, depending on the
type of storage in your CSS. Log file information is recorded as ASCII text.
Note
If the CSS disk fails, log and archive information cannot be saved to files on the
disk.
For information on:
•
Configuring logging functions and log messages, refer to the Cisco Content
Services Switch Administration Guide
•
Using syslogd, refer to your syslogd daemon reference guide
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
C-25
Appendix C
Troubleshooting
Log File Information
Cisco 11500 Series Content Services Switch Hardware Installation Guide
C-26
78-13884-03
A P P E N D I X
D
Regulatory Compliance and Safety
Information for the Cisco 11500 Series
Content Services Switch
This appendix provides international agency compliance information applicable
to the Cisco Content Services Switches (CSS) 11501, 11503, and 11506.
This appendix also provides translations of safety warnings. Use the information
in this appendix in conjunction with the information contained in the following
guides:
•
Cisco Content Services Switch Administration Guide
•
Cisco Content Services Switch Basic Configuration Guide
•
Cisco Content Services Switch Advanced Configuration Guide
•
Cisco Content Services Switch Command Reference
•
Cisco Content Services Switch Device Management User’s Guide
•
Release Note for the Cisco 11500 Series Content Services Switch
This appendix includes the following sections:
•
Agency Approvals
•
Safety Requirements
•
Translated Safety Warnings
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-1
Appendix D
Agency Approvals
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Agency Approvals
Table D-1 lists the regulatory approval requirements for the Cisco 11500 Series
CSSs.
Table D-1
Regulatory Approval Requirements
Regulatory
Requirement Category
Electromagnetic
Compatibility
(Emissions)
Approval Agency and Requirement
AS/NZS 3548:1995, Class A or CISPR 22:2002
CISPR 22 Class A, 1997
EN55022 or CISPR 22 Class A, Korean Criteria for in
country testing
FCC, 47CFR15 Sub Part B, Class A
EN55022 Class A, 1998
VCCI V-3/2001.4, Class A
CNS13438 (Taiwan)
ICES-003:1998, Class A
EN61000-3-2:2000, Harmonic Current Emissions
EN61000-3-3:1995, Power Line Flicker
Electromagnetic
Compatibility
(Immunity)
EN55024:1998 [Reference]
The equipment complies with the requirements of the
following specifications as defined in the reference:
EN61000-4-2, ESD
EN61000-4-3, Radiated Immunity
EN61000-4-4, Electrical Fast Transients
EN61000-4-5, Surges
EN61000-4-6, Conducted Immunity
EN61000-4-11, Dips, Sags, and Voltage
Interruptions
EN50082-1:1992, Generic Immunity Requirements Light Industrial
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-2
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Agency Approvals
FCC Class A Compliance Notice (United States)
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
You can determine whether your equipment is causing interference by turning it
off. If the interference stops, it was probably caused by the Cisco equipment or
one of its peripheral devices. If the equipment causes interference to radio or
television reception, try to correct the interference by using one or more of the
following measures:
•
Turn the television or radio antenna until the interference stops.
•
Move the equipment to one side or the other of the television or radio.
•
Move the equipment farther away from the television or radio.
•
Plug the equipment into an outlet that is on a different circuit from the
television or radio. (That is, make certain the equipment and the television or
radio are on circuits controlled by different circuit breakers or fuses.)
Modifying the equipment without Cisco's authorization may result in the
equipment no longer complying with FCC requirements for Class A or Class B
digital devices. In that event, your right to use the equipment may be limited by
FCC regulations, and you may be required to correct any interference to radio or
television communications at your own expense.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-3
Appendix D
Agency Approvals
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
FCC Compliance Information Statement (United States)
Cisco 11500 Series Content Services Switches (CSS 11503 and CSS 11506)
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Note: equipment must be installed and operated using the relevant manuals and
must only be installed with the correct cables and connectors. Cisco Systems Inc.
is not responsible for any radio or television interference caused by unauthorized
changes or modifications to this equipment. Unauthorized changes or
modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation I subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Responsible party: Corporate Compliance Manager, Cisco Systems Inc.
Cisco Systems Inc.
170 West Tasman Drive
San Jose, CA 95134
USA
+408 526-7208
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-4
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Agency Approvals
ICES-003 Class A Compliance Notice (Canada)
English Statement of Compliance
This class A digital apparatus complies with Canadian ICES-003.
French Statement of Compliance
Cet appareil numerique de la classe A est conforme a la norme NMB-003 du
Canada
Europe (EU)
This Apparatus complies with EN55022 Class A and EN55024/ EN50082-1
standard requirements in Europe.
CISPR 22 Class A Warning
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-5
Appendix D
Agency Approvals
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
VCCI Class A Warning
Warning
This is a Class A product based on the standard of the Voluntary Control
Council for Interference by Information Technology Equipment (VCCI). If this
equipment is used in a domestic environment, radio disturbance may arise.
When such trouble occurs, the user may be required to take corrective
actions.
Waarschuwing
Dit is een product van klasse A gebaseerd op de VCCI-norm (Voluntary Control
Council for Interference by Information Technology Equipment). Indien deze
apparatuur in een huishoudelijke omgeving wordt gebruikt, kan radiostoring
optreden. Wanneer dit probleem zich voordoet, kan het nodig zijn dat het door
de gebruiker wordt verholpen.
Varoitus
Tämä on "Voluntary Control Council for Interference by Information Technology
Equipment" (VCCI) -standardin mukaisesti luokan A laite. Jos tätä laitetta
käytetään kotiympäristössä, se voi aiheuttaa radiohäiriöitä. Ongelmien
esiintyessä käyttäjän on ehkä ryhdyttävä toimenpiteisiin tilanteen
korjaamiseksi.
Attention
Cet équipement est un produit de la Classe A basé sur les normes du VCCI
(Voluntary Control Council for Interference by Information Technology
Equipment). L'utilisation de cet équipement dans un environnement
domestique risque d'entraîner des brouillages radio-électriques. En présence
de tels brouillages, l'utilisateur sera peut-être amené à prendre des mesures
correctives.
Warnung
Dies ist laut Standard des Voluntary Control Council for Interference by
Information Technology Equipment (VCCI) ein Produkt der Klasse A. Wenn
dieses Gerät in einem häuslichen Umfeld gebaucht wird, können
Radiostörungen auftreten. Sollte das der Fall sein, muß der Benutzer
gegebenenfalls Gegenmaßnahmen ergreifen.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-6
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Agency Approvals
Avvertenza
Il presente è un prodotto di Classe A ai sensi della norma del Voluntary Control
Council for Interference by Information Technology Equipment (VCCI). Se
questa apparecchiatura viene usata in ambito domestico, è possibile che ne
derivino radiointerferenze. In questo caso, è possibile che all’utente venga
richiesto di prendere le opportune misure correttive.
Advarsel
Dette er et klasse A produkt basert på standard for Voluntary Control Council
for Interference by Information Technology Equipment (VCCI). Hvis dette
utstyret bruket i et hjemmemiljø, kan radioforstyrrelser eventuelt oppstå. Når
denne type problemer finner sted, kan det bli nødvendig at brukeren må
benytte seg av korrigerende handlinger.
Aviso
Este é um produto de Classe A baseado na norma do Voluntary Control Council
for Interference by Information Technology Equipment (Conselho de Controlo
Voluntário para a Interferência por Equipamento de Tecnologia de Informação)
(VCCI). Poderão ocorrer interferências de rádio, caso este equipamento seja
utilizado num ambiente doméstico. Quando ocorrer tal problema, o utilizador
poderá ter de tomar medidas correctivas.
Advertencia
Este es un producto de Clase A basado en el estándar del Voluntary Control
Council for Interference by Information Technology Equipment (VCCI ). Si este
equipo se usa en un entorno doméstico, puede provocar radiointerferencias.
Si ocurren tales problemas, el usuario debe tomar medidas correctivas.
Varning!
Detta är en klass A produkt enligt standarden som fastställts av Voluntary
Control Council for Interference by Information Technology Equipment (VCCI).
Om utrustningen används i hemmiljö kan den orsaka radiostörning. Om sådana
problem uppstår kan användaren behöva vidta åtgärder som rättar till
problemet.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-7
Appendix D
Agency Approvals
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Class A Notice for Taiwan and Other Traditional Chinese
Markets
Warning
This is a Class A Information Product, when used in residential environment,
it may cause radio frequency interference, under such circumstances, the
user may be requested to take appropriate countermeasures. Note: Product
BSMI approval license number is on the product label outside the system
enclosure.
