SyncMaster 150MP / 170MP
User's Manual - 2
Index
Main Page
Safety Instructions
Notational
Adjusting Your LCD Monitor
User Controls
Power
User control buttons
Installation
Direct-Access Features
Cleaning
On -Screen Display
OSD Functions
Other
Screen Adjustment Animation Clips
Introduction
Unpacking
Troubleshooting
Front
Check before Calling for Service
Rear
Problems and Solutions
Remote Control
Q&A
Specifications
Setup
Connecting Your Monitor
General Specifications
Connecting to a Computer
PowerSaver
Connecting to Other Devices
Preset Timing Modes
Installing the Monitor Driver
Information
Automatic
Service Center
Manual
Terms
Base Installation
Regulatory
Using the FOLD button
Natural Color
Installing a VESA Base
Authority
User's Manual - 3
Safety Instructions-Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
User's Manual - 4
Safety Instructions-Power
When not used for extended periods of time, set your PC to DPMS. If using a
screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
l
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
l
This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
l
An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects upon
them, which could cause damage.
l
This may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is
not used for a long period of time.
l
Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
l
This may cause a fire.
User's Manual - 5
Safety Instructions-Installation
Do not cover the vents on the monitor cabinet.
l
Bad ventilation may cause a breakdown or fire.
Put your monitor in a location with low humidity and a minimum of dust.
l
An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
l
This may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
l
The monitor can cause injury by falling.
Set down the monitor carefully.
l
It could be damaged or broken.
Do not place the monitor face down.
l
The TFT-LCD surface may be damaged.
User's Manual - 6
Safety Instructions-Cleaning
When cleaning the monitor case or the surface of the TFT -LCD, wipe with a slightly
moistened, soft fabric.
Do not spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it
properly with a dry cloth.
l
A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects on the
monitor.
l
l
This may cause damage, electric shock or a fire.
If a foreign substance gets into the monitor, disconnect the plug and then
contact a service center .
User's Manual - 7
Safety Instructions-Other
Do not remove cover(or back). No user serviceable parts inside.
l
l
This may cause an electric shock or a fire.
Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any
unusual sounds or smells coming from it - unplug it immediately and
contact an authorized dealer or service.
l
This may cause an electric shock or fire.
Do not place any heavy objects on the monitor.
l
This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let your eyes rest for
5 minutes.
l
This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
l
This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal cable.
l
This may cause a breakdown, electric shock or a fire due to damage to
the cable.
Do not move the monitor right or left by pulling only the wire or the signal
cable.
l
This may cause a breakdown, electric shock or a fire due to damage to
the cable.
User's Manual - 8
Safety Instructions-Other
Never insert anything metallic into the monitor openings.
l
This may cause an electric shock, fire or injury.
User's Manual - 9
Introduction-Unpacking
Please make sure the following items are included with your monitor. If any items are missing, contact
your dealer .
User's Guide and Natural
Color/Driver Installation CD
Power Cord
Signal Cable(15 pin D-Sub)
DC Adapter
Remote Control / Batteries (AAA X 2)
Quick Setup Guide
Monitor
Audio Cable
Warranty Card
(Not available in all locations)
User's Manual - 10
Introduction-Front
For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your
Monitor. The monitor's front configuration may vary slightly depending on the monitor model.
1 Input Signal Indicators
5 Menu button
2 Source button
6 Power button / Power indicator
3 PIP button
7 Up-Down button / Channel button
4 Exit button / Auto button
8 Left-Right button / Volume button
PIP(Picture in Picture)?
Feature allowing one program to be viewed on the entire screen
while one or more programs play in small windows superimposed
over the base program. PIP is also referred to as Split Windows.
User's Manual - 11
Introduction-Rear
For detailed information concerning cable connections, refer to Connecting Cables under Setup.
The monitor's rear configuration may vary slightly depending on the monitor model.
Remove the cover to connect the cables. (Pull the joining part to remove the cover.)
A
Power Connection Terminal (14V DC)
This product may be used with 90 ~ 264. (Voltage
is automatically adjusted by the power adaptor.)
Connect the power source plug when all cables are
connected.
B
Video Connection Terminal
1
PC connection terminal (15 pin D -SUB)
2
S-Video(V1) connection terminal (S -VHS)
3
Video(V2) connection terminal (RCA)
C
Audio Connection Terminal
1
Left audio(L) connection terminal (Input)
2
Right audio(R) connection terminal (Input)
3
PC sound(Stereo) connection terminal (Input)
4
Headphone connection terminal (Output)
D
Antenna Connection Terminal (When TV is
connected)
E
Anti-Theft Security Lock
User's Manual - 12
Introduction-Remote Control
For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User
Controls > User Control Buttons > Remote Control buttons .
The remote control's configuration may vary slightly depending on the monitor model.
The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the
left and right of the monitor's Remote Control Reception sensor.
Button Names | Replacing Batteries
1. Button Names
1 Power button
2 PC button
3 PIP(Picture -in-Picture) button
4 Video button
5 Audio button
6 PIP Position button
7 PIP Size button
8 Up-Down button / Channel button
9 Left -Right button / Volume button
10 Menu button
11 Mute button
12 Exit button
13 Channel button
14 Display button
15 Previous channel button
16 Auto button
17 Channel search button
18 MTS/S -mode button
19 Caption button
User's Manual - 13
Introduction-Remote Control
2. Replacing Batteries
1. Slide out the cover pressing part marked .
2. Insert the batteries matching their polarities (+, -).
3. Slide in the cover.
User's Manual - 14
Setup-Connecting to a Computer
Turn on your computer and monitor. If your monitor displays an image, installation is complete.
1. Connecting to a Computer
1. Connect the power cord to the DC adapter and connect the adapter jack to the DC14V power port
on the back of your monitor.
2. Connect the signal cable to the video port on your computer.
3. Connect the audio cable for your monitor to the audio port on the back of your computer.
4. Connect the Audio (L) and Audio (R) terminals of a DVD, VCR or Camcorders to the monitor's L
and R audio input terminals using audio cables.
5. Turn on both your computer and the monitor.
6. You may enjoy clear and quality sound from the computer sound card using the monitor speakers.
(You don't need to install any separate speakers for your computer.)
Contact a local Samsung Electronics service center to buy optional items.
User's Manual - 15
Setup-Connecting to Other Devices
AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the
monitor. For detailed information on connecting AV input devices, refer to User Controls under
Adjusting Your Monitor.
Connecting AV Devices | Connecting TV | Connecting to a Macintosh | Connecting Headphones
1. Connecting AV Devices
The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or
Camcorders. You may enjoy AV signals as long as the monitor is turned on.
1. AV input devices like DVDs, VCRs or Camcorders are connected to the S -Video (V1) or Video (V2)
terminal of the monitor using the S-VHS or RCA cable.
