Bryant T2-NHP Owner`s manual

T2--NHP, T2--NAC
Legacyt Series
Non--Programmable Thermostat
Owner’s Manual
YOU WILL LOVE THIS THERMOSTAT.
This Legacyt non--programmable thermostat is an easy
to use model that provides the most sought--after features
for keeping your home comfortable. And with a slim
profile, it is designed to be as smart – and smart--looking
– as any of the other electronics in your home. Let this
manual show you how easy it is to enjoy the newest experience in home comfort.
Designed and Assembled in the U.S.A.
NOTE: Read the entire instruction manual before starting the installation.
1
TABLE OF CONTENTS
BUTTON IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ON--SCREEN INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
OPERATING THE THERMOSTAT
Setting the temperatures for heating and cooling . . . . . . . . . . . . . . . . . . . . 8
Using the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using emergency heat (heat pump systems only) . . . . . . . . . . . . . . . . . . 10
Installing or replacing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the thermostat to turn the heating and cooling system off . . . . . . 14
Auto changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ADVANCED OPTIONS
Advanced options display codes chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing from Fahrenheit to Celsius . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Turning on the continuous backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Keypad lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Unlocking the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2
TABLE OF CONTENTS
WHAT IF . . .
The battery icon is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
“Aux heat on” is displayed (heat pump systems only) . . . . . . . . . . . . . . 20
“Em heat” is displayed (heat pump systems only) . . . . . . . . . . . . . . . . . . 20
There is a power outage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
You get a system error message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COMMON TERMS AND WHERE TO FIND THEM
Auto changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auxiliary heat (heat pump systems only) . . . . . . . . . . . . . . . . . . . . . . . . . 22
Backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Emergency heat (heat pump systems only) . . . . . . . . . . . . . . . . . . . . . . . . 22
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3
BUTTON IDENTIFICATION
b
c
a
d
4
BUTTON IDENTIFICATION
a.
FAN
Selects whether the fan operates continuously (on) or only when
needed for heating or cooling (auto)
b.
MODE
Selects whether thermostat is set for heating, cooling, emergency
heat (heat pump system only), auto (heat and cool as needed), or off
c.
UP
Increases the temperature or adjusts the screen selection up when
setting advanced features
d.
DOWN
Decreases the temperature or adjusts the screen selection down
when setting advanced features
5
ON--SCREEN INDICATORS
5
4
3
2
1
off
Em
heat
aux
heat
on
fan
auto
fan
on
F
C
6
7
actual temp
cool
on2
set at
6
8
9
10
ON--SCREEN INDICATORS
1. Fan mode – on or auto
2. System is in auxiliary (supplemental) mode
3. Current temperature
4. Thermostat mode is either off or using emergency heat
5. Fahrenheit
6. Keypad is locked (no padlock means unlocked)
7. Celsius
8. Battery strength indicator
9. Selected cooling set point; “on” indicates system is in cooling mode
10. Second stage of cooling is active
7
OPERATING THE THERMOSTAT
Setting the temperatures for heating and cooling
Your thermostat is installed with the heating set at 68° F and the cooling set at 72° F.
You can use these or change them so your home is as warm or as cool as you would
like it to be. These steps will hold the temperature where you set it.
1. To change the heating temperature, press the mode button on the left until the screen says heat.
2. Press the up or down button located on the right side of
the display until you reach the desired temperature.
3. To change the cooling temperature, press the mode button on the left until the screen says cool.
4. 4. Press the up or down button located on the right side of the display until
you reach the desired temperature.
8
OPERATING THE THERMOSTAT
Using the fan
When the fan is on, it helps distribute air throughout your home for a more even
temperature in all spaces. You can set the thermostat so that the fan runs only
during your heating and cooling cycles (auto mode) or to run continuously.
The thermostat is set at the factory to run automatically as needed. Here’s how to
change the setting so it runs continuously.
1. Press the fan button on the left. The display message will change from auto
fan to fan on.
2. To return the fan to auto mode, press the fan button
again. You will see fan auto on the display.
9
OPERATING THE THERMOSTAT
Using emergency heat (heat pump systems only)
Emergency heat is useful when the automatic auxiliary heat system can’t keep up
with demand. (Systems with heat pumps use “auxiliary heat” when it’s too cold
outside for the heat pump to heat the house without help. The display indicator for
this is aux heat on.)
