Rittal SK 3377. series Operating instructions

SchaltschrankKühlgerät
Cooling unit
Climatiseur
Koelaggregaat
Kylaggregat
Condizionatori per
armadi di comando
Refrigerador
para armarios
SK 3302.xxx
SK 3302.3xx
SK 3303.xxx
SK 3304.xxx
SK 3305.xxx
SK 3328.xxx
SK 3329.xxx
SK 3332.xxx
SK 3361.xxx
SK 3366.xxx
SK 3377.xxx
Montage-, Installations- und Bedienungsanleitung
Assembly and operating instructions
Manuel d’installation et de maintenance
Montage- en bedieningshandleiding
Montage- och hanteringsanvisning
Istruzioni di montaggio e funzionamento
Instrucciones de montaje
R
Contents
1 Notes on documentation. . . . . . . . . . 4
1.1
1.2
1.3
1.4
Associated documents . . . . . . . . . . . . . . . . .
CE labelling . . . . . . . . . . . . . . . . . . . . . . . . . .
Retention of documents . . . . . . . . . . . . . . . .
Symbols used . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
4
2 Safety instructions. . . . . . . . . . . . . . . 4
3 Device description . . . . . . . . . . . . . . . 5
3.1
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.1.6
3.1.7
3.1.8
3.2
3.3
Functional description . . . . . . . . . . . . . . . . .
How it works . . . . . . . . . . . . . . . . . . . . . . . . . .
Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus mode (Comfort controller only) . . . . . . . .
Safety equipment . . . . . . . . . . . . . . . . . . . . . .
Condensation . . . . . . . . . . . . . . . . . . . . . . . . .
Filter mats . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door limit switch . . . . . . . . . . . . . . . . . . . . . . .
Additional interface X3 . . . . . . . . . . . . . . . . . .
Proper usage . . . . . . . . . . . . . . . . . . . . . . . . .
Scope of supply . . . . . . . . . . . . . . . . . . . . . .
5
5
5
5
6
6
6
6
7
7
7
4 Assembly and connection . . . . . . . . 7
4.1
4.2
4.2.1
4.2.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.4
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.5.6
4.6
4.6.1
4.6.2
4.6.3
4.7
4.7.1
4.7.2
4.7.3
Choosing the installation site . . . . . . . . . . . 7
Assembly instructions . . . . . . . . . . . . . . . . . 7
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Layout of the electronic components
in the enclosure. . . . . . . . . . . . . . . . . . . . . . . . 8
Fitting the cooling unit . . . . . . . . . . . . . . . . . 8
Cutting out the enclosure . . . . . . . . . . . . . . . . 9
External mounting of the cooling unit . . . . . . . 9
Partial internal mounting
of the cooling unit . . . . . . . . . . . . . . . . . . . . . . 9
Full internal mounting of the cooling unit . . . 11
Connecting the condensate discharge . . . 11
Notes on electrical installation . . . . . . . . . 12
Connection data . . . . . . . . . . . . . . . . . . . . . . 12
Overvoltage protection
and supply line load . . . . . . . . . . . . . . . . . . . 12
Three-phase devices . . . . . . . . . . . . . . . . . . 12
Door limit switch . . . . . . . . . . . . . . . . . . . . . . 12
Notes on the flicker standard . . . . . . . . . . . . 12
Potential equalisation . . . . . . . . . . . . . . . . . . 12
Carrying out the electrical installation . . . 13
Bus connection
(only in conjunction with several units with
a Comfort controller) . . . . . . . . . . . . . . . . . . . 13
Connection X3 for serial interface. . . . . . . . . 13
Installing the power supply . . . . . . . . . . . . . . 14
Finalising assembly . . . . . . . . . . . . . . . . . . 22
Installing the filter media . . . . . . . . . . . . . . . 22
Fitting the cooling unit. . . . . . . . . . . . . . . . . . 22
Setting the filter mat monitor
(only with Comfort controller) . . . . . . . . . . . . 22
RITTAL cooling unit assembly and operating instructions
5 Commissioning . . . . . . . . . . . . . . . . 22
6 Operation . . . . . . . . . . . . . . . . . . . . . 23
6.1
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.2
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
6.2.6
Control using the Basic controller . . . . . . 23
Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Operating and error display. . . . . . . . . . . . . .24
Test mode for the Basic controller . . . . . . . . .25
Setting the temperature . . . . . . . . . . . . . . . . .25
Resetting the Basic controller . . . . . . . . . . . .25
Control using the Comfort controller . . . . 26
Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Launching test mode . . . . . . . . . . . . . . . . . . .26
General programming information . . . . . . . . .26
Editable parameters. . . . . . . . . . . . . . . . . . . .27
Programming overview . . . . . . . . . . . . . . . . .28
Defining system messages
for evaluation . . . . . . . . . . . . . . . . . . . . . . . . .29
6.2.7 Setting the master-slave identifier . . . . . . . . .30
6.2.8 Evaluating system messages. . . . . . . . . . . . .30
6.2.9 Resetting the Comfort controller . . . . . . . . . .32
7 Inspection and maintenance. . . . . . 32
7.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.1.1 Compressed air cleaning
SK 3304.xxx, SK 3305.xxx . . . . . . . . . . . . . . .32
7.1.2 Compressed air cleaning
SK 3328.xxx, SK 3329.xxx, SK 3332.xxx . . . .36
8 Storage and disposal. . . . . . . . . . . . 41
9 Technical specifications . . . . . . . . . 41
10 List of spare parts . . . . . . . . . . . . . . 45
11 Appendix:
Cut-out and hole sizes . . . . . . . . . . . 49
11.1 Dimensions for external mounting . . . . . . 49
11.2 Dimensions for partial
internal mounting . . . . . . . . . . . . . . . . . . . . 50
11.3 Dimensions for full internal mounting . . . 51
3
EN
1 Notes on documentation
1
EN
Notes on documentation
These assembly instructions are aimed at tradespersons who are familiar with assembly and installation
of the cooling unit, and at trained specialists who are
familiar with operation of the cooling unit.
1.1 Associated documents
There are two sets of instructions for the unit types
described here:
– Assembly and installation instructions enclosed
with the unit in the form of a paper document
– Assembly, installation and operating instructions
enclosed with the unit in the form of a PDF file
(Adobe Acrobat) on CD-ROM
We cannot accept any liability for damage associated with failure to observe these instructions. Where
applicable, the instructions for any accessories used
also apply.
1.2 CE labelling
The declaration of conformity is supplied with the unit
as a separate document.
1.3 Retention of documents
These instructions and all associated documents
constitute an integral part of the product. They must
be given to the plant operator. The plant operator is
responsible for storage of the documents so they are
readily available when needed.
1.4 Symbols used
Please observe the following safety instructions and
other notes in this guide:
Symbol for an instructed action:
• The bullet point indicates that you should perform
an action.
Safety and other instructions:
2
Safety instructions
Please observe the following general safety instructions when assembling and operating the unit:
– Assembly, installation and servicing may only be
performed by properly trained specialists.
– Screw the enclosure to the floor to prevent it from
tipping over when the cooling unit is installed.
– Do not obstruct the air inlet and air outlet of the
cooling unit inside and outside the enclosure
(see also section 4.2.2).
– To ensure problem-free opening and closing of
the enclosure door, use a ride-up door roller (refer
to the accessories in the RITTAL Catalogue).
This raises the door slightly and balances out the
weight of the cooling unit, to prevent buckling of
the door and associated seal problems.
– The heat loss of the components installed in the
enclosure must not exceed the specific useful
cooling output of the cooling unit.
– When transporting the enclosure with the cooling
unit externally mounted, always use an additional
shipping brace to support the cooling unit.
– The cooling unit must always be transported in an
upright position.
– Use only original spare parts and accessories.
– Do not make any changes to the cooling unit other
than those described in these instructions or associated instructions.
– Risk of burn injuries! For cooling units with automatic condensate evaporation, the surface of the
thermal element will get very hot during operation,
and will remain so for some time afterwards.
– The mains connector of the cooling unit must only
be connected and disconnected with the system
de-energised. Connect the pre-fuse specified on
the rating plate.
Danger!
Immediate danger to life and limb!
Caution!
Potential threat to the product
and its environment.
Note:
Useful information
and special features.
4
RITTAL cooling unit assembly and operating instructions
3 Device description
3
Device description
Depending on the model chosen, your cooling unit
may vary in appearance from the illustrations contained in these instructions. However, the functions
are identical in principle.
into the hermetically sealed cooling circuit provides
effective protection against moisture, acid, dirt
particles, and foreign bodies within the cooling
circuit.
Condenser (3)
PSAH
8
9
1
pressureoperated
switch
Compressor
(2)
Condenser fan
Filter dryer (5)
2
10
3
External circuit
Internal circuit
Temperature
control
4
5
11
6
12
Evaporator coil (1)
Expansion valve (4)
Evaporator fan
13
Fig. 2:
7
14
15
16
Fig. 1:
Device description
Legend
1
Blind nut
2
Evaporator fan
3
Electrical wiring plan
4
X2 master-slave connection
5
X3 optional serial interface
6
X1 terminal strip
7
Air outlet hole
8
Front half of the enclosure
9
Rear half of the enclosure
10 Louvred grille for air outlet
11 Display
12 Infill panel
13 Louvred grille for air inlet
14 Rating plate
15 Condensate discharge
16 Dispatch bag
3.1 Functional description
Enclosure cooling units are designed to dissipate
heat from enclosures by cooling the air inside the
enclosure and so protect the temperature-sensitive
components. They are built into the side or rear
panel or into the door of the enclosure.
3.1.1 How it works
The cooling unit (compression refrigeration system)
is comprised of four main components (cf. Fig. 2):
the evaporator (1), the coolant compressor (2), the
condenser (3), and the control or expansion valve
(4), which are connected by suitable pipework. This
circuit is filled with a readily boiling substance, the
refrigerant. Coolant R134a (CH2FCF3) is chlorinefree. Its ozone destruction potential is 0, making it
very eco-friendly. A filter dryer (5) which is integrated
RITTAL cooling unit assembly and operating instructions
Cooling circuit
In the evaporator coil (1), the liquid coolant is converted to a gaseous state. The energy needed for
this purpose is taken from the enclosure air in the
form of heat, which has the effect of cooling the
enclosure air. In the compressor (2), the coolant is
heavily compressed, so that it achieves a higher
temperature inside the condenser (3) than the ambient air. This means that excess heat may be emitted
to the ambient air via the surface of the condenser,
as a result of which the temperature of the coolant
drops and it is converted back into liquid. It is reinjected into the evaporator coil via a thermostatic
expansion valve (4), which causes it to cool down
further, and is then once again able to absorb the
energy from the enclosure air in the evaporator coil.
The whole cycle begins again.
3.1.2 Control
RITTAL enclosure cooling units are fitted with a controller for setting the functions of the cooling unit.
Depending on the design, this is either a Basic controller (display of the operating status via LED) or a
Comfort controller (display plus extended functions,
see chapter “6 Operation”, page 23).
3.1.3 Bus mode (Comfort controller only)
The serial unit interface X2 allows you to create a bus
connection with up to ten cooling units using the
master-slave cable (shielded, four-wire cable, Model
No. SK 3124.100). This allows you to implement the
following functions:
– Parallel unit control (the cooling units in the network
can be switched on and off simultaneously)
– Parallel door status message (“door open”)
– Parallel collective fault message
Data is exchanged via the master-slave connection.
