advertisement
XL-HP505
SERVICE MANUAL
No. S1402XLHP505/
MICRO COMPONENT SYSTEM
MODEL
XL-HP505
XL-HP505 Micro Component System consisting of XL-
HP505 (main unit) and CP-HP505 (speaker system).
• In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used.
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] IMPORTANT SERVICE NOTES (FOR
U.S.A. ONLY) ................................................. 1-1
[2] SPECIFICATIONS ......................................... 1-1
[1] ADJUSTMENT ............................................... 2-1
[3] Standard Specification of Stereo System
Error Message Display Contents ................... 2-5
CHAPTER 3. MECHANICAL DESCRIPTION
[1] REMOVING AND REINSTALLING THE
MAIN PARTS ................................................. 3-1
[2] DISASSEMBLY .............................................. 3-3
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS
[1] NOTES ON SCHEMATIC DIAGRAM ............6-1
[2] TYPES OF TRANSISTOR AND LED ............6-1
[3] WIRING SIDE OF P.W.BOARD/SCHE-
MATIC DIAGRAM ..........................................6-2
[1] TROUBLESHOOTING ..................................7-1
[1] FUNCTION TABLE OF IC .............................8-1
CHAPTER 5. CIRCUIT DESCRIPTION
[1] WAVEFORMS OF CD CIRCUIT .................... 5-1
[2] VOLTAGE....................................................... 5-2
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used for after sales service only.
The contents are subject to change without notice.
XL-HP505
CHAPTER 1. GENERAL DESCRIPTION
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
[1] IMPORTANT SERVICE NOTES (FOR
U.S.A. ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the following safety checks.
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials, cabinet, terminal board, adjustment and compartment covers or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor (See diagram).
* Connect the resistor connection to all exposed metal parts having a return path to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.
VTVM
AC SCALE
1.5k ohms
10W
TO EXPOSED
METAL PARTS
0.15 µ F
TEST PROBE CONNECT TO
KNOWN EARTH
GROUND
All check must be repeated with the AC line cord plug connection reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp. AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the audio product to the owner.
[2] SPECIFICATIONS
■
General
Power source
Power consumption
Dimensions
AC 120 V, 60 Hz
80 W
Width: 7-1/4" (185 mm)
Height: 10-1/4" (260 mm)
Depth: 12" (307 mm)
13.7 lbs. (6.2 kg) Weight
■
Amplifier
Output power
Output terminals
Input terminals
75 watts minimum RMS per channel into 6 ohms from 100 Hz to 20 kHz, 10% total harmonic distortion
Speakers: 6 ohms
Headphones: 16 - 50 ohms (recommended:
32 ohms)
Subwoofer pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Video/Auxiliary (audio signal): 500 mV/47 k ohms
■
CD player
Type
Signal readout
D/A converter
Frequency response
Dynamic range
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser pickup
1-bit D/A converter
20 - 20,000 Hz
90 dB (1 kHz)
■
Tuner
Frequency range FM: 87.5 - 108 MHz
AM: 530 - 1,720 kHz
■
Cassette deck
Frequency response
50 - 14,000 Hz (normal tape)
Signal/noise ratio 50 dB (recording/playback)
Wow and flutter 0.3 % (WRMS)
■
Speaker
Type
Weight
2-way type speaker system
2" (5 cm) tweeter
Maximum input power
5-1/8" (13 cm) woofer
150 W
Rated input power 75 W
Impedance
Dimensions
6 ohms
Width: 6-1/2" (165 mm)
Height: 10-1/4" (261 mm)
Depth: 9-11/16" (246 mm)
6.2 lbs. (2.8 kg)/each
Specifications for this model are subject to change without prior notice.
1 – 1
XL-HP505
[3] NAMES OF PARTS
1
2
3
4
5
6
7
8
1
2
3
9
1 2 3 4 5
21
22
6 7
14
15 16 17
23
24
25
26
27
10
11
12
13
14
15
16
17
18
19
20
■
Front panel
1. Disc Trays
2. Timer Indicator
3. Power On/Stand-by Button
4. Clock/Timer Button
5. CD Track Down or Fast Reverse, Tape Fast Wind,
Tuner Preset Down, Time Down Button
6. Tape Reverse Play Button
7. Tape Reverse Mode Select Button
8. Cassette Compartment
9. Headphone Jack
10. Disc Tray Open/Close Button
11. Disc Number Select Buttons
12. CD Direct Play Button
13. Illumination Light
14. Volume Control
15. CD Track Up or Fast Forward, Tape Fast Wind,
Tuner Preset Up, Time Up Button
16. Memory/Set Button
17. Equalizer Mode Select Button
18. Extra Bass/Demo Mode Button
19. CD Play or Repeat, Tape Forward Play Button
20. CD or Tape Stop Button
21. CD Button
22. Tuner (Band) Button
23. Tape Button
24. Video/Auxiliary Button
25. Tape Record Pause Button
26. Tuning Up Button
27. Tuning Down Button
4
5
6
7
8 9 10
11 12 13
8
■
Display
1. Disc Number Indicators
2. CD Play Indicator
3. CD Pause Indicator
4. Memory Indicator
5. CD Repeat Play Indicator
6. CD Indicator
7. Extra Bass Indicator
8. Tape Reverse Play Indicator
9. Tape Forward Play Indicator
10. Tape Reverse Mode Indicator
11. FM Stereo Mode Indicator
12. Daily Timer Indicator
13. FM Stereo Receiving Indicator
14. Tape Record Indicator
15. Sleep Indicator
16. Timer Play Indicator
17. Timer Recording Indicator
■ Rear panel
1. Cooling Fan
2. Speaker Terminals
3. AC Power Cord
4. FM 75 Ohms Antenna Terminal
5. FM Antenna Ground Terminal
6. AM Loop Aerial Jack
7. Video/Auxiliary (Audio Signal) Input Jacks
8. Subwoofer Pre-output Jack
■ Speaker system
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire
1
2
3
4
1 – 2
XL-HP505
1
2
3
4
5
6
7
11
12
13
8
9
10
15
16
17
18
19
14
20
21
22
23
24
■ Remote control
1. Remote Control Transmitter
2. Disc Number Select Buttons
3. CD Track Down or Fast Reverse, Tape Fast Wind,
Tuner Preset Down, Time Down Button
4. Volume Up and Down Buttons
5. Disc Direct Search Buttons
6. Equalizer Mode Select Button
7. Extra Bass Button
8. Power On/Stand-by Button
9. CD Button
10. Tuner (Band) Button
11. Tape Button
12. Video/Auxiliary Button
13. CD Track Up or Fast Forward, Tape Fast Wind,
Tuner Preset Up, Time Up Button
14. Clock/Timer Button
15. CD Random Button
16. CD Clear/Dimmer Button
17. CD Stop Button
18. Tape Reverse Play Button
19. Tape Stop Button
20. Memory/Set Button
21. CD Pause Button
22. CD Play or Repeat Button
23. Tape Forward Play Button
24. Tape Record Pause Button
1 – 3
XL-HP505
CHAPTER 2. ADJUSTMENTS
[1] ADJUSTMENT
1. MECHANISM SECTION
• Driving Force Check
Torque Meter
Play: TW-2111
Specified Value
Over 80 g
• Torque Check
Torque Meter
Play: TW-2111
Fast forward: TW-2231
Rewind: TW-2231
Specified Value
30 to 80 g.cm
70 to 180 g.cm
70 to 180 g.cm
2. TUNER SECTION fL: Low-range frequency fH: High-range frequency
• AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
Test Stage Frequency Frequency
Display
AM IF
AM Band
Coverage
450 kHz
—
AM Tracking 990 kHz
1,602 kHz
531 kHz
990 kHz
Setting/
Adjusting
Parts
T351
(fL): T306
1.1 ± 0.1 V
(fL): T303
*1
*2
*1
Instrument
Connection
*1. Input: Antenna Output: TP302
*2. Input: Antenna Output: TP301
• FM RF
Signal generator: 1 kHz, 40 kHz dev., FM modulated
Test Stage
FM Band
Coverage
FM RF
Frequency
—
98.00 MHz
(10-30 dB)
Frequency
Display
87.50 kHz
Setting/
Adjusting
Point
T301 (fL):
1.3 ± 0.1 V
98.00 MHz L312
*1
*2
Instrument
Connection
*1. Input: Antenna Output: TP301
*2. Input: Antenna Output: Speaker terminal
• FM IF
Signal generator: 10.7MHz FM modulated
Test Stage Frequency Frequency
Display
IF 10.7 MHz 98 MHz
Setting/
Adjusting
Point
T302
(Turn the core of transformer T302 fully counterclock wise)
*1
Instrument
Connection
*1. Input: Antenna Output: TP301
• Tape Speed
Normal speed
Test Tape Adjusting
Point
MTT-111 Variable
Resistor in motor.
Specified
Value
Instrument
Connection
3,000 ± 30 Hz Speaker Terminal (Load resistance: 6 ohms)
TAPE MECHANISM
Tape
Motor
Variable Resistor in motor
Figure 1
AM
LOOP
ANTENNA
TUNER PWB-C
20
CNP301
AM TRACKING fL
IC301
TP301
C393 T302
FM IF
T301
FM OSC
L312
T303
FM RF
T306
AM BAND
COVERAGE fL
T351
AM IF
TP302
Figure 2 ADJUSTMENT POINTS
3. CD SECTION
• Adjustment
Since this CD system incorporates the following automatic adjustment functions, readjustment is not needed when replacing the pickup. Therefore, different PWBs and pickups can be combined freely.
Each time a disc is changed, these adjustments are performed automatically. Therefore, playback of each disc can be performed under optimum conditions.
Items adjusted automatically
1) Offset adjustment (The offset voltage between the head amplifier output and the VREF reference voltage is compensated inside the
IC.)
* Focus offset adjustment
* Tracking offset adjustment
2 – 1
XL-HP505
2) Tracking balance adjustment
3) Gain adjustment (The gain is compensated inside the IC so that the loop gain at the gain crossover frequency will be 0 dB.)
* Focus gain adjustment
* Tracking gain adjustment
4. CD ERROR CODE DESCRIPTION
Error
01
10*
11*
20*
21*
22*
31
Explanation
When Pickup set inner position, inner switch cannot detect
'ON' level for 10 secs.
CAM error. Can't detect CAM switch when CAM is moving.
When it detect cam operation error during initialize process.
TRAY error. Can't detect TRAY switch when TRAY is moving.
When it detect TRAY operation error during initialize process.
When it detect invalid TRAY switch during normal operation.
When it change to CD function, DSP cannot read initial data.
* 'CHECKING'
If Error is detected, 'CHECKING' will be displayed instead of 'ER-
CD**'. 'ER-CD**' display will only be displayed when error had been detected for the 5th times.
2 – 2
[2] TEST MODE
• Setting the test mode
During stand-by mode, press ON/STAND-BY button while pressing down the button and X-BASS/DEMO button. then, press the CD button to enter the test mode.
C D T E S T
OPEN/CLOSE operation is using manual.
IL isn’t done
IL isn’t done
<< >>,<< >>buttons make pick's slide possible.
IL isn’t done
<<PLAY>> key input.
A to page 2-4
Do TOC IL. Do normal play.
When these following key is input into PLAY key, track number can be appoint directly.
<<MEMORY>> key input.
<<
<<
<<
1>> key: Track 4
2>> key: Track 9
3>> key: Track 15
––––––––
Adjustment result automatically will display as below for each 2 sec: a) "FOF_XXXX" b) "TOF_XXXX" c) "TBAL_XX" d) "TGAN_XX" f) "FGAN_XX" g) "RFLS_XX"
<<STOP>> key input.
STOP explanation: a) Focus off set b)Tracking off set c)Tracking balance d)Tracking Gain f) Focus Gain g) RF level shift
VOL — Last memory
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
= "FOF_XXXX"
= "TOF_XXXX"
= "TBAL_XX"
= "TGAN_XX"
= "FGAN_XX"
= "RFLS_XX"
XL-HP505
2 – 3
XL-HP505
A
<<MEMORY>> key input.
Laser ON.
<<MEMORY>> key input.
Tracking OFF play at that specific point.
<<MEMORY>> key input.
Tracking ON play from that specific point.
<<MEMORY>> key input.
Adjustment result automatically will display as below for each 2 sec : a) "FOF_XXXX" b) "TOF_XXXX" c) "TBAL_XX" d) "TGAN_XX" f) "FGAN_XX" g) "RFLS_XX"
<<STOP>> key input.
STOP
Sliding the PICKUP with<< in STOP mode.
>>, << explanation: a) Focus off set b)Tracking off set c)Tracking balance d)Tracking Gain f) Focus Gain g) RF level shift
VOL — Last memory
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
= "FOF_XXXX"
= "TOF_XXXX"
= "TBAL_XX"
= "TGAN_XX"
= "FGAN_XX"
= "RFLS_XX"
>> button must only be
2 – 4
XL-HP505
[3] Standard Specification of Stereo System Error Message Display Contents
CD
Error Contents
Pickup Mechanism Error.
DISPLAY
'ER-CD01'
CD Changer Mechanism Error.
'ER-CD**' (*)
Notes
PU-IN SW Detection NG.
10: CAM SW Detection NG during normal operation
11: CAM SW Detection NG during initialize process
20:TRAY SW Detection NG during normal operation
21:TRAY SW Detection NG during initialize process
DSP COMMUNICATION ERROR.
TUNER
CD DSP Communication Error.
'ER-CD31'
Focus Not Match/IL Time Over.
'NO DISC'
PLL Unlock.
FM
87.50
MHz
PLL Unlock.
(*) CHECKING:
If CD changer mechanism error is detected, 'CHECKING' will be display instead of 'ER-CD**'. 'ER-CD**' display will only be display when error had been detected for the 5 th times.
Speaker abnormal detection and +B PROTECTION display
In case speaker abnormal detection or +B PROTECTION had occurred, it can be check by pressing 'POWER', '
Computer version number will displayed as "U******".
' and 'X-BASS' button. Micro-
Press ‘VIDEO/AUX’ button during version number display and then press ‘POWER’, ‘MEMORY/SET’ and ‘VIDEO/AUX’ button. Display will show "S**
B**". S is referring to speaker abnormal detection and B is referring to +B PROTECTION. ** is in hex valve.
+B PROTECTION is condition when irregular process occur on power supply line.
BEFORE TRANSPORTING THE UNIT
The following process need to be taken after set tapering/parts replacement.
1. Press the ON/STAND-BY button to enter stand-by mode.
2. While pressing down the be displayed as "U******".
button and the X-BASS/DEMO button, press the ON/STAND-BY button. The Micro Computer version number will
3. Press OPEN/CLOSE button until "WAIT"--> "FINISHED" appears.
4. Unplug the AC cord and the unit is ready for transporting.
2 – 5
XL-HP505
CHAPTER 3. MECHANICAL DESCRIPTION
[1] REMOVING AND REINSTALLING THE
MAIN PARTS
1. TAPE MECHANISM SECTION
Perform steps 1 to 9 of the disassembly method to remove the tape mechanism.(see page 3-3,3-4)
1.1. How to remove the Record/Playback Head (See Fig. 1)
1. When you remove the screws (A1) x 2 pcs and (A2) x 1 pc., the record/playback head can be removed.
1.2. How to remove the Pinch Roller (See Fig. 2)
1. Carefully bend the pinch roller pawl in the direction of the arrow
<A>, and remove the pinch roller (B1) x 1 pc., in the direction of the arrow <B>.
NOTE: When installing the pinch roller, pay attention to the spring mounting position.
1.3. How to remove the Belt (See Fig. 3)
1. Remove the main belt (C1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (C2) x 1 pc.
1.4. How to remove the Motor (See Fig. 4)
1. Remove the screws (D1) x 2 pcs., to remove the motor.
Erase Head
(A1)x2
Ø2x6mm
(A2)x1
Ø2x9mm
Figure 1
Clutch Ass'y
Record/Playback
Head
Pinch Roller
(B1)x1
Pull
<B>
Figure 2
<A>
Pinch
Roller
Pawl
FF/REW
Belt
(C2)x1
FF/REW
Clutch
Motor
Main Belt
(C1)x1
Flywheel
Figure 3
Motor
Clutch Ass'y
(D1)x2
Ø 2.6x5mm
Figure 4
3 – 1
2. CD MECHANISM SECTION
Perform steps 1 to 4 and 11 to 12 of the disassembly method to remove the CD mechanism.(see page 3-3,3-4)
2.1. How to remove the Optical Pickup (See Fig. 1)
1. Remove the screws (A1) x 2 pcs and shaft (A2) x 1 pc.
2. Remove the stop washer (A3) x 1 pc and gear (A4) x 1 pc.
3. Remove the optical pickup.
NOTE: After pulling out the optical pickup connector, wrap the tip of it with conductive aluminium foil or the like to protect the optical pickup from the static electricity.
2.2. How to remove CD Disc (See Fig. 2~5)
1. When CD is at play position, Rotate reduction gear C clock-wise as shown in Figure 2 Until disk tray is at stalk position, then rotate further to eject the disk tray so that CD can be removed from the tray.
2. In another case, if CD mechanism is at tray No. 1 play position and to remove CD located in tray No. 3, the procedure is as follows:
If the gear up down board is located at tray No. 1 position, then rotate gear clock-wise until it is at stalk position. Rotate reduction gear D (Figure 3) to move the CD mechanism to tray No. 3 position.
This is confirmed by checking the gear up down board position by the marking as indicated on the main chassis as shown in Figure 4.
Guide Tray
Disc Tray
CD Disc
XL-HP505
Stop Washer
(A3) x1
Optical Pickup
CD
Mechanism
(A1) x2
ø2.6 x5mm
Figure 1
Reduction gear C
Gear
(A4) x1
Shaft
(A2) x1
Front Rear
Figure 2
Reduction gear D
Up Down
Figure 3
CD Disc
CD At play position.
Gear up down board
CD At stalk position.
Figure 5
Mark 1
(DISC 1)
Mark 3
(DISC 3)
Mark 2
(DISC 2)
Mark 5
(DISC 5)
Mark 4
(DISC 4)
Figure 4
3 – 2
XL-HP505
[2] DISASSEMBLY
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance:
1) Take cassette tape and compact disc out of the unit.
2) Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit.
3) Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling.
4) Take sufficient care on static electricity of integrated circuits and other circuits when servicing.
Rear
Panel Top
(A1) x1
ø3x8mm
(A1) x2
ø3x8mm
(A1) x1
ø3x8mm
Cabinet
Front Panel
(A1) x3
ø3x8mm
STEP
1
2
3
4
5
6
7
8
9
10
11
12
11
12
REMOVAL
Cabinet
Rear Panel Top
CD Changer unit
PROCEDURE
1. Screw..........................(A1) x11
1. Screw............................(B1) x2
1. Hook.............................(C1) x2
2. Socket..........................(C2) x1
3. Flat Cable.....................(C3) x1
1. Screw...........................(D1) x9 Rear Panel Bottom
Front Panel
Turner PWB
Main PWB
1. Screw...........................(E1) x3
2. Flat Cable....................(E2) x2
3. Socket..........................(E3) x1
4. Hook............................(E4) x2
1. Screw............................(F1) x1
2. Socket..........................(F2) x1
1. Screw...........................(G1) x2
2. Socket.........................(G2) x4
1. Screw...........................(H1) x4
1. Screw............................(J1) x1
Power PWB
Terminal PWB
Display PWB 1. Knob.............................(K1) x1
2. Screw...........................(K2) x 8
3. Flat Cable....................(K3) x 1
Tape Mechanism 1. Screw...........................(L1) x 4
Headphones PWB 1. Screw..........................(M1) x 1
CD Servo PWB
(Note 1)
1. Screw...........................(N1) x2
2. Flat Cable...................(N2) x 2
3. Socket..........................(N3) x1
CD Mechanism 1. Screw...........................(P1) x4
2. Screw...........................(P2) x4
Note 1:
After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of the connector so as to protect the optical pickup from electrostatic damage.