If the heat pump compressor that works with auxiliary heat fails, or if the heat pump
isn’t working at all, you can turn on the emergency heat for that extra help. (You’ll
know there’s a problem if the house can’t seem to get warm when it’s very cold
outside.) You want to avoid using emergency heat, though, because it’s the most
expensive option. And, of course, if you suspect a problem with your heat pump,
call your heating and cooling dealer immediately.
Here’s how to set your thermostat to use emergency heat.
1. Press the mode button repeatedly until you see Em heat
in the upper left of the display.
2. To turn off emergency heat, press the mode button again
to select heat, cool or auto.
10
OPERATING THE THERMOSTAT
Installing or replacing the batteries
You can install batteries in your thermostat so that if the power goes out, the display
will still show the indoor temperature.
In some situations, batteries are also the power source. Then, two AA batteries
should last about one year. When the batteries have lost about one-- third of their
power, a battery icon appears on the display. Two-- thirds of it will be black. As the
batteries get weaker, the icon goes down to one black bar and then none. When the
icon is empty, you will begin to lose thermostat functions when it is battery
powered. When the batteries are completely dead, you won’t be able to use the
thermostat.
When using batteries for power, we recommend that you replace the batteries at the
one bar level with two AA alkaline batteries. They’re in the back of the thermostat,
so you’ll have to remove it from the wall.
Here’s how to both install and replace batteries.
1. Locate the latch at the top of the thermostat. It’s at the
center of the top rim.
11
OPERATING THE THERMOSTAT
2. Press it down. This will disconnect the thermostat from the
top of the wall plate.
3. Remove the thermostat from the wall bracket completely by bringing it slightly toward you and lifting it up
and off the lip on the lower edge of the wall bracket.
4. Set the thermostat face down on a flat surface. You will
see the batteries in the lower right corner.
5. Remove and discard the old batteries.
6. Install new batteries by matching the “plus” and “minus”
ends of the batteries with the “plus” and “minus” indicators you’ll see outside the two white battery shapes in the
space where the batteries sit.
7. Snap the batteries into place.
8. Put the thermostat back on the wall bracket by lining up
the slot on the bottom edge of the back of the thermostat
with the lip on the wall bracket. You will feel the slot fit
over the lip.
12
OPERATING THE THERMOSTAT
9. With the bottom of the thermostat attached to the bottom
of the wall bracket, bring the thermostat back to the
wall. Line up the latch at the top of the thermostat with
the corresponding lip on the wall bracket.
10. Lightly push the thermostat toward the wall. When the
latch and lip are lined up properly, you will hear the
thermostat snap into place.
11. Close the door.
13
OPERATING THE THERMOSTAT
Using the thermostat to turn the heating and cooling system off
To use the thermostat to turn the heating and cooling system
off, press the mode button on the left repeatedly until the
display shows off in the upper left.
Auto changeover
The thermostat uses one of five modes: heat, cool, Em heat (heat pump version
only), auto, and off. When the mode selection is auto, the thermostat is in auto
changeover mode. This allows the system to switch from heating to cooling – or
from cooling to heating – to maintain the temperatures you’ve set. It does this
automatically.
14
ADVANCED OPTIONS
Advanced options display codes chart
You can customize a few features of your thermostat. This chart shows which
features you can change and the codes associated with them. The codes will be
shown on the display when you follow the instructions.
Feature
Configuration
Code
Change Indication
Fahrenheit to Celsius
U1
F or C
backlighting
U2
On or Of
keypad lockout
U3
Of, On, padlock
15
ADVANCED OPTIONS
Changing from Fahrenheit to Celsius
Your thermostat is preset to display the temperature in degrees
Fahrenheit. You can change this to Celsius.
1. Press and hold the mode button for about three seconds.
The display will show U1 and the letter F in the center.
2. Press the up or down button on the right to change it
from F (Fahrenheit) to C (Celsius).
3. Press the fan button on the left to exit this screen.
16
ADVANCED OPTIONS
Turning on the continuous backlighting
The thermostat display lights up for a few seconds after you press any button. This
is backlighting. It will go dark after a few seconds.
If the thermostat is powered by electricity, it is possible to have a constant low level
amount of backlighting until you press any button, which increases the lighting
temporarily. Here’s how to turn on the constant backlight when your thermostat is
powered by electricity.
1. Press and hold the mode button for about three seconds.
The display will show U1 and the letter F in the center.
2. Press the mode button twice. The display will show U2
and Off.
3. Press the up or down button on the right to change it
from Off to On.