Class A EMC Warning
Warning
This is a Class A Device and is registered for EMC requirements for industrial
use. The seller or buyer should be aware of this. If this type was sold or
purchased by mistake, it should be replaced with a residential-use type.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-8
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Safety Requirements
Safety Requirements
This section identifies safety requirements with which Cisco Content Services
Switches comply.
US
UL 60950 Third Edition - Safety of Information Technology Equipment.
Canada
CAN/CSA 22.2 No. 60950-00 Third Edition - Safety of Information Technology
Equipment.
Europe
EN 60950 - Safety of Information Technology Equipment; incorporating
Amendments 1, 2, 3, 4, and 11 with all National Deviations.
IEC 60950 Second Edition - Safety of Information Technology Equipment;
incorporating Amendments 1, 2, 3, and 4.
Mexico
NOM-019-SCFI-1998, Safety of Data Processing Equipment.
Australia
ACA TS001 1997 Test Report and Statement of Compliance AS/NZS3260
incorporating Amendment 1, 2, 3, and 4.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-9
Appendix D
Safety Requirements
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Laser Safety
This section identifies laser safety requirements with which Cisco Content
Services Switches comply.
US
21CFR 1040, Subchapter J
Europe
EN60825-1
EN60825-2
International
IEC60825-1
IEC60825-2
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-10
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Translated Safety Warnings
This section repeats, in multiple languages, the warnings contained in this
publication. In addition, this section contains translated warnings that can be used
with other switch- or router-specific documents, such as those describing the
individual field-replaceable units (FRUs) applicable to a particular switch or
router.
Warning Definition
Warning
This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents. To see translations of the warnings that appear in this
publication, refer to the Regulatory Compliance and Safety Information
document that accompanied this device.
Waarschuwing
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat
werken, dient u zich bewust te zijn van de bij elektrische schakelingen
betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen
om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in
deze publicatie verschijnen, kunt u het document Regulatory Compliance and
Safety Information (Informatie over naleving van veiligheids- en andere
voorschriften) raadplegen dat bij dit toestel is ingesloten.
Varoitus
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa
ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota
selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista
onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten
käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety
Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-11
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Attention
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant causer des blessures ou des dommages corporels. Avant de
travailler sur un équipement, soyez conscient des dangers posés par les
circuits électriques et familiarisez-vous avec les procédures couramment
utilisées pour éviter les accidents. Pour prendre connaissance des traductions
d’avertissements figurant dans cette publication, consultez le document
Regulatory Compliance and Safety Information (Conformité aux règlements et
consignes de sécurité) qui accompagne cet appareil.
Warnung
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die
zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an
irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen
verbundenen Gefahren und der Standardpraktiken zur Vermeidung von
Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen
Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety
Information (Informationen zu behördlichen Vorschriften und Sicherheit), das
zusammen mit diesem Gerät geliefert wurde.
Avvertenza
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe
causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura,
occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente
delle pratiche standard per la prevenzione di incidenti. La traduzione delle
avvertenze riportate in questa pubblicazione si trova nel documento Regulatory
Compliance and Safety Information (Conformità alle norme e informazioni sulla
sicurezza) che accompagna questo dispositivo.
Advarsel
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til
personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de
faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med
vanlig praksis når det gjelder å unngå ulykker. Hvis du vil se oversettelser av
de advarslene som finnes i denne publikasjonen, kan du se i dokumentet
Regulatory Compliance and Safety Information (Overholdelse av forskrifter og
sikkerhetsinformasjon) som ble levert med denne enheten.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-12
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Aviso
Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá
causar danos físicos. Antes de começar a trabalhar com qualquer
equipamento, familiarize-se com os perigos relacionados com circuitos
eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis
acidentes. Para ver as traduções dos avisos que constam desta publicação,
consulte o documento Regulatory Compliance and Safety Information
(Informação de Segurança e Disposições Reguladoras) que acompanha este
dispositivo.
¡Advertencia!
Este símbolo de aviso significa peligro. Existe riesgo para su integridad física.
Antes de manipular cualquier equipo, considerar los riesgos que entraña la
corriente eléctrica y familiarizarse con los procedimientos estándar de
prevención de accidentes. Para ver una traducción de las advertencias que
aparecen en esta publicación, consultar el documento titulado Regulatory
Compliance and Safety Information (Información sobre seguridad y
conformidad con las disposiciones reglamentarias) que se acompaña con este
dispositivo.
Varning!
Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan
leda till personskada. Innan du utför arbete på någon utrustning måste du vara
medveten om farorna med elkretsar och känna till vanligt förfarande för att
förebygga skador. Se förklaringar av de varningar som förkommer i denna
publikation i dokumentet Regulatory Compliance and Safety Information
(Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna
anordning.
Lithium Battery Disposal Warning
Warning
Waarschuwing
Ultimate disposal of this product should be handled according to all national
laws and regulations.
Dit produkt dient volgens alle landelijke wetten en voorschriften te worden
afgedankt.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-13
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Varoitus
Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia kaikkia
valtakunnallisia lakeja ja säännöksiä noudattaen.
Attention
La mise au rebut définitive de ce produit doit être effectuée conformément à
toutes les lois et réglementations en vigueur.
Warnung
Dieses Produkt muß den geltenden Gesetzen und Vorschriften entsprechend
entsorgt werden.
Avvertenza
L'eliminazione finale di questo prodotto deve essere eseguita osservando le
normative italiane vigenti in materia.
Advarsel
Endelig disponering av dette produktet må skje i henhold til nasjonale lover
og forskrifter.
Aviso
A descartagem final deste produto deverá ser efectuada de acordo com os
regulamentos e a legislação nacional.
¡Advertencia!
El desecho final de este producto debe realizarse según todas las leyes y
regulaciones nacionales.
Varning!
Slutlig kassering av denna produkt bör skötas i enlighet med landets alla
lagar och föreskrifter.
Radiation from Open Port Aperture Warning
Warning
Because invisible radiation may be emitted from the aperture of the port when
no fiber cable is connected, avoid exposure to radiation and do not stare into
open apertures.
Waarschuwing
Aangezien onzichtbare straling vanuit de opening van de poort kan komen als
er geen fiberkabel aangesloten is, dient blootstelling aan straling en het
kijken in open openingen vermeden te worden.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-14
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Varoitus
Koska portin aukosta voi emittoitua näkymätöntä säteilyä, kun kuitukaapelia
ei ole kytkettynä, vältä säteilylle altistumista äläkä katso avoimiin aukkoihin.
Attention
Des radiations invisibles à l'œil nu pouvant traverser l'ouverture du port
lorsqu'aucun câble en fibre optique n'y est connecté, il est recommandé de ne
pas regarder fixement l'intérieur de ces ouvertures.
Warnung
Warnung: Aus der Port-Öffnung können unsichtbare Strahlen emittieren,
wenn kein Glasfaserkabel angeschlossen ist. Vermeiden Sie es, sich den
Strahlungen auszusetzen, und starren Sie nicht in die Öffnungen!
Avvertenza
Quando i cavi in fibra non sono inseriti, radiazioni invisibili possono essere
emesse attraverso l'apertura della porta. Evitate di esporvi alle radiazioni e
non guardate direttamente nelle aperture.
Advarsel
Unngå utsettelse for stråling, og stirr ikke inn i åpninger som er åpne, fordi
usynlig stråling kan emiteres fra portens åpning når det ikke er tilkoblet en
fiberkabel.
Aviso
Dada a possibilidade de emissão de radiação invisível através do orifício da
via de acesso, quando esta não tiver nenhum cabo de fibra conectado, deverá
evitar a exposição à radiação e não deverá olhar fixamente para orifícios que
se encontrarem a descoberto.
¡Advertencia!
Debido a que la apertura del puerto puede emitir radiación invisible cuando
no existe un cable de fibra conectado, evite mirar directamente a las
aperturas para no exponerse a la radiación.
Varning!
Osynlig strålning kan avges från en portöppning utan ansluten fiberkabel och
du bör därför undvika att bli utsatt för strålning genom att inte stirra in i
oskyddade öppningar.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-15
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Class 1 Laser Product Warning
Warning
Waarschuwing
Varoitus
Avertissement
Warnung
Avvertenza
Advarsel!
Aviso
¡Advertencia!
Varning!