During commissioning, assign an address to each
unit that also includes the identifier “master” or
“slave”.
5
EN
3 Device description
EN
3.1.4 Safety equipment
– In the cooling cycle, the cooling unit has a tested
pressure-operated switch to EN 12 263 which is
set to maximum PS (admissible pressure); this
operates via an automatic reset device whenever
the pressure drops again.
– Temperature monitoring prevents the evaporator
coil from icing over. If there is a risk of icing, the
compressor switches itself off and automatically
switches itself back on again at higher temperatures.
– The refrigerant compressor and the fans are
equipped with thermal winding shields to protect
against excess current and excess temperatures.
– In order to allow a reduction of pressure inside the
compressor and hence a safe restart, once it has
been switched off (e.g. upon reaching the set temperature via the door limit switch function or via deenergising), the device will switch back on with a
delay of 180 seconds.
– The device has floating contacts on the connection
pins (terminals 3 – 5), via which system messages
from the device may be polled, e.g. using a PLC
(1x change-over contact Basic controller, 2 x normally open contacts Comfort controller).
3.1.5 Condensation
At high levels of humidity and low temperatures inside the enclosure, condensation may form on the
evaporator coil.
The cooling units (except SK 3302.xxx, SK 3303.xxx
and SK 3361.xxx) have automatic, electric condensate evaporation. The thermal component used for
this purpose is based on self-regulating PTC technology. Condensate arising on the evaporator coil
is collected in a tank in the external circuit of the cooling unit, and partially evaporated via the airflow.
When the water level rises, the water enters the PTC
thermal component and is evaporated (through-flow
heater principle). The water vapour streams out of
the cooling unit with the airflow from the external fan.
The PTC thermal component is permanently connected and has no switchpoint. It is protected
against short-circuits with miniature fuses (F1.1,
F1.2). If the fuse has tripped, any condensation is
drained off via the safety overflow.
For unit types SK 3302.xxx, SK 3303.xxx and
SK 3361.xxx, the condensation is routed downwards
out of the unit via a drain pipe on the evaporator coil
divider panel. For this purpose, a hose must be connected to the condensate nozzle (see “4.4 Connecting the condensate drain”, page 11). External condensate evaporators are available as accessories
for these unit types (refer also to the accessories in
the RITTAL Catalogue).
6
3.1.6 Filter mats
The cooling unit condenser is finished all over with a
dirt-repelling, easy-to-clean RiNano coating. In many
cases, therefore, the use of filter media is unnecessary, particularly in the case of dry dusts.
For dry, coarse dust and lint in the ambient air, we
recommend installing an additional PU foam filter
mat (available as an accessory) in the cooling unit.
Depending on the incidence of dust, you will need
to replace the filter from time to time.
For air containing oil condensation, we recommend
the use of metal filters (also available as an accessory). These may be cleaned with suitable detergents
and reused.
Function of the filter mat monitor:
Dirt on the filter mat is automatically determined by
measuring the temperature difference in the external
circuit of the cooling unit. As the level of filter mat soiling rises, the temperature difference will increase.
The nominal value of the temperature difference in
the external circuit adapts automatically to the relevant operating points in the performance diagrams.
Hence there is no need to readjust the nominal value
for different operating points of the cooling unit.
3.1.7 Door limit switch
The cooling unit may be operated with a floating door
limit switch connected. The door limit switch is not included with the supply (available as an accessory,
Model No. PS 4127.000).
The door limit switch function causes the fans and
the compressor in the cooling unit to be switched off
after approximately 15 seconds when the enclosure
door is opened (contacts 1 and 2 closed). This prevents the formation of condensation inside the enclosure while the enclosure door is open. In order to
prevent damage to the unit, it is equipped with an
ON delay: The evaporator fan cuts back in with a delay of approximately 15 seconds after the door has
been closed, while the condenser fan and compressor switch on after approximately 3 minutes.
Note:
– No external voltage must be applied to
the door contacts (terminals 1 and 2).
– For Basic controller cooling units with
230/115 V and 400 V/2-phase connection, the evaporator fan remains operational even with the door open.
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
3.1.8 Additional interface X3
Note:
The electrical signals at the interface are of
an extra-low voltage (not extra-low safety
voltages to EN 60 335).
An additional interface card may be connected to
the 9-pole SUB-D connector X3 in order to incorporate the cooling unit into higher-level monitoring
systems (available as an accessory, interface card
Model No. SK 324.200).
3.2 Proper usage
RITTAL enclosure cooling units were developed and
designed in accordance with the state-of-the-art and
the recognised rules governing technical safety.
Nevertheless, if used improperly, they may pose a
threat to life and limb or cause damage to property.
The unit is only intended for cooling enclosures. Any
other use is deemed improper. The manufacturer will
not be liable for any damages caused as a result of
improper use, or for incorrect assembly, installation
or use. All risk is borne solely by the user.
Proper usage also includes the observation of all
valid documents and compliance with the inspection
and servicing conditions.
3.3 Scope of supply
The unit is supplied in a packaging unit in a fully
assembled state.
Please check the delivery for completeness:
Qty.
Description
1
Enclosure cooling unit
1
1
1
Dispatch bag:
– Assembly and installation instructions
– Assembly, installation and operating
instructions on CD-ROM
– Self-adhesive tape
– Connector X1
– Threaded rods
– Declaration of conformity
– Nuts, washers
1
1
4 – 10
1
1
4
Assembly and connection
EN
4.1 Choosing the installation site
When choosing the installation site for the enclosure,
please observe the following:
– The site for the enclosure, and hence the arrangement of the cooling unit, must be carefully selected
so as to ensure good ventilation (distances between units and distances between the unit and the
wall must be at least 200 mm in each case).
– The cooling unit must be installed and operated in
a vertical position (maximum deviation: 2°).
– The site must be free from excessive dirt and
moisture.
– The ambient temperature must not exceed 55°C.
– It must be possible to fit a condensate discharge
(see “4.4 Connecting the condensate discharge”,
page 11).
– The mains connection data as stated on the rating
plate of the unit must be guaranteed.
4.2 Assembly instructions
4.2.1 General
– Check the packaging carefully for signs of damage.
Traces of oil on damaged packaging are an indication of refrigerant loss and leakages. Packaging
damage may be the cause of a subsequent functional failure.
– The enclosure must be sealed on all sides (IP 54).
Increased condensation will occur if the enclosure
is not airtight.
– In order to avoid excessive condensation inside
the enclosure, we recommend installing a door
limit switch (e.g. PS 4127.000) which deactivates
the cooling unit when the enclosure door is opened
(see “3.1.7 Door limit switch”, page 6).
Drilling template
Tab. 1: Scope of supply
RITTAL cooling unit assembly and operating instructions
7
4 Assembly and connection
EN
4.2.2 Layout of the electronic components
in the enclosure
Caution!
Risk of condensation!
When arranging the components inside
the enclosure, please ensure that the
cold airflow from the cooling unit is not
directed at active components. Please
also ensure that the cold airflow is not
directed at the warm exhaust airflow
from active components such as converters. This may lead to an air shortcircuit and therefore prevent adequate
climate control, or may even cause the
cooling unit’s internal safety devices to
cease cooling operation.
x
Fig. 4:
Air circulation inside the enclosure
4.3 Fitting the cooling unit
The enclosure cooling unit may optionally be externally mounted on the enclosure (1), partially internally mounted (2) or fully internally mounted (3):
1
Fig. 3:
3
Never direct the cold airflow at active components
Air diversion components are available as accessories – please refer to the RITTAL catalogue “System
climate control”.
It is important to ensure even air circulation inside the
enclosure. Under no circumstances should air inlet
and outlet openings be obstructed, otherwise the
cooling performance of the unit will be reduced.
Ensure the distance “x” (see Fig. 4) from electronic
components and other installed enclosures so that
the required air circulation is not obstructed and prevented.
8
2
Fig. 5:
Installation method
To this end, cut the side panel or door of the enclosure as per the drilling template included with the
supply, and drill the relevant holes.
Note:
Units of type SK 3302.xxx can only be either
externally mounted or fully internally mounted.
Units of type SK 3332.xxx can only be either
externally mounted or partially internally
mounted.
For mounting the units SK 3328.xxx,
SK 3329.xxx and SK 3332.xxx in the TS side
panel or rear panel, we recommend the use
of enclosure panel fasteners TS 8800.071
(see RITTAL Catalogue).
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
4.3.1 Cutting out the enclosure
• Stick the supplied drilling template onto the side
panel or door of the enclosure using adhesive
tape.
There are dimensioning lines on the drilling template
to suit the various installation options for your cooling
unit.
• Using the dimension drawings (see Appendix),
identify the valid lines and dimensions for your
installation type on the drilling template.
Risk of injury!
Carefully deburr all drilled holes and
cut-outs to prevent injuries caused by
sharp edges.
EN
Fig. 8:
Secure the cooling unit
(SK 3302.1xx “external mounting” only)
Only for SK 3302.xxx:
• Before installing, remove the four screws as shown.
• Mark, drill and deburr the holes.
• Make the cut-outs including the line width as per
the drilling template.
Deburr the cut-outs.
4x
4.3.2 External mounting of the cooling unit
• Cut the supplied sealing tape to the correct length
and stick it carefully along the back of the unit so
that no gaps are left at the joints.
Fig. 9:
Fig. 6:
Attach the sealing tape
• Screw the supplied grub screws into the blind nuts
on the rear of the unit.
• Secure the unit using the supplied washers and
nuts.
Fig. 7:
Only for SK 3302.xxx: Remove the four screws
4.3.3 Partial internal mounting of the cooling unit
• Carefully remove the louvred grille and, where
applicable, the infill panel, from the enclosure by
pulling forwards.
• Carefully disconnect the connector from the rear of
the display and gently push it inwards through the
cable gland.
Secure the cooling unit
(all models except SK 3302.1xx)
Fig. 10:
RITTAL cooling unit assembly and operating instructions
Remove the louvred grille & disconnect the display
9
4 Assembly and connection
Risk of damage!
Stability of the cooling unit is only
guaranteed in its assembled state.
Brace the rear enclosure half to prevent
it from falling over before removing the
front enclosure half.
EN
• Loosen the four nuts on the front enclosure half and
pull the enclosure forwards by approx. 5 cm.
• Loosen the flat-pin connectors of the PE conductor
between the two enclosure halves.
• Disconnect the fan connection.
• Remove the front enclosure tray completely.
Fig. 13:
Secure the cooling unit
• Connect the fan connector and PE conductor.
• Mount the front enclosure tray using the washers
and nuts.
Fig. 11:
Remove the cover
• Remove the four spacer bolts.
• Cut the supplied sealing tape to the correct length
and stick it carefully along the inside of the rear
enclosure half so that no gaps are left at the connection points.
Fig. 14:
Connect the display connector
• Carefully connect the display connector.
• Push the louvred grille and, where applicable,
the infill panel, onto the enclosure.
Fig. 12:
Attach the sealing tape
• Push the rear enclosure half into the mounting cutout and secure it with the four spacer bolts.
• Push the display cable through the cable gland of
the front enclosure half.
10
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
4.3.4 Full internal mounting of the cooling unit
• Carefully remove the louvred grille and the infill
panel from the enclosure by pulling forwards.
• Carefully disconnect the connector from the rear of
the display.
