WL-12-A 46-755X & 46-756 16” WOOD LATHE PART NO.

Add to my manuals
2 Pages

advertisement

WL-12-A 46-755X & 46-756 16” WOOD LATHE PART NO. | Manualzz

46-755X & 46-756

16” WOOD LATHE

WL-12-A

PART NO.

A02991

DATE 04-13-04

SPEED CONTROL

WHITE

BLACK

GREEN

SWITCH GREEN

WHITE

BLACK

L1 L2 T1

B2 B1

T2 T3

GREEN

WHITE

BLUE

RED

RESISTOR

WIRING DIAGRAM

MOTOR

Page1/ WL-12/DEB

REPLACEMENT PARTS

Ref.

No.

Part No.

Description

14

15

16

17

10

11

12

13

8

9

6

7

2

3

**

4

422-39-138-0007 KNOB

1340946

1340945

901791

911331

DRIVE CENTER, INCL.:

CENTER POINT

KNOCKOUT BAR

12 TOOL REST "

434-10-020-0001 CAP

434-10-042-0004 HEADSTOCK ECCENTRIC

A03028 HEADSTOCK

434-10-071-0004 INDEX PIN

46-947 FACE PLATE

434-10-085-0001 SPINDLE

434-10-626-0001 BALL BEARING

434-10-626-0002 BALL BEARING

22

24

25

26

18

19

20

21

909214 HANDW HEEL, INCL.: REF. 20

434-10-101-0001 1 3/4 W RENCH

A03027 MOTOR YOKE

434-10-112-0002 3/8-16 DUAL END SCREW

A03186 DRIVEN PULLEY , INCL.: REF. 20

901-04-150-0231 5/16-18 X 3/8 SET SCREW

A03187

A02396

MOTOR PULLEY, INCL.: REF. 20

BELT

A03189 TOOL REST BASE, INCL.:

434-10-111-0002 SCREW

27

434-10-105-0001 SLEEVE

A04138

60

61

63

64

65

66

67

43

46

48

49

36

39

41

42

31

32

33

34

28

29

30

909935

LEVER, 46-755X

LEVER, 46-756

434-10-019-0003 CAM SHAFT, 46-755X

434-10-019-0001 CAM SHAFT, 46-756

A02994 5/16-18 X 1/2 SET SCREW

928-01-023-1644 SPRING

434-10-027-0001 ONE HOLE CLAMP

901-03-043-1840 5/16-18 X 11/2 SCREW

434-03-112-0002 3/8-16 EYE BOLT

902-01-213-1838 3/8-16 NUT

434-10-306-0004 BED

A03030 COVER

COVER A03031

908864

A02942

SW ITCH COVER

LEG

434-10-027-0002 CLAMP

434-10-042-0001 TAILSTOCK ECCENTRIC

434-10-406-0001 TAIL SHAFT

A03506 SCREW

434-10-400-0001 HANDW HEEL

50

51

52

53

55

56

902-01-021-7801 9/16-12 HEX NUT

904-07-010-5566 W ASHER

905-01-010-5072

907-00-000-2486

57 A04167

SPRING PIN

COVER

A02987

LEVER , 46-755X

LEVER , 46-756

434-10-111-0001 3/8-16 U-BOLT

901-03-043-1841 3/8-16 X 2 1/2 SCREW

904-01-010-1615 W ASHER

902-01-040-1026 3/8-16 NUT

434-10-132-0002 SCALE

A03190

A02994

TAILSTOCK, INCL.:

5/16-18 X 1/2 SET SCREW

**

**

**

**

**

**

**

**

116

120

121

122

123

124

125

106

107

108

110

111

112

113

115

90

91

92

93

95

98

101

105

72

73

74

81

83

84

85

89

76

77

79

80

Ref.

No.

Part No.

Description

901-01-060-0640 3/8-16 X 3/4 SCREW

901-03-040-8015 1/4-20 X 1/2 SCREW

902-01-133-1529 1/4-20 NUT

904-02-020-1704 W ASHER

A03509 W ARNING LABEL

438-01-004-0007 CORD CLAMP

422-39-067-0001 PADDLE

438-01-011-0051 INSULATOR

911703 VARIABLE FREQUENCY DRIVE

438-01-017-0206 SW ITCH

438-01-302-0403 CORD

A02458 MOTOR 2HP 230 V 3 PH

1342071

1340945

LIVE CENTER, INCL.:

CENTER POINT

901-02-443-1812 8-32 X 1/2 SCREW

901-03-010-0776 3/8-16 X 7/8 SCREW

901-03-030-8007 3/8-16 X 3/4 SCREW

901-05-183-1142 10-32 X 5/8 SCREW

902-01-073-1817 1.25-8 HEX NUT

904-15-102-0196 RETAINING RING, NOTE A

905-01-012-0310 SPRING PIN

927-03-010-2695 3/16 x 1 KEY

928-06-021-3393 LOAD SPRING

955-03-023-1739 "T" HEX W RENCH

803228 8-32 X1 SCREW

434-10-072-0009 END CAP

901-03-010-3345 1/4-20 X 1 SCREW

434-10-137-0005 LABEL, 46-755X

434-10-137-0004 LABEL, 46-756

A02981 HARDW ARE PACK

902-01-010-5900 3/8-16 NUT

A02929 FOOT

901-11-020-0823 3/8-16 X 1 1/2 BOLT

902-01-020-1227 1/2-20 NUT

A03595 RESISTOR

438-01-004-0085 CORD CLAMP

*

**

ACCESSORIES: (Optional)

46-739

46-946

25-857

46-408

46-552

50-341

46-933

46-490

FACE SHIELD

8" FACE PLATE

LAMP ATTACHMENT

TURNING DUPLICATOR

SPINDLE ADAPTOR (NOTE E)

1 1/4 X 8 THREAD TO 1 X 8 THREAD

MOBILITY KIT

DRIVE CENTER

BALL BEARING CENTER

NOT SHOW N ASSEMBLED

NOT SHOW N

SERVICE NOTE

A: Ref. 105 must be installed with flat side facing race of bearing Ref. 14

E: 46-552 adapter has 1 X 8 external thread so that chucks with this thread can be used on this lathe.

______________________________________________________________

STANDARD SAFETY EQUIPMENT

In order to promote tool safety, Delta Machinery strictly enforces the policy of repairing or replacing any damaged or missing standard safety equipment on machines presented to Delta Authorized Service Centers for service/repairs. Any product that is presented to a Delta Authorized Service Centers for repairs which contains missing or damaged standard safety equipment will have that equipment repaired or replaced and the customer will be charged for any such service/repairs. Customers can avoid such charges only if the missing safety component is supplied to the service center at the time of repair.

This parts list is provided to aid in obtaining service parts. Copies of the instruction and maintenance literature can be obtained through the

Delta Technical Publications Department or through your service outlet.

Page 2/ WL-12/DEB

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement