Dedicated Micros SD26X Instruction manual

SPEED DOME CAMERA
Instruction Manual
Model No. :
DM/CAM/SD18X/A
DM/CAM/SD22X/A
DM/CAM/SD26X/A
Please read this manual thoroughly before use and keep it handy for future reference.
Rev.070514
Warnings and Cautions
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instruction in the literature
accompanying the product.
II
FCC COMPLIANCE STATEMENT
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO
PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN
THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL
AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE
USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN
EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER
MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.
III
IMPORTANT SAFEGUARDS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that product heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
15. Use Certified/Listed Class 2 power supply transformer only.
IV
Table of Contents
Chapter 1 — Introduction ............................................................................................................. 1
1.1 Features...............................................................................................................................................1
Chapter 2 — Installation and Configuration .............................................................................. 2
2.1 Package Contents................................................................................................................................2
2.2 Connector board of Dome Camera......................................................................................................3
2.3 Setting Dome Camera Termination......................................................................................................4
2.4 Setting Dome Camera Address (ID) ....................................................................................................5
2.5 Setting Dome Camera Protocol ...........................................................................................................6
2.6 Connections .........................................................................................................................................7
Connecting to the RS-485/ 422 ............................................................................................................7
Connecting Video out connector ..........................................................................................................7
Connecting Alarms ...............................................................................................................................7
Connecting the Power ..........................................................................................................................7
2.7 Getting Started .....................................................................................................................................8
Chapter 3 — Program and Operation ......................................................................................... 8
3.1 Dome Camera Selection......................................................................................................................8
3.2 Accessing On-Screen Menu Utility ......................................................................................................9
3.3 Auto Scan.............................................................................................................................................9
3.4 Preset................................................................................................................................................. 11
3.5 Shortcut of Preset Program ...............................................................................................................12
3.6 Tour ...................................................................................................................................................13
3.7 Pattern ...............................................................................................................................................14
3.8 Alarm..................................................................................................................................................15
3.9 Area Title ............................................................................................................................................16
3.10 Privacy Zone ....................................................................................................................................17
3.11 Camera – DM/CAM/SD18X/A , SD26X/A MODEL .........................................................................18
Focus Control .....................................................................................................................................18
WB (White Balance) Control ..............................................................................................................19
AE Control ..........................................................................................................................................19
Line Lock Control................................................................................................................................20
Night Shot Menu .................................................................................................................................20
V
3.12 Camera – DM/CAM/SD22X/A MODEL ...............................................................................................21
Focus Control .......................................................................................................................................21
WB (White Balance) Control ................................................................................................................22
AE Control ............................................................................................................................................22
Line Lock Control .................................................................................................................................23
3.13 Camera - DM/CAM/SD26X/A MODEL ..............................................................................................23
3.14 Dome Setup.........................................................................................................................................24
Language Setup ...................................................................................................................................24
Home Function Setup...........................................................................................................................24
OSD Display.........................................................................................................................................25
View Direction ......................................................................................................................................25
Dome OSD Display ..............................................................................................................................25
Area Display .........................................................................................................................................25
View Angle Setup .................................................................................................................................26
Panning Range.....................................................................................................................................26
Flip........................................................................................................................................................26
Tilt Over Angle ......................................................................................................................................26
Initialize Data ........................................................................................................................................27
Origin Offset .........................................................................................................................................27
Dome Reset ........................................................................................................................................27
System Information ..............................................................................................................................27
Appendix A — Specifications .................................................................................................... 28
Appendix B — Troubleshooting ................................................................................................ 30
Appendix C — Glossary ............................................................................................................. 31
Appendix D — Bubble Ring ...................................................................................................... 33
Appendix E — Short Cut Key (Pelco protocol) by KBS3 keyboard ...................................... 34
VI
Chapter 1 — Introduction
1.1 Features
• 240 Preset positions.(1-32,35-59:by PELCO-P protocol)
• 8 Tours consist of Preset, Pattern, Auto-Scan and other Tours can be programmed with over
300 functions and Preset location. While moving, each Preset scan can be watched in smooth
Vector Scan mode.
• 8 Auto Scans including vector scan and 1 Endless Auto-Scan.
• 4 Patterns (240second).
• 8 Privacy zones.
• 8 Alarm inputs / 4 Aux outs (NC & NO).
• Variable speed from 0.1°/sec to 90°/sec.
Pan / Tilt speed is inversely proportional to the zoom ratio.
Maximum speed is 380°/sec when preset command.
• Programmable user preferences (alarm, preset, title, etc.).
• Up to 999 selectable camera addresses..
• Built-in RS-485/422 receiver driver.
•Clear bubble with black liner (shelter) for concealing the camera.
• Optional Tinted Bubble, Indoor & Outdoor pendant housing with heater & blower, Indoor Flush
mount, Parapet mount & Roof Top mount.
1
Chapter 2 — Installation and Configuration
2.1 Package Contents
The package contains the following.
Dome Camera
Bubble Ring
Instruction Manual (This Document)
Assembly Screws for Attaching a dome
Plastic Anchor
10Pin Connector
12Pin Connector
………………………1
………………………1
………………………1
………………………3
………………………3
………………………1
………………………2
CAUTION: Be sure to have caution labels (E version only) on both the body and the base
of the camera. Different version will not support input and output.
The dome camera is for use in surface mounting applications and the mounting surface should
be capable of supporting loads up to 10lb (4.5kg).
The dome camera’s base should be attached to a structural object, such as hard wood, wall stud
or ceiling rafter that supports the weight of the dome camera.
CABLE ENTRY
SURFACE(CEILING)
Unlock
Lock
BASE
Align extruded tap in the base to
the Keyhole on the pcb in the body
Lock
BODY
Figure 1 – Installation
2
2.2 Connector board of Dome Camera
Figure 2 – CONNECTOR BOARD
3
The dome camera must be installed by qualified service personnel in accordance with all local
and federal electrical and building codes. The system should be installed according to Figures 2
through 6.
Termination Switches
SW1
ON KSD02H
9A 1
2
on
1 2 3 4
1 2 3 4
4 56
4 56
78
1
23
4 56
1
on
8
78
S4
23
4 56
on
8 1
23
23
4 56
78
9 01
23
4 56
S5
9 01
78
9 01
S1
S6
9 01
78
9 01
S2
9 01
78
S3
8
Address(ID) and Protocol
selection Switches
23
Figure 3 – Layout of Switches
2.3 Setting Dome Camera Termination
The device which is connected at end of line, whether it is a dome camera or a keyboard
controller, must have the cable for communication terminated by setting the appropriate DIP
switch. Without proper termination, there is potential for control signal errors. Total length of the
cable for communication should not exceed 4,000ft (1.2km).
SW1
ON KSD02H
9A 1
1
2
Terminated
ON
ON
Not terminated
OFF
OFF
SW1
2
Figure 4 – Setting Dome Camera Termination
4
2.4 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID). When installing
multiple dome cameras using a multiplexer, it is suggested that the dome camera address match
the multiplexer port number.
If you want to set the address more than 999, you should contact the service provider.