EN
Fig. 17:
Fig. 15:
Remove the louvred grille and disconnect
the display
• Cut the supplied sealing tape to the correct length
and stick it carefully along the front enclosure half
so that no gaps are left at the connection points.
Fig. 16:
Secure the cooling unit
• Where necessary, additionally secure the unit
using the supplied mounting plates as shown in
Fig. 17.
• Carefully connect the display connector.
• Push the louvred grille and, where applicable,
the infill panel, onto the enclosure.
4.4 Connecting the condensate discharge
Unit types SK 3302.xxx, SK 3303.xxx and
SK 3361.xxx support the installation of a condensate
discharge hose (Ø 1/2˝).
The condensate discharge
– must be laid with a suitable and constant gradient
(no siphoning)
– must be laid without kinks
– must not have a reduced cross-section if extended.
The condensate hose is available as an accessory
(refer also to Accessories in the RITTAL Catalogue).
Attach the sealing tape
• Loosen the four nuts and washers from the front
enclosure half.
• Push the unit into the mounting cut-out from the
inside of the enclosure, and secure it to the enclosure from the outside using the washers and
nuts.
Fig. 18:
Connecting the condensate discharge
• Connect a suitable hose to the condensate nozzle
and secure using a hose clip.
• Lay the condensate hose into a pay-off or into the
external condensate evaporator (refer to accessories in the RITTAL Catalogue).
RITTAL cooling unit assembly and operating instructions
11
4 Assembly and connection
4.5 Notes on electrical installation
EN
When performing the electrical installation, it is important to observe all valid national and regional regulations as well as the provisions of the responsible
power supply company. Electrical installation must
only be carried out by a qualified electrician who is responsible for compliance with the existing standards
and regulations.
4.5.1 Connection data
– The connected voltage and frequency must
correspond to the values stated on the rating plate.
– The cooling unit must be connected to the mains
via an all-pin isolating device, which ensures at
least 3 mm contact opening when switched off.
– No additional temperature control may be connected upstream of the unit at the supply end.
– Install the pre-fuse specified on the rating plate
to protect the cable and equipment from shortcircuits.
– The mains connection must ensure low-noise
potential equalisation.
4.5.2 Overvoltage protection and supply line
load
– The unit does not have its own overvoltage protection. Measures must be taken by the operator at
the supply end to ensure effective lightning and
overvoltage protection. The mains voltage must not
exceed a tolerance of ±10%.
– In accordance with IEC 61 000-3-11, the unit is
intended solely for use at sites with a continuous
current-carrying capacity (incoming mains power
supply) of more than 100 A per phase and with
a supply voltage of 400/230 V. If necessary, the
power supply company must be consulted to
ensure that the continuous current-carrying capacity at the point of connection to the public grid is
sufficient for connection of such a unit.
– The fans and compressors in single- and threephase units are intrinsically safe (thermal winding
protection). The same also applies to the transformer versions of types SK 3304.110, SK 3304.510,
SK 3305.110, SK 3305.510, SK 3328.110,
SK 3328.510, SK 3329.110 and SK 3329.510
and to special-voltage units which are likewise
equipped with a transformer.
– Install the slow pre-fuse specified on the rating
plate (miniature circuit-breaker with “K” characteristic, circuit-breaker for plant or transformer
protection) to protect the cable and equipment from
short-circuits. Select a suitable circuit-breaker in
accordance with the information specified on the
rating plate: Set it to the minimum specified value.
This will achieve the best short-circuit protection for
cables and equipment.
Example: Specified setting range 6.3 – 10 A;
set to 6.3 A.
12
4.5.3 Three-phase devices
– The three-phase version of models SK 3304.xxx,
SK 3305.xxx, SK 3328.xxx, SK 3329.xxx and
SK 3332.xxx must be connected to a TN network
with star earthing via a circuit-breaker for plant
protection (current setting as per the rating plate).
Three-phase units with special voltages must be
protected with a circuit-breaker for transformer
protection (category AC-3) as per the rating plate.
– Units designed for three phase 400/460 V feature
additional monitoring of the rotary field or the
absence of a phase. If the rotary field is incorrect or
a phase is absent, the unit will not run.
4.5.4 Door limit switch
– Each door limit switch must only be assigned to one
cooling unit.
– Several door limit switches may be connected in
parallel and operated on one cooling unit.
– The minimum cross-section for the connection
cable is 0.3 mm2 for a cable length of 2 m.
– The line resistance to the door limit switch must not
exceed a maximum of 50 Ω.
– The door limit switch only supports a floating
connection; no external voltages.
– The contact of the door limit switch must be closed
when the door is open.
The safety extra-low voltage for the door limit switch is
provided by the internal power pack: Current
approx. 30 mA DC.
• Connect the door limit switch to terminals 1 and 2 of
the connector.
4.5.5 Notes on the flicker standard
The flicker limits specified in standard EN 61 000-3-3
or -3-11 are adhered to, provided the supply impedance is less than approx. 1.5 Ω.
Where necessary, the unit operator should measure
the connected impedance or consult the responsible
power supply company. If there is no way of influencing the supply impedance and sensitive installed
components (e.g. BUS) are subjected to interference,
a line reactor or starting-current limiting device should
be connected upstream of the cooling unit to restrict
the startup current of the cooling unit.
4.5.6 Potential equalisation
RITTAL recommends connecting a conductor with a
nominal cross-section of at least 6 mm2 to the potential equalisation connection point on wall-mounted
cooling units, and incorporating it into the existing potential equalisation system.
According to the standard, the PE conductor in the
mains connection cable is not classified as an equipotential bonding conductor.
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
4.6 Carrying out the electrical installation
4.6.1 Bus connection
(only in conjunction with several units
with a Comfort controller)
When using several cooling units, the serial device
interface X2 can be used to connect up to ten cooling units with the bus cable (Model No. SK 3124.100).
4.6.2 Connection X3 for serial interface
The interface card (Model No. SK 3124.200) may be
connected to X3. This is used to evaluate system
messages in a PLC, for remotely setting parameters
and monitoring, or for integration into the facility
management system.
Note:
The electrical signals at the X2 interface are
of an extra-low voltage (not extra-low safety
voltages to EN 60 335-1).
When interconnecting, please note the following:
– De-energise the cooling units to be connected.
– Ensure proper electrical insulation.
– Make sure the cables are not laid in parallel to
power lines.
– Make sure that the lines are short.
Caution!
Regarding the last slave unit in the
group, do not, under any circumstances,
connect the remaining socket of the
Y cable SK 3124.100 into interface X3
of the cooling unit!
RITTAL cooling unit assembly and operating instructions
13
EN
4 Assembly and connection
EN
CMC
1
I/O unit
2
RTT
Master
Adr.: 09
RTT
Slave
Adr.: 11
X3
St. X2
Adr.: 12
X3 Bu.
X2
X3
X2
RTT
Slave
Adr.: 19
X1
X1
X1
X2
RTT
Slave
X1
X3
St. X2
St. X2
X3
X2
St. X2
X2 X2
X2 X2
X2
Bu. St.
Bu. St.
Bu.
3
Fig. 19:
Connection example: Master-slave operation
Legend
1
Serial interface (Model No. SK 3124.200)
2
Serial interface cable
3
Master-slave bus cable (Model No. SK 3124.100)
RTT RITTAL TopTherm cooling units
X1 Supply connection/door limit switch/alarms
X2
X2
Adr.: 06
1
X10 L1
L2
N
X2
Adr.: 11
2
PE 1 2 3 4 5 X10 L1 L2 L3 PE 1 2 3 4 5
L2
N
Master-slave connection Sub-D, 9-pole
Serial interface Sub-D, 9-pole
Sub-D connector, 9-pole
Sub-D jack, 9-pole
Address
X2
Adr.: 12
2
X10 L1
X2
X3
St.
Bu.
Adr.
X2
Adr.: 13
2
PE 1 2 3 4 5
X2
Adr.: 14
2
X10 L1 L2 L3 PE 1 2 3 4 5
X10 L1 L2 L3 PE 1 2 3 4 5
Adr.: 15
2
X10 L1 L2 L3 PE 1 2 3 4 5
X2
L1
L2
N
PE 1 2 3 4 5
X10
Adr.: 16
1 2
3
Fig. 20:
4
5 6
3
2
Connection example: Door limit switch and master-slave operation
Legend
1
Master cooling unit
2
Slave cooling units
3
2-door enclosure with two door limit switches
4
Enclosure with door limit switch
14
4
3
4
4.6.3 Installing the power supply
• Complete the electrical installation by following
the wiring plan on the rear of the cooling unit
(see Fig. 1 on page 5, for key see page 21).
• If you would like the system messages from the
cooling unit to be evaluated via the system
message relay, you should also connect a suitable
low-voltage cable to connection clamps 3 – 5.