Class 1 Laser Product
Waarschuwing voor klasse 1 laserprodukten
Lasertuote luokka 1
Produits Laser Class 1
Produkt-Warnhinweis zu Lasergeräten der Klasse 1
Prodotto Laser di Classe 1
Advarsel for laserprodukter i klasse 1
Aviso sobre produtos a laser da Classe 1
É Aviso sobre producto láser de Clase 1
Varning beträffande laserprodukt, klass 1
Qualified Personnel Warning
Warning
Waarschuwing
Only trained and qualified personnel should be allowed to install or replace
this equipment.
Installatie en reparaties mogen uitsluitend door getraind en bevoegd
personeel uitgevoerd worden.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-16
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Varoitus
Avertissement
Achtung
Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai vaihtaa tämän
laitteen.
Tout installation ou remplacement de l'appareil doit être réalisé par du
personnel qualifié et compétent.
Gerät nur von geschultem, qualifiziertem Personal installieren oder
auswechseln lassen.
Avvertenza
Solo personale addestrato e qualificato deve essere autorizzato ad installare
o sostituire questo apparecchio.
Advarsel
Kun kvalifisert personell med riktig opplæring bør montere eller bytte ut dette
utstyret.
Aviso
¡Atención!
Varning
Este equipamento deverá ser instalado ou substituído apenas por pessoal
devidamente treinado e qualificado.
Estos equipos deben ser instalados y reemplazados exclusivamente por
personal técnico adecuadamente preparado y capacitado.
Denna utrustning ska endast installeras och bytas ut av utbildad och
kvalificerad personal.
Two-Person Lifting Warning
Warning
Two people are required to lift the chassis. To prevent injury, keep your back
straight and lift with your legs, not your back.
Waarschuwing
Er zijn twee personen nodig om het chassis op te tillen. Om letsel te
voorkomen dient u uw rug recht te houden en met uw benen te tillen in plaats
van met uw rug.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-17
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Varoitus
Asennuspohjan nostamiseen tarvitaan kaksi henkilöä. Nosta jalkojen (ei
selän) avulla pitäen selkäsi suorana, jotta välttäisit loukkaantumista.
Attention
Le châssis doit être soulevé par au minimum deux personnes. Pour éviter tout
risque d'accident, maintenez le dos droit et poussez sur vos jambes. Ne
soulevez pas l'unité avec votre dos.
Warnung
Um das Chassis anzuheben, sind zwei Leute erforderlich. Um
Verletzungsgefahr auszuschalten, halten Sie den Rücken gerade und heben
Sie mit den Beinen, nicht dem Rücken.
Avvertenza
Per sollevare il chassis occorre l’intervento di due persone. Onde evitare il
rischio di lesioni personali, tenere sempre ben dritta la schiena e piegare solo
le gambe durante il sollevamento in modo da scaricare il peso sulle gambe e
non sulla schiena.
Advarsel
Det er nødvendig at to personer løfter kabinettet. Hold ryggen rett og løft med
beina - ikke ryggen - for å unngå personskade.
Aviso
São necessárias duas pessoas para levantar o chassis. Para evitar lesões,
mantenha as costas direitas e levante o peso com ambas as pernas, sem
forçar as costas.
¡Advertencia!
Se requieren dos personas para elevar el chasis. Para evitar lesiones,
mantenga su espalda en posición recta y levante con sus piernas, no con su
espalda.
Varning!
Det krävs två personer för att lyfta chassit. För att undvika skador ska du hålla
ryggen rak och lyfta med benen, inte ryggen.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-18
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Lightning Activity Warning
Warning
Do not work on the system or connect or disconnect cables during periods of
lightning activity.
Waarschuwing
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te
werken of kabels aan te sluiten of te ontkoppelen.
Varoitus
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita
ukkosilmalla.
Attention
Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant
un orage.
Warnung
Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen
Sie keine ab, wenn es gewittert.
Avvertenza
Non lavorare sul sistema o collegare oppure scollegare i cavi durante un
temporale con fulmini.
Advarsel
Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det
tordner eller lyner.
Aviso
Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau
tempo (trovoada).
¡Advertencia!
No operar el sistema ni conectar o desconectar cables durante el transcurso
de descargas eléctricas en la atmósfera.
Varning!
Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla
loss kablar.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-19
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Jewelry Removal Warning
Warning
Waarschuwing
Before working on equipment that is connected to power lines, remove
jewelry (including rings, necklaces, and watches). Metal objects will heat up
when connected to power and ground and can cause serious burns or weld the
metal object to the terminals.
Alvorens aan apparatuur te werken die met elektrische leidingen is
verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen.
Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn
verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen
voorwerp aan de aansluitklemmen lassen.
Varoitus
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa,
ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien).
Metalliesineet kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan
kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet
kiinni liitäntänapoihin.
Attention
Avant d’accéder à cet équipement connecté aux lignes électriques, ôter tout
bijou (anneaux, colliers et montres compris). Lorsqu’ils sont branchés à
l’alimentation et reliés à la terre, les objets métalliques chauffent, ce qui peut
provoquer des blessures graves ou souder l’objet métallique aux bornes.
Warnung
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen
Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen.
Metallgegenstände erhitzen sich, wenn sie an das Netz und die Erde
angeschlossen werden, und können schwere Verbrennungen verursachen
oder an die Anschlußklemmen angeschweißt werden.
Avvertenza
Prima di intervenire su apparecchiature collegate alle linee di alimentazione,
togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli
oggetti metallici si riscaldano quando sono collegati tra punti di
alimentazione e massa: possono causare ustioni gravi oppure il metallo può
saldarsi ai terminali.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-20
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal
arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som er
koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige
brannskader eller smelte fast til polene.
Aviso
Antes de trabalhar em equipamento que esteja ligado a linhas de corrente,
retire todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os
objectos metálicos aquecerão em contacto com a corrente e em contacto com
a ligação à terra, podendo causar queimaduras graves ou ficarem soldados
aos terminais.
¡Advertencia!
Antes de operar sobre equipos conectados a líneas de alimentación, quitarse
las joyas (incluidos anillos, collares y relojes). Los objetos de metal se
calientan cuando se conectan a la alimentación y a tierra, lo que puede
ocasionar quemaduras graves o que los objetos metálicos queden soldados a
los bornes.
Varning!
Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du
arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt hettas
upp när de kopplas ihop med ström och jord och kan förorsaka allvarliga
brännskador; metallobjekt kan också sammansvetsas med kontakterna.
Reading Instructions Warning
Warning
Read the installation instructions before you connect the system to its power
source.
Waarschuwing
Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding
verbindt.
Varoitus
Attention
Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Avant de brancher le système sur la source d'alimentation, consulter les
directives d'installation.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-21
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Warnung
Lesen Sie die Installationsanweisungen, bevor Sie das System an die
Stromquelle anschließen.
Avvertenza
Consultare le istruzioni di installazione prima di collegare il sistema
all’alimentatore.
Advarsel
Aviso
¡Advertencia!
Varning!
Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Leia as instruções de instalação antes de ligar o sistema à sua fonte de
energia.
Ver las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Läs installationsanvisningarna innan du kopplar systemet till dess
strömförsörjningsenhet.
Disconnect Device Warning
Warning
Waarschuwing
Varoitus
Incorporate a readily accessible two-poled disconnect device into the fixed
wiring.
Er moet een gemakkelijk toegankelijke, tweepolige stroomverbreker
opgenomen zijn in de vaste bedrading.
Kiinteään johdotukseen on liitettävä kaksinapainen kytkinlaite, johon on
helppo päästä käsiksi.
Attention
Un disjoncteur bipolaire facile d’accès doit être intégré dans le câblage fixe.
Warnung
Die feste Verdrahtung muß eine leicht zugängliche, zweipolige
Trennvorrichtung enthalten.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-22
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Avvertenza
Advarsel
Nei cablaggi fissi va incorporato un sezionatore a due poli facilmente
accessibile.
En lett tilgjengelig, topolet frakoblingsenhet må være innebygd i det faste
ledningsnettet.
Aviso
Deverá incorporar-se um dispositivo de desconexão de dois pólos de acesso
fácil, na instalação eléctrica fixa.
¡Advertencia!
El cableado fijo debe incorporar un dispositivo de desconexión de dos polos
y de acceso fácil.
Varning!
En lättillgänglig tvåpolig frånkopplingsenhet måste ingå i den fasta
kopplingen.
Chassis Installation Warning
Warning
At least three people are required to mount the chassis in the equipment rack:
two people are needed to hold the chassis in place while a third person
tightens the mounting screws.
Waarschuwing
Het chassis moet door ten minste drie personen in het apparatuurrek worden
bevestigd. Twee personen houden het chassis in de juiste positie terwijl de
derde de bevestiginsschroeven aandraait.
