Central Pneumatic 95826 Operating instructions

POWDER COATING SYSTEM
94244
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
3491 MISSION OAKS BLVD., CAMARILLO, CA 93011
VISIT OUR WEB SITE AT HTTP://WWW.HARBORFREIGHT.COM
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
SPECIFICATIONS
Ite m
P o w e r C o n s u m p tio n
L in e C o rd
A ir S u p p ly P re s s u re
C u b ic F e e t P e r
M in u te
A ir In le t S iz e
R e m o te A c tiv a tio n
S w itc h
G un Pow der Lead
G ro u n d in g C a b le
C o n tro l B o x F u s e
P a in t C u rin g
T e m p e ra tu re
W e ig h t
D e s c rip tio n
120 VAC , 60 H z
6 fe e t lo n g , 1 6 A W G , 3 -p ro n g g ro u n d e d p lu g
1 0 to 3 0 P S I
3 .5 C F M a t 3 0 P S I
¼ in c h
1 0 fe e t lo n g
8 fe e t, h ig h v o lta g e le a d .
8 fe e t lo n g w ith g ro u n d c la m p
0 .5 a m p s
4 0 0 d e g re e s F . fo r 1 5 m in u te s (re c o m m e n d e d )
6 .3 5 lb s .
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions
listed below may result in electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTION
Work Area
1.
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite
the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
4.
Use tool in a well ventilated area. Spray dust can cause injury or explosion hazard.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 2
Electrical Safety
5.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
6.
Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
7.
Grounded tools must be plugged into an outlet properly installed and grounded
in accordance with all codes and ordinances. Never remove the grounding
prong or modify the plug in any way. Do not use any adapter plugs. Check with
a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. If the tools should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
8.
Double insulated tools are equipped with a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet. Do not change the plug in any
way. Double insulation
eliminates the need for the three wire grounded power
cord and grounded power supply system.
9.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools or
pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp
edges, or moving parts. Replace damaged Power Cords immediately. Damaged
Power Cords increase the risk of electric shock.
10.
When operating a power tool outside, use an outdoor extension cord marked
“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk
of electric shock.
Personal Safety
11.
Stay alert. Watch what you are doing, and use common sense when operating a
power tool. Do not use a power tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating power tools may
result in serious personal injury.
12.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
13.
Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Carrying power tools with your finger on the Power Switch, or plugging in power tools
with the Power Switch on, invites accidents.
14.
Remove adjusting keys or wrenches before turning the power tool on. A wrench
or a key that is left attached to a rotating part of the power tool may result in personal
injury.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 3
15.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
16.
Use safety equipment. Always wear eye, face, and breathing protection. Dust
mask, non-skid safety shoes, hard hat, or hearing protection must be used for
appropriate conditions.
Tool Use and Care
17.
Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
18.
Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
19.
Do not use the power tool if the Power Switch does not turn it on or off. Any tool
that cannot be controlled with the Power Switch is dangerous and must be replaced.
20.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
21.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
22.
Maintain tools with care. Properly maintained tools are less likely to clog and are
easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
23.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
24.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous when
used on another tool.
Service
25.
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
26.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions may
create a risk of electric shock or injury.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 4
SPECIFIC SAFETY RULES FOR THIS PRODUCT
1.
Maintain labels and nameplates on the Powder Coating System. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
2.
Always wear ANSI approved safety impact eye goggles, respirator, and heavy
work gloves when using the Powder Coating System. Using personal safety
devices reduce the risk for injury. Safety impact eye goggles and heavy work gloves
are available from Harbor Freight Tools.
3.
Maintain a safe working environment. Keep the work area well lit. Make sure there
is adequate surrounding workspace. Always keep the work area free of obstructions,
grease, oil, trash, and other debris. Do not use a power tool in areas near flammable
chemicals, dusts, and vapors. Do not use this product in a damp or wet location.
4.
Avoid unintentional starting. Make sure you are prepared to begin work before
turning on the Powder Coating System.
5.
Do not force the Powder Coating System. This tool will do the work better and safer
at the speed and capacity for which it was designed.
6.