FIGURE
1
1
2
2
2,3
3
5
5
6
6
7
4
4
5
2
3
2,4
4
(B1) x2
ø3x10mm
(A1) x2
ø3x8mm
(A1) x2
ø3x8mm
CD Changer
Unit
CD Servo PWB
(C3) x1
Rear
Panel Bottom
(D1) x9
ø3x8mm
Rear
Panel Bottom
Figure 1
Pull
Hook
(C1)x1
(C2) x1
Front Panel
Pull
Hook
(C1)x1
Main PWB
Headphones
PWB
(E2) x1
(F1) x1
ø3x8mm
(G1) x1
ø3x10mm
(E1) x1
ø3x10mm
Figure 2
(E3) x1
Tape
Mechanism
Front Panel
(E2) x1
(F2) x1
Hook
(E4)x1
Pull
Turner PWB
Main PWB
Hook
(E4)x1
Pull
(E1) x2
ø3x10mm
Figure 3
3 – 3
(G2) x2
Main PWB
(G1) x1
ø3x6mm
(G2) x2
(H1) x4
ø4x6mm
XL-HP505
(P2) x4
ø2.6x10mm
CD Mechanism
CD Changer
Unit
Power PWB
(J1) x1
ø3x6mm
Figure 4
Terminal PWB
(K1) x1
Display PWB
(K3) x1
Front Panel
(K2) x8
ø2.6x8mm
Tape
Mechanism
Headphones
PWB
Cassette
Holder
(L1) x4
ø3x10mm
Figure 5
(M1) x1
ø3x10mm
CD Changer
Unit
Figure 7
STEP REMOVAL
Woofer/
Tweeter
PROCEDURE
1. Net Frame(A1) x1
2. Catching Holder(A2) x4
3. Screw(A3) x4
4. Front Panel(A4) x1
5. Screw(A5) x6
Tweeter
FIGURE
8
Front Panel
( A4 ) x1
Net Frame
( A1 ) x1
(A3)x2
ø3.5x16mm
(A2)x2
(A5)x2
ø3.5x12mm
(A5)x4
ø3.5x12mm
Woofer
Screwdriver
(A2)x2
(A3)x2
ø3.5x16mm
Figure 8
(N3) x1
(P1) x2
ø3x10mm
(N2) x2
(P1) x2
ø3x10mm
(N1) x2
ø3x10mm
Figure 6
CD Servo PWB
3 – 4
XL-HP505
CHAPTER 4. DIAGRAMS
[1] BLOCK DIAGRAM
FM ANTENNA
TERMINAL
SO302
B.P.F
BF301
AM LOOP
ANTENNA
CNP301
2
1
1
IC301
TA7358AP
FM FRONT END
6
9
3 4 5 7 8
FM RF L312
FM OSC
T301
T302
FM IF
CF302
OSC
BUFF
Q302
1 2
T351
AM IF
450 kHz
CF352
4
MIX OUT
24 23 21 7
FM/AM OUT
18
+B5
5
10.7 MHz
CF351
ZD351
5.1V
X351
456 kHz
9 8
FM DET
17 13
L 14
IC303
LA1832S
FM IF DET.
FM MPX./AM IF
R 15
16 12 20
AM
TRACKING
T303
AM BAND
COVERAGE
T306
+B6
VT X352
4.5 MHZ
IC302
LC72131
PLL(TUNER)
20 1
OSC
22 15 16
+B5
11 3 4 5 6
7 9 10 21
17
+B5
FM+B
SWITCHING
Q360
FM
Q361
FROM CD SECTION
CNP2
SWITCHING
REC /P.B. HEAD
L-CH
TAPE R-CH
AC BIAS
Q101-
Q104
CNS2
1
2
3
L(TA)
R(TA)
2
23
L REC
R REC
9
16
REC
11
12
15
P.B
13
JK690
L
R
VIDEO/AUX
TAPE
TUNER
CD
L 9
R
L
16
10
R
L
15
11
R
L
14
12
R 13
+B5
4
21
L
R
PB
IC601
LC75341
DI
CE
CLK
AUDIO PROCESSOR
7 18 8 17 3 23
+B5
1
2
24
21
4
R
L
Q107
Q108
MUTING
REC/PLAY
H/N
7
18
L
R
REC
IC101
AN7345K
PLAYBACK AND RECORD
/PLAYBACK AMP.
–20dB
ATT
Q601
Q602
Q603
Q604
+B5
+B4
+B7(A_+5V)
A_+10V
LD_+8V
+B8(D_+5V)
+B9(SW_+5V)
ERASE
HEAD
SWITCHING
Q105
Q106
+B5
Q114
SWITCHING
Q112 Q113
SWITCHING
+B5
BIAS
OSC
Q111
L103
Q109
SWITCHING
BIAS
Q110
BIAS
+B_PROTECT Q851
+B10
Figure 4-1 BLOCK DIAGRAM (1/3)
UN
4 – 1
XL-HP505
IF
Q603
Q604
5V)
5V)
V)
A_+10V
LD_+8V
Q851
B10
1 2 5 21
FL701
FL DISPLAY
28 31 32 41 44 45
MOTOR/
SOLENOID
DRIVER
Q701,702
Q712~715
TAPE
MECHANISM
ASS'Y
+B10
+B10
LED701
+B5 Q711
LED708
38 48 43 44 46 59 40 25 13
69
REMOCON 39
78 AVDD 34
79
36
41
42
45
80
VLOAD
33
P_IN
SMUTE
IC701
TIME LED
IXA002AW
(Serial No.31000001~402XXXXX)
VOL_LED
IXA007AW
(Serial No.402XXXXX)
IXA020AW
(Serial No.402XXXXX~)
VOL_JOG
PROTECT
RESET
SYSTEM MICROCOMPUTER
31
30
29
10
56
83
84 53
100
VDD -20dBATT
1 2 3 4 6 7 11 12 15 16 21 24 17 18 19 20
SP_RLY 47
SP DET +B10
XL700
4.19403MHz
+B10
+B3
REMOTE SENSOR
+B10
1 RX701
3
2
+B10
KEY
SW701-SW705
SW709-SW728
VOLUME
VR701
+B9(SW_+5V)
+B_PROTECT
Q703
RESET
+B10
+B4(8V)
+B7(A_5V)
+B8(D_5V)
TO CD SECTION
DRIVER
Q906
FAN MOTOR
M971
M +B7(A_5V)
L
R
18
14
2
5
7
IC901
STK412-000
POWER AMP.
1
6
VH–
11
8
L-OUT
R-OUT
VH+
D801
VL–
IC851
AN80T53
MULTI REGULATOR
VL+
D802
F802
4A 125V
F801
4A 125V
Q901
Q904
Q905
RL914
RELAY
PT801
POWER
TRANSFORMER
(MAIN)
+B3
SO901
SPEAKER TERMINAL
JK701
HEADPHONES
JK953
SUB WOOFER
PRE-OUT
6 7 1 4 3 5 2
F804
2A 125V
VF2
–VF
VF1
UNSW_5.6V
P_IN
AC_RLY
IC854
AN78L05
VOLTAGE
REGULATOR
Q841
RELAY
DRIVER
VOLTAGE
REGULATOR
Q801
D842-D845
F803
2A 125V
T.F
PT841
POWER
TRANSFORMER
(SUB)
Figure 4-2 BLOCK DIAGRAM (2/3)
4 – 2
RL841
RELAY
XL-HP505
TO MAIN SECTION
FROM DISPLAY SECTION
PHOTO INTERRUPTER
TRAY MOTOR
XOUT
XIN
MOT_A-/CONT4
MOT_A+/CONT5
MO_SPEED/CONT6
MO_B+/CONT3
MO_B-/CONT2
SPDO
SLDO
TDO
FDO
MO_SPEED
CONT1
FOCUS/TRACKING/ SPIN/SLED
PVCC2
PVCC1
SVCC
VREFIN
PGND1
SGND
PGND2
VO6+
VO6–
VO5+
VO5–
Figure 4-3 BLOCK DIAGRAM (3/3)
4 – 3
SPINDLE MOTOR
SLED MOTOR
XL-HP505
CHAPTER 5. CIRCUIT DESCRIPTION
[1] WAVEFORMS OF CD CIRCUIT
1 IC1 21
T
Stopped
CH1=500 mV
DC 10:1
1
FDO
CH3=500 mV
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
2 IC1 22 3
TDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.000 V
CH2 :
CH3 :
CH4 :
0.0 V
0.000 V
0.00 V
=Record Length=
Main : 100 K
Zoom : 2 K
CH1 v/DIV
500 mV
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay : 0.0 ns
Hold off : 0.2 µs
1 IC1 21
Stopped
CH1=500 mV
DC 10:1
CH2=10 V
DC 10:1
1
FDO
3 IC1 68
T
2
DRF
CH3=1 V
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
4
IC1 17
3
TE
-3 div -1 div
=Filter=
Smoothing : ON
0 div
=Offset=
CH1 : 0.000 V
BW : FULL
CH Position To
CH2 :
CH3 :
CH4 :
0.0 V
0.00 V
0.00 V
+1 div +3 div
=Record Length=
Main : 100 K
Zoom : 2 K
CH2
Position
0.20 div
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay : 0.0 ns
Hold off : 0.2 µs
Stopped
CH1=200 mV
DC 10:1
T
CH2=500 mV
DC 10:1
1 IC1 21
T
2
FDO
1999/04/07 09:51:15
500 ms/div
(500 ms/div)
NORM:20 kS/s
6 IC1 24
1
SPDO
7 IC1 76
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.000 V
CH2 :
CH3 :
CH4 :
0.000 V
0.00 V
0.00 V
=Record Length=
Main : 100 K
Zoom : 2 K
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay : 2.924 ms
Hold off : 0.2 µs
Stopped
CH1=500 mV
DC 10:1
3
PDO1
CH3=1 V
DC 10:1
1999/04/05 17:33:17
CH4=1 V
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
4
8 IC1 77 PDO2
T
1 IC1 21
1
FDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
CH2 :
0.000 V
0.0 V
CH3 :
CH4 :
0.00 V
0.00 V
=Record Length=
Main : 100 K
Zoom : 2 K
CH1 v/DIV
500 mV
=Trigger=
Mode : AUTO
Type : EDGE CH2
Delay :
Hold off :
0.0 ns
0.2 µs
Stopped
CH1=2 V
DC 10:1
T
1999/04/07 09:25:28
500 ns/div
(500 ns/div)
NORM:200 MS/s
T
9
IC1 39
1
DOUT
5 IC1 4
Stopped
CH1=10 V
DC 10:1
T
CH2=1 V
DC 10:1
4 IC1 17
2
TE
Vp-p=1.0 V~1.3 V
0.5 mV/div,0.5 µsec/div
100 ms/div
(100 ms/div)
NORM:100 kS/s
3 IC1 68
T
1
DRF
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
CH2 :
0.0 V
0.00 V
CH3 :
CH4 :
0.00 V
0.00 V
=Record Length=
Main :
Zoom :
100 K
2 K
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
Hold off :
2.924 ms
0.2 µs
5 – 1
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
CH2 :
0.00 V
0.00 V
CH3 :
CH4 :
0.00 V
0.00 V
=Record Length=
Main :
Zoom :
1 K
100
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
Hold off :
2.887 ms
0.2 µs
Stopped
CH1=2 V
DC 10:1
T
CH2=2 V
DC 10:1
CH3=2 V
DC 10:1
1999/04/05 20:50:17
5 µs/div
(5 µs/div)
NORM:100 kS/s
10 IC1 57
1
LRSY
11
IC1 58
12 IC1 59
2
DATACK
T
3
DATA
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.00 V
CH2 :
CH3 :
CH4 :
0.00 V
0.00 V
0.00 V
=Record Length=
Main : 5 K
Zoom : 100
CH3 v/DIV
2 V
=Trigger=
Mode : AUTO
Type : EDGE CH3
Delay : 0.0 ns
Hold off : 0.2 µs
XL-HP505
[2] VOLTAGE
IC1
PIN
NO. VOLTAGE
1 3.20 V
1.61V
2
3
4
1.61 V
1.60 V
1.61 V 5
6
7
3.06 V
1.65 V
1.65 V 8
9
10
11
1.65 V
1.65 V
1.48 V
0 V 12
13
14
1.65 V
0 V
1.65 V 15
16
17
1.47 V
1.48 V
0 V 18
19
20
21
0 V
0 V
1.60 V
0 V 22
23
24
1.61 V
1.61 V
0 V 25
26
27
0 V
3.20 V
0 V 28
29
30
31
3.20 V
0 V
0 V
1.59 V 32
33
34
1.60 V
3.20 V
0 V 35
36
37
0 V
0 V
0 V 38
39
40
41
0 V
0 V
3.61 V
0 V 42
43
44
0 V
1.80 V
3.60 V 45
46
47
0 V
1.45 V
1.49 V 48
49
50
3.19 V
3.79 V
0 V 51
52
53
54
0 V
0 V
0 V
0 V 55
56
57
0 V
0 V
0 V 58
59
60
0 V
3.20 V
0 V 61
62
63
64
0 V
0.63 V
0 V
5.16 V 65
66
67
5.18 V
4.68 V
0 V 68
69
70
0 V
0 V
0 V 71
72
73
74
0 V
0 V
4.86 V
4.86 V 75
76
77
3.01 V
0 V
1.12 V 78
79
80
0 V
3.20 V
Q1
PIN
NO. VOLTAGE
3.2 V E
C
B
94.3 mV
3.2 V
PIN
NO. VOLTAGE
E
C
B
Q2
4.9 V
3.2 V
4.2 V
Q110
PIN
NO. VOLTAGE
-0.0 mV 1
2
3
9.9 V
15.1 V
IC2
PIN
NO. VOLTAGE
1 2.10 V
2.20 V 2
3
4
2.10 V
2.20 V
2.10 V 5
6
7
2.20 V
0 V
4.37 V 8
9
10
11
5.02 V
3.20 V
1.62 V
1.65 V 12
13
14
1.62 V
1.65 V
1.62 V 15
16
17
0 V
1.62 V
1.64 V 18
19
20
21
4.71 V
4.71 V
3.92 V
3.11 V 22
23
24
3.10 V
2.50 V
1.65 V 25
26
27
0 V
5.02 V
8.68 V 28
29
30
31
5.02 V
0.59 V
0.71 V
0 V 32
33
34
35
36
0 V
0 V
2.11 V
2.20 V
IC101
PIN
NO. VOLTAGE
4.16 V
0 V
3.42 V
0.57 V
0 V
0 V
0.41 V
2.03 V
0.57 V
0 V
0 V
0 V
0 V
0.57 V
2.03 V
0.44 V
0 V
0 V
0.58 V
3.45 V
3.35 V
0 V
0 V
6.97 V
20
21
22
23
24
13
14
15
16
17
18
19
10
11
12
8
9
6
7
3
4
5
1
2
7
8
5
6
IC301
PIN
NO. VOLTAGE
1 0 V
0 V 2
3
4
0.29 V
0.20 V
0 V
9
0.29 V
0.26 V
0.29 V
0.29 V
Q302
PIN
NO. VOLTAGE
E
C
B
2.1 V
0 V
0 V
Q360
PIN
NO. VOLTAGE
E
C
B
16.01 V
0.4 mV
10.01 mV
PIN
NO. VOLTAGE
E
C
B
Q601
0.3 mV
0.2 mV
0.3 V
3
4
1
2
IC302
PIN
NO. VOLTAGE
2.57 V
0 V
0 V
0 V
0 V 5
6
7
5.22 V
10.18 V
4.75 V 8
9
10
0 V
0 V
5.23 V 11
12
13
14
15
16
17
0 V
5.23 V
0 V
0 V
2.59 V
5.24 V
0 V 18
19
20
21
22
0 V
10.18 V
0 V
2.57 V
IC303
PIN
NO. VOLTAGE
1 1.97 V
5.15 V 2
3
4
1.97 V
1.98 V
0 V 5
6
7
0 V
5.21 V
3.59 V 8
9
10
11
12
13
14
5.15 V
0 V
2.01 V
1.25 V
2.27 V
1.13 V
1.10 V 15
16
17
1.95 V
0 V
1.29 V 18
19
20
2.08 V
1.29 V
1.95 V 21
22
23
24
1.95 V
5.15 V
3.65 V
IC601
7
8
5
6
PIN
NO. VOLTAGE
1 0 V
0 V 2
3
4
0 V
5.10 V
5.10 V
5.10 V
5.10 V
5.11 V
5.10 V 9
10
11
5.10 V
5.10 V
5.10 V 12
13
14
5.10 V
5.10 V
5.10 V 15
16
17
18
5.10 V
5.10 V
5.10 V
5.10 V 19
20
21
5.10 V
5.10 V
5.10 V 22
23
24
10.20 V
0 V
IC901
PIN
NO. VOLTAGE
46.70 V 1
2
3
22.90 V
10.80 V
-10.90 V 4
5
6
-22.90 V
-48.80 V
0 V 7
8
9
10
0 V
0 V
0 V
0 V 11
12
13
-47.40 V
47.50 V
-0.16 V 14
15
16
17
18
-0.16 V
-46.30 V
-0.17 V
-0.16 V
PIN
NO. VOLTAGE
1
6
7
8
9
2
3
4
5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
4.74 V
4.65 V
0 V
4.70 V
4.72 V
4.72 V
0 V
0 V
0 V
4.83 V
2.27 V
1.99 V
0 V
4.73 V
0 V
4.74 V
0 V
0 V
5.22 V
0 V
0 V
4.88 V
0 V
0 V
0 V
5.20 V
0 V
5.01 V
5.01 V
2.64 V
5.01 V
5.01V
0 V
0 V
5.01 V
1.67 V
5.20 V
5.01 V
4.87 V
0 V
2.02 V
0 V
13.10 V
0 V
0 V
4.74 V
0 V
4.61 V
0 V
0 V
IC701
PIN
NO. VOLTAGE
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
0 V
0 V
0 V
0 V
5.17 V
5.17 V
-29.70 V
0 V
-0.26 V
-0.24 V
-0.22 V
-0.20 V
-0.19 V
-0.19 V
-0.18 V
-0.17 V
-0.16 V
0 V
-29.90 V
-29.90 V
-29.90 V
-29.90 V
-29.90 V
-19.76 V
-27.40 V
-24.87 V
-22.29 V
-22.30 V
-30.13 V
-27.43 V
-14.60 V
-27.20 V
-19.30 V
-6.08 V
-21.85 V
-27.22 V
-21.89 V
-17.00 V
-27.38 V
-27.10 V
-27.07 V
-27.00V
-27.00 V
-27.35 V
-27.27 V
-27.11 V
-27.00 V
-27.07 V
-27.00 V
-26.83 V
IC851
PIN
NO. VOLTAGE
1 5.22 V
13.11 V 2
3
4
20.66 V
0 V
19.72 V 5
6
7
10.22 V
8.67 V
IC854
PIN
NO. VOLTAGE
1
2
3
5.66 V
0.61 V
9.33 V
Q603
PIN
NO. VOLTAGE
0.4 mV E
C
B
0.2 mV
0.7 mV
Q604
PIN
NO. VOLTAGE
0.4 mV E
C
B
0.1 mV
0.7 V
Q701
PIN
NO. VOLTAGE
E
C
B
12.9 V
0.8 mV
12.9 V
Q702
PIN
NO. VOLTAGE
15.9 V E
C
B
10.0 mV
12.9 V
Q703
PIN
NO. VOLTAGE
0.9 mV 1
2
3
4.5 V
0.9 mV
Q602
PIN
NO. VOLTAGE
E
C
B
0.3 mV
0.2 mV
0.7 V
PIN
NO. VOLTAGE
1
2
3
Q711
10.01 V
9.7 V
207.2 mV
PIN
NO. VOLTAGE
E
C
B
Q712
-392.1 mV
4.9 V
392.4 mV
Q713
PIN
NO. VOLTAGE
E
C
B
12.9 V
362.5 mV
12.9 V
Q714
PIN
NO. VOLTAGE
9.8 mV E
C
B
4.5 V
9.9 mV
PIN
NO. VOLTAGE
E
C
B
Q715
12.9 V
9.8 mV
12.9 V
PIN
NO. VOLTAGE
1
2
3
Q719
9.9 mV
5.10 V
9.8 mV
PIN
NO. VOLTAGE
E
C
B
PIN
Q841
24.1 mV
126.0 mV
0.8 V
NO. VOLTAGE
E
C
B
Q901
-0.18 mV
-0.18 mV
0.5 V
Q902
PIN
NO. VOLTAGE
E
C
B
0.16 mV
0.5 V
0.16 mV
Q903
PIN
NO. VOLTAGE
E
C
B
0.7 mV
0.5 V
-0.10 mV
Q904
PIN
NO. VOLTAGE
E
C
B
0.6 mV
0.5 V
-0.9 mV
Q801
PIN
NO. VOLTAGE
E
C
B
-29.12 V
-29.77 V
-42.4 V
PIN
NO. VOLTAGE
E
C
B
Q908
0.6 mV
0.5 V
0.8 mV
5 – 2
XL-HP505
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
[1] NOTES ON SCHEMATIC DIAGRAM
• Resistor:
To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means
1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression
“capacitance/withstand voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice.
