Electrolux EOG 601 Specifications

Gas built-in oven
Please read this instruction booklet before using the appliance
Models EOG 601
Important Safety Information
You MUST read these warnings carefully before installing or using the oven. If you need
assistance, contact our Customer Care Department on 08705 950950
Do not use this oven if it is in contact with water and never
operate it with wet hands.
Take great care when heating fats and oils as they will
ignite if they become too hot.
Always use oven gloves to remove and replace food in the
Ensure that all control knobs are in the OFF position
when not in use.
Do not leave cookware containing foodstuffs, e.g. fat or
oil in or on the oven in case it is inadvertently switched
When using other electrical appliances, ensure the
cable does not come into contact with the hot surfaces
of the oven.
This appliance must be installed and serviced by a
competent person as stated in the Gas Safety
(Installation and Use) Regulations Current Editions
and the IEE Wiring Regulations.
For appliances installed in the Republic of Ireland
please refer to NSAI-Domestic Gas Installations
I.S.813 Current Editions and the ETCI Rules for
Electrical Installations.
This oven is heavy. Take care when moving it.
Remove all packaging, both inside and outside the oven,
before using the oven.
Do not attempt to modify the oven in any way.
The use of a gas cooking appliance results in the
production of heat and moisture in the room in which
it is installed. Ensure that the kitchen is well
ventilated: keep natural ventilation holes open or
install a mechanical ventilation device (mechanical
extractor hood).
Prolonged intensive use of the appliance may call for
additional ventilation, for example opening a window,
or more effective ventilation, for example increasing
the level of mechanical ventilation where present.
Child Safety
This oven is designed to be operated by adults. Do not
allow children to play near or with the oven.
The oven gets hot when it is in use. Children should be
kept away until it has cooled.
Maintenance and Cleaning
Only clean this oven in accordance with the instructions.
This appliance cannot be cleaned with steam or with
a steam cleaning machine.
The oven should be kept clean at all times. A build-up of
fats or other foodstuffs could result in a fire, especially in
the grill pan.
Always allow the oven to cool down and switch off the
electrical supply before carrying out any cleaning or
maintenance work.
This oven should only be repaired or serviced by an
authorised Service Engineer and only genuine approved
spare parts should be used.
Environmental Information
During Use
After installation, please dispose of the packaging with
due regard to safety and the environment.
This oven is intended for domestic cooking only. It is not
designed for commercial or industrial purposes.
Appliances become very hot with use, and retain their
heat for a long period after use. Care should be taken
to avoid touching heating elements inside the oven.
When disposing of an old appliance, make it unusable,
by cutting off the cable. Remove any door catches, to
prevent small children being trapped inside.
Do not block any of the oven vents. Never line any part
of the oven with aluminium foil.
Do not allow heatproof cooking material, e.g. roasting
bags, to come into contact with oven elements.
Never place plastic or any other material which may melt
in or on the oven.
Do not place sealed cans or aerosols inside the oven.
They may explode if they are heated.
Do not hang towels, dishcloths or clothes from the oven
or its handle.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product.
For more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where you
purchased the product.
For the User
Important Safety Information
Description of the Appliance
Before the First Use
Using the Oven
Using the Gas Oven
Using the Gas Grill
Cleaning the Oven
Something Not Working
Replacing the Oven Light
Service and Spare Parts
Guarantee Conditions
For the Installer
Instructions for the Installer
Building in
Electrical Connection
Gas connection
Conversion from Natural to LPG Gas
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an
Hints and Tips
Environmental information
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
This appliance complies with the following
E.E.C. Directives:
* 90/396 (Gas Directive)
* 73/23 - 90/683 (Low Voltage Directive);
* 93/68 (General Directives);
* 89/336 (Electromagnetical Compatibility
Directive) .
and subsequent modifications
Description of the Appliance
6 5 4
1. Control panel
2. Minute minder
3. Oven Light & Electric Grill
control knob
4. Gas oven control knob
5. Grill control light
6. Mains on light
7. Grill
8. Oven lamp
9. Oven cavity bottom plate
10. Rating plate
Oven accessories
Anti-tip shelf (x 2)
Grill Pan
Control Knob for the Oven Light
and the Electric Grill
Grill / Roasting pan
Oven Light - The oven light will be on
without any cooking function.