Varoitus
Attention
Tarvitaan ainakin kolme henkilöä asentamaan asennuspohja
laitteistotelineeseen: kaksi pitää asennuspohjaa paikoillaan ja kolmas
kiristää asennusruuvit.
l faut trois personnes pour monter le châssis dans la baie d'équipement : deux
pour maintenir le châssis en place et une autre pour serrer les vis
d'assemblage.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-23
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Warnung
Avvertenza
Zum Einbauen des Chassis in das Gerätegestell werden mindestens drei
Personen benötigt: Zwei Personen sollten das Chassis festhalten, während
eine dritte Person die Befestigungsschrauben festzieht.
Si richiedono almeno 3 persone per montare il telaio sul rack
dell'equipaggiamento: due persone per reggere il telaio nella giusta posizione
mentre la terza persona serra le viti di montaggio.
Advarsel
Aviso
¡Advertencia!
Varning!
Det trengs minst tre personer for å montere kabinettet i utstyrshyllen. To
personer må holde kabinettet på plass mens en tredje person fester
monteringsskruene.
São necessárias pelo menos três pessoas para montar o chassi no suporte do
equipamento: duas pessoas para segurar o chassi no lugar e uma terceira
pessoa para apertar os parafusos de montagem.
Se necesitan al menos tres personas para montar el chasis sobre el soporte
del equipo: dos personas para mantener el chasis en su lugar y una tercera
persona para ajustar los tornillos de montaje.
Det krävs minst tre personer vid monteringen av chassit i avsett
instrumentrack: två personer som håller chassit på plats medan en tredje
person drar åt monteringsskruvarna.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-24
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Ground Conductor Warning
Warning
Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable
grounding is available.
Waarschuwing
De aardingsleiding mag nooit buiten werking gesteld worden en de
apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze
geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de
bevoegde instantie voor elektrische inspecties of met een elektricien als u er
niet zeker van bent dat er voor passende aarding gezorgd is.
Varoitus
Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein asennettua
maajohdinta. Ota yhteyttä asianmukaiseen sähkötarkastusviranomaiseen tai
sähköasentajaan, jos olet epävarma maadoituksen sopivuudesta.
Attention
Ne jamais rendre inopérant le conducteur de masse ni utiliser l’équipement
sans un conducteur de masse adéquatement installé. En cas de doute sur la
mise à la masse appropriée disponible, s’adresser à l’organisme responsable
de la sécurité électrique ou à un électricien.
Warnung
Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne
einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich
nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie
sich an den zuständigen elektrischen Fachmann oder einen Elektriker.
Avvertenza
Advarsel
Non escludere mai il conduttore di protezione né usare l’apparecchiatura in
assenza di un conduttore di protezione installato in modo corretto. Se non si
sa con certezza che è disponibile un collegamento di messa a terra adeguato,
esaminare le Norme CEI pertinenti o rivolgersi a un elettricista qualificato.
Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert
jordingsleder. Ta kontakt med det riktige organet for elektrisk inspeksjon
eller en elektriker hvis du er usikker på om det finnes velegnet jording.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-25
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Aviso
Nunca anule o condutor à terra nem opere o equipamento sem ter um condutor
à terra adequadamente instalado. Em caso de dúvida em relação ao sistema
de ligação à terra, contacte os serviços locais de inspecção eléctrica ou um
electricista qualificado.
¡Advertencia!
No inhabilitar nunca el conductor de tierra ni hacer funcionar el equipo si no
existe un conductor de tierra instalado correctamente. Póngase en contacto
con una autoridad apropiada de inspección eléctrica o con un electricista
competente si no está seguro de que hay una conexión a tierra adecuada.
Varning!
Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på
lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida
lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker
kontaktas.
Installation and Replacement Warning
Warning
When you install or replace the unit, the ground connection must always be
made first and disconnected last.
Waarschuwing
Bij installatie of vervanging van het toestel moet de aardverbinding altijd het
eerste worden gemaakt en het laatste worden losgemaakt.
Varoitus
Laitetta asennettaessa tai korvattaessa on maahan yhdistäminen aina tehtävä
ensiksi ja maadoituksen irti kytkeminen viimeiseksi.
Attention
Lors de l’installation ou du remplacement de l’appareil, la mise à la terre doit
toujours être connectée en premier et déconnectée en dernier.
Warnung
Der Erdanschluß muß bei der Installation oder beim Austauschen der Einheit
immer zuerst hergestellt und zuletzt abgetrennt werden.
Avvertenza
In fase di installazione o sostituzione dell'unità, eseguire sempre per primo il
collegamento a massa e disconnetterlo per ultimo.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-26
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Når enheten installeres eller byttes, må jordledningen alltid tilkobles først og
frakobles sist.
Ao instalar ou substituir a unidade, a ligação à terra deverá ser sempre a
primeira a ser ligada, e a última a ser desligada.
Al instalar o sustituir el equipo, conecte siempre la toma de tierra al principio
y desconéctela al final.
Vid installation eller utbyte av enheten måste jordledningen alltid anslutas
först och kopplas bort sist.
Use Copper Conductors Only
Warning
Waarschuwing
Varoitus
Use copper conductors only.
Gebruik alleen koperen geleiders.
Käytä vain kuparijohtimia.
Attention
Utilisez uniquement des conducteurs en cuivre.
Warnung
Verwenden Sie ausschließlich Kupferleiter.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Usate unicamente dei conduttori di rame.
Bruk bare kobberledninger.
Utilize apenas fios condutores de cobre.
Emplee sólo conductores de cobre.
Använd endast ledare av koppar.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-27
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Short-Circuit Protection Warning
Warning
This product requires short-circuit (overcurrent) protection to be provided as
part of the building installation. Install only in accordance with national and
local wiring regulations.
Waarschuwing
Voor dit product moet kortsluitbeveiliging (overstroombeveiliging) deel
uitmaken van de installatie in het gebouw. De installatie moet voldoen aan de
nationale en lokale bedradingvoorschriften.
Varoitus
Tämä tuote vaatii suojauksen oikosulkuja (ylivirtaa) vastaan osana asennusta
rakennukseen. Asenna ainoastaan kansallisten ja paikallisten
johdotussäännösten mukaisesti.
Attention
La protection de ce produit contre les courts-circuits (surtensions) doit être
assurée par la configuration électrique du bâtiment. Vérifiez que l'installation
a lieu uniquement en conformité avec les normes de câblage en vigueur au
niveau national et local.
Warnung
Für dieses Produkt ist eine Kurzschlußsicherung (Überstromsicherung)
erforderlich, die als Teil der Gebäudeinstallation zur Verfügung gestellt wird.
Die Installation sollte nur in Übereinstimmung mit den nationalen und
regionalen Vorschriften zur Verkabelung erfolgen.
Avvertenza
Advarsel
Aviso
Questo prodotto richiede una protezione contro i cortocircuiti, da fornirsi
come parte integrante delle dotazioni presenti nell’edificio. Effettuare
l’installazione rispettando le Norme CEI pertinenti.
Dette produktet krever beskyttelse mot kortslutninger (overspenninger) som
en del av installasjonen. Bare installer utstyret i henhold til nasjonale og
lokale krav til ledningsnett.
Este produto requer proteção contra curto-circuitos (sobreintensidade de
corrente), que deve estar instalada nos edifícios. Instale apenas de acordo
com as normas de instalação elétrica nacionais e locais.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-28
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Advertencia
Este producto necesita estar conectado a la protección frente a cortacircuitos
(sobretensiones) que exista en el edificio. Instálelo únicamente en
conformidad con las regulaciones sobre cableado, tanto locales como
nacionales, a las que se tenga que atener.
Varning!
Denna produkt kräver att kortslutningsskydd (överström) tillhandahålles som
en del av byggnadsinstallationen. Installera bara i enlighet med nationella
och lokala kabeldragningsbestämmelser.
Wire Preparation Warning
Warning
Remove the covering from exactly the specified length of each wire. If you
strip too much of the covering, exposed wire protruding from the terminal
block will create an electrical hazard. If you strip too little of the covering, the
wire might not make a good contact with the terminal, or it might not be held
securely in place in the terminal block.
Waarschuwing
Strip de draad over exact de aangegeven lengte. Als u een te groot gedeelte
stript, is een gedeelte van de draad die uit de aansluitstrip komt, onbedekt,
waardoor gevaarlijke situaties kunnen ontstaan. Stript u een te klein
gedeelte, dan is het mogelijk dat de draad geen volledig contact maakt met de
terminal of dat de draad niet goed wordt vastgehouden in de aansluitstrip.