REF. NO
SW1
SW1A
SW2
SW3
SW4
SW701
SW702
SW703
SW704
SW705
SW709
SW710
SW711
SW712
SW713
DESCRIPTION
CLAMP
PICKUP IN
TRAY SW1
TRAY SW2
DISC
ON/STAND-BY
CLOCK/TIMER
REVERSE MODE
REVERSE PLAY
PRESET DOWN
CD
TUNER (BAND)
VIDEO/AUX
TAPE
REC/PAUSE
POSITION
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
• The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section, indicates AM indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
REF. NO
SW714
SW715
SW716
SW717
SW718
SW719
SW720
SW721
SW722
SW723
SW724
SW725
SW726
SW727
SW728
DESCRIPTION
TUNING/TIME UP
TUNING/TIME DOWN
STOP
PLAY
PRESET UP
X-BASS/DEMO
EQUALIZER
MEMORY/SET
DIRECT PLAY
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
OPEN/CLOSE
POSITION
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
[2] TYPES OF TRANSISTOR AND LED
FRONT
VIEW
E C B
(S) (G) (D)
(1) (2) (3)
KRC102 S
KRC104 S
KRA107 S
KTA1504 Y
KTA1271 Y
KTA1273 Y
KTA1274 Y
KTA1504 GR
KTC3199 GR
KTC3200 GR
KTC3875 GR
KTC3203 Y
KTC3194 Y
SVC347S
SVC230C
FRONT
VIEW
6 – 1
XL-HP505
[3] WIRING SIDE OF P.W.BOARD/SCHEMATIC DIAGRAM
A
B
C
D
E
F
G
MAIN PWB-A1(1/2)
1
2
3
L-CH
A_GND
R-CH
R619
330
R618
330
FM SIGNAL
CD SIGNAL
AUX SIGNAL
PLAYBACK SIGNAL
RECORD SIGNAL
R617
2.2K
R616
2.2K
R613
390
R611
2.2K
R610
2.2K
R601 1K
R602 1K
R605
10K
C609
1
DI
2
CE
R607
3.3K
R05
0
1/50
3 VSS
4
LOUT
C607
0.15
C611
0.0022
C605
0.15
C613
C615
4.7/50
C617
C619
5
LBASS
6
LTRE
1/50
7
LIN
8
LSEL0
1/50
9
L4
1/50
10
L3
C621
C623
1/50
1/50
11
L2
12
L1
– +
IC601
LC75341
AUDIO PROCESSOR
– +
CCB
INTERFACE
– +
AUX
DECK
TUNER
CD
– +
CL
VD
VRE
ROU
RBAS
RTR
RI
RSEL
R
R
R
R
6-11 11 - E
CNP2
TO CD SERVO PWB
CNS2
1
2
3
4
5
6
7
8
R-CH
1
2
A_GND
3
L-CH
CD_GND
5
D_5V
6
A-5V
D_GND
7
8
LD+8V
4
9
BI601
+B
+B
+B
R645
0
TAPE MECHANISM
Ass'y(213)
ERASE HEAD
6
2
1
5
4
3
CNS102
6
2
1
5
4
3
HEAD PLATE
BLOCK
8
7
6
2
1
5
4
3
LD_+8V
7
23
CD_D_GND
A_+5V
11
D_+5V
10
CD_GND
26
24
CD_A_GND
+B
+B
BI102
ERASE
M_GND
T2_R2
A_GND
T2_R1
T2_L1
T2_L2
9.3V
9.3V
R146
10K
8.6V
Q112
R147
10K
R148
4.7K
KTA1504 GR
Q113
KRC104 S
0V
2
0V 1
3.4V
3
1
0V
2
3
3.4V
Q114
KRC104 S
R112 15K
0V
Q102
KTC3200 GR
R104 R108
47K
0V
0.7V
2.2K
0.7V
R106
3.3K
0V
0V
0V
C104 0V
180P(CH)
Q104
KTC3200 GR
C103
180P
0V
Q103
KTC3200 GR
0.7V
R105
3.3K
0V
0V
0.7V
R103
2.2K
Q101
KTC3200 GR
0V
0V
R107
47K
0V
R149
C141
100/16
150 +B
R116
56
R114
1K
C112
100/16
C114
0.033
C116
560P
C110
330P
R118 R120
100K 3.9K
24
1
R113
1K
23 22 21
–
+ 112K
Hich=T1
+
–
112K
2 3
C109
330P
R117 R119
100K 3.9K
4
C113
0.033
C111
100/16
R115
56
C115
560P
R122
12K
R124
6.8K
6.8K
20
R123
5
0V
REC_R
R138
10K
0.7V
R136
220K
R139
10K
Q
KTC3
0.7V
0
19
6
R128
5.6K
C126
22/16
18 17
Hich=CHROME
–
+
+
–
7 8
56K
16
56K
9
15 14 13
10 11 12
+
R111 15K
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1 2 3 4
Figure 6-2 SCHEMATIC DIAGRAM (1/10)
5
6 – 2
6
XL-HP505
1
CESSOR
– +
C653
220P
C601
220/16
CLK
24
VDD
23
+B
VREF
22
C603
22/16
C608
0.15
ROUT
21
RBASS
R1
20
C606
0.15
RTRE
19
RIN
RSEL0
18
C616
4.7/50
17
C614
1/50
R4
16
C618
1/50
R3
15
C620
1/50
R2
14
C622
1/50
13
R606
3.3K
R06
C624
1/50
0
C602
0.022
C610
1/50
C612
0.0022
R604
10K
R603
1K
R642
10K
R644
6.8K
R643
6.8K
R641
10K
+B +B
R691
6.8K
R690
6.8K
C691
390P
C690
390P
R693
39K
R692
39K
2
1
4
3
L-CH
JK690
VIDEO/AUX
R-CH
CHASSIS
GND
TUN_R
A_GND
TUN_L
D_GND
A_+10V
DO
CLK
DI
CE
CNP303
10
9
8
7
6
14
13
12
11
3
2
5
4
1
+B
R136
220K
R139
10K
0.7V
Q107
KTC3875 GR
0V
15 14 13
+B
10 11 12
R158
220
+B
11.6V
Q109
KTA1504 GR
0V
R141
4.7K
2
Q110
KRC104 S
3
1
0V
R142
82
(1/2W)
R143
47K
0V
0V
R144
22K
C138
0.0082
0V
R145
4.7
7
+B
TO DISPLAY PWB
6-9 11 - B
CNP701A
+B
+B
+B UNSW5.6V
21 25 19 8 9 22 6 12 17 5
TO MAIN PWB(2/2)
6-4 1 - D~H
4 16 15 14 13 18
8 9 10
Figure 6-3 SCHEMATIC DIAGRAM (2/10)
6 – 3
11
21
P_IN
SP_RLY
AC_RLY CON
SP_DET
CLK
DI
DO
CE
+B_PROTECT
D_GND
S_MUTE
T_BIAS
REC/PLAY
–20dB
M_+13V
SW_5V
A_+10V
–VF
VF1
VF2
CNP701B
5
4
7
6
3
2
1
12
11
10
9
8
17
16
15
14
13
21
20
19
18
1 FFC701
12
XL-HP505
A
B
C
D
E
F
10
11
12
7
8
9
5
6
3
4
1
2
L_CH
A_GND
R_CH
SP_RLY
SP_DET
M_+13V
+B
LD_+8V
+B
A_+10V
+B_PROTECT
+B
D_+5V
A_+5V
SW_+5V
+B
+B
R903
1K
+
-
-
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
IC901
STK412-000
POWER AMP.
C902
0.1/50
R912
100 (1/4W)
R910
1K
R958
100 (1/4W)
R908
1K
+B
FM SIGNAL
+B
–B
C917
0.01
R919
1.8K
Q902
KTC3875 GR
Q901
KTC3875 GR
R920
1.8K
C919
0.01
R917
0.1
(3W)
R922
0.1
(3W)
SP_DET
C946
0.1/50
ZD902
DZ12BSB
R925
1.5K
(1/2W)
ZD903
DZ12BSB
R926
1.5K
(1/2W)
Q903
KTC3875 GR
C920
3300/63
47K
R929
(1/4W)
D909
1N4004S
VH-
–B
R927
39K
(1/4W)
R928
39K
(1/4W)
VL-
C921 C922
4700/35 4700/35
VL+ VH+
C923
3300/63
R930
47K (1/4W)
D910
1N4004S
L902
3µH
R
L901
3µH
L
+B
+B
+B
+B
+B
+B
+B
–B
IC851
AN80T53
MULTI REGULATOR –B
+B
6 7
C859
22/25
1
C865
22/25
4 3 5 2
C854
220/25
C855
10/50
+B
Q851
KRC104 S
2 3
ZD804
DZ6.2BSA
D865
1
DS1SS133
R859
10K
+B
+B
7
8
9
10
11
3
4
1
2
5
6
LG2(231)
CHASIS
GND
1 1
VH-
4
5
6
2
3
7
8
9
10
4
5
6
2
3
7
8
9
10
VL-
GND
VL+
VH+
L
13
14
15
16
17
18
VF2
VF1
–VF
P_IN
UNSW5.6V
+B
AC_RELAY CON
+B
VF2
VF1
–VF
P_IN
UNSW_5.6V
AC_RELAY
4
5
6
7
1
2
3
1 1
2
3
4
5
6
2
3
4
5
6
+B
G
19
20
24
25
26
21
22
23
APRO_GND
AGND
M_GND
D_GND
CD_D_GND
CD_A_GND
TAPE_A_GND
CD_GND
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1 2 3 4
Figure 6-4 SCHEMATIC DIAGRAM (3/10)
6 – 4
5
HEATSINK
LG3(231)
LG1(231)
CHASIS
GND
6
+B
SIGNAL
L902
3µH
R
L901
3µH
L
0
1
LG2(231)
GND
1 1
5
6
7
8
9
10
2
3
4
5
6
7
8
9
10
2
3
4
VH-
VL-
GND
VL+
VH+
1
2
3
4
5
6
1
2
3
4
5
6
+B
LG1(231)
+B
L R
R
L
R942
R943
390 (2W)
D911
DS1SS133
0.2
4.4
+B
+B
+B
+B
–B
D801
D10XB60F
D802
D3SBA60F
47K
R802
D803
RL204F
DZ6.8BSA
ZD802
R805
47 (1/4)
R807
Q801
KTA1274 Y
R808
(1/2W)
(ML)
(ML)
(ML)
C808
0.1
(ML)
(1/2)
R965
C931
10/50
MAIN PWB-A1(2/2)
R949
1K
R950
68K
2
CNP971
1
2
1
CNS971
Q906
KTC3203 Y
M
M971(202-3)
FAN MOTOR
+B M_+13.0V
SP_RLY
R_CH
GND
L_CH
3
4
5
1
2
FW901
JACK PWB-B4
3
4
5
1
2
CNP708
JK701
HEADPHONES
JK953
SUB WOOFER
PRE-OUT
L
R
3
4
1
2
5
1
2
3
4
1
2
3
4
TERMINAL PWB-A3
+
+
–
–
SO901
SPEAKER
TERMINAL
L-CH
R-CH
6 OHMS MIN
L-CH_GND
R-CH_GND
POWER PWB-A2
PT801
C811
0.22
9
10
14
15
8
11
12
13
16
17
TF
150 C
6
7
1
2
3
4
5
D846
DS1SS133
RL841
RELAY
LIFE
NEUTRAL
SUPPLY CODE
(228)
AC120V 60Hz
IC854
R844
82
(1/4W)
AN78L05
VOLTAGE
REGULATOR
3 1
2
+B
+B
D844
D843
0.047 (ML)
9
8
7
6
5
PT841
1
2
3
4
XL-HP505
6 7 11 12 8 9 10
Figure 6-5 SCHEMATIC DIAGRAM (4/10)
6 – 5
XL-HP505
A
B
C
D
AM
LOOP
ANTANNA
2
1
2
1
E
F
G
CHASSIS
GND
FM SIGNAL
AM SIGNAL
D301
DS1SS133
D302
DS1SS133
C323
0.022
AM TRACKING fL
3
4
T303
2
5
6
AM ANT.
1
C330
15P
(CH)
6
4
5
3
AM OSC.
T306
2
1
C335
560P
AM BAND
COVERAGE fL
C334
22P
(CH)
VD301
SVC347S
R323
68K
C331
0.047
C332
0.022
+B
R358
3.9K
24 23 22 2
1 2 3
BAND PASS
FILTER
BF301
1 2 3 1 2
FM FRONTEND
IC301
TA7358AP
3 4 5 6 7 8 9
C304
0.01
C305
4.7P
(CH)
C309
0.001
R314
22
T35
+B
+B
C307
10/16
VD303
SVC230C
T301
FM OSC
4.7P (CH)
C312
0.022
T302
FM IF
+B
R325
47K
R322
680
Q302
KTC3194 Y
R327
0
1
3
2
C318
100P
R316
4.7K
+B
+B
+B
150
C397
0.022
R382
C381
12P (CH)
22 21 20
C394
47/16
C380
10/50
C393 R380
1/50 1.5K
19
C382
15P
(CH) 1 2 3 4 5
IC302
LC72131
PLL(TUNER)
R375
470
C384
0.001
C302
0.001
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1 2 3 4
Figure 6-6 SCHEMATIC DIAGRAM (5/10)
6 – 6
5 6
XL-HP505
TUNER PWB-C
4 23 22 21 20 19 18 17 16 15 14 13
2 3 4 5 6
1 3
T351
AM IF
2
7 8 9 10 11
C356
0.001
12
1/50
+B
+B
R392
270 (1/4W)
Q360
R391
KTA1504 GR
(1/4W)
R383
5.6K
0 19 18 17 16 15 14 13 12
VDD FM
3 4 5 6 7 8 9 10 11
+B
R360
4.7K
+B
7
CNS303
1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 9
CNP303
6-3 12 - C
TO MAIN PWB(2/3)
10
Figure 6-7 SCHEMATIC DIAGRAM (6/10)
6 – 7
11 12
XL-HP505
DISPLAY PWB-B1
A
+B
FL701
NA-11SS55-1
FL DISPLAY
45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8
B
C
D
E
F
G
H
LED PWB-B3
R573
150
LED708
A304BC2H
BI707
1
2
1
2
1
2
Q711
KRA102 S 1
3
2
R772
150
SWITCH PWB-B2
SW728
OPEN/
CLOSE
SW727
DISC 5
SW726
DISC 4
SW725
DISC 3
SW724
DISC 2
SW723
DISC 1
SW722
DIRECT
PLAY
RD19
1K
BI703B
2
1
BI703A
2 KEY
GND
1
TAPE MECHANISM Ass'y(213)
SOLENOID
M
–
+
TAPE
MOTOR
END SW
–COM
+SOL
+MTR
N.C. (OP PACK)
F. REC
R. REC
3
4
5
6
1
2
7
TAPE MECHANISM
PWB Ass'y
FFC702
3
4
5
6
1
2
7
T1 RUN
GND
T_SOL_A
T_MOTOR
FPA
FPB
CNP702
R566
8.2K
R773
4.7K
R774
8.2K
R748
0
R563
R562
R565
R564
10K
10K
10K
10K
+B
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1 2 3 4
Figure 6-8 SCHEMATIC DIAGRAM (7/10)
6 – 8
R737
R736
R761
R747
1K
1K
1K
1K
80
79
81 82 83 84 85 86
S9
S10
VLOAD
87 88
78 S11
77 S12
89 90 91 92 93 94 95 96 9
76 S13
75 S14
74 S15
73 S16
72 S17(DIST 3)
71 S18(DIST 2)
70
69
68
67
S19(DIST 1) IC701
S20(DIST 0) IXA002AW
(Serial No.31000001~402XXXXX
66
65
IXA007AW
(Serial No.402XXXXX)
64
63
IXA020AW
(Serial No.402XXXXX~)
62
61
SYSTEM
MICROCOMPUTER
60
59 MIC_SW
58
57 DIST
56 CLAMP SW
55 DISC SW
54 TRAY SW1
53 TRAY SW2
52
51
50 49
TU
F
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 3
R793
10K
+B
5V BACK UP
CNP706B
6
5
4
3
2
1
+B
Q714 Q715
KRC104 S KRA107 S
2 3 2 3
1 1
LED701
VHP304VT
Q712
KRC104 S
2 3
1
Q713
KRA107 S
3
2
1
+B
Q701
KTA1273 Y
R775
10K
Q702
KTA1271 Y
R776
10K
R780
2.7K
R781
4.7K
1
3
2
5 6
XL-HP505
7 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
R795
1.5
C700
1/50
C701
220/10
88 89 90 91 92 93 94 95 96 97 98 99 100
R701
R702
+B
VDD
–20dBATT
T_BIAS
T_REC/PLAY
1
2
3
4
R700 1K
1K
1K
CD_RESOUT
5
6
IC701
XA002AW
000001~402XXXXX)
CD_WRQ
9
RESET 10
XOUT 11
7
8
XIN 12
VPP 13
XT2 14
XA007AW
No.402XXXXX)
XA020AW
No.402XXXXX~)
CD_DRF
VDD
15
16
CLK
DI
17
18
DO 19
SYSTEM
OCOMPUTER
CE
CD_CE
20
21
CD_CLK
CD_DI
22
23
CD_DO
AVSS
T_RUN
TUN_SM/SPAN
FPA/FPB SW
24
25
26
27
28
PROTECT
VOL_JOG
29
30
R704
R705
R710
R711
R712
R713
R714
R715
R716
R717
R708
1K
1K
1K
C702
0.022
R709
XL700
4.19403MHz
1K
C704
18P(CH)
C703
15P
(CH)
1K
1K
1K
1K
1K
1K
1K
1K
C705
0.022
R721
1K
3 42 41 40 39 38 37 36 35 34 33 32 31
+B
+B
+B
+B
+B
+B
+B UNSW5.6
CNP701A
P_IN
SP_RLY
AC_RLY CON
SP_DET
CLK
DI
DO
CE
21
20
19
+B_PROTECT
D_GND
S_MUTE
T_BIAS
REC/PLAY
–20dB
M_+13V
SW_5V
A_+10V
18
17
16
12
11
10
15
14
13
–VF
VF1
VF2
4
3
2
1
7
6
5
9
8
21
1 FFC701
CNP701B
6-3 12 - F
TO MAIN PWB
R783
10K
+B
R770
10K
2
Q719
KRC104 S
3
1
+B
CNP706B
6
5
4
3
2
1
FFC706
CNP706A
6
5
4
3
2
1
CK UP
R780
2.7K
R781
4.7K
1
3
2
+B
+B
KEY 2
KEY 1
M_+13V
+B
+B
R799
5.6K
R785
10K
R786
10K
+B
R787
10K
KEY 0
R794
10K
L701
100µH
+B
D705
MA111
Q703
KRC102 S
2
1
3
+B
D706
MA111
RX701
GP1UM271
REMOTE
SENSOR
1 2 3
+B
R798
100
C721
47/16
RD17
680
RD18
820
SW719
X-BASS
/DEMO
SW720 SW721
EQUALIZER
MEMORY
/SET
RD08
680
SW709
RD09
820
SW710
RD10
1K
SW711
RD11
1.5K
SW712
CD
RD01
680
SW701
TUNER
(BAND)
RD02
820
SW702
VIDEO
/AUX
RD03
1K
SW703
TAPE
RD04
1.5K
SW704
RD12
2.2K
SW713
RD13
2.7K
SW714
RD14
3.9K
SW715
REC/
PAUSE
TUNING TUNING
/TIME /TIME
UP DOWN
SW705
ON/
STANDBY
CLOCK/
TIMER/
REVERSE REVERSE
MODE PLAY PRESET
DOWN
RD15
5.6K
SW716
STOP
RD16
10K
SW717
PLAY
SW718
PRESET
UP
+5V
GND
PHOTO
TRAY SW2
TRAY SW1
CLAMP
DISC
CD_CE
CD_CLK
CD_D1
CD_D0
CD_DRF
CD_WRQ
CD_RESOUT
14
13
12
11
10
9
8
7
6
5
4
3
2
1
14
1 FFC5
CNP5
6-11 11 - B
TO CD SERVO PWB
6 7 11 12 8 9 10
Figure 6-9 SCHEMATIC DIAGRAM (8/10)
6 – 9
XL-HP505
A
B
C
D
E
F
CD SERVO PWB-D
PICKUP UNIT(306)
F
C
VREF
E
B
A
PD
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
9
TR+
FO+
FO-
TR-
TR+
GND
FO+
TR-
VR
LD
FFC1
GND
LD
VREF
PD
VCC
VR
E
A
B
F
C
GND
TR+
FO-
FO+
TR-
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
9
CNP1
C38
0.01
R6
56K
R3
56K
+B
CD SIGNAL
C1
47/25
C2
0.01
+B
Q1
KTA1504 Y
C4
0.001
R9
10
C3
47/25
C49
0.022
R7
47
+B
+B
R45
100
+B
R41
56K
C37
0.1
