Makita 4330DZ Instruction manual

Cordless Jig Saw
MODEL 433ODWA
MODEL 4330DZ
INSTRUCTION MANUAL
SPECIFICATIONS
Length
of stroke
26 m m
(1")
Max. c u t t i n g capacities
Strokes
Overall
Mild steel
per minute
length
Wood
135mm
I(5-5/16"]
1
I
]!$$T
I
I
Aluminum
2 0 mm
(,3/16,,1
I
2,800
I
280mm
(11")
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
I
1
weight
Net
2'6 kg
( 5 . 7 Ibs)
GENERAL SAFETY RULES
(For All Battery Operated Tools)
WARNING! Read and understand all instructions. Failure
to follow all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you t o loose control.
Electrical Safety
* A battery operated tool w i t h integral batteries or a separate battery pack must
be recharged only w i t h the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk of fire when used with
another battery.
Use battery operated tool only with specifically designated battery pack. Use
of any other batteries may create a risk of fire.
Personal Safety
Stay alert, watch what you are doing, and use common sense when operating
a power tool. Do not use tool while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating power tools may result
in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is in the locked or off position before
inserting battery pack. Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on invites accidents.
Remove adjusting keys or switches before turning the tool on. A wrench or
a key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
2
Tool Use a n d Care
Use clamps or other practical way t o secure and support the workpiece t o a
stable platform. Holding the work by hand or against your body is unstable and
may lead t o loss of control.
Do not force tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
@ D onot use tool if switch does not turn it on or off. A tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in the locked or off
position before making any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of starting the tool
acc identa IIy.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal t o another. Shorting the battery terminals
together may cause sparks, burns, or a fire.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely t o bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
Service
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure
t o follow Maintenance Instructions may create a risk of shock or injury.
Specific Safety Rules
1. Hold tool by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring. Contact with a "live" wire will
also make exposed metal parts of the tool "live" and shock the operator.
2.Be aware that this tool is always in an operating condition because it does
not have t o be plugged into an electrical outlet.
3.Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation.
4. Do not cut hollow pipe.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beneath the workpiece before cutting so that
the blade will not strike the floor, workbench, etc.
7. Hold the tool firmly.
8. Check the blade is not contacting the workpiece before the switch is turned
on.
9. Keep hands away from moving parts.
IO. When cutting through walls, floors or wherever "live" electrical wires may
be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL!
Hold the tool only by the plastic handle t o prevent electric shock if you cut
through a "live" wire.
1 1 . Do not leave the tool running. Operate the tool only when hand-held.
12.Always switch off and wait for the blade t o come t o a complete stop before
removing the blade from the workpiece.
13.Do not touch the blade or the workpiece immediately after operation; they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
SYMBOLS
The followings show the symbols used for tool
v
...................................
volts
min
...................................
minutes
= ...................................
direct current
n,
...................................
no load speed
.../min
...................................
revolutions or reciprocation per minute
5
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER &
BATTERY CARTRIDGE
I. SAVE THESE INSTRUCTIONS - This manual
Length of Cord (Feet)
25
50
100
150
AWG Size of Cord
18
18
18
16
9. Do not operate charger w i t h damaged cord or plug - replace them immediately.
I O . Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it t o a qualified serviceman.
11. Do not disassemble charger or battery cartridge; take it t o a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
6
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OF)
or ABOVE 4OoC (104OF).
2. Do not attempt t o use a step-up transformer, an engine generator or DC power
receptacle.
3. Do not allow anything t o cover or clog the charger vents.
4. Always cover the battery terminals w i t h the battery cover when the battery
cartridge is not used.
5. A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
(1I Do not touch the terminals w i t h any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such
as nails, coins, etc.
(3)Do not expose battery cartridge t o water or rain.
6. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 5OoC (122OF).
7. Do not incinerate the Battery Cartridge even if it is severely damaged or is
completely worn out. The battery cartridge can explode in a fire.
SAVE THESE INSTRUCTIONS.
7
Installing or removing the saw blade
CAUTION:
Always be sure that the tool is switched off and battery removed before installing or
removing the blade.
To install the blade, loosen the screw on
the blade holder.
Loosen
\
Screw
With the blade teeth facing forward, insert
the blade into the blade holder as far as it
will go. Make sure that the back edge of
the blade fits properly in the groove of the
roller. Then firmly tighten the screw to
secure the blade.
CAUTION:
*Always secure the blade firmly. Insufficient securing of the blade may cause blade breakage or serious injury.
*Always clean out the blade holder before installing the blade. Chips or foreign matter on
the blade holder may cause insufficient securing of the blade.
Use a lubricant or cutting oil between the blade and roller when cutting iron or composition board, etc. Failure to do so will shorten the service life of your blade and roller or lead
to potentially dangerous blade breakage.