Varoitus
Poista jokaisesta johdosta eristettä täsmälleen määritetynpituiselta
matkalta. Jos poistat eristettä liikaa, liitäntärasiasta mahdollisesti esiin
tulevat paljaat johdot ovat vaarallisia. Jos poistat eristettä liian vähän, johdot
eivät välttämättä saa riittävää kosketusta liitäntään tai ne eivät pysy
turvallisesti paikoillaan liitäntärasiassa.
Attention
Retirez très exactement la longueur spécifiée de la gaine du fil. Si vous retirez
trop de gaine, le fil dénudé dépassant du bloc de jonction constitue un danger
électrique. Si vous ne découvrez pas suffisamment de gaine, la connexion
avec le bloc risque de ne pas être bonne ou le fil risque de ne pas être calé de
façon sûre dans le bloc de jonction.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-29
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Warnung
Entfernen Sie den Kabelmantel von jedem Kabel um genau die angegebene
Länge. Wenn Sie zu viel von der Schutzverkleidung entfernen, besteht die
Gefahr eines elektrischen Schlags durch vom Terminalblock hervorstehende,
ungeschützte Kabel. Wenn Sie zu wenig von dem Mantel entfernen, ist die
Verbindung des Kabels zum oder seine Befestigung am Terminalblock u.U.
mangelhaft.
Avvertenza
Rimuovere la copertura esattamente alla lunghezza specificata di ciascun
cavo. Se il cavo viene scoperto troppo, il filo sporgente dalla morsettiera
potrebbe creare problemi di natura elettrica. Se invece viene scoperto troppo
poco, il filo potrebbe non essere a contatto con la morsettiera oppure
potrebbe non essere mantenuto in posizione in modo sicuro nella morsettiera.
Advarsel
Fjern nøyaktig den angitte lengden med isolasjon fra hver ledning. Hvis du
fjerner for mye isolasjon, vil den uisolerte ledningen som stikker frem fra
terminalblokken utgjøre en fare for elektrisk støt. Hvis du fjerner for lite
isolasjon, risikerer du at ledningen ikke får god kontakt med terminalen eller
at den ikke holdes godt nok på plass i terminalblokken.
Aviso
Remova o revestimento de cada fio no exacto comprimento especificado. Se
cortar demasiado revestimento, as saliências do fio exposto no bloco do
terminal apresentarão perigo de choques eléctricos. Se cortar muito pouco do
revestimento, o fio poderá não fazer o correcto contacto com o terminal, ou
poderá não ficar bem fixo no bloco do terminal.
¡Advertencia!
Quitar la cobertura exactamente del largo especificado para cada cable. Si el
cable queda demasiado expuesto y sobresale de la caja de bornes, podría
significar un peligro eléctrico. Si por el contrario el cable queda poco
expuesto, es posible que no se conecte correctamente a la caja o que no
quede sujeto en una posición segura.
Varning!
Avlägsna höljet från exakt den angivna längden på varje ledning. Om du tar
bort alltför mycket av höljet, kan den blottlagda ledningen som kommer ut från
kopplingssplinten att utgöra en elektrisk fara. Om du tar bort alltför lite av
höljet, kan det hända att ledningen inte får bra kontakt i anslutningen, eller att
den eventuellt inte kan fixeras i kopplingssplinten.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-30
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
DC Power Source Warning
Warning
Only a DC power source that is isolated from AC mains with reinforced
insulation, and that complies with the other safety extra-low voltage (SELV)
requirements in UL950, CSA 950 3rd Edition, EN 60950, and IEC950, can be
connected to a Cisco 11500 system. This requirement assures that in a
catastrophic power source fault condition, hazardous voltages are not present
on power terminals and connectors.
Waarschuwing
Alleen een gelijkstroombron die geïsoleerd is van het wisselstroomnet met
gewapende isolatie en die voldoet aan de andere veiligheidsvereisten voor
extra-laag voltage (SELV) in UL950, CSA 950 3rd Edition, EN 60950 en IEC950
mag op een Cisco 11500 systeem worden aangesloten. Dit vereiste verzekert
dat bij een catastrofale foutconditie van de stroombron er geen gevaarlijke
voltages aanwezig zijn op de stroomaansluitingspunten en connectors.
Varoitus
Cisco 11500 -järjestelmään saa yhdistää vain tasavirtalähteen, joka on
eristetty vaihtovirtalähteistä vahvistetulla eristeellä ja joka noudattaa muita
suojattujen erittäin alhaisen jännitteen (SELV) piirien vaatimuksia (UL950,
CSA 950 3rd Edition, EN 60950 ja IEC950). Tämä vaatimus varmistaa, että
katastrofaalisen virtalähteen virhetilanteen sattuessa ei virtapäätteissä ja
liitännöissä ole vaarallisia jännitteitä.
Attention
Pour éviter toute présence de tension dangereuse dans les terminaux
d’alimentation et dans les connecteurs en cas de panne d’alimentation grave,
le système Cisco 11500 doit être raccordé uniquement à une alimentation CC
séparée du secteur CA par une isolation renforcée, conforme aux autres
recommandations SELV (Safety Extra-Low Voltage) des normes UL950, CSA 950
3rd Edition, EN 60950 et IEC950.
Warnung
Ein Cisco 11500-System darf nur an eine Gleichstrom-Stromquelle
angeschlossen werden, die durch eine verstärkte Isolierung von
Wechselstrom-Hauptleitungen isoliert ist und die mit den anderen
Sicherheitsanforderungen bezüglich Extra-Niederspannung (SELV) in UL950,
CSA 950 3rd Edition, EN 60950 und IEC950 übereinstimmt.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-31
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Avvertenza
Solo un alimentatore elettrico DC isolato dal AC principale con materiale
isolante rinforzato e aderente a altre esigenze di extra-low voltage (SELV) del
UL950, CSA950 3rd Edition, EN 60950 e IEC950, può essere collegato a un
sistema Cisco 11500. Queste esigenze assicurano che in caso l'alimentatore
elettrico dovesse affrontare condizioni catastrofiche, non ci siano rischi di
voltaggi pericolosi sui terminali e connettori elettrici.
Advarsel
Bare likestrømskilder som er isolert fra vekselstrømledninger med ekstra
isolasjon, og som oppfyller andre sikkerhetskrav for lavspenning (SELV) i
UL950, CSA 950 3rd Edition, EN 60950 og IEC950 kan kobles til et Cisco
11500-system. Disse kravene sikrer at hvis det skulle oppstå en katastrofal feil
i en strømkilde, er det ikke farlig spenning tilstede på strømterminaler og
kontakter.
Aviso
Apenas uma fonte de alimentação de energia do circuito de corrente contínua
que esteja isolada da CA através de um isolamento reforçado, e que esteja em
conformidade com os outros requisitos de circuito de tensão extrema inferior
de segurança (SELV) em UL950, CSA 950 3rd Edition, EN 60950 e IEC950, pode
ser conectada ao sistema Cisco 11500. Este requisito assegura que numa
situação de avaria catastrófica de potência, não se encontrem presentes
voltagens perigosas nos terminais e conectores de potência.
¡Advertencia!
Sólo una fuente de alimentación de CC con aislamiento reforzado de las
fuentes principales de corriente alterna y que cumpla con los demás
requisitos de voltajes de seguridad extrabajos (SELV) estipulados en las
normas UL950, CSA 950 3rd Edition, EN 60950 e IEC950 puede conectarse a un
sistema de la serie Cisco 11500. Estos requisitos garantizan que en una
condición de falla catastrófica de la fuente de poder, no existan niveles de
voltaje peligrosos en los terminales y conectores de alimentación.
Varning!
Endast en likströmskälla som är isolerad från nätväxelström med förstärkt
isolering och som uppfyller de andra kraven för SELV-kretsar (skyddskretsar
för mycket låg spänning) i UL950, CSA 950 3rd Edition, EN 60950 och IEC950,
kan anslutas till ett Cisco 11500-system. Detta krav garanterar att farlig
spänning inte kan förekomma på strömterminaler och kontakter under ett
katastrofalt strömkällefel.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-32
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Dual Power Supply Warning
Warning
Waarschuwing
This unit might have more than one power supply connection; all connections
must be removed completely for you to completely remove power from the
unit.
Deze eenheid kan meer dan één stroomtoevoerverbinding hebben; alle
verbindingen moeten volledig worden verwijderd om de stroom van deze
eenheid volledig te verwijderen.
