Samsung TB14A53X/RAD Specifications

Television Video Cassette Recorder
Chassis :
Model :
Television Video Cassette Recorder
C15C ( VER.1, TS-10 )
TB14A53X/RAD
CONTENTS
1. Precautions
2. Specifications
3. Disassembly and Reassembly
4. Alignment and Adjustment (Mechanical)
5. Alignment and Adjustment (Electrical)
6. Troubleshooting
7. Exploded View and Parts List
8. Electrical Parts List
9. Block Diagram
10. Wiring Diagram
11. Schematic Diagrams
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective
devices are replaced. Restore any missing
protective shields.
2. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control knobs
and compartment covers.
3. Make sure that there are no cabinet openings
through which people—particularly
children—might insert fingers and contact
dangerous voltages. Such openings include
the spacing between the picture tube and the
cabinet mask, excessively wide cabinet
ventilation slots, and improperly fitted back
covers.
If the measured resistance is less than 1.0
megohm or greater than 5.2 megohms, an
abnormality exists that must be corrected
before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):
Warning: Do not use an isolation
transformer during this test. Use a leakagecurrent tester or a metering system that
complies with American National Standards
Institute (ANIS C101.1, Leakage Current for
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug
the AC line cord directly into the power
outlet. With the unit’s AC switch first in the
ON position and then OFF, measure the
current between a known earth ground (metal
water pipe, conduit, etc.) and all exposed
metal parts, including: antennas, handle
brackets, metal cabinets, screwheads and
control shafts. The current measured should
not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the
test.
Samsung Electronics
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
TEST ALL
EXPOSED METAL
SURFACES
3-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
Fig. 1-1 AC Leakage Test
6. Antenna Cold Check:
With the unit’s AC plug disconnected from the
AC source, connect an electrical jumper across
the two AC prongs. Connect one lead of the
ohmmeter to an AC prong. Connect the other
lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to prohibit X-ray emissions. To ensure continued
X-ray protection, replace the picture tube only
with one that is the same type as the original.
Carefully reinstall the picture tube shields and
mounting hardware; these also provide X-ray
protection.
8. High Voltage Limits:
High voltage must be measured each time servicing is done on the B+, horizontal deflection
or high voltage circuits. Correct operation of
the X-ray protection circuits must be
reconfirmed whenever they are serviced.
(X-ray protection circuits also may be called
“horizontal disable” or “hold-down”.)
Heed the high voltage limits. These include
the X–ray Protection Specifications Label, and
the Product Safety and X-ray Warning Note on
the service data schematic.
1-1
2. Specifications
The descriptions and characteristics given in this booklet are given for information purposes only and
are subject to modification without notice.
TELEVISION PART
Colour systems
TV standards
Number of channels
Reception range/cable TV
Aerial input
VCR PART
Format
Heads
Luminance
Colour
FF/REW time
Wow and flutter (WTD)
Frequency response
GENERAL
Power supply
Consumption
Audio output power
Number of loudspeakers
Tube size
Tube type
Sockets
Dimensions (W x D x H)
Weight
Operating temperature
Relative humidity
Samsung Electronics
PAL(option) / SECAM(option) (UK;PAL)
L/L’(option), B/G(option), D/K(option) (UK;I)
100 programmes
Hyperband/interband tuner
75 Ohms, coaxial cable
VHS standard
(PAL / SECAM(option) / MESECAM(option) / NTSC in playback only)
Video: 2 rotary heads, LP(option), 4 Heads(option)
Audio/Control: 1 stationary head (linear)
Erase: 1 full track erase head
System Video
Normal CCIR
System Audio
Mono / NICAM&A2-STEREO
FM azimuth recording
Down converted subcarrier phase shifted direct recording
Less than 100 seconds in FF with E-120
0.4% maximum (SP)
100 Hz - 8 KHz
220-240V~, 50Hz (110-260V~, 50/60Hz; option)
14” (60W)
20”/21” (90W)
14” (1.5W)
20” (3W)
21” (1.5Watts x 2)
14”/20” (1)
21” (2)
14” (37cm/34cmV)
20” (51cm/48cmV)
21” (55cm/51cmV)
BLACK MATRIX
1 full RGB SCART on the rear
1 RCA input (audio and video) on the front
Earphones output (3.5 mm mini-jack)
1 aerial/cable TV coaxial input
14” (368.5 x 388 x 381)
20” (488 x 477 x 488)
21” (520 x 495 x 508)
14” (11.7 kg)
20” (20.4 kg)
21” (23.2 kg)
5°C - 40°C (41°F - 104°F)
10% - 75%
2-1
Disassembly and Reassembly
3. Disassembly and Reassembly
3-1 Disassembly
3-1-1 Back Cover Removal
1. Remove the screws located on the side of the back cover.
Samsung Electronics
3-1
4. Disassembly and Reassembly
4-1 Deck Parts Locations
4-1-1 Top View
Œ
ˇ
¨
ˆ
´
Ø
Fig. 4-1 Top parts Location-1
Œ
´
ˇ
¨
ˆ
Ø
GEAR FL CAM
MOTOR LOADING ASS’Y
LEVER FL ARM ASS’Y
HOLDER FL CASSETTE ASS’Y
LEVER FL DOOR
SLIDER FL DRIVE
Samsung Electronics
4-1
Troubleshooting
6. Troubleshooting
6-1 No Power (No Picture on)
Check
both terminal voltages
of C820 (125V)
Yes
No
Check both
terminal voltages of
C807 (280~300V).
Yes
Is Q801 Pin 3
19~22V?
Yes
Check/Replace
T801.
No
Check D801~804
F801,Q801.
No
No
Check whether
each power line
is short or open.
No
Check IC801
Check
Voltage of 5V, 6V, 8V,
13V power line..
Yes
Is IC901
Pin 64 Voltage 5V?
Yes
No
Check/Replace
IC901.
No
Check/Replace
IC902.
Check H.V SYNC on
IC901 Pins 1, 2
Yes
Check
IC901 Pin 3 is High
when power is On.
Yes
Check the voltage
of TU001.
Samsung Electronics
6-1
Exploded View & Parts List
7. Exploded View & Parts List
7-1 TB14A53X/RAD
Samsung Electronics
No
Code No
Description;Specification
Q’ty
1
AA91-00184D
ASSY CABINET FRONT;-,14A5 MASTER,BK708P
1
AA64-31339P
CABINET FRONT;14A5,C5,BK708P HITRON EL,H
1
1-1
AA64-70127F
BADGE-BRAND;AL,SAMSUNG,SILVER,L40,R800,N
1
1-2
AA96-00149A
ASSY-SPEAKER;-,-,16 OHM,2.5W,3001-001015
1
1-3
AA95-00630B
ASSY-PCB,A/V;-,14/20/21,C15C,PAL,-,MO
1
1-4
6003-000333
SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
2
1-5
AA64-00018A
WINDOW-REMOCON;-,TVN-502V,-,PC,VIOLET,-,
1
1-6
AA64-00012A
INDICATOR-LED;-,TVN-502V,-,PC,-,CLEAR,-
1
1-7
6003-000333
SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
2
1-8
AA64-00051E
PANEL CONTROL;14A5 MAST,HIPS,-,V0,BLK,-,
1
2
AA03-10002N
CRT-COLOR;-,A34KQV42X,-300MG,14,90DEG,5
1
2-1
AA65-30016A
CLAMP-D,COIL;-,NYLON-66,V0,-,NTR,DADH-36
2
2-2
AA60-10050R
SCREW-ASSY;-,SWRCH18A,M5,L31.5,HH,+,WC,-
4
2-3
3704-000103
SOCKET-CRT;10P,22.5,14.3,SN,ISMS01S/BK
1
3
AA64-31340C
CABINET-BACK;-,14A5,C5,SEA ,HIPS,V0,BLK
1
3-1
6002-000514
SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWR
4
3-2
AA42-00003A
ANT ROD;-,3S,720mm,ABS,UL/CSA,-
1
4
AA96-20124A
ASSY-POWER,CORD;-,EP2/YES(AU),H/C250,KJP
1
Remark
AV+CF
IND+CF
CRT
CB+CF
7-1
Electrical Parts List
8. Electrical Parts List
8-1 TB14A53X/RAD
Loc. No.
Code No.
Description ; Specification
Remark
ASSY PCB MAIN(OPT)
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
1
*
AA94-02669C ASSY PCB MAIN(OPT);TB14A53X/RAD,C15C,NEW
..2
..2
..2
..2
..2
..2
..2
...3
...3
...3
...3
...3
..2
..2
...3
...3
...3
...3
...3
...3
..2
...3
...3
...3
...3
..2
...3
...3
...3
..2
..2
..2
..2
..2
..2
..2
..2
..2
...3
...3
...3
...3
...3
...3
...3
....4
....4
....4
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
C237
C807
CR402S
CR403S
GT02A
HC002
IC301
2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5
2401-002241 C-AL;220uF,+30-10%,400V,GP,ST,30x40
2301-001219 C-FILM,MPE-PPF;3.9nF,5%,1.6KV,TP,29x8.5x
2306-000188 C-FILM,MPPF;330nF,5%,400V,TP,26x19.5x11,
AA39-20010B LEAD CONNECTOR-ASSY;,1P,YFH800-01,S,500,
AA13-00087A IC HYBRID;-,TAR001,SIP,10P,-,BK
AA96-50345E ASSY-H/S;-,VERT,AA62-30174A,TDA8356/N6A
AA62-30174A HEAT SINK-PS;-,SPC,T1.0,-,33X20X50,-,FTAA61-10162A BRACKET-IC;-,SBHG-1,T1.0,-,-,-,6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR
1204-001541 IC-VERTICAL DEF.;TDA8356/N6A,SIP,9P,-,PL
0205-000129 GREASE-SILICON;SC102,JAPAN
1201-001386 IC-POWER AMP;7267,DIP,16P,-,DUAL,32dB,PL
AA96-50298C ASSY-H/S;-,POWER,AA62-30171A,KA3S0680,C
AA63-30189A COVER-HEATSINK;-,-,AA62-30171,PC-ABS,V0,
AA62-30171A HEAT SINK-ES;-,A6063 EXTR,-,-,-,WHT,40(3
AA61-10386A BRACKET-IC;-,SECC 100,T1.0,-,-,-,KA2S068
6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
1203-001313 IC-PWM CONTROLLER;3S0680,TO-3P,5,150MIL,
0205-000129 GREASE-SILICON;SC102,JAPAN
AA96-50407B ASSY H/S;-,VERTICAL,AA62-30154G,KA7806,
0205-000129 GREASE-SILICON;SC102,JAPAN
1203-000284 IC-POSI.FIXED REG.;7806,TO-220,3P,-,PLAS
6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
AA62-30154G HEAT SINK-ES;-,A6063 EXTR,-,WHT,50/16,-,
AA96-50153H ASSY-H/S;-,-,AA62-30013D,KA78R09,1203-001225 IC-POSI.FIXED REG.;78R09,TO-220,4P,-,PLA
6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
AA62-30013D HEAT SINK-ES;-,A6063 EXTR,-,-,55(21) T02
1203-001752 IC-POSI.FIXED REG.;LF33CV,TO-220,3P,-,PL
3722-000161 JACK-PIN;2P,3.4mm,SN,BLK,AA27-20003U COIL-DEGAUSSING;-,14,16.4ohm,75T,890mm,D
AA27-30001K COIL-LINEARLITY;-,230uH,DR1215,PI0.5,14.
AA29-30001C FILTER-LINE NOISE;-,39mH,1.0A,-,AA26-00004A TRANS-FLYBACK;-,FSA38026S,14INCH,125V
AA26-20007U TRANS-SWITCHING;-,90~260V,125V/16.5V/9.5
AA40-10006MTUNER-F/S;TECC2949PG29A(S),PAL-B/G,TR,18
AA99-30224S ASSY-PCB ROBOT; AA94-02669C ,ER
3711-003641 CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIG
3711-003641 CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIG
2306-000318 C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm
2306-000318 C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm
2201-000987 C-CERAMIC,DISC;2.2nF,20%,400V,Y5U,TP,12.
2201-000987 C-CERAMIC,DISC;2.2nF,20%,400V,Y5U,TP,12.
AA96-00111C ASSY-H/S;-,-,AA62-30013L,FML-G12S,0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
AA62-30013L HEATSINK-ES;-,-,-,-,44/22,-,WHT,-,-,-,0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,3601-000261 FUSE-CARTRIDGE;250V,3.15A,TIME-LAG,GLASS
1204-001440 IC-VIDEO SYSTEM;TDA8842,DIP,56P,300MIL,P
0801-000961 IC-CMOS LOGIC;4053,MUTIPLEXER,DIP,16P,30
0801-000213 IC-CMOS LOGIC;4052,MULTIPLEXER,DIP,16P,3
AA09-00088A IC MICOM;SAA5543PS/M4-0258,C15C,52P,3.3
1103-000118 IC-EEPROM;24WC08,1Kx8Bit,DIP,8P,300MIL,1
1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW,T
0604-001038 PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST
1404-000002 THERMISTOR-PTC;9ohm,20%,-,-,TR,RECT,0502-001115 TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,83501-001040 RELAY-POWER;12VDC,500mW,10A,1FormA,15mS,
2904-001239 FILTER-SAW AV;38.9MHz,SIP5K,ST,16.3dB,B/
AA26-50001B TRANS-HORIZ.DRIVE;-,7.1mH,102uH,10-20uH,
AA99-10218N ASSY-PCB MAIN,AUTO; AA99-30224S ,V
IC601
IC801S
IC804
IC806
IC903
JS701
L803
LR401S
LX801S
T444S
T801S
TU01S
CN101
CN102
CX801S
CX802S
CY801S
CY802S
D818
D820
FP801S
IC201S
IC701
IC702
IC901S
IC902S
NT801S
PC801S
PT801S
Q401
RL801S
SF101S
T401
Samsung Electronics
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
C101
C102
C107
C108
C109
C112
C201
C202
C204
C205
C206
C207
C208
C209
C210
C211
C212
C213
C214
C215
C219
C221
C222
C225
C226
C227
C228
C230
C231
C232
C233
C234
C236
C238
C239
C249
C250
C251
C253
C254
C255
C257
C260
C261
C262
C265
C301
C302
C303
C304
C305
C306
C307
C308
C401
C405
C406
C407
C408
C409
C411
C412
C413
C414
C415
C601
C602
C604
Code No.
2401-000030
2202-000127
2202-000807
2401-000962
2202-000632
2305-000196
2401-002619
2305-000412
2301-000224
2401-000660
2306-000122
2401-001840
2305-000412
2305-000289
2305-000412
2301-000232
2306-000122
2306-000122
2306-000122
2401-000480
2201-000273
2306-000122
2401-001840
2401-000603
2401-000603
2202-000796
2309-000138
2401-002144
2401-000480
2202-000849
2202-000243
2301-000445
2301-000232
2301-000383
2401-000603
2401-000480
2306-000122
2306-000122
2202-000210
2202-000127
2401-002619
2202-000791
2202-000121
2301-000192
2202-000210
2401-002144
2202-000796
2401-002293
2305-000149
2305-000285
2202-000796
2401-002288
2305-000285
2305-000407
2301-000383
2305-000704
2201-000556
2401-002288
2201-000556
2401-001661
2201-000556
2401-000927
2401-003028
2201-000639
2305-000382
2401-001998
2305-000665
2401-002619
Description ; Specification
Remark
C-AL;22uF,20%,25V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;22nF,+80-20%,25V,Y5V
C-AL;22uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-FILM,MPEF;150nF,5%,63V,TP,-,5mm
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C-FILM,MPEF;220nF,5%,63V,TP,-,5mm
C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C-FILM,PEF;3.3nF,5%,50V,TP,8.1x4.5x13mm,
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,DISC;0.018nF,5%,50V,NP0,TP,5x3
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-FILM,PE-PPF;100nF,5%,50V,TP,20x16x8.5,
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3.
C-CERAMIC,MLC-AXIAL;33pF,5%,50V,SL,TP,3.
C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm
C-FILM,PEF;3.3nF,5%,50V,TP,8.1x4.5x13mm,
C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-CERAMIC,MLC-AXIAL;270PF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C-CERAMIC,MLC-AXIAL;270PF,10%,50V,Y5P,TP
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-AL;68uF,20%,100V,WT,TP,10x20,5
C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5
C-FILM,MPEF;220NF,5%,100V,TP,10.5X5.5X15
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-AL;470uF,20%,25V,WT,TP,10x20,5
C-FILM,MPEF;220NF,5%,100V,TP,10.5X5.5X15
C-FILM,MPEF;470nF,5%,100V,TP,-,5mm
C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
C-FILM,MPEF;100nF,5%,250V,TP,16.5x10.3x5
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-AL;470uF,20%,25V,WT,TP,10x20,5
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-AL;68uF,20%,100V,GP,TP,10x16,5
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-AL;22uF,20%,250V,GP,TP,13x20,5
C-AL;100uF,20%,25V,WT,TP,6.3x11,5
C-CERAMIC,DISC;0.68nF,10%,2kV,Y5P,TP,9x5
C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mm
C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C-AL;47uF,20%,25V,GP,TP,5x11,5
8-1
Block Diagrams
9. Block Diagrams
9-1 C15C Video Block Diagram
9-1-1 Notes
The TV’s 1st and 2nd tuners (and VCR module) are “multi-system.” compatible:
IC201 (TDA8842/8841) is the video, chroma, and deflection (VCD) IC .
9-1-1(A) TAPE PLAYBACK (REGARDLESS OF ORIGINAL RECORDING SYSTEM)
If the output PB signal of micom pin 6 is high, the PB signal outputs from module deck 2, passes
through IC 702 pins 2 and 3 and out to another VCR . The output signal of IC701 pin 1 (pin 15)
outputs from IC201S pin 17 .
9-1-1(B) VIEWING NORMAL CHANNEL WHILE RECORDING A SCRAMBLED CHANNEL:
The output CVBS (Composite Video Signal) of the 2nd IF outputs to IC702pin 3 when the micom’s pin 7
V/T/H (VCR tuner high) is high . The decoded signal goes to IC701 pin 2, where it is fed to IC 701 pin
4 (high output of micom’s’ pin 8— AV/Tuner), and out to VCR pin 4 (module deck) for recording.
9-1-1(C) VIEWING A SCRAMBLED CHANNEL WHILE RECORDING AN UNSCRAMBLED CHANNEL.
The output CVBS of the 2nd IF is fed from IC701 pin 5 to IC701 pin 4 (low output of micom
pin 8—AV/tuner). Then it goes to the module deck pin 4 for recording.
The scrambled signal (CVBS) is fed to IC702 pin 1 through the 1st IF, and then to IC702 pin 3 (micom’s
pin 7, V/T/H registers low). Then it goes to the decoder input. The descrambled signal goes to IC701
pins 2 and 15 (PH high output of micom’s pin 6), and then to IC201S pin 17, where it outputs as RGB.
9-1-1(D) SYNCHRONOUS RECORDING:
The viewer sees the signal from the 1st tuner , while the signal from the second tuner is recorded.
Audio processing for the French system type is shown in the table.
