Emerson CF2455PW00 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
ODYSSEY®
54” Ceiling Fan
Owner's Manual
Model No.
CF2455BS00
CF2455ORB00
CF2455PW00
Net Weight:
Part No. F40BP73370000
26.0 Lbs.
Form No. BP7337
U.L. Model No.: CF2455
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and
Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling
fan must be grounded as a precaution against possible electrical shock. Electrical installation
should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted an capable of reliably supporting a least 50
pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan proves the minimum recommended floor-to-fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electrical shock, this fan should only be used with fan
speed control, Model No. SW105, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use this product by Emerson Electric Co. Substitution of
parts or accessories not designated for use with this product by Emerson could result in personal
injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall
control/switch.
DATE CODE:
The date code of this fan may be found on
the box, stamped in ink on a white label.
You should record this data above and keep
it in a safe place for future use.
2
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One six-inch blade screwdriver
One stepladder
One Phillips head screwdriver
One wire stripper
Seven wire connectors (supplied)
Three 40-watt (max.) candelabra base bulbs (uplight)
Three 60-watt (max.) candelabra base bulbs (lower light)
!
MATERIALS
Wire Size A.W.G.
14
12
WARNING
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire
size, to right:
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place
a check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
!
7. Seven wire connectors
8. Three 8-32 x 3/8" phillips head screws
9. One hairpin clip
10. One clevis pin
11. Two knurled knob screws
12. Twenty-one 10-32 x 3/8" pan head screws
13. One jumper assembly
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
1. Open styrofoam unit containing fan. Remove upper
and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:
a. One fan motor and housing assembly
b. One motor coupling cover
c. One ceiling cover
d. Five fan blades
e. Five blade holder caps (left)
f. Five blade holder caps (right)
g. One hanger ball/downrod assembly
h. One hanger bracket
i. One light kit adapter
j. One light kit plate assembly
k. One light kit glass
l. Two die cast light kit glass holders
m.One uplight lead assembly
n. One SW116 Fan/Light Wall Control
(transmitter)
o. One SW105 Receiver
p. One loose parts bag containing:
1. One setscrew
2. One 5/32" hex wrench
3. One 3/16” hex wrench
4. Four 8-32 x 1-1/4” threaded studs
5. Four knurled knobs
6. Four lockwashers
FAN BLADES
CEILING
COVER
MOTOR
COUPLING
COVER
UPLIGHT
LEAD ASSEMBLY
HANGER BALL/
DOWNROD
ASSEMBLY
HANGER
BRACKET
BLADE HOLDER
CAPS (LEFT)
BLADE HOLDER
CAPS (RIGHT)
DIE CAST
GLASS HOLDERS
LOOSE
PARTS
BAG
SW105
RECEIVER
HI
U/L
MED
D/L
LOW
REV
FAN OFF
EMERSON
SW116 FAN/LIGHT
WALL CONTROL
LIGHT KIT
GLASS
LIGHT KIT
PLATE
ASSEMBLY
FAN MOTOR
AND HOUSING
ASSEMBLY
LIGHT KIT
ADAPTER
3
IMPORTANT: Your ceiling fan is supplied with an
SW116 Fan/Light Wall Control (transmitter) and a
remote control SW105 Receiver which mounts
under the ceiling cover. This system allows you to
regulate your ceiling fan speed, airflow direction,
and light intensity. An optional Emerson Electric
SR110 Remote Control may also be used.
Preliminary Procedures
IMPORTANT: Before assembling your ceiling fan,
refer to sections “Setting Operating Frequency of
Wall Control and Receiver” and “Battery
Installation of Wall Control”, page 11. These
sections instruct you how to:
a. Set the operating frequency of the fan/light wall
control and the remote control receiver.
b. Install the fan/light wall control in the wall box.
You will then be ready to proceed with the
assembly and installation of your ceiling fan.
IMPORTANT: Your ceiling fan will not function
properly and may be damaged, if used with any
wall dimmer switch or control other than the
Emerson controls listed above.