Varoitus
Tässä laitteessa voi olla useita virtalähdekytkentöjä. Kaikki kytkennät on
irrotettava kokonaan, jotta virta olisi täysin katkaistu laitteesta.
Attention
Il se peut que cette unité soit équipée de plusieurs raccordements
d'alimentation. Pour supprimer tout courant électrique de l'unité, tous les
cordons d'alimentation doivent être débranchés.
Warnung
Diese Einheit verfügt u.U. über mehr als einen Stromanschluß; um Strom
gänzlich von der Einheit fernzuhalten, müssen alle Stromzufuhren abgetrennt
sein.
Avvertenza
Advarsel
Aviso
Questa unità potrebbe avere più di una connessione per alimentatore
elettrico; tutte le connessioni devono essere completamente rimosse per
togliere l'elettricità dall'unità.
Denne enheten kan ha mer enn én strømtilkobling. Alle tilkoblinger må kobles
helt fra for å eliminere strøm fra enheten.
Este dispositivo pode possuir mais do que uma conexão de fonte de
alimentação de energia; para poder remover a fonte de alimentação de
energia, deverão ser desconectadas todas as conexões existentes.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-33
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
¡Advertencia!
Varning!
Esta unidad podría tener más de una conexión de suministros de
alimentación; para eliminar la alimentación por completo, deben
desconectarse completamente todas las conexiones.
Denna enhet kanske har mer än en strömförsörjningsanslutning; alla
anslutningar måste vara helt avlägsnade innan strömtillförseln till enheten är
fullständigt bruten.
DC Power Supply Wiring Warning
Warning
The illustration shows the DC power supply terminal block. Wire the DC
power supply as illustrated. The proper wiring sequence is ground to ground,
positive to positive, and negative to negative. The ground wire should always
be connected first and disconnected last.
Waarschuwing
De figuur toont de aansluitstrip van de gelijkstroomvoeding. Breng de
bedrading voor de gelijkstroomvoeding aan zoals aangegeven. De juiste
bedradingsvolgorde is aarde naar aarde, positief naar positief en negatief
naar negatief. Let op dat de aarddraad altijd het eerst verbonden en het laatst
losgemaakt wordt.
Varoitus
Kuva esittää tasavirtalähteen liitäntärasiaa. Liitä tasavirtalähde kuvan
esittämällä tavalla. Oikea kytkentäjärjestys on maajohto maajohtoon,
positiivinen positiiviseen ja negatiivinen negatiiviseen. Ota huomioon, että
maajohto on aina yhdistettävä ensin ja irrotettava viimeisenä.
Attention
La figure illustre le bloc de connexion de l'alimentation en courant continu.
Câbler l'alimentation en courant continu conformément au schéma. La
séquence de câblage à suivre est terre-terre, positif-positif, et
négatif-négatif. Noter que le fil de masse doit toujours être connecté en
premier et déconnecté en dernier.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-34
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Warnung
Die Abbildung zeigt den Terminalblock des Gleichstrom-Netzgeräts.
Verdrahten Sie das Gleichstrom-Netzgerät wie in der Abbildung dargestellt.
Die richtige Verdrahtungsfolge ist Erde an Erde, positiv an positiv und negativ
an negativ. Der Erdungsdraht sollte immer als erster verbunden und als letzter
abgetrennt werden.
Avvertenza
L'illustrazione mostra la morsettiera dell'alimentatore CC. Cablare
l'alimentatore CC come illustrato. La corretta sequenza di cablaggio è da
massa a massa, da positivo a positivo e da negativo a negativo. Tenere
presente che il filo di massa deve sempre essere collegato per primo e
scollegato per ultimo.
Advarsel
Figuren viser likestrømforsyningsenhetens tilkoplingsterminal.
Likestrømforsyningsenheten tilkoples som vist på figuren. Riktig
tilkoplingssekvens er jord til jord, positiv til positv, og negativ til negativ.
Husk at jordingsledningen alltid skal tilkoples først og frakoples sist.
Aviso
A figura mostra o bloco do terminal de fornecimento de corrente contínua.
Ligue o fornecimento de corrente contínua conforme ilustrado. A sequência
correcta de instalação é terra-a-terra, positivo-positivo, e negativo-negativo.
Note que o fio de terra deverá ser sempre o primeiro a ser ligado, e o último a
ser desligado.
¡Advertencia!
La figura muestra la caja de bornes de la fuente de alimentación. Cablear la
fuente de alimentación de corriente continua tal como se muestra. Las
conexiones deben realizarse en el siguiente orden: tierra con tierra, positivo
con positivo y negativo con negativo. Tenga en cuenta que el conductor de
tierra siempre tiene que conectarse el primero y desconectarse el último.
Varning!
Illustrationen visar anslutningsplinten för likströmförsörjningsenheten.
Koppla ledningarna till strömförsörjningsenheten som bilden visar. Korrekt
kopplingssekvens är jord till jord, positiv till positiv och negativ till negativ.
Observera att jordledningen alltid skall anslutas först och kopplas bort sist.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-35
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Blank Faceplate Requirement Warning
Warning
Blank faceplates (filler panels) serve three important functions: they prevent
exposure to hazardous voltages and currents inside the chassis; they contain
electromagnetic interference (EMI) that might disrupt other equipment; and
they direct the flow of cooling air through the chassis. Do not operate the
system unless all cards, power modules, and faceplates are in place.
Waarschuwing
Lege vlakplaten (vulpanelen) vervullen drie belangrijke functies: ze
voorkomen blootstelling aan gevaarlijke voltages en elektrische stroom
binnenin het chassis; ze beperken elektromagnetische storing hetgeen
andere apparaten kan storen en ze leiden een stroom van koellucht door het
chassis. Bedien het systeem niet tenzij alle kaarten, voedingsmodules en
vlakplaten zich op hun plaats bevinden.
Varoitus
Tyhjillä kansilaatoilla (peitelevyillä) on kolme tehtävää: ne suojaavat
vaarallisilta asennuspohjan sisäisiltä jännitteiltä ja virroilta; suojaavat
sähkömagneettiselta häiriöltä (EMI), joka voi haitata muiden laitteiden
toimintaa, ja ohjaavat jäähdytysilmavirran asennuspohjan läpi. Laitetta ei saa
käyttää, jos kaikki kortit, tehomoduulit ja peitelevyt eivät ole paikoillaan.
Attention
Les caches blancs remplissent trois fonctions importantes : ils évitent tout
risque de choc électrique à l'intérieur du châssis, ils font barrage aux
interférences électromagnétiques susceptibles d'altérer le fonctionnement
des autres équipements et ils dirigent le flux d'air de refroidissement dans le
châssis. Il est vivement recommandé de vérifier que tous les caches, modules
d’alimentation et plaques de protection sont en place avant d'utiliser le
système.
Warnung
Unbeschriftete Aufspannplatten (Füllpaneelen) erfüllen drei wichtige
Funktionen : sie schützen vor gefährlichen Spannungen und Elektrizität im
Innern der Chassis; sie halten elektromagnetische Interferenzen (EMI) zurück,
die andere Geräte stören könnten; und sie lenken die Kühlluft durch das
Chassis. Nehmen Sie das System nur in Betrieb, wenn alle Karten,
Stromversorgungsmodule und Aufspannplatten an vorgesehener Stelle
odnungsgemäß installiert sind.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-36
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Avvertenza
Le piastre di protezione (pannelli di riempimento) hanno tre funzioni molto
importanti: proteggono da tensioni e correnti pericolose all’interno dello
chassis; limitano le interferenze elettromagnetiche (EMI) che possono
interferire con altre apparecchiature e dirigono il flusso d'aria di
raffreddamento attraverso lo chassis. Non usate il sistema se le schede, i
moduli di potenza, e i pannelli non sono in posizione.
Advarsel
Blanke ytterplater (deksler) har tre viktige funksjoner: De forhindrer
eksponering for farlig spenning og strøm inni kabinettet; de inneholder
elektromagnetisk interferens (EMI) som kan avbryte annet utstyr og de
dirigerer luftavkjølingsstrømmen gjennom kabinettet. Betjen ikke systemet
med mindre alle kort, drivmoduler og ytterplater sitter på plass.
Aviso
As placas em bruto (painéis de enchimento) desempenham três funções
importantes: evitam a exposição a voltagens e correntes perigosas no interior
do chassis; protegem contra interferências electromagnéticas (IEM)
passíveis de afectar outro equipamento; e orientam o fluxo do ar de
refrigeração através do chassis. Não ponha o sistema a funcionar sem que
todos os cartões, modules de potência, e placas estejam no devido lugar.