Grill Function - The heat comes from the
electric grill element only.
Range of temperature adjustment for the
electric grill (from a minimum of about 50ºC
to a maximum of about 200°C).
Mains on Light
The Mains on Light will come on when the “Light & Grill”
control knob is set.
Grill Control Light
The Grill Control Light will come on when a temperature
is set for the electric grill with the “Light & Grill” control
knob. The light will remain on until the correct temperature
is reached. It will then cycle on and off to show the
temperature is being maintained.
Gas Oven Control Knob
Oven burner off
150 - 240
Range of temperature
adjustment for conventional
Minute minder
The minute minder will mark the end of a timed period
with an acoustic alarm. The maximum timing is 60
Turn the minute minder knob clockwise to the maximum
time position, then turn it back to the required time.
The minute minder will not affect in any way the oven
operation, if it is in use.
Cooling fan
The cooling fan operates during cooking. Air is expelled
through vents between the oven door and the control
panel, as shown in the diagram.
The cooling fan may run on after the oven is switched off
to keep the controls cool. This is quite normal.
Before the First Use
Remove all packaging, both inside and outside
the oven, before using the appliance.
Before first use, the oven should be heated without food.
During this time, an unpleasant odour may be emitted.
This is quite normal.
1. Light the gas oven burner (see “Using the Gas
Oven”) and set the temperature to 240.
2. Open a window for ventilation.
3. Allow the oven to run empty for approximately
60 - 90 minutes.
Using the Oven
Always cook with the oven door closed.
Stand clear when opening the drop down oven
door. Do not allow it to fall open - support the
door using the door handle, until it is fully open.
The oven has four shelf levels, and is supplied
with two shelves. The shelf positions are counted
from the bottom of the oven as shown in the
It is important that these shelves are correctly
• Attention! - Do not place objects directly on the
oven base and do not cover it with aluminium foil
while cooking, as this could cause a heat
build-up which would affect the baking results
and damage the oven enamel. Always place
pans, heat-resisting pans and aluminium foils
on the grid which has been inserted in the oven
Condensation and steam
When food is heated it produces steam in the same way
as a boiling kettle. The oven vents allow some of this
steam to escape. However, always stand back from
the oven when opening the oven door to allow any
build up of steam or heat to release.
If the steam comes into contact with a cool surface on
the outside of the oven, e.g. a trim, it will condense and
produce water droplets. This is quite normal and is not a
fault with the oven.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
Using the Gas Oven
During cooking, the door should be opened as little
as possible to avoid heat loss, and excessive fuel
the oven gas burner:
To1. ignite
Press the Gas Oven control knob, turn it to 240
and wait for the flame to come on. This may
take 10-15 seconds. Do not release the knob
until the burner ignites. It is possible to check
the flame through the holes in the bottom of the
2. Upon ignition, keep the knob pressed for about
5/10 seconds, then release it and turn it to the
required setting.
If the oven burner does not light even after 15
1. Release the control knob and turn it to the “Off
2. Open the oven door and wait for at least one
minute before trying to light the oven burner
If the oven burner accidentally goes out, turn the
oven knob to the “Off” position and wait at least
one minute before trying to light the burner again.
Oven safety device
The gas oven features a Safety Device (“Thermocouple”);
if the flame should extinguish for any reason, the device
will stop the gas flow.
Hints and Tips
Use any oven proof cookware which will withstand
temperatures of 250°C.
Baking trays, oven dishes, etc. should not be placed
on the oven base.
Do not use baking trays larger than 30 cm x 35 cm
(12 in x 14 in) as they will restrict the circulation of
heat and may affect performance.