Samsung Electronics
9-1
Wiring Diagram
10. Wiring Diagram
10-1 C15C Wiring Diagram
Samsung Electronics
10-1
Schematic Diagrams
11. Schematic Diagrams
11-1 VCR (SECAM BLOCK)
: Power Line
: Signal Line
Samsung Electronics
11-1
Schematic Diagrams
11-2 VCR (SYSTEM BLOCK)
TP1
TP1
TP6
TP4
TP5
TP2
TP2
TP3
TP3
TP4
TP5
TP6
11-2
Samsung Electronics
Schematic Diagrams
11-3 VCR (A/V BLOCK)
TP1
TP3
TP2
TP3
TP4
TP5
TP4
TP5
TP2
TP1
Samsung Electronics
11-3
Schematic Diagrams
11-4 VCR (POWER BLOCK)
: Power Line
: Signal Line
11-4
Samsung Electronics
Schematic Diagrams
11-5 TV MAIN (1/4)
TP1
TP2
TP3
TP4
TP5
: Power Line
: Signal Line
Samsung Electronics
11-5
Schematic Diagrams
11-6 TV MAIN (2/4)
TP1
TP5
TP4
TP2
TP3
TP6
TP3
TP4
TP2
TP1
TP5
TP6
: Power Line
: Signal Line
11-6
Samsung Electronics
Schematic Diagrams
11-7 TV MAIN (3/4)
TP 8
TP12
TP1
TP2
TP 7
TP11
TP3
TP4
TP5
TP6
: Power Line
: Signal Line
Samsung Electronics
11-7
Schematic Diagrams
11-8 TV MAIN (4/4)
: Power Line
: Signal Line
11-8
Samsung Electronics
Schematic Diagrams
11-9 TUNER-IF NICAM(STEREO)
: Power Line
: Signal Line
Samsung Electronics
11-9
Schematic Diagrams
11-10 2’nd IF(STEREO)
: Power Line
: Signal Line
11-10
Samsung Electronics
Schematic Diagrams
11-11 IF (MONO)
11-12 CRT
11-13 2'nd IF PAL/SECAM-B/G, D/K, I OPTION (MONO)
TP3
TP2
TP1
TP1
TP2
TP3
: Power Line
: Signal Line
Samsung Electronics
11-11
Schematic Diagrams
11-15 CONTROL
11-14 MASTER
11-16 FRONT-A/V (MONO)
11-17 FRONT-A/V (STEREO)
: Power Line
: Signal Line
11-12
Samsung Electronics
Schematic Diagrams
11-18 Voltages (VTR)
ICM301
1
ICM901
PLAY
REC
STOP
2.5
2.5
2.5
34
PLAY
REC
STOP
1.8
1.8
1.8
67
PLAY
REC
STOP
4
4
4
ICM602
ICM601
5
3
4
5
5
4
0
69
5
0
0
70
5
5
36
0
5
5
37
0
5
5
0
5
5
4
2
0
0
3
2
0
0
0
2
68
35
0
0
0
0
2
0.8
0
0
5
0.8
0
0
5
4
5
0
5
1
67
34
1
STOP
STOP
STOP
STOP
REC
REC
REC
REC
PLAY
PLAY
PLAY
PLAY
PLAY
REC
STOP
1
0.9
0.9
0
2
2
2.6
2.6
0
4
4
3
5.2
5.2
5.2
3.5
3.5
3.5
4
2.6
2.6
2.6
2
2.5
2.5
2.5
35
3.5
3.5
3.5
68
0
0
0
3
2.5
2.5
2.5
36
1.8
1.8
2
69
0.7
0.7
0.7
4
2.5
2.5
2.5
37
4.9
4.9
5
70
2
2
2
5
2.5
2.5
0
38
1.8
1.8
1.8
71
2.5
2.5
2.5
6
2.5
2.5
2.5
39
4
4
4
72
0.3
2.5
3
5
5
5
5
38
5
5
5
71
0
0
0
7
2.5
2.5
2.5
40
5
5
5
73
2.5
2.5
3.5
6
5
5
5
39
5
5
5
72
1.8
1.8
1.8
5
0
0
0
5
2.6
2.6
2.6
8
0
0
0
41
2.7
2.7
3
74
2
0
2
7
5
5
5
40
0
0
0
73
0
0
0
6
0
0
0
6
2.6
2.6
2.6
9
0
0
0
42
3
3
3.2
75
5
5
5
8
5
5
5
41
5
5
5
74
0
0
0
7
0
0
0
7
5
5
0
10
1.6
1.6
2
43
1.9
1.9
2
76
2.5
2.5
2.5
9
5
5
0
42
5
5
5
75
0
0
0
11
3.2
3.2
3.2
44
4.3
4.3
0
77
0
0
0
10
5
5
0
43
5
5
5
76
0.7
0.7
0.7
8
2.5
2.5
2.5
8
5
5
0
12
5
2
2.5
45
1.8
1.8
2
78
2.5
2.5
0
11
0
0
0
44
5
5
5
77
0.7
0.7
0.7
9
2.5
2.5
2.5
9
12.5
2.5
0
0
0
45
0
0
0
78
0
0
0
10
2.5
2.5
2.5
10
13
0
0
0
46
0
0
0
79
0
0
0
14
5
5
5
47
0
0
0
80
0
0
0
11
2.5
2.5
2.5
11
0
5
12.5
0
13
12
5
5.1
15
3.5
3.5
3.5
48
5
5
5
81
3
0
0
12
4.5
4.5
4.5
12
5
5
5.1
16
4.5
4.5
4.5
49
5
5
5
82
4
0
0
13
2.5
2.5
2.5
13
0
0
14
2.5
4.7
4.5
14
0
0
0
0
1.5
79
2
9
80
2.5
5
2.5
2.3
2.2
81
0
0
0
1.2
1
82
1.8
4.1
1
0
0
0
83
0
0
0
17
0
0
0
50
5
5
5
83
0
0
0
51
1.9
1.9
0
84
1.8
4.1
1
18
4.5
4.5
4.5
51
5
5
5
84
0
0
0
52
2.4
2.4
2.5
85
1.8
4.1
1
19
3.5
3.5
3.5
52
5
5
5
85
2.5
5
2.5
15
3
2.5
2.5
15
0
0
0
0
0
20
5
5
5
53
5
5
5
86
2.5
5
2.5
16
5
1
1
16
8.4
8.8
17
2.5
2.5
2.5
17
8.4
8.8
13
1.5
1.5
2
46
1.5
14
1.5
1.5
1.6
47
2
15
2.2
2.2
2.2
48
2.3
16
5
5
5
49
1.2
17
3
0
0
50
18
1.8
2.1
2.2
19
2.1
2.1
2.2
1.4
2.5
2.5
0
0
0
20
2.8
2.8
3.2
53
0
0
0
86
21
2.1
2.1
2.5
54
2.4
2.4
2.5
87
5
5
5
21
0
0
0
54
5
5
5
87
2.5
2.5
2.5
22
0
0
0
55
5
5
5
88
1.8
4.1
2
22
0
0
0
55
0
5
0
88
2.5
2.5
2.5
23
5
5
5
56
3.5
3.5
0
89
0
0
0
23
5
5
0
56
0
0
0
89
2.5
2.5
2.5
18
2
2
2
18
8.4
8.8
0
0
2.5
2.5
2.5
19
2.5
2.5
2.5
19
5.2
5.2
0
20
2.5
2.5
2.5
20
0
0
0
24
5
5
5
57
3.4
3.4
3.5
90
1.8
4.1
2
24
5
5
0
57
0
0
0
90
25
5
5
0
58
5
5
5
91
0
0
0
26
0
0
0
59
5
5
5
92
5
5
5
27
5
5
5
60
5
5
5
93
5
5
5
21
2.5
2.5
2.5
21
12.5
12.5
13
8.2
8.2
0
8.2
0
25
1.8
1.8
2.8
58
5
5
5
91
1.8
4.1
2
26
0.8
0
1
59
3.4
3.4
3.5
92
4
1.6
0
27
4.1
4.1
4.1
60
3.5
3.5
3.5
93
4
4.0
0
28
5
5
5
61
5
5
5
94
0
5
0
22
5
5
5
22
8.4
28
4.1
4.1
4.1
61
3.3
3.3
3.5
94
0.5
0.7
0
29
5
5
0
62
0
0
0
95
0
0
0
29
0.8
0.8
3
62
3.5
3.5
3.5
95
0
0
0
23
3
3
3
23
30
0
0
0
63
0
0
0
96
5
5
5
30
1
0
1
63
4
4
0
96
2.5
2.5
2.5
31
0
0
0
64
5
5
5
97
5
5
5
24
3
3
3
24
8.4
8.4
31
2.1
2.1
3.5
64
2.2
2.2
0
97
0
0
0
32
5
5
5
65
0
0
0
98
5
5
0
25
4.1
3
3
25
1.8
1.8
2.6
32
1.8
1.8
2
65
2.4
2.4
2.2
98
2.5
2.5
2.5
33
0
0
0
66
0
5
0
99
5
5
0
26
5
0
0
26
1.8
2
2
1.5
66
2.5
2.5
3
99
5
4.3
5
100
5
5
5
27
4.1
4.1
4.1
27
100
2.5
2.5
2.5
1.4
1.8
1.4
0
33
28
3.1
3.1
3.1
28
2.4
2.5
2
27
5.2
0
5.2
0
0
0
28
Samsung Electronics
0
1
11-13
Schematic Diagrams
11-19 Voltages (TV)
Q801
KA3S0680RF
:
Units : Volts
PIN NO
PIN NAME
ST AND-BY
POWER ON
1
DAR.IN
299
290
2
GND
-
-
3
VCC
19.5
20.3
4
VFB
0.2
1.3
5
SYNC
0.8
6.7
IC902
PC123Y
:
Units : Volts
PIN NO
ST AND-BY
POWER
1
16.5
16.7
2
15.4
15.7
3
GND
GND
4
0.2
1.3
IC501
TDA6107Q
:
Units : Volts
IC901
SAA5554PS-OTP
Units : Volts
PIN NO
PIN NAME
VOL T AGES(V )
1~4
GND
-
PIN NO
PIN NAME
VOL T AGES(V)
PIN NO
PIN NAME
VOL T AGES(V )
S-L CTL
-
37
N.C
-
5
SDA
4.8
1
6
SCL
4.8
2
BUS-STOP
5.2
38
GND
-
7
GND
-
3
D-coil
-
39
GND
-
8
VDD
5.2
4
ST BY-REC
-
40
S-MUTE
2.8
5
PB-L
-
41
VDD
3.2
6
AV-L
0.67
42
OSD B
-
0.67
43
OSD G
-
OSD R
-
:
TDA7267A
Units : Volts
PIN NO
PIN NAME
VOL T AGES(V )
1
VS
1.6
2
OUT
8.5
3
SVR
8.7
4
IN
0.8
5
N.C
-
6
S-GND
-
7~8
N.C
-
9~16
P-GND
-
7
VT-L
8
HOLD
2.48
44
9
1T/AFT
3.2
45
F/B
-
10
2T/AGC
2.7
46
H-SYNC
0.79
11
2T/AFT
3.2
47
V-SYNC
-
12
SCART-ID
-
48
VSSP
-
13
GND
-
49
VDD
3.2
14
BG/I
-
50
GND
-
15
D/K
-
51
Xtal
1.6
PIN NO
PIN NAME
VOL TAGE S(V )
16
1TS-L H
5.2
52
Extal
1.6
1
B-IN
2.4
17
S-L H
4.9
53
RESET
-
2
R-IN
2.4
18
FRA-H
3.7
54
VDD
3.2
3
G-IN
2.5
19
LNA
4.4
55
REMOCON
5.2
4
GND
-
20
TV PWR
3.2
56
TV CLK
5.1
5
lom
5.4
21
PB MUTE
-
57
V-SYNC INTER
-
6
Vdd
166
22
VSSA
-
58
TV SI
-
7
G-OUT
90~115
23
CVBS0
0.2
59
TV SO
1.0
8
R-OUT
93~118
24
CVBS1
1.3
60
TV CS
-
9
B-OUT
97~119
25
BLACK
0.48
61~62
SCL
2.3
IREF
1.3
63~64
SDA
2.2
26
IC301
11-14
:
Units : Volts
IC601
IC801
24C08,24C04,24C16
:
:
TDA8356
Units : Volts
PIN NO
PIN NAME
VOL T AGES(V )
1
VD-INPUT
2.2
2
VD+INPUT
2.2
3
VCC
16.9
4
OUTPUT
8.2
5
GND
-
6
VFB
41.5
7
OUT
8.5
8
VO
-
9
VI
8.2
Samsung Electronics
Schematic Diagrams
11-20 Voltages (TV)
L OC
IC101*
IC101*
IC
TDA9818
2T-IF(F)
LA7565B
2T-IF(W)
PIN NO
1
3.3
2.0
IC701
TC4053BP
-
IV702
TC4052BP
1.6
ICL 01*
STV8225
4.2
2
3.3
2.2
-
0.5
3.2
3
-
7.4
-
1.6
-
4
2.0
8.0
1.1
-
0.6
5
6
7
8
2.1
3.9
1.7
2.4
8.9
3.8
3.2
2.7
1.1
-
2.2
-
4.3
3.5
4.3
6.3
9
2.3
3.7
0.8
0.8
4.3
10
2.3
2.7
0.8
0.8
3.5
11
1.6
8.3
0.8
-
4.3
12
13
14
2.0
2.7
4.2
8.3
0.3
7.9
2.2
2.1
4.0
3.4
2.2
15
1.4
-
-
0.4
16
1.9
-
8.9
8.9
17
0.4
2.9
18
19
20
21
2.6
2.6
4.9
3.4
3.4
1.7
22
0.8
2.4
23
3.2
3.3
24
3.2
Samsung Electronics
3.3
9.0
4.3
4.3
IC201
:
TDA8842/8841
Units : Volts
PIN NO
PIN NAME
VOL TAGE S(V )
P I N NO
1
SOUND IF INPUT
-
31
B-Y
OUTPUT
-
2
EXT.AUDIO INPUT
3.6
32
R-Y
OUTPUT
-
3
N.C
-
33
P I N NA M E
SUBCARRIER
V O L T A G E S(V )
OUTPUT
-
4
N.C
-
34
X-TAL(3.58)
2.4
5
PLL LOOPFILTER
2.4
35
X-TAL(4.43/3.58)
2.4
6
IF VIDEO OUTPUT
3.2
36
7
SCL
4.8
37
POSITIVE
8
SDA
4.8
38
CVBS
9
BANDGAP DECOUPLING
6.6
39
DECDIG
4.9
10
CHROMA INPUT
-
40
HOR OUTPUT
0.3
11
Y/CVBS INPUT
3.3
41
12
MAIN POSITIVE SUPPLY
8.0
42
13
INT.CVBS INPUT
3.9
43
14
GND
-
44
15
AUDIO OUT
3.0
45
16
SECAM DECOUPLING
-
46
VERT.DRIVE
POS
2.2
17
EXT.CVBS INPUT
3.3
47
VERT.DRIVE
NEG
2.2
18
BLACK CURRENT INPUT
5.0
48
IF INPUT
4.5
19
BLUE OUTPUT
3.0
49
IF INPUT
4.5
20
GREEN OUTPUT
3.2
50
21
RED OUTPUT
3.2
51
VERT.SAWTOOTH
22
V-GUARD INP / BEAM CUR.LIMITTER
2.0
52
REFERENCE
23
RED INPUT
3.4
53
24
GREEN INTPUT
3.4
54
25
BLUE INTPUT
3.4
55
26
RGB INSERTION SWITCH INP
0.1
56
27
LUMINANCE INPUT
2.6
28
LUMINANCE OUTPUT
2.6
29
B-Y OUTPUT
-
30
R-Y OUTPUT
-
LOOPFILTER
BURST
SANDCASTLE
PHASE
DET
4.9
SUPPLY
8.0
OUTPUT
2.7
OUTP/FLY-BACK
PHI2 FILTER
INP
/ FLASHPROT
3.2
PHI1 FILTER
3.9
GND
EAST-WEST
AGC
-
DRIVE/AVL
EHT/OVERVOLTAGE
0.5
OUTPUT
PROTECTION
CAPACITOR
CURRENT
INPUT
-
INP
2.1
3.7
3.8
DECOUPLING
CAPACITOR
4.2
TUNER
INPUT
4.4
DEEMPHASSIS
2.8
AUDIO
DECOUPLING
AGC
SOUND
DEMODULATOR
2.4
11-15
Wiring Diagram
10-2 C15C Wiring Diagram
10-2
Samsung Electronics
Block Diagrams
9-2 C15C Video Block Diagram (Continued)
ANT
MICOM#24
SDA
MICOM #23
SCL
ICT01
TTX
#8
7
IC201
8
38
R
1st
IF
1st Tunning
CRT
Drive
G
IF
DET.
B
INT
EXT
17
13
6
IC702
9
PB H
Micom #6
2
10
V/T/H
Micom #7
1
3
Trap
1T.option
2nd
IF
2nd Tunning
5
C15A OPTION
15
IC701
V-in
PB H
11
10
Micom #6
1
#13
L
H
5
2
V-out
VCR
or
Decorder
3
VPS
ICP01
Micom #8
CN101 PB.V
Module
DECK
9
2
4
AV/Tuner
4
CN101
REC. SOURCE V.
Micom Pin Function
PIN NO.
6
7
8
56, 57
23,24
9-2
PIN NAME
PB H
V/T/H
AV/TUNER
FUNCTION
High Output : Playback signal is monitored. The PB signal is output at scart.
High Output : The second tuner signal is output at scart.
High Output : AV signal is recorded. Low output : TUNER signal is recorded.
S-L H
FRA H
FRA H
Port S-L H
S
L
L
PAL/SEC
L
H
FRANCE-L
H
L
FRANCE-L'
a C. SYSTEM : PAL/SEC ARE AUTO mode, and France is SECAM mode.
Extra control signals are all controlled by the I2C bus.
Select INT/EXT
FRENCH system modulation
SDA,SCL
Samsung Electronics
Block Diagrams
9-3 C15C Audio Block Diagram (MONO)
ANT
MICOM#24
SDA
MICOM #23
SCL
7
8
IC201
SPK
1st
IF
1st Tunning
15
IF
PROCESS
INT
6
EXT A
2
55
14
ZK01
ZK02
2nd
IF A-0
2nd Tunning
1
IC701
HC002
13
11
H
Micom #5
C15COPTION
MICOM14 BG/I L
MICOM15 DK/L
12
S/L (AM)
EXT
ZK03
ZK04
A out
REC. SOURCE A.(TUNER)
A in
CN101
8
Module
DECK
6
10
REC. SOURCE A.(EXT)
PB.A
EXT.A
IF IN
11
S-L CTL
1T
Switch
1T.A
9
om
pti
.o
7
B
Micom #17
VCR
or
Decoder
14
12
9
H
15
10
H
10
(AM) S-L
A
C
5
1T.A
B/G (FM)
13
L
L
Micom #5
Micom #7
IC702
Micom Pin Function
PIN NO.
6
7
8
60
53,54
Samsung Electronics
PIN NAME
PB H
V/T/H
AV/TUNER
S-L CTL
a :S-L(AM)
b : B/G (FM)
c :EXT
SDA, SCL
BG/I L
DK/L
FUNCTION
High output : PB audio is monitored. The PB audio is output at scart.
High output : The second tuner audio is output at a scart.
High output : AV audio is recorded. Low output : TUNER audio is recorded.
1 1.8 ~ 2.6V : In TV FM Mode, connect pin 7 to A and pin 9 to C.
2 4.1 ~ 4.9V : In TV AM Mode, connect pin 7 to A and pin 9 to A.
3 6.4 ~ 7.2V : In AV-AM Mode, connect pin 7 to B and pin 9 to A.
4 More than 7.3V : In AV-FM Mode, connect pin 7 to B and pin 9 to C.
S
AUTO
BG
DK
I
Port
B/G
D/K
L
L
H
L
L
H
L
H
9-3
Block Diagrams
9-4 C15C Audio Block Diagram (Only Stereo)
ANT
OPTION
EXT- L
2F
TDA
EXT- R
1 Tuner
7297
Nicam Module
INT- L
MSP 3410
IC601
INT- R
IC602
SCL
2Tuner L
2Tuner R
EXT- L
EXT- R
SDA
MICOM
PB PB
L R
Decoder
2Tuner
REC - L
IF Module
REC - R
Module
EXT- L
Deck
EXT- R
TDA9874
9-4
Samsung Electronics
Electrical Parts List
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
! ....4
....4
....4
8-2
Code No.
