Specification

Model Name

Display Orientation

Display Device

Back Light Tehcnology

Display Resolution

Viewable Image Size

Brightness

Contrast Ratio

Viewing Angle(H/V)

Display Colors

Mullion(Total)

Back Light Operating Life

Optional Input Board Slot

Control Signal Input

Input Signal

Overlay Function

Control S/W(Option)

Power Consumption

Voltage Range

Dimensions

VS-L55HM70U

Landscape/Portrait

TFT LCD(SPVA Mode)

LED(Direct)

Full HD(1920 x 1080 Pixels)

55"(H:1209.6mm/V:680.4mm)

700cd/m

2

(Typ.)@Bright Mode

500cd/m

2

(Typ.)@Normal Mode

350cd/m

2

(Typ.)@Eco Mode

3500:1(Typ.)

178Degree

16.7Million

5.7mm(Typ.)/6.7mm(Typ.) *

50000hrs(Average) x3(One VC-B70DC card is pre-installed)

RS-232C: Dsub9

LAN: RJ45(10BASE-T/100BASE-TX)

Dsub 9 x 2(IN/OUT)

Mitsubishi Original Control Link

Wired Remote: F3.5 Jack

IR Receiver(Option)

Refer to the bottom input board(Option) specifications

Max. 6 Windows per each screen (with VC-B70V2)

Max. 3 Windows per each screen (with other boards)

Mitsubishi D-Wall Software Suite

210W(Typ.)@Bright Mode

170W(Typ.)@Normal Mode

150W(Typ.)@Eco Mode

AC100-240V±10%,50/60Hz±1Hz

1215.3mm(W) x 686.1mm(H) x 173mm(D)

47.8inch(W) x 27inch(H) x 6.8inch(D)

Operating Condition

5-35C.Degree(41-95F.Degree)@Normal/Eco Mode

5-30C.Degree(41-86F.Degree)@Bright Mode

Weight 40Kg/88lbs

*When using with Wall Mount Frame BR-HM70KK(option).

99

173

3.8

1209.6 (Active Area)

1215.3

1.9

150

700

300 150 8-M6 Depth 10

150 300 150

Analog RGB input board(Option)

Model number

Signal input terminal(Analog RGB)

RGB input scanning frequency

Signal resolutions

Horizontal

Vertical

Pixel clock rate

Functions

VC-B70G2

5BNC x1, HD D-sub 15 pins x1

VGA(640 x 480) - WUXGA(1920 x 1200)

31.5kHz - 92kHz

49Hz - 85Hz

25MHz - 162MHz

Image scaling(shrink and zoom)

Frame rate conversion

Digital RGB input board(Option)

Model number

Signal input terminal(Digital RGB)

RGB input scanning frequency

Signal resolutions

Horizontal

Vertical

Pixel clock rate

Sigal format

Functions

VC-B70D2

DVI-D x2

VGA(640 x 480) - WUXGA(1920 x 1200)

31.5kHz - 92kHz

49Hz - 85Hz

25MHz - 162MHz

TMDS

Image scaling(shrink and zoom)

Frame rate conversion

Video input board(Option)

Model number

Signal input terminal(Analog Video)

Analog video input signals

Functions

VC-B70V2

3BNC x2

NTSC, NTSC4.43, PAL, PAL-M, PAL-N

PAL-60, SECAM

Image scaling(shrink and zoom)

Frame rate conversion

Daisy chain board(Option)

Model number

Signal input terminal

Signal output terminal

RGB input scanning frequency

Signal resolutions

Horizontal

Vertical

Analog video input signals

Pixel clock rate

Functions

VC-B70DC

Analog RGB: HD D-sub15pins x1

Digital RGB: DVI-D x1

Analog video: 3BNC x1

Digital RGB: DVI-D x 1(for daisy chain use only)

VGA(640 x 480) - WUXGA(1920 x 1200)

31.5kHz - 92kHz

49Hz - 85Hz

NTSC, NTSC4.43, PAL, PAL-M, PAL-N

PAL-60, SECAM

25MHz - 162MHz

Image scaling(shrink and zoom)

Frame rate conversion

Daisy chain(Up to 16 cubes)

3G-SDI input board(Option)

Model number

Signal input terminal

Input signals

Signal output terminal

Gen Lock input termninal

Functions

VC-B70SD1

HD-SDI: BNC x1

3G-SDI (SMPTE424M): 1080p@50/59.94/60Hz

HD-SDI (SMPTE292M): 1080i@50/59.94/60Hz,

720p@50/59.94/60Hz

SD-SDI (SMPTE259-C): [email protected],576@50Hz

HD-SDI: BNC x1(for through output)

BNC x1

Image scaling(shrink and zoom)

Frame rate conversion through output

*At least one input board per single display is needed for operation.

*The specifications are subject to change without notices.