Cooking Chart
Beef with bone
2 or 3
Beef without bone
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
20 minutes per lb
+ 20 minutes
25 minutes per lb
+ 25 minutes
20-25 minutes per lb
+ 20-25 minutes
25 minutes per lb
+ 25 minutes
25 minutes per lb
+ 25 minutes
30 minutes per lb
+ 30 minutes
30 minutes per lb
+ 30 minutes
21/2 hours
2 or 3
2 or 3
25 minutes
35 minutes
varies according to
the vegetable
Fruit Tart
Fruit Pie
Sausage Rolls
Choux Pastry
Vol au Vents
Jam Tarts
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
35 minutes
35 minutes
20 minutes
25-30 minutes
15 minutes
10-15 minutes
Egg Custard in a
Bain Marie
2 or 3
2 or 3
2 or 3
1-1 1/4 hours
1 1/2 hours
1 1/2 hours
2 or 3
3 1/2-4 hours
2 or 3
2 1/2 hours
2 or 3
2 or 3
25-35 minutes
1 3/4-2 hours
20-30 minutes
35-45 minutes
20-25 minutes
2 or 3
30-40 minutes
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3 (*)
40-50 minutes
15-20 minutes
25-35 minutes
15-20 minutes
25-35 minutes
The effects of dishes on cooking results
Rich Fruit
Cake 8"
Plain Fruit Cake
Madeira Cake
Small Cakes
Ginger Bread
Dishes and tins vary in their thickness, conductivity,
colour, etc. which affects the way they transmit heat to
the food inside them.
A Aluminium, earthenware, oven glassware and bright
shiny utensils reduce cooking and base browning.
B Enamelled cast iron, anodized aluminium,
aluminium with non-stick interior and coloured
exterior and dark, heavy utensils increase cooking
and base browning.
1lb Loaves
2lb Loaves
Rolls and Buns
Tea Rings
(* ) Change trays over halfway through the cooking time
Grilling must be carried out with the oven door
The grill pan handles must be removed from
the pan during grilling. Always use oven gloves
to remove and replace the grill pan handles.
Ensure that you support the grill pan when
removing it from the oven.
How to Use the Electric Grill
1. Turn the “Light & Grill” control knob anticlockwise after
. Please note that the circle stripe on the
indicates the temperature setting (the
thicker the stripe, the higher the temperature).
2. Adjust the grid and grill pan runner position to allow
for different thicknesses of food. Position the food close
to the top element for faster cooking and further away
for more gentle cooking.
Cooking chart
Cooking time depends on the thickness of the meat and
not on its weight.
Type of food
Bacon rashers
Chicken joints
Gammon rashers
Lamb chops
Pork chops
Sausages (turning as required)
Steaks (average thickness)
Mins per side
15 - 20
6 - 12
10 - 15
10 - 12
6 - 10
Well done 8 - 12
1 - 11/2
Preheat the grill on a full setting for a few minutes before
sealing steaks or toasting. Adjust the heat setting and
the shelf as necessary, during cooking.
The mains on light will come on when the "Light-Grill
& Fan" control knob is set.
The grill control light will remain on until the correct
temperature is reached. It will then cycle on and off to
show that the temperature is being maintained.
The action of the cooling fan will depend on how long the
grill has been used and at what temperature. It may not
switch in at all at lower temperature settings nor run on
where the oven has only been used for a short time.
Hints and Tips
Most foods should be placed on the grid in the grill
pan to allow maximum circulation of air to lift the food
out of the fats and juices. Food such as fish, liver and
kidneys may be placed directly on the grill pan, if
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish lightly
with a little oil or melted butter to keep them moist
during cooking.
Accompaniments such as tomatoes and mushrooms
may be placed underneath the grid when grilling meats
When toasting bread, we suggest that the top runner
position is used with the grid in its 'high' position.
The food should be turned over during cooking, as
Cleaning the Oven
Before cleaning always allow the cooling fan to
cool the oven down before switching off at the
electricity supply.
This appliance cannot be cleaned with steam or
with a steam cleaning machine.
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm.
Wipe the oven over with a soft cloth soaked in warm
soapy water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives should
also be avoided.
External cleaning
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
• Household detergent and bleaches
• Impregnated pads unsuitable for nonstick saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Clean the outer and inner door glass using warm soapy
water. Should the inner door glass become heavily soiled
it is recommended that a cleaning product such as Hob
Brite is used.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not observed
the glass panel may shatter.
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Centre
who will be pleased to advise further.
Oven Shelves and Shelf
To clean the oven shelves and the shelf supports, soak in
warm soapy water and remove stubborn marks with a well
wetted soap impregnated pad. Rinse well and dry with a
soft cloth.