S -VHS or RCA cable is optional.
2. Connect the Audio (L) and Audio (R) terminals of a DVD, VCR or Camcorder to the monitor's L and
R audio input terminals using audio cables.
3. Select Video or S-Video that is connected to a DVD, VCR or Camcorder using the Source button on
the monitor's front.
4. Then, start the DVD, VCR or Camcorder with a DVD disc or tape inserted.
User's Manual - 16
Setup-Connecting to Other Devices
2. Connecting TV
You may view television programs on the monitor if it is connected to an antenna or CATV cable
without installing any separate TV reception hardware or software on your computer.
1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor.
You need to use a coaxial antenna cable.
2. Turn on the monitor.
3. Select TV using Source button among the external signal adjustment buttons.
4. Select a desired TV channel.
As this product is designed for NTSC signals only, you cannot view TV programs in countries
where PAL or SECAM signals are used.
3. Connecting to a Macintosh
User's Manual - 17
Setup-Connecting to Other Devices
1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC14V power
port on the monitor. (Voltage is automatically adjusted by the power adaptor.)
2. Connect the signal cable to the D-SUB port on the Macintosh computer.
3. For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh
adapter (optional) referring to the switch configuration table shown on its rear.
4. Turn on the monitor and Macintosh.
Contact a local Samsung Electronics service center to buy optional items.
4. Connecting Headphones
You may connect your headphones to the monitor.
1. Connect your headphones to the Headphone -out port.
User's Manual - 18
Setup-Installing the Monitor Driver (Automatic)
When prompted by the operating system for the monitor driver, insert the CD -ROM included with
this monitor. Driver installation is slightly different from one operating system to another. Follow
the directions as appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
l
Internet web site : http://www.samsung -monitor.com/ (Worldwide)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Windows ME | Windows XP/2000
1. Windows ME
Refer to "Installing the Monitor Driver and User Manual " CD-ROM supplied with the monitor.
When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up
automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer.
1. Insert CD into the CD-ROM driver.
2. Click " Windows ME Driver "
3. Choose your monitor model in the model list, then click the " OK " button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.
User's Manual - 19
Setup-Installing the Monitor Driver (Automatic)
2. Windows XP/2000
Refer to "Installing the Monitor Driver and User Manual " CD-ROM supplied with the monitor.
When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up
automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer.
1. Insert CD into the CD-ROM driver.
2. Click " Windows XP/2000 Driver ".
3. Choose your monitor model in the model list, then click the " OK " button.
4. Click the "Install" button in the "Warning" window.
5. If you can see following Message window, then click the "Continue Anyway " button. Then click "OK "
button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.
The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/
6. Monitor driver installation is completed.
User's Manual - 20
Setup-Installing the Monitor Driver (Manual)
When prompted by the operating system for the monitor driver, insert the CD -ROM included with
this monitor. Driver installation is slightly different from one operating system to another. Follow
the directions as appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
l
Internet web site : http://www.samsung -monitor.com/ (Worldwide)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
To install the monitor driver manually, follow the procedures explained below after checking your
operating system.
Windows XP | Windows 2000 | Windows Me | Windows NT | Linux
1. Microsoft® Windows ® XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click " Start" — > " Control Panel" then click the " Appearance and Themes " Icon.
3. Click " Display" icon and choose the "Settings" tab then click " Advanced..".
4. Click the "Properties" button on the "Monitor " tab and select "Driver " tab.
User's Manual - 21
Setup-Installing the Monitor Driver (Manual)
5. Click " Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click " Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list
and click the "Next" button.
User's Manual - 22
Setup-Installing the Monitor Driver (Manual)
8. If you can see following "Message " window, then click the " Continue Anyway " button. Then click
"OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.
The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/
9. Click the "Close" button then click "OK " button continually.
User's Manual - 23
Setup-Installing the Monitor Driver (Manual)
10. Monitor driver installation is completed.
2. Microsoft® Windows ® 2000 Operating System
* When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK " button on the " Insert disk" window.
2. Click the "Browse" button on the " File Needed" window.
3. Choose A:(D:\Driver) then click the " Open" button and then click "OK " button.
* How to install
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Click " Start" , "Setting" , "Control Panel ".
Double click the " Display" Icon.
Choose the " Settings" tab and then click " Advanced..".
Choose "Monitor ".
Case 1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation.
Case 2: If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
Click " Driver" and then click on " Update Driver.." then click on the "Next" button.
Choose "Display a list of the known drivers for this device so that I can choose a specific
driver" then click "Next" and then click " Have disk".
Click the "Browse" button then choose A:(D:\Driver).
Click the "Open" button, then click " OK " button.
Choose your monitor model and click the "Next" button then click " Next" button.
Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button. And
click the "Finish" button then the "Close" button.
3. Microsoft® Windows® Millennium Operating System
1.
2.
3.
4.
5.
6.
7.
8.
9.
Click " Start" , "Setting" , "Control Panel ".
Double click "Display " icon.
Select the "Settings" tab and click " Advanced Properties" button.
Select the "Monitor " tab.
Click the "Change" button in the "Monitor Type " area.
Choose "Specify the location of the driver".
Choose "Display a list of all the driver in a specific location.. " then click "Next" button.
Click the "Have Disk" button
Specify A:\(D:\driver) then click " OK " button.
User's Manual - 24
Setup-Installing the Monitor Driver (Manual)
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK ".
11. Continue choosing "Close" button and " OK " button until you close the Display Properties dialogue
box.
(You can get some other screen for warning message or others, then click the appreciate option for
your monitor.)
4. Microsoft® Windows® NT 4.0 Operating System
1. Click Start, Settings, Control Panel, and then double -click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then
click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not
normal, change to a different mode (lower mode of resolution, colors or frequency).
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by
referring to the Preset Display Modes in the user guide.
5. Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Press Enter at the first and the second screen after executing the X86Config file.
The third screen is for setting your mouse.
Set a mouse for your computer.
The next screen is for selecting a keyboard.
Set a Keyboard for your computer.
The next screen is for setting your monitor .
First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
Set a vertical frequency for your monitor. (You can enter the frequency directly.)
Enter the model name of your monitor. This information will not affect the actual execution of X Window.
10. You have finished setting up your monitor.
Execute X -Window after setting other requested hardware.
User's Manual - 25
Setup-Using the FOLD button
The monitor may be reclined from 0 to 90 degrees. When fully folded (reclined), the base becomes a
handy holder for moving the monitor around.
Reclining the Monitor | Folding Base
1. Reclining Monitor
1. The monitor may be reclined by approximately 15 degrees without pressing the FOLD button.
2. You need to press the FOLD button to raising the monitor over 15 degrees.
Pull the Rear Supporter for safety when reclining the monitor backward from 90 degrees.
User's Manual - 26
Setup-Using the FOLD button
2. Folding Base
1. Disconnect the monitor cables.
2. Fully recline the monitor backward pressing the FOLD button.
3. Reconnect the monitor cables.
You may install a VESA base when the monitor base is fully folded.
User's Manual - 27
Setup-Installing a VESA Base
The monitor supports VESA mounting standard for use with various VESA mounting devices.
This monitor accepts a 75mm x 75mm (100mm x 100mm: 17 inch) VESA-compliant mounting
interface pad. You need to fold the monitor base before installing a VESA base.
Align the four bolt holes (1) on the monitor base with the holes (2) on the VESA base and then fasten
the base with the four bolts (3) supplied.
Only the supplied bolts should be used.
Samsung Electronics will not be responsible for damages caused by using a base other than those
specified.
User's Manual - 28
Adujust Monitor-User control buttons
The control button configuration may vary slightly depending on the monitor model.
Monitor Buttons | Remote Control Buttons
1. Monitor Buttons
For more information about screen adjustment, refer to On -Screen Display .
1. Input Signal Indicators
If the Source or PIP button is pressed, the corresponding indicator turns on to indicate the input signal
currently displayed on the screen. When PIP button is pressed, two signal indicators turn on: (Indicator
color: Green)
2. Source button
Turns on the indicator to indicate the currently displayed input signal.
To switch Screen modes: PC --> Video --> S-Video --> TV (Press here to view Screen Mode Switching
Animation Clips)
3. PIP button
In PC Mode, turns on Video or TV screens in PIP mode. Using this function, you may view a Video or
TV program while performing PC work. To deactivate PIP mode, press the Exit button. (Exit button
works in PC mode only.)
To switch Screen modes: PC + Video -- > PC + S-Video --> PC + TV (Press here to view Screen Mode
Switching Animation Clips)
4. Exit button / Auto button
When screen adjustment menu is on: Exit button exits from the menu screen or closes screen
adjustment menu. Also turns off PIP screens when pressed in PIP mode.
When screen adjustment menu is off: Auto button adjusts the screen automatically. For more
information, refer to Direct -Access Features > Automatic Save.
5. Menu(
) button
Use this button to open the OSD and activate a highlighted menu item.
6. Power button / Power indicator
Use this button to turn the monitor on and off. Power Indicator shows PowerSaver mode by green
blinking. Refer to Specifications > PowerSaver.
User's Manual - 29
Adujust Monitor-User control buttons
7.
- CH +
button
Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects
TV channels. For more information, refer to Direct-Access Features > Channel.
8.
- VOL +
button
Moves from one menu item to another horizontally or adjusts selected menu values. Also adjusts the
audio volume. For more information, refer to Direct-Access Features > Volume.
Remote Control Buttons
For more information on the screen adjustment functions, refer to On-Screen Display.
1 Power button
2 PC button
3 PIP(Picture -in-Picture) button
4 Video button
5 Audio button
6 PIP Position button
7 PIP Size button (Supports only 17" monitors)
8 Up-Down button / Channel button
9 Left -Right button / Volume button
10 Menu button
11 Mute button
12 Exit button
13 Channel button
14 Display button
15 Previous channel button
16 Auto button
17 Channel search button
18 MTS/S -mode button
19 Caption button
1. Power button
Use this button to turn the monitor on and off.
2 PC button
Switches from Video screen mode to PC screen mode.
3 PIP(Picture -in-Picture) button
User's Manual - 30
Adujust Monitor-User control buttons
In PC Mode, turns on Video or TV screens in PIP mode. Using this function, you may view a
Video or TV program while performing PC work. To deactivate the PIP screen, press the Exit
button. (Exit button works in PC mode only.)
4 Video button
Switches from PC screen mode to Video screen mode.
5 Audio button
Adjusts Audio mode. You may switch to the Audio signal for the current display mode when the
wrong audio is playing.
6 PIP Position button
Adjusts the location of Video image in PIP mode. Press
the location up and down or left and right.
- CH +
,
- VOL +
buttons to adjust
7 PIP Size button
Allows the user to turn off or adjust the size of the PIP screen.
8 Up-Down button / Channel button
Moves from one menu item to another vertically or adjusts the selected menu value. In TV mode,
selects TV channels. For more information, refer to Direct-Access Features > Channel.
9 Left -Right button / Volume button
Moves from one menu item to another horizontally or adjusts selected menu values. Also adjusts
the audio volume. For more information, refer to Direct -Access Features > Volume.
10 Menu(
) button
Use this button to open the OSD and activate a highlighted menu item.
11 Mute button
Pauses (mutes) the audio output temporarily. The audio resumes if Mute or
pressed in the Mute mode.
- VOL +
button is
12 Exit button
Exits from or closes the menu screen. Also turns off the PIP screen when pressed in PIP mode.
13 Channel button
Selects TV channels in the TV mode. You may use this button in PIP mode as well.
14 Display button
Shows a Video Source, Audio Source, current channel number, an audio type and Speaker Mute
ON/OFF on the upper right corner of the screen.
15 Previous channel button
This button is used to return to the immediately previous channel.
16 Auto button
User's Manual - 31
Adujust Monitor-User control buttons
Adjusts the screen display automatically. For more information, refer to Direct-Access Features >
Automatic Save.
17 Channel search button
Automatically scans and registers TV channels available (viewable) in the current location. For
detailed information on adjusting the TV screen, refer to OSD Functions > TV Screen .
18 MTS/S -mode button
When you press this button, current audio mode is displayed on the lower left corner of the
screen.(Only TV Screen)
FM Stereo
Audio Type
MTS/S_Mode
Mono
Mono
Stereo
Mono < --> Stereo
SAP
Mono < --> SAP
Default
Automatic Change
Mono
19 Caption button
Turns on Closed Captioning service (in English). In some countries, Caption service is not
available. You may turn on Closed Captioning service while viewing certain television programs in
countries like the United States or a video tape with a "CC" marking.
User's Manual - 32
Adujust Monitor-Direct-Access Features
Direct-Access Features let you display Monitor Adjustment Menu by simply pressing Auto button once.
Or they are used to adjust monitor functions. You need to activate functions other than Auto Adjustment
only when Auto-Access Features are off.
Automatic Save | OSD Lock/Unlock | Volume | Channel
1. Automatic Save
The monitor display becomes more stabilized if adjusted by Auto
Adjustment functions when the monitor is installed for the first time. Try
Auto Adjustment before attempting Manual Adjustment. Ensure the clock
frequency of the monitor matches that of the computer video card before
carrying out Auto Adjustment.
When the Auto button is pressed, the monitor screen turns black and the
Auto Adjustment screen appears as shown in the animated screen on the
left.