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
EN
SK 3302.100/.110, SK 3303.100/.110, SK 3302.200/.210, SK 3303.200/.210,
SK 3302.300/.310, SK 3361.100/.110, SK 3361.200/.210
21
PE
5
Mains
A2
22
S1
L1
X1
L2
N
1
PE
1 2 3
L
N
Power
L1
2
1
3
2
5
4
3
R1
L2
2
1
NTC I red
S1
NTC E blue
Kx
Term
A1
2
B1
2
B2
8
2
F2 1
M2
1 2 3
M1
1 2 3
P
M4
1 2 3
F2
C4
C1
S
R
C2
C
M
M
1~
1~
M2
M4
F3
M1
Fig. 21:
Electrical wiring plan no. 1
21
SK 3303.500/.510, SK 3303.600/.610, SK 3361.500/.510, SK 3361.600/.610
Mains
22
S1
PE
5
L2
N
X1 L1
1
PE
2
3
5
4
X3
X2
3
1 2 3
1
L
N
Power
2
3
S1 K2
2
1
A2
8
MS1
Serial
K1
NTC I red
NTC E blue
Kx
NTC C white
PE
NTC A yellow
Level green
Term
A1
M1
1 2 3
M2
1 2 3
M4
1 2 3
F2
2
1
2
2
2
2
2
B1
B2
B3
B4
B5
4
P
F2
C4
PE
C1
S
R
C
C2
F3
M
M
1~
1~
M2
M4
M1
Fig. 22:
Electrical wiring plan no. 2
RITTAL cooling unit assembly and operating instructions
15
4 Assembly and connection
EN
SK 3361.540/.640
L2
T1
S1
22
400 V
A2
230 V
PE
5
PE
21
L1
L2
N
L1
X1
2
1
PE
4
3
5
X2
X3
3
1 2 3
L
1
N
S1
3
2
2
2
1
Power
B1
NTC I red
Serial
MS1
K1
K2
8
2
B2
NTC E blue
Kx
2
B3
NTC C white
PE
2
B4
NTC A yellow
A1
2
B5
Level green
4
Term
M4
1 2 3
M2
1 2 3
M1
1 2 3
2
1
F2
P
F2
C4
PE
C1
S
R
C2
M
C
F3
M
1~
1~
M2
M4
M1
Fig. 23:
Electrical wiring plan no. 3
21
SK 3304.100/.200
Mains
22
S1
PE
5
X1
L1
L2
L1
PE
N
1
2
3
5
4
L1
F11
L2
R1
L2
A2
E1
T1
L
N
1 2 3
PE
1
L
N
Power
2
3
2
1
NTC I red
S1
NTC E blue
Kx
Term
2
2
B1
B2
8
A1
F2
M2
1 2 3
M1
1 2 3
2
1
P
F2
M4
1 2 3
C1
C4
1
R
S
C2
F3
3
M1
Fig. 24:
16
M
M
1~
1~
M2
M4
C
Electrical wiring plan no. 4
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
EN
21
SK 3305.100/.110, SK 3328.100/.110, SK 3329.100/.110, SK 3305.200/.210,
SK 3328.200/.210, SK 3329.200/.210, SK 3366.100/.110, SK 3377.100/.110,
SK 3366.200/.210, SK 3377.200/.210
Mains
22
S1
PE
5
L1
L2
N
L1
X1
1
PE
2
3
5
4
L1
F11
L2
R1
L2
A2
E1
T1
L N
1 2 3
PE
1
L
N
Power
2
3
2
1
S1
M2
1 2 3
M1
1 2 3
F2
C4
4
C12
1
C11
2
5
C2
Fig. 25:
P
1
M4
1 2 3
A3
R
P
F3
8
2
F2
A
B2
Term
A1
B1
2
NTC E blue
Kx
C
2
NTC I red
M1
M
M
1~
1~
M2
M4
Electrical wiring plan no. 5
21
SK 3304.140, SK 3304.142, SK 3305.140, SK 3305.142, SK 3328.140, SK 3329.140,
SK 3304.240, SK 3305.240, SK 3328.240, SK 3329.240, SK 3366.140/.240, SK 3377.140/.240
Mains
22
S1
PE
5
X1
L1
L2
L3
PE
1
2
3
4
5
L1
F11 F12
T1
A2
E1
3
PE
R
2
1
1
S
T
Power
R1
L2
2
2
4
1
3
S1
NTC I red
NTC E blue
Kx
Term
2
2
B1
B2
8
A1
M1
1 2 3 4
F3
F2
M2
F4
1 2 3 4 1 2 3
1 2 3 4
M4
F5
1 2 3
1 2
P
F2
U
V
M
F3
W
M
3~
3~
M2
M4
M1
Fig. 26:
Electrical wiring plan no. 6
RITTAL cooling unit assembly and operating instructions
17
4 Assembly and connection
EN
21
SK 3304.700, SK 3328.700
S1
22
Mains
PE
L1 L2
N
5
L1
X1 L1
T1
F12
PE
N
1
2
3
A2
5
4
L1
F11
L1 L2/N
F11
L2
R1
L2
E1
E1
1 2 3
123
L N
Power
PE
1
2
3
2
1
2
NTC I red
Kx
B2
8
Term
A1
B1
2
NTC E blue
S1
2
F2
P F2
1
M2
1 2 3
M1
1 2 3
A
C1.2
P
F3
Fig. 27:
A3
4
1
R
C
M4
1 2 3
C1.1
2
5
M1
M
1~
M
1~
M2
M4
Electrical wiring plan no. 7
21
SK 3304.800, SK 3328.800
Mains
S1
22
L1 L2
N
PE
L1
5 T1
L1 L2/N
F11
F12
X1 L1 L2
N
PE 1
E1 F11
X2
2
3
5 3
4
A2
X3
PE 6 PE
E1
1 2 3
123
L N
Power
1
S1
2 3
K2
2
1
K1
Kx
Serial NTC I red
NTC E blue
NTC C white
NTC A yellow
A1
Level green
Term
M2
1 2 3
M1
1 2 3
2
2
2
2
2
B1
B2
B3
B4
B5
4
2
F2
M4 1
1 2 3
P
F2
A
C
C1.2
P
F3
M1
Fig. 28:
18
R
C1.1
A3
4
1
2
5
M
1~
M
1~
M2
M4
Electrical wiring plan no. 8
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
EN
21
SK 3304.500/.600
S1
Mains
22
PE
X2
5
X1
L2
L1
L1
L2
L
N
1
PE
N
2
3
X3
A2
5
4
3
6
F11
T1
E1
PE
1 2 3
1
L
S1
N
2
3
2
1
MS1
2
NTC I red
Serial
Power
K1
K2
M4
1 2 3
F2
B5
4
Term
M2
1 2 3
B4
2
Level green
M1
1 2 3
B3
2
NTC A yellow
A1
B2
2
NTC C white
Kx
B1
2
NTC E blue
2
1
P
F2
C1
C4
1
R
S
C2
F3
3
M
1~
M2
M4
C
M1
Fig. 29:
M
1~
Electrical wiring plan no. 9
21
SK 3305.500/.510, SK 3328.500/.510, SK 3329.500/.510, SK 3305.600/.610, SK 3328.600/.610,
SK 3329.600/.610, SK 3366.500/.510, SK 3377.500/.510, SK 3366.600/.610, SK 3377.600/.610
PE
A2
Mains
X2
S1
22
5
X3
6
3
L2
N
L1
X1
L2
N
L1
1
PE
2
3
5
4
F11
T1
E1
1 2 3
L
1
2
N
3
2
K2
1
MS1
NTC I red
Serial
K1
2
S1
Power
2
NTC E blue
Kx
NTC C white
2
2
NTC A yellow
A1
Level green
Term
M1
1 2 3
M4
M2
1 2 3
1 2 3
F2
2
B1
B2
B3
B4
B5
4
2
P
1
F2
A3
A
R
C
4
C12
P
C11
C4
1
2
5
C2
F3
Fig. 30:
M1
M
M
1~
1~
M2
M4
Electrical wiring plan no. 10
RITTAL cooling unit assembly and operating instructions
19
4 Assembly and connection
EN
SK 3304.540, SK 3304.542, SK 3305.540, SK 3305.542, SK 3328.540, SK 3329.540, SK 3304.640,
SK 3305.640, SK 3328.640, SK 3329.640, SK 3366.540, SK 3377.540, SK 3366.640, SK 3377.640
Mains
22
PE
X1
L1
L2
L3
1
PE
2
3
4
S1
21
5
X3
X2
5
3
F11 F12
8
A2
E1
T1
3
2
1
1 2
Power
2
4
1
K2
3
MS1
2
NTC I red
Serial
K1
S1
F3
1 2 3 4
1 2 3 4
F4
M2
1 2 3 4 1 2 3
M4
F5
1 2 3
1 2
B5
4
Term
F2
B4
2
Level green
M1
B3
2
NTC A yellow
A1
B2
2
NTC C white
Kx
B1
2
NTC E blue
P
F2
U
V
M
M
F3
W
3~
3~
M2
M4
M1
Fig. 31:
Electrical wiring plan no. 11
21
SK 3332.140/.240
Mains
S1
22
PE
6
A2
L1
X1
L2
L1
L3 PE
1
2
3
4
R1
L2
5
F11 F12
8
T1
E1
3
R
2
S
1
1
T
2
2
4
1
3
NTC I red
Term
S1
NTC E blue
Power
2
2
B1
B2
Kx
A1
M1
F3
1 2 3 4
1 2 3 4
U
V
F2
M2
1
1 2
3
F5
1 2 3 1
2
F2
P
W
M4
F4
2 3 4
M
M
3~
3~
M2
M4
M1
Fig. 32:
20
Electrical wiring plan no. 12
RITTAL cooling unit assembly and operating instructions
4 Assembly and connection
EN
21
SK 3332.540/.640
S1
22
Mains
A2
PE
X1
6
L1
L2
L3
PE
1
2
3
X3
X2
5
4
3
8
F11 F12
E1
T1
3
R
2
S
1
1
2
2
4
1
3
MS1
T
K2
NTC I red
Serial
NTC E blue
S1
Power
2
2
K1
NTC C white
Kx
2
2
NTC A yellow
Level green
A1
Term
M1
F3
1 2 3 4
1 2 3
U
V
F2
F4
M2
4
1
2
3 4
1 2 3
M4
F5
1 2 3
1
2
B1
B2
B3
B4
B5
4
2
F2
M
M
P
3~
3~
M2
M4
W
M1
Fig. 33:
Electrical wiring plan no. 13
Legend
A1
A2
A3
B1
B2
B3
B4
B5
C1 – C4
E1
F2
Power PCB
Basic or Comfort controller
Starter relay and RC element
Temperature sensor, internal temperature
Icing hazard temperature sensor
Temperature sensor, external 1
Temperature sensor, external 2
Condensate warning sensor (optional)
Running capacitors
Condensate evaporator
PSAH pressure-operated switch
(3302.1x0 has bridge instead of pressostat)
F3
Bimetal contact compressor
F11/F12 Miniature fuses, condensate evaporator
K1
Relay collective fault 1
K2
Relay collective fault 2
L1
LED operational green
L2
LED alarm red
M1
Compressor
M2
Condenser fan
M4
Evaporator fan
R1
Potentiometer for setting the temperature
S1
Door limit switch
(without door limit switch: terminal 1, 2 open)
T1
Transformer (optional)
X1
Main terminal strip
X2
Master-slave connection
X3
Optional interface
RITTAL cooling unit assembly and operating instructions
Note:
For technical data refer to the rating plate.
AC
DC
cos f = 1
L/R = 20 ms
I max. = 2 A
U max. = 250 V
I min. = 100 mA
U max. = 200 V
U min. = 18 V
I max. = 2 A
Tab. 2: Contact data
21
5 Commissioning
4.7 Finalising assembly
EN
4.7.1 Installing the filter media
The cooling unit condenser is finished all over with a
dirt-repelling, easy-to-clean RiNano coating. In many
cases, therefore, the use of filter media is unnecessary, particularly in the case of dry dusts.
For dry, coarse dust and lint in the ambient air, we
recommend installing an additional PU foam filter
mat (available as an accessory) in the cooling unit.
For air containing oil condensation, we recommend
the use of metal filters (also available as an accessory). When used in textile plants with heavy lint contamination, lint screens should be used (available as
an optional extra).
• Pull the louvred air inlet grille from the enclosure.
• Insert the filter mat into the louvred grille as shown
in Fig. 34 and push it back onto the enclosure.
4.7.3 Setting the filter mat monitor
(only with Comfort controller)
Function of the filter mat monitor:
Dirt on the filter mat is automatically detected by
measuring the temperature difference in the external
circuit of the cooling unit (see “6.2.5 Programming
overview”, page 28). As the level of filter mat soiling
rises, the temperature difference will increase. The
nominal value of the temperature difference in the
external circuit adapts automatically to the relevant
operating points in the performance diagrams.
Hence there is no need to readjust the nominal value
for different operating points of the cooling unit.
5
Commissioning
Caution! Risk of damage!
The oil must collect in the compressor in
order to ensure effective lubrication and
cooling.
Do not operate the cooling unit for
at least 30 min. after assembling the
equipment.
Fig. 34:
Installing the filter mat
4.7.2 Fitting the cooling unit
For partial and full internal mounting only.
• Connect the connector to the rear of the display.
• Place the louvred grille onto the unit at the front,
and press it down until you hear it snap into place.
Fig. 35:
22
• Once all the assembly and installation work is complete, switch on the power supply to the cooling
unit.
The cooling unit starts running:
– With Basic controller: The green operating LED
(“line”) is illuminated.
– With Comfort controller: The software version of the
controller first appears for approx. 2 sec., then
the enclosure internal temperature appears in the
7-segment display.
You can now make your individual settings on the
unit, e.g. set the temperature or (with Comfort controller only) assign the network identifier, etc. (refer to
the “Operation” chapter).
Connect the display and attach the louvred grille
RITTAL cooling unit assembly and operating instructions
6 Operation
6
Operation
You can operate the cooling unit using the controller
on the front of the device (Fig. 1, no. 11, page 5).