The shelf supports can be removed for easy cleaning.
1. Undo the fixing nut which keep the shelf support in
place. When carrying out this operation, keep the
shelf support in position with the other hand.
2. Then, disengage the rear hook and take off the
shelf support.
Please, ensure the retaining nuts are secure when
refitting the shelf support.
Models in stainless steel or
We recommend to clean the oven door using only a wet
sponge and dry it after cleaning with a soft cloth.
Never use steel wool, acids or abrasive products as they
can damage the oven surface.
Clean the oven control panel following the same
Replacing the Oven Light
Disconnect the appliance.
If the oven bulb needs replacing, it must comply with the
following specifications:
- Wattage power: 15W,
- Voltage: 230V (50 Hz),
- Resistant to temperatures of 300°C,
- Connection type: E14.
These bulbs are available from your local Service
Force Centre.
replace the faulty bulb:
To1. Ensure
the oven is disconnected from the
electrical supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace with the
new one.
4. Refit the glass cover.
5. Reconnect to the electrical supply.
Something Not Working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
The gas oven does not light nor the electric grill
Check that the oven is switched on at the wall
Check that the power supply has not been interrupted
before the cooling fan has had time to cool the oven down
The gas oven does not light.
Check that there is not a problem with your gas supply
Food is cooking too quickly or too slowly
Check that you are using the recommended temperature settings and shelf positions.
The oven is not cooking evenly
Check that the oven is installed properly.
Check that you are using the recommended temperature settings and shelf positions.
The oven light does not work
Check the light bulb, and replace it if necessary (see
"Replacing the Oven Light")
Refer to the contents of this booklet, especially to
Steam and condensation settle on the food and
the oven cavity.
If after all these checks, your hob still does not operate
correctly, contact your local Electrolux Service Force
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
the chapter “Using the Gas Oven”.
Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Electrolux Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit
the website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
For general enquiries concerning your Electrolux
appliance or for further information on Electrolux
products, please contact our Customer Care Department
by letter or telephone at the address below or visit our
website at www.electrolux.co.uk
Customer Care Department
55-77 High Street
08705 950950 (*)
* calls to this number may be recorded for training
For Customer Service in the Republic of Ireland please
contact us at the address below:
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: +353 (0) 1 4090 751
Email: service.eid@electrolux.ie
Guarantee Conditions
Electrolux Guarantee conditions
European Guarantee
We, Electrolux, undertake that if, within 12 months of
the date of the purchase, this Electrolux appliance or
any part thereof is proved to be defective by any reason
only of faulty workmanship or materials, we will, at our
option, repair or replace the same FREE OF ANY
CHARGE for labour, materials or carriage on condition
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
The guarantee starts from the date you first
purchased your product.
The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be
transferred to another user.
Your new home is within the European Community
(EC) or European Free Trade Area.
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
All service work under this guarantee must be
undertaken by a Electrolux Service Centre.
The product is installed taking into account
regulations in your new country.
Any appliance or defective part replaced shall become
the Company's property.
This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
This guarantee does not cover:
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
Appliances found to be in use within a commercial or
similar environment, plus those which are the subject
to rental agreements.
Products of Electrolux manufacture which are not
marketed by Electrolux.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
+33 (0)
+49 (0)
800 234 7378
+39 (0)
800 117511
+46 (0)
20 78 77 50
+44 (0)
1753 219898
Instructions for the Installer
Technical Data
Model Name:
EOG 601
Oven Burner
Natural Gas G20 20mbar
Cabinet Dimensions
Minimum aperture height
Minimum aperturedepth
Minimum aperture width
Electric Grill
Oven light
Cooling fan
Total electric rating
Supply voltage (50 Hz)
2,700 W (Natural gas)
2,500 W (LPG)
1,650 W
15 W
25 W
40 W
230 V
580 mm
550 mm
560 mm
Important Safety Requirements
This appliance must be installed in accordance with
the Gas Safety (Installation and Use) Regulations
(current addition) and the I.E.E. Wiring Regulations.