¡Advertencia!
Las placas frontales (paneles de relleno) ofrecen tres funciones importantes:
previenen la exposición a voltajes peligrosos y corrientes dentro del chasis;
contienen interferencias electromagnéticas (EMI) que pueden interrumpir
otros equipos, y dirigen el flujo de aire refrigerante a través del chasis. No
opere el sistema a menos que todas las tarjetas, módulos de potencia y placas
estén en su lugar.
Varning!
Tomma planskivor (fyllnadspaneler) fyller tre viktiga funktioner: de förhindrar
utsättning för farliga spänningar och elströmmar inuti chassit; de förhindrar
elektromagnetisk störning (EMI) som skulle kunna rubba annan utrustning;
samt de riktar flödet av kylluft genom chassit. Använd inte systemet om inte
alla kort, kraftmoduler och planskivor finns på plats.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-37
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Power Off Before Working on System Warning
Warning
Before working on a system that has a standby/off switch, turn off the power
by pressing the power switch to standby and unplug the power cord.
Waarschuwing
Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u
de voeding uit te schakelen door de voedingsschakelaar op standby te zetten
en het voedingssnoer te verwijderen.
Varoitus
Katkaise virta valmiustila/virtakytkimellä varustetusta laitteesta ennen sen
käyttämistä painamalla virtakytkin valmiusasentoon ja irrottamalla
sähköjohto.
Attention
Avant d'utiliser un système équipé d'un commutateur « Standby/Off »
(pause/arrêt), coupez l'alimentation en plaçant le commutateur sur la position
Standby et débranchez le cordon d'alimentation.
Warnung
Bevor Sie an einem System mit einem Bereit-/Aus-Schalter arbeiten, stellen
Sie den Strom ab, indem Sie den Stromschalter auf "Bereit" stellen und das
Stromkabel herausziehen.
Avvertenza
Prima di lavorare su un sistema con interruttore attesa/off, spegnetelo
premendo il pulsante sulla posizione di attesa e staccate la spina elettrica.
Advarsel
Aviso
Før det utføres arbeid på et system som har en standby/av-bryter, skal
strømmen slås av ved å skyve av/på-bryteren til standby og trekke ut
strømledningen.
Antes de começar a trabalhar num sistema com um interruptor standby
(posição de espera)/off (desligado), desligue a corrente eléctrica colocando
o interruptor na posição standby e retire o cabo de alimentação da tomada.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-38
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
¡Advertencia!
Antes de empezar a trabajar con un sistema cuyo interruptor incluya la
posición standby, cierre la corriente posicionando el interruptor a standby y
a continuación desconecte el cable eléctrico.
Varning!
Innan du arbetar på ett system med en standby-/strömbrytaromkopplare, slå av
strömmen genom att ställa omkopplaren på standby och koppla ur nätsladden.
Fan Injury Warning
Warning
Waarschuwing
The fans might still be turning when you remove the fan assembly from the
chassis. Keep fingers, screwdrivers, and other objects away from the
openings in the fan assembly’s housing.
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers en
eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.
Varoitus
Tuulettimet saattavat yhä pyöriä irrottaessasi tuuletinta asennuspohjasta.
Pidä sormet, ruuvitaltat ja muut esineet pois tuuletinkotelon aukoista.
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous
retirerez le bloc ventilateur du châssis. Prenez garde à ce que doigts,
tournevis et autres objets soient éloignés du logement du bloc ventilateur.
Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere
Gegenstände von den Öffnungen des Lüftergehäuses entfernt.
Avvertenza
Le ventole possono essere ancora in movimento quando si estrae il gruppo
ventola dallo chassis. Tenere dita, cacciavite e altri oggetti lontano dalle
aperture nell’alloggiamento del gruppo ventola.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-39
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Advarsel
Det er mulig at viftene fremdeles roterer når du tar vifteenheten ut av
chassiset. Hold fingre, skrutrekkere og andre gjenstander borte fra
vifteåpningene i viftehuset.
Aviso
Os ventiladores podem estar ainda em movimento quando retirar a unidade de
ventilação do chassis. Mantenha os dedos, chaves de parafusos e outros
objectos afastados das aberturas da caixa da unidade de ventilação.
¡Advertencia!
Los ventiladores podrían estar aún girando cuando retire el conjunto del
ventilador del chasis. Mantenga los dedos, destornilladores y otros objetos,
apartados de las aberturas de la caja del conjunto del ventilador.
Varning!
Fläktarna kanske fortfarande är igång när du tar bort fläktenheten från
chassit. Se till att du håler fingrar, skruvmejslar och andra föremål borta från
öppningarna i fläktenhetens hölje.
AC and DC Power Module Warning
Warning
Waarschuwing
Varoitus
Never install an AC power module and a DC power module in the same
chassis.
Een voedingsmodule met wisselstroom mag nooit samen met een
gelijkstroomvoedingsmodule in het chassis geïnstalleerd worden.
Älä koskaan asenna vaihtosähkötehomoduulia ja tasasähkötehomoduulia
samaan asennuspohjaan.
Attention
N’installez jamais un module d’alimentation AC et un module d’alimentation
DC dans le même châssis.
Warnung
Ein Wechelstromsmodul und ein Gleichstrommodul dürfen niemals in
demselben Chassis installiert werden.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-40
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Avvertenza
Advarsel
Non installare un modulo di alimentazione in corrente alternata e un modulo
di alimentazione in corrente continua nello stesso chassis.
En vekselstrømmodul og en likestrømmodul må aldri installeres i samme
chassis.
Aviso
Nunca instale um modulo de corrente CA (corrente alternada) e um modulo CC
(corrente contínua) no mesmo chassis.
¡Advertencia!
Nunca instale un módulo de potencia de corriente alterna (CA) en un módulo
de potencia de corriente continua (CC) en el mismo chasis.
Varning!
Installera aldrig en växelströms- och en likströmskraftenhet i samma chassi.
Power Cord Warning (other versions available)
Warning
This unit might have more than one power cord. To reduce the risk of electric
shock, disconnect the two power supply cords before servicing the unit.
Waarschuwing
Dit toestel kan meer dan één netsnoer hebben. Om het risico van een
elektrische schok te verminderen, dient u de stekkers van de twee netsnoeren
uit het stopcontact te halen voordat u het toestel een servicebeurt geeft.
Varoitus
Tässä laitteessa saattaa olla useampi kuin yksi virtajohto. Irrota molemmat
virtalähteestä tulevat johtimet ennen laitteen huoltamista, jotta vältät
sähköiskun vaaran.
Attention
Il est possible que cette unité soit munie de plusieurs cordons d'alimentation.
Pour éviter les risques d'électrocution, débrancher les deux cordons
d'alimentation avant de réparer l'unité.
Warnung
Diese Einheit hat möglicherweise mehr als ein Netzkabel. Zur Verringerung
der Stromschlaggefahr trennen Sie beide Netzgerätekabel ab, bevor Sie die
Einheit warten.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-41
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Avvertenza
Questa unità potrebbe essere dotata di più di un cavo di alimentazione. Per
ridurre il rischio di scossa elettrica, scollegare i due cavi di alimentazione
prima di procedere alla manutenzione dell’unità.
Advarsel
Denne enheten kan være utstyrt med mer enn én strømledning. Koble fra de to
strømledningene før det utføres reparasjonsarbeid på enheten for å redusere
faren for elektriske støt.
Aviso
Esta unidade poderá ter mais do que um cabo de alimentação. Para reduzir o
risco de choque eléctrico, desligue os dois cabos de alimentação antes de
efectuar reparações na unidade.
¡Advertencia!
Puede ser que este equipo posea más de un cable de alimentación. Para
reducir el riesgo de descarga eléctrica, desenchufar los dos cables antes de
proceder al mantenimiento de la unidad.
Varning!
Denna enhet kan vara försedd med mer än en nätsladd. För att minska risken
för elektriska stötar skall båda nätsladdarna dras ur innan du utför
underhållsarbete på enheten.
Ground Conductor Warning
Warning
Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable
grounding is available.
Waarschuwing
De aardingsleiding mag nooit buiten werking gesteld worden en de
apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze
geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de
bevoegde instantie voor elektrische inspecties of met een elektricien als u er
niet zeker van bent dat er voor passende aarding gezorgd is.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-42
78-13884-03
Appendix D
Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Varoitus
Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein asennettua
maajohdinta. Ota yhteyttä asianmukaiseen sähkötarkastusviranomaiseen tai
sähköasentajaan, jos olet epävarma maadoituksen sopivuudesta.