4. Press the fan button on the left to exit this screen.
17
ADVANCED OPTIONS
Keypad lockout
The keypad lockout feature lets you “lock” the thermostat so nobody can change
the temperature – or make any other changes – by pressing buttons. Keypad
lockout is not activated when the thermostat is installed. Here’s how to activate it.
1. Press and hold the mode button for about three
seconds. The display will show U1 and the letter F in
the center.
2. Press the mode button until the display shows U3 and
Of.
3. Press the up or down button on the right to change it
from Of to On. You will also see a padlock, which indicates the keypad is locked.
4. Press the fan button on the left to exit this screen.
18
ADVANCED OPTIONS
Unlocking the keypad
Here’s how to temporarily unlock the keypad.
1. Press and hold the up and down buttons on the right
simultaneously for about five seconds.
2. The padlock icon will disappear. This means the keypad is unlocked and
can be used. The keypad will revert back to the locked state after you’ve
stopped pushing buttons for two minutes.
19
WHAT IF . . .
The battery icon is displayed
The battery icon appears on the display only when the battery starts to lose power.
Replace it when one-- third of the icon is black. If your thermostat is battery
powered and you wait until the icon is just a silhouette with no black bars, you will
slowly lose thermostat functions until it doesn’t work at all.
“Aux heat on” is displayed (heat pump systems only)
Aux heat on is auxiliary heat. It applies only to the heat pump version. If it
is on, you will see aux heat on. When it is displayed, it means the system
has determined that it’s too cold outside for your heat pump to heat the
house without help, so it’s getting help from the electric heaters. This happens automatically.
“Em heat” is displayed (heat pump systems only)
Em heat is the display term for emergency heat and applies only to the heat pump
version. You have to turn on emergency heat manually – it doesn’t happen
automatically – so if you see Em heat on the display, it means somebody has
turned it on.
20
WHAT IF . . .
There is a power outage
If you lose electricity and have batteries installed, the thermostat will continue to
display the indoor temperature because it has a battery backup power source. This
means that even though your heating and cooling system doesn’t work, you will
still be able to monitor your home’s temperature.
You get a system error message
Here are the possible system error messages and what they mean:
----
The room air sensor reports that the room air temperature is above
150° or below --50°.
E4
The memory has failed and the thermostat will return to the default factory
settings. Call your heating and cooling dealer.
21
COMMON TERMS AND WHERE TO FIND THEM
Auto changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14
This feature automatically switches your system from heating to cooling – or from
cooling to heating – whenever necessary.
Auxiliary heat (heat pump systems only) . . . . . . . . . . . . . . . . . . . . page 10
Most heat pump systems can’t heat a home sufficiently when it gets very cold
outside so they use a supplemental heating source called auxiliary heat. The system
knows when to use this help and does so automatically. If it’s using auxiliary heat,
the display will show aux heat on. You have no control over the auxiliary heat
function.
Backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Backlighting illuminates your display when you push a button.
Emergency heat (heat pump systems only) . . . . . . . . . . . . . . . . . . page 10
You can manually set the thermostat to use emergency heat but it is the most
expensive option. If it’s using emergency heat, the display will show Em heat.
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14
This term refers to the type of operation your system is performing. The options are
heat, cool, emergency heat, auto, and off.
22
THERMOSTAT LIMITED WARRANTY
Bryant Heating & Cooling Systems
Limited Warranty for Thermostats
FOR WARRANTY SERVICE OR REPAIR:
Contact the installer or a Bryant dealer. You may be able to find the installer’s name on the
equipment or in your Owner’s Packet. You can also find a Bryant dealer online at
www.bryant.com
For help, contact: Bryant Heating & Cooling Systems, Consumer Relations, P.O. Box 4808,
Syracuse, New York 13221, Phone 1--800--428--4326
PRODUCT REGISTRATION: You can register your product online at www.bryant.com.
Model Number_______________________
Serial Number_______________________
Date of Installation____________________
Installed by_________________________
Name of Owner_______________________
Address of Installation_________________
Bryant Heating & Cooling Systems (hereinafter “Company”) warrants this product against
failure due to defect in materials or workmanship under normal use and maintenance as
follows. All warranty periods begin on the date of original installation. If a part fails due to
defect during the applicable warranty period Company will provide a new or remanufactured
part, at Company’s option, to replace the failed defective part at no charge for the part.
Alternatively, and at its option, the Company will provide a credit in the amount of the then
factory selling price for a new equivalent part toward the retail purchase price of a new
Company product. Except as otherwise stated herein, those are Company’s exclusive
obligations under this warranty for a product failure. This limited warranty is subject to all
provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of
this document.