Electrical Requirements
Ceiling Fan Assembly
Procedures
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
!
1. Position the fan motor and housing assembly in the
lower styrofoam packing so that the top for the
motor is facing you.
2. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 11.
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
PIN
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time
and remove the existing light fixture.
HANGER BALL
DOWNROD
!
WARNING
Figure 1
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with national and local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
!
SETSCREW
3. Using a wire connector (supplied), connect the
yellow uplight lead (supplied) to the yellow wire
from the motor (Figure 2).
4. Separate, untwist and unkink the three black, white
and blue motor wires and the yellow uplight lead.
Route these wires through the downrod.
5. Fold the wires from the downrod into the slot in the
motor coupling. Then slide the downrod down the
wires and seat the downrod in the motor coupling
(Figure 2).
WARNING
To avoid possible fire or shock, follow all wiring
instructions carefully. Any electrical work not
described in these instructions should be done or
approved by a licensed electrician.
4
6. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 2). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose.
KNURLED KNOB
LOCKWASHER
COUPLING COVER
1-1/4" THREADED
STUD
7/8"
MOTOR
!
WARNING
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
Figure 3
9. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 4).
!
DOWNROD
SETSCREW
CLEVIS PIN
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
HAIRPIN
CLIP
MOTOR
COUPLING
10. Reinstall the hanger ball on the downrod
as follows. Route the motor leads through the
hanger ball and slide the hanger ball over the
downrod (Figure 4). Install the pin through the
holes at the top of the downrod and slide the
hanger ball up the downrod, aligning the ball so the
pin is captured in the groove in the top of the
hanger ball. Pull the hanger ball up tight against the
pin and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
DOWNROD
SETSCREW
HAIRPIN
CLIP
CLEVIS
PIN
WARNING
CONNECT YELLOW WIRES
USING WIRE CONNECTOR
CLEVIS
PIN
MOTOR COUPLING
PIN
HANGER BALL
CEILING COVER
DOWNROD
SETSCREW
Figure 2
7. Install the setscrew (supplied) in the motor coupling
and tighten using the 5/32” setscrew wrench
(supplied) (Figure 2).
8. Screw two 1-1/4” threaded studs (supplied) into the
motor (Figure 3). Leave approximately 7/8” of the
stud extending above the motor. Coil the wires and
wire connectors around the motor coupling, then
slide the coupling cover over the downrod and
rotate the cover until the threaded studs protrude.
Install two lockwashers (supplied) and knurled
knobs (supplied) to secure the cover to the motor.
All wires and wire connectors must be enclosed
under the coupling cover.
NOTE: Lightly snug the knurled knobs and make
sure the wires and wire connectors are completely
inside the coupling cover and not pinched between
the coupling cover and the motor.
Figure 4
11. The blue, black, white, and yellow leads exiting
the downrod are 80-inches long. Before installing
the fan, measure up approximately 6 to 9-inches
above the ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end
of leads.
5
12. Position the center styrofoam section on the
upper section, and then position the fan motor
and housing on the center section so that the
bottom of the motor is facing you (Figure 5). The
styrofoam sections will hold the assembly while
you perform the following steps.
LIGHT KIT PLATE
ASSEMBLY
BLUE WIRE
FAN MOTOR AND
HOUSING ASSEMBLY
CENTER
STYROFOAM
SECTION
WHITE
WIRES
JUMPER ASSEMBLY
UPPER
STYROFOAM
SECTION
Figure 5
BLACK WIRE
13. Using the 3/16” setscrew wrench (supplied),
loosen the setscrew in the collar of the light kit
adapter assembly (Figure 6).
14. Pass the connectors and wires from the motor
shaft through the light kit adapter collar (Figure 7)
in the following sequence:
LIGHT KIT
ADAPTER
Figure 7
a. First, pass the four-pin connector through the
collar;
18. Secure the light kit plate assembly to the light kit
adapter by threading three 8-32 x 3/8” phillips
head screws (supplied) into the threaded holes in
the adapter assembly. (Figure 8).
b. Next, pass the single-pin connector through the
collar;
NOTE: Do not pinch wires between the light kit
plate assembly and the adapter assembly.
c. Then pass the white and blue wires through the
collar.