C605
C606
C607
C608
C701
C702
C703
C704
C705
C706
C708
C710
C711
C715
C717
C724
C725
C726
C729
C730
C804
C805
C806
C808
C810
C811
C812
C813
C815
C816
C819
C820
C822
C823
C824
C825
C827
C828
C829
C830
C831
C832
C835
C839
C840
C844
C850
C853
C901
C902
C903
C904
C905
C907
C908
C909
C910
C911
C912
C913
C915
C916
C918
C919
C920
C921
C922
C923
CB03
CK02
CN501C
CN601
CN701
CN702
CR401S
CW901
D102
Description ; Specification
2301-000445
2401-000603
2401-000914
2401-001998
2401-000471
2401-001989
2202-000121
2202-000121
2401-002463
2202-000121
2401-002144
2401-000471
2401-000480
2401-002619
2401-000471
2401-001989
2401-000480
2401-002619
2401-000480
2401-000480
2401-002619
2401-002300
2301-000310
2301-001435
2301-000224
2301-000192
2201-000374
2201-000991
2201-000991
2201-000991
2401-000293
2401-000293
2401-002300
2401-001840
2401-002463
2401-002215
2306-000122
2401-002463
2401-002144
2401-001840
2401-002463
2306-000122
2401-002291
2401-002215
2306-000122
2401-002594
2401-001176
2401-001397
2202-000632
2306-000122
2202-000796
2401-000590
2201-000980
2201-000980
2401-002144
2202-000632
2401-003102
2401-001333
2202-000632
2401-002144
2301-000188
2401-000480
2202-000632
2202-000632
2305-000355
2202-000791
2202-000791
2202-000796
2202-000127
2202-000121
3711-002648
3711-002642
3711-002648
3711-002644
2201-002028
2503-000156
0401-000005
Remark
C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;22uF,20%,16V,GP,TP,5x11,5
C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C-AL;10uF,20%,50V,BP,TP,5x11,5mm
C-AL;4.7uF,20%,50V,BP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C-AL;470uF,20%,16V,GP,TP,8x11.5,5
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-AL;10uF,20%,50V,BP,TP,5x11,5mm
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-AL;10uF,20%,50V,BP,TP,5x11,5mm
C-AL;4.7uF,20%,50V,BP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-AL;47uF,20%,50V,GP,TP,6.3x11,5
C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,
C-FILM,PPF;1.5nF,5%,1.2kV,TP,15x8x12.5mm
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5
C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C-CERAMIC,DISC;0.22nF,5%,50V,NP0,TP,10.5
C-CERAMIC,DISC;0.56nF,10%,2kV,Y5P,TP,7.5
C-CERAMIC,DISC;0.56nF,10%,2kV,Y5P,TP,7.5
C-CERAMIC,DISC;0.56nF,10%,2kV,Y5P,TP,7.5
C-AL;100uF,+30-10%,200V,GP,TP,16x25
C-AL;100uF,+30-10%,200V,GP,TP,16x25
C-AL;47uF,20%,50V,GP,TP,6.3x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;470uF,20%,16V,GP,TP,8x11.5,5
C-AL;2200uF,20%,25V,WT,TP,13x25,5
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-AL;470uF,20%,16V,GP,TP,8x11.5,5
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;470uF,20%,16V,GP,TP,8x11.5,5
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-AL;47uF,20%,16V,GP,TP,6.3x5,5
C-AL;2200uF,20%,25V,WT,TP,13x25,5
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-AL;220uF,20%,16V,GP,TP,8x11.5,5
C-AL;33uF,20%,25V,GP,TP,5x11,5
C-AL;470uF,20%,25V,GP,TP,10x16,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-AL;1uF,20%,50V,GP,TP,3x5,5
C-CERAMIC,DISC;0.03nF,5%,50V,NP0,TP,5x3,
C-CERAMIC,DISC;0.03nF,5%,50V,NP0,TP,5x3,
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;100uF,20%,10V,GP,TP,5x11,5
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-FILM,PEF;1nF,5%,100V,TP,10.5x12.5x6.5,
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-FILM,MPEF;330nF,5%,63V,TP,-,5mm
C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
CONNECTOR-HEADER;BOX,9P,1R,2.5mm,STRAIGH
CONNECTOR-HEADER;BOX,3P,1R,2.5MM,STRAIGH
CONNECTOR-HEADER;BOX,9P,1R,2.5mm,STRAIGH
CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGH
C-CERAMIC,DISC;0.47nF,10%,2kV,Y5P,TP,7.5
C-NETWORK;100pFx4,20%,50V
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
Loc. No.
!
!
!
!
!
!
!
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
D201
D202
D205
D209
D210
D401
D402
D403
D404
D405
D407
D601
D607
D801S
D802S
D803S
D804S
D805
D806
D808
D809
D811
D812
D821
D824
D831
D832
D833
D834
D901
D902
D903
D904
D905
D907
D908
D919
DK01
DZ201
DZ202
DZ203
DZ205
DZ206
DZ207
DZ208
DZ301
DZ302
DZ303
DZ304
DZ601
DZ608
DZ701
DZ702
DZ703
DZ704
DZ802
DZ803
DZ804
DZ805
DZ809
DZ810
DZ901
DZ902
DZ904
DZ907
F81
F82
FD801S
FD802S
HC001S
IC802
IC803
L101
L108
L201
L202
L205
Code No.
Description ; Specification
Remark
0401-001073 DIODE-SWITCHING;MA859,35V,100MA,DO-34,TP
0401-001073 DIODE-SWITCHING;MA859,35V,100MA,DO-34,TP
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP
0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T
0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP
0404-001056 DIODE-SCHOTTKY;RK16,60V,1.5A,DO-204AC,TP
2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
0403-000714 DIODE-ZENER;MTZJ3.3B,3.3V,3.32-3.53V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
0403-000714 DIODE-ZENER;MTZJ3.3B,3.3V,3.32-3.53V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D
0403-001039 DIODE-ZENER;MA2560,56V,52-60V,1W,DO-41,T
0403-001039 DIODE-ZENER;MA2560,56V,52-60V,1W,DO-41,T
0403-001325 DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,D
0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO
0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,T
0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
0403-000705 DIODE-ZENER;TZP8.2B,8.2V,8.2-9.3V,1W,DO0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO
0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO
0403-001316 DIODE-ZENER;MTZJ3.0A,2.85-3.07V,500mW,DO
3602-000114 FUSE-HOLDER;-,-,30mohm
3602-000114 FUSE-HOLDER;-,-,30mohm
3601-001086 FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS
3601-001086 FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS
AA13-20004W IC-HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TP
1203-001217 IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL
1203-000293 IC-POSI.FIXED REG.;7808,TO-220,3P,-,PLAS
2701-000202 INDUCTOR-AXIAL;560nH,10%,2.5x3.4mm
2701-000177 INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm
2701-000184 INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm
2701-000146 INDUCTOR-AXIAL;2.2uH,10%,2.5x3.4mm
2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
Samsung Electronics
Electrical Parts List
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
L301
L302
L303
L304
L403
L405
L406
L601
L701
L702
L704
L802
L805
L809
L810
L812
L813
L817
L901
L902
L905
L906
L907
L908
PCB
Q201
Q202
Q203
Q204
Q205
Q206
Q207
Q402
Q601
Q603
Q701
Q802
Q901
Q903
Q906
R102
R103
R105
R107
R118
R119
R202
R203
R204
R205
R206
R207
R208
R209
R212
R213
R215
R216
R218
R219
R220
R221
R222
R223
R225
R226
R227
R230
R234
R237
R243
R244
R247
R248
R249
R250
R252
Code No.
Description ; Specification
2701-000116
2701-000116
2701-000111
2701-000111
2901-000297
2701-001030
2701-000002
3301-000287
2701-000114
2701-000114
2701-000114
3301-000287
3301-000287
3301-000287
2701-001032
3301-000287
3301-000287
2901-000297
2701-000114
2701-000114
2701-000116
2701-000211
2901-000297
2701-000114
AA41-00145C
0501-000389
0501-000389
0501-000389
0501-000389
0501-000389
0501-000389
0501-000389
0501-000369
0504-000123
0502-000242
0501-000283
0501-000369
0501-000389
0501-000389
0501-000369
2001-000660
2001-000281
2001-000281
2001-000281
2001-000613
2001-000331
2001-000281
2001-000281
2001-000281
2001-000005
2001-000008
2001-000281
2001-000281
2001-000281
2001-000273
2001-000016
2001-000008
2001-000947
2004-001914
2001-000016
2001-000429
2001-000429
2001-000429
2001-000429
2001-000273
2001-000780
2001-000780
2001-000281
2001-000429
2001-000563
2001-000429
2001-000780
2001-000490
2001-001352
2001-000832
2001-000857
2001-000780
Samsung Electronics
Remark
INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;100uH,10%,2.5x3.4mm
FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;43uH,10%,5x14mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,
CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,
CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,
INDUCTOR-AXIAL;100uH,10%,5x14mm
CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,
CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,
FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;68uH,10%,2.5x3.4mm
FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
PCB-MAIN;TF21B3N3X,FR-1,1L,A,1.6T,330x2
S.N.A
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC2331-Y,NPN,1000mW,TOTR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,T
TR-POWER;KSA614,PNP,25W,TO-220,TP,40-24
TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T
TR-SMALL SIGNAL;KSC2331-Y,NPN,1000mW,TOTR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-SMALL SIGNAL;KSC2331-Y,NPN,1000mW,TOR-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);1OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mm
R-CARBON(S);1OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;200OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;62OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
R253
R254
R255
R256
R257
R261
R264
R265
R267
R268
R301
R302
R303
R304
R305
R306
R401
R402
R403
R404
R405
R408
R409
R410
R413
R414
R415
R416
R417
R418
R419
R420
R421
R423
R606
R612
R613
R614
R615
R621
R705
R708
R709
R710
R711
R712
R713
R715
R716
R720
R721
R725
R726
R802
R804
R805
R806
R807
R808
R809
R810
R811
R813
R814
R815
R816
R821
R822
R824
R825
R828
R829
R830
R831
R832
R834
R835
Code No.
2001-000449
2001-000734
2001-000832
2001-000734
2001-000290
2001-000429
2001-000429
2001-000563
2001-000290
2001-000232
2004-000500
2004-004087
2008-000205
2003-000652
2001-000085
2008-000254
2001-000281
2001-000591
2001-001114
2003-001047
2003-000540
2008-000264
2008-000204
2008-001053
2001-001037
2001-000022
2003-000993
2008-000253
2008-000255
2001-001114
2001-000563
2001-000011
2003-000455
2004-001384
2001-000723
2008-001018
2008-001049
2001-000347
2001-000563
2001-001088
2001-000003
2001-000674
2003-000458
2001-000281
2001-000005
2001-000005
2001-000938
2001-000290
2001-000429
2001-000290
2001-000633
2001-000969
2001-000969
2001-000019
2001-001128
2003-000994
2003-000586
2001-000117
2001-000290
2001-000022
2001-001134
2001-001134
2001-001178
2001-001125
2004-004089
2004-001983
2001-001134
2004-001390
2001-000786
2006-001029
2001-000734
2001-000734
2001-000302
2003-000654
2001-000786
2003-000664
2003-000639
Description ; Specification
Remark
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-METAL;2.7Kohm,1%,1/8W,AA,TP,1.8x3.2m
R-METAL(S);1.5ohm,1%,1/2W,AA,TP,2.5x6.5m
R-FUSIBLE(S);10ohm,5%,1/2W,AF,TP,2.5x6.5
R-METAL OXIDE(S);330ohm,5%,2W,AF,TP,4x12
R-CARBON(S);100KOHM,5%,1/2W,AA,TP,2.4X6.
R-FUSIBLE(S);0.68ohm,5%,2W,AF,TP,3.9x10m
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4
R-METAL OXIDE(S);68ohm,5%,2W,AF,TP,3.9x1
R-METAL OXIDE(S);1Kohm,5%,2W,AF,TP,4x12m
R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm
R-FUSIBLE(S);0.22ohm,10%,1/2W,AF,TP,2.5x
R-FUSIBLE;22ohm,5%,1/2W,AF,TP,2.5x6.5mm
R-CARBON(S);0.39OHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4M
R-METAL OXIDE(S);3.9Kohm,5%,1W,AF,TP,2.5
R-FUSIBLE(S);0.47ohm,5%,1W,AF,TP,3.9x10m
R-FUSIBLE(S);1.5ohm,5%,1W,AA,TP,3.9x10mm
R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;75KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);100ohm,5%,2W,AA,TP,4x12
R-METAL(S);150Kohm,1%,1/2W,AA,TP,2.4x6.4
R-CARBON;4.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-FUSIBLE(S);0.47ohm,10%,2W,AF,TP,3.9x10
R-FUSIBLE(S);3.9OHM,5%,2W,AF,TP,3.9X10MM
R-CARBON;13KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4M
R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);100ohm,5%,2W,AF,TP,4x12
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;68OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;30KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4M
R-CARBON(S);30KOHM,5%,1/2W,AA,TP,2.4X6.4
R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
R-METAL OXIDE(S);22Kohm,5%,2W,AF,TP,4x12
R-CARBON(S);68OHM,5%,1/2W,AA,TP,2.4X6.4M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4M
R-CARBON(S);360ohm,5%,1/2W,AA,TP,2.4x6.4
R-CARBON(S);360ohm,5%,1/2W,AA,TP,2.4x6.4
R-CARBON(S);680OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2.4X6.
R-METAL(S);123Kohm,1%,1/2W,AA,TP,2.5x6.5
R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.
R-CARBON(S);360ohm,5%,1/2W,AA,TP,2.4x6.4
R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CEMENT;3.3ohm,5%,5W,CJ,TP,10.5x14x27m
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);33Kohm,5%,2W,AA,TP,4.3x
R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);33ohm,5%,2W,AF,TP,4x12m
R-METAL OXIDE(S);3.9ohm,5%,2W,AA,TP,4x12
8-3
Electrical Parts List
Loc. No.
!
!
!
!
!
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
..2
...3
..2
..2
..2
..2
..2
..2
..2
8-4
Code No.
R836
R860
R901
R902
R904
R905
R906
R907
R908
R909
R910
R911
R912
R913
R914
R916
R917
R918
R919
R920
R921
R922
R924
R926
R928
R930
R931
R935
R940
R941
R942
R943
R944
R945
R947
R948
R949
R953
R955
R957
R961
R962
R965
R966
R969
R972
R973
R974
R975
R976
RA802
RB802
RP801S
RR401S
RU102
RW701
RW901
RY801S
VP801S
VX801S
X202
X901
Z101
Z102
ZK01
Description ; Specification
2003-000639
2001-001054
2001-000449
2001-000449
2001-000554
2001-000554
2001-000554
2001-000628
2001-000429
2001-000780
2001-000449
2001-001062
2001-000812
2001-000331
2001-000429
2001-000429
2001-000281
2001-000429
2001-000539
2001-000435
2001-000449
2001-000429
2001-000281
2001-000281
2001-000281
2001-000734
2001-000281
2001-000429
2001-000281
2001-000429
2001-000429
2001-000734
2001-000734
2001-000429
2001-000281
2001-000281
2001-000331
2001-000734
2001-000734
2001-000429
2001-000908
2001-000290
2001-000429
2001-000007
2001-000734
2001-000429
2001-000290
2001-000290
2001-000290
2001-000290
2001-001129
2001-001129
2002-001011
2004-001390
2001-000290
2011-001133
2011-000531
2002-001012
1405-000152
1405-000152
2801-000274
2801-001381
2903-001019
2903-001040
2903-000184
AA98-60002E
0202-000187
AA60-10008A
AA63-00285B
AA63-40279A
AA65-30013A
AA65-30014A
AA65-30018A
AA65-30109A
Remark
R-METAL OXIDE(S);3.9ohm,5%,2W,AA,TP,4x12
R-CARBON(S);1.6KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;24KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1MOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;62KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);330KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON(S);330KOHM,5%,1/2W,AA,TP,2.4X6.
R-COMPOSITION;3.3Mohm,5%,1/2W,AA,TP,3.7x
R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-NETWORK;33K/24K/75x3,5%,1/8W,X,SIP,6P,
R-NETWORK;4.7Kohm,5%,1/8W,A,SIP,8P,BK
R-COMPOSITION;8.2Mohm,5%,1/2W,AA,TP,3.7x
VARISTOR;560V,2500A,14x8.5mm,TP
VARISTOR;560V,2500A,14x8.5mm,TP
CRYSTAL-UNIT;4.433619MHZ,30PPM,28-AAM,20
CRYSTAL-UNIT;12MHz,30ppm,28-AAA,30pF,50o
FILTER-CERAMIC;BR,5.5MHz,-,-,-,TP,FILTER-CERAMIC;TR,5.5/6.0/6.5MHz,-,1dB,FILTER-CERAMIC;BP,5.5MHz,120KHz,6dB,-,TP
ASSY-SUB,PART;SCV11D,MAIN,-,ALL
SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
SCREW-TAPPING;-,SWRCH18A,M3,L10,TH,+,-,SHIELD CASE;-,SPTE,T 0.5,C15C,TF14B5
SHIELD-CASE-IF;-,SPTE,T0.25,SCT53A,CW764
CLAMP-WIRE;-,NYLON-66,V0,-,NTR,DAWH-45N
CLAMP-WIRE;-,NYLON-66,V0,-,NTR,DATL-450CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60
CLAMP-FBT;-,NYLON-66,V2,-,BLK,-
Loc. No.
Code No.
Description ; Specification
Remark
ASSY-CRT
1
*
..2
..2
..2
! ..2
AA94-50008P ASSY-CRT;A34KQV42X,-300MG,14,BARE,TVCR
AA27-00041A
AA63-60028A
AA27-00001A
AA03-10002N
S.N.A
DEFLECTION-YOKE;-,QPC-E3704,14INCH,-,3.1
SPACER-DY;-,NEOPRENE,-,-,-,BLK,-,-,V0 W1
MAGNET-CONVERGENCE;-,JH225-06A,22.5MM
CRT-COLOR;-,A34KQV42X,-300MG,14,90DEG,5
ASSY-PCB,MASTER
1
*
..2 PCB
..2
..2
...3
..2
..2
..2
..2
AA95-00241A ASSY-PCB,MASTER;-,-,C15A,PAL,-,SET ALL
AA41-10578D PCB-MASTER;C15A,1L,CEM-1,245X245X1.6T,20
AA99-20067W ASSY-PCB SUB,AUTO; AA95-00241A ,V
AA98-60002H ASSY-SUB,PART;SCV11D,MASTER BOARD,-,ALL
0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
AA61-10320A BRACKET-MASTER;T3350,SECC,T1.0,-,-,-,3403-000179 SWITCH-PUSH;250V,5A,DPST,-,JPW-2104B
AA39-20041B LEAD CONNECTOR-ASSY;,2P,YFH800-02,S,300,
6001-000057 SCREW-MACHINE;RH,+,M3,L6,ZPC(BLK),SWRCH1
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
ASSY PCB CRT
1
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
...3
...3
...3
..2
..2
..2
..2
..2
..2
..2
..2
..2
! ..2
..2
...3
*
AA95-00629A ASSY PCB CRT;-,C15C,14,-,-
C502
C503
C504
C506
CN503A
CN503B
D501
D502
D503
D504
DZ501
DZ502
DZ503
DZ504
GT502A
IC501
2301-000213
2201-000723
2401-001232
2401-000430
AA39-20031C
3711-002648
0402-000216
0402-000546
0402-000546
0402-000546
0403-000720
0403-000720
0403-000720
0403-000720
AA39-20010B
AA96-50311A
1201-001159
6003-000334
AA62-30175D
PCB
AA41-00186A
R501M 2002-001009
R502M 2002-001009
R503
2002-001009
R504
2001-001062
R505
2008-001015
R510
2001-000281
R511
2001-000281
R512
2001-000281
V999S 3704-000103
AA98-60002F
0202-000187
C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5
C-CERAMIC,DISC;4.7nF,20%,3KV,Y5U,TP,16x5
C-AL;4.7uF,20%,250V,GP,TP,10x12.5,5
C-AL;10uF,20%,250V,GP,TP,10x16mm,5m
LEAD CONNECTOR-ASSY;,9P,67096-009,S,400,
CONNECTOR-HEADER;BOX,9P,1R,2.5mm,STRAIGH
DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-20
DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T
DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T
DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T
DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
LEAD CONNECTOR-ASSY;,1P,YFH800-01,S,500,
ASSY-H/S;-,VIDEO,AA62-30175D,TDA6107Q,IC-VIDEO AMP;6107,ZSIP,9P,-,SINGLE,-,PLA
SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR
HEAT SINK-PS;-,SECC,T1.0,-,33X15X30 FT-2
PCB-CRT;C15C,1L,FR-1,245x245x1.6T,9A,M
R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7
R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7
R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7
R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4
R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
SOCKET-CRT;10P,22.5,14.3,SN,ISMS01S/BK
ASSY-SUB,PART;SCV11D,CRT,-,ALL
SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
ASSY-PCB,A/V
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
1
*
AA95-00630B ASSY-PCB,A/V;-,14/20/21,C15C,PAL,-,MO
..2
..2
..2
..2
..2
..2
..2
..2
..2
CNC701
CNC701
CY702
JA01
JA02
JA03
LY701
LY702
PCB
AA39-20112D
AA39-20069D
2202-000121
3722-001343
3722-001342
3722-000145
2701-000116
2701-000114
AA41-00257A
LEAD CONNECTOR-ASSY;,9P,YBNH025-09,67096
LEAD CONNECTOR-ASSY;,5P,YBNH025-05,67096
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
JACK-RCA;1P,3.4MM,NI,WHT,JACK-RCA;1P,3.4MM,NI,YEL,JACK-PHONE;1P,3.6mm,MBAG,BLK,INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
PCB-MONO A/V;C15C,1L,FR-1,245x245x1.6T,3
S.N.A
Samsung Electronics
Electrical Parts List
Loc. No.
..2 RY701
..2 RY702
..2
...3
Code No.