Always unplug the Powder Coating System from its electrical outlet before
performing any inspection, maintenance, or cleaning procedures.
7.
Never leave the Powder Coating System unattended while running. Turn power
off if you have to leave the Powder Coating System.
8.
Before each use, check all nuts, bolts, and screws for tightness. Vibration during
mixing may cause these to loosen.
9.
Keep extension cord off the ground and away from water.
10.
Always connect the Power Cord to a grounded electrical outlet.
11.
The powder dust is flammable when floating in the air.
- Ventilate the area well.
- Verify that there are no flames or ignition source nearby.
- Control excess dust by cleaning up after each use.
- Never vacuum up the dust using a non-explosion proof vacuum cleaner.
- Never cure coated object in a gas oven as the fumes recreated can be flammable;
(1)
only use an electric oven.
- Never smoke while using the Powder Coating System.
12.
Avoid electrical shock!
- Never touch the emitter (metal tip) of the Spray Gun. After use (and turned OFF),
touch the emitter to the Ground Clip to discharge it.
- Do not use the Spray Gun if you carry and use any electronic medical devices.
- Never touch the metal object during coating.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 5
13.
Avoid powder contamination.
- Protect your lungs by using an approved dust mask.
- Never cure objects in an electric oven that is used for food also.
- Ventilate the area well.
- Wear an activated charcoal respirator when oven curing the coated object.
14.
People with pacemakers should consult their physician(s) before using this
product. Electromagnetic fields in close proximity to a heart pacemaker could cause
interference to or failure of the pacemaker.
WARNING!
This product contains or, when used, produces a chemical known to the State of
California to cause cancer and birth defects or other reproductive harm.
(California Health & Safety Code § 25249.5, et seq.)
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool or
product. Never remove the grounding prong from the plug. Do not use the tool if
the power cord or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper outlet installed
by a qualified electrician.
Grounded Tools with Three Prong Plugs
The Powder Coating System comes with a 3-prong grounded plug.
1.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If the tool
should electrically malfunction or break down, grounding provides a low resistance
path to carry electricity away from the user, reducing the risk of electric shock. (See
Figure A on the next page.)
2.
The grounding prong in the plug is connected through the green wire inside the cord
to the grounding system in the tool. The green wire in the cord must be the only wire
connected to the tool’s grounding system and must never be attached to an
electrically “live” terminal. (See Figure A.)
SKU 94244
For technical questions, please call 1-800-444-3353
Page 6
3.
Your tool must be plugged into an appropriate outlet, properly installed and grounded
in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (See Figure A.)
Figure A
Figure B
Double Insulated Tools with Two Prong Plugs
4.
Tools with a polarized plug (one blade is wider than the other) serve as a feature to
reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Never use with an extension cord unless plug can be fully
inserted. Do not alter the plug.”
5.
Tools marked “Double Insulated” do not require grounding. They have a special double
insulation system which satisfies OSHA requirements and complies with the
applicable standards of Underwriters Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code. (See Figure B above.)
6.
Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B above.)
EXTENSION CORDS
1.
Grounded tools require a three wire extension cord. Double Insulated tools can use
either a two or three wire extension cord.
2.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a serious
drop in voltage, resulting in loss of power and possible tool damage. (See Table A.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See
Table A.)
4.
When using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required. (See Table A.)
5.
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size. (See Table
A.)
6.
If you are using an extension cord outdoors, make sure it is marked with the suffix “WA” (“W” in Canada) to indicate it is acceptable for outdoor use.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 7
7.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified electrician
before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet
areas.
Table A
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
NAMEPLATE
AMPERES
(At Full Load)
EXTENSION CORD LENGTH
25
50
75
100
150
Feet
Feet
Feet
Feet
Feet
0 – 2.0
18
18
18
18
16
2.1 – 3.4
18
18
18
16
14
3.5 – 5.0
18
18
16
14
12
5.1 – 7.0
18
16
14
12
12
7.1 – 12.0
16
14
12
10
12.1 – 16.0
14
12
10
16.1 – 20.0
12
10
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
SYMBOLOGY
Table B
UNPACKING
When unpacking, check to make sure the following parts are included (Refer to the Parts
List and Assembly Drawing at the end of this manual and the photo on the next page.):
If any parts are missing or broken, please call Harbor Freight Tools at the number on the
cover of this manual as soon as possible.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 8
Three Scatter Tips (21, 22, 24)
Spray Gun (2)
Two Powder Cups (4)
Control Box (11)
Power Cord (19)
Pressure Reducer Valve (8)
Disposable Moisture
Separator (9)
Quick Adapter (10)
Foot Switch (16)
Ground Wire (26)
and Clip (15)
PREPARATION
1.