To make the automatic adjustment function sharper, execute the 'AUTO' function while the
AutoPattern.exe is on.
2. OSD Lock/Unlock
This function allows you to secure the current settings so that they cannot be
inadvertently changed.
With the OSD screen off, push and hold the Menu button for at least 5
seconds to lock or unlock the controls.
The following functions are available even while the OSD menu is locked.
1. Control buttons
2. PC Screen
3. TV Screen
Source button, PIP button, Volume button, Channel
button, Menu button, Exit button, Auto button
Brightness, Contrast
Channel, Volume
With the OSD screen off, push and hold the Menu button for five or more seconds to unlock the OSD
settings.
3. Volume
When OSD is not on the screen, push the
1. Push the
2. Push the
or
button to decrease the volume.
button to increase the volume.
button to adjust volume.
User's Manual - 33
Adujust Monitor-Direct-Access Features
4. Channel
When OSD is not on the screen, push the
number.
1. Push the
2. Push the
or
button to select channel
button to decrease the channel number.
button to increase the channel number.
This function is available in TV or PC + TV (PIP) mode only.
User's Manual - 34
Adujust Monitor-On-Screen Display
Characters and icons become highlighted in blue during adjustment for each menu.
PC Screen | Video Screen | TV Screen | OSD Control
1. PC Screen
For detailed information on Screen Adjustment in the PC mode, refer to PC Screen Adjustment
Animation Clips.
Contrast
Adjust Contrast.
Brightness
Adjust Brightness.
Color Control
The tone of color can be changed from redish white to bluish white. The individual color
components are also user customizable.
1) Mode 1: Plain white.
2) Mode 2: Reddish white.
3) Mode 3: Bluish white.
4) User Mode: User customizable.
5) Reset: Color parameters are replaced with the factory default values.
Image
This menu includes Image Lock and Image Effect as its sub-menu.
1) Image Lock:
Image Lock is used to fine tune and get the best image by removing noises that creates unstable
images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment,
use the Coarse adjustment and then use Fine again.
• Coarse:
• Fine:
• Information:
• Reset:
Removes noise such as vertical stripes. Coarse adjustment may move the
screen image area. You may relocate it to the center using the Horizontal
Control menu.
Removes noise such as horizontal stripes. If the noise persists even after Fine
tuning, repeat it after adjusting the frequency (clock speed).
Display current display mode.
Image lock and position parameters are replaced with the factory default
values.
2) Image Effect:
Image being displayed can be made softer or sharper.
Position
This adjusts the screen location horizontally and vertically.
Sound
The monitor has a built-in high fidelity stereo audio amplifier.
1) Bass: Emphasize low frequency audio.
2) Treble: Emphasize high frequency audio.
3) Audio Source: Selects a sound source from PC, TV, DVD or VCR.
User's Manual - 35
Adujust Monitor-On-Screen Display
PIP
When external A/V devices such as VCR or DVD are connected to the monitor, PIP allows you to
watch video from such devices in a small window super-imposed on pc video signal.
1) PIP Off / On: Turns the PIP mode on or off. (SyncMaster 150MP)
Size: Allows the user to turn off or adjust the size of the PIP screen. (SyncMaster 170MP)
2) Position: Change PIP window position.
2. Video Screen
For detailed information on Screen Adjustment in the Video mode, refer to Video Screen Adjustment
Animation Clips. Screen Adjustment in the Video mode does not affect the PC screen at all.
Picture
Controls Video screen properties such as Contrast, Brightness, Sharpness, Color and Tint.
1)
2)
3)
4)
5)
6)
Contrast : Adjust the contrast of video without affecting PC RGB's contrast.
Brightness: Adjust the brightness of video without affecting PC RGB's brightness.
Sharpness: Adjust the sharpness of video image.
Color: Change the richness of color.
Tint: Change the tone of color.
Reset: Picture parameters are replaced with the factory default values.
Sound
The monitor has a built-in high fidelity stereo audio amplifier.
1) Bass : Emphasize low frequency audio.
2) Treble: Emphasize high frequency audio.
3) Audio Source : Selects a sound source from PC, TV, DVD or VCR.
Closed Caption
Enable or disable closed caption feature and set the appearance of closed caption text.
V - Chip
Protects children from viewing inappropriate programs by blocking certain broadcast or video
programs.
3. TV Screen
For detailed information on Screen Adjustment in TV mode, refer to TV Screen Adjustment
Animation Clips. Screen Adjustment in TV mode does not affect the PC screen at all.
User's Manual - 36
Adujust Monitor-On-Screen Display
Setup
The channel system can be set in several different ways.
1) Channel System:
Select a channel system that is being used in your region.
• US-Air
• US-Cable
• Japan-Air
• Japan-Cable
Upon selecting a channel system, you will be asked if you want to perform "Channel Search". Select
"Yes" to perform the "Channel Search" or select "No" to select different channel system.
For detailed instructions, refer to "1. Setup (TV Setup) > 1) Channel System" in TV Screen
Adjustment Animation Clips.
2) Channel Edit:
Adds or erases channels from the memory.
In rare cases, "Channel auto program" may miss a couple of channels due to weak signals or for
other reasons such as a channel does not exist when "Channel auto program" is executed.
3) Fine Tune:
Due to weak signals or a wrong antenna configuration, some of the channels may not be tuned
correctly.
4) Stereo System :
Due to the various encoding schemes, the audio system corresponding to the channel system must
be selected manually. Currently, there are three stereo audio systems in NTSC system: A2(Korea),
BTSC(U.S.) and EIAJ (Japan).
5) LNA :
Amplifies signals when antenna reception is poor. However if incoming signals are interfering with
each other, turn off LNA as it may malfuction.
For explanations on the TV control menu, refer to the explanations under Video Screen. You may
control TV Screen properties in the same way as for Video Screen .
4. OSD Control
For detailed information on screen adjustment functions, refer to OSD Screen Adjustment Animation
Clips.
Language
User's Manual - 37
Adujust Monitor-On-Screen Display
You can choose one of 4 languages. (English, French, Spanish, Portuguese)
Note: The language chosen affects only the language of the OSD. It has no effect on any software
running on the computer.
Position
Move the OSD Window to the vertical and horizontal direction.
HalfTone
Change the opaqueness of the background of the OSD.
Duration
The number of seconds that the OSD will remain visible before disappearing.
Color
Changes the color of the OSD menu screen background.
User's Manual - 38
Troubleshooting-Check before Calling for Service
Check the following items yourself before calling for service. Contact the service center for problems
that you cannot solve by yourself.
Self-Test Feature Check | Video mode not supported | Display Adapter Driver | For Better Display |
Dot Acceptable | Maintenance and Cleaning | Symptoms & Recommended Actions
1. Self-Test Feature Check
Your monitor provides a self test feature that allows you to check whether your monitor is functioning
properly.