Description ; Specification
2001-001185
2001-001185
AA98-60002G
0202-000187
Remark
R-CARBON(S);750OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);750OHM,5%,1/2W,AA,TP,2.4X6.4
ASSY-SUB,PART;SCV11D,A/V BOARD,-,ALL
SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
S.N.A
S.N.A
ASSY-SPEAKER
1
*
..2
..2
..2
AA96-00149A ASSY-SPEAKER;-,-,16 OHM,2.5W,3001-001015
S.N.A
0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
3001-001015 SPEAKER;2.5W,16ohm,88dB,150Hz
AA39-20501A LEAD CONNECTOR-ASSY;,3(2),67096-003,REC,
S.N.A
ASSY-POWER,CORD
! 1
*
AA96-20124A ASSY-POWER,CORD;-,EP2/YES(AU),H/C250,KJP
ASSY-CHASSIS,PART
1
*
AA90-00037B ASSY-CHASSIS,PART;PAL SESA,14C5
..2 PCB+HC AA60-10008A SCREW-TAPPING;-,SWRCH18A,M3,L10,TH,+,-,..2
AA61-20163A HOLDER-CHASSIS;-,T3350,ABS,V0,GRY,-
S.N.A
S.N.A
ASSY CABINET
1
*
AA90-00126D ASSY CABINET;14A5 MASTER,TB14A53X/RAD
..2
..2
..2
..2
..2
..2
..2
..2
..2
..2
AV+CF
CB+CF
CB+FD
CRT
MST+CF
6003-000333
6002-000514
6002-000514
AA60-10050R
6003-000333
AA65-30016A
AA60-00091A
AA64-00111A
AA64-31340C
AA65-30008A
SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWR
SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWR
SCREW-ASSY;-,SWRCH18A,M5,L31.5,HH,+,WC,SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
CLAMP-D,COIL;-,NYLON-66,V0,-,NTR,DADH-36
SPACER-FELT;-,FELT,150X10,-,-,BLK,T0.35,
INLAY-BACK,AV;14.20A5,21B5,-,PS SHEET,T0
CABINET-BACK;-,14A5,C5,SEA ,HIPS,V0,BLK
CLAMP-CORD;-,PE,HB,-,BLK,-
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
ASSY CABINET FRONT
1
*
AA91-00184D ASSY CABINET FRONT;-,14A5 MASTER,BK708P
..2 IND+CF 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
S.N.A
..2 KF+CF 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR
S.N.A
..2 MASTER AA61-60003Q SPRING-CS;-,SUS304,0.5,OD8,H10,N5,-,-,..2
AA64-70127F BADGE-BRAND;AL,SAMSUNG,SILVER,L40,R800,N S.N.A
..2
AA64-31339P CABINET FRONT;14A5,C5,BK708P HITRON EL,H
...3
AA61-40010A BOSS-WING;-,HIPS,-,-,-,NTR,HB
..2
AA64-00051E PANEL CONTROL;14A5 MAST,HIPS,-,V0,BLK,-,
..2
AA64-00038A KNOB-MASTER;-,TVCR 14,20,M/S BK-708P,A
..2
AA64-00018A WINDOW-REMOCON;-,TVN-502V,-,PC,VIOLET,-,
..2
AA64-00012A INDICATOR-LED;-,TVN-502V,-,PC,-,CLEAR,..2
AA64-00011A KNOB-FAMILY;-,TVN-502V,BK-708P ,ABS,HB,B
ASSY M/DECK
1
*
AA94-02353A ASSY M/DECK;M-520BK/XSA-X,2HD,-,14,HQ,C
..2
AA90-00366A ASSY FRAME;PAL TTX(X) EL 14,TS-DECK
...3 CFT+FD 6003-001022 SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR
...3 DE+FD 6002-000522 SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR
...3 FD+PCB 6003-001022 SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR
...3
AA64-01013Y DOOR-HOUSING;TVCR,ABS,HB,BLK,-,-,BK708P
...3
AA60-00091A SPACER-FELT;-,FELT,150X10,-,-,BLK,T0.35,
...3
AA63-40313A SHIELD-CASE,B;TVN334V,SPTE,T0.3,...3
AA63-00036A COVER-FRAME TOP ASSY;-,TS-DECK,PAL,SECC,
Samsung Electronics
S.N.A
S.N.A
S.N.A
Loc. No.
....4
....4
...3
...3
..2
..2
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
...3
....4
....4
....4
...3
....4
....4
....4
...3
...3
....4
....4
...3
....4
....4
...3
...3
...3
...3
....4
....4
...3
...3
...3
...3
...3
....4
...3
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
Code No.
Description ; Specification
Remark
AA63-00012A COVER-FRAME,T;-,TVCR,PAL,SECC,-,-,-,AA63-40301A SHIELD-PLATE;-,S30,T0.5,-,TF531
AA61-00050A SPRING-DOOR;-,SUS304,-,-,-,-,0.5,OD6,H9.
AA61-00004B FRAME-DECK;TVCR,HIPS,-,V0,BLK,-,-,-,AA91-00308A ASSY DECK;-,2HD,PAL,BON,SVTW-M2P/BON
S.N.A
AA95-00456X ASSY-PCB,M/DECK;-,2HD,C15C,PAL,-,TS
CNM101 AA39-20159D LEAD CONNECTOR-ASSY;,12P,YBNH025-12,6709
CNM102 AA39-20071D LEAD CONNECTOR-ASSY;,12P,YBNH025-12,6709
CNM301 3708-000395 CONNECTOR-FPC/FC/PIC;8P,1.25MM,STRAIGHT,
CNM302 3708-001053 CONNECTOR-FPC/FC/PIC;7P,1.25MM,STRAIGHT,
CNM303 3710-000405 CONNECTOR-SOCKET;2P,2R,2.5MM,-,
CNM51A3809-001111 CABLE-FLAT;30V,80C,130mm,7P,1.25mm,UL289
CNM601 AA39-20603A LEAD CONNECTOR-ASSY;,2P,GIL-S-2S-S2C2-S,
CNM602 3708-001131 CONNECTOR-FPC/FC/PIC;5P,1.25mm,STRAIGHT,
CNM6033711-003749 CONNECTOR-HEADER;BOX,8P,2R,2mm,STRAIGHT,
CNM64A3809-001112 CABLE-FLAT;30V,80C,130mm,5P,1.25mm,UL289
FLM301 AA26-10006C TRANS-IF;-,7MF,BIAS,2.4MH,7MM,-,65.3KHZ
GPM001 AA63-40311A GROUND-PLATE,POB;-,PBS,T0.3,TVN334V,S.N.A
ICM101 AA96-00111L ASSY-H/S;-,-,AA62-30013L,KA78R12,S.N.A
1203-000165 IC-POSI.ADJUST REG.;78R12,TO-220,3P,-,-,
6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
S.N.A
AA62-30013L HEATSINK-ES;-,-,-,-,44/22,-,WHT,-,-,-,S.N.A
ICM102 AA96-50152D ASSY-H/S;-,MAIN,AA62-30012A,KA7809,S.N.A
1203-000298 IC-POSI.FIXED REG.;7809,TO-220,3P,-,PLAS
6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
S.N.A
AA62-30012A HEAT SINK-ES;-,A6063 EXTR,-,-,T0220,-,-,
S.N.A
ICM602 1003-001162 IC-MOTOR DRIVER;KA3082,SIP,10PIN,25MIL,D
LDM601 AA91-60318A ASSY-HOLDER,LED;-,ABS,HB,BLK,IR LED,TS-D
0601-001303 LED-IR;SIDE-VIEW,2.5mm,75mW,6V,950nm,
AA61-00003A HOLDER-LED;-,TVN-502V,-,HB,BLK,LDM602 AA91-60317A ASSY-GUIDE,LED;-,ABS,V0,BLK,RED LED 03,T
0601-000385 LED;ROUND,RED,3mm,700nm
AA61-00006A GUIDE-LED;TVCR ,ABS,-,-,-,BLK,V0
PTM601 0604-001122 PHOTO-INTERRUPTER;TR,0.065%,150mW,DIP-4,
PTM602 0604-001122 PHOTO-INTERRUPTER;TR,0.065%,150mW,DIP-4,
REM601 AA59-60003V MODULE-REMOCON;-,SRV-18,38KHZ,940NM,MESH
SM601 AA91-60319A ASSY-HOLDER,SENSOR;-,ABS,HB,BLK,TR LED,T
0603-001011 PHOTO-TR;NPN,35V,6V,50mA,75mW,BK
AA61-00005A HOLDER-SENSOR;-,TVN-502V,-,HB,BLK,SM602 AA91-60319A ASSY-HOLDER,SENSOR;-,ABS,HB,BLK,TR LED,T
SWM610AA34-20001ASWITCH-MODE;1,25x14.6x29.8mm,BK,DC5V
SWM611AA34-40001ASWITCH-REC.;1EA,37.5x14.4mm,BK,DC5V
XTM602 2801-003224 CRYSTAL-UNIT;32.768KHZ,20PPM,28-AAY,12.5
AA98-60005X ASSY-SUB,PART;SCV11F,DECK,-,ALL
S.N.A
0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
S.N.A
AA99-20072H ASSY-PCB SUB,AUTO; AA95-00456X ,V
S.N.A
CM101 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5
CM102 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5
CM103 2401-000832 C-AL;220uF,20%,25V,GP,TP,8x11.5,5
CM104 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
CM105 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
CM106 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
CM107 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
CM109 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
CM110 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
CM111 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
CM112 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
CM113 2401-000832 C-AL;220uF,20%,25V,GP,TP,8x11.5,5
CM114 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
CM301 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
CM303 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
CM304 2401-000426 C-AL;10uF,20%,16V,GP,TP,3.5x5,5
CM305 2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm,
CM306 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
CM307 2401-001250 C-AL;4.7uF,20%,35V,GP,TP,4x5,5
CM308 2401-000665 C-AL;2.2uF,20%,50V,GP,TP,3.5x5,5
CM309 2305-000427 C-FILM,MPEF;47nF,5%,100V,TP,7.5x12.5x3.5
CM310 2401-000590 C-AL;1uF,20%,50V,GP,TP,3x5,5
CM311 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
CM312 2401-002291 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
CM313 2202-000127 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
CM314 2202-000216 C-CERAMIC,MLC-AXIAL;27pF,5%,50V,SL,TP,3.
CM315 2201-002031 C-CERAMIC,DISC;0.005nF,0.5pF,50V,NP0,TP,
CM316 2202-000862 C-CERAMIC,MLC-AXIAL;390pF,10%,50V,Y5P,TP
CM317 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5
CM318 2202-000162 C-CERAMIC,MLC-AXIAL;15pF,5%,50V,SL,TP,3.
CM319 2201-000345 C-CERAMIC,DISC;0.2nF,5%,50V,SL,TP,7x3,5
8-5
Electrical Parts List
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
8-6
CM320
CM321
CM322
CM323
CM324
CM325
CM326
CM327
CM328
CM329
CM331
CM332
CM333
CM334
CM335
CM336
CM337
CM338
CM339
CM340
CM341
CM342
CM343
CM344
CM345
CM346
CM347
CM348
CM349
CM350
CM351
CM352
CM353
CM354
CM355
CM356
CM357
CM358
CM359
CM360
CM361
CM362
CM363
CM364
CM365
CM367
CM368
CM370
CM371
CM372
CM373
CM377
CM378
CM379
CM383
CM384
CM390
CM391
CM392
CM393
CM394
CM395
CM601
CM602
CM603
CM604
CM605
CM606
CM607
CM608
CM609
CM610
CM611
CM612
CM613
CM614
CM615
Code No.
Description ; Specification
2202-000849
2202-000127
2401-002463
2401-000426
2401-000914
2202-000796
2401-001333
2202-000632
2401-002235
2202-000632
2401-000603
2401-000426
2401-000590
2202-000127
2202-000127
2202-000127
2202-000127
2202-000127
2202-000632
2401-002291
2202-000127
2202-000632
2401-002291
2401-000590
2202-002055
2401-000590
2202-000807
2401-000603
2202-000127
2202-002055
2202-000807
2202-000632
2401-002144
2202-000632
2401-000914
2401-002462
2401-002619
2202-000632
2201-000611
2201-000611
2301-000383
2301-000301
2301-000301
2301-000314
2401-000027
2202-000632
2301-000175
2301-000254
2301-000301
2301-000160
2401-002144
2202-000127
2202-000127
2202-000127
2202-000830
2202-000205
2202-000632
2202-000632
2401-000603
2202-000632
2202-000632
2202-000279
2202-000806
2301-000310
2301-000310
2301-000224
2401-002291
2202-000632
2202-000205
2202-000205
2202-000205
2202-000205
2401-000590
2202-000127
2202-000127
2401-001250
2202-000127
C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3.
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;470uF,20%,16V,GP,TP,8x11.5,5
C-AL;10uF,20%,16V,GP,TP,3.5x5,5
C-AL;22uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;10uF,20%,16V,GP,TP,3.5x5,5
C-AL;1uF,20%,50V,GP,TP,3x5,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;47uF,20%,16V,GP,TP,6.3x5,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;47uF,20%,16V,GP,TP,6.3x5,5
C-AL;1uF,20%,50V,GP,TP,3x5,5
C-CERAMIC,MLC-AXIAL;47nF,+80-20%,50V,Y5V
C-AL;1uF,20%,50V,GP,TP,3x5,5
C-CERAMIC,MLC-AXIAL;22nF,+80-20%,25V,Y5V
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;47nF,+80-20%,50V,Y5V
C-CERAMIC,MLC-AXIAL;22nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;22uF,20%,16V,GP,TP,5x11,5
C-AL;33uF,20%,16V,GP,TP,5x11,5
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,DISC;0.056nF,5%,50V,NP0,TP,7x3
C-CERAMIC,DISC;0.056nF,5%,50V,NP0,TP,7x3
C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
C-FILM,PEF;6.8nF,5%,50V,TP,6.5X5.5X3.0X5
C-FILM,PEF;6.8nF,5%,50V,TP,6.5X5.5X3.0X5
C-FILM,PEF;8.2nF,5%,50V,TP,6.5x3.0x5.5mm
C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-FILM,PEF;15nF,5%,50V,TP,7.1x3.5x13mm,5
C-FILM,PEF;39nF,5%,50V,TP,7.5x3.5x6.5mm,
C-FILM,PEF;6.8nF,5%,50V,TP,6.5X5.5X3.0X5
C-FILM,PEF;12nF,5%,50V,TP,11.0x6.0x9.0mm
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;82pF,10%,50V,Y5P,TP,
C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.
C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP
C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,
C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5
C-AL;47uF,20%,16V,GP,TP,6.3x5,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C-AL;1uF,20%,50V,GP,TP,3x5,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;4.7uF,20%,35V,GP,TP,4x5,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
Remark
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
CM616
CM617
CM621
CM622
CM623
CM624
CM627
CM628
CM629
CM630
CM631
CM632
CM633
CM634
CM635
CM636
CM637
CM638
CM639
CM640
CM641
CM642
CM645
CM647
CM649
CM651
DM102
DM104
DM107
DM108
DM109
DM110
DM111
DM112
DM305
DM601
DM602
DM606
DM607
DM608
DM609
DM610
DM611
DM714
ICM301
ICM601
ICM603
JM224
LM101
LM301
LM302
LM303
LM304
LM305
LM306
LM307
LM308
LM309
LM310
LM601
LM602
LM603
LM604
LM605
PCB
QM101
QM102
QM106
QM107
QM301
QM302
QM304
QM305
QM306
QM308
QM311
QM312
Code No.
Description ; Specification
2401-002619
2401-002619
2401-000302
2202-000127
2401-000302
2202-000127
2401-002009
2202-000127
2202-000632
2202-000632
2202-000632
2401-002009
2202-000632
2202-000127
2202-000127
2202-000183
2202-000183
2202-000263
2401-000914
2202-000121
2401-000302
2202-000632
2202-000632
2401-002619
2202-000632
2202-000632
0402-000132
0402-000132
0401-000005
0402-000132
0401-000005
0402-000132
0402-000132
0402-000132
0401-000005
0401-000005
0401-000005
0402-000132
0401-000005
0401-000005
0401-000005
0402-000132
0401-000005
0401-000005
1204-001649
AA09-00049A
1203-000642
2701-000211
2701-000002
2701-000002
2701-000207
2701-000118
2701-000002
2701-000002
2701-000002
2701-000002
2702-000120
2701-000112
2701-000180
2701-000002
2701-000002
2701-000002
2701-000002
2701-000002
AA41-00143B
0501-000316
0504-000116
0501-000362
0501-000362
0501-000398
0501-000398
0501-000303
0501-000303
0501-000398
0501-000398
0501-000303
0501-000010
Remark
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;100uF,20%,16V,GP,TP,6.3x7,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;100uF,20%,16V,GP,TP,6.3x7,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP
C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP
C-CERAMIC,MLC-AXIAL;470pF,10%,50V,Y5P,TP
C-AL;22uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-AL;47uF,20%,25V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
IC-VIDEO PROCESS;LA71598M,QFP,100P,-,PLA
IC-MCU;UPD784927GF-160-BA,SNM-734MD,S
IC-RESET;572,TO-92,3P,-,PLASTIC,2.35/2.
INDUCTOR-AXIAL;68uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm
INDUCTOR-AXIAL;120uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-RADIAL;15mH,5%,6.2x7.4mm
INDUCTOR-AXIAL;100uH,10%,3x7mm
INDUCTOR-AXIAL;33uH,5%,2.5x3.4mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm
PCB-DECK MAIN;C15C,1L,FR-1,330x245x1.6T,
TR-SMALL SIGNAL;KSA928A-Y,PNP,1000mW,TOTR-DIGITAL;KSR1001,NPN,300MW,4.7K/4.7K,T
TR-SMALL SIGNAL;KSA2328A-Y,NPN,1W,TO-92L
TR-SMALL SIGNAL;KSA2328A-Y,NPN,1W,TO-92L
TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
TR-SMALL SIGNAL;KSA733,PNP,250mW,TO-92,T
TR-SMALL SIGNAL;KSA733,PNP,250mW,TO-92,T
TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
TR-SMALL SIGNAL;KSA733,PNP,250mW,TO-92,T
TR-SMALL SIGNAL;KSC1008,NPN,800mW,TO-92,
S.N.A
Samsung Electronics
Electrical Parts List
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
QM313
QM314
QM315
QM317
QM603
QM604
QM605
RM101
RM102
RM103
RM106
RM107
RM108
RM302
RM303
RM304
RM305
RM306
RM307
RM310
RM312
RM313
RM314
RM315
RM316
RM317
RM318
RM319
RM323
RM324
RM325
RM327
RM328
RM329
RM330
RM331
RM333
RM334
RM335
RM338
RM339
RM340
RM341
RM344
RM345
RM346
RM347
RM348
RM349
RM350
RM351
RM352
RM353
RM354
RM356
RM357
RM358
RM359
RM360
RM361
RM362
RM363
RM365
RM369
RM370
RM371
RM372
RM373
RM377
RM378
RM508
RM509
RM514
RM515
RM601
RM602
RM603
Code No.
0501-000442
0501-000442
0501-000303
0501-000389
0504-000118
0504-000118
0504-000118
2001-000273
2001-001122
2001-000449
2001-000449
2001-001107
2001-000674
2001-000812
2001-000331
2001-000645
2001-000362
2001-000660
2001-000241
2001-000429
2001-000429
2001-000472
2001-000924
2001-000515
2001-000221
2001-000429
2001-000003
2001-000003
2001-000241
2001-000734
2001-000515
2001-000281
2001-000800
2001-000969
2001-000037
2001-000723
2001-000429
2001-000472
2001-000232
2001-000977
2001-000258
2001-000449
2001-000429
2001-000454
2001-000734
2001-000472
2001-000832
2001-000832
2001-000221
2001-000947
2001-000812
2001-000006
2001-000904
2001-000522
2001-000405
2001-000780
2001-000258
2001-000458
2001-000290
2001-000429
2001-000429
2001-000522
2001-000734
2001-000800
2001-000008
2001-001000
2001-000515
2001-000812
2001-000273
2001-000995
2001-000766
2001-000947
2001-000766
2001-000947
2001-000554
2001-000522
2001-000864
Samsung Electronics
Description ; Specification
Remark
TR-SMALL SIGNAL;KTC3203-Y,NPN,400mW,T0-9
TR-SMALL SIGNAL;KTC3203-Y,NPN,400mW,T0-9
TR-SMALL SIGNAL;KSA733,PNP,250mW,TO-92,T
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
TR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TOTR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TOTR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TOR-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);3.9KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);220ohm,5%,1/2W,AA,TP,2.4x6.4
R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;330KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;150OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;5.1KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);330OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;4.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;8.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.2MOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.4KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;620OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;180OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.2OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;5.1KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;43KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;43KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
RM604
RM605
RM606
RM607
RM608
RM609
RM610
RM611
RM612
RM613
RM614
RM615
RM616
RM618
RM619
RM620
RM624
RM626
RM628
RM629
RM630
RM631
RM632
RM633
RM634
RM635
RM636
RM637
RM638
RM639
RM640
RM641
RM642
RM643
RM644
RM647
RM648
RM649
RM650
RM651
RM652
RM653
RM654
RM655
RM656
RM657
RM660
RM661
RM663
RM664
RM665
RM666
RM667
RM668
RM669
RM670
RM671
RM674
RM678
RM679
RM680
RM681
RM682
RM683
RM684
RM685
RM686
RM687
RM688
RM689
RM690
RM691
RM692
RM693
RM694
RM696
RM697
Code No.