Setup an air supply with an air pressure regulator and moisture trap (do not use an inline air oiler). The air compressor must provide an air pressure of 10 to 30 PSI.
2.
Select a safe location for spraying and curing with:
- adequate lighting
- active ventilation
- no flame or ignition source
- an area dry, clean, and covered – free of flammable material
3.
Have an activated charcoal filter respirator availability for use when curing.
4.
Have disposable dust masks available for use when powder spraying.
5.
Have a pair of vinyl gloves for use when handling the power and sprayed objects.
6.
Use ANSI approved eye safety glasses.
7.
If using an extension cord, it must have a ground prong.
8.
Setup a dedicated electric oven (not included), with adequate ventilation, for curing
the coated objects with a temperature capability from 300 to 500 degrees F.
WARNING: Never use a gas oven, the fumes from curing can be explosive. Never use a
home oven that is also used for food. Contamination of food will occur.
9.
Clean the object to be powder coated of any old coatings, rust, grease and oil.
OPERATION
(1)
1.
Place or hang the cleaned object to be coated near the ventilation system.
If the object has grooves or recesses, position the object so that gravity assists the
powder mist to fall into the grooves or recesses.
2.
Connect the Disposable Moisture Separator (9) to the Spray Gun (2).
SKU 94244
For technical questions, please call 1-800-444-3353
Page 9
3.
Unscrew the Powder Cup (4) from the Spray Gun (2) and fill with up to two inches of
coating powder (not supplied). See photo below, left.
a. Turn the Cup open side up, and place on a clean piece of paper.
b. Put on a pair of disposal vinyl gloves.
c. Open the powder coating container, and using a funnel as a guide, pour the
powder into the Powder Cup.
d. Turn the Spray Gun upside down and screw the Cup back into the Spray Gun.
e. Reseal powder container.
Scatter Tip (21, 22, or 24)
Regulating Screw (7)
Quick Adapter (10)
Conductor Pole (25)
Trigger (6)
1/4” Air Hose
Disposable Moisture
Separator (9)
Pressure Reducer
Valve (8)
Powder Cup (4)
4.
Attach the Quick Adapter (10) to the Disposable Moisture Separator (9).
5.
Connect a 1/4 inch air hose (not supplied) to the Quick Adapter (10).
6.
Screw in the desired Scatter Tip (21, 22, or 24) to the Conductor Pole (25).
7.
Attach the Ground Clip (15) to the metal object being coated.
Securely attach the Ground Clip to an area which is not being coated. This connection
is absolutely necessary to draw the electrically charged (power) particles to the metal
object.
Power Switch (14)
Place Foot Switch (16) on
the floor near the workpiece
Ground Clip to Workpiece
High Voltage Wire (27) to
Spray Gun (2)
8.
Press the Control Box Power Switch (14) to the ON (I) position.
9.
Turn on the compressor and adjust its air pressure regulator to between 10 and 30
PSI pressure. Minor pressure changes can be made with the Pressure Reducer Valve
(8) during operation.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 10
10.
Press the Spray Gun Trigger (6) and Foot Switch (16) at the same time and test the
spray pattern on a piece of scrap metal.
The Trigger controls the air and powder flow. The Foot Switch controls the electrical
charge. If the pattern is too small or too large, change the Scatter Tip size (Read step
11 first).
Remember that the pointed end of the Scatter Tip faces toward the Spray
Gun and screws on. The spray pattern can also be adjusted using the
Regulating Screw (7): loosen to expand the pattern, tighten to reduce the
pattern size.
11.
When coating, keep the Spray Gun approximately eight inches from the
metal workpiece.