Example: Port 1 = Dome 1, Port 2 = Dome 2 … Port 16 = Dome 16. If more than 16 dome
cameras are installed using two or more multiplexers, ID of the dome camera should be ID of
MUX x No. of camera IN. (e.g. multiplexer ID= n, Camera IN= m then ID of Dome =16x(n-1)+m )
1
8
1
45 6
23
45 6
8
1
45 6
23
78
S3
0
0
.
9
DOME ID
1
2
.
999
S2
0
0
.
9
9 01
23
S1
78
9 01
S2
9 01
78
S3
8
Refer to Figures 4-5 for setting the dome camera address (ID) and protocol selection.
Figure 5 – Setting Dome Camera Address (ID)
5
S1
1
2
.
9
2.5 Setting Dome Camera Protocol
If a dome camera is to be installed with a Dedicated Micros KBS3 keyboard, select the switch as
the same as the Dedicated Micros DVR.
Consult service personnel if a dome camera is installed with device other than a keyboard
controller.
NTSC
S/W
D1
S4-1
D2
S4-2
D3
S4-3
D4
S4-4
on
on
PAL
S4
D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12
4
3
2
1
4
3
1
2
S4
3
4
1
2
S5
RS-422
Off
Disable
NTSC
ENDLESS
RS-485
FUNCTION
Alarm
NTSC/PAL
Pan mode
RS-422/RS-485
S4
D5
S5-1
S6
On
Enable
PAL
Camera
Baud rate
Protocol
RS-422/
RS-485
NTSC/PAL
Alarm
Note: When you use the
Pelco-P protocol with 4800bps
in the DVR, you should
change the baud rate to 4800
bps of the dome.
D6
D7
S5-2 S5-3
Off
Off
Off
Off
Off
Off
On
On
On
On
Off
On
On
Off
Off
On
On
On
Off
On
Off
On
Off
On
D8
S5-4
Off
Off
Off
Off
On
On
On
On
F2,F2E,P,D,E & Ph Protocol
(Default)
Reserved
S 422
Reserved
V Protocol
Reserved
D Color
Reserved
D9
D10
S6-1 S6-2
Off
Off
Off
On
On
Off
On
On
Off
Off
Off
On
On
Off
On
On
D11
S6-3
Off
Off
On
On
Dedicated Micros DVR
Defaults(9600bps)
ON
OFF
PROTOCOL
D12
S6-4
Off
On
Off
On
BAUD RATE
2400 bps
4800 bps
9600 bps (Default)
19200 bps
38400 bps
57600 bps
115200 bps
230400 bps
CAMERA
Default cameras (Default)
Reserved
Reserved
Reserved
D1
D2
D3
D4
D5
D6
D7
D8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
D9
D10
D11
D12
OFF
OFF
OFF
ON
Figure 6 – Protocol Selection Switches
6
2.6 Connections
• Connecting to the RS485/ 422
The dome camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS485 half-duplex, RS422 duplex or simplex serial communications
signals. Connect Marked Rx+(Tx+), Rx-(Tx-) to Tx+ and Tx- of the RS485 control system.
If control system is RS422, connect Rx+(Tx+), Rx-(Tx-) and Rx+, Rx- of the dome camera to
Rx+, Rx- and Tx+, Tx- of the control device respectively.
• Connecting Video out connector
Connect the video out(BNC) connector to the monitor or video input.
• Connecting Alarms
AL1 to 8 (Alarm In)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the AL (Alarm In) and GND (Ground) connectors.. See
Chapter 3 — Program and Operation for configuring alarm input.
GND (Ground)
NOTE: All the connectors marked GND are common.
Connect the ground side of the Alarm input and/or alarm output to the GND connector.
NC(NO)1 TO 4 (Normal Close or Normal Open : Alarm Out)
The dome camera can activate external devices such as buzzers or lights. Connect the device to
the NC(NO) (Alarm Out) and COM (Common) connectors. See Chapter 3 — Program and
Operation for configuring alarm output.
• Connecting the Power
Connect the power of AC 24V 850mA to the dome camera.
Use certified / Listed Class 2 power supply transformer only.
7
2.7 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration
sequence.
PRESET No.
CAMERA TITLE
001 PRESET
PRESET TITLE
or AREA TITLE
CAMERA ID
INFORMATION
DISPLAY
FUNCTION
UNDER RUNNING
EMPTY DATA !
T001
ALARM:1
DOMEID:0001
W→360.0,090.0
ALARM DISPLAY
PAN & TILT ANGLE
VIEW DIRECTION
OSD Position
Chapter 3 — Program and Operation
3.1 Dome Camera Selection
The Dedicated Micros KBS3 keyboard is the recommended device for controlling the PTZ
camera. Before you program or operate a dome camera, you must select the dome camera by
pressing the camera number key.
Note: Install the dome with the same dome ID as the camera input number to camera
input port of the DVR. Refer to the manual of the DVR.
8
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by pressing PRESET .
The DVR displays the following pop-up window:
Goto preset
Enter PRESET number
Pressing 95 will display the following On-screen menu.
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
ALARM
AREA TITLE
PRIVACY ZONE
CAMERA
DOME SETUP
EXIT(ESC TO EXIT)
NOTE: Quick pressing buttons may not operate, press a button slowly.
NOTE: When you can’t enter the menu, first press PRESET + 96 and PRESET + 95 again.
NOTE: The operation below is explained based on the KBS3 keyboard
3.3 Auto Scan
The Auto scan supports up to 8 programmed angles at user-programmable speeds. Follow
these steps to program Auto Scan:
AUTO SCAN SETUP
SCAN 01
:
SPEED(MODE) :
START ANGLE :
END ANGLE
:
SCAN DIR.
:
SWAP
:
SAVE AND EXIT
AUTOSCAN01
FAST VECTOR
127.1, 027.7 X7
157.7, 080.7 X13
CCW
OFF
(ESC TO CANCEL)
HOLD DOWN CTRL KEY
WHILE SELECT POSITION.
9
SPEED(MODE) :
NORMAL1~NOMAL9,SLOW VECTOR,FAST VECTOR
NORMAL1 (SLOWER) ↔ NORMAL9 ( FASTER)
SLOW VECTOR, FAST VECTOR : Move from start point to end point
including tilt and zoom simultaneously and linearly. In case of 22x model,
zoom is fixed at more wide angle and the zoom magnification information
is not displayed.
1. Press PRESET + 60 key to enter Auto Scan menu directly. Or press PRESET + 95 keys to
display the main menu on the monitor. Scroll to Auto Scan and push the Joystick to the right.
2. Select an Auto Scan number by pushing the Joystick left or right.
3. Twist the Joystick to enter the title by scrolling through the alphanumeric characters and
pushing the handle to the right or left to move to the next space. Press PRESET + 94 keys
or push the Joystick down to finish title mode.
4. Push the Joystick downward to select “Speed” and set the speed by twisting the Joystick
clockwise or counterclockwise to select the auto scan speed.