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
The figure shown below ("Check Signal Cable") appears on a black background when the monitor is
in its normal working condition though it does not sense any video signal: While in the Self-Test
mode, the LED power indicator remains green and the figure moves around on the screen.
Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears
during normal operation if the video cable becomes disconnected or damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller and
computer system; your monitor is functioning properly.
2. Video mode not supported
This indicates the display resolution or refresh rate is not properly set on your computer video card. Reboot
the computer in Safe Mode and select "Default" in the "Refresh Rate Unknown" box while setting Adapter
for Display Properties.
Contact the computer dealer or manufacturer for information on Safe Mode Booting.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are supported
by the monitor.
The screen sometimes remains black even though it does not show the message "Video mode not
supported." This indicates the monitor is set for a frequency out of range or the PowerSaver mode is on.
3. Display Adapter Driver
Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot
User's Manual - 39
Troubleshooting-Check before Calling for Service
adjust resolution, frequency or color and you cannot install the monitor driver.
1. Checking Adapter Driver
Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced -- > Adapter.
If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly
installed. Install the adapter driver again according to the information provided by the computer or
video card manufacturers.
2. Installing Adapter Driver
The instructions given below are for general circumstances. For specific issues, contact the
relevant computer or video card manufacturers.
1) Click Start -- > Settings --> Control Panel --> Display --> Settings --> Advanced --> Adapter -->
Update Driver --> Next --> Display a list of the known drivers for this device so that I can
choose a specific driver -- > Next -> Have Disk (Insert Video Card Driver diskette) -> OK -> Next
-> Next -> Finish.
2) In case you have Adapter Driver Setup file on your computer:
Run Setup.exe or Install.exe, which is found in the Adapter Driver Setup file.
4. For Better Display
1. Selecting Resolution and Color
If the monitor resolution or color is not properly set, the screen may show blurred images or mosaic
patterns.
Procedures for setting frequency in the Control Panel may vary depending on the video card.
Setting Color & Resolution >>
Click Start --> Settings --> Control Panel --> Display --> Settings --> Colors & Screen area -->
Apply --> OK.
You
size
• 15
• 17
can get the best image quality by selecting resolution depending on the monitor screen
as follows:
inch monitor : 1024 x 768 @60Hz
inch monitor : 1280 x 1024 @60Hz
Select 16 or 24 bit color.
• Supported or not subject to the video card (the monitor is irrelevant)
• LCD monitors may display up to 16.77 million colors (24 bits).
2. Setting Refresh Rate
If the monitor refresh rate is not properly set, the screen image may be skewed or noise patterns will
appear. You can enjoy the best screen image when the refresh rate is set to 60 Hz.
Setting Refresh Rate >>
Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced -- > Refresh Rate -- >
Apply -- > Yes -- > OK --> Yes.
3. If the screen image is not acceptable or satisfactory, run AUTO ADJUSTMENT, to get a better
image quality, in the screen that appears immediately after you click Windows System End button. If
the noise persists even after AUTO ADJUSTMENT, adjust the screen settings using FINE/COARSE
tuning buttons.
5. Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999%
above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright
User's Manual - 40
Troubleshooting-Check before Calling for Service
sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without
uneasiness.
l 15 inch: 2,359,296
The number of TFT LCD pixels :
l 17 inch: 3,932,160
l 18 inch: 3,932,160
l 21 inch: 5,760,000
l 24 inch: 6,912,000
6. Maintenance and Cleaning
1. Maintaining the Monitor Case
Clean with a soft cloth after disconnecting the power cord.
l
l
Do not use benzene, thinner or other flammable substances, or a
wet cloth.
We recommend a Samsung cleansing agent is used to prevent
damage to the screen.
2. Maintaining the Flat Panel Display Screen
Clean with a soft cloth (cotton flannel) smoothly.
l
l
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
The user will be required to pay costs and related expenses for
repair of damages caused by him/her.
7. Symptoms and Recommended Actions
1.
2.
3.
4.
5.
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the
video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not
supported, etc. In this case, first check the source of the problem, and then contact a service center or
your dealer.
Check if the power cord and the cable are properly connected to the computer.
Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
Check if the scanning ratio of the video screen is set at 75Hz.
(Do not exceed 60Hz when using the maximum resolution.)
If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the "Control Panel, System, Device Administrator" and then
reboot the computer to reinstall the adapter (video) driver.
User's Manual - 41
Troubleshooting-Problems and Solutions
The following table lists possible problems and their solutions. Before calling for service, check the
information in this section to see if you can remedy any problems yourself. If you do need assistance,
please call the phone number on the warranty card, the phone number on the Information section or
contact your dealer.
Installation | Screen | Audio | Remote Control
1. Problems related to Installation
Problems related to the monitor installation and their solutions are listed.
Problems
Solutions
It appears the PC does not
function normally.
l
Check if the Display Adapter Driver (VGA Driver) is properly
installed. (Refer to Installing Driver)
The monitor screen flickers.
l
Check if the signal cable between the computer and the
monitor is securely connected and tightened. (Refer to
Connecting to a Computer )
TV screen is blurred or shows
noise signals.
l
Check if the TV antenna connector is securely connected to
the external antenna. (Refer to Connecting to TV)
TV signal is not received
l
Check "Channel system" and make sure you choose the
correct channel system. (Refer to the Channel System)
Select "Channel auto program" to configure the channel
system automatically. (Refer to the Channel System)
l
Strange characters appear on the
screen.
l
Switch "Caption On" to "Caption Off" if strange characters
appear on the TV screen. (Refer to Closed Caption)
2. Problems related to Screen
Problems related to the monitor screen and their solutions are listed.
Problems
Solutions
Screen is blank and power
indicator is off
l
Ensure that the power cord is firmly connected and the LCD
monitor is on. (Refer to the Connecting Your Monitor)
"Check Signal Cable" message
l
Ensure that the signal cable is firmly connected to the PC or
video sources. (Refer to the Connecting Your Monitor)
Ensure that the PC or video sources are turned on.
l
"Video mode not supported"
message
l
l
Check the maximum resolution and the frequency of the
video adaptor.
Compare these values with the data in the Preset Timing
Modes Chart.
User's Manual - 42
Troubleshooting-Problems and Solutions
Picture rolls vertically.
l
Check if the signal cable is securely connected. Connect it
again securely.(Refer to Connecting to a Computer)
Image is not clear. Picture is
blurred.
l
Run Frequency Coarse and Fine tuning.
Turn on again after removing all accessories (video
extension cable, etc.)
Set resolution and frequency to the recommended ranges.