Point the Spray Gun toward the object at different angles to guarantee that all areas
are coated. When completed, the object should be completely coated with a dull,
opaque coat of powder.
12.
When you are finished spraying:
a. Remove your foot from the Foot Switch (16),
b. Press the Control Box Power Switch (14) to the OFF (O) position,
c. Unplug the Power Cord (19) from the electrical outlet.
WARNING: The Spray Gun is still electrically charged. Discharge Conductor Pole (25) tip
to ground before touching or you could be shocked.
13.
Touch the Conductor Pole (25) to the Ground Clip (15) to discharge any residual
electricity.
14.
Wipe the Scatter Tip off with a clean cloth.
15.
Place the activated charcoal respirator over your face, mouth, and hose.
WARNING: The fumes produced during curing are hazardous to your health. Do not
breath. Always use a NIOSH (National Institute for Occupational Safety and Health) approved respirator and safety goggles. Avoid skin exposure. Proper ventilation in the
work area is required.
16.
With the oven preheated to the desired temperature (300 to 500 degrees F), place the
object on the oven rack, close the door, and turn the ventilation system on.
- Typical curing time is 15 minutes. Check the Powder Coating container for
recommended curing time and temperature.
- If the object is large, curing may take more time.
- The power coating should melt to a smooth, gloss finish all over the object.
- Check the curing object often to prevent over-curing which can cause roughness to
the surface.
17.
When cured, turn the oven off and open the oven door slightly to allow the object to
cool gradually before removing. When the object is cooled too rapidly, a dull finish
may result.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 11
Process Tips
1.
To remove an orange peel effect after curing, wet-sand the object with 400 grit
sandpaper, dry, and repeat the coating process. Over-powder coating can cause this
effect.
2.
Polish with traditional paint polishes.
3.
Lightly buff with a loose wheel and white rouge compound to remove imperfections.
4.
Thoroughly clean the Powder Cup (4) before changing powders.
Some powders are made from polyester, while others are made from polyurethane. A
mixture of both can cause pitting of the coated object.
5.
Porous metal objects may need a thorough cleaning with a brush and pre-painting
cleaning solutions.
6.
If the powder starts to buildup in one place, blow off with light air pressure. Moisture in
the air will cause powder buildup. Replace the Disposable Moisture Separator (9).
7.
Poor disbursement can be caused by low air pressure. Adjust the air pressure or
replace the Disposable Moisture Separator. The Cup should have at least one inch of
powder during coating.
8.
Use automotive paint remover to remove a cured coating.
MAINTENANCE
Cleaning the Powder Coating System
1.
Wear disposable vinyl gloves.
2.
Unplug the Power Cord (19) from the electrical outlet.
3.
Discharge the Conductor Pole (25) to the Ground Clip (15).
4.
Disconnect the air hose from the Spray Gun (2).
5.
Remove the Powder Cup (4) and pour any remaining powder back into it’s original
container.
WARNING: Powder clouds/mist are explosive. Before cleaning, remove any possible
ignition source from the work area .
6.
Using compressed air, blow out the Cup and all other parts that have collected
powder. Make sure to wear the dust mask first.
7.
Uncontaminated powder residue can be stored and reused.
8.
Store Powder Coating System in its box. Place the box and powder container in a
clean and dry location.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 12
PARTS LIST
Part #
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
Description
Spray Gun Pipe
Spray Gun
Air Outlet Pipe
Powder Cup
Air Input Pipe
Trigger
Regulating Screw
Pressure Reducer Valve
Disposable Moisture Separator
Quick Adapter
Control Box
Power Indicator Light
Activation Indicator Light
Power Switch
Ground Clip
Foot Switch
Fuse
Foot Switch Cable
Power Cord
Accessories
Scatter tip (Large)
Scatter Tip (Small)
Emitter
Scatter Tip (Medium)
Conductor Pole
Ground Wire
High Voltage Wire
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as
replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 94244
For technical questions, please call 1-800-444-3353
Page 13
ASSEMBLY DRAWING
SKU 94244
For technical questions, please call 1-800-444-3353
Page 14
WARRANTY
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 94244
For technical questions, please call 1-800-444-3353
Page 15