Attention
Ne jamais rendre inopérant le conducteur de masse ni utiliser l’équipement
sans un conducteur de masse adéquatement installé. En cas de doute sur la
mise à la masse appropriée disponible, s’adresser à l’organisme responsable
de la sécurité électrique ou à un électricien.
Warnung
Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne
einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich
nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie
sich an den zuständigen elektrischen Fachmann oder einen Elektriker.
Avvertenza
Advarsel
Non escludere mai il conduttore di protezione né usare l’apparecchiatura in
assenza di un conduttore di protezione installato in modo corretto. Se non si
sa con certezza che è disponibile un collegamento di messa a terra adeguato,
esaminare le Norme CEI pertinenti o rivolgersi a un elettricista qualificato.
Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert
jordingsleder. Ta kontakt med det riktige organet for elektrisk inspeksjon
eller en elektriker hvis du er usikker på om det finnes velegnet jording.
Aviso
Nunca anule o condutor à terra nem opere o equipamento sem ter um condutor
à terra adequadamente instalado. Em caso de dúvida em relação ao sistema
de ligação à terra, contacte os serviços locais de inspecção eléctrica ou um
electricista qualificado.
¡Advertencia!
No inhabilitar nunca el conductor de tierra ni hacer funcionar el equipo si no
existe un conductor de tierra instalado correctamente. Póngase en contacto
con una autoridad apropiada de inspección eléctrica o con un electricista
competente si no está seguro de que hay una conexión a tierra adecuada.
Varning!
Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på
lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida
lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker
kontaktas.
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
D-43
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch
Translated Safety Warnings
Cisco 11500 Series Content Services Switch Hardware Installation Guide
D-44
78-13884-03
I N D EX
A
C
accessory kit 1-8
cabling
AC electrical specifications 1-6, A-2
CSS 11501 2-4
AC power cord
CSS 11503 2-7
connecting CSS 11501 2-26
CSS 11506 2-7
connecting CSS 11503 2-27
Fast Ethernet Module 2-14
connecting CSS 11506 2-31
Gigabit Ethernet Module 2-16
AC power supply
LEDs C-13
troubleshooting C-11, C-12
anti-static wrist strap 1-7
application protocol A-7
audience xvii
Switch Control Module 2-11
changing the default username and
password 3-7
chassis
connecting to ground 2-22
ground connection warning 2-24
grounding lugs 2-23
preventing overheating 1-11
B
Cisco Systems
boot.log C-24
boot process
entering license key 3-5
hardware initialization 3-3
troubleshooting C-2
contacting xxiv
documentation, obtaining xxiv
configuration scripts 3-10
configuring
Ethernet Management port 3-6, B-7
Layer 3 load balancing 3-12
Layer 5 load balancing 3-14
proxy cache 3-16
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
IN-1
Index
transparent cache 3-18
connectors
DC power, checking 2-36
DC power cord
CSS 11501 2-2
connecting CSS 11503 2-28
Fast Ethernet Module 2-14
connecting CSS 11506 2-33
Gigabit Ethernet Module 2-17
DC power supply
Switch Control Module 2-11
connector location for CSS 11503 2-29
console port
connector location for CSS 11506 2-34
connector pinouts B-3
LEDs C-14
troubleshooting C-10
troubleshooting C-11, C-12
CSS 11501
disk
installing 1-12
failure C-20, C-23
mounting bracket installation 1-13
logging to C-24
overview 2-2
specifications A-5
unpacking 1-9
documentation
CSS 11503
chapter contents xviii
installing 1-14
obtaining xxiv
mounting bracket installation 1-15
related xix
overview 2-9
set xix
unpacking 1-9
symbols and conventions xxi
CSS 11506
installing 1-17
mounting bracket installation 1-18
E
overview 2-10
electrical codes (US) 1-2
unpacking 1-9
electrical specifications A-2
electro-static discharge caution 1-24
environmental specifications A-3
D
Ethernet connector, pinouts B-2
damage to product 1-10
DC electrical specifications 1-6, A-2
Ethernet Management port
configuring 3-6
Cisco 11500 Series Content Services Switch Hardware Installation Guide
IN-2
78-13884-03
Index
connector pinouts B-7
H
hardware initialization 3-3
F
fan module
I
location 2-10
installation
troubleshooting C-18
precautions 1-20
Fast Ethernet Module (FEM)
16-port LEDs and connectors 2-14
preinstallation requirements 1-11
8-port LEDs and connectors 2-14
requirements 1-11
installing
LED definitions 2-16
chassis ground connection 2-22
pinouts B-2
CSS 11501 1-12
front-mounting
CSS 11501 brackets 1-13
CSS 11503 1-14
CSS 11503 brackets 1-15
CSS 11506 1-17
CSS 11506 brackets 1-17
lifting chassis (CSS 11503 and CSS
11506) 1-3
module 1-24
G
qualified personnel (warning) 1-3
international agency compliance
information D-1
gateway protocol A-7
Gigabit Ethernet Module
cabling 2-16
L
LED definitions 2-17
LEDs and connectors 2-17
Layer 3 load balancing, configuring 3-12
grounding
Layer 5 load balancing, configuring 3-14
connecting chassis ground 2-22
CSS 1-11
lugs 2-23
wire 2-22
LEDs
CSS 11501 2-3, 2-5
Fast Ethernet Module 2-16
Gigabit Ethernet Module 2-17
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
IN-3
Index
module boot patterns 3-4
CSS 11506 1-18
power supply C-13
SCM 2-5, 2-13
Secure Socket Layer (SSL) Module 2-19
Session Accelerator Module 2-18
N
network
license key
protocol A-6
entering 3-5
utilities protocols A-7
locating 1-8, 3-5
log files
overview C-24
troubleshooting C-24
O
Offline Diagnostic Monitor Menu 3-8
logging in to the CSS 3-9
lugs, grounding 2-23
P
password-protecting the OffDM menu 3-8
M
physical specifications A-4
mid-mounting
pinouts
CSS 11503 brackets 1-15
RJ-45 fast Ethernet connector B-2
CSS 11506 brackets 1-18
RJ-45 management connector B-7
module
RJ-45 RS-232 console port B-3
installation precautions 1-20
power cords, connecting 2-26
installing 1-19, 1-24
power supply
slot restrictions 1-21
LEDs C-13
specifications A-5
troubleshooting C-11, C-12
troubleshooting C-21
preinstallation requirements 1-11
unpacking 1-24
protocols, supported A-6 to A-8
mounting brackets
proxy cache, configuring 3-16
CSS 11501 1-13
CSS 11503 1-15
Cisco 11500 Series Content Services Switch Hardware Installation Guide
IN-4
78-13884-03
Index
LED definitions 2-18
R
overview 2-18
rack-mounting
shipment contents 1-8
CSS 11503 1-15
site requirements 1-2
CSS 11506 1-19
slot restrictions 1-21
regulatory compliance D-1
software license key location 1-8
requirements
specifications
installation tools and equipment 1-7
electrical A-2
site planning 1-2
environmental A-3
RJ-45
module A-5
fast Ethernet connector pinouts B-2
modules A-5
management connector pinouts B-7
physical A-4
RS-232 console port pinouts B-3
Switch Control Module (SCM)
routing protocol A-7
connectors and LEDs 2-12
LED definitions 2-5, 2-13
passive switchover 1-26
S
sys.log C-24, C-25
syslogd, logging to C-24
safety guidelines
electricity 1-4
lifting the chassis (CSS 11503 and CSS
11506) 1-3
lightning warning 1-5
T
tools and equipment required 1-2
removing jewelry 1-5
tools and supplies, connecting chassis to
ground 2-22
US electrical codes 1-2
safety warning 1-12, 1-14, D-1
transparent cache, configuring 3-18
screws, for grounding 2-22, 2-23
transport protocol A-6
Secure Socket Layer (SSL) Module
troubleshooting
LED definitions 2-19
boot process C-2
overview 2-19
console port C-10
Session Accelerator Module (SAM)
CSS 11501 C-19
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-03
IN-5
Index
CSS 11503 fans C-16, C-17
CSS 11506 fan module C-18
modules C-21
power supply C-11, C-12
U
unpacking
CSS 11501 1-9
CSS 11503 1-9
CSS 11506 1-9
modules 1-24
V
VTY log files C-24, C-25
W
warning, safety 1-12, 1-14
wire stripping tool 2-22
wiring
chassis ground 2-22
safety (warning) 1-7
Cisco 11500 Series Content Services Switch Hardware Installation Guide
IN-6
78-13884-03