Depending on the model, the unit is equipped with
a Basic or Comfort controller.
6.1 Control using the Basic controller
For unit types SK xxxx.100/.110/.140 and
SK xxxx.200/.210/.240/.300/.310.
1
3
4
2
5
Fig. 36:
Basic controller
Legend
1
Controller trim panel
2
Temperature setting
3
LED green (“line”)
4
LED red (“alarm”)
5
Reset button
RITTAL cooling unit assembly and operating instructions
6.1.1 Properties
– Three voltage variants are supported:
– 115 V
– 230 V
– 400/460 V, 3-phase
– Supports multiple voltages without rewiring
– Integral start-up delay and door limit switch
function
– Protective function to prevent icing
– Monitoring of all motors (compressor,
condenser fan, evaporator fan)
– Phase monitoring for three-phase units
– Visualisation of the operating status via LED
display:
– Voltage on, unit operational
– Door open (only if door limit switch installed)
– Warning of overtemperature
– High-pressure-operated switch has switched
– Switching hysteresis: 5 K
– Floating system message contact in case
of overtemperature
– Temperature setting
(setting range 30 – 55°C) via potentiometer
– Test function
EN
The cooling unit operates automatically i.e. after
switching on the power supply, the evaporator fan
(see Fig. 2, page 5) will run continuously and permanently circulate the internal enclosure air. The built-in
Basic controller ensures automatic normal shutdown operation of the cooling unit by the value of the
fixed preset switching difference of 5 K.
23
6 Operation
EN
6.1.2 Operating and error display
The Basic controller monitors and controls the cooling unit. It indicates the operating and error status via
the green and red LEDs (Fig. 36, no. 3 and 4):
LED
Status
Cause
Solution
Green
(line)
Illuminated
Voltage present,
unit operational
–
Flashing
Only with door limit switch installed:
Enclosure door open
In order to avoid condensation, close the
enclosure door as quickly as possible.
Only with door limit switch installed:
Enclosure door closed
Check the position of the door limit switch.
Red
(alarm)
Alarm/error/warning
Number of
flash intervals
for the red
LED
Flash interval
Implement
a reset
Device reset
(12)
|_|_|_|_|_|_|_|_|_|_|_|*****|_|_|_|_|_|_|_|_|_|_|_|
High pressure alarm
(0)
|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|
Sensors
Potentiometer defective
or display error
(3)
|_|_|*****|_|_|*****|_|_|*****|_|_|*****|_|_|*****
Interior temperature
sensor defective
(4)
|_|_|_|*****|_|_|_|*****|_|_|_|*****|_|_|_|*****
Anti-icing sensor
defective
(5)
|_|_|_|_|*****|_|_|_|_|*****|_|_|_|_|*****|_|_|_|_|
Compressor overloaded
(6)
|_|_|_|_|_|*****|_|_|_|_|_|*****|_|_|_|_|_|*****
Interior fan overloaded
(7)
|_|_|_|_|_|_|*****|_|_|_|_|_|_|*****|_|_|_|_|_|_|
Exterior fan overloaded
(8)
|_|_|_|_|_|_|_|*****|_|_|_|_|_|_|_|*****
Device
status/
condition
Overload mode
(heat loss)
(9)
|_|_|_|_|_|_|_|_|*****|_|_|_|_|_|_|_|_|*****
Low load mode
(heat loss)
(11)
|_|_|_|_|_|_|_|_|_|_|*****|_|_|_|_|_|_|_|_|_|_|
Warning
(ambient
conditions)
Anti-icing alarm
(2)
|_|*****|_|*****|_|*****|_|*****|_|*****|_|*****|_|
Overtemperature
warning
(1)
|*****|*****|*****|*****|*****|*****|*****|*****|*****|
No
display
No power
–
Check power supply
Rotary current phase
monitoring:
“LED off” = Incorrect
phase connection
–
Swap phases
Overload
Off
Tab. 3: Operating and error display of the Basic controller
Key to flash intervals
|
= 500 ms (red LED on)
_
= 500 ms (red LED off)
***** = 3 s pause (red LED off)
24
RITTAL cooling unit assembly and operating instructions
6 Operation
The overtemperature message (red LED illuminated)
may also be polled via an integral floating contact on
the connection clamp of the cooling unit (system
message relay with changeover contact, see connection diagrams under “4.6.3 Installing the power
supply”, page 14):
– Terminal 3: NC (normally closed)
– Terminal 4: C (connection of the supply voltage
to the system message relay)
– Terminal 5: NO (normally open)
The NC and NO definitions refer to the de-energised
state. As soon as power is applied to the cooling unit,
the system message relay picks up, so that the relay
contacts change status (contact 3 – 4 open; contact
4 – 5 closed). This is the normal operating state of the
cooling unit. As soon as an error message occurs or
the power supply is interrupted, the relay drops out
and contact 3 – 4 is closed.
6.1.3 Test mode for the Basic controller
The Basic controller is equipped with a test function
whereby the cooling unit commences cooling operation independently of the set temperature or door
limit switch function.
First you must dismantle the trim panel of the controller.
• Switch off the mains voltage.
• Remove the louvred grille or infill panel in which the
controller is installed.
• Release the display lock from behind and pull it
forwards slightly.
Fig. 37:
Loosen the trim panel of the Basic controller
• Carefully raise the trim panel, e.g. using your
thumb or a flat screwdriver, and remove it.
You can now start test mode.
• Rotate the potentiometer to the left-hand stop, then
hold the rubberised potentiometer display down
while you re-connect the mains voltage.
RITTAL cooling unit assembly and operating instructions
The cooling unit will commence operation and the
green LED will flash (I_II_I_II_ . . .). Test mode is
completed after approximately 5 minutes. The unit
switches off and changes to normal operation.
Key
I = LED 500 ms on
_ = LED 500 ms off
In normal operation, the green LED is permanently
illuminated.
• Next, rotate the potentiometer back to the required
setpoint.
6.1.4 Setting the temperature
Note:
With the Basic controller, the temperature
is preset at the factory to +35°C.
In order to save energy, do not set the
temperature any lower than is actually
necessary.
To change the temperature setting:
• Dismantle the trim panel of the controller as
described in “6.1.3 Test mode for the Basic
controller”, page 25.
• Set the required temperature on the temperature
setting device (Fig. 36, page 23).
• Carefully push the trim panel onto the display until
you hear it snap into place.
• Push the display back into the infill panel or louvred
grille.
• Re-attach the louvred grille or infill panel to the
cooling unit.
6.1.5 Resetting the Basic controller
Following a high-pressure alarm in the cooling cycle,
and once the cause has been rectified, you will need
to manually reset the Basic controller:
• Dismantle the trim panel of the Basic controller
as described in “6.1.3 Test mode for the Basic
controller”, page 25.
• Press the reset button (Fig. 36, no. 5) for at least
3 sec.
The red LED is extinguished.
• Re-install the Basic controller.
25
EN
6 Operation
6.2 Control using the Comfort controller
EN
For unit types SK xxxx.500/.510/.540 and
SK xxxx.600/.610/.640.
1
4
Fig. 38:
2
3
Comfort controller
Legend
1
Programming button, also display of the set
temperature unit (degrees Celsius)
2
Set button
3
Programming button, also display of the set
temperature unit (degrees Fahrenheit)
4
7-segment display
6.2.1 Properties
– Three voltage variants are supported:
– 115 V
– 230 V
– 400/460 V, 3-phase
– Supports multiple voltages without rewiring
– Integral start-up delay and door limit switch
function
– Protective function to prevent icing
– Monitoring of all motors (compressor,
condenser fan, evaporator fan)
– Phase monitoring for three-phase units
– Master-slave function with a maximum of ten units.
One device functions as a master unit. Once the
set temperature is reached by one of the connected slave devices or in the event of the door limit
switch function, the affected slave unit will report
to the master unit, which will switch all the other
cooling units on or off as required.
– Switching hysteresis: Adjustable within the range
2 – 10 K, preset to 5 K.
– Visualisation of the current enclosure internal temperature and all error messages in the 7-segment
display.
– Using an interface card (Model No. SK 3124.100),
the unit may be incorporated into higher-level
remote monitoring systems such as the RITTAL
Computer Multi Control CMC.
The cooling unit operates automatically i.e. after
switching on the power supply, the evaporator fan
(see Fig. 2, page 5) will run continuously and permanently circulate the internal enclosure air. The
compressor and condenser fan are regulated by the
Comfort controller.
The Comfort controller has a 7-segment display
(Fig. 38, no. 4). After switching on the power supply,
the current software version is initially displayed for
approximately 2 sec., followed by a preset option
(e.g. t10) or the temperature.
In regular operation, the display shows both the temperature (in degrees Celsius or Fahrenheit – users
may switch between the two) and any error messages.
The current enclosure internal temperature is usually
displayed permanently. In the event of an error message, this will alternate with the temperature display.
The unit is programmed using buttons 1 – 3 (Fig. 38).
The relevant parameters also appear in the display.
6.2.2 Launching test mode
The Comfort controller is equipped with a test function whereby the cooling unit commences cooling
operation independently of the set temperature or
door limit switch function.
• Simultaneously press buttons 1 and 2 (Fig. 38)
for at least 5 sec.
The cooling unit will commence operation.
After approximately 5 minutes, test mode will end.
The unit switches off and changes to normal operation.
6.2.3 General programming information
Using buttons 1, 2 and 3 (Fig. 38) you can change
24 parameters within the preset ranges (min. value –
max. value).
Tables 4 and 5 show the parameters which can be
altered. Fig. 39 of page 28 shows which buttons
must be pressed.
Note on switching hysteresis:
With a low hysteresis and short switching
cycles, there is a risk that cooling may not
be adequate or that only partial sections
of the enclosure are cooled.
Note on temperature settings:
With the Comfort controller, the temperature
is preset at the factory to +35°C.
In order to save energy, and due to the
risk of increased condensation, do not set
the temperature lower than that actually
necessary.
Note on useful cooling output:
Interactive performance diagrams for
calculating the useful cooling output may
be found at www.rittal.com.
26
RITTAL cooling unit assembly and operating instructions
6 Operation
In principle, the programming is identical for all
editable parameters.
To enter programming mode:
• Press button 2 (“Set”) for approx. 5 sec.
The controller is now in programming mode. While in
programming mode, if you do not press any buttons
for approx. 30 sec., the display will first flash, then
the controller will switch back to normal display
mode. The “Esc” display indicates that any made
changes have not been saved.
• Press the programming buttons ▲ (°C) or ▼ (°F)
to switch back and forth between the editable
parameters (see tables 4 and 5).
• Press button 2 (“Set”) to select the displayed
parameter for editing.
The current value of this parameter is displayed.
• Press one of the programming buttons ▲ (°C) or
▼ (°F).
The “Cod” display will appear. In order to be able to
change a value, you must enter the authorisation
code “22”.
• Keep the programming button ▲ (°C) held down
until “22” appears.
• Press button 2 (“Set”) to confirm the code.
You can now alter the parameter within the preset
limits.
• Press one of the programming buttons ▲ (°C) or
▼ (°F) until the required value appears.
• Press button 2 (“Set”) to confirm the change.
You can now alter other parameters in the same way.
There is no need to re-enter the authorisation code
“22”.
• To exit programming mode, press button 2 (“Set”)
again for approximately 5 sec.
“Acc” will appear in the display to indicate that the
changes have been saved. The display will then
switch back to regular operation (enclosure internal
temperature).
You can also program the Comfort controller
using a diagnosis software package (Model No.
SK 3159.100), the supply of which also includes
a connection cable to the PC. The cable connector
on the rear of the Comfort controller display serves
as an interface.
6.2.4 Editable parameters
See also Fig. 39 on page 28.
Progr.
level
Display
screen
Parameter
Min.
value
Max.
value
Factory
setting
Description
1
St
Internal enclosure
temperature
setpoint Ti
20
55
35
The setting of the enclosure internal temperature
is preset at the factory to 35°C and may be altered
within a range of 20 – 55°C.
2
Fi
Filter mat
monitoring
10
60
99
(= off)
To activate filter mat monitoring, set the display to
at least 10 K above the temperature differential
displayed in programming mode “Fi”. Filter mat
monitoring is preset to “deactivated” in the factory
(99 = off).
3
Ad
Master-slave
identifier
0
19
0
See “6.2.7 Setting the master-slave identifier”,
page 30.
4
CF
Temperature
conversion
°C/°F
0
1
0
The temperature display can be switched from
°C (0) to °F (1). The corresponding LED displays
the current unit of temperature.
5
H1
Setting for
switching
difference
(hysteresis)
2
10
5
The cooling unit is preset in the factory to a
switching hysteresis of 5 K. This parameter should
only be changed in consultation with us.
Please contact us for advice.
6
H2
Differential for
error message A2
3
15
5
If the internal enclosure temperature exceeds the
set value by more than 5 K, then error message
A2 (enclosure internal temperature too high)
appears on the display terminal. If necessary,
the differential may be altered here within the
range of 3 – 15 K.
Tab. 4: Editable parameters
RITTAL cooling unit assembly and operating instructions
27
EN
6 Operation
6.2.5 Programming overview
= 5 sec.
= 5 sec.
EN
Fig. 39:
28
Programming overview
RITTAL cooling unit assembly and operating instructions
6 Operation
6.2.6 Defining system messages for evaluation
System messages are shown on the display screen
of the Comfort controller via the displays A1 to A20
and E0.
A more detailed explanation of the system messages
may be found in section “6.2.8 Evaluating system
messages”, page 30.
See also Fig. 39 on page 28.
Progr.
level
Display
screen
Min.
value
Max.
value
Factory
setting
Type or location of fault
7
A1
0
2
0
Enclosure door open
8
A2
0
2
0
Internal temperature of enclosure too high
9
A3
0
2
0
Filter monitoring
10
A4
0
2
0
Ambient temperature too high/too low
11
A5
0
2
0
Icing hazard
12
A6
0
2
1
PSAH pressure-operated switch
13
A7
0
2
2
Evaporator coil
14
A8
0
2
1
Condensate warning
15
A9
0
2
1
Condenser fan blocked or defective
16
A10
0
2
1
Evaporator fan blocked or defective
17
A11
0
2
2
Compressor
18
A12
0
2
1
Condenser
19
A13
0
2
1
Ambient temperature sensor
20
A14
0
2
1
Icing temperature sensor
21
A15
0
2
1
Condensate warning temperature sensor
22
A16
0
2
1
Internal temperature sensor
23
A17
0
2
1
Phase monitoring
24
A18
0
2
0
EPROM
25
A19
0
2
0
LAN/Master-Slave
Tab. 5: System messages which may be evaluated via relays
The system messages A1 – A19 may additionally be
evaluated via two floating system message relays. In
this way, one of the two system message relays may
be allocated to each system message.
System alarm relay with normally open contact: see
connection diagrams under “4.6.3 Installing the
power supply”, page 14:
– Terminal 3: NO (normally open, relay 2)
– Terminal 4: C (connection of the supply voltage
to the system message relay)
– Terminal 5: NO (normally open, relay 1)
This is the normal operating state of the cooling unit.
As soon as a system message occurs or the power
supply is interrupted, the corresponding relay will
drop out and open the contact.
Program system messages with the value
0: System message is not sent to the system
message relay, but merely appears in the
display
1: System message is evaluated by relay 1
2: System message is evaluated by relay 2
The definition NO refers to the de-energised state.
As soon as power is applied to the cooling unit, both
system message relays (relay 1 and 2) energise.
RITTAL cooling unit assembly and operating instructions
29
EN
6 Operation
EN
6.2.7 Setting the master-slave identifier
When several cooling units are connected together
(maximum ten), one of the cooling units must be
defined as the “master” and the others as “slaves”.
For this purpose, assign a corresponding identifier
(address) to each cooling unit which will enable the
cooling unit to be identified in the network.
If one of the slave units reaches the set temperature
or if the door limit switch function is activated, the
affected slave unit will report to the master unit,
which then deactivates all the other cooling units.
Notes:
– Only one unit may be configured as
master, and its identifier must match the
number of slave units connected.
– The slave units must have different
identifiers.
– The identifiers must be numbered in
ascending order without any gaps.
On the master cooling unit (00 = factory setting),
set the number of slave units present in the network:
01: Master with 1 slave cooling unit
02: Master with 2 slave cooling units
03: Master with 3 slave cooling units
04: Master with 4 slave cooling units
05: Master with 5 slave cooling units
06: Master with 6 slave cooling units
07: Master with 7 slave cooling units
08: Master with 8 slave cooling units
09: Master with 9 slave cooling units
30
On the slave cooling unit (00 = factory setting),
set its own address:
11: Slave cooling unit no. 1
12: Slave cooling unit no. 2
13: Slave cooling unit no. 3
14: Slave cooling unit no. 4
15: Slave cooling unit no. 5
16: Slave cooling unit no. 6
17: Slave cooling unit no. 7
18: Slave cooling unit no. 8
19: Slave cooling unit no. 9
Master
02
Fig. 40:
Slave
11
Slave
12
Master-slave connection (example)
For further connection examples, see “4.6.1 Bus
connection (only in conjunction with several units
with a Comfort controller)”, page 13.
For details of how to set the identifier, see “6.2.4
Editable parameters”, page 27 or “6.2.5 Programming overview”, page 28, parameter “Ad”.
6.2.8 Evaluating system messages
In the Comfort controller, system messages are indicated by a number in the display.
Following the appearance of messages A03, A06
and A07 and after rectifying their cause, you will
need to reset the Comfort controller (see “6.2.9 Resetting the Comfort controller”, page 32).
RITTAL cooling unit assembly and operating instructions
6 Operation
Display
screen
A01
System message
Possible cause
Measures to rectify the fault
Enclosure door open
Door open or door limit switch
incorrectly positioned
Close door, position door limit switch correctly,
check connection if necessary
A02
Internal temperature
of enclosure too high
A03
Filter monitoring
A04
Ambient temperature
too high/too low
Icing hazard
Cooling capacity inadequate/unit undersized. Check cooling capacity
Error as a consequence of messages A03 to
A17.
Filter mat soiled
Clean or replace;
reset the Comfort controller
Ambient temperature outside of admissible Raise or lower the ambient temperature
operating range (+10°C to +60°C)
(e.g. heat or ventilate the room)
Operational display in case of icing hazard. Set the enclosure interior temperature to
Evaporator coil fan may be mechanically
a higher value. Check the evaporator fan;
blocked, defective, or cold air outlet
release or exchange if necessary.
obstructed.
Ambient temperature too high
Lower the ambient temperature;
reset the Comfort controller
Condenser soiled
Clean the condenser;
reset the Comfort controller
Filter mat soiled
Clean or replace;
reset the Comfort controller
Condenser fan defective
Replace;
reset the Comfort controller
E-valve defective
Have the sensor repaired by a refrigeration
engineer; reset the Comfort controller
Have the switch replaced by a refrigeration
PSAH pressure-operated switch defective
engineer; reset the Comfort controller
Lack of coolant; sensor in front of or behind Have the sensor repaired by a refrigeration
condenser defective.
engineer; reset the Comfort controller
Condensate discharge kinked or blocked
Check condensate discharge; repair any kinks
or blockages in the hose as necessary
Only in units with optional
Check the evaporation unit,
condensate evaporation
exchange if necessary
Blocked or defective
Clear the blockage; replace if necessary
Blocked or defective
Clear the blockage; replace if necessary
Compressor overloaded
No action required;
(internal winding protection)
unit switches back on automatically.
Defective
Exchange by refrigeration engineer
(check by measuring the winding resistance)
Open or short-circuit
Replace
A05
A06
PSAH pressure-operated
switch
A07
Evaporator coil
A08
Condensate warning
A09
A10
A11
Condenser fan
Evaporator fan
Compressor
A12
A16
A17
Condenser temperature
sensor
Ambient temperature
sensor
Icing temperature sensor
Condensate warning
temperature sensor
Internal temperature sensor
Phase monitoring
A18
EPROM error
A19
A20
E0
LAN/Master-Slave
Voltage drop
Display message
OL
LH
rSt
Overload
Low heat
Reset
A13
A14
A15
Open or short-circuit
Replace
Open or short-circuit
Open or short-circuit
Replace
Replace
Open or short-circuit
For three-phase devices only:
Incorrect rotary field/phase absent
New board obstructed
Replace
Exchange two phases
Software update needed (only following board
installation with more recent software):
Enter the programming level with Code 22;
press button 1 and confirm with “Set” until
“Acc” appears. Next, disconnect the unit from
the mains and reconnect.
Master and slave not connected
Check setting and/or cable
Error display not shown
Event is stored in the log file
Connection problem between the display
Reset: Switch power supply off, then switch
and the controller board
on again after approx. 2 sec.
Cable defective; connection loose
Exchange the boards
Ambient parameters or heat loss outside of the applicable limits
Minimal heat loss inside the enclosure
Manual device reset required,
see “6.2.9 Resetting the Comfort controller”, page 32.
Tab. 6: Troubleshooting with the Comfort controller
RITTAL cooling unit assembly and operating instructions
31
EN
7 Inspection and maintenance
EN
6.2.9 Resetting the Comfort controller
After the occurrence of faults A03, A06 and A07,
you will need to reset the Comfort controller.
• Press buttons 1 (▲) and 3 (▼) (Fig. 38) simultaneously for 5 sec.
The system messages will disappear and the temperature display will be shown.
7
7.1.1 Compressed air cleaning
SK 3304.xxx, SK 3305.xxx
Inspection and maintenance
Risk of electric shock!
The unit is live.
Switch off the power supply before opening, and take suitable precautions against
it being accidentally switched back on.
Fig. 41:
Disconnect the power cord
Fig. 42:
Remove the upper louvred grille
7.1 General
The cooling circuit is designed in the form of a maintenance-free, hermetically sealed system. The cooling unit is filled with the required quantity of refrigerant at the factory, checked for leaks, and subjected
to a functional test run.
The installed maintenance-free fans are mounted on
ball bearings, protected against moisture and dust,
and fitted with a temperature monitor. The life expectancy is at least 30,000 operating hours. The cooling
unit is thus largely maintenance-free. All that may be
required from time to time is to clean the components
of the external air circuit using a vacuum cleaner or
compressed air if they become visibly dirty. Any
stubborn, oily stains may be removed using a nonflammable detergent, such as degreaser.
Maintenance interval: 2000 operating hours. Depending on the level of contamination in the ambient air,
the maintenance interval may be reduced to suit the
air pollution intensity.
Caution!
Risk of fire!
Never use flammabel liquids
for cleaning.