VVSS
VVDD
80 79 78 7
C5
0.047
AVDD1
1
2 SLCO
R12
330
C12
100P(CH)
C9
3.3/16
C11
0.056
C8
0.0027
C6
0.01
C46
0.01
C21
0.056
3
4
EFMIN
RF
5
8
5 LPF
JITTC
6
7 AIN
8 CIN
9 BIN
DIN
10
11 FEC
12
PHLPF/RFM
VREF
13
14
EIN
4
15
FIN
TEC
16 1
17
18
TE
TEIN
19
LDD
20
LDS
FDO 21 22 23 2
+B
R19
5.6K
R10
10K
+B
D1
KDS184
R49
10K
36 35 34 33 32 31 30 29 28
FOCUS/TRACKING/
SPIN/SLED DRIVER
IC2
LA6261
27 26 25 24 23 22 21 20 19
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
G
CD MOTOR PWB-E
M1A
SPINDLE
MOTOR
M2A
SLED
MOTOR
SW1A
PICKUP-IN
+
M
M
-
-
+
CNP3A
3
2
1
6
5
4
6
5
4
3
2
1
CNW3
3
2
1
6
5
4
6
5
4
3
2
1
SP+
SP-
SL+
SL-
PUIN
GND
CNP3
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
The numbers 1 to 12 are waveform numbers shown in page 5-1
1 2 3 4
Figure 6-10 SCHEMATIC DIAGRAM (9/10)
6 – 10
+B
+B
Q2
KTA1271 Y
C40
100/10
5 6
C34
C33
C32
C31
C30
C29
C28
C27
100P (CH)
0.022
100P
100P
100P
100P
(CH)
(CH)
(CH)
(CH)
100P (CH)
0.022
R38
R37
R36
R35
R34
R33
R32
+B
1K
1K
1K
1K
1K
1K
1K
7
R53
R21
R54
4.7K
4.7K
4.7K
VVSS
VVDD
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
SLCO
PD02 PD01
EFMIN
RF
LPF
JITTC
5
8
AIN
CIN
BIN
DIN
FEC
PHLPF/RFMON
VREF
EIN
FIN
TEC
TE
TEIN
4
1
LDD
LDS
7
2
6
3
IC1
LC78648E
CD
DIGITAL SIGNAL
PROCESSOR
DO DI
9
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
F16MOUT
OUT1
F16MIN
IOMODE
XVDD
XIN
XOUT
XVSS
RVDD
RCHO
LRVSS
LCHO
48
47
46
45
52
51
50
49
44
43
42
41
56
55
54
53
DVDD
60
59
DATA
58
57
R43
220
12
10
R50
4.7K
11
+B
XL1
16.9344MHz
C52
18P(CH)
C51
18P(CH)
ZD1
DZ3.3BSB
R22
100
FDO 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
C23
10/25
C24
10/25
+B
C25 C26
(ML)
+B
B
1
S184
+B
9
+B
R26
10K
R27
10K
+B
8
R44
1
R42
1
+5V
+8V
+B
XL-HP505
CD RES
WRQ
DRF
DO
DI
CL
CE
DISC
CLAMP
TRAY SW1
TRAY SW2
PHOTO
GND
+5V
CNP5
14
13
12
11
10
9
8
5
4
7
6
3
2
1
14
1
FFC5
CNP704
6-9 11 - E
TO DISPLAY PWB
GND
1
TRAY SW2
2
TRAY SW1
CLAMP
DISC
PHOTO
+5V
TR+
TR-
7
CAM+
CAM-
CNP4
10
11
8
9
5
6
3
4
1
11
FFC4 1
11
1
2
3
4
7
10
11
8
9
5
6
CHANGER PWB-F
SW3
TRAY SW2
SW2
TRAY SW1
SW1
CLAMP
SW4
DISC
+
-
+
-
M
M
RX1
PHOTO
INTERRUPTER
M1
TRAY
MOTOR
M2
MAIN CAM
MOTOR
+B
C18
0.01
C42
0.01
C48
0.022
C50
0.022
+B
+B
+B
R-CH
AGND
L-CH
DGND
DGND
+8V
A_+5V
3
4
5
1
2
6
7
8
CNP2
CNS2
6-2 2 - D
FROM MAIN PWB (1/2)
+B
+B
7 8 9 10
Figure 6-11 SCHEMATIC DIAGRAM (10/10)
6 – 11
11 12
XL-HP505
A
B
C
D
E
F
G
+
SO901
SPEAKER
TERMINAL
–
+ –
COLOR TABLE
BR
RD(R)
OR
YL
GR
BL
VL
GY
WH(W)
BK
PK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
WHITE
BLACK
PINK
M971(202-3)
FAN MOTOR
MAIN PWB-A1
C623
C616
13 14 15 16 17 18 19 20 21 22 23 24
IC601
12 11 10 9 8 7 6 5 4 3 2 1
C619
C617
C613
C615
FROM TUNER PWB
6-19 8 - E
CNS303
R136
R603
R602
R601
14 13 12 11 10 9 8 7
CNP303
6 5 4 3 2 1
R137
C127
RD
BR
2
1
CNS971
TERMINAL PWB-A3
RIGHT LEFT
JK690
VIDEO/AUX
IN
1
2
3
4
Q906 B C E
JK953
SUB WOOFER
PRE-OUT
2
1
R968
C931
1
L903
D911
RL914
C929
5
BI902
R958
R912
Q903
Q904
LG4(231)
L901
18 17 16 15 14 13 12 11 10 9 8 7 6
R913
IC901
ZD902
Q901
R916
R922
Q902
R917
L902
R943
R942
LG2(231)
1 2 3 4
CNS902
H
1 6 2 3 4
Figure 6-12 WIRING SIDE OF P.W.BOARD (1/9)
6 – 12
5
XL-HP505
GY
WH
GR
YL
WH
PK
CNS102
3
4
5
6
1
2
TAPE
MECHANISM Ass'y
6-20 4 - F
136
3 2 1
C127
Q108
C118
C110
13 14 15 16 17 18 19 20 21 22 23 24
IC101
C109
12 11 10 9 8 7 6 5 4 3 2 1
C115
B
C
E
B
Q102
C E
B
C
E
1
R114
GR
C103
YL
WH
E
Q104
C B
PK
R111
BI102
WH
8
C138
L103
B
C
E
C141
Q113 Q114
Q112
C113
C111
R149
9
1
RD
WH
BK
WH
BK
WH
BK
WH
R958
R912
3 12 11 10 9 8 7 6 5 4 3 2 1
3
IC901 ZD903
ZD902
C918
R916 R926
R925
R917
R927
C914
20 21
18 19
7
5
3
1
13
11
9
10
8
6
4
2
14
12
21 FFC701
TO DISPLAY PWB
CNP701A
6-15 11 - G
1
WH
BK
WH
BK
WH
BK
WH
RD
4
3
2
1
6
5
CNS2
8
7
LG3(231)
IC851
6 4 2
7 5 3 1
C874
R930
5
LG1(231)
1
C856
1
11
BL
WH
BL
WH
BL
WH
BL
RD
FW901
TERMINAL PWB-A3
7
1
WH
GR
BL
WH
GR
RD
BL
WH
GR
BL
GR
WH
GR
WH
GR
RD
CNS802
4
3
2
1
6
5
8
7
6
5
4
3
10
9
2
1
CNS801
1
5
3
4
1
2
5
JACK PWB-B4
JK701
HEADPHONES
7 12 8 9 10
Figure 6-13 WIRING SIDE OF P.W.BOARD (2/9)
6 – 13
11
XL-HP505
A
B
C
D
E
F
G
SW728
OPEN/
CROSE
SWITCH PWB-B2
RD25
SW726
DISC 4
RD24
RD23
SW724
DISC 2
SW723
DISC 1
RD20
RD19
RD22
RD21
1
2
SW722
CD DIRECT
PLAY
CNP5
6-17 9 - G
TO CD SERVO PWB
FFC5 14
1
COLOR TABLE
BR
RD(R)
OR
YL
GR
BL
VL
GY
WH(W)
BK
PK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
WHITE
BLACK
PINK
1
7
FFC706
2
REMOTE SENSOR
1
RX701
2 3
9
11
13
5
7
1
3
10
12
14
6
8
2
4
C720
R708
R783
R710
R717
R716
R714
R711
R715
R701
R702
R700
R712
R713
2
4
6
1
3
5
7
R720
R790
R755
Q719
RD18
RD17
SW720
EQUALIZER
SW719
PRESET
X-BASS
/DEMO
UP
R770
MEMORRY
/SET
R799
R566
SW717
PLAY
R774
R773
SW718
RD16
RD15
Q701 R732
B
C
E
D712
SW713
RD11
REC/PAUSE
E
C
B
R731
Q715
D711
R776
RD13
RD14
RD12
SW714 TUNING/
TIME
UP
SW712
TAPE
SW716
STOP
CNP702
1
2
3
4
5
6
7
SW715 TUNING/
TIME
DOWN
SW711 VIDEO/
AUX
C702
R796
RD09
FL702
FL DISPLAY
D705
100
XL700
1
VR701
R781
Q703
R7
R7
1 7
FFC702
DISP
TO TAPE MECHANISM PWB
6-20 4 - C
H
1 6 2 3 4
Figure 6-14 WIRING SIDE OF P.W.BOARD (3/9)
6 – 14
5
XL-HP505
LED PWB-B3
1
7
R573
1
BI707
2
LED708
1 2
CNS707
FL702
FL DISPLAY 81 80
2
100
1
5
95
10
90
85
75
70
65
IC701
15
20
40
25 35
60
55
45
XL700
R721
R789
R727
R779
R785
R786
C705
R718
30 31
R729
R723
R724
R725
R728
R787
R784
51
50
R736
R747
R737
R761
R734
R771
R782
R730
Q711
CNP707
R772
1
2
R746
R794
R735
D705
VR701
R780
C717
R781
Q703
D708
1 3 2
D706
C718 D707
D709
C719
R797
SW710
TUNER
(BAND)
SW709
CD
DISPLAY PWB-B1
7
R763
R795
R748
5
7
1
3
2
4
6
R564
R562
R563
R565
SW705
PRESET
DOWN
ON/
STAND-BY
RD04
SW702
SW704
REVERSE
RD03
RD02
CLOCK/
TIMER
CNP701A
REVERSE
MODE
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
21
FFC701
CNP701B
6-13 11 - B
TO MAIN PWB
1
11 8 9 10
Figure 6-15 WIRING SIDE OF P.W.BOARD (4/9)
6 – 15
12
XL-HP505
A
B
CNP3A
4
5
6
1
2
3
SW1A
PICKUP IN
M2A
SLED MOTOR
CD MOTOR PWB-E
1
1
2
3
4
5
6
7
8
9 11
10
13
12
15
14 16
16
C
D
E
F
-
M2
MAIN CAM
MOTOR
+
M1A
SPINDLE MOTOR
M1
TRAY
MOTOR
-
+
11
10
9
8
7
6
5
4
3
2
1
CNB1
4
3
2
1
6
5
CHANGER PWB-F
WH
GR
WH
GR
WH
RD
CNW3
1
11
FFC4
G
H
SW4
DISC
SW3
TRAY SW2
SW1
CLAMP
SW2
TRAY SW1
RX1
PHOTO
INTERRUPTER
The numbers 1 to 12 are waveform numbers shown in page 5-1
1 2 3 4
Figure 6-16 WIRING SIDE OF P.W.BOARD (5/9)
6 – 16
5
COLOR TABLE
BR
RD(R)
OR
YL
GR
BL
VL
GY
WH(W)
BK
PK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
WHITE
BLACK
PINK
6
4
3
2
1
6
5
CD P
XL-HP505
BLE
OWN
ED
ANGE
LOW
EEN
UE
LET
RAY
HITE
ACK
NK
4
3
2
1
6
5
CD PICKUP UNIT(307)
2
1
WAVEFORM NUMBERS
4
5
1 80
8
7
3
6
20
21
9
15
10
5
25
IC1
30
35
75
70
65
55
50
45
40 41
61
60
12
10 11
1
FFC1
16
1
11
CNP3
4
3
6
5
2
1
CNP4
6
8
2
4
10
9
11
5
7
1
3
C40
R44
R45
1
18
Q2
36
35
5
30
IC2
10
25
15
20
19
R19
R17
E C B
D1
C39
R10
R49
R8
R16
R15
R14
R13
R18
R28
R47
R20
C3
R9
C4
C46
Q1
C14
20
21
C48
1
2
3
4
5
6
7
8
9 11
10
CNP1
12
13
14
15
16
R12
C1
C38
C2
C35
C36
R57
C37
C5
C49
R7
R39
R40
R41
C27
C34
1 80
15
10
5
25
L1
75
70
IC1
30
35 45
50
65
55
40 41
C22
R26 C44
R24
R27
R54
R25
61
60
C30
C29
R58
R50
XL1
R51
C51
R30
R53
R21
R31
R38
C33
R37
C32
C31
R36
R35
R34
R33
C28
R32
R56
C42
R55
14
13
12
11
CNP5
10
9
8
7
6
5
4
3
2
1
8 7 6 5
R22
4 3 2 1
CNP2
CD SERVO PWB-D
14
FFC5
CNP704
6-14 3 - D
TO DISPLAY PWB
1
CNS2
6-13 12 - D
FROM MAIN PWB
7 8 9 10
Figure 6-17 WIRING SIDE OF P.W.BOARD (6/9)
6 – 17
11 12
XL-HP505
POWER PWB-A2
D846 A
B
C
D
E
F
G
H
1
BK
WH
TRANSFORMER (SUB)
F805
4A 125V R890
1 2 3 4 5 6 7
AC POWER
SUPPLY CORD
AC 120 V, 60 Hz
TRANSFORMER (MAIN)
17 16 15 14 13 12 11 10 9 8
C811
C809
C808
C810
C803
B C E
ZD803
R808
Q801
R807
C801
1 2
CNP801
3 4 5 6
F801
4A 125V
CNS801
7
6-13 12 - G
4A 125V
8
F802
FROM MAIN PWB
9 10
R842
C843
Q841
E C B
R843
D842
D843
D844
D845
C841
D856
1 2 3
D853
R841
CNP802
1 2 3 4 5 6
C861
COLOR TABLE
BR
RD(R)
OR
YL
GR
BL
VL
GY
WH(W)
BK
PK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
WHITE
BLACK
PINK
CNS802
FROM MAIN PWB
6-13 12 - F
2 3 4
Figure 6-18 WIRING SIDE OF P.W.BOARD (7/9)
6 – 18
5 6
SO302
GND
FM ANNTENNA
TERMINAL
FM
75 OHMS
AM LOOP
ANNTENNA
CNP301
2 1
TUNER PWB-C
CHASSIS
GND
CNP303
6-12 6 - C
TO MAIN PWB
C331
T303
AM TRACKING fL
R323
C334
T306
AM BAND
COVERAGE fL
10
9
8
7
14
13
12
11
4
3
2
1
6
5
C364
C365
C342
C363
C316
C368
C361
R358
BF301
1 2 3
C305
1 2 3
IC301
C343
4 5 6 7 8 9 C307
C315
R314
FM RF
L312
C308
D305
24
23
22
21
20
19
18
17
16
15
14
13
R351
1
2
3
1
10
11
12
7
8
9
2
3
4
5
6
T302 FM IF
R309
C320
VD303
B
C
E
TP301
C393
C389
C318
T301
22
17
16
15
14
13
21
20
19
18
12
1
CF352
2 3
T351
Q360
R360
C386
R376 R388
C391
R384
R385
C383
R386
1
2
3
4
5
6
7
8
9
10
11
R387
C398
C396
X351
X352
C370
C388
XL-HP505
7 8 9 10
Figure 6-19 WIRING SIDE OF P.W.BOARD (8/9)
6 – 19
11 12
XL-HP505
F
B
A
TAPE MECHANISM Ass'y(213)
TO DISPLAY PWB
6-14 4 - G
CNP702
1
FFC702
7
1 7
C
RD BK
SOLENOID
TAPE MECHANISM
PWB Ass'y
D
TAPE MOTOR
E
RECORD/PLAYBACK/ERASE HEAD
HEAD PLATE
BLOCK
6 1
G
H
COLOR TABLE
BR
RD(R)
OR
YL
GR
BL
VL
GY
WH(W)
BK
PK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
WHITE
BLACK
PINK
1
CNS102
6-13 10 - A
FROM MAIN PWB
2 3 4
Figure 6-20 WIRING SIDE OF P.W.BOARD (9/9)
6 – 20
5 6
XL-HP505
CHAPTER 7. FLOWCHART
[1] TROUBLESHOOTING
1. When the CD does not function
The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and check the playback operation.
When this section does not operate even after the above step is taken, check the following items.
Remove the cabinet and follow the trouble shooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
1.
CD optical pickup Lens cleaner disc
Parts code
UDSKA0004AFZZ
HOW TO USE
1.
Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it.
2.
Place the CD cleaner disc onto the CD disc tray with the brush side down,then press the play button.
3.
You will hear music for about 20 seconds and the CD player will automatically stop.
If it still play continuously, press the stop button.
Cleaning fluid
CAUTION
The CD lens cleaner should be effective for 30-50 operations, however if the brushes become worn out earlier then please replace the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth.
Do not drink the cleaner fluid or allow it contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice.
The CD cleaner disc must not be used on car CD players or on computer CD-ROM drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law.
Cleaner disc
2. When a CD cannot be played
2.1. "E-CD01" is displayed.
1) Check the power to IC1 (LC78648E), the presence of the clock signal (16.9344 MHz) and the status of the RESET terminal (pin 67 on IC1).
2) Does the pickup move to the PICKUP-IN Switch (SW1A) position ?
If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP).
2.2. Pressing the CD operation key is accepted, but playback does not occur.
1) Focus-HF system check
2) Tracking system check
3) Spin system check
4) PLL system check
5) Others
7 – 1
XL-HP505
(1) Focus-HF system check.
Although a CD is inserted and the cover is closed, "NO
DISC" is displayed.
Press the Tray1 CD Eject Button without inserting a disc, and try starting the playback operation.
T
Stopped
CH1=500 mV
DC 10:1
1
FDO
CH3=500 mV
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
1. Does the pickup move to the PICKUP-IN Switch (SW1A) position ?
Yes
2. Does the focus (lens) move up and down ?
(Waveform drawing Figure 1)
No
No
3
TDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.000 V
CH2 :
CH3 :
CH4 :
0.0 V
0.000 V
0.00 V
=Record Length=
Main : 100 K
Zoom : 2 K
CH1 v/DIV
500 mV
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay : 0.0 ns
Hold off : 0.2 µs
Figure 1
Sled motor (M2A).