15 inch model (1024 x 768 @ 60Hz), 17 inch model (1280 x
1024 @ 60Hz)
l
l
Picture image is unstable and
vibrates.
l
Check if the resolution and frequency set for the computer
video card falls in the range supported by the monitor. If not,
reset them referring to the current Display Mode under the
monitor menu and Preset Timing Modes.
The image is too light or too dark
l
Adjust the Brightness and Contrast.
(Refer to the Brightness , Contrast)
Screen color is inconsistent.
l
Adjust color using User Mode under OSD Color Adjustment
menu.
Power Indicator blinks green.
l
The monitor is currently saving the changes made in settings
to the OSD memory.
Screen is blank and power
indicator light is steady green or
blinks every 0.5 or 1 seconds
l
The monitor is using its power management system.
Move the computer's mouse or press a key on the keyboard
The monitor front control buttons
do not respond.
l
Ghost images are shown in the
picture.
Color image is distorted with
dark shadows.
White color is poor.
l
l
Check if OSD Lock/Unlock is on by pressing Menu button.
If the problem persists, contact the service center.
3. Problems related to Audio
Problems related to audio signals and their solutions are listed below.
Problems
No sound
Solutions
l
l
Sound level is too low.
l
l
Ensure that the audio cable is firmly connected to both the
audio-in port on your monitor and the audio -out port on your
sound card. (Refer to the Connecting Your Monitor)
Check the volume level. (Refer to the Volume)
Check the volume level. (Refer to the Volume)
If the volume is still too low after turning the control to its
maximum, check the volume control on the computer sound
card or software program.
User's Manual - 43
Troubleshooting-Problems and Solutions
Sound is too high pitched or too
low pitched
l
Adjust the Treble and Bass to appropriate level.
4. Problems related to Remote Control
Problems related to the remote control and their solutions are listed.
Problems
The remote control buttons do
not respond.
Items to check
l
l
l
l
l
Check the battery polarities (+/-).
Check if the batteries have been exhausted.
Check if the power is on.
Check if the power cord is securely connected.
Check if a special fluorescent or neon lamp is on in the
vicinity.
User's Manual - 45
Troubleshooting-Q & A
Frequently asked questions are summarized here for your reference.
Question
How can I change the frequency?
Answer
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the
version of the driver used. (Refer to the computer or the video
card manual for details.)
How can I adjust the resolution?
Windows XP:
Reset resolution by clicking Control Panel --> Appearance &
Theme --> Display -- > Settings.
Windows ME/2000:
Set the resolution at the Control Panel -- > Display --> Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows XP:
Reset Power Saving parameters by clicking Control Panel -->
Appearance & Theme --> Display -- > Screen Saver or in the
computer BIOS SETUP. (Refer to Windows/Computer Manual)
Windows ME/2000:
Set the function at BIOS -SETUP of the computer or the screen
saver. (Refer to Windows/Computer Manual).
How can I clean the outer case/LCD
Panel?
Disconnect the power cord and then clean the monitor with a
soft cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the
case. Do not allow any water to go inside the monitor.
User's Manual - 45
Specifications-General
Design and specifications are subject to change without prior notice.
General
Model Name
SyncMaster 150MP
LCD Panel
Size
15.0 inch (Diagonal)
Display area
304.1 (H) x 228.1 (V)
Pixel Pitch
0.297 (H) x 0.297 (V)
Type
a-si TFT active matrix
Viewing Angle
70/70/60/60 (L/R/T/B)
Synchronization
Horizontal
30 ~ 61 kHz
Vertical
56 ~ 75 Hz
Display Color
16,777,216 Colors
Resolution
Optimum resolution
1024 x 768@60Hz
Maximum resolution
1024 x 768@75Hz
Input Signal
Separate: TTL, P. or N.
Sync.
Composite: TTL, P. or N.
Video signal
0.7 Vp-p @ 75 ohm
TV / Video
Color system
NTSC
Sound system
M/N
Video format
CVBS, S-VHS
Maximum Pixel Clock
80 MHz
Power Supply
AC 110 ~ 220 V (60/50 Hz), DC 14V/3.0A
Power Consumption
42W (Maximum)
Power Saving
Less than 2W
Dimensions (WxDxH)
User's Manual - 46
Specifications-General
Monitor body
382 x 57 x 380 mm
With stand
382 x 188 x 380 mm
Weight
Monitor body
4.5 kg
Carton
7.0 kg
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50 °F ~ 104°F(10°C ~ 40°C)
Humidity : 10% ~ 80%, non-condensing
Storage
Temperature : -13 °F ~113 °F (-25 °C ~ 45 °C)
Humidity : 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation
will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999%
above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright
sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without
uneasiness.
The number of TFT LCD pixels :
l
l
l
l
l
15
17
18
21
24
inch:
inch:
inch:
inch:
inch:
2,359,296
3,932,160
3,932,160
5,760,000
6,912,000
User's Manual - 47
Specifications-General
Design and specifications are subject to change without prior notice.
General
Model Name
SyncMaster 170MP
LCD Panel
Size
17.0 inch (Diagonal)
Display area
338 (H) x 270 (V)
Pixel Pitch
0.264 (H) x 0.264 (V)
Type
a-si TFT active matrix
Viewing Angle
80/80/60/60 (L/R/T/B)
Synchronization
Horizontal
30 ~ 80 kHz
Vertical
56 ~ 75 Hz
Display Color
16,777,216 Colors
Resolution
Optimum resolution
1280 x 1024@60Hz
Maximum resolution
1280 x 1024@76Hz
Input Signal
Separate: TTL, P. or N.
Sync.
Composite: TTL, P. or N.
Video signal
0.7 Vp-p @ 75 ohm
TV / Video
Color system
NTSC
Sound system
M/N
Video format
CVBS, S-VHS
Maximum Pixel Clock
80 MHz
Power Supply
AC 110 ~ 220 V (60/50 Hz), DC 14V/3.5A
Power Consumption
52W (Maximum)
Power Saving
Less than 2W
Dimensions (WxDxH)
User's Manual - 48
Specifications-General
Monitor body
448 x 63 x 438 mm
With stand
448 x 207 x 438 mm
Weight
Monitor body
6.5 kg
Carton
9.5 kg
VESA Mounting Interface
100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50 °F ~ 104°F(10°C ~ 40°C)
Humidity : 10% ~ 80%, non-condensing
Storage
Temperature : -13 °F ~113 °F (-25 °C ~ 45 °C)
Humidity : 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation
will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999%
above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright
sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without
uneasiness.
The number of TFT LCD pixels :
l
l
l
l
l
15
17
18
21
24
inch:
inch:
inch:
inch:
inch:
2,359,296
3,932,160
3,932,160
5,760,000
6,912,000
User's Manual - 49
Specifications-PowerSaver
This monitor has a built -in power management system called PowerSaver. This system saves energy
by switching your monitor into a low-power mode when it has not been used for a certain amount of
time. The monitor automatically returns to normal operation when you move the computer's mouse or
press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS
compliant video card installed in your computer. Use a software utility installed on your computer to set
up this feature.