8
Installing the universal shank jig saw blade
CAUTION:
Always be sure that the tool is switched off and battery removed before installing or
removing the blade.
If the universal blade clamp is used, you
can use blades of other makes which have
a universal shank like the one shown in
the figure, with a blade width of 6.35 mm
( 1/4 " 1.
Insert the blade into the blade holder as far
as it will go. Make sure that the end of the
blade shank reaches the bottom of the
inner slit and tighten the bolt securely with
the hex wrench.
The end of the blade
7
shank should reach the
bottom of the inner slit
Bolt
Selecting the cutting action
This tool can be operated with an orbital or
a straight line cutting action. To change the
cutting action, just turn the lever to the
desired cutting action position. Refer to the
table below to help determine the appropriate cutting action.
Position
Cutting action
0
1
I
Ill
For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
Straight line cutting action
I
II
I
Applications
Small orbit cutting action
I
Large orbit cutting action
I
For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
Medium Orbit cutting action
1
For cutting mild steel, aluminum and hard wood.
1
For fast cutting in wood and plywood.
I
9
Switch action
CAUTION:
Before inserting the battery cartridge into the tool, always check to see that the switch
trigger actuates properly and returns to the "OFF" position when released. Pulling the
trigger hard when the lock off button is not pressed causes switch damage.
To start the tool, simply push the lock off
button then pull the trigger. Release the
trigger to stop.
Lock-off button
Switch trigger
Cutting operation
CAUTION:
Check carefully that the blade is adequately secured in position before inserting the batterv into the tool
Turn the tool on without the blade making
any contact. Rest the base flat on the workpiece and gently move the tool forward
along the previously marked cutting line.
I
Cutting line
CAUTION:
*Always hold the tool with the base flush with the workpiece. Failure to do so may cause
a slanted cutting surface and blade breakage.
*Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may
cause a slanted cutting surface and blade breakage.
10
Bevel cutting
CAUTIO N:
Always remove the battery from the tool before making any adjustments
With the base tilted, you can make bevel
cuts at any angle between 0" and 45" (left
or right). Loosen the bolt on the bottom of
the tool. Move the base so that the bolt is
positioned in the center of the cross-shaped
slot in the base.
Cross-shaped slot
Tilt the base until the desired bevel angle
is obtained. The edge of the motor housing
indicates the bevel angle by graduations.
Then tighten the bolt to secure the base.
Edge of motor housing
k m
Graduations
Flush cutting
Loosen the bolt on the bottom of the tool
and slide the base all the way back. Then
tighten the bolt to secure the base.
I I
Base
I
11
cutouts
Cutouts can be made with either of two methods A or B.
A) Boring a starting hole: For internal cutouts without lead-in cut from an edge,
pre-drill a starting hole more than
12 mm (15/32”) in diameter. Insert the
blade into this hole and hold the tool
firmly against the workpiece to start
your cut.
- /
Starting hole
B) Plunge cutting: You need not bore a starting hole or make a lead-in cut if you carefully
do as follows.
1) Tilt the tool up on the front edge of the base, with the blade point positioned just
above the workpiece surface.
2) Apply firm pressure to the tool so
that the front edge of the base will
not move when you switch on the
tool and gently lower the back end of
the tool slowly.
3) As the blade slices into the workpiece, slowly lower the base of the
tool down onto the workpiece surface.
4) Complete the cut in the normal manner.
Finishing edges
To trim edges or make slight dimensional
adjustments, run the blade lightly along the
cut edges.
12
Metal cutting
Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause
significant blade wear. The underside of the workpiece can be greased instead of using a
coolant.
Anti-splintering device
To reduce the potential for workpiece surface splintering, the anti-splintering device
can be used. Fit it into the base from below
so that it surrounds the sides of the blade.
Plastic base plate (optional accessory)
Use the plastic base plate when cutting
decorative veneers, plastics, etc. It protects
sensitive or delicate surfaces from damage.
To replace the base plate, remove the four
screws with the hex wrench.
Guide rule (rip fence; optional accessory)
When cutting widths of under 150 mm
(5-29/32") repeatedly, use of the guide rule
will assure fast, clean, straight cuts. To
install it, loosen the bolt on the front of the
base. Slip in the guide rule and secure the
bolt.
13
Circular guide (optional accessorv)
Use of the circular guide insures clean,
smooth cutting of circles under 200 mm
(7-7/8") in radius. Insert the pin through the
center hole and secure it with the threaded
knob. Move the base of the tool fully forward. Then install the circular guide on the
base in the same manner, as the guide rule
(rip fence).
Vacuum head (optional accessory)
The vacuum head is recommended to perform clean cutting operations. Install the
plastic cover on the tool by fitting it into the
notches in the tool.