2001-000660
2001-000429
2001-000864
2001-000864
2001-000429
2001-000429
2001-000010
2001-000832
2001-000009
2001-000429
2001-000290
2001-000290
2001-000660
2001-000786
2001-000281
2001-000281
2001-000429
2001-000429
2001-000429
2001-000429
2003-002129
2001-001077
2001-001077
2001-001077
2001-000734
2001-000734
2001-000734
2001-000290
2001-000429
2001-000290
2001-000633
2001-000118
2001-000522
2001-000429
2001-000010
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000005
2001-000005
2001-000290
2001-000429
2001-000522
2001-000554
2001-000281
2001-000281
2001-000281
2001-000281
2001-000281
2001-000281
2001-000539
2001-000290
2001-000331
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000290
2001-000290
Description ; Specification
Remark
R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;68KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;20KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);3.9ohm,5%,2W,AF,TP,3.9x
R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;30KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);180OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;68KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;24KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
8-7
Electrical Parts List
Loc. No.
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
Code No.
Description ; Specification
RM698 2001-000290
RM699 2001-000290
SWM601 3404-000244
SWM602 3404-000244
SWM603 3404-000244
SWM604 3404-000244
SWM605 3404-000244
SWM606 3404-000244
SWM607 3404-000244
SWM608 3404-000244
SWM609 3404-000244
SWM612 3404-000244
VRM601 2103-000669
XTM301 2801-000277
XTM601 2801-003750
ZDM101 0403-001373
ZDM102 0403-000720
ZDM601 0403-001211
Remark
Loc. No.
Code No.
Description ; Specification
Remark
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
VR-SEMI;10Kohm,25%,1/5W,TOP
CRYSTAL-UNIT;4.433619MHz,8ppm,28-AAM,S,1
CRYSTAL-UNIT;8MHZ,30PPM,28-AAA,22PF,80OH
DIODE-ZENER;MTZJ5.1A,4.81V-5.07V,500mW,D
DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D
ASSY ACCESSORY
1
*
..2 A/R
..2
..2
..2
AA94-03758A ASSY ACCESSORY;TB14A53X/RAD,C15C,NEWZEAL
AA42-00003A
AA68-00897A
AA68-00711A
AA26-90001C
ANT ROD;-,3S,720mm,ABS,UL/CSA,MANUAL USERS;-,-,ENG,ENG,W/P100(G),2,-,B
CARD WARRANTY;ALL,W/P100G,-,-,-,-,TRANS-MATCHING;-,300ohm/75ohm,PAL,40-890
S.N.A
REMOCON
1
8-8
*
AA59-00107J REMOCON;-,TM48,SPM738EE,39,L/GRAY,S/S,
Samsung Electronics
Exploded View & Parts List
7-2 Mechanical Parts (Top Side)
Loc. No
G001
K490
K502
K530
G530
G555
B473
G450
B474
G510
G420
G680
G480
(OPTIONAL)
K546
K250
K240
(OPTIONAL)
K248
B575
G681
B410
K350
K110
B440
K182
B448
K340
K330
B452
G546
K470
K140
K188
G527
G520
G060
7-2
G070
Parts No.
Description ; Specification
B410
AC31-00012A
MOTOR-LOADING ASSY;-,TS-10,-,-,-,-,-,-,-
B440
AC60-10515A
SCREW-MACHINE;-,PH,+,-,M3,L3,ZPC,-,YEL
B448
AC66-00008A
GEAR-WORM WHEEL;TS-10,POM,0.8,40,-,NAT,3
B452
AC66-00011A
GEAR-FL CAM;TS-10,POM,0.8,59,-,BLK,48.48
B473
AC61-00105A
SPRING-PINCH DRIVE;TS-10,SUS304-WPB,-,-,
B474
AC61-30180A
PLATE-JOINT;-,SECC20/20,T0.8,-,X-9
B575
AC47-00002A
DAMPER-CAPSTAN;TS-10,POM,-,-,BLACK
G001
AC97-01212A
ASSY-CYLINDER;PALCTS10,4HD/DLC
G060
6006-001092
SCREW-ASS? MACH;WS,PH,+,M3.0,L6.0,ZPC(Y
G070
AC61-00161A
PLATE-GROUND DECK;TS-10,SPTE,T0.3,-
G420
AC66-80142A
SLIDER-SUPPLY ASSY;-,X-9(TS),-,-,-,X-9
G450
AC66-80141A
SLIDER-TAKE UP ASSY;-,X-9(TS),-,-,-,X-9
G480
AC33-00009A
HEAD-ACE ASS?;-,PPS,TS-10,-,-
G510
6006-001075
SCREW-ASS? TAPT;WSP,PH,+,M2.6,L5.0,ZPC(
G520
AC66-00033A
LEVER-#9 GUIDE ASS?;TS-10,-,-,-,-,-,-,-
G527
AC61-60553A
SPRING-#9 GUIDE;-,ES,SUS304-WPB,OD3.1,0.
G530
AC33-00007A
HEAD-FE;-,-,HVFHPOO43A,-,-
G546
AC66-00005A
LEVER-FL DOOR;TS-10,POM,-,-,-,-,NAT,-
G555
AC66-00032A
LEVER-UNIT PINCH ASS?;TS-10,-,-,-,-,-,-
G680
AC66-00046A
LEVER-HEAD CLEANER ASS?;TS-10,POM+URETH
G681
AC61-50686A
SLEEVE-HEAD CLEANER;-,POM,-,-,-,-,-,-,TS
K110
AC66-10267A
REEL-DISK S;X-9,POM,-,-,-,-,-,-
K140
AC66-10268A
REEL-DISK T;X-9,POM,-,-,-,-,-,-
K182
AC66-30524A
LEVER-IDLER;-,POM,-,-,-,-,-,-
K188
AC66-00039A
GEAR-IDLE;TS-10,PET K3372,0.5,-,-,NTR,28
K240
AC66-00035A
LEVER-TENSION ASS?;TS-10,SECC E20/20+SU
K248
AC61-00107A
SPRING-TENSION LEVER;TS-10,SUS304-WPB,-,
K250
AC69-00104A
BAND-BRAKE ASS?;TS-10,-,-,-,-,-,-
K330
AC66-30550A
LEVER-S.BRAKE ASSY;-,POM+SUS,-,-,-,X-9
K340
AC66-30549A
LEVER-T.BRAKE ASSY;-,POM+SUS,-,-,-,X-9
K350
AC61-00106A
SPRING-BRAKE;TS-10,SUS304-WPB,-,-,-,-,-,
K470
AC66-00020A
SLIDER-FL DRIVE;TS-10,SECC E20/20,1.0,-,
K490
AC61-00120A
HOLDER-FL CASS. ASS?;TS-10,-,-,-,-,-
K502
AC61-60561A
SPRING-FL.LEVER-LR;-,ES,SUS304 WPB,PI2.7
K530
AC66-00034A
LEVER-FL ARM ASS?;TS-10,-,-,-,-,-,-,-
K546
AC61-50658A
GUIDE-CASS. DOOR;X-9,POM,-,NTR,-,-
Remark
Samsung Electronics
Exploded View & Parts List
7-3 Mechanical Parts (Bottom Side)
Loc. No
G542
B462
B456
B560
B460
Description ; Specification
B456
AC66-00009A
GEAR-JOINT 1;TS-10,POM,1.5,17.5(22),-,NA
B458
AC66-00012A
GEAR-JOINT 2;TS-10,POM,1.0,23,-,BLK,24.6
B460
AC61-00090A
BRACKET-GEAR;TS-10,0.8,-,-
B462
AC60-10517A
SCREW-TAP TITE;-,PH,+,-,M2.6,L5,ZPC,-,YE
B464
AC66-00019A
SLIDER-CAM;TS-10,SECC E20/20,1.2,-,-,-,-
B468
AC66-00017A
LEVER-PINCH DRIVE;TS-10,SECC E20/20,1.0
B478
AC66-00016A
LEVER-TENSION DRIVE;TS-10,SECC E20/20,1
B484
AC66-00030A
GEAR-LOADING DR. ASS?;TS-10,POM+SWPB,-,
B488
AC66-00023A
LEVER-S LOADING;TS-10,POM,-,-,-,-,NAT,-
B489
AC66-00021A
LINK-LOADING S;TS-10,SECC E20/20,0.8,-,-
B500
AC66-00024A
LEVER-T LOADING;TS-10,POM,-,-,-,-,NAT,-
B501
AC66-00022A
LINK-LOADING T;TS-10,SECC E20/20,0.8,-,-
B560
AC31-00010A
MOTOR-CAPSTAN;-,SANKYO,-,-
B570
AC60-10514A
SCREW-CAPSTAN;-,PH,+,M2.6,L6,-
G542
AC66-60051A
BELT-PULLEY;-,5CM-70,2 * 2,-,71.3,-,X-9
K200
AC61-21012A
HOLDER-CLUTCH ASSY;-,-,-,-,-,X-9
K221
AC66-20581A
GEAR-CENTER ASSY;-,POM,M=O.5,-,HIGHT T.,
K222
AC60-30306A
WASHER-SLIT;-,-,ID2.1,OD5.0,T0.5,-,POLYS
K225
AC66-00006A
LEVER-UP DOWN;TS-10,POM,-,-,-,-,NAT,-
Remark
B500
B458
B464
Parts No.
B501
B484
B488
B489
B468
K222
K200
K225
K221
B478
B570
Samsung Electronics
7-3
Troubleshooting
6-2 No Power (No LED On)
Yes
Check CN102
Retouch CN102 or
Replace CN102
No
Check IC901 #64
Yes
Check IC804
Check IC901 #23, #24
No
No
No
Yes
Check another I2C
Bus Line.
Check after Bus
Line Open
Check IC801
No
Replace
Yes
Check Q801
No
Replace
Yes
Check D801~D805
Check IC901 #28~31
Yes
No
No
Replace
IC901
6-2
Check/Replace
D801~D805
Samsung Electronics
Troubleshooting
6-3 No RF Picture / Sound
No
Check IC901 #23, #24
Yes
Yes
Check D834 "H" and
IC807
Check Another I2C
bus line
No
Check After
bus line open
No
Replace
Yes
Check IC201 #12, #37
No
Replace
Yes
Check Q401, Q402
No
Replace
Yes
Check
IC201 #40, #41,
R416, R408, R409,
D401, D402
No
Replace
Samsung Electronics
6-3
Troubleshooting
6-4 No Picture (Sound OK)
1
Check the Brightness, Contrast and Color adjustments
2. Check: AV Picture, Video Playback
3. See Video Block Diagram
6-5 No Sound (Picture OK)
1. Check the Volume adjustment level.
2. Check AV Video, Sound Playback
3. See Audio Block Diagram
6-6 RF Weak Signal (Playback, AV Mode OK)
1. Check Tuner (TU01S) B+. Check: 9V (IC807)
33V (DZ803). Check 5V (IC902S)
2. Pre AMP (HC001S), B+. Check: 9V (IC807)
6-7 Recording Defect
1. CN101 Check : Retouch
2. 2nd Tuner (TU02S) B+. Check : 33V(DZ803)
5V (IC808)
3. 2nd If : Check 9V (IC806), Video out, Audio out
4. Video Defect : IC701 Check
5. Audio Defect : IC701 Check
6. Standby Recording Defect, IC901S #5 Line: Check (D834, IC804, IC807, IC806)
7. VPS (PDC) Recording Defect: Check IC901S, #4
6-4
Samsung Electronics
Troubleshooting
6-8 No Color
1. Check the Color Adjustment level
2. Check the Sandcastle Pulse Line : IC201S #41
3. Check the R-Y, B-Y Line : IC201S #29~#32
4. Check crystal : X202 (4.43361MHz)
6-9 No Vertical SCAN
1. Check R410, D404
2. Check IC301, #7
3. Check IC201S #46, #47 Line
4. Check DY Connector
6-10 Horizontal Size
1. Check C402 , C403 , L401 , L404
6-11 On-Screen Display Missing
1. Check IC901S #2
(D905, Q901, DZ901)
2. Check IC901S #37 (R949, IC903)
Samsung Electronics
6-5
Troubleshooting
6-12 Play Mode Inoperative
EE-VIDEO
No
See Video Missing
In EE Mode
No
See
(Regulator Inoperative)
Yes
Insert a Cassette
Tape Recorded by
Another VCR and
Press Play Button
Yes
Play
Indication in
Display
Yes
Mechanism
Operation
Yes
PB-Video
No
See
(Mechanism Does Not
Operate in Play Mode)
Does Not Operate or
Operates but Stops Soon
No
See
Video Missing in
Play Mode
Yes
See (PB Audio)
Audio Missing in
Play Mode
6-6
Samsung Electronics
Troubleshooting
6-13 Mechanism Does Not Operate In Play Mode
Mechanism Does Not
Operate In Play Mode
Place VCR
Power On
Load a Tape and
Press Play Button
Yes
Tape Loading
Operation
(Load)
ICM601-38 : HIGH
ICM601-39 : LOW
No
No
Moter B+
ICM602- 2,10
No
Motor B+ Line
Yes or VCR Stops Soon
Replace ICM601
(S.End Sensor)
ICM601-77,76
Low
Replace ICM602
Check Tape
High
Cylinder
Rotation
No
See
(Cylinder Does
Not Rotate)
No
Check CYL FG.
ICM601-93
No
See
(Capstan Does
Not Rotate)
OK but VCR Stops Soon
(SW 25Hz)
ICM601-24
Yes
Capstan
Rotation
Yes
S, T Reel
ICM601-99,98
DC
PTM601, PTM602,
Supply/Take Up Reel Sensor
PTM601, PTM602
Yes
Prog, SW State
ICM601-63,64,65
No
Deck Loading Motor
Mechanism
Yes
Replace ICM601
Samsung Electronics
6-7
Troubleshooting
6-14 Record Mode Inoperative
No
Play
Operation
See (Play Mode
Inoperative)
Yes
Load VCR With a Blank
Tape and Press Record Button
Yes
Tape Eject
No
Rec SW Logic
ICM601
No
Change Tape Replace
Yes
Replace SWM602
D/ REC (H)
ICM601-66
Low
Check ICM601
High
REC-Video
No
See
(Video Missing in
Record Mode)
Yes
See (Audio Mising in
Record Mode)
6-8
Samsung Electronics
Troubleshooting
6-15 Fast Forward Mode Inoperative
Load VCR With a Tape
and Press F.Fwd Button
Yes
Mechanism
State ICM601-63,
64,65
(STOP)
See
(Mechanism Does Not
Operate In Play Mode)
(STOP)
See
(Capstan Does
Not Rotate)
(F.FWD)
Capstan Motor
Rotation
(Rotate)
Check Mechanism
Samsung Electronics
6-9
Troubleshooting
6-16 Rewind Mode Inoperative
Load VCR With
a Tape
No
See (Fast Forward Mode
Inoperative)
(STOP)
See
(Mechanism Does Not
Operate In Play Mode)
(Rotate)
Press Rewind Button
Yes
Mechanism
State ICM601-63,
64,65
(Rew)
Capstan Motor
Rotation
(STOP)
See ICM601-25
(Rotate)
Check Mechanism
6-10
Samsung Electronics
Troubleshooting
6-17 Rev Search Mode Inoperative
See Play Mode
Inoperative
No
Play
Operation
Yes
Press REV Search Button
Yes
Play Speed
Capstan Speed
Check Mechanism
Replace ICM601
Serach Speed
Noise Bar Locking
Yes
Replace ICM601
Samsung Electronics
No
Rec SW Logic
ICM601
No
Change Tape Replace
Yes
Capstan Motor
6-11
Troubleshooting
6-18 Cassette Loading Mechanism Does Not Operate
Turn the VCR Power
On and Insert a Tape
Tape Loading
Yes
Press Eject Button
No
Check ICM601
6-12
No
Check
(Control Pulse)
ICM601-76,77
No
Check Start/End
Sensor ICM601
No
Check
LM B+ Line
No
Replace
ICM602
Yes
ICM601 - 37
Yes
ICM602-15:LOW
ICM602-13:HIGH
Samsung Electronics
Troubleshooting
6-19 No Servo Lock
Play
C-FG
ICM601-93
No
Check Start/End
Sensor ICM601
No
Check
A/C Head
Yes
CTL Pluse
ICM601-4
Yes
Check CTL
Pulse AC Level (SP, LP
: Over 2Vp-p)
No
Yes
Replace
ICM601
Samsung Electronics
6-13
Troubleshooting
6-20 Capstan Does Not Rotate
9V
CNM603-5
No
Check 12V
at AL15V Line of
Power Supply
No
Check 6V at AL6V
Line of Power Supply
No
Check I-LIMIT.
RM618
No
Check C.M CTL/
RM607, RM604
Yes
AL 5V
CNM603-8
Yes
Place the VCR
In Play Mode
Yes
CNM603-3 2.5V
Yes
2.5V
CNM603-4
No
Check
ICM601
Yes
Check
Capstan Motor
6-14
Samsung Electronics
Troubleshooting
6-21 Drum Does Not Rotate
Check 12V
ICM602-9,21
No
Check 12V at AL15V
of Power Supply
Yes
Place the VCR
In Play Mode
Yes
CYL-Speed
Faster
Check D-FG,D-PG
ICM601-96,97Square Wave
No
Replace
XTM601, CM609, CM610
Slower
(8 MHz)
XTM601
Yes
Check
Cylinder Motor
Samsung Electronics
6-15
Troubleshooting
6-22 Video Missing In Play Mode
No
Video EE Mode
Operation
See (Video Missing
In EE Mode)
Yes
Place VCR
Play Mode
Yes
Video FM In
ICM301-17
No
Check ICM301-18
No
Check
Video Head
Yes
Video
ICM301-20
No
Check
QM302
Yes
Video
ICM301-29
No
Check Video Out Line
Yes
Replace ICM301
6-16
Samsung Electronics
Troubleshooting
6-23 Video Missing In Record Mode
Video EE Mode
Operation
No
TV Switching
Circuit Check
Yes
Place VCR
Record Mode
Yes
FM-Video
ICM301-21
No
Replace ICM301
Yes
FM-Video
ICM301-18
No
Check RM313
Yes
Check Video Head
Samsung Electronics
6-17
Troubleshooting
6-24 Color Missing In Play Mode
FM-ENV
ICM301-61
No
See (Video Missing
In Play Mode)
No
S/W 25Hz
ICM301-11
Yes
Color
ICM301-71
No
Check
ICM601
Yes
Yes
Check
XTM302 : 4.43MHz
No
Change XTM302
No
Yes
Replace ICM301
6-18
Samsung Electronics
Troubleshooting
6-25 Color Missing In Record Mode
(VIdeo In)
Record Mode
No
TV Switching
Circuit Check
No
Check
XTM301 : 4.43MHz
Yes
Color
ICM301-61
No
Replace XTM301
Yes
Yes
FM Signal
ICM301-71
Replace ICM301
No
Check CM351
Yes
Replace ICM301
Samsung Electronics
6-19
Troubleshooting
6-26 Audio Signal Missing in Play Mode (MONO MODE)
Check ICM301
pin75 : 5V
No
Check PC 5V Line
No
Check VCR MICOM
(ICM601- pin27, 28)
No
Check A/C Head and PB EQ
Block (AUDIO HEAD AZIMUTH)
Yes
Check
ICM301 pin23,24
(IC CLK DATA)
Yes
Check ICM301
pin 1 : PB Audio Signal
(Small Signal)
Yes
Check ICM301
pin100 : PB audio signal
(Small Signal)
No
Check CM301
Yes
Check ICM301
pin96 : PB Audio
Signal
No
Replace ICM301
Yes
Check
ICM501 pin54
PB Audio signal
No
Check RM510, RM511, CM528
Yes
Check
ICM501 pin56,58
out put Audio
No
Check ICM501 & Hi-Fi Block
Yes
Check
TV NICAM PART(Sound Block)
6-20
Samsung Electronics
Troubleshooting
6-27 Audio Signal Missing After Recording (MONO MODE)
Check
ICM501 53pin
MONO out
No
Check ICM501 & Hi-Fi PART
No
Yes
Check TV part
NICAM Block (ICM02)
Place VCR in REC Mode
Yes
Check
ICM301 pin 75:
5V
No
Check PC 5V Line
Yes
Check
ICM301 pin7 REC
audio signal
No
Replace ICM301
Yes
Check
FLM501 Pin5 REC
bias signal
No
Check CM370, RM357, RM358
CM371, CM373, CM372,
QM312, RM359
No
Check A/C
Head Assembly
Yes
Check
CNM302 , Pin5
Yes
Replace CNM302
Samsung Electronics
6-21
Troubleshooting
6-28 Audio Missing In Play Mode (Hi-Fi)
PLACE VCR IN PLAY MODE
PB FM
ICM501-18PIN
No
Yes
HI-FI DET
ICM501-17PIN
No
CHECK
ICM501-35PIN : A.HD SW
-20PIN : 5V
-24PIN : GND
RM501.RM502 & CYLINDER ASSY
MONO MODE
Yes
CHECK
ICM501-31, 32PIN : CLOCK, DATA
ICM601-27, 28PIN : CLOCK, DATA
CHECK SIGNAL
ICM501-4,46PIN
Yes
Yes
OUT PUT SIGNAL
ICM501-56, 58PIN
No
CHECK
ICM501-8PIN : A-MUTE
Yes
Yes
Check TV NICAM PART
(Sound Block)
6-22
No
REPLACE ICM501
Samsung Electronics
Troubleshooting
6-29 Audio Missing In Rec Mode (Hi-Fi)
PLACE VCR IN REC MODE
REC - FM
ICM501-18PIN
No
CHECK
ICM501- 31,32;CLOCK DATA
- 14,20,30,36,51;5V
- 60;9V
Yes
REPLACE ICM501
Yes
CHECK
INPUT SIGNAL
ICM501-52,
61 PIN
No
CHECK TV NICAM PART
ICM02
Yes
Check
CYLINDER ASSY
Samsung Electronics
6-23
Troubleshooting
MEMO
6-24
Samsung Electronics
Alignment and Adjustments (Electrical)
5. Alignment and Adjustments (Electrical)
5-1 Preadjustment
5-1-1 Factory Mode
5-1-3 When CRT Is Replaced
1. Do not attempt these adjustments in the Video
Mode.