Check the focus peripheral circuit.
Yes
3. Is the laser lit ?
No Check the laser diode driver Q1 peripheral circuit.
4. Is the turntable rotating ?
Yes
When a disc is loaded, start playback operation.
No Spindle motor (M1A).
1. Is focus servo activated ?
(Waveform drawing Figure 2)
Yes
2. Does DRF change from "L" to "H" ?
No Pins 7~11, 79 and 80 on IC1
Check the laser diode driver Q1 peripheral circuit.
3. Is the HF waveform normal ?
(Waveform drawing Figure 3)
Yes
Stopped
CH1=500 mV
DC 10:1
CH2=10 V
DC 10:1
CH3=1 V
DC 10:1
1
FDO
T
2
DRF
500 ms/div
(500 ms/div)
NORM:20 kS/s
3
TE
CH Position To
-3 div
=Filter=
-1 div
Smoothing : ON
BW : FULL
CH1 :
CH2 :
0 div
=Offset=
0.000 V
0.0 V
CH3 :
CH4 :
0.00 V
0.00 V
+1 div +3 div
=Record Length=
Main : 100 K
Zoom : 2 K
CH2
Position
0.20 div
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
Hold off :
0.0 ns
0.2 µs
Figure 2
No Is the disc rotating ?
No
No Check the spin system.
If the level is not normal.
If the disc is spinning and a HF waveform is generated, DRF will go H.
Figure 3
Vp-p=1.0 V~1.3 V
0.5 mV/div,0.5 µsec/div
7 – 2
XL-HP505
(2) Focus-HF system check.
Check the TE waveform at pin 17 on IC1.
If the waveform shown in Figure 4 appears and soon after NO
DISC appears ?
No
"Initialization" is possible, but play is not possible ?
Yes
The tracking servo is not activated.
Check the peripheral circuits at pins 16, 17 and 22 on IC1, and
FFC1.
Yes
A normal jump operation cannot be completed or the beginning of the track cannot be found.
Check the around pin 22 on IC1.
"Initialization" is not possible.
No
Data cannot be read. Check the VCO-PLL (Pin76~80 on IC1) system.
Stopped
CH1=10 V
DC 10:1
T
CH2=1 V
DC 10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
2
TE
T
1
DRF
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
CH2 :
0.0 V
0.00 V
CH3 :
CH4 :
0.00 V
0.00 V
=Record Length=
Main :
Zoom :
100 K
2 K
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
Hold off :
2.924 ms
0.2 µs
Figure 4
(3) Spin system check.
Press the OPEN/CLOSE switch without inserting a disc, and then try starting the play operation.
1. The turntable rotates a little ?
(Waveform drawing Figure 5)
2. The turntable doesn't rotate.
No
Yes
The spin driver circuit is OK.
Check around pin 24 on IC1, pins 3 and 4 on IC2, and CNW3.
Stopped
CH1=200 mV
DC 10:1
T
CH2=500 mV
DC 10:1
1999/04/07 09:51:15
500 ms/div
(500 ms/div)
NORM:20 kS/s
T
2
FDO
1
SPDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.000 V
CH2 :
CH3 :
CH4 :
0.000 V
0.00 V
0.00 V
=Record Length=
Main : 100 K
Zoom : 2 K
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay :
Hold off :
2.924 ms
0.2 µs
Figure 5
7 – 3
XL-HP505
(4) PLL system check.
When a disc is loaded, start play operation.
Stopped
CH1=500 mV
DC 10:1
3
PDO1
CH3=1 V
DC 10:1
1999/04/05 17:33:17
CH4=1 V
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
The HF waveform is normal, but the TOC data cannot be read.
Check the PDO waveform. (Figure 6)
Check around pins 73~78 on IC1.
4
PDO2
T
1
FDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.000 V
CH2 :
CH3 :
CH4 :
0.0 V
0.00 V
0.00 V
=Record Length=
Main : 100 K
Zoom : 2 K
CH1 v/DIV
500 mV
=Trigger=
Mode : AUTO
Type : EDGE CH2
Delay : 0.0 ns
Hold off : 0.2 µs
Figure 6
(5) Others.
The HF waveform is normal and the time is displayed normally, but no sound is produced. Or the sound has dropouts.
Is pin 52 (C2F) on IC1 "L" ?
No There are too many error flags on a damaged disc which makes error correction impossible.
Yes
1. When playing at normal speed.
Check the peripheral circuit at pin 39 (DOUT) on IC1 and the waveform (Figure 7).
Check again using a known good disc.
If OK, Check the unit.
T
Stopped
CH1=2 V
DC 10:1
T
1999/04/07 09:25:28
500 ns/div
(500 ns/div)
NORM:200 MS/s
1
DOUT
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 : 0.00 V
CH2 :
CH3 :
CH4 :
0.00 V
0.00 V
0.00 V
=Record Length=
Main : 1 K
Zoom : 100
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay : 2.887 ms
Hold off : 0.2 µs
Figure 7
7 – 4
XL-HP505
CHAPTER 8. OTHERS
[1] FUNCTION TABLE OF IC
IC1 VHiLC78648E-1: CD Digital Signal Processor (LC78648E) (1/2)
24
25
26
27
28*
29*
20
21
22
23
16
17
18
19
12*
13
14
15
8
9
10
11
38*
39*
40
41
42
43
6
7
4
5
2
3
Pin No.
Terminal Name Input/Output Setting in Reset
1 AVDD1 Output —
SLCO
EFMIN
Output
Input
—
—
RF
LPF
JITTC
AIN
Output
Output
Input
Input
—
—
—
—
30*
31*
32*
33*
34
35
36
37*
CIN
BIN
DIN
FEC
PHLPF/RFMON
VREF
EIN
FIN
TEC
TE
TEIN
LDD
LDS
FDO
TDO
SLDO
SPDO
AVSS2
AVDD2
DVDD
DVSS
VPB
DEFECT
FSEQ
EFLG
FSX
CONT1
CONT2
CONT3
MONI1
MONI2
DOUT
TEST
LVDD
LCHO
LRVSS
Input
Input
Input
Output
Output
Output
Input
Input
Output
Output
Input
Output
Input
Output
Output
Output
Output
—
—
—
—
Output
Output
Output
Output
Output
Input/Output
Input/Output
Input/Output
Input/Output
Output
Output
Input
—
Output
—
—
—
—
ZHI
AVDD1/2
—
—
—
—
—
ADAVDD/2
ADAVDD/2
ADAVDD/2
ADAVDD/2
—
—
—
—
H
L
L
L
L
Input
Input
Input
Input
L
L
L
—
LVDD/2
—
Function
Analog power supply pin 1.
slice level control.
Slice level Control output pin.
RF signal input pin.
RF signal Output pin.
RF signal DC level detection LPF capacitor connection pin.
Jitter detection capacitor connection pin.
A signal input pin.
C signal input pin.
B signal input pin.
D signal input pin.
FE signal LPF capacitor connection pin.
Reference supply setting terminal.
VREF voltage output pin.
E signal input pin.
F signal input pin.
TE signal LPF capacitor connection pin.
TE signal output pin.
TES signal generation TE signal input pin
Laser power control signal output pin.
Laser power control signal input pin.
Focus control output pin. D/A output.
Tracking control output pin. D/A output.
Thread control output pin. D/A output.
Spindle control output pin. D/A output.
Analog GND pin 2. Must always be connected to 0V.
Analog power supply pin 2.
Digital power supply pin.
Digital GND pin 2. Must always be connected to 0V.
Rough servo/phase control automatic switching monitor output pin.“H” for rough servo and “L” for phase servo.
Defect signal output pin.
Synchronization signal detection output pin.
Outputs a high level when the Synchronization signal detection from the EFM signal and the internally generated Synchronization signal agree.
C1, C2 error correction monitor pin
7.35kHz Synchronization signal output pin.
CLV playback mode.
General purpose I/O pin 1.
General purpose I/O pin 2.
Controlled by command from the microprocessor. Any of these that are unused must be either set up as input pin ports and connected to 0V, or set up as output pin ports and left open.
General purpose I/O pin 3.
External deiemphasis setting pin, INternal signal monitor pin 1.Controlled by microprocessor.
Internal signal monitor pin 2.
Digital OUT output Pin. (EIAJ format)
Test input pin. Must always be connected to 0V.
Left channel
D/A converter
L channel Power supply pin.
L channel output supply pin.
LR channel GND pin. Must always be connected to 0V.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
8 – 1
XL-HP505
IC1 VHiLC78648E-1: CD Digital Signal Processor (LC78648E) (2/2)
Pin No.
Terminal Name Input/Output Setting in Reset
44
45
46
47
48
49
50
RCHO
RVDD
XVSS
XOUT
XIN
XVDD
IOMODE
Output
—
—
Output
Input
—
Input
RVDD /2
—
—
Oscillator
Oscillator
—
—
Right channel
D/A converter
Function
R channel Power supply pin.
R channel output supply pin.
Digital GND pin. Must always be connected to 0V
Crystal oscillator
Power supply for crystal oscillator.
Connected for a 16.9344 MHz crystal oscillator pin.
Digital power supply pin. Must always be connected to 0V
CONT4 to 6.MONI3~5, DRF, WRQB pin output mode switching input pin.
”L” setting: Normal output “H” setting: Nch open drain output
DF. DAC external clock input pin.
General-purpose output pin 1.
16.9344 MHz output port.
51
52*
53*
54
55
56
60
61
62
63
57
58
59
64
65
66
67
68
69
70
71*
72*
73*
74
75
76
77
78
79
80
F16MIN
OUT1
16MOUT
ASLRCK
ASDACK
ASDFIN
LRSK
DATACK
DATA
DVDD
DVSS
CE
CL
DI
DO
WRQB
RESB
DRF
C2F/SBCK
CONT6/SBCK
MONI5
MONI4
MONI3
CONT5
CONT4
PDO1
PDO2
PCKIST
VVSS
VVDD
Input
Output
Output
Input
Input
Input
Output
Output
Output
—
—
Input
Input
Input
Output
Output
Input
Output
Input/Output
Input/Output
Output
Output
Output
Input/Output
Input/Output
Output
Output
Input
—
—
—
L
CLK
Output
—
—
—
L
L
L
—
—
—
—
—
(H)
L
—
L
Input
Input
L
L
L
Input
Input
—
—
—
—
—
Anti-shock
Left/Right clock input pin.
(Must be connect to 0 V when unused.)
Bit clock input pin.
(Must be connect to 0 V when unused.)
Left/Right channel data input pin.
(Must be connect to 0 V when unused.)
Left/Right channel data output pin.
Digital data output
Bit clock output pin.
Left/Right clock output pin.
Digital power supply pin.
Digital GND pin 2. Must always be connected to 0V.
Microcomputer
Interface
Chip enable signal input pin.
Data transfer clock input pin.
Data output pin.
Data output pin. (Try state output.)
Interruption signal output pin.
Reset input pin for LSI.
This pin must be set LOW briefly after power is first applied.
Focus ON detection pin.
Error flag monitor pin, or sub code read clock input pin.
General-purpose I/O pin 6, or sub code read clock input pin.
Controlled by commands from the microprocessor.
Controlled by commands from the microprocessor.
Any of these that are unused must be either set up as input pin ports and connected to
0V, or set up as output pin ports and left open.
Internal signal monitor pin 5.
Internal signal monitor pin 4.
Internal signal monitor pin 3.
General purpose I/O pin 5.
General purpose I/O pin 4.
Controlled by command from the microprocessor. Any of these that are unused must be either set up as input pin ports and connected to 0V, or set up as output pin ports and left open when unused.
PLL
Phase comparison output pin 1 to control built-in VCO.
Phase comparison output pin 2 to control built-in VCO.
Resistor connection pin to set current for PDO1 and 02 outputs.
Built-in VCO GND pin. Must always be connected to 0V.
Built-in VCO power supply pin.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
The same potential must be supplied to all power supply pins, i, e., AVDD1, AVDD2, XVDD, DVDD, LVDD and RVDD)
8 – 2
IC1 VHiLC78648E-1: CD Digital Signal Processor(LC78648E)
BIN
DIN
FEC
PHLPF/RFMON
VREF
EIN
FIN
TEC
AVDD1
SLCO
EFMIN
RF
LPF
JITTC
AIN
CIN
TE
TEIN
LDD
LDS
6
7
4
5
8
9
10
11
1
2
3
16
17
18
19
20
12
13
14
15
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
LC78648E
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
60
59
58
45
44
43
42
41
49
48
47
46
57
56
55
54
53
52
51
50
OUT1
F16MIN
IOMODE
XVDD
XIN
XOUT
XVSS
RVDD
DVDD
DATA
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
F16MOUT
RCHO
LRVSS
LCHO
LVDD
XL-HP505
JITTC
SLCO
EFMIN
PDO1
PDO2
PCKIST
VVDD
VVSS
XVDD
XVSS
XIN
XOUT
F16MIN
F16MOUT
ASLRCK
ASDACK
ASDFIN
RVDD
RCHO
LRVSS
LCHO
LVDD
RESB
TEST
IOMODE
PHLPF/RFMON
VREF
LDD
LDS
LPF
RF
AIN
CIN
BIN
DIN
FEC
EIN
FIN
TEC
TE
TEIN
MONITOR
VREF
APC
RF SIGNAL
PROCESSOR
FOCUS ERROR
PROCESSOR
TRACKING ERROR
PROCESSOR
JITTER/DETECT
SLICE LEVEL
CONTROL
PLL
CLOCK
GENERATOR
RAM
EXTERNAL
AUDIO IN
LPF
A/D
AUTO
ADJUST
TRACK
JUMP
CLV
CAV
CONTROL
ERROR
CORRECTION
INTERPOLATION
MUTE
ATTENUATION
8FS DIGITAL
FILTER
DEEMPHASIS
1bit DAC
SETVO
PROCESSEROR
A/D
RAM
RUPTURE
DEFECT
DRF
CPU I/F
PORT
FRAME SYNC
DETECT,PROTECT,
INSERT,
EFMDECODE
MONITOR SIGNAL
SELECTOR
SUBCODE DECODE
CRC & TEXT
AUDIO OUT
SERIAL
OUT
Figure 1 BLOCK DIAGRAM OF IC
8 – 3
DOUT
LRSY
DATACK
DATA
DVDD
DVDD
DVSS
DVSS
FDO
TDO
SPDO
SLDO
AVDD1
AVSS
AVDD2
DEFECT
DRF
VPB
CL
CE
DI
DO
WRQB
CONT1~6
OUT1
FSEQ
FSX
EFLG
C2F
MONI1~5
XL-HP505
IC2 VHILA6261//-1: Focus/Tracking/Spin/Sled Driver (LA6261)
28
29
30
31
24
25
26
27
32
33
34
35
36
20
21
22
23
16*
17
18
19
12*
13
14*
15
8
9
10
11
6
7
4
5
2
3
Pin No.
Terminal Name
1 VO3+
VO3-
VO2+
VO2-
VO1+
VO1-
PGND1
REGIN
PVCC1
REGOUT
VIN1
VIN1G
VIN2
VIN2G
VIN3
VIN3G
VIN4
VIN4G
FWD5
REV5
VCONT5
FWD6
REV6
VCONT6
VREFIN
SGND
SVCC
PVCC2
MUTE
PGND2
VO6+
VO6-
VO5+
VO5-
VO4+
VO4-
Function
BTL Output pin (+) for channel 3.
BTL Output pin (-) for channel 3.
BTL Output pin (+) for channel 2.
BTL Output pin (-) for channel 2.
BTL Output pin (+) for channel 1.
BTL Output pin (-) for channel 1.
Power GND for channels 1,2,3 and 4 (BTL).
Regulator pin (External PNP base).
Power for channels 1,2,3 and 4 (BTL). (SVCC short-crircuited)
Regulator pin (External PNP collector).
Input pin for channel 1
Input pin for channel 1 (for gain control)
Input pin for channel 2
Input pin for channel 2 (for gain control)
Input pin for channel 3
Input pin for channel 3 (for gain control)
Input pin for channel 4
Input pin for channel 4 (for gain control)
CH5 Output change pin (FWD). Logic input for bridge.
CH5 Output change pin (REV). Logic input for bridge.
Input pin for CH5 output voltage control
CH6 Output change pin (FWD). Logic input for bridge.
CH6 Output change pin (REV). Logic input for bridge.
Input pin for CH5 output voltage control.
Reference voltage input pin.
Signal system GND
Signal system power (PVCC1 short - circuited)
Power for channel 5 and 6 (H bridge).
Input pin for BTL mute.
Power GND for channels 5 and 6 (H bridge).
H bridge Output pin (+) for channel 6.
H bridge Output pin (-) for channel 6.
H bridge Output pin (+) for channel 5.
H bridge Output pin (-) for channel 5.
BTL Output pin (+) for channel 4.
BTL Output pin (-) for channel 4.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
* Set power system GND to the minimum potential together with SGND
* Short-circuit three pins of power system SVSS and PVCC1 externally before use.
8 – 4
IC2 VHILA6261//-1: Focus/Tracking/Spin/Sled Driver (LA6261)
7
8
5
6
9
3
4
1
2
CH3
CH2
-
+
-
+
-
+
CH1
-
+
-
+
-
+
VOLTAGE
CONTROL AMP
10
11k
11
12
1k
11k
13
14
1k
11k
15
16
17
1k
11k
18
1k
22k
-
+
22k
-
+
22k
-
+
22k
-
+
BTL
DUFFER AMP
For 1/2 VCC
Bandgad
Refcronce voltage
TSD
XL-HP505
+
-
+
-
CH4
CH5
36
35
30
29
28
34
33
32
31
CH6
-
+
DUFFER AMP
For VREF
23
22
21
20
19
27
26
25
24
Figure 2 BLOCK DIAGRAM OF IC
8 – 5
XL-HP505
IC601 VHiLC75341/-1: Audio Processor (LC75341)
3
4
Pin No.
Terminal Name
1 DI
2
5
6
7
8
9-12
CE
VSS
LOUT
LBASS
LTRE
LIN
LSEL0
L4-1
Function
Serial data and clock input pin for control.
Chip enable pin.
Data written into an internal latch in a timing of "H" to "L".
Each analog switch is activated.
Data transfer enabled at "H" level.
Ground pin.
Bass band filter comprising capacitor and resistor connection pin and bass/treble output pin.
Bass band filter comprising capacitor and resistor connection pin.
Treble band filter comprising capacitor and resistor connection pin.
Volume + equaliser output pin.
Input selector output pin.
Input signal pin.
IC601 VHiLC75341/-1: Audio Processor (LC75341)
Pin No.
Terminal Name
13-16 R1-4
17
18
19
RSEL0
RIN
RTRE
20
21
22
23
24
RBASS
ROUT
VREF
VDD
CLK
Function
Input signal pin.
Input selector output pin.
Volume + equaliser output pin
Treble band filter comprising capacitor and resistor connection pin.
Bass band filter comprising capacitor and resistor connection pin.
Bass band filter comprising capacitor and resistor connection pin and bass/ treble output pin.
0.5x VDD voltage generation block for analog ground. Capacitor of several 10µF to be connected between
VREF and AWSS (VSS) as a countermeasure against power ripple.
Supply pin
Serial data and clock input pin for control.
8 7 6 5 4
L4
9
CD
L3
10
Tuner
L2
11
Tape
L1
12
Video
R1
13
R2
14
R3
15
R4
16
CONTROL
CIRCUIT
CONTROL
CIRCUIT
CONTROL
CIRCUIT
LVref
CCB
INTERFACE
RVref
3
2
1
24
23
22
VSS
CE
DI
CLK
VDD
VREF
17 18 19 20 21
Figure 3 BLOCK DIAGRAM OF IC
8 – 6
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW)(Serial NO.310000001~402XXXXX) (1/2)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial NO.402XXXXX)(1/2)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW)(Serial NO.402XXXXX ~) (1/2)
VDD
P27
P26
P25
P24
P23
P22
P21
P20
AVSS
ANI7
ANI6
ANI5
ANI4
ANI3
ANI2-ANI0
Port Name
VDD
P37
P36
P35
P34
P33
P32
P31
P30
RESET
X2
X1
IC(VPP)
XT2
P04
P73
P72
P71
P70
VDD
P127
P126
P125
AVDD
AVREF
INTP3
P02
INTP1
INTP0
VSS
P74
P124
P123
P122
P121
24
25
26
27
28
29
30
31-33
20
21
22
23
16
17
18
19
12
13
14*
15
8*
9*
10
11
6
7
4
5*
2
3
Pin No.
