36"UnderCabinetHood
UXT3036AY
KeyFeatures
• Vented Under Cabinet Hood
(New Design)
• Axial Fan
• Covered, Incandescent Light (75-Watt)
• 2-Speed, Rocker Switch Control
• Washable, Grease Filter
• Vertically Exhausts up to 190 CFM with a
3 1/4" x 10" Rectangular Duct
36" Under Cabinet Hood
UXT3036AY
Specifications
Location Requirements
Installation Clearances
Installation
Requirements
IMPORTANT: Observe all governing codes and ordinances.
model no.
■ It is the installer’s responsibility
to comply uxt3036ay
with installation
Vented
Type
clearances specified
on
the
model/serial
rating
plate. The
Location Requirements
model/serial
rating
plate
is
located
inside
the
range
hood on
duct
type
IMPORTANT: Observe all governing codes and ordinances.
the left wall. Rectangular 3 1/4" x 10"
Yes
■ It is the installer’s responsibility to comply with installation
■ Range
hoodspecified
location
should
be
away fromrating
strong
draftThe
areas,
Washable
Filter
Yes
clearances
onGrease
the model/serial
plate.
such
as windows,
and
strong
heating
vents.
model/serial
ratingdoors
plate
is
located
inside
the
range
hood
on
vertical cfm
the left wall.
■ Cabinet
opening
dimensions
that are shown must
3 1/4"
x 10" Rectangular
182 be used.
provide
minimum
Consult
the
■ Given
Rangedimensions
hood location
should
be
awayclearance.
from strong
draft areas,
horizontal
cfm
cooktop/range
manufacturer
installation
instructions
before
such as windows,
doors3and
191
1/4" xstrong
10" heating vents.
making any cutouts.
■ Cabinet opening dimensions
that are shown must be used.
vertical Sones
■ Grounded
electrical
outlet
is
required.clearance.
See “Electrical
Given dimensions
minimum
Consult the
5.8
3 1/4" provide
x 10"
Rectangular
Requirements”
section.
cooktop/range
manufacturer
installation
instructions
before
general information
making
any cutouts.
■ All
openings
in ceiling
and
wall
where
range
hood
will
be
5.3
Horizontal Sones
must
be sealed.
■ installed
Grounded
electrical
outlet is
required.
See
“Electrical
Control
2-Speed, Rocker Switch
Requirements”
section.
■ These
range Adapter/Vent
hoods
are factory
set for vented
installations.
Included
Connector
that are
capable
of wall
being
installed
ashood
non-vented
■ Models
All openings
in ceiling
and
where
range
will be
Blower
Axial Fan
(recirculating)
charcoal filters. See the “Accessories”
installed mustrequire
be sealed.
1 Level, Incandescent
section to order charcoal filter
kit.
Lighting
(75-Watt)
■ These range hoods are factory set for vented
installations.
Models
that
are
capable
of
being
installed
as
non-vented
Title
24
Compliant
Yes
For Mobile Home Installations
(recirculating)
require charcoal
filters. SeeUp
theto“Accessories”
Range/Cooktop
Compatibility
The installation of this range hood must conform to40K
theBTU
section to order charcoal filter kit.
Manufactured
Home
Construction
Safety Standards,
Approx.
Shipping
Weight (lbs.)
13 Title 24
CFR, Part 328 (formerly
the
Federal Standard for Mobile Home
optional
accessories
For Mobile Home
Installations
Construction
and Safety,
title 24, HUD, Part 280) or when such
Power
Cord
W10355452
The installation
of this range
hood
must conform
to the Home
standard
is not applicable,
the
standard
for Manufactured
Manufactured
Home
Construction
Safety
Standards,
Title 24
3 1/4"1982
x 10"
Rectangular
Damper
Kit Sites,
W10398259
Installation
(Manufactured
Home
Communities
and
CFR,
Part
328
(formerly
the
Federal
Standard
for
Mobile
Home
Setups) ANSI A225.1/NFPA
501A*, or latest edition, or with
local
Color Availability
W,B
Construction and Safety, title 24, HUD, Part 280) or when such
codes.
Note: CFMs are based on IEC standard
* W-White, B-Black
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Product
Dimensions
Setups)
ANSI
A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product ⁷⁄₈"
Dimensions
Dimensions
(2.2 cm)
4¹⁵⁄₁₆"
(12.5 cm)
4¹⁵⁄₁₆"
(12.5 cm)
6⁹⁄₁₆" (16.7 cm)
6⁹⁄₁₆" (16.7 cm)
⁷⁄₈"
(2.2 cm)
⁷⁄₈"
(2.2 cm)
⁷⁄₈"
29¹⁵⁄₁₆" (76.0 cm) or
(2.2 cm)
35¹⁵⁄₁₆" (91.0 cm)
29¹⁵⁄₁₆" (76.0 cm) or
35¹⁵⁄₁₆" (91.0 cm)
1"
(2.5 cm)
1"
9" (2.5 cm)
(22.9 cm)
2¹⁄₈"
(5.4 cm) 18⁵⁄₈"
(47.39"
cm)
(22.9 cm)
2¹⁄₈"
(5.4 cm) 18⁵⁄₈"
(47.3 cm)
Installation Clearances
C
B
C
B
D
A
D
A
E
E
A. 18" (45.7 cm) min. clearance - upper cabinet to countertop
B. 18" (45.7 cm) to 24" (61.0 cm) suggested max. - bottom of range
hood to cooking surface
C. 30" (76.2 cm) min. cabinet opening width for 30" (76.2 cm)
and
36"
(91.4
cm) min.
cabinet
width to
forcountertop
36" (91.4 cm)
A. models
18" (45.7
cm)
min.
clearance
- upper
cabinet
B. models.
18" (45.7 cm) to 24" (61.0 cm) suggested max. - bottom of range
D. 13"
(33.0
cm) cabinet
depth
hood
to cooking
surface
E. 36"
cabinet opening
height width for 30" (76.2 cm)
C.
30" (91.4
(76.2 cm) base
min. cabinet
models and 36" (91.4 cm) min. cabinet width for 36" (91.4 cm)
models.
D. 13" (33.0
cm)
cabinetpurposes
depth only.
Dimensions
are for
planning
E. 36" (91.4
cm) see
baseInstallation
cabinet height
For complete
details,
Instructions packed with product.
Venting Requirements
Vent system must terminate to the outdoors, except for nonSpecifications subject to change without notice.
vented (recirculating) installations.
■
■
■
■
■
■
■
■
■
■
®Registered trademark/™ Trademark of Whirlpool, U.S.A. ©2011. All rights reserved.
Venting
Do not terminate
the ventRequirements
system in an attic or other enclosed
area.
Vent system must terminate to the outdoors, except for nonvented
(recirculating)
Do
not use
a 4" (10.2 installations.
cm) laundry-type wall cap.
Do
not
terminate
the
vent
system
in an
or xother
enclosed
Use a 7" (17.8 cm) round metal
vent
or attic
a 3¹⁄₄"
10" (8.3
x
area.
25.4 cm) rectangular metal vent, depending on your model.
Rigid
metal
is recommended.
Plastic
orcap.
metal foil vent is
Do not
use avent
4" (10.2
cm) laundry-type
wall
not recommended.
Use a 7" (17.8 cm) round metal vent or a 3¹⁄₄" x 10" (8.3 x
The
of vent system
number
of elbows
should
be
25.4length
cm) rectangular
metaland
vent,
depending
on your
model.
kept
a minimum
to provide efficient
performance.
Rigidto
metal
vent is recommended.
Plastic
or metal foil vent is
not recommended.
The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
AA105059