Make the following adjustments after setting up
purity and convergence:
2. The Factory Mode adjustments are necessary
when either the EEPROM (IC902S) or the CRT
is replaced.
White Balance
Sub-Brightness
Vertical Center
Vertical Size
Horizontal Size
3. Do not tamper with the “Adjustment” screen
of the Factory Mode menu. This screen is
intended only for factory use.
5-1-2 When EEPROM (IC902S) Is Replaced
1. When IC902S is replaced all adjustment data
revert to initial values. It is necessary to reprogram this data.
2. After IC902S is replaced, warm up the TV for
10 seconds.
5-2 Factory (“Service”) Mode
5-2-1 Procedure for the “Adjustment” Mode
1. This mode uses the standard remote control.
The Service Mode is activated by: (1) pressing
the “FACTORY” service key on the local-keyboard, or (2) by entering the following remotecontrol sequence (within 2 seconds):
STAND-BY →DISPLAY →MENU→ MUTE→
POWER ON
2. The “SERVICE (FACTORY)” message will be
displayed. The Service Mode has three components: Adjustment, Option and Reset.
4. Selection sequences for the
PAL/SECAM B/G, L/systems:
down or up key:
AGC>TXP>AFW>SBT>SCT>SCR>STT>RG>
GG>BG>TCT>SC>SL>PVS>PHS>NVS>
NHS>CDL>BKS
5. The VOLUME keys increase or decrease the
adjustment values, (stored in the
non-volatile memory) when Adjustment Mode
is cancelled.
3. Access the Adjustment Mode by pressing the
“VOLUME” keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHANNEL keys (▲,▼).
Samsung Electronics
5-1
Alignment and Adjustments (Electrical)
5-2-2 Main Adjustment Parameters
Table 5-1 Main Adjustment Parameters
OSD ABBREVIATION
RANGE
INITIAL DATA
AUTO GAIN CONTROL
AGC
0 ~ 63 STEP
12
TELETEXT POSMON
TXP
0 ~ 13 STEP
5
AUTO FREQUENCY WINDOW
AFW
0 ~ 01 STEP
00
SUB BRIGHT
SBT
0 ~ 13 STEP
6
SUB CONTRAST
SCT
0 ~ 13 STEP
14" : 06
20/21" : 10
SUB COLOR
SCR
0 ~ 13 STEP
6
SUB TINT
STT
0 ~ 13 STEP
9
RED GAIN
RG
0 ~ 63 STEP
38
GREEN GAIN
GG
0 ~ 63 STEP
32
BLUE GAIN
BG
0 ~ 63 STEP
32
TELETEXT CONTRAST
TCT
0 ~ 38 STEP
00
S-CORRECTION
SC
0 ~ 63 STEP
14/20" : 00
21" : 11
VERTICAL SLOPE
SL
0 ~ 63 STEP
30
PAL VERTICAL SHIFT
PVS
0 ~ 63 STEP
27
PAL HORIZKONTAL SHIFT
PHS
0 ~ 63 STEP
40
NTSC VERTICAL SHIFT
NVS
0 ~ 63 STEP
38
NTSC HORIZONTAL SHIFT
NHS
0 ~ 63 STEP
22
CATHOD DRIVE LEVEL
CDL
0 ~ 07 STEP
14" : 03
20/21" : 06
BLACK STRETCHER
BKS
0 ~ 01 STEP
0
FUNCTION
NOTE :
PVS, PVA, PHS, NVS, NVA,NHS parameters must be aligned using
both the 50 Hz and 60 Hz vertical-field rates.
5-2-3 AGING Mode (Reference Only)
This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the
factory by twice pressing the "FACTORY" key .
Even if the TV power is cut off, the Aging Mode is not cancelled.
The "AGING" marking is displayed on the screen.
The AGING mode is cancelled by repressing the "FACTORY" key.
5-2
Samsung Electronics
Alignment and Adjustments (Electrical)
5-2-4 Option
BIT
ITEM
0
1
AUDIO MODE
NICAM/MONO
2
SYSTEM
CF/CI/CK/CX/CB/CII
3
ATS OPTION
ON/OFF
4
TUNER
2/1
5
G-CODE
SHOWVIEW/VIDEO
PLUS/NONE
6
VPS/PDC
VSP/PDC/NONE
7
AUTO CLOCK
ON/OFF
8
S-MODULATION
54%/80%/100%
5-3 Reset
The Reset Mode is used during factory inspection.
Function Reset : After Factory Reset, the following items revert to their initial values.
1.
2.
3.
4.
5.
6.
7.
Volume
Program Channel
P-STD
Auto Power
NR
Reserved Timer Recording
Skip (Store/Clear)
10
1
CUSTOM
OFF
OFF
ALL CLEAR
ALL CLEAR
Caution : When the EEPROM is replaced, all items revert to their initial values.
Samsung Electronics
5-3
Alignment and Adjustments (Electrical)
5-4 Other Adjustments
5-4-1 General
1. Usually, a color TV needs only slight
touch-up adjustment upon installation.
Check the basic characteristics such as height,
horizontal and vertical sync and focus.
2. The picture should have good black and white
details. There should be no objectionable
color shading; if color shading is present,
perform the purity and convergence adjustments described below.
3. Use the specified test equipment or its
equivalent.
4. Correct impedance matching is essential.
5. Avoid overload. Excessive signal from a sweep
generator might overload the front-end of the
TV. When inserting signal markers, do not
allow the marker generator to distort test
results.
6. Connect the TV only to an AC power source
with voltage and frequency as specified on the
backcover nameplate.
7. Do not attempt to connect or disconnect any
wires while the TV is turned on. Make sure
that the power cord is disconnected before
replacing any parts.
8. To protect against shock hazard, use an
isolation transformer.
5-4-2 Automatic Degaussing
A degaussing coil is mounted around the
picture tube, so that external degaussing after
moving the TV should be unnecessary. But
the receiver must be properly degaussed upon
installation.
The degaussing coil operates for about 1
second after the power is switched ON. If the
set has been moved or turned in a different
direction, disconnect its AC power for at least
10 minutes.
If the chassis or parts of the cabinet become
magnetized, poor color purity will result. If
this happens, use an external degaussing coil.
Slowly move the degaussing coil around the
faceplate of the picture tube and the sides and
front of the receiver. Slowly withdraw the coil
to a distance of about 6 feet before removing
power.
5-4-3 High Voltage Check
CAUTION: There is no high voltage
adjustment on this chassis. The B+ power
supply must be set to +125 volts (Full color
bar input and normal picture level).
1. Connect a digital voltmeter to the second
anode of the picture tube.
2. Turn on the TV. Set the Brightness and
Contrast controls to minimum (zero beam
current).
3. The high voltage should not exceed 27.5KV.
4. Adjust the Brightness and contrast controls to
both extremes. Ensure that the high voltage
does not exceed 27.5KV under any conditions.
5-4
Samsung Electronics
Alignment and Adjustments (Electrical)
5-4-4 FOCUS Adjustment
1. Input a black and white signal.
2. Adjust the tuning control for the clearest picture.
3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
5-4-5 Screen Adjustment
1. Turn to the ACTIVE channel.
2. Adjust the VR screen for a normal picture is (no blooming or flyback line).
3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
5-4-6 Purity Adjustment
1. Warm up the receiver for at least 20 minutes.
2. Plug in the CRT deflection yoke and tighten the clamp screw.
3. Plug the convergence yoke into the CRT and set in as shown in Fig. 5-1.
4. Input a black and white signal.
5. Fully demagnetize the receive by applying an external degaussing coil.
6. Turn the CONTRAST and BRIGHTNESS controls to maximum.
7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide
vertical green belt. (Fig. 5-2).
8. Tighten the convergence yoke.
9. Slowly move the deflection yoke forward, and adjust for the best overall green screen.
10. Temporarily tighten the deflection yoke.
11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity
in each field.
12. Tighten the deflection yoke.
Samsung Electronics
5-5
Alignment and Adjustments (Electrical)
4 Pole Magnet
2 Pole Magnet
6 Pole Magnet
2 POLE
PURITY
Clamper
Screw
ADJUST
(VERTIC
YOKE
CLAMP
SCREW
6 POLE
CONVERGENCE
4 POLE
CONVERGENCE
Fig. 5 -1 Convergence Magnet Assembly
Vertical Green Belt
31m/m
Fig. 5-2 Center Convergence Adjustment
5-4-7 White Balance Adjustment
5-4-7 (A) HIGH-LIGHT ADJUSTMENT
1. Input either a Lion Head or a “pure white” pattern.
2. Warm up the TV for 30 minutes.
3. Check the data in the Service Mode
4. Adjust RG, BG in the Factory Mode.
5-4-7 (B) LOW-LIGHT ADJUSTMENT
1. Automatically accomplished during the high-light adjustment.
5-6
Samsung Electronics
Alignment and Adjustments (Electrical)
5-4-8 Center Convergence Adjustment
1. Warm up the receiver for at least 20 minutes.
2. Adjust the two tabs of the 4 pole magnets to
change the angle between them. Superimpose
the red and blue vertical lines in the center
area of the screen.
3. Adjust the Brightness and Contrast controls for
a well defined picture.
4. Adjust the two-tab pairs of the 4 pole magnets,
and change the angle between them.
Superimpose the red and the blue vertical
lines in the center area of the screen.
BLUE
5. Turn the both tabs at the same time, keeping
the angle constant, and superimpose the red
and blue horizontal line in the center of the
screen.
6. Adjust the two-tab pairs of the 6-pole magnets
to superimpose the red and blue line onto the
green. (Changing the angle affects the vertical
lines, and rotating both magnets affects the
horizontal lines.)
7. Repeat adjustments 2~6, if necessary.
8. Since the 4-pole magnets and 6-pole magnets
interact, the dot movement is complex
(Fig. 5-3).
RED/BLUE
RED
BLUE
RED/BLUE
RED
GREEN
GREEN
6-Pole Magnet Movement
4-Pole Magnet Movement
Fig 5-3 Center Convergence Adjustment
5-4-9 Dual Tuner AFT Adjustment
Test Equipment
1. TV Generator (PM5518,PM5418,ETC.)
2. DC VOLTMETER
1.
2.
3.
Connect DC Voltmeter to AFT terminal of TUNER IF-MODULE.
After selecting P00, input to IF1 terminal of TU002 (38.9 MHz Using PM5518)
_ 0.2V (Using FRANCE : T101, PAL/SCAM B/G,I,D/K : L102)
After selecting P00, set to 2.5V +
Samsung Electronics
5-7
Alignment and Adjustments (Electrical)
5-5 Electrical Adjustment (VCR Section)
5-5-1 Preparation
Electrical adjustments are required after replacing
circuit components and certain mechanical parts.
It is important to perform these adjustment only
after all repairs and replacements have been com
pleted. Also, do not attempt these adjustments
unless the proper equipment is available.
White (100%) signal
White (75%)
signal
Burst Signal
(as fiat as possible)
0.7V
0.3V
0.3V
5-5-2 Required Test Equipment
Horizontal sync signal
1. Color Television or Monitor
2. Oscilloscope : Wide-band, dual-trace, triggered delayed sweep.
3. DC Voltmeter
4. TV CH Generator
5. Attenuator
6. Recording tape. (Blank tape)
7. Pattern Generator : PAL color bar. 100%
White.
Fig. 5-5 Color bar signal of pattern generator
White (100%) signal
White (75%)
signal
0.7V
Burst Signal
(as fiat as possible)
0.3V
0.3V
Horizontal sync signal
Fig. 5-4 Alignment Tape
Fig. 5-6 Color bar signal of alignment tape (75% Color Bars)
5-8
Samsung Electronics
Alignment and Adjustments (Electrical)
5-5-3 PROGRAM SW
SW
POSITION
a
I
b III
II
c
IV d
V
e VI f VII
SW A
SW B
SW C
S/SEN
E/SEN
OFF
ON
OFF
ON
POWER
OFF
LOAD
END
STANDBY
LOAD
START
REV
PLAY
SPT1
SPT2
F/R1
F/R2
FL SW : ON-less than 3.5v / OFF-more than 3.5v (Input to A/D port)
START / END SENSOR : ON-"L", OFF-"H"
: DON'T CARE
PROGRAM S/W
POSITION
TAPE SEN
OPERATION MODE
A
B
C
S
F
STANBY
0
0
0
0
0
Eject
POWER OFF
0
0
0
1
X
Unload POWER OFF
LOADING START
0
0
0
1
X
(Tape loading start point)
LOADING END
1
0 ->1
1
1
X
(Tape loading end point)
REV
1
1
0
X
X
Reverse Picture Ssarch, Reverse SLOW
PLAY
0
1
0
X
X
Play, Rec,F-PS,Still,SLOW,F-ADV
STOP1
0
0
1
1
X
Stop (Play position 5 Min. over)
STOP 2
0
0
1
X
X
(MAIN Break ON MODE)
FF / REW 1
1
0
0
X
X
High speed Rew, Low speed FF
FF / REW 2
0
1
1
X
X
High speed FF, Low speed Rew
X : DON’T CARE
Samsung Electronics
5-9
Alignment and Adjustments (Electrical)
5-5-4 HI-FI AUDIO BLOCK PART LIST
NO
L O C . NO
1
CNM301
C O D E -NO
PARTS
WAFER
WAFER
R
R
R
R
C-AXIAL
C-AXIAL
C-ELEC
C-AXIAL
TR
R
R
WIRE
3
RM509
4
CM384
5
CM392
CM393
QM317
RM377
RM378
JM176
JM242
JM243
ICM501
DM719
CM501
CM502
CM503
CM504
CM505
CM506
CM507
CM508
CM509
CM510
CM511
3708-001165
3708-000391
2001-000947
2001-000878
2001-000947
2001-000878
2202-000830
2202-000205
2401-000603
2202-000632
0501-000389
2001-000273
2001-000995
3812-000219
3812-000219
3812-000219
1204-001422
0401-000005
2401-002009
2401-000632
2401-000455
2401-000598
2401-000922
2401-001250
2301-000383
2401-000922
2401-000914
2401-000232
2401-000445
CM512
CM513
CM514
CM515
CM516
CM517
CM518
CM519
CM520
CM521
2401-000603
2401-001537
2202-000632
2202-000863
2401-000598
2202-000797
2401-000603
2301-000232
2301-000445
2401-000922
2
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
5-10
RM515
WIRE
WIRE
IC
DIODE
C-ELEC
C-AXIAL
C-ELEC
C-ELEC
C-ELEC
C-ELEC
C-AXIAL
C-ELEC
C-ELEC
C-RADIAL
NONE
C-ELEC
C-ELEC
C-AXIAL
C-AXIAL
C-ELEC
C-AXIAL
C-ELEC
C-RADIAL
C-RADIAL
C-ELEC
SPEC
HI FI
MONO
R E MAR K S
6P
10P
7.5K
X
O
X
O
X
O
CHANGE
6.2K
7.5K
6.2K
82pF
22pF
1uF,50V
104
O
X
O
O
X
X
X
X
O
X
X
O
O
O
CHANGE
KSC815-Y
100K
820
JUMPER
JUMPER
JUMPER
LA72634AM
X
X
X
X
X
X
O
O
O
O
O
O
O
O
X
X
MONO
100uF,16V
104
10uF,35V
1uF,50V
22uF,16V
4.7uF,35V
103
22uF,16V
O
X
HI FI
O
O
O
O
X
X
X
X
X
X
X
HI FI
22uF,16V
O
O
O
X
HI FI
X
X
HI FI
1uF,50V
47uF,25V
104
561
1uF,50V
O
X
HI FI
O
O
O
O
HI FI
103
1uF,50V
332,50(P)
O
O
O
X
X
X
X
X
X
X
472,50V(P)
O
O
1N4148
332,50V(P)
472,50V(P)
22uF,16V
O
O
O
CHANGE
CHANGE
CHANGE
CHANGE
CHANGE
CHANGE
MONO
MONO
MONO
MONO
MONO
MONO
MONO
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
X
HI FI
X
HI FI
Samsung Electronics
Alignment and Adjustments (Electrical)
NO
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
L O C . NO
C O D E -NO
PARTS
CM522
CM523
CM524
CM525
CM526
CM527
CM528
CM529
CM530
DM501
JM117
JM155
JM166
JM172
JM186
2301-000383
2401-001250
2401-000922
2401-000590
2202-000632
2401-001250
2401-001250
2202-000632
2401-001513
0402-000132
3812-000219
3812-000219
3812-000219
3812-000219
3812-000219
C-RADIAL
C-ELEC
C-ELEC
JM195
JM240
JM241
JM021
JM013
3812-000219
3812-000219
3812-000219
3812-000219
3812-000219
JM120
JM145
JM152
JM167
JM197
LM501
LM502
LM503
RM501
RM502
RM503
RM504
RM505
RM506
RM507
RM510
RM511
RM512
RM513
Samsung Electronics
HI FI
MONO
103,50V(P)
O
X
HI FI
4.7uF,35V
O
O
X
X
X
X
X
O
O
O
HI FI
O
O
O
O
O
O
X
X
MONO
JUMPER
X
X
X
X
X
X
O
O
JUMPER
O
X
HI FI
WIRE
WIRE
WIRE
WIRE
WIRE
JUMPER
JUMPER
JUMPER
O
X
HI FI
X
X
X
HI FI
JUMPER
O
O
O
JUMPER
O
X
HI FI
3812-000219
3812-000219
3812-000219
WIRE
WIRE
WIRE
JUMPER
JUMPER
JUMPER
O
X
HI FI
O
O
X
X
HI FI
3812-000219
3812-000219
2701-000002
2701-000002
2701-000002
2001-000472
2001-000577
2001-000995
2001-000472
2001-000508
2001-000281
WIRE
WIRE
COIL
COIL
COIL
R
R
R
R
R
R
R
JUMPER
JUMPER
100uH(AL04)
100uH(AL04)
100uH(AL04)
2.7K
2K
820
O
X
HI FI
O
O
O
O
X
X
X
X
X
X
X
HI FI
2001-000281
2001-000660
2001-000290
2001-000786
2001-000786
C-ELEC
C-AXIAL
C-ELEC
C-ELEC
C-ELEC
C-AXIAL
C-ELEC
WIRE
WIRE
WIRE
WIRE
WIRE
R
R
R
R
SPEC
22uF,16V
1uF,50V
104
4.7uF,35V
4.7uF,35V
104
47uF,16V(105)
1N4004
JUMPER
JUMPER
JUMPER
2.7K
O
O
O
R E MAR K S
HI FI
CHANGE
MONO
MONO
MONO
MONO
MONO
MONO
MONO
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
HI FI
X
HI FI
220K
100
O
O
O
X
X
HI FI
100
O
X
HI FI
33K
10K
47K
47K
O
O
O
O
X
X
X
HI FI
X
HI FI
HI FI
HI FI
HI FI
5-11
Alignment and Adjustments (Electrical)
NO
L O C . NO
C O D E -NO
PARTS
75
RM516
2001-000766
R
76
RM517
RM518
RM519
CNM103
2001-000878
2001-000766
2001-000878
AA39-20005B
R
R
R
R
77
78
79
SPEC
HI FI
MONO
O
O
O
O
O
X
HI FI
X
X
X
X
HI FI
43K
6.2K
43K
6.2K
3P
R E MAR K S
HI FI
HI FI
HI FI
5-5-5 SCORPIO PAL OPTION TABLE
NO
L O C . NO
C O D E -NO
SP E C
HI FI
4H D
2H 'D
2H D L P
R E MAR K S
1
0401-000005
0504-000119
2001-001031
0401-000005
1N4148
KSR1004
91K
1N4148
O
O
O
X
O
O
O
X
x
x
x
X
X
X
X
O
4HEAD
4HEAD
4HEAD
2HD LP
7
DM712
QM318
RM380
DM715
QM303
RM320
RM626
0504-000119
2001-000554
2001-000429
KSR1004
270
1K
X
X
X
X
X
X
X
X
X
O
O
O
8
DM714
0401-000005
1N4148
O
O
O
X
2HD LP
2HD LP
2HD LP
MESECAM
2
3
4
5
6
5-12
Samsung Electronics
Alignment and Adjustments (Electrical)
5-5-6 WITHOUT SECAM PART LIST
NO
L O C . NO
C O D E -NO
PARTS
SPEC
WITH
WITH-OUT
R E MAR K S
1
JM116
JM133
RM652
RM692
CM901
CM902
CM903
CM904
CM905
CM906
CM907
CM908
CM909
CM910
CM911
CM912
CM913
CM914
CM915
CM916
CM917
CM918
CM919
CM920
CM921
CM922
CM924
CM925
CM926
DM713
DM902
ICM901
3812-000219
3812-000219
2001-000429
2001-00429
2202-000127
2301-000224
2201-000374
2201-000193
2201-000645
2301-000383
2201-000681
2401-000480
2202-000796
2301-001333
2201-000796
2201-000127
2201-000632
2201-000234
2301-000383
2401-002691
2202-000632
2301-000383
2301-000383
2401-000660
2201-000262
2401-000603
2202-000632
2202-000632
2202-000127
0401-000005
0401-000005
1204-001437
WIRE
WIRE
R
R
JUMPER
X
O
O
X
ADD
SECAMI
O
O
O
X
SECAM
X
X
SECAM
X
SECAM
SECAM
O
X
X
681,50V
103
820,50V
10uF,50V
102
O
O
O
O
O
X
X
X
X
X
0.47uF,50V
510
103
104
151,50V
103,50V(P)
47uF,25V
O
O
O
O
O
O
O
O
X
X
X
X
X
X
X
X
SECAM
O
X
SECAM
O
O
O
O
X
X
X
X
X
X
X
SECAM
1N4148
1N4148
LA7359
O
O
O
X
SECAM
X
X
SECAM
JM126
JM170
JM185
JM196
LM901
LM902
3812-000219
3812-000219
3812-000219
3812-000219
2701-000002
2701-000163
C-AXIAL
C-AXIAL
C-AXIAL
DIODE
DIODE
IC
WIRE
WIRE
WIRE
WIRE
COIL
COIL
103,50V(P)
103,50V(P)
2.2uF,50V
181,50V
1uF,50V
104
104
103
JUMPER
O
X
SECAM
O
O
O
O
O
X
X
X
X
X
SECAM
LM903
LM904
LM905
QM901
2701-000158
2701-000191
2701-000208
0501-000398
COIL
COIL
COIL
COIL
JUMPER
JUMPER
JUMPER
100uH, (AL04)
27uH, (AL03)
22uH, (AL02)
47uH, (AL02)
6.8uH, (AL02)
KSC945-Y
O
X
SECAM
O
O
O
X
X
X
SECAM
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Samsung Electronics
C-AXIAL
C-RADIAL
C-RADIAL
C-RADIAL
C-RADIAL
C-RADIAL
C-RADIAL
C-ELEC
C-AXIAL
C-ELEC
C-AXIAL
C-AXIAL
C-AXIAL
C-RADIAL
C-RADIAL
C-ELEC
C-AXIAL
C-RADIAL
C-RADIAL
C-ELEC
C-RADIAL
C-ELEC
JUMPER
1K
1K
103
223,50V(P)
221,50V,NPO
100,50V
104
O
O
O
O
O
SECAMI
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAMI
SECAM
SECAM
SECAM
SECAM
SECAM
5-13
Alignment and Adjustments (Electrical)
NO
L O C . NO
C O D E -NO
PARTS
SPEC
WITH
WITH-OUT
R E MAR K S
43
QM902
QM904
QM905
QM906
RM376
RM901
RM902
RM903
RM904
RM905
RM906
RM907
RM908
RM909
RM910
RM912
RM913
RM914
RM915
RM916
RM917
RM918
RM919
RM920
RM921
RM922
0504-000142
0501-000398
0501-000398
0501-000303
2001-000258
2001-000522
2001-000472
2001-000539
2001-000947
2001-000890
2001-000837
2001-000723
2001-000633
2001-000890
2001-000429
2001-000674
2001-000281
2001-000786
2001-000539
2001-001015
2001-000977
2001-000356
2001-000734
2001-000539
2001-000429
2001-000319
WIRE
C-AXIAL
C-RADIAL
C-RADIAL
C-RADIAL
C-RADIAL
C-RADIAL
KSR2001
KSC945
O
O
X
X
SECAM
O
O
X
SECAM
SECAM
O
X
X
O
O
O
O
O
X
X
X
X
X
SECAM
O
O
O
O
O
O
O
O
X
X
X
X
X
X
X
X
O
X
SECAM
O
O
O
O
X
X
X
X
X
X
X
SECAM
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
5-14
C-RADIAL
C-ELEC
C-AXIAL
C-ELEC
C-AXIAL
C-AXIAL
C-AXIAL
C-RADIAL
C-RADIAL
C-ELEC
C-AXIAL
C-RADIAL
C-RADIAL
C-ELEC
C-RADIAL
C-ELEC
C-AXIAL
C-AXIAL
C-AXIAL
KSC945
KSA733
1.8K
22K
2.7K
24K
7.5K
6.8K
51K
4.3K
30K
6.8K
1K
360
100
47K
24K
9.1K
8.2K
150K
4.7K
24K
1K
120K
O
O
O
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
SECAM
Samsung Electronics
Alignment and Adjustments (Electrical)
5-5-7 USELESS TABLE
NO
L O C . NO
1
CM330
CM369
CM385
CM388
CM607
CM608
CM646
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
C O D E -NO
PARTS
SPEC
WITH
WITH-OUT
R E MAR K S
DM716
DM717
ICM604
LM311
RM326
RM337
RM374
RM375
RM379
RM608
RM617
RM692
RM695
XTM302
XTM602
Samsung Electronics
5-15
Alignment and Adjustments (Electrical)
MEMO
5-16
Samsung Electronics
Disassembly and Reassembly
´
Œ
Ø
∏
”
ˇ
’” Ô ˝ 
¨
ˆ
Ò
Fig. 4-2 Top Parts Location-2
Œ
´
ˇ
¨
ˆ
Ø
∏
4-2
FE HEAD
CYLINDER ASS’Y
ACE HEAD ASS’Y
LEVER UNIT PINCH ASS’Y
LEVER #9 GUIDE ASS’Y
LEVER TENSION ASS’Y
BAND BRAKE ASS’Y
”
’
˝
Ô

Ò
DISK S REEL
LEVER S BRAKE ASS’Y
GEAR IDLE
LEVER IDLE
LEVER T BRAKE ASS’Y
DISK T REEL
Samsung Electronics
Disassembly and Reassembly
4-1-2 Bottom View
Œ ´
¨
ˇ
”
’
ˆ Ø
∏
˝
Fig. 4-3 Bottom Parts Location
Œ
´
ˇ
¨
ˆ
Ø
∏
”
’
˝
GEAR JOINT 1
GEAR JOINT 2
BRACKET GEAR
MOTOR CAPSTAN ASS’Y
LEVER T LOAD ASS’Y
GEAR LOADING DRIVE
LEVER S LOAD ASS’Y
HOLDER CLUTCH ASS’Y
BELT PULLEY
SLIDER CAM
Samsung Electronics
4-3
Disassembly and Reassembly
4-2 Main Deck
4-2-1 Lever FL Door Removal
4-2-2 Holder FL Cassette Ass’y Removal
1) Push the Holder FL Cassette Ass'y Πabout 20mm
in the direction of arrow “A”.
2) Rotate the Lever FL Door ´ in the direction of
arrow “B”.
3) Release the Hook ˇ and Remove the Lever FL
Door ´ in the direction of arrow “C”.
1) Pull the Holder FL Cassette Ass'y Πto the eject
position.
2) Pull the Holder FL Cassette Ass'y Πas grasping
the Holder FL Cassette Ass'y Πand Lever FL
Cassette-R ´ in the same time to release hooking
from Main Base until the Boss [A] of Holder FL
Cassette Ass'y Πis taken out from the Rail [B].
3) Lift the Holder FL Cassette Ass'y Œ, in this time,
you have to grasp the Lever FL Cassette-R ´
Continuously until the Holder FL Cassette Ass'y
Πis taken out completely.
ΠHOLDER FL CASSETTE ASS'Y
"A"
Note : Be sure to insert Lever FL Cassette-R ´ in the
direction of “A” to prevent separation and breakage
of the Lever FL Cassette-R ´ at disassembling and
reassembling.
"B"
´ LEVER FL DOOR
ˇ HOOK
"C"
Fig. 4-4 Lever FL Door Removal
RAIL [B]
ΠHOLDER FL
CASSETTEE ASS`Y
"A" ´ LEVER FL CASSETTEE -R
BOSS [A]
Fig. 4-5 Holder FL Cassette Ass’y Removal
4-4
Samsung Electronics
Disassembly and Reassembly
4-2-3 Slider FL Drive, Gear FL Cam Removal
4-2-4 Lever FL Arm Ass’y Removal
1) Pull the Slider FL Drive Πto the front direction.
2) Remove the Slider FL Drive Πin the direction of
arrow. (Refer to Fig. 1-6)
3) Remove the Gear FL cam ´.
1) Push the hole “A” in the direction of arrow “B”
use the pin.(about Dia. 2.5)
2) Pull out the Lever FL Arm Ass'y Πfrom the Boss
of Main Base.
3) Remove the Lever FL Arm Ass'y Πin the direction
of arrow “C”.
Note : When reinstalling be sure to reassemble Slider
FL drive Πafter you insert the Boss of Lever FL
ARM-R in Groove of Slider Fl drive Œ.
HOLE "A"
Assembly : Align the Gear FL Cam Πwith the Gear
worm wheel Post as shown drawing.
(Refer to Timing point)
PIN
"B"
"C"
ΠLEVER FL ARM ASS`Y
Fig. 4-8 Lever FL Arm Ass’y Removal
´ GEAR FL CAM
ΠSLIDER FL DRIVE
Fig. 4-6 Slider FL Drive Removal
ΠGEAR FL CAM
GEAR WORM WHEEL
POST
TIMING POINT
Fig. 1-7 Gear FL Cam, Gear Worm
Samsung Electronics
4-5
Disassembly and Reassembly
4-2-5 Gear Worm Wheel Removal
4-2-6 Motor Loading Ass’y Removal
1) Remove the Gear Worm wheel Œ.
1) Remove the screw Œ.
2) Remove the Motor Loading Ass’y ´.
´ MOTOR LOADING ASS`Y
ΠSCREW
ΠGEAR WORM WHEEL
Fig. 4-10 Motor Loading Ass’y Removal
Fig. 4-9 Gear Worm Wheel Removal
4-6
Samsung Electronics
Disassembly and Reassembly
4-2-7 Bracket Gear, Gear Joint 2, 1 Removal
1) Remove the SCREW Œ.
2) Remove the Bracket Gear ´.
3) Remove the Gear Joint 2 ˇ.
4) Remove the Gear Joint 1 ¨.
Assembly :
1) Be sure to align dot mark of Gear Joint 1 Πwith
dot mark of Gear Joint 2 ´ as shown Fig 4-12.
(Refer to Timing point1)
2) Confirm the Timing Point 2 of the Gear Joint 2 ´
and Slider Cam ˇ.
4-2-8 Gear Loading Drive, Slider Cam,
Lever Load S, T Ass’y Removal
1) Remove the Belt Pulley. (Refer to Fig. 4-30)
2) Remove the Gear Loading Drive Πafter releasing
Hook [A] in the direction arrow as shown in detail
drawing.
3) Remove the Slider Cam ´.
4) Remove the Lever Load ˇ, Link Load ˆ & Lever
Load ¨, Link Load Ø.
HOOK(A)
¨ GEAR JOINT 1
´ SLIDE CAM
ˇ GEAR JOINT 2
ΠSCREW
´ BRAKET GEAR
ΠGEAR LOADING DRIVE
¨ LEVER LOAD T
Ø LINK LOAD T
ˇ LEVER LOAD S
ˆ LINK LOAD S
Fig. 4-11 Bracket Gear, Gear Joint 1,2 Removal
Fig. 4-13 Gear Loading Drive, Slider Cam,
Lever T, S Load Ass’y Removal
ΠGEAR JOINT1
´ GEAR JOINT2
ˇ SLIDER CAM
TIMING POINT 1
TIMING POINT 2
Fig. 4-12 Gear Joint 1,2 Assembly
Samsung Electronics
4-7
Disassembly and Reassembly
4-2-9 Gear Loading Drive, Slider Cam,
Lever Load S, T Ass’y Assembly
4-2-10 Lever Pinch Drive,
Lever Tension Drive Removal
1) When reinstalling, be sure to align dot of Lever
Load T Ass'y Œ with dot of Lever Load S Ass'y ´
as shown in drawing, (Refer to Timing Point 1).
2) Insert the Pin A,B,C,D into the Slider Cam ˇ hole,
3) Be sure to align dot of Lever Load T Πand dot of
Gear Loading Drive ¨, (Refer to Timing Point 2).
4) Aline dot of Gear Loading drive ¨ with mark of
Slider Cam ˇ as shown in drawing(Refer to
Timing Point 3).
1) Remove the Lever Pinch Drive Œ, Lever Tension
Drive ´.
ΠLEVER PINCH DRIVE
´ LEVER TENSION DRIVE
TIMING POINT 1
ΠLEVER LOAD T
´ LEVER LOAD S
LEVER LOAD T
LEVER LOAD S
Fig. 4-15 Lever Pinch Drive,
Lever Tension Drive Removal
TIMING POINT 2
TIMING POINT 3
PIN A
PIN C
PIN D PIN B
ˇ SLIDER CAM
Fig. 4-14 Gear Loading Drive, Slider Cam,
Lever Load S, T Ass’y Assembly
4-8
Samsung Electronics
Disassembly and Reassembly
4-2-11 Lever Tension Ass’y,
Band Brake Ass’y Removal
1) Remove the Lever Brake S Ass'y (Refer to Fig 4-17).
2) Remove the Spring Tension Lever Œ.
3) Rotate stopper of Main Base in the direction of
arrow “A”.
4) Lift the Lever Tension Ass'y ´ & Band brake
Ass'y ˇ.
Note :
1) When replacing the Lever Tension Ass'y ´, be sure
to apply Grease on the post,
2) Take care not to touch stain on the felt side, and not
to be folder and broken Band brake Ass'y
3) After Lever Tension Ass'y seated, Rotate stopper of
Main Base to the Mark[B].
4-2-12 Lever Brake S, T Ass’y Removal
1) Release the Hook [A] and the Hook [B], [C] in the
direction of arrow as shown in Fig 4-17.
2) Lift the Lever S, T Brake Ass'y Œ, ´ with spring
brake ˇ.
Assembly :
1)Assembly the Lever S Brake Ass'y Πon the Main
Base.
2)Assembly the Lever T Brake Ass'y ´ with spring
brake ˇ.
Note : Take extreme care not to be folded and
transformed Spring Brake at removing or reinstalling.
ˇ BAND BRAKE ASS`Y
HOOK(A)
´ LEVER TENTION ASS`Y
ˇ SPRING BRAKE
ΠSPRING TENTION LEVER
STOPPER
"A"
MARK[B]
ΠLEVER S BRAKE ASS`Y
HOOK(C)
HOOK(B)
´ LEVER T BRAKE ASS`Y
Fig. 4-16 Lever Tension Ass’y,
Band Brake Ass’y Removal
Fig. 4-17 Lever Brake S, T Ass’y Removal
Samsung Electronics
4-9
Disassembly and Reassembly
4-2-13 Gear Idle Ass’y Removal
4-2-14 Disk S, T Reel Removal
1) Push the Lever Idle Πin the direction of arrow
“A”, “B”.
2) Lift the Lever Idle Œ.
1) Lift the Disk S, T Reel Œ, ´.
ΠDISK S REEL
Assembly :
1) Apply oil in two Bosses of Lever Idle Œ.
2) Assemble the Gear Idle ´ with the Lever Idle Œ.
Note : When replacing the Gear Idle ´, be sure to
add oil in the boss of Lever Idle Œ.
´ DISK T REEL
"A"
ΠLEVER IDLE
´ GEAR IDLE
"B"
´ GEAR IDLE
HOOK "C"
Fig. 4-19 Disk S, T Reel Removal
Fig. 4-18 Gear Idle Ass’y Removal
4-10
Samsung Electronics
Disassembly and Reassembly
4-2-15 Holder Clutch Ass’y Removal
1) Remove the Washer Slit Œ.
2) Lift the Holder Clutch Ass’y ´.
Note : When you reinstall Holder Clutch Ass'y
1) Check the condition of spring as shown in detail A.
2) Don't push Holder Clutch Ass'y down with excessive force Just insert Holder Clutch Ass'y into post
center with dead force and Rotate it smoothly.
Be sure to confirm that spring is in the slit of Gear
Center Ass'y as shown in detail B.
ΠWASHER SLIT
´ HOLDER CLUTCH ASS`Y
4-2-16 Lever Up Down Ass’y, Gear Center
Ass’y Removal
1) Remove the 2 hooks in the direction of arrow as
shown Fig. 4-21 and lift the Lever Up Down Ass’y Œ.
2) Lift the Gear Center Ass’y ´.
Assembly :
1) Insert the Lever Up Down Ass'y Πin the rectangular holes on Main Base as shown in Fig 4-22.
2) Lift the Lever Up Down Ass'y Œ about 35°.
(Refer to Fig 4-22)
3) Insert Ring of the Gear Center Ass'y ´ in the
Guide of the Lever Up Down Ass'y Œ.
4) Insert the Gear Center Ass'y ´ in the post on
Main Base.
5) Push down the Lever Up Down Ass'y Πfor
locking of the Hook.
Note :
1) Take care not to separate and sentence does not
mark sense.
2) Be sure to confirm that Ring of the Gear Center
Ass'y ´ is in the Guide of the Lever Up Down
Ass'y Πafter finishing assembly of Lever Up
Down Ass'y Œ and Gear Center Ass'y ´.
ΠLEVER UP DOWN ASS`Y
´ GEAR CENTER ASS`Y
DETAIL A
<BAD>
SPRING
<GOOD>
DETAIL B
Fig. 4-21 Lever Up Down Ass’y Removal
SPRING
GEAR CENTER ASS'Y
GUIDE
LEVER UP DOWN ASS'Y
<BAD>
<GOOD>
RING
GEAR
POST
HOOK
35
Fig. 4-20 Holder Clutch Ass’y Removal
MAIN BASE
Fig. 4-22 Lever Up Down Ass’y Removal
Samsung Electronics
4-11
Disassembly and Reassembly
4-2-17 Guide Cassette Door Removal
1) Lift the Hook [A].
2) Rotate the Guide Cassette Door Πin the direction
of arrow.
Note : After reinstalling the Guide Cassette Door Œ
sure the Hook [A].