1
46
47
48
49*
42
43
44
45
50*
51*
52*
53
38
39
40
41
34
35
36
37
Terminal Name Input/Output
VDD Input
-20dBATT
T BIAS
Output
Output
T_REC/PLAY
NO USE
CD RESOUT
CD_WRQ
NO USE
NO USE
RESET
XOUT
XIN
VPP
NO USE
CD_DRF
VDD
CLK
DI
DO
CE
CD CE
CD CLK
CD DI
CD DO
AVSS
T RUN PULS
TUN SM/SPAN
T_FP SW
PROTECT
VOL JOG
KEY 2-KEY 0
AVDD
AVREF
P_IN
PHOTO
SP DET
REMOCON
VSS
S MUTE
TIMER LED
T_SOL
T_MOTOR
VOL LED
VDD
SP RLY
AC RLY
RDS RST
RDS READY
RDS RDDA
RDS RDCL
TRAY SW2
Output
Output
Output
Input
Output
Output
Input
Output
Input
—
—
Input
Input
Output
Output
Input
Output
Output
Output
Output
Input
—
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
—
Output
Output
Output
Output
Output
Input
Output
Output
Output
Input
Input
Output
Input
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
(+) Power supply 5V.
-20dB Attenuator.
Tape record bias control.
Tape REC/PLAY control.
Open.
CD reset.
CD WRQ input.
Open.
Open.
Reset Input.
Main clock output 4.19MHz.
Main clock input 4.19MHz.
GND
Open
CD DRF detect.
(+) Power supply 5V.
CD clock.
Data output.
Data input.
CE output.
CD chip enable.
CD Clock.
CD Data output.
CD Data input.
Analog ground.
Tape Run Pulse detect.
Tuner signal meter/Span Selecetor.
Tape Fool Proof A & B SW.
Power abnormal detect.
Volume jog input.
Key input.
Function
Analog power supply 5V.
Analog reference voltage 5V.
Power failure detect.
5-Changer Photo SW.
Speaker abnormal detect.
Remocon input.
Ground voltage.
System mute control.
Timer LED control.
Tape solenoid control.
Tape motor control.
Volume control.
(+) Power supply 5V.
Speaker relay control.
AC relay control.
RDS reset.
RDS ready.
RDS data.
RDS clock.
5-Changer Tray SW2.
XL-HP505
8 – 7
XL-HP505
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW)(Serial NO.310000001~402XXXXX) (2/2)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial NO.402XXXXX)(2/2)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW)(Serial NO.402XXXXX~) (2/2)
65*
66*
67*
68*
61*
62*
63*
64*
57
58*
59
60*
Pin No.
54
55
56
69
70
71
72
P101/FIP30
P100/FIP29
P97/FIP28
P96/FIP27
73-78
79
FIP26-FIP21
VLOAD
80-89 FIP20-FIP11
90-100 FIP10-FIP0
P111
P110
P107
P106
P105
P104
P103
P102
Port Name
P120
P117
P116
P115
P114
P113
P112
Terminal Name Input/Output
TRAY SW1 Input
DISC SW
CLAMP SW
Input
Input
DIST
ILLU LED
MIC SW
KARA_LATCH
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
S20/DEST0
S19/DEST1
S18/DEST2
S17/DEST3
S16-S11
VLOAD
S10-S1
G11-G1
Input
Output
Input
Output
Output
Output
Output
Output
Output
Output
Output
Output
Input
Output
Output
Output
Output
Input
Output
Output
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
Function
Open.
Open.
Open.
Open.
Open.
Open.
Open.
Open.
5-Changer Tray SW1.
5-Changer Disc SW1.
5-Changer Clamp SW1.
Destination input.
Illumination LED.
Mic sw detect.
Karaoke latch.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver.
VLOAD -35V
FL segment driver.
FL grid driver.
8 – 8
XL-HP505
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW)(Serial NO.310000001~402XXXXX)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial NO.402XXXXX)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW)(Serial NO.402XXXXX~)
VDD
-20dBATT
T_BIAS
T_REC/PLAY
CD_RESOUT
CD_WRQ
RESET
XOUT
XIN
VPP
CD_DRF
VDD
CLK
DI
DO
CE
CD_CE
CD_CLK
CD_DI
CD_DO
AVSS
T_RUN PULS
TUN_SM
(SPAN)
T_FP SW
PROTECT
VOL_JOG
VDD
P37
P36/BUZ
P35/PCL
P34/T12
P33/T11
P32/TO2
P31/TO1
P30/TO0
RESET
X2
X1
IC(VPP)
XT2
P04/XT1
VDD
P27/SCK0
P26/SO0/SB1
P25/SI0/SB0
P24/BUSY
P23/STB
P22/SCK1
P21/SO1
P20/SI1
AVSS
P17/ANI7
P16/ANI6
P15/ANI5
P14/ANI4
P13/ANI3
24
25
26
27
20
21
22
23
28
29
30
16
17
18
19
12
13
14
15
7
8
5
6
3
4
1
2
9
10
11
P87/FIP20
VLOAD
P90/FIP21
P91/FIP22
P92/FIP23
P93/FIP24
RH-iXA002AWZZ(Serial No.31000001~402XXXXX)
RH-iXA007AWZZ(Serial No.402XXXXX)
RH-iXA020AWZZ(Serial No.402XXXXX~)
P94/FIP25
P95/FIP26
P96/FIP27
P97/FIP28
P100/FIP29
P101/FIP30
P102/FIP31
P103/FIP32
P104/FIP33
P105/FIP34
P106/FIP35
P107/FIP36
P110/FIP37
P111/FIP38
P112/FIP39
P113/FIP40
P114/FIP41
P115/FIP42
P116/FIP43
P117/FIP44
P120/FIP45
P121/FIP46
P122/FIP47
P123/FIP48
80
79
73
72
71
70
69
68
78
77
76
75
74
62
61
60
59
58
57
56
55
54
53
52
51
67
66
65
64
63
S10
VLOAD
S11
S12
S13
S14
S15
S16
S17
(DIST3)
S18
(DIST2)
S19
(DIST1)
S20
(DIST0)
KARA LATCH
MIC_SW
ILLU LED
DIST
CLAMP SW
DISC SW
TRAY SW1
TRAY SW2
RDS_RDCL
RDS_RDDA
Figure 4 BLOCK DIAGRAM OF IC
8 – 9
XL-HP505
IC851 VHIAN80T53/-1: Multi Regulator (AN80T53)
Pin
No.
1
4
5
2
3
6
7
Terminal Name
REG4 Output
REG3 Output
VCC
GND
MODE 1
REG2 Output
REG1 Output
Function
5.1V power supply with a minimum peak out current of 1200mA.
13V power supply with a minimum peak out current of 1350mA.
Connected to Power supplies.
Connected to the IC substrate.
REG1, REG2,REG3 and REG4 outputs are turned ON when this pin is 5V.
10V power supply with a minimum peak out current of 800mA.
8.5V power supply with a minimum peak out current of 700mA.
Peak Current Protection,
Thermal Protection,
Load Short Protection.
Out puts
5
MODE1
+
-
Prc
Drive
+
-
Prc
Drive
+
-
Prc
Drive
2
REG3
13V
Reference
Voltage
3
VCC
4
GND
1
REG4
5.1V
Figure 5 BLOCK DIAGRAM OF IC
7
REG1
8.5V
+
-
Prc
Drive
6
REG2
10.0V
8 – 10
XL-HP505
[2] FL DISPLAY
FL701 VVKNA11SS55-1
GRID ASSIGNMENT
11G
A1 B
MEMORY ANGLE
DVD
CHAP
VCD CD MP3 X-BASS
TITLE WMAV- SURROUND
TP
TA
(1G)
1G
col col
2G 3G 4G 5G
D5a D5a
D5b D5c
D4a D4a
D4b D4c
D3a D3a
D3b D3c
D2a
D2b
D2a
D2c
D1a
D1b
D1a
D1c
Dot
6G 7G
Dot
8G
f g e r p n d
(2G~9G) a h j k c b m
9G
DAILY
10G
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P1
P2
P3
P4
P5
P6
P 20
ANODE CONNECTION
2G
D4-b
D4-c
3
D3-a
D3-b
D3-c
2
D2-a
D2-b
D2-c
1
D1-a
D1-b
D1-c
1G
5
D5-a
D5-b
D5-c
4
D4-a a b e n g p r c f m d k j h
OUTER DIMENSIONS
3G a b e n g p r c f m d k j h
45
4G a b e n g p r c f m d k j h
5G a b e n g p r c f m d k j h e n g p f m d k j h r c
Dot
6G col a b
1
7G a b e n g p r c f m d k j h r c
Dot e n g p f m d k j h
8G col a b
9G a b e n g p r c f m d k j h
10G
PTYI
(L)
11G
DVD
TA
TP
RDS
RES
DAILY TITLE
PTY
(
)
MHz kHz
ST
VCD
CD
X-BASS
MP3
WMA
V-
SURROUND
CHAP
ANGLE
A
B
1
MEMORY
(R)
SLEEP
PATTERN AREA
PIN CONNECTION
PIN NO.
CONNECTION
45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28
F2 F2 NP NP P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7
27-22
NX
PIN NO.
CONNECTION
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
P5 P4 P3 P2 P1 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP F1 F1
21
P6
8 – 11
XL-HP505
—MEMO—
8 – 12
XL-HP500
PARTS GUIDE
MICRO COMPONENT SYSTEM
MODEL
XL-HP505
XL-HP505 Micro Component System consisting of XL-HP505
(main unit) and CP-HP505 (speaker system).
“HOW TO ORDER REPLACEMENT PARTS”
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER 2. REF. No.
3. PART NO.
4. DESCRIPTION
For U.S.A. only
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor,
Please call Toll-Free;
1-800-BE-SHARP
MARK: SPARE PARTS-DELIVERY SECTION
Explanation of capacitors/resistors parts codes
Capacitors
VCC ....................... Ceramic type
VCK ........................ Ceramic type
VCT ........................ Semiconductor type
VC • • MF ............... Cylindrical type (without lead wire)
VC • • MN ............... Cylindrical type (without lead wire)
VC • • TV ................ Square type (without lead wire)
VC • • TQ ............... Square type (without lead wire)
VC • • CY ............... Square type (without lead wire)
VC • • CZ ............... Square type (without lead wire)
VC • • • • • • • • • J .. The 13th character represents capacity difference.
("J"
±
5%, "K"
±
10%, "M"
±
20%, "N"
±
30%,
"C"
±
0.25 pF, "D"
±
0.5 pF, "Z" +80-20%.)
Resistors
VRD ....................... Carbon-film type
VRS ........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF ............... Cylindrical type (without lead wire)
VR • • MN ............... Cylindrical type (without lead wire)
VR • • TV ................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ............... Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J"
±
5%, "F"
±
1%, "D"
±
0.5%.)
If there are no indications for the electrolytic capacitors, error is
±
20%.
If there are no indications for other parts, the resistors are
±
5% carbon-film type.
CAUTION:FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE F801,802,805 4A, 125V/
F803,804 2A, 125V FUSES.
ATTENTION:POUR ASSURER
UNE LONGUE PROTECTION CONTRE
UN INCENDIE, REMPLACER SEULEMENT
PAR UN FUSIBLE DE
TYPE F801,802,805 4A, 125V/
F803,804 2A, 125V FUSES.
NOTE:
Parts marked with “ ” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
XL-HP505
NO.
PART CODE
PRICE
RANK
DESCRIPTION NO.
PARTS CODE
PRICE
RANK
DESCRIPTION
DIODES
D1
D301,302
D305
D705~709
D711,712
D801
D802
D803,804
D805,806
D842~845
D846
D853
D856
D860~863
D865
D905~907
D909,910
D911,912
LED701
LED708
VD301
VD302,303
ZD1
ZD351
Q1
Q2
Q101~104
Q105~108
Q109
Q110
Q111
Q112
Q113,114
Q302
Q360
Q601~604
Q701
Q702
Q703
Q711
Q712
Q713
Q714
Q715
Q719
Q801
Q841
Q851
Q901~905
Q906
IC101
IC301
IC302
IC303
IC601
IC701
INTEGRATED CIRCUITS
IC1
IC2
IC701
IC701
IC851
IC854
IC901
VHILC78648E-1
VHILA6261//-1
VHIAN7345K/-1
VHITA7358AP-1
VHILC72131/-1
VHILA1832S/-1
RH-IXA007AWZZ J
RH-IXA020AWZZ
J AW CD Digital Signal Proscessor,
LC78648E
J AN Focus/Tracking/Spin/Sled Driver,
LA6261
J AM Playback and Record/Playback
Amp.,AN7345K
J
J
J
J
AG FM Front End,TA7358AP
AP
AN
PLL (Tuner),LC72131
FM IF Det./FM Mpx./AM IF,
VHILC75341/-1
LA1832S
J AM Audio Processor,LC75341
RH-IXA002AWZZ J AX System Microcomputer,
IXA002AW (Serial
No.31000001~402XXXXX)
System Microcomputer,
IXA007AW (Serial
No.402XXXXX)
System Microcomputer,
IXA020AW (Serial
VHIAN80T53/-1
VHIAN78L05/-1
VHISTK41200-1
No.402XXXXX~)
J AL Multi Regulator,AN80T53
J AE Voltage Regulator,AN78L05
J AY Power Amp.,STK412-000
ZD801
ZD802
ZD803
ZD804
ZD902,903
FILTERS
BF301
CF303
CF351
CF352
VHEDZ6R2BSA-1 J AB Zener,6.2V,DZ6.2BSA
VHEDZ6R8BSA-1 J AC Zener,6.8V,DZ6.8BSA
VHEDZ300BSB-1 J AB Zener,30V,DZ30BSB
VHEDZ6R2BSA-1 J AB Zener,6.2V,DZ6.2BSA
VHEDZ120BSB-1 J AB Zener,12V,DZ12BSB
RFILR0008AWZZ J AE Band Pass Filter
RFILF0124AFZZ J AD FM IF,10.7 MHz
RFILF0003AWZZ J AK FM IF
RFILA0009AWZZ J AE AM IF
TRANSFORMERS
1 PT801
1 PT841
T301
T302
T303
T306
T351
RTRNP0509AWZZ J BC Power (Main)
RTRNP0483AWZZ J AL Power (Sub)
RCILB0065AWZZ J AC OSC,FM
RCILI0017AWZZ J AB FM IF
RCILA0052AWZZ J AE AM Antenna
RCILB0067AWZZ J AD AM OSC
RCILI0019AWZZ J AD AM IF
TRANSISTORS
COILS
L1
L103
L312
L351,352
L701
L901,902
L903
VP-XHR82K0000 J AC 0.82
µ
H
VP-MK331K0000 J AB 330
µ
H,Choke
RCILR0056AWZZ J AB FM RF
VP-DH101K0000
VP-DH101K0000
J AB 100
J AB 100
µ
µ
H,Choke
H,Choke
RCILZ0024AWZZ J AC 3
µ
H,Choke
VP-DH2R2K0000 J AB 2.2
µ
H,Peaking
VIBRATORS
VSKTA1504Y/-1 J AB Silicon,PNP,KTA1504 Y
VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 Y
VSKTC3200GR-1 J AC Silicon,NPN,KTC3200 GR
VSKTC3875GR-1 J AB Silicon,NPN,KTC3875 GR
VSKTA1504GR-1 J AB Silicon,PNP,KTA1504 GR
VSKRC104S//-1 J AC Digital,NPN,KRC104 S
VSKTC3203Y/-1 J AC Silicon,NPN,KTC3203 Y
VSKTA1504GR-1 J AB Silicon,PNP,KTA1504 GR
VSKRC104S//-1 J AC Digital,NPN,KRC104 S
VSKTC3194Y/-1 J AD Silicon,NPN,KTC3194 Y
VSKTA1504GR-1 J AB Silicon,PNP,KTA1504 GR
VSKTC3875GR-1 J AB Silicon,NPN,KTC3875 GR
VSKTA1273Y/-1 J AE Silicon,PNP,KTA1273 Y
VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 Y
VSKRC102S//-1
VSKRA102S//-1
VSKRC104S//-1
VSKRA107S//-1
VSKRC104S//-1
J
J
J
J
J
AB
AB
AC
AB
AC
Digital,NPN,KRC102 S
Digital,PNP,KRA102 S
Digital,NPN,KRC104 S
Digital,NPN,KRA107 S
Digital,NPN,KRC104 S
VSKRA107S//-1
VSKRC104S//-1
J AB Digital,NPN,KRA107 S
J AC Digital,NPN,KRC104 S
VSKTA1274Y/-1 J AE Silicon,PNP,KTA1274 Y
VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
VSKRC104S//-1 J AC Digital,NPN,KRC104 S
VSKTC3875GR-1 J AB Silicon,NPN,KTC3875 GR
VSKTC3203Y/-1 J AC Silicon,NPN,KTC3203 Y
XL1
X351
X352
XL700
RCRSP0020AWZZ J AG Crystal,16.9344 MHz
92LCRSTL1425A J AF Crystal,456 kHz
RCRSP0019AWZZ J AF Crystal,4.5 MHz
RCRSP0003AWZZ J AH Crystal,4.19403 MHz
VHDKDS184//-1+ J AC Silicon,KDS184E
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHDMA111///-1
VHDMA111///-1
J
J
AC
AC
Silicon,MA111
Silicon,MA111
VHDD10XB60F-1 J AL Silicon,D10XB60F
VHDD3SBA60F-1 J AG Silicon,D3SBA60F
VHDRL204F//-1 J AC Silicon,RL204F
VHD1N4004S/-1
VHD1N4004S/-1
J
J
AB
AB
Silicon,1N4004S
Silicon,1N4004S
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHD1N4004S/-1 J AB Silicon,1N4004S
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHD1N4004S/-1 J AB Silicon,1N4004S
VHDDS1SS133-1 J AB Silicon,DS1SS133
VHP304VT2H3-1 J AC LED,???,304VT2H3
VHPA304BC2H-1 J AK LED,???,A304BC2H
VHCSVC347S/-1 J AG Variable Capacitance,SVC347S
VHCSVC230C/-1 J AD Variable Capacitance,SVC230C
VHEDZ3R3BSB-1 J AB Zener,3.3V,DZ3.3BSB
VHEDZ5R1BSB-1 J AC Zener,5.1V,DZ5.1BSB
C38
C39,40
C42
C44
C46
C47
C48,49
C50
C51,52
C103
C22
C23,24
C25,26
C27
C28~32
C33
C34
C35
C36
C37
C1
C2
C3
C4
C5
C6
C8
C9
C10
C11
C12
C13
C14,15
C16
C17
C18
C20
C21
CAPACITORS
VCEAZA1EW476M J AB 47
µ
F,25V,Electrolytic
VCKYCY1CB103K J AA 0.01
µ
F,16V
VCEAZA1EW476M J AB 47
µ
F,25V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYCY1HB473K J AB 0.047
µ
F,50V
VCKYCY1CB103K J AA 0.01
µ
F,16V
VCKYCY1HB272K J AA 0.0027
µ
F,50V
RC-EZ0004AWZZ J AD 3.3
µ
F,16V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCTYPA1CX563K J AB 0.056
µ
F,16V
VCCCCY1HH101J J AA 100 pF (CH),50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1AW107M J AB 100
µ
F,10V,Electrolytic
VCEAZA0JW337M J AC 330
µ
F,6.3V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYPA1HF103Z J AB 0.01
µ
F,50V
VCEAZA1AW107M J AB 100
µ
F,10V,Electrolytic
VCKYCY1CB563K J AB 0.056
µ
F,16V
VCKYCY1CB103K J AA 0.01
µ
F,16V
VCEAZA1EW106M J AB 10
µ
F,25V,Electrolytic
VCQYKA1HM152K J AB 0.0015
µ
F,50V,Mylar
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH101J J AA 100 pF (CH),50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH101J J AA 100 pF (CH),50V
VCKYCY1HB473K J AB 0.047
µ
F,50V
VCKYCY1CF224Z J AB 0.22
µ
F,16V
VCKYCY1CB104K J AB 0.1
µ
F,16V
VCKYCY1CB103K J AA 0.01
µ
F,16V
VCEAZA1AW107M J AB 100
µ
F,10V,Electrolytic
VCKYPA1HF103Z J AB 0.01
µ
F,50V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYCY1CB103K J AA 0.01
µ
F,16V
VCEAZA1AW107M J AB 100
µ
F,16V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCKYPA1HF223Z J AB 0.022
µ
F,50V
VCCCCY1HH180J J AA 18 pF(CH),50V
VCKYBT1HB181K J AA 180 pF,50V
– 1 –
NO.