5. When finish entering the title, select “START ANGLE” with the Joystick. Press PRESET +
95 keys, then select the start position and the zoom using the Joystick. Current position will
be displayed. Press PRESET + 95 keys to complete the selection of the start position.
6. Push the Joystick downward to select “END ANGLE.” Press PRESET + 95 keys, then move
the Joystick to select the end position and the zoom. The end position angle should be larger
than start position. Press PRESET + 95 key to complete the selection of the end position.
7. Select Save and Exit by pushing the Joystick to the right. Press PRESET + 96 keys to exit
the program without saving.
NOTE: Using the Tour mode in conjunction with preset and Auto Scan, you can make the camera
travel from one preset position to another preset position at a specific speed. (Pan only)
a. Before entering the Auto Scan menu, select a preset position as a starting point for Auto Scan.
Example: PRESET + 02 and do step 1 to 4. Instead of step 5, just press PRESET + 95 key
twice at the start angle position, the current position will be displayed as a start position.
b. Save and exit from the menu.
c. In normal mode, call a preset to be the end point of scan. Press PRESET + 03 then press
PRESET + 60 keys to enter the Auto Scan menu. Move the cursor position to END ANGLE.
Just press PRESET + 95 key twice at the end angle position. Do steps 7.
Example: Preset 001>002>003>004>005>006, Auto Scan 01 starts at 002, ends at 003,
Auto Scan 02 starts at 005, ends at 006. If you set Tour 01: 001, 002, A01, 004, A02.
1 Î 2 2~3 Î 4 Î 5~6 Î1 Î 2 2~3 ……
Where
Î : Quick move, ~ : Programmed speed by Auto Scan.
Also you can execute Endless Auto Scan which is to turn one direction continuously by Pressing
PRESET + 99 or AUTOPAN.
10
3.4 Preset
If you need to view specific places routinely, you should program presets. A preset is a
programmed video scene with automatic pan, tilt, zoom, focus and iris settings. Once
programmed, pressing a PRESET button and entering the number on your keyboard
automatically calls up the preset. In addition, presets may be assigned to alarm actions or as the
“home” position for the dome camera.
There are three pages of preset menu, each page can hold 80 presets. Pages can be scrolled
by pushing the Joystick to the Left or Right on the first or last No. of Preset.
PRESET SETUP
NO. 001: xxxxxxxxxxxxxxxx
FOCUS : AUTO (MANUAL)
IRIS
: AUTO (MANUAL)
DWELL : 03 SEC(3~99)
1234567890 1234567890
00█***======01==========
02==========03==========
04==========05==========
06==========07==========
JOY-LEFT TO PREV. PAGE
SAVE AND EXIT(ESC TO CANCEL)
NOTE: In case of the KBS3 keyboard, you can call the preset 1-32, 35-59.
NOTE: When you call the preset number under 10, you should press 0 first. (1: press 0 + 1)
x
=
*
█
: 16 digits of title for preset label
: blank preset position
: position has the preset
: Current cursor position
Follow steps below to store the Preset positions:
1. Press PRESET + 95 to display the main menu. Select the Preset option by using the
Joystick to the right. (Press PRESET + 93 to go directly to the Preset menu without going
through the main menu.)
2. Select the blank preset position to be stored by pushing the Joystick up, down, right, or left.
3. The position, which is marked with *, already has the preset view assigned. To review the
stored preset, press PRESET + 93 key on the *,The camera will show the stored preset
view.
4. After selecting a blank position, press PRESET + 95, Use the Joystick to control the
direction of the camera and lens.
11
5. After aiming the camera (view direction and lens control), press PRESET + 95 again.
6. Then twist the Joystick handle or press ZOOM IN or ZOOM OUT Key to store the selected
view. The position number will be displayed and the user will be prompted to enter a preset
title.
7. Enter the title for the preset position using the Joystick. (Rotate handle clockwise and
counterclockwise or press ZOOM IN or ZOOM OUT Key to scroll through the alphanumeric
characters, push the handle to right or left to select next or previous digit.)
8. When you are finished entering the title, push the Joystick downward. Set the focus by
pushing the Joystick to the right or left. Set the IRIS value in the same manner as the focus.
9. Move to the DWELL setting by pushing the Joystick down. Twist the Joystick clockwise or
counterclockwise to increase or decrease dwell time of the preset position.
10. Push the Joystick downward then the blank preset position changes *.
11. Repeat steps 2 through 10 for each additional preset position.
To select the next page of presets, scroll the page by pushing the Joystick to the Left on the
first and last columns of the menu. (In using the KBS3 keyboard with the PELCO-P protocol, you
can call the preset 1-32, 35-59.)
12. To edit the title of a stored preset, use the Joystick to position the cursor on the desired
preset position (*). Press the PRESET + 93key to recall the stored preset. Twist the zoom
handle clockwise to enter the preset title field. Preset titles are useful with short cut preset
programming.
13. Select Save and Exit by pushing the Joystick to the right. Press PRESET + 96 to exit the
Preset menu without saving.
NOTE: Press PRESET + 91 at programmed position to delete a programmed preset view.
NOTE: In the normal display mode, an alternate method is to press the PRESET button two times
quickly in the DS2 model.
3.5 Shortcut of Preset Program
After selecting a view to be stored (direction of the camera, zoom and focus), press and hold
PRESET until the pop-up window below displays in DS2 model.
Save preset
Enter PRESET number
1-99
Press number you want up to 99.The old saved preset number is overwritten.
NOTE: Camera 10 is number 0 and you should press 0 and 1 to enter 1.
NOTE: In case of the KBS3 keyboard, you can call the preset 1-32, 35-59 and the other preset
numbers can be used in the tour, the alarm and the home function.
12
3.6 Tour
There are 8 programmable Tours. Each Tour consists of up to 42 Preset positions, Patterns,
Scans or other Tours (second-level). Using second-level Tours, it can be expanded to over 300
functions in a single Tour. However second level Tours will be ignored when called by a Tours.
The following example illustrates this concept:
If
Tour1 has Preset1ÎPreset2ÎTour2ÎTour3 and
Tour2 has Preset3ÎPreset4 ÎPreset5 ÎTour4and
Tour3 has Preset6ÎPattern 1and
Tour4 has Preset7.
Tour1 executes as follows:
Preset1 Î Preset2 Î Preset3 Î Preset4 Î Preset5 Î Preset6 Î Pattern1 Î
Preset1 Î ... (Repeat)
Tour2 executes as follows:
Preset3 Î Preset4 Î Preset5 Î Preset7 Î Preset3 … Repeat
(Tour4 is still valid if called directly from Tour2.)
TOUR 01:xxxxxxxxxxxxxxxx
SCAN TYPE:NORMAL
=== === 003 === === === ===
A08 === === === === === ===
=== T02 === 001 === === ===
=== === === T08 === === ===
=== === === === === === ===
=== === === === === === ===
SAVE AND EXIT(ESC TO CANCEL)
PRESS FUNCTION KEY AND ROTATE
JOYSTICK TO SELECT NUMBER.
xxxxx
===
SCAN TYPE
DWELL
003
A08
P01
T02
: 16 digits of title for tour label
: blank preset position
: Max (Normal)/ Slow V. Scan/ Fast V. Scan
: 03-99 Sec
: Preset 003 (1~240)
: Auto Scan 08 (1~8)
: Pattern 01 (1~4)
: Tour 02
(1~8)
Follow the steps below to program the Tours:
1. Press PRESET + 95 to display the main menu on the monitor. Scroll to Tour and push the
Joystick to the right to enter the Tour menu. Or just press the Tour key on the keyboard
2. Choose an empty location to be programmed by pushing the Joystick up, down, right, or
left.