8-32 x 3/8" PHILLIPS
HEAD SCREW (3)
LIGHT KIT ADAPTER
LIGHT KIT
PLATE ASSEMBLY
15. Screw the light kit adapter tightly onto the motor
shaft (Figure 6), then tighten the setscrew in the
collar.
16. Securely connect the jumper assembly (supplied)
connectors to the four-pin connector and the onepin connector from the motor shaft (Figure 7).
LIGHT KIT
ADAPTER
FOUR-PIN
CONNECTOR
SINGLE-PIN
CONNECTOR
Figure 8
19. Lift the fan assembly from the styrofoam and
remove the center styrofoam section. Turn the fan
assembly over and carefully position it on the
upper styrofoam section so that the hanger
ball/downrod assembly is at the top (Figure 9).
SETSCREW
COLLAR
FAN MOTOR AND
HOUSING ASSEMBLY
Figure 6
UPPER
STYROFOAM
SECTION
17. Securely connect the black wire from the light kit
plate assembly to the blue wire from the motor
shaft using a wire connector (supplied) (Figure
7). Connect the white wire from the plate
assembly to the white wire from the motor shaft
using a wire connector (supplied).
Figure 9
6
20. Position one fan blade on the flange assembly
and secure by installing the left and right blade
holder caps using two 10-32 x 3/8” pan head
screws (supplied) for each holder cap (Figure 10).
Install the remaining four fan blades using the
same procedure.
!
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
10-32 X 3/8"
PAN HEAD SCREW
(2 PER HOLDER CAP)
!
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
FLANGE
ASSEMBLY
RIGHT BLADE
HOLDER CAP
LEFT BLADE
HOLDER CAP
OUTLET
BOX
Figure 10
21. You have now completed the initial assembly of your
new ceiling fan. You can now proceed with hanging
and wiring your fan.
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
How to Hang
Your Ceiling Fan
!
HANGER
BRACKET
Figure 12
TAB
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 13). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 12).
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 11).
!
CEILING
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
AT LEAST
7'
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY.
OUTLET
BOX
FLOOR
Figure 11
!
WARNING
HANGER
BRACKET
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan
Support”.
HANGER BALL/
DOWNROD ASSEMBLY
1. Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 12.)
Figure 13
!
7
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and the
hanger bracket.
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
3. Using wire connectors (supplied), make wiring
connections as follows (Figure 14 and 15):
a. Connect the white fan wire and the white supply
wire to the white receiver wire (AC IN/
MOTOR N).
b. Connect the black fan wire to the black receiver
wire (TO MOTOR L).
c. Connect the black supply wire to the black/white
receiver wire (AC IN L).
d. Cut off the ends of the blue and yellow receiver
wires and strip back insulation 1/2-inch from the
ends of the wires.
e. Connect the blue fan wire to the blue receiver
wire (BOTTOM LIGHT).
f. Connect the yellow fan wire to the yellow
receiver wire (UPPER LIGHT).
g. Connect the green ground wires from the
hanger bracket and the hanger ball to the supply
ground wire (bare or green).
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box
before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan and light kit or receiver.
1. Pull the wire leads, coming from the end of the
downrod, and the supply wires through the open
side of the hanger bracket. (Figure 14).
2. Position the SW105 Receiver (supplied) in the
ceiling cover so that the flat side of the receiver
faces up and the open portion of the receiver is to
the right, as shown in Figure 14.