C386
C387
C388
C389
C391
C392
C393
C394
C395
C396
C397
C398
C367,368
C369
C370~372
C373,374
C380
C381
C382
C383
C384
C385
C355
C356
C357
C358
C361
C362
C363
C364
C365
C366
C324
C330
C331
C332
C334
C335
C342,343
C350,351
C352
C353,354
C310
C311
C312
C313
C315
C316
C317
C318
C320
C323
C141
C143
C302
C303
C304
C305
C306
C307
C308
C309
C104
C105,106
C109,110
C111,112
C113,114
C115,116
C117,118
C121
C123,124
C125,126
C127,128
C129,130
C131,132
C133
C134
C135
C137
C138
C139
C140
PART CODE
PRICE
RANK
DESCRIPTION
VCCCCY1HH181J J AA 180 pF (CH),50V
VCKYCY1HB152K J AA 0.0015
µ
F,50V
VCKYCY1HB331K J AA 330 pF,50V
VCEAZA1CW107M J AC 100
µ
F,16V,Electrolytic
VCTYPA1EX333K J AA 0.033
µ
F,25V
VCKYCY1HB561K J AA 560 pF,50V
VCEAZA1EW476M J AB 47
µ
F,25V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCKYCY1HB271K J AA 270 pF,50V
VCEAZA1CW226M J AC 22
µ
F,16V,Electrolytic
VCTYPA1CX223K J AA 0.022
µ
F,16V
VCKYCY1HB332K J AA 0.0033
µ
F,50V
VCEAZA1EW476M J AB 47
µ
F,25V,Electrolytic
VCEAZA1CW226M J AC 22
µ
F,16V,Electrolytic
VCEAZA1AW227M J AC 220
µ
F,10V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCQYKA1HM473K J AB 0.047
µ
F,50V,Mylar
VCQPKA2AA822J J AA 0.0082
µ
F,100V,Polypropylene
VCQYKA1HM393K J AB 0.039
µ
F,50V,Mylar
VCEAZA1EW476M J AB 47
µ
F,25V,Electrolytic
VCEAZA1CW107M J AC 100
µ
F,16V,Electrolytic
VCEAZA1HW335M J AB 3.3
µ
F,50V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCCCCY1HH101J J AA 100 pF (CH),50V
VCKYCY1HB103K J AA 0.01
µ
F,50V
VCCCCY1HH4R7C J AA 4.7 pF (CH),50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1CW106M J AC 10
µ
F,16V,Electrolytic
VCCCCY1HH4R7C J AA 4.7 pF (CH),50V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCCCCY1HH150J J AA 15 pF (CH),50V
VCCCCY1HH180J J AA 18 pF (CH),50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH220J J AA 22 pF (CH),50V
VCKYCY1HB103K J AA 0.01
µ
F,50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYBT1HB101K J AA 100 pF,50V
VCKYBT1HB102K J AA 0.001
µ
F,50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH4R7C J AA 4.7 pF (CH),50V
VCCCCY1HH150J J AA 15 pF (CH),50V
VCKYCY1EF473Z J AB 0.047
µ
F,25V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH220J J AA 22 pF (CH),50V
VCKYCY1HB561K J AA 560 pF,50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1CW106M J AC 10
µ
F,16V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH220J J AA 22 pF (CH),50V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCEAZA1HW225M J AB 2.2
µ
F,50V,Electrolytic
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1HW225M J AB 2.2
µ
F,50V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1HW225M J AB 2.2
µ
F,50V,Electrolytic
VCTYPA1CX223K J AA 0.022
µ
F,16V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCCCCY1HH270J J AA 27 pF (CH),50V
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCTYPA1CX153K J AA 0.015
µ
F,16V
VCEAZA1HW106M J AB 10
µ
F,50V,Electrolytic
VCCCCY1HH120J J AA 12 pF (CH),50V
VCCCCY1HH150J J AA 15 pF (CH),50V
VCKYBT1HB101K J AA 100 pF,50V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYCY1HB103K J AA 0.01
µ
F,50V
VCKYCY1HB331K J AA 330 pF,50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYBT1HB102K J AA 0.001
µ
F,50V
VCEAZA1CW476M J AB 47
µ
F,16V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCEAZA1CW476M J AB 47
µ
F,16V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1AW107M J AB 100
µ
F,10V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1AW107M J AB 100
µ
F,10V,Electrolytic
XL-HP505
C855
C856
C859
C861
C864,865
C874
C901,902
C903,904
C905,906
C907
C908
C909
C910
C911,912
C913
C914,915
C916
C917
C918
C919
C920
C921,922
C923
C925
C928,929
C931
C946
C960
C704
C705
C707
C716,717
C718
C719
C720
C721
C722
C801
C802,803
C804
C805
C806~809
C810,811
C841
C842
C843
1 C844
C854
C399
C601
C602
C603
C605~608
C609
C610
C611,612
C613,614
C615,616
C617~624
C625,626
C639
C640
C651~653
C690,691
C700
C701
C702
C703
NO.
PARTS CODE
PRICE
RANK
DESCRIPTION
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1CW227M J AC 220
µ
F,16V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCEAZA1CW226M J AC 22
µ
F,16V,Electrolytic
VCFYFA1HA154J J AB 0.15
µ
F,50V,Thin Film
RC-EZY105AF1H J AB 1
µ
F,50V,Electrolytic
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCKYCY1HB222K J AA 0.0022
µ
F,50V
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCEAZA1HW475M J AB 4.7
µ
F,50V,Electrolytic
VCEAZA1HW105M J AB 1
µ
F,50V,Electrolytic
VCKYCY1HB222K J AA 0.0022
µ
F,50V
VCEAZA1HW225M J AB 2.2
µ
F,50V,Electrolytic
VCEAZA1HW226M J AB 22
µ
F,50V,Electrolytic
VCKYCY1HB221K J AA 220 pF,50V
VCKYCY1HB391K J AA 390 pF,50V
RC-EZD105AF1H J AB 1
µ
F,50V,Electrolytic
VCEAZA1AW227M J AC 220
µ
F,10V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
VCCCCY1HH150J J AA 15 pF (CH),50V
VCCCCY1HH180J J AA 18 pF (CH),50V
VCKYCY1EF223Z J AB 0.022
µ
F,25V
RC-EZD105AF1H J AB 1
µ
F,50V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCKYCY1HB103K J AA 0.01
µ
F,50V
RC-EZD335AF1H J AB 3.3
µ
F,50V,Electrolytic
VCKYCY1EF223Z J AB 0.022
µ
F,25V
RC-EZD476AF1C J AC 47
µ
F,16V,Electrolytic
VCCCCY1HH151J J AA 150 pF (CH),50V
VCEAZA1VW107M J AC 100
µ
F,35V,Electrolytic
VCEAZA1HW476M J AB 47
µ
F,50V,Electrolytic
VCEAZA1JW227M J AD 220
µ
F,63V,Electrolytic
VCEAZA2AW226M J AC 22
µ
F,100V,Electrolytic
VCQYKA1HM104K J AB 0.1
µ
F,50V,Mylar
VCFYDA2AA224J J AD 0.22
µ
F,100V,Thin Film
VCEAZA0JW108M J AC 1000
µ
F,6.3V,Electrolytic
VCEAZA1VW477M J AD 470
µ
F,35V,Electrolytic
VCQYKA1HM473K J AB 0.047
µ
F,50V,Mylar
RC-KZ002LAWZZ J AC 0.0047
µ
F,250V,Ceramic
VCEAZA1EW227M J AC 220
µ
F,25V,Electrolytic
VCEAZA1HW106M J AB 10
µ
F,50V,Electrolytic
VCEAZW1EW338M J AG 3300
µ
F,25V,Electrolytic
VCEAZA1EW226M J AB 22
µ
F,25V,Electrolytic
VCKZPA1HF223Z J AA 0.022
µ
F,50V
VCEAZA1EW226M J AB 22
µ
F,25V,Electrolytic
VCQYKA1HM104K J AB 0.1
µ
F,50V,Mylar
VCEAZA1HW104M J AB 0.1
µ
F,50V,Electrolytic
VCKYCY1HB102K J AA 0.001
µ
F,50V
VCEAZA1HW226M J AB 22
µ
F,50V,Electrolytic
VCCCCY1HH101J J AA 100 pF (CH),50V
VCCCCY1HH3R0C J AA 3 pF (CH),50V
VCQYKA1HM104K J AB 0.1
µ
F,50V,Mylar
VCCCCY1HH3R0C J AA 3 pF (CH),50V
VCEAZA2AW107M J AD 100
µ
F,100V,Electrolytic
VCCCCY1HH101J J AA 100 pF (CH),50V
VCEAZA2AW107M J AD 100
µ
F,100V,Electrolytic
VCEAZA1HW107M J AC 100
µ
F,50V,Electrolytic
VCKYCY1HB103K J AA 0.01
µ
F,50V
VCEAZA1HW107M J AC 100
µ
F,50V,Electrolytic
VCKYCY1HB103K J AA 0.01
µ
F,50V
RC-EZ0027AWZZ J AN 3300
µ
F,63V,Electrolytic
RC-EZ0115AWZZ J AH 4700
µ
F,35V,Electrolytic
RC-EZ0027AWZZ J AN 3300
µ
F,63V,Electrolytic
VCEAZA1HW476M J AB 47
µ
F,50V,Electrolytic
VCQYKA1HM104K J AB 0.1
µ
F,50V,Mylar
VCEAZA1HW106M J AB 10
µ
F,50V,Electrolytic
VCEAZA1HW104M J AB 0.1
µ
F,50V,Electrolytic
VCEAZA1EW335M J AB 3.3
µ
F,25V,Electrolytic
RESISTORS
R026
R05,06
R3
R6
R7
R8
R9
R10
R12
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB000J
J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
VRD-ST2CD563J J AA 56 kohm,1/6W
VRD-ST2CD563J J AA 56 kohm,1/6W
VRD-ST2CD470J J AA 47 ohms,1/6W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRS-CY1JB100J J AA 10 ohm,1/16W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRS-CY1JB331J J AA 330 ohms,1/16W
– 2 –
NO.
R309
R311
R313
R314
R316
R322
R323
R325
R327
R336
R350
R351
R352
R353
R355
R356
R357
R358
R359
R360
R365
R372~374
R126,127
R128,129
R130,131
R132,133
R134,135
R136,137
R138
R139
R140
R141
R142
R143
R144
R145
R146,147
R148
R149
R150
R158
R302
R47
R48,49
R50~54
R55
R56
R57
R58
R103,104
R105,106
R107,108
R109,110
R111
R112
R113
R114
R115,116
R117,118
R119,120
R121,122
R123,124
R13
R14,15
R16
R17
R18
R19
R20
R21
R22
R24,25
R26,27
R28
R30,31
R32~38
R39,40
R41
R42
R43
R44
R45
XL-HP505
PART CODE
PRICE
RANK
DESCRIPTION
VRD-ST2CD822J J AA 8.2 kohms,1/6W
VRD-ST2CD682J J AA 6.8 kohms,1/6W
VRD-ST2CD153J J AA 15 kohm,1/6W
VRS-CY1JB682J J AA 6.8 kohms,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB562J J AA 5.6 kohms,1/16W
VRD-ST2CD472J J AA 4.7 kohms,1/6W
VRS-CY1JB472J J AA 4.7 kohms,1/16W
VRD-ST2CD101J J AA 100 ohm,1/6W
VRS-CY1JB222J J AA 2.2 kohms,1/16W
VRS-CY1JB103J J AA 10 kohm,1/16W
VRD-ST2CD222J J AA 2.2 kohms,1/6W
VRD-ST2CD222J J AA 2.2 kohms,1/6W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB681J J AA 680 ohms,1/16W
VRS-CY1JB563J J AA 56 kohms,1/16W
VRD-ST2EE1R0J J AA 1 ohm,1/4W
VRS-CY1JB221J J AA 220 ohms,1/16W
VRD-ST2EE1R0J J AA 1 ohm,1/4W
VRD-ST2CD101J J AA 100 ohm,1/6W
VRD-ST2CD222J J AA 2.2 kohms,1/6W
VRS-CY1JB103J J AA 10 kohm,1/16W
VRS-CY1JB472J
VRS-CY1JB473J
J
J
AA
AA
4.7 kohms,1/16W
47 kohms,1/16W
VRD-ST2CD391J J AA 390 ohms,1/6W
VRS-CY1JB225J
VRS-CY1JB103J
VRS-CY1JB222J
VRS-CY1JB332J
VRS-CY1JB473J
J
J
J
J
J
AA
AA
AA
AA
AA
2.2 ohms,1/6W
10 kohm,1/16W
2.2 kohms,1/16W
3.3 kohms,1/16W
47 kohms,1/16W
VRS-CY1JB472J J AA 4.7 kohms,1/16W
VRD-ST2CD153J J AA 15 kohms,1/6W
VRS-CY1JB153J
VRS-CY1JB102J
J
J
AA
AA
15 kohms,1/16W
1 kohm,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRD-ST2CD560J J AA 56 ohms,1/6W
VRS-CY1JB104J J AA 100 kohm,1/16W
VRS-CY1JB392J
VRS-CY1JB123J
VRS-CY1JB682J
J
J
J
AA
AA
AA
3.9 kohms,1/16W
12 kohms,1/16W
6.8 kohms,1/16W
VRS-CY1JB472J
VRS-CY1JB562J
VRS-CY1JB152J
VRS-CY1JB101J
VRS-CY1JB103J
J AA 4.7 kohms,1/16W
J AA 5.6 kohms,1/16W
J AA 1.5 kohms,1/16W
J AA 100 ohm,1/16W
J AA 10 kohm,1/16W
VRD-ST2CD224J J AA 220 kohms,1/6W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRS-CY1JB103J
VRS-CY1JB473J
J
J
AA
AA
10 kohm,1/16W
47 kohms,1/16W
VRD-ST2CD472J J AA 4.7 kohms,1/6W
VRD-RT2HD820J J AA 82 ohms,1/2W
VRS-CY1JB473J J AA 47 kohms,1/16W
VRS-CY1JB223J J AA 22 kohms,1/16W
VRD-ST2CD4R7J J AA 4.7 ohms,1/6W
VRS-CY1JB103J J AA 10 kohm,1/16W
VRS-CY1JB472J J AA 4.7 kohms,1/16W
VRD-ST2EE151J J AA 150 ohms,1/4W
VRS-CY1JB683J J AA 68 kohms,1/16W
VRD-ST2EE221J J AA 220 ohms,1/4W
VRS-CY1JB100J J AA 10 ohm,1/16W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRS-CY1JB104J J AA 100 kohm,1/16W
VRS-CY1JB333J J AA 33 kohms,1/16W
VRD-ST2CD220J J AA 22 ohms,1/6W
VRS-CY1JB472J J AA 4.7 kohms,1/16W
VRS-CY1JB681J
VRS-CY1JB683J
VRS-CY1JB473J
VRS-CY1JB000J
VRS-CY1JB103J
J
J
AA
AA
680 ohms,1/16W
68 kohms,1/16W
J AA 47 kohms,1/16W
J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
J AA 10 kohm,1/16W
VRS-CY1JB272J
VRS-CY1JB562J
VRS-CY1JB102J
VRS-CY1JB271J
VRS-CY1JB332J
J AA 2.7 kohms,1/16W
J AA 5.6 kohms,1/16W
J AA 1 kohm,1/16W
J AA 270 ohms,1/16W
J AA 3.3 kohms,1/16W
VRS-CY1JB102J
VRS-CY1JB474J
J AA 1 kohm,1/16W
J AA 470 kohms,1/16W
VRD-ST2CD392J J AA 3.9 kohms,1/6W
VRS-CY1JB182J J AA 1.8 kohms,1/16W
VRS-CY1JB472J J AA 4.7 kohms,1/16W
VRS-CY1JB103J
VRS-CY1JB102J
J AA 10 kohm,1/16W
J AA 1 kohm,1/16W
NO.
R773
R774
R775,776
R779
R780
R781,782
R783
R784~787
R789
R790
R793,794
R795
R796
R797
R798
R799
R801
R802
R803
R804,805
R806
R807
R720
R721
R723~725
R726,727
R728
R729
R730
R731
R732
R734
R735~737
R746,747
R748
R755
R761
R763
R766
R770
R771
R772
R601~603
R604,605
R606,607
R608,609
R610,611
R612,613
R614~617
R618
R619
R620,621
R641,642
R643,644
R645
R690,691
R692,693
R700~702
R704,705
R708~713
R714~717
R718
R375
R376
R377
R378
R379
R380
R381
R382
R383
R384
R385
R386
R387
R388
R391,392
R393
R395
R562~565
R566
R573
PARTS CODE
PRICE
RANK
DESCRIPTION
VRD-ST2CD471J J AA 470 ohms,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB473J
VRS-CY1JB102J
VRS-CY1JB222J
J
J
J
AA
AA
AA
47 kohms,1/16W
1 kohm,1/16W
2.2 kohms,1/16W
VRS-CY1JB152J
VRS-CY1JB103J
J AA 1.5 kohms,1/16W
J AA 10 kohm,1/16W
VRD-ST2EE151J J AA 150 ohms,1/4W
VRS-CY1JB562J J AA 5.6 kohms,1/16W
VRD-ST2CD562J J AA 5.6 kohms,1/6W
VRS-CY1JB562J J AA 5.6 kohms,1/16W
VRD-ST2CD223J J AA 22 kohms,1/6W
VRD-ST2CD562J J AA 5.6 kohms,1/6W
VRS-CY1JB392J J AA 3.9 kohms,1/16W
VRD-ST2EE271J J AA 270 ohms,1/4W
VRS-CY1JB102J
VRS-CY1JB473J
VRS-CY1JB103J
VRS-CY1JB822J
J
J
J
J
AA
AA
AA
AA
1 kohm,1/16W
47 kohms,1/16W
10 kohm,1/16W
8.2 kohms,1/16W
VRS-CY1JB151J1 J AA 150 ohms,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRS-CY1JB332J
VRS-CY1JB122J
VRS-CY1JB222J
J
J
J
AA
AA
AA
3.3 kohms,1/16W
1.2 kohms,1/16W
2.2 kohms,1/16W
VRS-CY1JB391J
VRS-CY1JB222J
J AA 390 ohms,1/16W
J AA 2.2 kohms,1/16W
VRD-ST2CD331J J AA 330 ohms,1/6W
VRS-CY1JB331J J AA 330 ohms,1/16W
VRS-CY1JB223J J AA 22 kohms,1/16W
VRS-CY1JB103J
VRS-CY1JB682J
VRS-CY1JB000J
VRS-CY1JB682J
VRS-CY1JB393J
J AA 10 kohm,1/16W
J AA 6.8 kohms,1/16W
J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
J AA 6.8 kohms,1/16W
J AA 39 kohms,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB681J
VRS-CY1JB222J
J
J
AA
AA
680 ohms,1/16W
2.2 kohms,1/16W
VRD-ST2CD561J J AA 560 ohms,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB102J
VRS-CY1JB000J
J AA 1 kohm,1/16W
J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
VRD-ST2CD681J J AA 680 ohms,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB473J J AA 47 kohms,1/16W
VRD-ST2EE1R5J J AA 1.5 ohms,1/4W
VRS-CY1JB103J
VRS-CY1JB102J
VRS-CY1JB151J
J
J
J
AA
AA
AA
10 kohm,1/16W
1 kohm,1/16W
150 ohms,1/16W
VRS-CY1JB472J
VRS-CY1JB822J
J AA 4.7 kohms,1/16W
J AA 8.2 kohms,1/16W
VRS-CY1JB103J J AA 10 kohm,1/16W
VRD-ST2CD472J J AA 4.7 kohms,1/6W
VRS-CY1JB272J J AA 2.7 kohms,1/16W
VRS-CY1JB472J J AA 4.7 kohms,1/16W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRS-CY1JB103J
VRS-CY1JB103J
J
J
AA
AA
10 kohm,1/16W
10 kohm,1/16W
VRD-ST2CD562J J AA 5.6 kohms,1/6W
VRS-CY1JB103J J AA 10 kohm,1/16W
VRD-ST2EE1R5J J AA 1.5 ohms,1/4W
VRS-CY1JB473J
VRS-CY1JB104J
J
J
AA
AA
47 kohms,1/16W
100 kohm,1/16W
VRD-ST2CD101J J AA 100 ohm,1/6W
VRS-CY1JB562J J AA 5.6 kohms,1/16W
VRD-ST2CD104J J AA 100 kohm,1/6W
VRD-ST2CD473J J AA 47 kohms,1/6W
VRD-ST2CD123J J AA 12 kohms,1/6W
VRD-ST2EE470J J AA 47 ohms,1/4W
VRD-ST2CD473J J AA 47 kohms,1/6W
VRD-ST2EE100J J AA 10 ohm,1/4W
– 3 –
XL-HP505
NO.