Detailed recommendations are contained in the
following British Standard Codes of Practice - B.S. 6172,
B.S. 5440: Part 2 and B.S. 6891: Current Editions.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S. 813 Current
Editions and the ETCI Rules for Electrical Installations.
Provision for Ventilation
This appliance is not connected to a combustion
products evacuation device. It shall be installed and
connected in accordance with the current installation
regulations. Particular attention shall be given to the
relevant requirements regarding ventilation.
Building in
Location of appliance
The appliance may be located in a kitchen, a kitchen/
diner or bedsitting room but not in a bathroom, shower
room or bedroom.
It is essential that there is a minimum clearance of 4mm
between the top surface of the appliance and the inside
top of the cabinet. The unit must be fitted into a cabinet
conforming to dimensions given in these pages.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S 813 Current
Edition Section 7- Permitted Locations of Appliance.
This oven unit may be used in a Built-in or a Built-under
situation (see relevant diagrams). If the appliance is to
be built-under a hob, it is recommended that the hob be
installed before the oven unit.
The room containing the appliance should have an air
supply in accordance with BS. 5440: Part 2 Current
Edition. All rooms require an openable window or
equivalent and some rooms will require a permanent vent
as well. For room volumes up to 5m3 an air vent 100cm2
is required; for room volumes between 5m3 and 10m3, an
air vent with a minimum area of 50cm2 is required. If the
room has a door which opens directly to the outside, no
air vent is required. For room volumes that exceed 11m3
no air vent is required.
If there are other fuel burning appliances in the same
room, B.S. 5440: Part. 2: Current Editions should be
consulted to determine the requisite air vent
For appliances installed in the Republic of Ireland please
refer to the NSAI-Domestic Gas Installation I.S. 813
Current Editions Table Four.
Please ensure that when the oven is installed it is
easily accessible for the engineer in the event of a
The surround or cabinet into which the oven will be built
must comply with these specifications:
the dimensions must be as shown in the relevant
the materials must withstand a temperature increase
of at least 60°C above the ambient temperature;
proper arrangements must be made of a continuous
supply of air to the oven to prevent the oven
Dimensions of the oven and recess required are given
in the relevant diagrams (in millimetres).
Built-in recess dimensions
Dimensions are given in millimetres
Built-under recess dimensions
(kitchen unit with feet)
Dimensions are given in millimetres
Built-under recess
(kitchen unit
without feet)
Dimensions are
given in millimetres
Securing the oven to the cabinet
1. Fit the oven into the cabinet recess
2. Open the oven door
3. Secure the oven to the kitchen cabinet with four
wood screws, which fit the holes provided in the
oven frame (see diagram).
Electrical Connection
The oven is designed to be connected to 230V (50Hz)
electricity supply.
The oven has an easily accessible terminal block which
is marked as follows:
Letter L
Letter N
or E
Live terminal
Neutral terminal
Earth terminal
The cable used to connect the oven to the electrical
supply must comply to the specifications given below.
For Uk use only
Min. size
Cable / flex
• 13 A socket
• 13 A
spur box
2.5 mm2
3 core
13 A
• Cooker
2.5 mm2
twin and
13 A
For Europe use only
Min. size Cable/flex
Cable / flex type
1.5 mm2
H05 RR-F
13 A
Live wire
Neutral wire
It is necessary that you install a double pole switch
between the oven and the electricity supply (mains), with
a minimum gap of 3mm between the switch contacts and
of a type suitable for the required load in compliance with
the current rules.
The switch must not break the yellow-green earth wire
at any point. The earth wire should be 2 cm longer than
the live and neutral wires.
After installation and connecting, the cable must be
placed so that it cannot at any point reach a temperature
of more than 60°C above the ambient temperature.
Before the oven is connected, check that the main fuse
and the domestic installation can support the load and
that the power supply is properly earthed.
The manufacturer disclaims any responsibility should
these safety measures not be carried out.