SyncMaster 150MP
State
Normal Operation
Power saving mode
EPA/ENERGY 2000
Power Switch off
Power Indicator
Green
Green, Blinking
Black
Power Consumption
Less than 42W
Less than 2W
Less than 1W
State
Normal Operation
Power saving mode
EPA/ENERGY 2000
Power Switch off
Power Indicator
Green
Green, Blinking
Black
Power Consumption
Less than 52W
Less than 2W
Less than 1W
SyncMaster 170MP
This monitor is EPA E NERGY S TAR ® compliant and ENERGY2000 compliant when
used with a computer equipped with VESA DPMS functionality.
As an E NERGY S TAR ® Partner, SAMSUNG has determined that this product meets the
ENERGY S TAR ® guidelines for energy efficiency.
User's Manual - 50
Specifications-Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the
power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
SyncMaster 150MP
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VGA, 720 x 400
31.469
70.087
28.322
-/+
VGA, 640 x 480
31.469
59.940
25.175
-/-
VGA, 640 x 480
37.500
75.000
31.500
-/-
SVGA, 800 x 600
46.875
75.000
49.500
+/+
XGA, 1024 x 768
48.363
60.004
65.000
-/-
XGA, 1024 x 768
60.023
75.029
78.750
+/+
Pixel Clock
(MHz)
Sync Polarity
(H/V)
SyncMaster 170MP
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
VGA, 720 x 400
31.469
70.087
28.322
-/+
VGA, 640 x 480
31.469
59.940
25.175
-/-
VGA, 640 x 480
37.500
75.000
31.500
-/-
SVGA, 800 x 600
46.875
75.000
49.500
+/+
XGA, 1024 x 768
48.363
60.004
65.000
-/-
XGA, 1024 x 768
60.023
75.029
78.750
+/+
SXGA, 1280 x 1024
63.981
60.020
108.000
+,-/+,-
SXGA, 1280 x 1024
79.976
75.025
135.000
+/+
User's Manual - 51
Specifications-Preset Timing Modes
Table 2. NTSC Broadcasting Systems
Color System
NTSC
Sound System
M
Stereo System
Channel System
Countries
A2
US
Korea
BTSC (SAP)
US
USA, Canada,
Chile, Venezuela,
Cuba, Colombia,
Jamaica, Mexico,
Panama, Peru,
Philippines, PuertoRico, Taiwan
EIAJ
Japan
Japan
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of the
Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called Vertical Frequency or Refresh Rate. Unit: Hz
User's Manual - 52
Information-Service Center
U.S.A. :
Samsung Computer Products Customer Service
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856
Tel. : (973)601-6000, 1-800-SAMSUNG (1 -800-726-7864)
Fax. : (973)601-6001
http://www.samsungusa.com/monitor/
BRAZIL :
Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719 -040
Sao Paulo, SP
SAC : 0800 124 421
http://www.samsung.com.br/
CANADA :
Samsung Electronics Canada Inc.
7037 Financial Drive
Mississauga, Ontario L5N 6R3
Tel. : 1-800-SAMSUNG (1 -800-726-7864)
Fax. : (905) 542-1199
http://www.samsung.ca/
COLOMBIA :
Samsung Electronics Colombia
Cra 9 No 99A -02 Of. 106
Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 - 2068
http://www.samsung-latin.com/
e-mail : soporte@samsung-latin.com
PANAMA :
Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
http://www.samsung-latin.com/
PERU
Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
http://www.samsungperu.com/
GERMANY :
TELEPLAN Rhein -Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732 * EURO 0.12/MIN.
http://www.samsung.de/
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
http://www.samsung.com.au/
User's Manual - 53
Information-Service Center
ITALY :
Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153
http://www.samsung-italia.com/
ESPA Ñ A :
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
http://samsung.es/
United Kingdom :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
http://samsungservice.co.uk/
THAILAND :
HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
SOUTH AFRICA :
Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11 -549-1621
Fax : 0027-11-549-1629
http://www.samsung.co.za/
UKRAINE :
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
http://www.samsung.com.ua/
SWEDEN/DENMARK/NORWAY/FINLAND :
Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄ SBY
SVERIGE
Besöksadress : Johanneslundsv ä gen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
User's Manual - 54
Information-Service Center
Fax +46 8 590 966 50
http://www.samsung.se/
HUNGARY :
Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
http://www.samsung.hu/
FRANCE :
SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
http://www.samsungservices.com/
PORTUGAL :
SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua M ário Dioniso, N o2 - 1° Drt. 2795 -140 LINDA -A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128
Free Line 800 220 120
http://www.samsung.pt/
NETHERLANDS/BELGIUM/LUXEMBOURG :
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800 -2295214, http://www.samsung.nl/
CHILE :
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
http://www.sonda.com/
http://www.samsung.cl/
MEXICO :
Samsung Electronics Mexico S.A. de C.V.
Saturno 44 Col. Nueva Industrial Vallejo
Del. Gustavo A. Madero C.P. 07700
Mexico D.F.
Tel. 01 57 47 51 00
Fax. 01 57 47 52 02
RFC: SEM950215S98
http://www.samsung.com.mx/
IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO S.A. DE C.V.
SATURNO 44 COL. NVA. INDUSTRIAL VALLEJO
DEL. GUSTAVO A. MADERO C.P. 07700
MEXICO D.F. TEL. 5747-5100
RFC: SEM950215S98
EXPORTADO POR: SAMSUNG ELECTRONICS CO.,LTD.
JOONG -ANG DAILY NEWS BLDG.
7 SOON -WHA-DONG CHUNG-KU,
C.P.O BOX 2775, 1144 SEOUL, KOREA
User's Manual - 55
Information-Terms
Sync Signal
Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on
the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal
color images by the set resolution and frequency.
Types of Sync Signals
Separate
This is a scheme of transmitting individual vertical sync signals to the monitor.
Composite
This is a scheme of combining vertical sync signals into one composite signal
and transmitting it to the monitor. The monitor displays the color signals by
separating the composite signal into original color signals.
Sync On Green
This scheme does not use sync signals. Instead, it combines horizontal and
vertical sync signals into a Green signal and transmits to the monitor. It is mainly
used for workstations.
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the
resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the
user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this case,
flickering of the screen can be detected. To avoid this problem, there is a Flicker-free Mode
using a vertical frequency over 70 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called
Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the Non-Interlace
method while showing odd lines and then even lines in turn is called the Interlace method. The NonInterlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the
same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the
monitor to exchange information automatically. This monitor follows the international standard VESA DDC
for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This
number shows the accuracy of the display. High resolution is good for performing multiple tasks as more
image information can be shown on the screen.
Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal dots
(horizontal resolution) and 768 vertical lines (vertical resolution).
A2
This system uses two carriers to transmit voice data. Countries such as South Korea and Germany use
this system.
BTSC
Broadcast Television System Committee
The stereo broadcasting system that is used in most of the countries that have adopted the NTSC
system, including the United States, Canada, Chile, Venezuela and Taiwan. It also refers to the
organization that has been organized to promote its development and management.
EIAJ
Electronic Industries Association of Japan
User's Manual - 56
Information-Regulatory
FCC Information | IC Compliance Notice | MPR II Compliance |
European Notice (Europe only) | PCT Notice | VCCI |
TCO'95-Ecological requirements for personal computers (TCO applied model only)
TCO'99-Ecological requirements for personal computers (TCO applied model only)
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the
following warning:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television receptions, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment. If necessary, consult your dealer or an experienced
radio/television technician for additional suggestions. You may find the booklet called How to Identify
and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal
Communications Commission. It is available from the U.S. Government Printing Office, Washington,
DC 20402, Stock Number 004-000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Tel) 949-975-7310
Fax) 949-922-8301
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may
be suitable for connection to any UL Listed personal computer with similar configuration. Before
making the connection, make sure the voltage rating of the computer convenience outlet is the same
as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds
the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P
type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power
supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.
IC Compliance Notice
User's Manual - 57
Information-Regulatory
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations of ICES -003.
Cet appareil Numé rique de classe B respecte toutes les exigences du R èglemont NMB-03 sur les
é quipements produisant des interf é rences au Canada.
MPR II Compliance
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
European Notice (Europe only)
Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and
the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
z EN55022:1998+A1:2000 - Radio Frequency Interference
z EN55024:1998 - Electromagnetic Immunity
z EN55013:1990+A12:1994+A13:1996+A14:1999 - Radio Frequency Interference
z EN55020:1994+A11:1996+A12/A13/A14:1999 - Electromagnetic Immunity
z EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics
z EN61000-3-3:1995 - Voltage Fluctuations
z EN60065:1997 or EN60095:1998 - Product Safety
PCT Notice
VCCI
This is a Class B product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment according to the instruction
manual.
User's Manual - 58
Information-Regulatory
TCO'95-Ecological requirements for personal computers (TCO applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed to reducing
the burden on the environment and to the further development of environmentally-adapted electronic
products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment.The main problem as far as monitors and other
electronic equipment are concerned is that environmentally harmful substances are used both in the
products and during their manufacture. Since it has not been possible so far for the majority of electronic
equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or
later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are important
from both the working and natural environment viewpoints. Since all types of conventional electricity
generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive
waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of
energy, since it is often routinely left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international
environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The
Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for
Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in
Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical
and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product
must be prepared for recycling and the manufacturer is obliged to have an environmental plan, which must
be adhered to in each country where the company conducts its operations policy. The energy requirements
include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a
lower level, in one or more stages. The length of time to reactivate the monitor shall be reasonable for the
user.
Labelled products must meet strict environmental demands, for example in respect of the reduction of
electric and magnetic fields, along with physical and visual ergonomics and good usability.
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by this product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
User's Manual - 59
Information-Regulatory
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO'95-approved and labelled products may also
be obtained via the Internet, using the address:
http://www.tco-info.com/
TCO'95 is a co-operative project between(3 logos)
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In
turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of
flame retardant substances. These are related to another group of environmental toxins, PCBs, which are
suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals,
due to the bioaccumulative processes. Flame retardants have been found in human blood and researchers
fear that disturbances in foetus development may occur.
z TCO'95 demand requires that plastic components weighing more than 25 grams must not contain
organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning.
z
TCO'95 requirement Permits the inclusion of lead since no replacement has yet been developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses.
z TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
cadmium. The colour-generating layers of display screens must not contain any cadmium.
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is
toxic in high doses.
z TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
mercury. It also demands that no mercury is present in any of the electrical or electronics components
concerned with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of
expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of
skin cancer (malignant melanoma).
z The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the manufacturing of
the product or its packaging.
User's Manual - 60
Information-Regulatory
TCO'99-Ecological requirements for personal computers (TCO applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a
product developed for professional use. Your purchase has also contributed to reducing the burden on the
environment and also to the further development of environmentally adapted electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international
environmental and quality labelling labelling of personal computers. The labelling scheme was developed
as a joint effort by the TCO(The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens Energimyndighet(The
Swedish National Energy Administration) and SEMKO AB.
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of electric
and magnetic fields, energy consumption and electrical safety.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and other
electronics equipment are concerned, is that environmentally harmful substances are used both in the
products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of
electronics equipment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing
emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running
continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish
Society for Nature Conservation). These demands impose restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs(freons)and chlorinated solvents, among other
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental policy which must be adhered to in each country where the company implements its
operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
User's Manual - 61
Information-Regulatory
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labelled products may also be obtained via the
Internet, using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose
is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can
consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame
retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants
containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including
reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame
retardants have been found in human blood and researchers fear that disturbances in foetus development
may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the
printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99
requirement states that batteries, the colour-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic
in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light
system of flat panel monitors as today there is no commercially available alternative. TCO aims on
removing this exception when a Mercury free alternative is available.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit
boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing
increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant
melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion
of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
User's Manual - 62
Information-Narueal Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer or
other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed
by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute
(ETRI). This system is available only for Samsung monitors and makes the color of the images on the
monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD -ROM Drive. Then, the initial screen of the
program installation will be executed. Click Natural Color on the initial screen to install the Natural Color
software. To install the program manually, insert the CD included with the Samsung monitor into the CD ROM Drive, click the [Start] button of Windows and then select [Execute].
Enter D:\color\eng\setup.exe and then press the <Entrer> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select [Setting]/[Control Panel] on the [Start] menu and then double -click [Add/Delete a program].
Select Natural Color from the list and then click the [Add/Delete] button.
User's Manual - 63
Information-Authority
Information in this document is subject to change without notice.
© 2003 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is
strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows
NT are registered trademarks of Microsoft Corporation; VESA , DPMS and DDC are registered trademarks of
Video Electronics Standard Association; the E NERGY S TAR name and logo are registered trademarks of the
U.S. Environmental Protection Agency (EPA). As an ENERGY S TAR Partner, Samsung Electronics Co., Ltd.
has determined that this product meets the ENERGY S TAR guidelines for energy efficiency. All other product
names mentioned herein may be the trademarks or registered trademarks of their respective owners.
http://www.samsung-monitor.com/ (Worldwide)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/ (China)