ΠGUIDE CASSETTE DOOR
4-2-18 Lever Unit Pinch Ass’y, Plate Joint,
Spring Pinch Drive Removal
1) Lift the Unit Pinch Ass’y Œ.
2) Remove the Plate Joint ´ from Lever Pinch Drive.
3) Remove the Spring Pinch Drive ˇ.
Note :
1) Take extreme care not to touch the grease on the
Roller Pinch.
2) When reinstalling, be sure to apply grease on the
post pinch roller.
ΠLEVER UNIT PINCH ASS`Y
HOOK [A]
´ PLATE JOINT
ˇ SPRING PINCH DRIVE
Fig. 4-23 Guide Cassette Door Removal
Fig. 4-24 Lever Unit Pinch Ass’y, Plate Joint,
Spring Pinch Drive Removal
4-12
Samsung Electronics
Disassembly and Reassembly
4-2-19 Lever #9 Guide Ass’y Removal
4-2-20 FE Head Removal
1) Remove the Spring #9 Guide Œ.
2) Lift the Spring #9 Guide Ass’y ´ in the direction
of arrow “A”.
1) Remove the screw Œ.
2) Lift the FE Head ´.
Note :
1) Take extreme care not to get grease on the tape
Guide Post.
2) After reinstalling, check the bottom side of the Post
#9 Guide to the top side of Main Base.
ΠFE HEAD
"A"
ΠSPRING #9 GUIDE
´ LEVER #9 GUIDE ASS`Y
"B"
Fig. 4-26 FE Head Removal
Fig. 4-25 Lever #9 Guide Ass’y Removal
Samsung Electronics
4-13
Disassembly and Reassembly
4-2-21 ACE Head Removal
4-2-22 Slider S, T Ass’y Removal
1) Pull out the FPC from connector of ACE Head
Ass’y ´.
2) Remove the screw Œ.
3) Lift the ACE Head Ass’y ´.
1) Move the Slider S, T Ass’y Œ, ´ to slot, and then
lift it to remove. (Refer to arrow)
ΠSLIDER S ASS`Y
ΠSCREW
´ SLIDER T ASS`Y
´ HEAD ACE ASS`Y
Fig. 4-28 Slider S, T Ass’y Removal
Fig. 4-27 ACE Head Removal
4-14
Samsung Electronics
Disassembly and Reassembly
4-2-23 Plate Ground Deck, Cylinder Ass’y Removal
4-2-24 Belt Pulley Removal
1) Remove the 3 Screws Œ.
2) Lift the Plate Ground Deck ´.
3) Lift the Cylinder Ass’y ˇ.
1) Remove the Belt Pulley Œ.
Note : Take extreme care not to get grease on Belt
Pulley Πat assembling or reassembling.
Assembly :
1) Match the 3 holes in the bottom of Cylinder ass'y
ˇ to the 3 holes of Main Base as attending not to
drop or knock the Cylinder ass'y ˇ.
2) Tighten the 1 Screw Œ.
3) Match the Plate Ground Deck ´ to the Hole of
Base Main.
4) Tighten the other 2 Screws Œ.
ΠBELT PULLEY
Note :
1) Take care not to touch the Cylinder Ass'y ˇ and
the tape guide post at reinstalling.
2) When reinstalling, Don't push down too much on
Screw Driver.
Π3 SCREWS
Fig. 4-30 Belt Pulley Removal
´ PLATE GROUND DECK
1-2-25 Level Head Cleaner Ass’y Removal
(Optional)
1) Release the Hook Œ.
2) Lift the Lever Head Cleaner Ass’y ´.
´ LEVER HEAD CLEANER ASS'Y
ΠHOOK
SLEEVE-HEAD CLEANER
ˇ CYLINDER ASS'Y
Fig. 4-29 Plate Ground Deck, Cylinder Ass’y Removal
Samsung Electronics
Fig. 4-31 Level Head Cleaner Ass’y Removal
4-15
Disassembly and Reassembly
4-2-26 Damper Capstan, Motor Capstan Ass’y
Removal
1) Remove the Damper Capstan Πin the direction
of arrow.
2) Remove the 3 Screws ´.
3) Remove the Motor Capstan Ass’y ˇ.
4-2-27 How to Eject the Cassette Tape
(If the unit does not operate on condition that is
inserted into housing ass’y)
1) Turn the Gear worm Πclockwise with screw
driver.(Refer to arrow)
(Other method : Remove the Screw of Motor Load
Ass'y, Separate the Motor Load Ass'y)
Assembly :
1) Match the 3 holes of Motor Capstan Ass’y ˇ to the
3 holes of Main Base. Be careful not to drop or
knock the Motor Capstan Ass'y ˇ.
2) Tighten the 3 Screws ´ in the direction of arrow
as shown detail drawing.
3) Assemble the Damper Capstan Œ.
ΠGEAR WORM
Note : After tightening screws, check if there is gap
between the head of screws and the top side of Main
Base. There should have no gap between the head of
screws and the top side of Main Base.
After reinstalling, adjusting the tape transport
system again.
´ 3 SCREWS
A
B
Fig. 4-33
C
ΠDAMPER CAPSTAN
2) When Slider S,T are approched in the position of
unloading, rotate holder Clutch counterclockwise
after inserting screw driver in the hole of frame's
bottom in order to wind the unwinded tape.
(Refer to Fig.4-34)
(If you rotate Gear Worm Πcontinuously when
tape is in state of unwinding, you may cause a
tape contamination by grease and tape damage.
Be sure to wind the unwinded tape in the state of
set horizently.)
3) Rotate Gear Worm Πclockwise using screw driver
again up to the state of eject mode and then pick
out the tape.(Refer to Fig.4-33)
ˇ MOTOR CAPSTAN ASS'Y
Fig. 4-32 Damper Capstan,Motor Capstan Ass’y Removal
FRAME
Fig. 4-33
4-16
Samsung Electronics
Disassembly and Reassembly
4-3 The table of clearing, Lubrication and replacement time about principal parts
1) The replacement time of parts is not life of parts.
2) The table 1-1 is that the VCR Set is in normal condition (normal temperature, normal humidity).
The checking period may be changed owing to the condition of use, runtime and environmental conditions.
3) Life of the Cylinder Ass’y is depend on the condition of use.
4) See exploded view for location of each parts.
<Table 1-1>
*
T
A
PE
P
A
T
H
S
Y
S
T
E
M
D
R
I
V
I
N
G
S
Y
S
T
E
M
B
R
A
K
E
S
Y
S
T
E
M
Parts Name
POST TENSION
SLANT POST S, T
#8 GUIDE SHAFT
CAPSTAN SHAFT
#9 GUIDE POST
#3 GUIDE POST
GUIDE ROLLER S, T
CYLINDER ASS’Y
FE HEAD
ACE HEAD
PINCH ROLLER
POST REEL S, T
SLEEVE TENSION
POST CENTER
LEVER IDLE BOSS (2Point)
CAPSTAN MOTOR PULLEY
BELT PULLEY
HOLDER CLUTCH ASS’Y
GEAR CENTER ASS’Y
GEAR IDLE (2Point)
LOADING MOTOR
BAND BRAKE ASS’Y
BRAKE T ASS’Y
Checking Period
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
O
∆
O
O
∆
∆
∆
∆
∆
∆
∆
O
∆
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
∆
∆
∆
∆
∆
∆
O
O
O
O
O
- To clean the parts, use patch and
alcohol (solvent).
- After cleaning, use the video tape
after alcohol is gone away completely.
- We recommend to use oil [EP-50]
or solvent.
- One or two drops of oil should be
applied after
cleaning with alcohol.
- Periodic time of applying oil (Apply
oil after cleaning)
- The excessive applying oil may be
the cause of
malfunction.
∆
∆
∆
∆
O
O
O
O
O
O
O
O
O
O
O
O
∆ : Cleaning
Samsung Electronics
Remark
∆
O
O
O
O
O
O
O
∆
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O : Check and replacement in necessary
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
: Add Oil
4-17
Disassembly and Reassembly
4-4 Tape Transport System and Adjustment Locations
The tape transport system has been adjusted precisely in the factory. Alignment is not necessary except for the
following :
1) Noise observed on the screen.
2) Tape damage.
3) Parts replacement in the tape transport system.
Lower flange height of tape guide is used as the reference for the transport adjustment.
To maintain the height of the tape guide and prevent damage, do not apply excessive force onto the main base.
CYLINDER ASS'Y
GUIDE ROLLER "S"
GUIDE ROLLER "T"
FULL ERASE HEAD
HEIGHT SCREW
#3 GUIDE POST
TENSION POST
PINCH ROLLER
TILT SCREW
X - POSITION
ADJUST SILT
#9 GUIDE POST
AZIMUTH SCREW
CAPSTAN
#8 GUIDE POST
TAKE UP REEL DISK
SUPPLY REEL DISK
Fig. 4-4-1 Location of Tape Transport Adjustment
PINCH ROLLER
FE HEAD
CYLINDER ASS'Y
GUIDE ROLLER "S"
GUIDE ROLLER "T"
POST TENSION
#8 GUIDE POST #9 GUIDE POST
#3 GUIDE POST
MAIN BASE
ACE HEAD
CAPSTAN SHAFT
Fig. 4-4-2 Tape Travel Diagram
4-18
Samsung Electronics
Disassembly and Reassembly
4-5 Tape Transport System Adjustment
When parts are replaced, perform the required
adjustments by referring to procedures for the tape
transport system. If there are any changes to the tape
path, first run a T-120 tape and make sure excessive
tape wrinkle does not occur at the tape guides.
1) If tape wrinkle is observed at the guide roller S, T,
turn the guide roller S, T until wrinkle disappears.
2) If the tape wrinkle is still observed at the tape
guide, perform the tilt adjustment of the ACE head.
(See “2. Alignment and Adjustment” of the
Service Manual for Test Point Locations.)
4-5-1(b) ACE HEAD TILT ADJUSTMENT
1) Playback a blank tape and observe the position of
the tape at the lower flange of tape guide.
2) Confirm that there is no curl or wrinkle at the
lower flange of tape guide as shown in Fig. 4-5-3(B).
3) If a curl or wrinkle of the tape occurs, slightly turn
the screw (A) tilt adjust on the ACE head ass’y.
4) Reconfirm the ACE head height.
4-5-1 ACE Head Assembly Adjustment
WRINKLE
4-5-1(a) ACE HEAD HEIGHT ADJUSTMENT
1) Run the alignment tape (Color bar) in the playback
mode.
2) Observe surface of the audio head using a dental
mirror.
3) Turn screw (C) clockwise or counterclockwise until
the gap of lower tape edge and the lower edge of
the control head is about 0.25mm.
(Refer to Fig. 4-5-1 and 4-5-2)
SCREW (A)
TLIT ADJUST
SCREW (C)
HEIGHT ADJUST
X-POSITION
ADJUSTING SLIT
SCREW (D)
X-POSITION LOCKING
SCREW (B)
AZIMUTH ADJUST
Fig. 4-5-1 Location of ACE Head Adjustment Screw
(BAD)
(GOOD)
Fig. 4-5-3 Tape Guide Check
4-5-1(c) AUDIO AZIMUTH ADJUSTMENT
1) Load alignment tape (Mono scope) and playback
the NTSC : 7KHz (PAL : 6KHz) signal.
2) Connect channel-1 scope probe to audio output
test point.
3) Adjust screw (B) to achieve maximum audio level.
(See Fig. 4-5-1)
4-5-1(d) ACE HEAD POSITION (X-POINT)
ADJUSTMENT
1) See “2. Alignment and Adjustment” for ACE Head
position (X-Point) adjustment.
AUDIO HEAD
VIDEO HEAD
0 ~ 0 .25 mm
CONTROL HEAD
Fig. 4-5-2 ACE Head Height Adjustment
Samsung Electronics
4-19
Disassembly and Reassembly
4-5-2 Linearity adjustment
(Guide roller S, T adjustment)
c
a
b
1) Playback the Mono Scope alignment tape (SP mode).
2) Observe the video envelope signal on an oscilloscope (triggered by the video switching pulse).
3) Make sure the video envelope waveform (at its
minimum) meets the specification shown in
Fig. 4-5-4.
If it does not, adjust as follows :
abcd
c,b,d/a
d
63%
Fig. 4-5-4 Envelope Waveform Adjustment
Note :
a=Maximum output of the video RF envelope.
b=Minimum output of the video RF envelope at the
entrance side.
c=Minimum output of the video RF envelope at the
center point.
d=Maximum output of the video RF envelope at the
exit side.
4) If the section A in Fig. 4-5-5 does not meet the
speci-fication, adjust the guide roller S up or
down.
5) If the section B in Fig. 4-5-5 does not meet the
speci-fication, adjust the guide roller T up or down.
H'D SWITCHING
PULSE
A
ENVELOPE
B
A
B
Fig. 4-5-5 Adjustment Points
6) Play back the Mono Scope alignment tape (SP mode).
7) Connect an oscilloscope CH-1 to the Envelope and CH-2 to the H’D SW Pulse for triggering.
8) Turn the guide roller heads with a flat head (
) driver to obtain a flat video RF envelope as shown in Fig. 2-8.
IDEAL ENVELOPE
S HEIGHT TOO HIGH
S HEIGHT TOO LOW
T HEIGHT TOO HIGH
GUIDE ROLLER S
T HEIGHT TOO LOW
GUIDE ROLLER T
Fig. 4-5-6 Guide Roller S, T Height Adjustment
4-20
Samsung Electronics
Disassembly and Reassembly
4-5-3 Check Transitional Operation from
RPS to Play
Check transition from RPS mode to play mode :
Using a pre-recorded SP tape, make sure the entry
side of envelope comes to an appropriate steady state
within 3 seconds (as shown in Fig. 4-5-7).
If the envelope waveform does not reach specified
peak-to peak amplitude within 3 seconds, adjust as
follows :
1) Make sure there is no gap between the supply
roller lower flange and the tape.
If there is a gap, adjust the supply guide roller
again.
2) Change operation mode from the RPS to the play
mode (again) and make sure the entry side of
envelope rises within 3 second.
4-5-4 Envelope Check
1) Make recordings on T-120 (E-120) and T-160
(E-180) tape.
Make sure the playback output envelope meets the
specification as shown in Fig. 4-5-8.
2) Play back a self recorded tape (recording made on
the unit using with T-120 (E-120).
The video envelope should meet the specification
as shown in Fig. 4-5-8.
In SP mode, (A) should equal (B).
If the head gap is wide, upper cylinder should be
checked.
A
B
ENTRANCE SIDE ENVELOPE
Fig. 4-5-8 Envelope Output and Output Level
4-5-5 Tape Wrinkle Check
1) Run the T-160 (E-180) tape in the playback, FPS,
RPS and Pause modes and observe tape wrinkle at
each guide.
2) If excessive tape wrinkle is observed, perform the
following adjustments in Playback mode :
Fig. 4-5-7 Video Envelope Rising when Operation mode Changes
from RPS to Play Mode
Tape wrinkle at the guide roller S, T section :
Linearity adjustment.
Tape wrinkle at tape guide flange :
ACE head assembly coarse adjustment.
4-6 Reel Torque
1) The rotation of the capstan motor causes the
Holder Clutch Ass’y to rotate through the Belt
Pulley.
2) The spring wrap PLAY/REV of holder clutch ass’y
drives the disk reel S, T through gear idle by rotation of gear center ass’y.
3) Brake is operated by slider cam at FF/REW mode.
4) Transportation of accurate driving force is done by
gears. (Gear Center Ass’y)
<Table 2-1>
MODE
TORQUE g/cm
GAUGE
PB
42 ± 11
Cassette Torquemeter
RPS
145 ± 30
Cassette Torquemeter
Note : If the spec. does not meet the followings specifications, replace the holder clutch ass’y and then
recheck.
Samsung Electronics
4-21
Disassembly and Reassembly
3-1-2 Main Assembly Removal
1. Release two connectors between sub PCB and Main Assembly.
2. Pull the Main Assembly backwards to remove.
3-2
Samsung Electronics
Disassembly and Reassembly
3-1-3 Monitor Frame Removal
1. Remove 3 screws from the Main Assembly. Remove the dust cover.
2. Remove 4 screws from the Deck Assembly.
Samsung Electronics
3-3
Disassembly and Reassembly
3-1-4 Deck Assembly Removal
3-1-5 Main Assembly Removal
1. Remove 2 screws holding the bottom cover.
1. Remove 2 screws holding the upper chassis
housing.
2. Remove one screw from Main PCB
Assembly. Take off the deck Assembly.
2. Remove 3 screws holding the deck assembly.
3. Lift the deck assembly upward to remove.
3-4
Samsung Electronics
Disassembly and Reassembly
3-1-6 Top Cabinet Removal
1. Remove two (2) screws located at the rear of
the top cabinet.
2. Carefully lift the back of the top cabinet and
shield it to the rear to remove.
3-1-7 Top Cabinet Removal
Samsung Electronics
3-1-8 Top Cabinet Removal
3-5
MEMO
2-2
Samsung Electronics
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or
electrical design of this unit. Example: Do not
add auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also,
any design changes or additions will void the
manufacturer’s warranty.
11. Hot Chassis Warning:
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only
if the AC power plug is inserted so that the
chassis is connected to the ground side of the
AC source.
To confirm that the AC power plug is inserted
correctly, do the following: Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the
reading is greater than 1.0V, remove the AC
power plug, reverse its polarity and reinsert.
Re-measure the voltage between the chassis
and ground.
12. Some TV chassis are designed to operate with
85 volts AC between chassis and ground,
regardless of the AC plug polarity. These units
can be safely serviced only if an isolation
transformer inserted between the receiver and
the power source.
13. Some TV chassis have a secondary ground
system in addition to the main chassis ground.
This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulating material that must not be defeated
or altered.
15. Observe the original lead dress, especially
near the following areas: Antenna wiring,
sharp edges, and especially the AC and high
voltage power supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do
not change the spacing between components
and the printed circuit board. Check the AC
power cord for damage. Make sure that leads
and components do not touch thermally hot
parts.
16. Picture Tube Implosion Warning:
The picture tube in this receiver employs
“integral implosion” protection. To ensure
continued implosion protection, make sure
that the replacement picture tube is the same
as the original.
17. Do not remove, install or handle the picture
tube without first putting on shatterproof
goggles equipped with side shields. Never
handle the picture tube by its neck. Some
“in-line” picture tubes are equipped with a
permanently attached deflection yoke; do not
try to remove such “permanently attached”
yokes from the picture tube.
18. Product Safety Notice:
Some electrical and mechanical parts have
special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they
give might be lost if the replacement component differs from the original—even if the
replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
(
) or ( ! ).
Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications.
A replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
14. Components, parts and wiring that appear to
have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or overheating, and correct any potential hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between
the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the
cabinet. Follow them.
2. Always unplug the unit’s AC power cord from
the AC power source before attempting to: (a)
Remove or reinstall any component or
assembly, (b) Disconnect an electrical plug or
connector, (c) Connect a test component in
parallel with an electrolytic capacitor.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or
tape is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around
the serviced part has not been damaged.
Samsung Electronics
5. Check the insulation between the blades of the
AC plug and accessible conductive parts
(examples: metal panels, input terminals and
earphone jacks).
6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the
power switch ON. Connect an insulation
resistance meter (430V) to the blades of the AC
plug.
The insulation resistance between each blade
of the AC plug and accessible conductive parts
(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
its assemblies) unless all solid-state heat sinks
are correctly installed.
8. Always connect a test instrument’s ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument’s ground lead last.
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor (“solid state”) devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect
transistors. The following techniques will
reduce the occurrence of component damage
caused by static electricity.
2. Immediately before handling any semicon
ductor components or assemblies, drain the
electrostatic charge from your body by
touching a known earth ground. Alternatively,
wear a discharging wrist-strap device. (Be
sure to remove it prior to applying power—
this is an electric shock precaution.)
3. After removing an ESD-equipped assembly,
place it on a conductive surface such as
aluminum foil to prevent accumulation of
electrostatic charge.
4. Do not use freon-propelled chemicals. These
can generate electrical charges that damage
ESDs.
1-4
5. Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
“anti-static”; these can accumulate sufficient
electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its
protective package until you are ready to
install it. Most replacement ESDs are
packaged with leads that are electrically
shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
9. Minimize body motions when handling
unpackaged replacement ESDs. Motions such
as brushing clothes together, or lifting a foot
from a carpeted floor can generate enough
static electricity to damage an ESD.
Samsung Electronics
ELECTRONICS
© Samsung Electronics Co., Ltd. Jun. 2001
Printed in Korea
AA68-01729A