OUTLET BOX
BLACK SUPPLY WIRE
HANGER BRACKET
BLACK FAN WIRE
HANGER BRACKET
GROUND WIRE
(GREEN)
BLACK/WHITE RECEIVER WIRE
BLUE FAN WIRE
HANGER BALL
GROUND WIRE
(GREEN)
BLUE RECEIVER
WIRE
OPEN
PORTION OF
RECEIVER
HERE
SUPPLY GROUND
WIRE (GREEN OR
BARE)
YELLOW FAN WIRE
YELLOW RECEIVER WIRE
RECEIVER
BLACK RECEIVER WIRE
WHITE SUPPLY
WIRE
WHITE RECEIVER WIRE
WHITE FAN WIRE
CEILING COVER
WIRE CONNECTOR
Figure 14
8
SW105 RECEIVER
BLACK/WHITE RECEIVER WIRE
BLACK
SUPPLY
WIRE
WHITE RECEIVER WIRE
BLACK RECEIVER WIRE
WHITE
SUPPLY
WIRE
BLUE RECEIVER WIRE
YELLOW RECEIVER WIRE
WHITE FAN WIRE
BLUE FAN WIRE
BLACK FAN WIRE
YELLOW FAN WIRE
DOWNROD
Figure 15
!
WARNING
OUTLET BOX
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
HANGER
BRACKET
1-1/4"
THREADED
STUDS (2)
4. After connections have been made, separate the
white and green wires from the black, blue and
yellow wires.
5. Carefully turn the wires upward and insert them up
through the open side of the hanger bracket and
into the outlet box. Push the green and white wires
into one side of the outlet box; push the black, blue
and yellow wires into the other side of the outlet
box.
RECEIVER
CEILING
COVER
Figure 16
Final Assembly
1. Screw the two 1-1/4” threaded studs (supplied) into
the tapped holes in the hanger bracket (Figure 16).
2. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 17).
3. Secure the ceiling cover in place by installing two
lockwashers and two knurled knobs (supplied)
(Figure 17). Tighten the knurled knobs securely
until the ceiling cover fits snugly against the ceiling
and the hole in the ceiling cover is clear of the
downrod.
4. Screw in three 40-watt (maximum) candelabra
base lamps in the uplight assembly sockets and
three 60-watt (maximum) candelabra base lamps in
the light kit plate sockets for the lower light.
CEILING COVER
1-1/4"
THREADED
STUD
LOCKWASHER
KNURLED KNOB
Figure 17
!
9
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
5. Obtain the die cast glass holders and light kit glass
from the protective bags.
6. Position the light kit glass carefully on a convenient
surface with the open side face down.
7. Remove the protective cover from the adhesive
backed material on the glass holders (Figure 18).
LIGHT KIT
GLASS
PROTECTIVE COVER ON
ADHESIVE BACKED MATERIAL
TURN KNURLED KNOB
SCREW SEVERAL TURNS
INTO THE GLASS HOLDER
DIE-CAST GLASS
HOLDER
Figure 20
Figure 18
11. Raise the light kit glass assembly and insert the
two knurled knobs through the two keyholes in
the light kit adapter. Turn the light kit glass
assembly counterclockwise to engage the
knurled knob screws in the slots (Figure 21).
Carefully reach between the fan blade flanges
and the light kit glass and securely tighten the
two knurled knob screws.
DIE CAST
GLASS HOLDER
8. Firmly press the die cast glass holders into
position on the light kit glass (Figure 19).
LIGHT KIT
GLASS
LIGHT KIT ADAPTER
KNURLED KNOB
SCREW
ROTATE LIGHT KIT GLASS
COUNTERCLOCKWISE
Figure 19
DIE CAST
GLASS HOLDER
LIGHT KIT GLASS
VIEWED FROM TOP
9. Repeat these procedures for the second die cast
holder.
10. Carefully turn the light kit glass assembly over.
Thread two knurled knob screws (supplied)
several turns onto the die cast glass holders
(Figure 20). Leave approximately 3/16” of the
stud threads revealed.
Figure 21
12. Your ceiling fan is now installed and wired and
ready for use.
10
Setting Operating
Frequency of Wall Control
and Receiver (Figure 22)
Battery Installation
of Wall Control
!