23
THERMOSTAT LIMITED WARRANTY
OWNER--OCCUPIED, RESIDENTIAL APPLICATIONS
This warranty is to the original purchasing owner and is transferable only to the extent and as
stated in the Warranty Conditions and below. The warranty period in years, depending on the
part and the claimant, is as shown in the chart below.
Limited Warranty (Years)
Original Owner
Subsequent Owner
10* (or 5)
5
Product
T6, T2, T1 Thermostats***
*
If properly registered within 90 days, otherwise 5 years (except in California and Quebec
and other jurisdictions that prohibit warranty benefits conditioned on registration, registration is not required to obtain longer warranty periods). See Warranty Conditions below.
***Applies only to Thermostats. Active electronic finished good accessories, such as the optional ExP module, have different warranty terms. See product for details.
OTHER RESIDENTIAL APPLICATIONS (Apartments, Rental Properties, etc.)
The warranty period is five (5) years. The warranty is to the original owner only and is not
transferable.
OTHER APPLICATIONS
The warranty is one (1) year on all such applications. The warranty is to the original owner
only and is not transferable.
LEGAL REMEDIES: The owner must notify the Company in writing, by certified or
registered letter to Bryant Heating & Cooling Systems, Warranty Claims, P.O. Box 4808,
Syracuse, New York 13221, of any defect or complaint with the product, stating the defect or
complaint and a specific request for repair, replacement, or other correction of the product
under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
24
THERMOSTAT LIMITED WARRANTY
WARRANTY CONDITIONS:
1. To obtain the longer warranty periods as shown in the table under original owner, for
the original purchaser, the product must be properly registered at www.bryant.com
within ninety (90) days of original installation. In jurisdictions where warranty terms
conditioned on registration are prohibited by law, registration is not required and the
longer warranty period shown will be apply.
2. Where a product is installed in a newly constructed home, the date of installation is the
date the homeowner purchased the home from the builder.
3. If the date of original installation cannot be verified, then the warranty period begins
ninety (90) days from the date of product manufacture (as indicated by the model and
serial number). Proof of purchase may be required at time of service.
4. The remainder of the first five years of warranty is freely transferable without
registration.
5. Product must be installed properly and by a licensed HVAC technician.
6. The warranty applies only to products remaining in their original installation location.
7. Installation, use, care, and maintenance must be normal and in accordance with
instructions contained in the Installation Instructions, Owner’s Manual and Company’s
service information.
8. Defective parts must be returned to the distributor through a registered servicing
dealer for credit.
LIMITATIONS OF WARRANTIES: ALL IMPLIED WARRANTIES AND/OR
CONDITIONS (INCLUDING IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE) ARE
LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES OR
25
THERMOSTAT LIMITED WARRANTY
PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY OR CONDITION LASTS, SO THE ABOVE MAY NOT APPLY TO YOU.
THE EXPRESS WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND
MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR,
DEALER, OR OTHER PERSON, WHATSOEVER.
THIS WARRANTY DOES NOT COVER:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping,
servicing or handling of either defective parts, or replacement parts, or new units.
2. Any product purchased over the Internet.
3. Normal maintenance as outlined in the installation and servicing instructions or Owner’s
Manual, including filter cleaning and/or replacement and lubrication.
4. Failure, damage or repairs from faulty installation, misapplication, abuse, improper
servicing, unauthorized alteration or improper operation.
5. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages
due to the inadequacy or interruption of electrical service.
6. Failure or damage due to floods, winds, fires, lightning, accidents, corrosive environments
(rust, etc) or other conditions beyond the control of Company.
7. Parts not supplied or designated by Company, or damages resulting from their use.
8. Products installed outside the U.S.A. or its territories and Canada.
9. Electricity or fuel costs, or increases in electricity or fuel costs from any reason
whatsoever, including additional or unusual use of supplemental electric heat.
10. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
11. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR
COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some states or
provinces do not allow the exclusion of incidental or consequential damages, so the above
limitation may not apply to you.
This Warranty gives you specific legal rights, and you may also have other rights which vary
from state to state or province to province.
39004DP479
08/2011
26
NOTES PAGE
27
NOTES PAGE
28
Copyright 2012 Bryant Heating & Cooling Systems, 7310 W. Morris St. Indianapolis, IN 46231
Catalog No: OM--- T2NHP--- 05BR
Replaces: OM--- T2NHP--- 04BR
Edition Date: 05/12
Manufacturer reserves the right to change, at any time, specifications and designs without notice
and without obligations.