Fit into notches
Base
\
To attach the vacuum head on the tool,
insert the hook of the vacuum head into
the hole in the base. The vacuum head can
be installed on either left or right side of
the base. Then connect a Makita vacuum
cleaner to the vacuum head.
I
14
-
Hex wrench
Plastic cover
Hook of vacuum head
I
Plastic cover
L-.-Hose of
vacuum head
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
-
ReDlacina carbon brushes
I
Remove and check the carbon brushes
regularly. Replace when they wear down to
the limit mark. Keep the carbon brushes
clean and free to slip in the holders. Both
carbon brushes should be replaced a t
the same time. Use only identical carbon
brushes.
L
Limit mark
Use a screwdriver to remove the brush
holder caps. Take out the worn carbon
brushes, insert the new ones and secure
the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should
be performed by Makita Authorized or Factory Service Centers, always using Makita
replacement parts.
Recycling the Battery
The only way to dispose of a Makita battery is
to recycle it. The law prohibits any other
method of disposal.
1
1
Ni-Cd
To recycle the battery:
1. Remove the battery from the tool.
2. a). Take the battery to your nearest Makita Factory Service Center
or
b). Take the battery to your nearest Makita Authorized Service Center or
Distributor that has been designated as a Makita battery recycling location.
Call your nearest Makita Service Center or Distributor to determine the location
that provides Makita battery recycling. See your local Yellow Pages under
"Tools-Electric':
15
ACCESSORIES
CAUTION:
These accessories or attachments are recommended for use with your Makita tool specified in this
manual. The use of any other accessories or attachments might present a risk of injury t o persons.
The accessories or attachments should be used only in the proper and intended manner.
An exception: Universal shank jig saw blades with a thickness of 1 m m - 1.25 m m (1/32" - 3/64")
and a length of 58 m m - 82 m m (2-9/32" - 3-7/32").
Plastic base plate
Anti-splintering device
Part No. 41 5537-8
Part No. 415524-7
Hex wrench 3
Plastic cover
Part No. 783201-2
Part No. 415525-5
r
Circular guide assembly
Guide rule
Part No. 123030-5
Part No.164113-2
1
Vacuum head
Part No.192108-5
Jia saw blade (Packed 5 each)
type
Hose 19-2.5
Part No. 192418-0
Teeth per
inch
792428-3
24
Effective cutting
blade length
65 mm (2-W')
Part No,
1
1
1
1
1 1 I 1
No. 51
I
I
No. 58
No. 59
I 792429-1 I
1792430-6 I
8
I
80 mm (3-1/8")
8
I
80"
(3-1/8")
I
I I No. E-21 I 792472-0 I
I No. 6-22 17924738 I
No. 6-23 1792474-6
;
80 mm (3-1/8")
No. 8-24
7924754
80 mm (3-1/8")
NO.8-25
792476-2
50mm(2")
50 mm (2")
NO.B-16
792468-1
80 mm (3-1/8")
792477-0
NO.B-26
792478-8
No. 6-27
No. BR-13 792727-3
NO.6-17
792469-9
70 mm (2-3/4")
No. B-16L
No. 8-14 1792466-5
NO.6-1 5 792467-3
(Note)
Refer to the next page for "Application" of each blade.
16
I
65 mm (2-1/2")
12
I
75 mm (3")
I
;;
I
50 mm (2")
I
24
50mm(2")
50 mm (2")
75 mm (3")
I
I 792726-5 I
24
9
6
70 mm (2-3/4")
50 mm (2")
64 mm (2-1/2")
1
I 150 mm (5-7/8")
Jia saw blade
Application
Blade Type
Wood & olvwood
No. 51
-
No, 58
4 - 60 mm thick
6 / 3 2 ' ' - 2-3/8"1
1
Plastics
I
I
Aluminum
I
Mild Steel
Feature
1.5 - 3 mm thick
11/16'' - l/8"l
1 - 6 mm thick
13/64" - 1/4"l
1 - 3 mm thick
13/64" - 1B"I
4 - 60 mm thick
15/32" - 2-3/87
-
-
For fast cutting.
For fast finish work
Also ideal for cutting
stainless steel.
~~
No 59
4 - 30 mm thick
15/32" - 1-1/8"1
4 - 30 mm thick
15/32'' - 1-1/87
-
-
NO
3 - 60 mm thick
l1/8" - 2-3B"l
3 - 60 mm thick
IlB"- 2-3B'l
-
-
I
I
I
I
No,
No,
No
No,
No
N'
'-16
No '-17
No
I
I
I
I
NO.