3. To see a stored preset view, use the Joystick to move the cursor to a stored position. By
pressing PRESET + 93 keys, the camera will move to the stored Preset view.
13
4. To add a stored preset as a Tour, twist the Zoom handle or press Zoom Key (Programmed
preset will scroll). To remove a stored preset from the Tour, press PRESET + 91 keys,
blank position mark (===) will be displayed. You can overwrite the programmed position.
5. To place functions other than preset, press Tour(PRESET + 70), Pattern(PRESET + 80),
or Scan(PRESET + 60 ) for Tour, Pattern or Auto Scan respectively.
6. Repeat Step 2 through 5 for each desired position. Each title will be displayed on top of the
line.
7. Up to 36 Presets, Tours, Patterns Scans can be selected for a Tour. You can expand the
Tour sequence by calling other programmed tours. Push the Joystick handle to right or left
while the cursor is on the top of the line (TOUR 01) to select another page of the Tour menu.
(TOUR 01)
8. You can enter a title for the selected Tour by twisting the Joystick while the cursor is on
the top of the line (TOUR 01). Rotate the handle clockwise or counterclockwise to scroll
through the alphanumeric characters. Push the handle to the right or left to select the next
or previous digit.
9. Select Save and Exit by pushing the Joystick to the right. Press PRESET + 96 to exit the
program without saving.
NOTE: Press PRESET + 91 key at a programmed position to delete programmed function.
In the Tour mode, in conjunction with preset and Auto Scan, you can make the camera
travel from a preset position to another preset position at a specific speed.
Example: Preset 001>002>003>004>005>006, Auto Scan 01 starts at preset 002, ends at
preset 003, Auto Scan 02 starts at preset 005, ends at preset 006; Tour01: 001, 002, A01, 004,
A02.
1 Î 2 2~3 Î 4 Î 5~6, repeat
where Î : Quick move, ~ : Programmed speed
3.7 Pattern
The Pattern feature records user control of the selected dome camera for up to 240 seconds. Up
to four 4 patterns can be stored and played back by pressing PRESET + 81 ~ 84 keys
subsequently. Alternatively, the PATROL + 3 digits (001-004) can also be pressed on the
keyboard of the DS2 model.
PATTERN SETUP
NO.
01 :
02 :
03 :
04 :
TOTAL
TITLE
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
SEC
000
041
010
020
071
SAVE AND EXIT(ESC TO CANCEL)
HOLD DOWN CTRL KEY
WHILE RECORDING.
Follow steps below to program the Pattern:
14
1. Press PRESET + 95 keys to display the main menu on the monitor.
2. Scroll down to PATTERN and push the Joystick to the right. Or simply press the PRESET
+ 80 key rather than use the Main Menu.
3. Select the empty Pattern number to be programmed by pushing the Joystick Up or Down.
If last column is not 000, a pattern has already been recorded. Patterns can be over written.
4. Press the PRESET + 95 keys and control the camera direction and zoom with the Joystick.
Your controls will be automatically recorded until you press the PRESET + 95 keys again.
You can repeat this procedure until you have the pattern you want. Previously recorded
patterns will be overwritten each time you do this.
5. Scroll down to the Save and Exit option and push the Joystick to the right to save and exit.
6. You can title the selected Pattern by twisting the Joystick. Rotate the handle clockwise or
counterclockwise to scroll through the alphanumeric characters, push the handle to right or
left to select next or previous space.
7. Pressing PRESET + 96 will not save your information and exits to the previous mode.
Press the PRESET + 91 key at any programmed position to delete that programmed
pattern.
NOTE: If total recording time reaches 240 seconds, it will automatically stop for a moment and
restart recording. Previous data will be overwritten.
3.8 Alarm
ALARM SETUP
NO PRI PRS IN OUT HLD LATCH
01 1 001 OFF OFF 3
OFF
02 0 A01 OFF OUT1 3
OFF
03 1 240 NO OUT1 3
OFF
04 2 001 NC OUT4 3
OFF
05 1 001 OFF OFF 3
OFF
06 8 001 OFF OUT1 3
OFF
07 1 240 NO OUT1 3
OFF
08 2 001 NC OUT4 3
OFF
SAVE AND EXIT(ESC TO CANCEL)
NO
PRIO
PRS
IN
OUT
HOLD
LATCH
: Alarm input number
: Lower No. has higher priority, Equal priority alarms will be serviced repeatedly.
: Stored preset number to be called by alarm.
: NO/NC - normally open /Closed OFF - ignore
: OUT1~OUT4 - Relay out 1,2,3,4, OFF - No output.
: Alarm will be held for programmed time (03 to 99 seconds)
: ON - Shows all alarms including past alarm, OFF - Shows activated alarms only.
There are 8 levels of priority. “0” is the highest priority and can be selected Autoscan, Pattern or
Tour only. “1” - “8” can be selected Preset only. During responding “0” priority alarm, other
alarms won’t be serviced until the “0” priority action is completed.
15
1. Press Menu to display the main menu on the monitor. Select the Alarm option by pushing
the Joystick up or down and push to right to enter the detail menu.
2. Select the alarm input number by pushing the Joystick up or down and select the column
you wish to setup. Selected position will be highlighted.
3. Select the Preset, Status of Input (NC/NO/OFF), and Output (OUT1~4/OFF) by pushing the
Joystick to the right or to the left.
4. To increase or decrease the preset number or to change the status or output number, twist
the Joystick clockwise or counterclockwise. In case of preset, programmed preset number
will be scrolled.
5. Select the Save and Exit option by pushing the Joystick up or down. Save and exit the
program by pushing the Joystick to the right. Press PRESET + 96 to exit the program
without saving.
3.9 Area Title
Enter a specific name on programmed angle between START and END. For the screen below,
when the camera points at an angle between 124.3° to 359.5°, ABC will be displayed on the
screen.
AREA TITLE SETUP
NO
TITLE
START END
01 ABC
124.3 359.5
02 xxxxxxxxxxxxxxxx ===== =====
03 xxxxxxxxxxxxxxxx ===== =====
04 xxxxxxxxxxxxxxxx ===== =====
05 xxxxxxxxxxxxxxxx ===== =====
06 xxxxxxxxxxxxxxxx ===== =====
07 xxxxxxxxxxxxxxxx ===== =====
08 xxxxxxxxxxxxxxxx ===== =====
SAVE AND EXIT(ESC TO CANCEL)
HOLD DOWN CTRL KEY TO MOVE
PAINNING AND SET AREA ANGLE.