Display Wall

VS-L55HM70U

55" LCD Display Wall

辦 事 處：香港北角電氣道169號7樓

維修服務：葵涌打磚坪街26-38號成功中心24樓

網址：www.mitsubishi-ryoden.com.hk

電話：852 2510 1505

電話：852 2427 8484

Specifications are subject to change without notice.

M i t s u b i s h i E l e c t r i c

L C D D i s p l a y Wa l l S y s t e m S o l u t i o n s

The Mitsubishi Electric LCD Display Wall System is the ideal solution for small-and medium-sized control rooms that require high picture quality from displays used continuously for long periods of time.

It features an advanced technology system that provides intelligence, durability, redundancy and space savings.

We have extensive expertise in this field, including the installation of over 50,000 display wall cubes for mission-critical applications.

Combining a space-saving design and easy video/data integration using slot-in board processing, this display wall system is perfect for the following applications:

>Traffic management

>Security operations

>Power distribution/

Water treatment management

>Broadcasting

5.7mm mullion (total)

Super narrow 5.7mm mullion (total) minimizes the image content loss, which is critical for command and control room usage.

Front access for easy service

Key Feature

When used in combination with Mitsubishi Electric’s original optional wall mount kit, LCD panels can be accessed from the front-side of the system. This design makes it possible for panels to be serviced from the front as well as the rear.

5.7mm

Wall

High picture quality over the entire wall

Digital gradation circuit

Key Feature

Mitsubishi Electric's innovative digital gradation circuit provides uniform brightness distribution across the screen, resulting in the reproduction of sharp, vivid images form edge to edge on multi-screen configurations.

This virtually eliminates the problem of decreased brightness at the edges of each screen.

Without “Digital Gradation Circuit” With “Digital Gradation Circuit”

Color space control

Our LCD displays are equipped with an innovative digital color space control circuit developed in-house. The circuit works to balance and blend colors, compensating for the color and brightness discrepancies among LCD displays.

Internal processing

Built-in processor

Key Feature

Each display of LCD Display Wall System is equipped with an internal data-processing function that allows to show up to six windows (with

VC-B70V2) or three windows (with other boards) per a single panel, and allows to show up to three windows placed any size and position across the entire wall when using the daisy chain function of the daisy chain board.

Install Mitsubishi Electric's D-Wall software suite and the entire imaging system can be controlled intuitively from a user-friendly graphical user interface.

Without overlay function With overlay function

Black strips are displayed on both sides when the image source is set to the 4:3 aspect ratio.

Only one screen can be displayed at a time.

Freely choose the size and position of the image windows.

Without “Color Space Controll” With “Color Space Controll”

Dynamic brightness balancing

With a built-in brightness sensor, Dynamic brightness balancing circuit can keep the brightness uniformity of display wall over the period of operation time by communicating the measured brightness data by every 2 seconds.

Example 2x2 display wall

100%

Brightness

50%

As the black line indicates, the brightness level of the 2x2 display wall is maintained at the same brightness

Time

Bezel compensation

Key Feature

Images can be displayed in two modes, Real Picture Window (RPW) or

Natural Picture Window (NPW).

RPW displays images using the entire input signal (no image loss), making it suitable for displaying surveillance images and similar applications.

NPW realizes a smoothly connected screen image appearance when using multiple screens; perfect for moving pictures.

Image portions corresponding to the bezel width are not hidden

(no image loss).

Image portions corresponding to the bezel width are hidden, realizing a naturally connected image.

RPW NPW

3 operational modes

Key Feature

Three backlight power modes (Bright, Normal and Eco) can be selected according to the operating environment.

Normal mode Bright mode Eco mode

Redundancy

Smart Switch

Key Feature

The LCD Display Wall System is also equipped with a “Smart Switch".

This signal source control function provides the redundancy necessary for mission-critical applications that require continuous operation. If the signal is unexpectedly lost, the signal source is automatically switched to an alternative device (either "port-to-port" or "board-toboard") within seconds of detecting the 'no signal' status. As a result, user downtime is minimized in the event of a signal source failure.

User-friendly graphical user interface

(Option)

“D-Wall”, a software suite developed by Mitsubishi Electric, is available for LCD Wall System. The software was originally created for use with the display wall cube and processor, and has been continuously modified and upgraded.

In addition to basic functions such as wall configuration support, display layout control, and brightness and color control, the following functions for control room use have been incorporated into the latest version.

Remote multi-mouse cursor application control

When being operated under a client-server configuration, multiple users (clients) can simultaneously navigate applications using their dedicated mouse. Individual cursors, colorcoded for each mouse, are shown on the display wall, and all clients can control applications on the server. This function simultaneously enables more efficient control room operation and room layout flexibility.

Alert message utility

This information function displays alerts and notices on the wall, supporting teamwork in the control room.

System monitoring

This management function constantly monitors key operating parameters of the LCD Wall System such as the status of cooling fans and temperature inside the displays. The information for each display us displayed via the GUI.

Multilingual interface

The D-wall software suite is available in multiple languages.