No. 6-21
I
NO 6-24
No. 8-27
5 - 6 0 mmthick
(13/64" - 2-3B"l
4 -60 mm thick
15/32" - 2-3/8"l
2 - 30 mm thick
15/64" - 1-1B"I
3 - 30 mm thick
(1/8" - 1-1/8")
5 - 60 mm thick
(13/64" - 2-3/8"1
5 -60 mm thick
113/64"-2-3/8"l
2 -30 mm thick
15/64" - 1-1B")
3 - 30 mm thick
11/8" - 1-1B"l
-
I
I
I
I
I
I
I
I
I
-
No. 6-22
No 6-23
3 - 30 mm thick
(1"' - 1-1B")
1
I
I
-
I
3 - 50 mm thick
11B' - 2")
5 - 6 0 mm thick
l13/64" 2-3/8')
-
4 - 60 mm thick
15/32" - 2-3/8'1
2 - 30 mm thick
15/64'' - 1-1/8"1
3 - 30 mm thick
(1/8" - 1-1/8"1
5 - 60 mm thick
l13/64" - 2-3/8')'
5 - 60 mm thick
tl3/64"-2-3/87'
2-30,mmthickS
15/64 - 1-1/8")
I - I I
I
I
I
I - I I
I
I
I
3 - 30 mm thick
11/8" - l-lB")
3 - 6 mm thick
11/8" - 1/4"l
-
-
-
1
-
3-1Ommthick
11/8' - 3/8"l
I
1 - 6 mm thick
13/64'' 1/4")
-
3 - 10 mm thick
11B" - 3B"l
1
I
Forroughing-in work
Ideal for cuning in thin
materials
I
I
I
-
For fast cutting
Ideal for scroll cutting.
Ideal for scrollcutting.
Cuts on down stroke.
Splinter-free on finish side.
-
I
For fast finish work.
Ideal for cutting in thin
materials
-
I
I
I
For fast finish work.
I
I
1 - 3 mm thick
(3/64" - 1B")
3 - 6 mm thick
11B" - 1/4")
For finish work. especially
in plastics
Also ideal for cutting
stainless Steel
Also ideal for cutting
stainless steel
-
-
I
1.5-3mmthickHI
11/16" - 1/8,,1
1-6mmthick
13/64,,- 1/4,n)
l
No' 6-16L
-
-
3-55mmthickHI
11B" - 2-1/8"1
1.5 - 3 mm thick
(1/16" - 1/8")
-
I
I
I
For fast finish work,
especially in plywood
5 - 110 mm thick
l13/64" -4-5/16"1
5 - 110 mm thick
l13/64" -4-5/16"1
-
I
1
&
;&myc:;F
-
1
Splinter-free cuts in wood,
requiring no sanding.
Ideal for cuning thick
materials.
17
Nov-19-'98
US
CORDLESS JIG SAW
Model 43301)
Note: The switch and other part configurations
may differ from country to country.
18
MODEL 4330D
'i\M
1
2
$zD
1
Nor-19-'98
1
1
4
6
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
1
1
1
1
1
Switch Button
Compression Spring 4
Housing Set (With Item 511
Tapping Screw 4x18
Tapping Screw 4 x 3 0
Pan Head Screw M4x25
Switch
Switch Lever
Battery Holder
Holder
1
Gear Housing Cover Complete
4
1
2
P," 4
26
27
28
29
30
31
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
-
SD
DESCRIPTION
3
Tapping Screw 4x18
Compression Spring 4
Holder
Stop Ring E-3
Slider
Countersunk Head Screw M4x10
Thrust Plate
Retainer Complete
Name Plate
Rod
Hex Socket Screw M6x8
Slide Plate
Packing
Retaining Ring 5 - 8
Needle Bearing 607
Hex Socket Head Bolt M4x18
Crank Complete
Flat Washer 26
Flat Washer 6
US
DESCRIPTION
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
59
1
1
60
61
4
1
Balance Plate
Pin 6
Balance Plate
Flat Washer 6
Flat Washer 6
Pin 6
Push Plate
Flat Washer 26
Needle Bearing 810
Flat Washer 5
P," 5
Helical Gear 51
Needle Bearing 810
Flat Washer 8
P," 8
Tapping Screw ST 4x8
Motor Bracket
Countersunk Head Screw M4x10
DC Motor IWith Spur Gear)
Housing Set IWith Item 31
Lever 17
Compression Spring 4
Steel Ball 4
Stop Ring IEXTI E-5
Base
Clamp Plate
Base Plate
Hex Socket Head Bolt M4x16
Hex Socket CS Head Bolt M5x8
Safety Wlre
Note The switch and other part specifications may differ from country t o country
19
MAKITA LIMITEDONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, retum the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
This Warranty does not apply where:
repairs have been made or attempted by others:
repairs are required because of normal wear and tear:
The tool has been abused, misused or improperly maintained;
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE O F THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM O F THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING lMPLIED
WARRANTIES O F “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-YEAR TERM O F THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or Limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
Makita Corporation of America
2650 Buford Hwy., Buford, GA 3051 8
MCW 1/99
884234-063
PRINTED IN USA
1999-01-4D