There are 16 programmable numbers. Pages can be scrolled through by pushing the Joystick
to the Left or Right on the first or last column of the menu. Pushing the Joystick to left on the
“NO” column of the menu to scroll to the previous page. Push the Joystick to right on the “END”
column to go to the next page.
1. Press PRESET + 95 to display the main menu on the monitor. Select the Area Title option
by pushing the Joystick up or down and push to right to enter the detail menu.
2. Select the area number by pushing the Joystick up or down. Select Start, End or number
column to be set by pushing the handle to the right or left. The selected column will be
highlighted.
3. To enter area title, select the number column and rotate the handle clockwise or
counterclockwise. You can select alphanumeric characters by rotating the handle. Move to
the next character by pushing the Joystick to the right. To finish entering the title, push the
Joystick down.
16
4. To adjust panning limit, press the PRESET + 95 keys on the start or end field. Then use
the Joystick to go the desired direction. Press the PRESET + 95 keys to finish. The end
limit must be in an increasing direction. (Start < End).
5. When you press PRESET + 95 keys twice, the current position of the pan will be printed in
the highlighted column. With this feature, you can easily set the next start point as the
previous end point.
6. Select the Save and Exit option by pushing the Joystick up or down. Save and exit the
program by pushing the Joystick to the right. Press PRESET + 96 to exit the program
without saving.
Pressing the PRESET + 91 key will delete programmed data. (Angles will be turned ====
immediately.)
3.10 Privacy Zone
Hide up to 8 unwanted views in a camera.
PRIVACY ZONE SETUP
NO
TITLE
METHOD
01 xxxxxxxxxxxxxxxx
ON BLOCK
02 xxxxxxxxxxxxxxxx OFF V.OFF
03 xxxxxxxxxxxxxxxx NONE ====
04 xxxxxxxxxxxxxxxx NONE ====
05 xxxxxxxxxxxxxxxx NONE ====
06 xxxxxxxxxxxxxxxx NONE ====
07 xxxxxxxxxxxxxxxx NONE ====
08 xxxxxxxxxxxxxxxx NONE ====
SAVE AND EXIT(ESC TO CANCEL)
1. Press PRESET + 95 keys to display the main menu on the monitor. Select the Privacy
Zone option by pushing Joystick Up or Down and push to right to enter the detail menu.
2. Select the privacy zone number by pushing the Joystick up or down.
3. To enter the zone name, rotate the handle clockwise or counterclockwise. You can select
alphanumeric characters by rotating the handle. Move to the next character position by
pushing the Joystick to the right. To finish entering the title, push the Joystick down or
press the PRESET + 94 key.
4. To adjust the “marked” (privacy) area, press PRESET + 95 keys and then use the Joystick
(direction and zoom) until you get desired view. Press PRESET + 95 keys again, the right
column will be set to ON.
5. You can overwrite an existing zone. Use the Home key to delete the marked zone, or push
the Joystick to the right or left to turn the stored zone On or Off.
6. Select the Save and Exit option by pushing the Joystick up or down. Save and exit the
program by pushing the Joystick to the right. Press PRESET + 96 to exit the program
without saving.
Note: Press PRESET + 91 keys to delete programmed privacy zone.
17
3.11 Camera – DM/CAM/SD18X/A, SD26X/A MODEL
NOTE: The menu features will vary depending on the camera module installed in your dome
camera.
CAMERA SETUP
FOCUS CONTROL
WB CONTROL
AE CONTROL
LINE LOCK CONTROL
SHARPNESS
: 9
BACK LIGHT
: OFF
DIGITAL ZOOM : OFF (2X/4X/MAX)
NIGHT SHOT CONTROL
SAVE AND EXIT(ESC TO CANCEL)
SHARPNESS
BACK LIGHT
Digital ZOOM
The higher the value,the more edges in the picture will be enhanced.
Objects in front of bright backgrounds will be clearer with BLC ON.
OFF : Zoom range is limited to the optical.
2x : Zoom is extendable up to 2x of digital range.
4x : Zoom is extendable up to 4x of digital range.
MAX: Zoom is extendable Max digital zoom range.
• FOCUS CONTROL
FOCUS SETUP
MODE
: AUTO
AF SENSITIVITY
: HIGH
EXIT(ESC TO EXIT)
MODE: AUTO / MANUAL
Use manual mode in normal use.
AF SENSITVITY
: HIGH / LOW
HIGH: Use this option when shooting fast motion.
LOW: Offers better focus stability. In low luminance conditions, Auto Focus stops
operation even when brightness changes, enabling stable images of moving
objects.
CAUTION: Avoid continuous, 24-hour use of the auto focus. This will shorten the
lifespan of the lens.
18
• WB (White Balance) CONTROL
WB SETUP
MODE
:
AUTO
R GAIN :
210
B GAIN :
155
EXIT(ESC TO EXIT)
MODE
MANUAL / AUTO / INDOOR / OUTDOOR / ONE PUSH / ATW
RGAIN
0 ~ 255
BGAIN
0 ~ 255
Use the ATW mode for normal use.
RGAIN / BGAIN modes are controllable only in MANUAL Mode
Push the Joystick to the right or left to change.
NOTE : “ONE PUSH” means that when rotating the Joystick handle for a moment the lens moves
to adjust the focus for the subject. The focus lens then holds that position until the Joystick
handle rotation.
• AE CONTROL
AE SETUP
MODE
: FULL AUTO
SLOW SHUTTER : AUTO
IRIS
: F2.4
GAIN
: 0 DB
BRIGHT
: 14
SHUTTER
: 1/60
EXIT(ESC TO EXIT)
MODE
FULL AUTO / MANUAL / IRIS PRIO / SHUTTER PRIO / BRIGHT
SLOW SHUTTER AUTO / MANUAL ----- AUTO effect only FULL AUTO mode
IRIS
CLOSE / F22 / F19 / F16 / F14 / F11 / F9.6 / F8.0 / F6.8 / F5.6 / F4.8 /
F4.0 / F3.4 / F2.8 / F2.4 / F2.0 / F1.6 / F1.4
GAIN
0 / 2 / 4 / 6 …… / 28 / -3 DB
BRIGHT
0, 1, 2, 3, 4 ..... 29, 30,31
SHUTTER
1/1 , 1/2 , 1/4(3), 1/8(6). .. 1/4000, 1/6000, 1/10000
EXIT (ESC TO EXIT)
NOTE : Values in ( ) are for PAL Camera.
19
• LINE LOCK CONTROL
LINE LOCK SETUP
MODE
:
INTERNAL
PHASE :
125
EXIT(ESC TO EXIT)
MODE
INTERNAL / EXTERNAL
PHASE
0~255
EXIT (ESC TO EXIT)
Adjusts phase of picture with other
cameras in EXTERNAL mode.
• NIGHT SHOT MENU
The NIGHT SHOT option removes the IR cutoff filter of the camera and makes the camera
sensitive to near infrared.
NIGHT SHOT SETUP
MODE
: MANUAL
LOCAL CONTROL
: OFF
EXIT(ESC TO CANCEL)
MODE:
MANUAL / AUTO / GLOBAL
AUTO:
Camera goes in to B&W mode at low light.
GLOBAL:
NO USE
MANUAL:
Controlled by the local setting value.
LOCAL CONTROL: ON/OFF will enable and disable Night Shot mode of an individual camera.
20
3.12 Camera – DM/CAM/SD22X/A MODEL
CAMERA SETUP
FOCUS CONTROL
WB CONTROL
AE CONTROL
LINE LOCK CONTROL
SHARPNESS : 10
BACK LIGHT
: OFF
DIGITAL ZOOM : OFF (MAX)
SAVE AND EXIT(ESC TO CANCEL)
SHARPNESS
BACK LIGHT
Digital ZOOM
The higher the value, the more edges in the picture will be enhanced
User can adjust sharpness level from 0 to 20. Level 20 is default
Objects in front of bright backgrounds will be clearer with BLC ON.
OFF: Zoom range is limited to the optical.
MAX: Zoom is extendable Max digital Zoom range.
• FOCUS CONTROL
FOCUS SETUP
MODE
: AUTO
EXIT(ESC TO EXIT)
MODE : AUTO / MANUAL
Use manual mode in normal use.
CAUTION: Avoid continuous, 24-hour use of the auto focus. This will shorten the
lifespan of the lens.
21
• WB (White Balance) CONTROL
WB SETUP
MODE
:
AWB
R GAIN :
85
B GAIN :
85
EXIT(ESC TO EXIT)
MODE
AWB / WAWB / INDOOR / DOUDOOR / MANUAL
WAWB
Wide range auto white balance mode.
RGAIN
0 ~ 255
BGAIN
0 ~ 255
Use the AWB mode for normal use.
RGAIN / BGAIN modes are controllable only in MANUAL Mode
Push the Joystick to the right or left to change.
• AE CONTROL
AE SETUP
MODE
SLOW SHUTTER
IRIS
GAIN
BRIGHT
SHUTTER
WDR MODE
EXIT (ECS TO
MODE
SLOW SHUTTER
IRIS
GAIN
BRIGHT
SHUTTER
WDR MODE
: FULL AUTO
: AUTO
: F1.6
: 2DB
: 30
: AUTO
: ON
EXIT)
FULL AUTO / SHUTTER PRIO / IRIS PRIO / AGC / MANUAL
AUTO / OFF / ON (MANUAL, SHUTTER PRIO MODE ONLY)
CLOSE, F1.6 / F2.0 / F2.8 / F4.0 / F5.6 / F8.0 / F11 / F16 / F22 / F32
OFF, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20 DB
User can adjust brightness level (0~ +90). Level 30 is default.
1/1, 1/2, 1/3, 1/6, 1/10, 1/30, 1/60, 1/100, 1/125, 1/250, 1/500, 1/1000,
1/2000, 1/5000, 1/10,000
(1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/100, 1/120, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/10,000)
Wide Dynamic Range Technology uses two shutter speeds in alternative
video fields-high and normal- every 60th (or 50th) of a second and
combines two fields into one progressive scan frame. It allows every detail
to be captured accurately even if one portion of an image is brilliantly
bright while other portions are dark.
NOTE : Values in ( ) are for PAL Camera.
22
• LINE LOCK CONTROL
LINE LOCK SETUP
MODE :
INTERNAL
PHASE :
125
EXIT(ESC TO EXIT)
MODE
INTERNAL / EXTERNAL
PHASE
0~255
EXIT (ESC TO EXIT)
Adjusts phase of picture with other
cameras in EXTERNAL mode.
3.13 Camera – DM/CAM/SD26X/A MODEL
Eclipse of the Lens:
The eclipse phenomenon occurs with this model. This is because a sufficient amount of aperture
is not available due to the CCD size and the lens structure of this model. However, it has been
verified that the eclipse will not be visible in the case of a more than 90% effective image. For
your reference, see the following diagram.
23
3.14 Dome Setup
CONFIGURATION MENU
LANGUAGE SETUP
HOME FUNCTION SETUP
OSD DISPLAY
VIEW ANGLE SETUP
INITIALIZE DATA
ORIGIN OFFSET
DOME RESET
P-RESPONSE : OFF
SYSTEM INFORMATION
EXIT(ESC TO EXIT)
P-RESPONSE
The option should be set to OFF when the camera is connected to a DVR. This disables the
response command from the dome in the PELCO-P protocol.
• LANGUAGE SETUP
LANGUAGE SETUP
LANGUAGE
: ENGLISH
SAVE AND EXIT(ESC TO CANCEL)
LANGUAGE
: Select the language you want.
• HOME FUNCTION SETUP
After a dome control menu item has been selected, follow the directions below to set the function.
HOME FUNCTION SETUP
HOME FUNCTION
:
FUNCTION NUMBER :
WATING TIME
:
FUNCTION ENABLE :
SAVE AND EXIT(ESC
HOME FUNCTION
FUNCTION NUMBER
WAITING TIME
FUNCTION ENABLE
NONE
--120 SEC
OFF
TO CANCEL)
: None/ Preset/ Tour/ Pattern/ Auto Scan
: xxx
: 10~240 Seconds
: ON/ OFF
24
The Home function can be set so that the camera automatically goes to Preset, Tour, Pattern,
Auto Scan after the keyboard controller has been idle for a amount of time. For example, if the
Joystick controller is idle for 10 seconds, the camera goes to preset 1.
Follow these steps to program the Home position:
1. Press PRESET + 95 to display the main menu on the monitor.
2. Select Home Function by pushing the Joystick to the right or to the left to scroll through the
None, Tour, Pattern, Auto Scan and Preset functions.
3. Select Function Number by pushing the Joystick down, and push the Joystick to the right
or to the left. The executable function number will scroll. Each function has maximum
numbers. For example, you can have 240 Presets, 8 Tours, 4 Patterns and 8 Auto Scan
options.
4. Select Function Time by pushing the Joystick down. Push the Joystick to the right or to
the left to select from 10 to 240 seconds.
5. Select Function Enable by pushing the Joystick down. Turn the Home Enable ON or OFF
by pushing the Joystick to the right or to the left.
• OSD DISPLAY
DISPLAY SETUP
CAMERA TITLE
: DOMEID
VIEW DIRECTION
: OFF
DOME OSD DISPLAY : ON
AREA DISPLAY
: OFF
SAVE AND EXIT(ESC TO CANCEL)
CAMERA TITLE
VIEW DIRECTION
DOME OSD DISPLAY
AREA DISPLAY
: 8 CHARACTER CAN BE SET
: ON / OFF
: ON / OFF
: ON / OFF
• VIEW DIRECTION
“ON” sets current direction as N(north) and the coordinate angle to 000. “OFF” hides the
directional title. Every 90 degrees of clockwise rotation will change the title to E(East), S(South),
W(West). If using the ON/OFF option frequently, it is recommended that you set “North” as a
Preset. Recall the “North” Preset before enabling the directional title.
• DOME OSD DISPLAY
All display or title will disappear when DOME OSD DISPLAY sets OFF
• AREA DISPLAY
If this option is enabled, the nearest area title will be displayed when the camera is moving
whether by manual operation, Auto Scan, or Pattern. Select ON or OFF by pushing the Joystick
25
to the right or to the left. The Dome camera’s OSD will override this function (Dome camera’s
OSD must be enabled).
• VIEW ANGLE SETUP
VIEW ANGLE SETUP
PANNING RANGE
FLIP
: ON
TILT OVER ANGLE : W/O BUBBLE
SAVE AND EXIT(ESC TO CANCEL)
• PANNING RANGE
When the dome camera is installed near a wall, panning range can be limited by user.
PANNING RANGE SETUP
RIGHT LIMIT : 000.0
LEFT LIMIT : 000.0
ENABLE
: OFF
SWAP RIGHT/LEFT
SAVE AND EXIT(ESC TO CANCEL)
• FLIP
Allows the dome camera to automatically turn 180 degrees when the camera tilts to its lower
position.
When the camera reaches the floor directly above the moving object, it will stop. Release the
Joystick handle instantly and then pull down to run the flip function. The tracking speed will be
the same as previous.
• TILT OVER ANGLE
This option is used to set the limit of the horizontal view angle so that the trim ring or ceiling does
not obstruct the horizontal image when zooming out (wide angle).
ON: In some installations it is desirable for the dome camera to be able to see above the
horizon. When this option is chosen, the dome will tilt up over the horizon(About -10
degrees). When the lens is zoomed out, you can see the ceiling line. But when the lens is
zoomed in, the viewing angle is narrower, and the ceiling line disappears.
Without Bubble: The tilt range of the camera is limited to see the horizon so the picture
shows part of the ceiling line.
With Bubble: The tilt range of the camera is limited to see below the horizon (10 degrees).
Over Angle is not sufficient enough to avoid ceiling obstructions, please adjust Origin Offset
of tilt angle as described below.
26
• INITIALIZE DATA
INITIALIZE DATA
FACTORY DEFAULT
ERASE PROGRAMMED DATA
EXIT(ESC TO EXIT)
Erase all stored data from the Flash-ROM of the selected dome camera. You will be asked to
enter Yes or No. If you intend to erase all data then press the PRESET + 95 key, otherwise
press the PRESET + 96 key to exit without erasing. The erased data includes all stored data
(titles, presets, and tours….) except origin offset.
The offset value is still valid after all data is erased. The offset value can be zeroed only with
default set of Offset origin menu.
• ORIGIN OFFSET
This feature is useful to align a new dome camera exactly the same as the previously installed
dome camera.
Dome camera’s origin set and all data initialize option do not override offset values. Only the
default set option in this menu will set the offset value to zero. This can be used to avoid ceiling
obstructions.
• DOME RESET
This feature is used to re-calibrate the orientation of a selected dome camera. Origin offset value
is not affected by this function. (Offset is still valid after origin set)
• SYSTEM INFORMATION
SYSTEM INFORMATION
CAMERA TYPE
: XXXXXXX
H/W VERSION
: V2.1
ROM VERSION
: V3.6DM
PROTOCOL
: P
BUADRATE
: xxxxBPS
EXIT(ESC TO EXIT)
A Dome camera’s Setup menu provides essential information about the dome camera if service
is required. When you view this screen, you can determine the camera type, ROM version.
The information on this screen cannot be modified.
27
Appendix A — Specifications
Camera (DM/CAM/SD18X/A)
Image Sensor
1/4" Ex-view HAD Color CCD (Sony)
Picture elements
NTSC : 768 x 494 Approx. 380K pixels
PAL : 752 x 582 Approx. 440K pixels
Horizontal Resolution
480 / 470 lines (NTSC / PAL)
Lens
18x optical zoom with auto focus
12x digital zoom
F1.4 to F3.0, f=4.1mm to 73.8mm
View angle
Approx. 48° (WIDE end) to 2.8° (TELE end)
Minimum Illumination
0.7 lux (F1.4,normal shutter speed)
0.1 lux (F1.4,1/4S(NTSC) OR 1/3S(PAL))
0.01 lux (1/4s with IR Cut Filter Removed)
S/N ratio
more than 50dB
Camera (DM/CAM/SD22X/A)
Image Sensor
1/4" Super-HAD Color CCD
Picture elements
NTSC : 768 x 494 Approx. 380K pixels
PAL : 752 x 582 Approx. 440K pixels
Horizontal Resolution
480 / 470 lines (NTSC / PAL)
Lens
22x optical zoom with auto focus
11x digital zoom
F1.6 to F3.6, f=3.9mm to 85.8mm
View angle
Approx. 49.5° (WIDE end) to 2.4° (TELE end)
Minimum Illumination
2.0 lux (F1.6,normal shutter speed)
0.04 lux (F1.6,Low shutter on)
S/N ratio
more than 52dB
WDR
ON/OFF
Camera (DM/CAM/SD26X/A)
Image Sensor
1/4" Ex-view CCD
Picture elements
NTSC : 768 x 494 Approx. 380K pixels
PAL : 752 x 582 Approx. 440K pixels
Horizontal Resolution
480 / 470 lines (NTSC / PAL)
Lens
26x optical zoom with auto focus
12x digital zoom
F1.6 to F3.8, f=3.5mm to 91mm
View angle
Approx. 54.2° (WIDE end) to 2.2° (TELE end)
Minimum Illumination
1.0 lux (normal shutter)
0.07 lux (1/4(3) slow shutter)
0.01 lux (ICR ON, 1/4(3) slow)
S/N ratio
more than 50dB
28
General
Certification
Electrical
Input Voltage
Power Requirement
Power Consumption
Alarm Output
Alarm Input
Control
Access Time
ID (Camera Address)
Mechanical
Dimension
Weight
Pan Angle
Speed
Repeatability
Flip
Autoscan
Preset Position
Tour
Pattern
On-Screen Display
Environment
Operating temperature
Operating humidity
Storage temperature
CE EMC, FCC CLASS A, CSA
18 to 30VAC; 24VAC nominal, 24VDC
24VAC/VDC 1A
Maximum 20W
4 Normal relays 24VDC/1A Max. (selectable NC/NO)
8 Normal dry contact (selectable NC/NO)
RS-485/422 baud rate: 2400~230k bps (default: 9600bps)
0.75 second maximum preset recall time
999
See Figure 10
Approx 1.2 kg
360° continuous rotation
0.1° to 90°/sec. (proportional to zoom)
Preset Speed: 380°/sec
0.2°
Rotate 180° at bottom of tilt
8 auto scan include vector scan
240 positions with camera status (16-character title)
8 tours
Four patterns, 240 second
Displays camera ID and area name on screen
0°C to 50°C (32°F to 122°F)
0 to 90%RH (non-condensing)
-20°C to 60°C (4°F to 140°F)
Specifications are subject to change without notice.
Figure 10 – Dimension
29
Appendix B — Troubleshooting
If problems occur, verify the installation of the camera with the instructions in this manual and
with other operating equipment. Isolate the problem to the specific piece of equipment in the
system and refer to the equipment manual for further information.
Problem
Possible Solution
No video.