Sequence of maintenance measures:
– Check the level of dirt.
– Filter soiling? Replace the filter if necessary.
– Cooling membranes soiled? Clean if necessary.
– Activate test mode; cooling function OK?
– Check noise generation of compressor and fans.
32
RITTAL cooling unit assembly and operating instructions
7 Inspection and maintenance
EN
Fig. 43:
Fig. 44:
Remove the lower louvred grille
Fig. 45:
Disconnect the connector from the display (1)
Fig. 46:
Disconnect the connector from the display (2)
Remove the infill panel
RITTAL cooling unit assembly and operating instructions
33
7 Inspection and maintenance
EN
Fig. 50:
Disconnect the fan connectors
Fig. 47:
Cooling unit without grille
Fig. 51:
Remove the cover (loosen the four screws)
Fig. 48:
Remove the external circuit fan
(loosen the four screws)
Fig. 52:
Push back the display cable
Fig. 49:
Remove the fan
Fig. 53:
Push the display cable through the cable gland
34
RITTAL cooling unit assembly and operating instructions
7 Inspection and maintenance
EN
Fig. 54:
Fig. 55:
Fig. 56:
Loosen the earthing cable between the cover
and the chassis (1)
Fig. 57:
Loosen the earthing cable between the cover
and the chassis (2)
Fig. 58:
Clean out the heat exchanger coil and compressor
chamber using compressed air (1)
Remove the cover (1)
Remove the cover (2)
RITTAL cooling unit assembly and operating instructions
35
7 Inspection and maintenance
EN
Fig. 59:
Clean out the heat exchanger coil and compressor
chamber using compressed air (2)
Fig. 61:
Remove the upper louvred grille (1)
Fig. 62:
Remove the upper louvred grille (2)
7.1.2 Compressed air cleaning
SK 3328.xxx, SK 3329.xxx, SK 3332.xxx
Fig. 60:
36
Disconnect the power cord
RITTAL cooling unit assembly and operating instructions
7 Inspection and maintenance
EN
Fig. 63:
Remove the upper louvred grille (3)
Fig. 65:
Remove the lower louvred grille (2)
Fig. 64:
Remove the lower louvred grille (1)
Fig. 66:
Remove the infill panel
RITTAL cooling unit assembly and operating instructions
37
7 Inspection and maintenance
EN
Fig. 67:
Disconnect the display cable
Fig. 71:
Remove the external circuit fan
Fig. 68:
Push back the display cable and press it through
the cable gland (1)
Fig. 72:
Disconnect the fan connectors (1)
Fig. 69:
Push back the display cable and press it through
the cable gland (2)
Fig. 73:
Disconnect the fan connectors (2)
Fig. 70:
Loosen the four screws of the external circuit fan
Fig. 74:
Disconnect the fan connectors (3)
38
RITTAL cooling unit assembly and operating instructions
7 Inspection and maintenance
EN
Fig. 75:
Disconnect the fan earthing cable (1)
Fig. 76:
Disconnect the fan earthing cable (2)
Fig. 78:
Remove the cover
Fig. 77:
Loosen the four screws of the cover
Fig. 79:
Disconnect the earthing cable (1)
RITTAL cooling unit assembly and operating instructions
39
7 Inspection and maintenance
EN
Fig. 80:
Disconnect the earthing cable (2)
Fig. 82:
Clean out the heat exchanger coil and compressor
chamber using compressed air (2)
Fig. 81:
Clean out the heat exchanger coil and compressor
chamber using compressed air (1)
Fig. 83:
Clean out the heat exchanger coil and compressor
chamber using compressed air (3)
40
RITTAL cooling unit assembly and operating instructions
8 Storage and disposal
8
Storage and disposal
9
Technical specifications
EN
Caution! Risk of damage!
The cooling unit must not be subjected
to temperatures above +70°C during
storage.
During storage, the cooling unit must stand upright.
The closed cooling circuit contains refrigerant and oil
which must be properly disposed of for the sake of
the environment. Disposal can be performed at the
RITTAL plant.
Please contact us for advice.
Fig. 84:
Rating plate (technical specifications)
– Observe the mains connection data (voltage and
frequency) as per the rating plate.
– Observe the pre-fuse as per the specifications on
the rating plate.
RITTAL cooling unit assembly and operating instructions
41
9 Technical specifications
EN
Unit
Model No. SK
Basic controller,
RAL 7035
–
3302.100
3302.110
3302.300
3302.310
3303.100
3303.110
3304.100
3304.110
3304.700
Comfort controller,
RAL 7035
–
–
–
–
–
3303.500
3303.510
3304.500
3304.510
3304.800
Basic controller,
stainless steel cover
–
3302.200
3302.210
–
–
3303.200
3303.210
3304.200
3304.210
–
Comfort controller,
stainless steel cover
–
–
–
–
–
3303.600
3303.610
3304.600
3304.610
–
Rated voltage
V
Hz
230, 1~,
50/60
115, 1~,
60
230, 1~,
50/60
115, 1~,
60
230, 1~,
50/60
115, 1~,
60
230, 1~,
50/60
115, 1~,
50/60
230, 1~,
50
Rated current
A
1.6/1.7
3.3
1.6/1.7
4.0
2.6/2.6
5.7
5.4/5.0
10.6/11.1
3.0
Start-up current
A
3.0/3.4
8.0
4.3/5.3
12.0
5.1/6.4
11.5
12.0/14.0
26.0/28.0
12.0
Pre-fuse T
A
10.0
10.0
10.0
10.0
10.0
10.0
10.0
11.0 – 16.0 10.0
Motor circuit-breaker
–
–
–
–
–
–
–
–
–
–
Transformer circuit-breaker
–
–
–
–
–
–
–
–
–
–
–
Useful cooling output Qk
to DIN 3168
L 35 L 35
L 35 L 50
W
W
300/320
150/170
300
150
300/320
150/160
300
150
500/610
280/350
500
280
1000/1060 1000/1060 1000
790/840
790/840
900
Power consumption Pel
to DIN 3168
L 35 L 35
L 35 L 50
W
W
245/255
255/275
290
340
285/300
320/340
290
340
360/380
420/390
470
500
825/775
875/835
850/800
900/875
520
580
1.2
1.2
1.1
1.1
1.4
1.4
1.2
1.2
1.9
R134a
95
R134a
170
R134a
170
R134a
325
R134a
325
R134a
500
25
28
28
25
25
Miniature circuit-breaker/fuse
.
.
Refrigeration factor ε = Qk/Pel
Refrigerant
– Type
– Filling
–
g
R134a
100
Admissible pressure
bar
25
Temperature setting range1)
°C
+20 to +55
Noise level
Protection category to EN 60 529
– Internal circuit
– External circuit
dB (A) < 61
–
–
25
25
< 61
< 61
< 61
< 61
< 61
< 61
mm
280 x 550 x 140
525 x 340 x 153
280 x 550 x
200
400 x 950 x 260
Weight
kg
13
13
17
17
42
< 64
< 64
44
40
IP 54
IP 34
Dimensions (W x H x D)
1) Basic
28
+20 to +45
13
17
39
controller +30°C to +55°C
RITTAL cooling unit assembly and operating instructions
9 Technical specifications
Unit
Basic controller,
RAL 7035
Model No. SK
–
3304.140
3304.142
3305.100
Comfort controller,
RAL 7035
–
3304.540
3304.542
Basic controller,
stainless steel cover
–
Comfort controller,
stainless steel cover
–
Rated voltage
V, Hz
Rated current
A
3305.110
3305.140
3305.142
3328.100
3328.110
3328.140
3329.100
3328.700
3305.500
3305.510
3305.540
3305.542
3328.500
3328.510
3328.540
3329.500
3328.800
3304.240
3305.200
3305.210
3305.240
3328.200
3328.210
3328.240
3329.200
–
3304.640
3305.600
3305.610
3350.640
3328.600
3328.610
3328.640
3329.600
–
400, 3~, 50/ 230, 1~,
460, 3~, 60 50/60
115, 1~,
50/60
400, 3~, 50/ 230, 1~,
460, 3~, 60 50/60
115, 1~,
50/60
400, 3~, 50/ 230, 1~,
460, 3~, 60 50/60
230, 1~,
50
2.8/2.9
12.1/13.6
2.6/2.9
14.7/17.3
2.8/3.3
4.5
12.2/11.3
22.0/26.0
36.0/39.0
6.8/7.8
16.0
18.0 – 25.0 6.3 – 10.0
6.0/6.5
7.5/9.1
8.6/10.6
Start-up current
A
11.5/12.7
22.0/24.0
42.0/46.0
Pre-fuse T
A
6.3 – 10.0
16.0
14.0 – 20.0 6.3 – 10.0
Motor circuit-breaker
–
–
–
–
–
Transformer circuit-breaker
–
–
–
–
–
Miniature circuit-breaker/fuse
–
–
–
–
–
Useful cooling
.
output Qk
to DIN 3168
L 35 L 35
L 35 L 50
W
W
1000/1060 1500/1510 1500/1510 1500/1510 2000/2350 2000/2350 2000/2350 2500/2750 2000
790/840
1230/1250 1230/1250 1230/1250 1450/1690 1450/1690 1450/1690 1600/1750 1630
Power
consumption Pel
to DIN 3168
L 35 L 35
L 35 L 50
W
W
700/675
785/800
975/1125 1000/1175 925/1100 1025/1200 1085/1250 1050/1275 1450/1675 780
1125/1285 1165/1325 1085/1275 1250/1350 1300/1410 1275/1525 1625/2000 870
1.4
1.5
1.5
1.6
2.0
1.8
1.9
1.7
2.6
R134a
500
R134a
600
R134a
600
R134a
600
R134a
950
R134a
950
R134a
950
R134a
950
R134a
750
25
25
25
28
28
28
28
.
Refrigeration factor ε = Qk/Pel
Refrigerant
– Type
– Filling
–
g
Admissible pressure
bar
25
Temperature setting range1)
°C
+20 to +55
Noise level
dB (A) < 64
Protection category
to EN 60 529
– Internal circuit
– External circuit
–
–
12.0
10.0
–
–
–
–
–
–
28
+20 to +45
< 64
< 64
< 64
< 64
46
42
66
< 64
< 64
< 64
< 64
67
69
66
IP 54
IP 34
Dimensions (W x H x D)
mm
400 x 950 x 260
Weight
kg
40
1) Basic
21.0/21.0
16.0
41
400 x 1580 x 290
73
controller +30°C to +55°C
RITTAL cooling unit assembly and operating instructions
43
EN
9 Technical specifications
Model No. SK
Unit
EN
Basic controller, RAL 7035
–
3329.110
3329.140
3332.140
3361.100
3361.110
3361.140
Comfort controller, RAL 7035
–
3329.510
3329.540
3332.540
3361.500
3361.510
3361.540
Basic controller,
stainless steel cover
–
3329.210
3329.240
3332.240
3361.200
3361.210
3361.240
Comfort controller,
stainless steel cover
–
3329.610
3329.640
3332.640
3361.600
3361.610
3361.640
Rated voltage
V, Hz
115, 1~,
50/60
400, 3~, 50/
460, 3~, 60
400, 3~, 50/
460, 3~, 60
230, 1~,
50/60
115, 1~,
60
400, 2~,
50/60
Rated current
A
17.0/22.0
3.7/3.8
4.2/4.2
2.3/2.4
5.3
1.2/1.4
Start-up current
A
44.0/42.0
6.8/7.6
9.2/11.0
5.6/5.6
12.0
3.1/3.3
Pre-fuse T
A
18.0 – 25.0
6.3 – 10.0
6.3 – 10.0
10.0
10.0
6.3 – 10.0
Motor circuit-breaker
–
–
–
–
–
Transformer circuit-breaker
–
–
–
–
–
–
–
–
–
–
Useful cooling output Qk
to DIN 3168
L 35 L 35
L 35 L 50
W
W
2500/2750
1600/1750
2500/2700
1900/1950
4000/4400
3070/3570
750/780
510/540
750
500
750/780
510/540
Power consumption Pel
to DIN 3168
L 35 L 35
L 35 L 50
W
W
1500/1725
1675/2065
1425/1625
1675/1975
1850/2250
2120/2590
480/550
530/640
570
670
480/550
530/640
1.7
1.8
2.1
1.5
1.5
1.5
R134a
950
R134a
950
R134a
3000
R134a
280
R134a
260
R134a
280
28
28
28
Miniature circuit-breaker/fuse
.
.
Refrigeration factor ε = Qk/Pel
Refrigerant
– Type
– Filling
–
g
Admissible pressure
bar
28
Temperature setting range1)
°C
+20 to +55
Noise level
Protection category to EN 60 529
– Internal circuit
– External circuit
dB (A)
< 64
–
–
IP 54
IP 34
< 64
< 64
< 64
Dimensions (W x H x D)
mm
400 x 1580 x 290
500 x 1580 x 340 280 x 550 x 280
Weight
kg
76
70
91
22
28
28
+20 to +52
+20 to +55
< 64
< 64
22
22
Model No. SK
Unit
Basic controller, RAL 7035
–
3366.100
3366.110
3366.140
3377.100
3377.110
3377.140
Comfort controller, RAL 7035
–
3366.500
3366.510
3366.540
3377.500
3377.510
3377.540
Basic controller,
stainless steel cover
–
3366.200
3366.210
3366.240
3377.200
3377.210
3377.240
Comfort controller,
stainless steel cover
–
3366.600
3366.610
3366.640
3377.600
3377.610
3377.640
Rated voltage
V, Hz
230, 1~,
50/60
115, 1~,
50/60
400, 3~, 50/
460, 3~, 60
230, 1~,
50/60
115, 1~,
50/60
400, 3~, 50/
460, 3~, 60
Rated current
A
7.1/7.3
14.3/14.7
3.0/3.1
7.1/7.3
14.3/14.7
3.3/3.4
Start-up current
A
22.0/24.0
43.0/47.0
8.0/8.8
22.0/24.0
43.0/47.0
8.0/8.8
Pre-fuse T
A
10.0
14.0 – 20.0
6.3 – 10.0
10.0
14.0 – 20.0
6.3 – 10.0
Motor circuit-breaker
–
–
–
–
–
Transformer circuit-breaker
–
–
–
–
–
Miniature circuit-breaker/fuse
–
–
–
–
–
.
Useful cooling output Qk
to DIN 3168
L 35 L 35
L 35 L 50
W
W
1500/1500
1050/1100
1500/1500
1050/1100
1500/1500
980/1080
1500/1500
1050/1100
1500/1500
1050/1100
1500/1500
980/1080
Power consumption Pel
to DIN 3168
L 35 L 35
L 35 L 50
W
W
1045/1175
1220/1335
1075/1200
1265/1375
1090/1240
1260/1430
1045/1175
1220/1335
1075/1200
1265/1375
1090/1240
1260/1430
1.4
1.4
1.3
1.4
1.4
1.3
R134a
700
R134a
700
R134a
700
R134a
700
R134a
700
R134a
700
28
28
28
28
28
< 64
< 64
< 64
< 64
< 64
46
45
.
Refrigeration factor ε = Qk/Pel
Refrigerant
– Type
– Filling
–
g
Admissible pressure
bar
28
Temperature setting range1)
°C
+20 to +55
Noise level
Protection category to EN 60 529
– Internal circuit
– External circuit
dB (A)
< 64
–
–
IP 54
IP 34
Dimensions (W x H x D)
mm
450 x 1590 x 195
Weight
kg
45
1) Basic
44
50
450 x 1590 x 165
50
46
controller +30°C to +55°C
RITTAL cooling unit assembly and operating instructions
10 List of spare parts
10 List of spare parts
EN
75
SK 3302.xxx
40
10
71
25
45
1
100
55
71
90
15
5
Fig. 85:
Spare parts for SK 3302.xxx
SK 3302.3xx
10
90
71 20
71
25
100
45
40
1
5
15
55
Fig. 86:
Spare parts for SK 3302.3xx
RITTAL cooling unit assembly and operating instructions
45
10 List of spare parts
EN
SK 3303.xxx
SK 3361.xxx
10
40
71
30
75
25
1
45
15
55
100
90
5
71
71
20
71
Fig. 87:
Spare parts for SK 3303.xxx, SK 3361.xxx
SK 3304.xxx
SK 3305.xxx
10
40
71
30
102
75
1
45
25
100
71
50
80
15
20
55
90
45
5
71
71
101
Fig. 88:
46
Spare parts for SK 3304.xxx, SK 3305.xxx
RITTAL cooling unit assembly and operating instructions
10 List of spare parts
75
SK 3328.xxx
SK 3329.xxx
EN
10
40
46
71
30
102
45
71
20
50
1
55
100
45
46
90
80
5
71
71
15
101
Fig. 89:
Spare parts for SK 3328.xxx, SK 3329.xxx
75
SK 3332.xxx
10
46
40
71
102
45
25
100
50
55
1
45
71
90
46
71
71
20
15
5
30
101
Fig. 90:
Spare parts for SK 3332.xxx
RITTAL cooling unit assembly and operating instructions
47
10 List of spare parts
EN
SK 3366.xxx
SK 3377.xxx
75
75
100
40
46
10
71
102
45
20
90
50
30
71
55
1
25
45
101
46
5
80
15
Fig. 91:
Spare parts for SK 3366.xxx, SK 3377.xxx
Legend
1
Compressor
5
Condenser fan
10 Evaporator fan
15 Dispatch bag
20 Expansion valve
25 Filter dryer
30 PSAH pressure-operated switch
40 Controller board
45 Louvred grille 1
46 Louvred grille 2
50 Infill panel
55 Display
71 Temperature sensor
75 Enclosure tray
80 Transformer
90 Evaporator coil
100 Condenser
101 Condensate evaporator
102 Miniature fuse, condensate evaporator
(T4A; 6.3 x 32 mm)
48
Note:
As well as the spare part number, when
ordering spare parts the following information must be provided:
– Unit model
– Fabrication number
– Date of manufacture
This information may be found
on the rating plate.
RITTAL cooling unit assembly and operating instructions
11 Appendix: Cut-out and hole sizes
11 Appendix:
Cut-out and hole sizes
353
11.1 Dimensions for external mounting
EN
55
345
240
78.5
354
326
251
360
280
140
85.5
Fig. 95:
49
Ø8
155
(10x)
260
354
165.5
550
501
353
360
354
354
SK 3366.xxx, SK 3377.xxx external mounting
250
350
260
280
34.5
SK 3302.xxx external mounting
(except SK 3302.3xx)
255
400
Fig. 92:
525
6
385
350
281
340
950
Ø 9.5 (8x)
255
153
471
25
15
350
Fig. 96:
Fig. 93:
SK 3304.xxx, SK 3305.xxx external mounting
SK 3302.3xx external mounting
35
400
280
290
262
350
380
200
310
15.5
280
1580
550
532
480
550
266
Ø 13 (10x)
25
275
SK 3303.xxx, SK 3361.xxx external mounting
340
Fig. 94:
320
325
260
Ø 8 (4x)
Fig. 97:
RITTAL cooling unit assembly and operating instructions
SK 3328.xxx, SK 3329.xxx external mounting
49
11 Appendix: Cut-out and hole sizes
400
500
370
340
380
145
440
380
320
145
R9.5 (2x)
1580
500
330
45
EN
1580
1540
1558
1554
25
Fig. 98:
376
275
375
440
360
164
Ø 13 (10x)
Ø 13 (4x)
SK 3332.xxx external mounting
R9.5 (2x)
11.2 Dimensions for partial internal
mounting
320
Fig. 101: SK 3328.xxx, SK 3329.xxx partial internal mounting
280
100
20
254
100
500
25
145
195
550
497
266
523
524
362
18 x 45°
1580
474
1530
1550
Ø 8 (4x)
(230)
Fig. 99:
SK 3303.xxx, SK 3361.xxx partial internal mounting
Ø 13 (4x)
400
370
105
330
155
Fig. 102: SK 3332.xxx partial internal mounting
380
920
920
950
25 x 45
Ø 9.5 (4x)
Fig. 100: SK 3304.xxx, SK 3305.xxx partial internal mounting
50
RITTAL cooling unit assembly and operating instructions
11 Appendix: Cut-out and hole sizes
11.3 Dimensions for full internal mounting
98
280
210
370
25
R6 (4x)
25
200
EN
400
42
254
25 x 45
2
50
920
950
920
550
266
518
492
524
Ø 15 (2x)
380
Ø 8 (4x)
18 x 45°
Ø 9.5 (4x)
(230)
Fig. 103: SK 3302.1xx full internal mounting
98
55
Fig. 106: SK 3304.xxx, SK 3305.xxx full internal mounting
525
400
20
510
370
240
50
R9.5 (2x)
325
20 x 45°
314
340
320
Ø 7.5 (4x)
Fig. 104: SK 3302.3xx full internal mounting
376
1580
1540
1558
1554
499
42
280
158
25
254
200
Ø 13 (4x)
R9.5 (2x)
Ø 19 (2x)
550
518
492
524
320
266
Fig. 107:
SK 3328.xxx, SK 3329.xxx full internal mounting
45
Ø 8 (4x)
400
18 x 45°
(230)
1500
45
1510
Fig. 105: SK 3303.xxx, SK 3361.xxx full internal mounting
Fig. 108:
RITTAL cooling unit assembly and operating instructions
SK 3366.xxx, SK 3377.xxx full internal mounting
51
Schaltschrank-Systeme
Industrial Enclosures
Coffrets et armoires électriques
Kastsystemen
Apparatskåpssystem
Armadi per quadri di comando
Sistemas de armarios
Stromverteilung
Power Distribution
Distribution de courant
Stroomverdeling
Strömfördelning
Distribuzione di corrente
Distribución de corriente
Elektronik-Aufbau-Systeme
Electronic Packaging
Electronique
Electronic Packaging Systems
Electronic Packaging
Contenitori per elettronica
Sistemas para la electrónica
System-Klimatisierung
System Climate Control
Climatisation
Systeemklimatisering
Systemklimatisering
Soluzioni di climatizzazione
Climatización de sistemas
IT-Solutions
IT Solutions
Solutions IT
IT-Solutions
IT-lösningar
Soluzioni per IT
Soluciones TI
318 635
Communication Systems
Communication Systems
Armoires outdoor
Outdoor-behuizingen
Communication Systems
Soluzioni outdoor
Sistemas de comunicación
Switch to perfection
R
3rd
edition
12/09
(04/07)
Rittal GmbH & Co. KG · Postfach 1662 · D-35726 Herborn
Telephone: +49(0)2772 505-0 · Telefax: +49(0)2772 505-2319 · eMail: info@rittal.de · www.rittal.com