Earth wire
at least 2 cm longer
Gas connection
Connecting the appliance to the
gas supply
metallic pipe(*)
The use of rubber flexible hoses is not
The gas supply connection ramp is located in the upper
side of the oven, right behind the control panel.
gas supply ramp
out the gas connection:
To1. carry
Partially insert the oven in the recess (about 30
cm.) and operate on the connection ramp from
above. The gas connection can be carried out
according to one of the following procedures:
A) connection with flexible metallic pipes (*)
(with maximum length up to 2 metres only) —
screw the feed pipe to the 1/2“ connection
ramp, inserting the supplied gasket between
the pipe and the ramp;
B) connection with rigid metallic pipe (soft
copper - minimum diameter: 8-10 mm) — insert
the copper pipe into the connection ramp after
fitting the proper nut and olive onto the copper
pipe using a male / female adapter (not
control panel
(*) For mainland Europe only
rigid metallic pipe
male/female adapter
gas supply ramp
2. Tighten the nuts by means of a 22 mm spanner.
Care must be taken to keep the ramp in position
and not to cause any stress to the gas supply
3. Completely insert the oven in the recess and
secure it as indicated in the relevant paragraph.
4. Check the perfect sealing of the connection using
leak detection fluid. Never use a flame for the
leak-proof test !
control panel
Check the gas supply ramp and the gas
connection pipe are not squeezed while the
oven is positioned into the recess.
The use of a gas cooking appliance results in the
production of heat and moisture in the room in
which it is installed. Ensure that the kitchen is
well ventilated: keep natural ventilation holes
open or install a mechanical ventilation device
(mechanical extractor hood).
gas supply ramp
control panel
Prolonged intensive use of the appliance may
call for additional ventilation, for example opening
a window, or more effective ventilation, for
example increasing the level of mechanical
ventilation where present.
Conversion from Natural to LPG Gas
The replacement/conversion from Natural to
LPG should only be undertaken by a
competent and qualified engineer.
It is important to note that this model is designed for use
with natural gas but can be converted for use with LPG
providing the correct injectors are fitted. The gas rate is
adjusted to suit.
Replacement of gas oven
burner injector
To replace the gas burner oven injector, follow this
1. Remove the bottom plate of the oven (“A”) to access
the gas oven burner;
2. Undo the two fixing screws (“C”) which keep the gas
oven burner in place
3. Gently slide the oven gas burner off the injector
support (“D”) and slowly move it to the left hand side.
Check that the burner bush does not slip off the burner
mouthpiece, and take care not to cause stress to the
spark plug connection wire (“E”) and the thermocouple
(“F”) conductor;
3. With a 7 mm socket spanner unscrew and remove
the gas burner injector (“D”), and replace it with the
required one (see Table on this page);
4. Reassemble the burner following the same procedure
The oven burner does not require any primary
air regulation.
Replacement of Gas Type Label
Once both the injectors for the gas oven burner and the
gas grill burner have been replaced, take the Gas Type
Label which is relevant to the new gas type and place it
over the old one (it is located near the gas connection
ramp). The replacement label is supplied with the injector
Gas Oven Burner Data
1/100 mm
(1/100 mm)
Natural Gas
28-30 / 37
Minimum level adjustment
of gas oven burner
This procedure must be undertaken by a
competent and qualified engineer only.
1. Disconnect the appliance from the
mains supply.
Remove all the knobs.
Open the oven door and locate the ventilation
grill which is fixed right below the control panel.
Remove the rubber caps from the ventilation grill
then undo the two fixing screws (“A”) and finally
take the grid off.
Undo the two fixing screws (“B”) which keep the
control panel in place, then take it off the
With a thin bladed screwdriver, completely
tighten the minimum level adjustment screw (“C”).
Refit all the oven parts following the above
described procedure backwards.
Restore the mains supply.
Do not restore the mains supply if all the
removed parts have not been fitted back in
their original position.
9. Light the oven gas burner (see the relevant
chapter), set the gas oven control knob on 240
and let the oven heat for 10 minutes at least.
10.Check that the oven gas burner flame does not
fail when quickly turning the gas oven control
knob from 240 to 150.
11.Should the oven gas burner flame fail when
performing point 10, repeat the whole procedure
from point 1 to point 10, until a small regular
flame is obtained on the complete gas oven
burner crown.
55-77 High Street
Tel.: 08705 950950
© Electrolux plc 2004
The Electrolux Group. The world’s No.1 choice.
Grafiche MDM - Forlì
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are
sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.