Verify that power is connected to all pieces of
equipment in the system.
Verify that the power switches are in the ON position.
Check the video connections
(See Figure 2).
Poor video quality.
Check that the BNC connectors are inserted properly.
Check the voltage level of the dome camera.
Cable for video is shielded.
Dome cameras lose their positions.
Reset the cameras using the Dome configuration
menus.
Check that the dome cameras are inserted properly in
the base.
Check the voltage level of the dome camera.
Camera number does not match the
DVR number.
Check the camera ID and insert the BNC cable into
the proper input of the DVR.
Picture is torn when switching
Check Line Lock setting and adjust phase of L/L
30
Appendix C — Glossary
Alarm Actions
The assigned responses for the dome camera when inputs change from normal to abnormal
states. The dome may run a Preset, Pattern, or have no assigned action for each of the four
dome inputs. The dome may also send alarm states to the host controller for processing. See
also Input and Normal Input State.
Areas
Programmed start and end points of the dome's field of view around its pan axis.
Each area is a part of a circular viewing area that extends around the dome. The areas can be
different sizes. Up to 16 areas can be programmed for the dome.
Automatic Gain Control (AGC)
Allows for the amplification of the video signal in scenes with minimal ambient light. Many lowlight scenes result in picture noise. As gain is increased, the picture noise is also amplified.
When AGC is enabled, the value of the gain setting is based on feedback from the camera.
When AGC is disabled, the camera uses the value set for the manual gain setting. The trade-off
between picture level and noise may be adjusted when AGC is disabled.
On-screen Menu
The text overlay menu system used for setting dome features. The utility is accessed using a
keystroke combination. The utility provides settings for camera functions, zoom, alarms, text
display, and password protection.
Flip
Allows the dome to automatically turn 180 degrees when the camera tilts to its lower limit and
stays in that position for a brief delay. When the dome flips (rotates), the camera starts moving
upward as long as the tilt control is kept in the down position. Once the control is released, the
tilt control returns to its normal operational mode. The flip feature is useful when you need to
track someone who walks directly beneath the dome and continues on the other side.
Home Position
The default position to which the dome camera returns after an assigned period of inactivity
passes. The default position may be a Preset, Tour, Pattern, or No Action.
Input Alarm
A connection point on the dome camera that enables the system to monitor Input Devices. There
are four inputs available for the dome camera.
Input Devices
External devices that provide information about the condition of system components that
connect to the inputs on the dome camera. Typical input devices include door contacts, motion
detectors and smoke detectors.
31
IR Mode
A feature of the camera that permits manual or automatic switching between color and IR
(black-and-white) operation. When IR mode is active, clearer images may be obtained under
low-light conditions.
Line Lock
Allows you to phase lock the video with the AC power line. When line lock is enabled, it prevents
vertical video rolling when switching multiple cameras to a single monitor. If text appears slightly
tinted on color monitors, disabling the line lock may prevent this problem.
Name Information
Relates to the display the dome name, the area where the dome is pointing, the name of the
preset or pattern that is running, and alarm names. The display of each type of name setting can
be enabled or disabled. When the display of camera or area title(name) is enabled, the
information appears on the screen continuously. Preset, tour and pattern titles(names) appear
only while they are active.
Normal Input State
Describes the expected state of a device connected to one of eight dome camera’s inputs. The
normal state may be open or closed. When a device is not in its normal input state, an alarm is
issued.
North Position
User-definable setting that may correspond to magnetic north or some well-known landmark.
Used to approximate the camera dome's pointing direction when Direction Indicators are
enabled.
Slow Shutter
Setting used to improve the quality of video obtained in extreme low-light situations. When the
slow Shutter setting is enabled, low-light information is collected over multiple fields based on
the Shutter Limit setting. As a result, video may appear blurred or choppy in extreme low-light
situations. This setting does not effect camera operation in normal lighting situations. See also
Automatic Gain Control (AGC).
Pattern
A series of pan, tilt, zoom and focus movements from a single programmable dome. Up to 8
patterns may be programmed for the dome camera.
Preset
Programmed video scene, based on a specific pan, tilt, zoom, and focus settings. Up to 240
presets may be programmed for the dome camera.
32
Privacy Zones
Masked areas of the dome camera's viewing area. These masks prevent operators of the
surveillance system from viewing these designated zones. The Privacy Zones move in relation
to the dome camera’s pan/tilt position. In addition, the apparent size of the Privacy Zone adjusts
automatically as the lens zooms in or out. Up to eight Privacy Zones may be established for a
dome camera.
Vector Scan
Move from start point to end point including tilt and zoom simultaneously and linearly.
WDR
Wide Dynamic Range Technology uses two shutter speeds in alternative video fields-high and
normal- every 60th (or 50th) of a second and combines two fields into one progressive scan
frame. It allows every detail to be captured accurately even if one portion of an image is
brilliantly. Whether at the high shutter speed or normal shutter speed, the progressive scan CCD
provides a horizontal resolution of 470 lines. As a result, combined fields yield a frame of highquality images.
White balance
Adjustments in the color hue(red and blue) gains for a camera so that true white appears white
in the image. It is normally compensated for by the automatic gain control. In some lighting
conditions, you may need to manually adjust the red and blue settings for optimal viewing. When
Automatic White Balance is enabled, the camera measures the image and automatically adjusts
the red and blue settings to balance white. When Automatic White Balance is disabled, the
camera uses the values set for the red and blue settings to balance white.
Appendix D — bubble ring
push
bubble ring ass'y
re m ove cam e ra w indow
screw
push
rem ove w indow
assem ble bubble ring ass'y
Figure : Bubble ring
Note: It is recommended to remove camera window for improving picture quality when you use
bubble ring ass’y.
33
Appendix E — Short Cut Key (Pelco protocol) by KBS3 keyboard
Short Cut Key
Function
PRESET +01~ 32
PRESET + 33
Go to Preset
180° Flip (horizontal)
PRESET + 34
Go to 0° (horizontal)
PRESET + 35 ~ 59
Go to Preset
PRESET + 60
Enter Auto Scan setup menu.
PRESET +61~ 68
Run Auto Scan
PRESET + 69
Turn Off Relay 1.
PRESET + 70
Enter Tour setup menu.
PRESET +71~ 78
Run Tour
PRESET + 79
Turn Off Relay 2.
PRESET + 80
Enter Pattern setup menu.
PRESET +81~ 84
PRESET +85~ 88
Run Pattern (or PATROL button + 001~004 )
Turn On Relay.
PRESET + 89
Turn Off Relay 3.
PRESET + 90
Reset Alarm
PRESET + 91
Run Home Function if enabled.
PRESET + 92
Turn Off Relay 4.
PRESET + 93
Enter Preset setup menu.
PRESET + 94
ENTER key
PRESET + 95
MENU key
PRESET + 95
CTRL key in the menu
PRESET + 95
Release CTRL key in the menu
PRESET + 96
ESC key
PRESET + 99
Run AutoPan (endless panning)(or AUTOPAN button)
Dedicated Micros Model KBS3A Keyboard
34