Your wall control and receiver have code switches
which must be set in one of 16 possible code
combinations. The four levers (numbered 1, 2, 3, and
4) on the switches are factory-set in the ON (up)
position. Change the switch settings as follows:
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box.
The SW116 wall control transmits the command
signals via radio waves to the SW105 receiver
installed in the ceiling fan ceiling cover. The
SW105 receiver is required for the SW116 wall
control to function. Power for the SW116 wall
control comes from the 12V battery, located in the
wall control.
Replacement 12V batteries recommended are
Duracell MN21, Eveready A23, and GP23A.
1. Install the 12V battery (supplied) into the wall
control (Figure 23).
2. The SW116 wall control is supplied with a white or
almond color cover. Choose the style that best
suits your needs and snap the cover onto the wall
control (Figure 23).
1. Slide the four switch levers in the wall control to
your choice of ON (up) or down positions. Use a
ball-point pen or small screwdriver and slide the
levers firmly up or down.
2. In the receiver, slide the four switch levers to the
same positions as set in the wall control. Make
sure the levers on both switches are in the same
positions, otherwise the fan will not operate.
SW105 RECEIVER
CODE
SWITCH
HIHI
U/L
U/L
MED
MED
D/L
D/L
WALL CONTROL
LEVERS
LOW
LOW
1
REV
REV
2
3
4
FAN OFF
ON
ON
1
2
3
EMERSON
4
RECEIVER SWITCH
LEVERS
HIHI
SW116
WALL
CONTROL
U/L
U/L
MED
MED
D/L
D/L
LOW
LOW
Figure 23
REV
REV
FAN OFF
SW116 WALL
CONTROL
Figure 22
WALL
CONTROL
COVER
12V BATTERY
3. Install the wall control onto the outlet box using the
supplied screws (Figure 24).
4. Install decorator faceplate (included) using the two
screws provided. Leave wall control in “OFF” mode
until fan installation is completed (Figure 24).
CODE
SWITCH
DECORATIVE
FACEPLATE
OUTLET BOX
HI
U/L
MED
D/L
LOW
REV
FAN OFF
EMERSON
SW116 WALL CONTROL
FACEPLATE
SCREW (2)
Figure 24
11
WALL CONTROL
SCREW (2)
Operating Your
Ceiling Fan
5. To turn the lights on and off, press and release the
U/L (uplight) button or the D/L (downlight) button.
The lights will turn on at the light level previously
set (see Step 4).
Red light turns on when any button is pressed.
If the light does not come on, replace your battery.
IMPORTANT
Fan installation must be completed, including the
installation of the fan blades, before testing of the
remote control.
Your SW116 Fan/Light Wall Control (Figure 25) has
full control of your fan, lights, and airflow direction.
1.To set the desired fan speed, push the HI, MED, or
LOW buttons to operate your fan on high, medium
or low speed (See Figure 25).
2.To reverse the direction the fan is turning, press the
REV button. The direction the fan turns will change
each time the REV button is pressed.
3.To turn your fan off, press the FAN OFF button.
4. To set the level of light brightness, press and hold
the U/L (uplight) button or the D/L (downlight)
button. The light brightness will continue to
increase then decrease while the button is held
down. When the light is at the desired brightness,
release the button.
HI
MED
U/L
D/L
LOW
REV
FAN OFF
EMERSON
Figure 25
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and if no installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is not guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
12
Maintenance
Accessories
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
!
1. Ceiling Fan Controls (see store or catalog).
2. Downrod Extension Kits (see store or catalog).
!
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
WARNING
!
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson. Substitution of parts or accessories not
designated for use with this product by Emerson
could result in personal injury or property damage.
NOTE: Periodically check the tightness of the
knurled knobs securing the light kit glass in the
light kit adapter. Tighten if necessary.
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble
!
shooting your fan.
Trouble Shooting
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
2. Loose power line connections to the fan.
1. Check main and branch circuit fuses or circuit
breakers.
!
WARNING: Make sure main power is turned off.
2. Check line wire connections to fan
3. Fan/Light Wall Control is OFF.
3. Turn ON Fan/Light Wall Control.
4. Code switches in remote control/receiver are not
set in the same position.
4. Check that both code switches are set in the same
positions.
2. Fan sounds noisy.
1. Blades not attached to fan.
2 Screws holding blades to flanges are loose.
1. Attach blades to fan before operating.
2. Tighten screws securely.
3. Fan wobbles
excessively.
1. Setscrew in motor coupling is loose.
2. Setscrew in hanger ball/downrod assembly is
loose.
3. Hanger bracket and/or ceiling outlet box is not
securely fastened.
4. Fan blades out of balance.
1. Raise motor cover and tighten setscrew securely.
2. Tighten the setscrew in the hanger ball/downrod
assembly.
3. Tighten the hanger bracket screws to the outlet box,
and/or secure outlet box.
4. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
Or use supplied balancing kit to balance blades.
13
Repair Parts
1
2
3
5
6
25
4
31
7
8
30
8
9
7
HI
U/L
MED
D/L
LOW
REV
3
10
FAN OFF
29
EMERSON
12
11
13
26
14
17
19
16
15
15
17 18
20
28
21
24
27
22
23
14
Repair Parts Listing
Key
No.
1
2
4
9
10
14
15
16
18
19
20
21
22
23
26
3
5
6
7
8
11
12
13
17
24
25
27
28
29
30
31
–
Description
Bracket Assembly, Hanger
Hanger ball/downrod Assembly
Cover, Ceiling
Capacitor, Auxiliary
Cover, Motor Coupling
Motor Assembly
Flange Assembly with Hub
Blade Assembly (Full set for one fan)
Cap, Blade Holder (Left)
Cap, Blade Holder (Right)
Light Kit Adapter
Light Kit Plate Assembly
Light Kit Glass
Die Cast Glass Holder
Uplight Lead Assembly
Loose Parts Bag, containing:
Threaded Stud, 8-32 x 1-1/4” (4)
Wire Connector (7)
Setscrew Wrench, 5/32”
Lockwasher (4)
Knurled Knob (4)
Clip, Hairpin
Pin, Clevis
Setscrew
Blade Screw, 10-32 x 3/8” (21)
Phillips Head Screw, 8-32 x 3/8” (3)
Setscrew Wrench, 3/16”
Knurled Knob Screw (2)
Jumper Assembly - 762150
Wall Control, Fan/Light,
SW116 (transmitter)
Receiver, Remote Control,
SW105
Reversing Module (supplied
with SW105 Receiver)
Owners Manual
Model No.
CF2455PW00
760732
761632-23
761795-6
761453
761621-21
762508
763227-6
763201-7
763199-6
763200-6
763282-6
763283
761745
763265-6
761790
763243-1
—
—
—
—
—
—
—
—
—
—
—
—
—
CF2455BS00
760732
761632-17
761795-3
761453
761621-15
762508
763227-3
763201-3
763199-3
763200-3
763282-3
763283
761745
763265-3
761790
763243
—
—
—
—
—
—
—
—
—
—
—
—
—
CF2455ORB00
760732
761632-37
761795-8
761453
761621-25
762508
763227-7
763201-8
763199-7
763200-7
763282-7
763283
761745-1
763265-7
761790
763243-1
—
—
—
—
—
—
—
—
—
—
—
—
—
763310
763310
763310
762400
762400
762400
—
BP7337
—
BP7337
—
BP7337
Before discarding packaging material, be certain all
parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label
attached to the top housing.
For repair parts, phone 1-800-654-3545.
15
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson Electric Co. ceiling fan against
all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime from the date you purchased your ceiling fan. All other
components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO
COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement
can be provided, Emerson Electric Co. will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED
PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL,
REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP
YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized
service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers
shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized
service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center.
Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible
for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and
tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON ELECTRIC CO. IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND
CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of
use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was
damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Printed in China 11/06
Part No. F40BP73370000
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant ¥ St. Louis, MO 63136
Form No. BP7337