PART CODE
PRICE
RANK
DESCRIPTION NO.
PARTS CODE
PRICE
RANK
DESCRIPTION
R968
RD01
RD02
RD03
RD04
RD08
RD09
RD10
RD11
RD12
RD13
RD14
RD15
RD16
RD17
RD18
RD19
RD20
RD21
RD22
RD23
RD24
RD25
R917
R918
R919,920
R921
R922
R925,926
R927,928
R929,930
R934,935
R937
R938~941
R942,943
R944,945
R946
R947
R949
R950
R956
1
R958
R965,966
R808
R841
R842
R843
R844
R853
R854
R857
R858
R859
R863
R864
R890
R901,902
R903,904
R905,906
R907
R908
R909
R910
R911
1 R912
R913
R916
VRD-RT2HD222J J AA 2.2 kohms,1/2W
VRD-ST2CD224J J AA 220 kohms,1/6W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRD-ST2CD473J J AA 47 kohms,1/6W
VRD-ST2EE820J J AA 82 ohms,1/4W
VRD-ST2CD223J J AA 22 kohms,1/6W
VRD-ST2CD332J J AA 3.3 kohms,1/6W
VRD-ST2CD223J J AA 22 kohms,1/6W
VRD-ST2CD221J J AA 220 ohms,1/6W
VRD-ST2CD103J J AA 10 kohm,1/6W
VRD-RT2HD3R3J J AA 3.3 ohms,1/2W
VRD-ST2CD223J J AA 22 kohms,1/6W
RR-HZ0001AWZZ J AE 4.7 Mohms,1/2W
VRS-CY1JB563J J AA 56 kohms,1/16W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB561J
VRS-CY1JB563J
VRS-CY1JB102J
VRS-CY1JB333J
J
J
J
J
AA
AA
AA
AA
560 ohms,1/16W
56 kohms,1/16W
1 kohm,1/16W
33 kohms,1/16W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRS-CY1JB563J J AA 56 kohms,1/16W
VRG-ST2EC101J J AB 100 ohm,1/4W,Fusible
VRN-VV3LAR22J J AC 0.22 ohms,3W
VRN-VV3LAR22J J AC 0.22 ohms,3W
VRN-VV3LAR10J J AD 0.1 ohm,3W
VRS-CY1JB152J
VRS-CY1JB182J
J AA 1.5 kohms,1/16W
J AA 1.8 kohms,1/16W
VRS-CY1JB152J J AA 1.5 kohms,1/16W
VRN-VV3LAR10J J AD 0.1 ohm,3W
VRD-RT2HD152J J AA 1.5 kohms,1/2W
VRD-ST2EE393J
VRD-ST2EE473J
J AA 39 kohms,1/4W
J AA 47 kohms,1/4W
VRD-ST2CD563J J AA 56 kohms,1/6W
VRD-ST2CD563J J AA 56 kohms,1/6W
VRD-RT2HD100J J AA 10 ohm,1/2W
VRS-VV3DA391J J AC 390 ohms,2W
VRD-ST2CD152J J AA 1.5 kohms,1/6W
VRS-CY1JB473J J AA 47 kohms,1/16W
VRD-ST2CD153J J AA 15 kohms,1/6W
VRD-ST2CD102J J AA 1 kohm,1/6W
VRD-ST2CD683J J AA 68 kohms,1/6W
VRS-CY1JB000J J AA 0 ohm,Jumper,0.8
×
1.55mm,Green
VRG-ST2EC101J J AB 100 ohm,1/4W,Fusible
VRD-RT2HD822J J AA 8.2 kohms,1/2W
VRD-RT2HD391J J AA 390 ohms,1/2W
VRS-CY1JB681J
VRS-CY1JB821J
J
J
AA
AA
680 ohms,1/16W
820 ohms,1/16W
VRS-CY1JB102J
VRS-CY1JB152J
J
J
AA
AA
1 kohm,1/16W
1.5 kohms,1/16W
VRD-ST2CD681J J AA 680 ohms,1/6W
VRD-ST2CD821J J AA 820 ohms,1/6W
VRS-CY1JB102J J AA 1 kohm,1/16W
VRS-CY1JB152J
VRS-CY1JB222J
VRS-CY1JB272J
J
J
J
AA
AA
AA
1.5 kohms,1/16W
2.2 kohms,1/16W
2.7 kohms,1/16W
VRD-ST2CD392J J AA 3.9 kohms,1/6W
VRS-CY1JB562J J AA 5.6 kohms,1/16W
VRS-CY1JB103J
VRS-CY1JB681J
VRS-CY1JB821J
J
J
J
AA
AA
AA
10 kohm,1/16W
680 ohms,1/16W
820 ohms,1/16W
VRS-CY1JB102J
VRS-CY1JB152J
VRS-CY1JB222J
VRS-CY1JB272J
VRS-CY1JB392J
VRS-CY1JB562J
VRS-CY1JB103J
J AA 1 kohm,1/16W
J AA 1.5 kohms,1/16W
J AA 2.2 kohms,1/16W
J AA 2.7 kohms,1/16W
J AA 3.9 kohms,1/16W
J AA 5.6 kohms,1/16W
J AA 10 kohm,1/16W
OTHER CIRCUITRY PARTS
BI102/CNS102 QCNWN2748AWPZ J AL Connector Ass’y,8/6Pin
BI601/CNS2
BI703A/B
BI707/CNS707 QCNWN2505AWZZ J AC Connector Ass’y,2/2Pin
BI801/CNS801 QCNWN2753AWPZ J AK Connector Ass’y,11/10Pin
BI802/CNS802 QCNWNA056AWPZ J AF Connector Ass’y,7/6Pin
BI902/CNS902 QCNWN2756AWPZ J AF Connector Ass’y,5/4Pin
CNB1
CNP1
CNP2
CNP3
QCNWN2750AWPZ J
QCNWN2747AWPZ J
QCNCWZO11AWZZ J
QCNCWYP16AWZZ J
92LCONE8P53254 J
92LCONE6P53253 J
AG Connector Ass’y,9/8Pin
AB
AC
AD
AC
AC
Flat Wire,2Pin
Socket,11Pin
Socket,16Pin
Plug,8Pin
Plug,6Pin
RX701
SO302
SO901
SP1
SP2
SP3
SP4
SW1
SW1A
SW2
SW3
SW4
SW701
CNP3A
CNP4
CNP5
CNP301
CNP303
CNP701A
CNP701B
CNP702
CNP704
CNP706A
CNP706B
CNP707
CNP708
CNP801
CNP802
CNP902
CNP971
CNS303
CNS971
CNW3
1
F801
1 F802
1
F803
1 F804
1 F805
FFC1
FFC4
92LCONE6P53254 J
QCNCWZX11AWZZ J
QCNCWZY14AWZZ J
92LCONE2P5268 J
QCNCM010PAWZZ J
AC
AC
AD
AB
AD
Plug,6Pin
Socket,11Pin
Socket,14Pin
Plug,2Pin
Plug,14Pin
QCNCWYH21AWZZ J AE Socket,21Pin
QCNCWYP21AWZZ J AD Socket,21Pin
QCNCWZY07AWZZ J AC Socket,7Pin
QCNCWZX14AWZZ J AD Socket,14Pin
QCNCWYP07AWZZ J AC Socket,7Pin
QCNCWYP07AWZZ J AC Socket,7Pin
92LCONE2P53253 J AB Plug,2Pin
QCNCW012EAWZZ J AC Socket,5Pin
92LCONEAP5267X J AC Plug,10Pin
92LCONE6P53253 J AC Plug,6Pin
92LCONE4P5267X J AB Plug,4Pin
92LCONE2P53253 J AB Plug,2Pin
QCNCW010PAWZZ J AE Socket,14Pin
QCNWNA057AWPZ J AC Connector Ass’y,2Pin
QCNWN2699AWPZ J AF Connector Ass’y,6/6Pin
FFC5
FFC701
FFC702
FFC706
FL701
FW901
JK690
JK701
QFS-D402DAWNI J AC Fuse,4A,125V
QFS-D402DAWNI J AC Fuse,4A,125V
QFS-D202DAWNI J AC Fuse,2A,125V
QFS-D202DAWNI J AC Fuse,2A,125V
QFS-D402DAWNI J AC Fuse,4A,125V
QCNWN2700AWPZ J AE Flat Cable,16Pin
QCNWN2701AWPZ J AD Flat Cable,11Pin
QCNWN2741AWPZ J AE Flat Cable,14Pin
QCNWN2737AWPZ J AE Flat Cable,21Pin
QCNWN2740AWPZ J AD Flat Cable,7Pin
QCNWNA043AWPZ J
VVKNA11SS55-1
QSOCJ0224AWZZ
QJAKM0004AWZZ
J
QCNWN2746AWPZ J
J
J
AD
AV
AC
AC
AK
Flat Cable,7Pin
FL Display
Flat Wire,5Pin
Jack,Video/AUX
Jack,Headphones
JK953
M1
M1A
M2
M2A
QSOCJ0111AWZZ J
92LMTR5529AASY J
92LMTR5515CASY J
92LMTR5529AASY J
92LMTR1854BASY J
AD
AD
AD
AP
Sub Woofer Output
Motor with Gear [Tray]
Motor with Chassis [Spindle]
Motor with Gear [Main Cam]
Motor with Gear [Sled]
M971(202-3) RMOTV0027AWZZ J AM Motor,Air Cooling Fan
1 RL841 RRLYD0018AWZZ J AH Relay
RL914 RRLYD0016AWZZ J AK Relay
RX1 VHPGP1S094HCZ J AF Photo Interrupter
SW702
VHLGP1UM271-1
RSP-ZA010AWZZ
QSW-P9003AWZZ
J
J
J
AH
AR
AD
Remote Sensor,GP1UM271
QTANC0206AWZZ J AD Terminal,FM Antenna
QTANA0426AWZZ J AE Terminal,Speaker
RSP-ZA009AWZZ J AZ Woofer
RSP-ZA009AWZZ J AZ Woofer
Tweeter
RSP-ZA010AWZZ J AR Tweeter
QSW-P9003AWZZ J AD Switch,Push Type [CLAMP]
QSW-F9001AW01 J AD Switch,Leaf Type [PICKUP IN]
QSW-P9003AWZZ J AD Switch,Push Type [TRAY SW1]
Switch,Push Type [TRAY SW2]
QSW-P9006AWZZ J AF Switch,Push Type [DISC]
QSW-K0005AWZZ J AC Switch,Key Type
[ON/STAND-BY]
QSW-K0005AWZZ J AC Switch,Key Type
[CLOCK/TIMER]
SW703
SW704
SW705
SW709
SW710
SW711
SW712
SW713
SW714
SW715
SW716
SW717
SW718
SW719
SW720
QSW-K0005AWZZ J AC Switch,Key Type
[REVERSE MODE]
QSW-K0005AWZZ J AC Switch,Key Type
[REVERSE PLAY]
QSW-K0005AWZZ J AC Switch,Key Type
[PRESET DOWN]
QSW-K0005AWZZ J AC Switch,Key Type [CD]
QSW-K0005AWZZ J AC Switch,Key Type
[TUNER (BAND)]
QSW-K0005AWZZ J AC Switch,Key Type [VIDEO/AUX]
QSW-K0005AWZZ J AC Switch,Key Type [TAPE]
QSW-K0005AWZZ J AC Switch,Key Type [REC/PAUSE]
QSW-K0005AWZZ J AC Switch,Key Type
[TUNING/TIME UP]
QSW-K0005AWZZ J AC Switch,Key Type
[TUNING/TIME DOWN]
QSW-K0005AWZZ J AC Switch,Key Type [STOP]
QSW-K0005AWZZ J AC Switch,Key Type [PLAY]
QSW-K0005AWZZ J AC Switch,Key Type [PRESET UP]
QSW-K0005AWZZ J AC Switch,Key Type
[X-BASS/DEMO]
QSW-K0005AWZZ J AC Switch,Key Type [EQUALISER]
– 4 –
XL-HP505
NO.
PART CODE
PRICE
RANK
DESCRIPTION NO.
PARTS CODE
PRICE
RANK
DESCRIPTION
301
302
304
305
1 306
306- 1
306- 2
306- 3
307
308
701
703
704
M1A
M2A
SW4
120
128
129
130
131
132
133
134
135
136
137
138
121
122
123
124
125
126
127
SW721
SW722
115
116
117
118
119
110
111
112
113
114
109- 1
109- 2
109- 3
109- 4
109- 5
101
102
103
104
105
106
107
108
109
SW723
SW724
SW725
SW726
SW727
SW728
VR701
WTM901
QSW-K0005AWZZ J AC Switch,Key Type
QSW-K0005AWZZ J AC Switch,Key Type
QSW-K0005AWZZ J AC
QSW-K0005AWZZ J AC Switch,Key Type [DISC 2]
QSW-K0005AWZZ J AC Switch,Key Type [DISC 3]
QSW-K0005AWZZ J AC Switch,Key Type [DISC 4]
QSW-K0005AWZZ J AC Switch,Key Type [DISC 5]
QSW-K0005AWZZ
QSW-ZA002AWZZ
QCNCW019EAWZZ J
CD MECHANISM PARTS
J
J
NGERH0011AWZZ J AC Gear,Middle
NGERH0012AWZZ J AC Gear,Drive
NSFTM0020AWFW J AD Shaft,Guide
92LMCUSN1524A J AD Cushion
92LHPC1LFASY J BB Pickup Unit Ass’y
———— –– Pickup Unit
(Not Replacement Item)
NGERR0043AFZZ J AC Gear,Rack
MSPRC0961AFZZ J AA Spring,Rack
PCUSG0001AWSA J AD Cushion
PCUSG0004AWSA J AD Cushion
XBSSD26P06000 J AA Screw,ø2.6
×
6mm
XBBSD20P03000 J AA Screw,ø2
×
3mm
LX-WZ1070AFZZ J AA Washer,ø1.5
×
ø3.8
×
0.25mm
92LMTR5515CASY J
92LMTR1854BASY J
QSW-F9001AW01 J
AC
AF
AB
AP
AD
Switch,Key Type [DISC 1]
Switch,Key Type
Switch,Rotary Type [VOLUME]
Socket,5Pin
Motor with Chassis [Spindle]
Motor with Gear [Sled]
Switch,Leaf Type [Pickup In]
CHANGER MECHANISM PARTS
[MEMORY/SET]
[DIRECT PLAY]
[OPEN/CLOSE]
GCOVA1513AWZZ J AF Disc Tray
GCOVA1514AWZZ J AF Guide Tray
LANGG0008AWZZ J AD Outer Tray Guide
LANGG0009AWZZ J AC Inner Tray Guide
LCHSM0194AWZZ J AP Main Base
LHLDZ9017AWZZ J AF CD Mechanism Holder
LPLTP0014AWZZ J AK Top Plate
LPLTP0015AWZZ J AG Gear Plate
MHOLD5529ASY J AP Up/Down Holder Ass’y
LHLDM9001AWZZ J AD Stabilizer
LHLDZ9019AWM1 J AK Up/Down Holder Ass’y
LPLTM0017AWZZ J AB Stabilizer Plate
LPLTMA001AWFW J AC Plate
PMAGF0003AWZZ J AF Magnet
MLEVP0129AWZZ J AC Tray Lock Lever
MLEVP0130AWZZ J AG Gear Up/Down Board
MLEVP0131AWZZ J AD Mechanism Up/Down Board (L)
MLEVP0132AWZZ J AD Mechanism Up/Down Board (R)
MLEVP0133AWZZ J AC Mechanism Clamp Board
MLEVP0134AWZZ J AD L/R Joint Lever
MLEVP0135AWZZ J AC Tray Set Lever
MLEVP0136AWZZ J AC Mechanism Clamp Switch Lever
MLEVP0137AWZZ J AC Mechanism Clamp Switch Arm
MLEVP0138AWZZ J AB Gear Up/Down Lever, Tray Rear
Drive
MLEVP0139AWZZ J AC Gear Up/Down Lever, Tray Front
Drive
MSPRC0044AWFJ J AB Shift Spring
MSPRD0191AWFJ J AC Disc Stop Spring
MSPRD0192AWFJ J AB Balance Spring
NGERH0176AWZZ J AF Tray Big Gear
NGERH0177AWZZ J AC Tray Front Gear A
NGERH0178AWZZ J AC Tray Front Gear B
NGERH0179AWZZ J AC Tray Rear Gear A
NGERH0180AWZZ J AB Tray Rear Gear B
NGERH0181AWZZ J AC Mechanism Clamp Gear A
NGERH0182AWZZ J AC Mechanism Clamp Joint Gear
NGERH0183AWZZ J AC Mechanism Clamp Board Gear
NGERH0184AWZZ J AC Tray Rear Joint Gear A
NGERH0185AWZZ J AC Tray Rear Joint Gear B
NGERH0186AWZZ J AC Tray Rear Joint Gear C
NGERH0187AWZZ J AB Tray Rear Drive Gear
NGERH0188AWZZ J AC Tray Drive Gear
NGERH0189AWZZ J AB Tray Front Drive Gear
NGERH0190AWZZ J AC Tray Front Joint Gear
139
140
141
142
143
144
145
146
147
148
149
150
151
152
801
802
803
804
M1
M2
SW1
SW2
SW3
SW4
NGERH0191AWZZ J AE Mode Big Gear
NGERH0192AWZZ J AC G-Up/Down Gear A
NGERH0193AWZZ J AC G-Up/Down Gear B
NGERH0194AWZZ J AB Mechanism Up/Down Gear A
NGERH0195AWZZ J AC Mechanism Up/Down Gear B
NGERH0196AWZZ J AC Mechanism Clamp Switch Gear
NGERH0198AWZZ J AB Reduction Gear A
NGERH0199AWZZ J AB Reduction Gear B
NGERH0200AWZZ J AB Reduction Gear C
NGERH0201AWZZ J AB Reduction Gear D
NGERH0202AWZZ J AB Up/Down Reduction Gear E
NGERH0203AWZZ J AB Up/Down Reduction Gear F
NGERH0204AWZZ J AB Tray Reduction Gear E
NSFTT0084AWFD J AD Shaft,Main Base
LX-BZA006AWFD J AB Screw,Special
LX-EZ0005AWFD J AA Screw,Special
XEBSD20P10000 J AA Screw,ø2
×
10mm
XEBSD30P10000 J AA Screw,ø3
×
10mm
92LMTR5529AASY J
92LMTR5529AASY J
QSW-P9003AWZZ
QSW-P9003AWZZ
QSW-P9003AWZZ
QSW-P9006AWZZ
CABINET PARTS
J
J
J
J
AD
AD
AD
AD
AD
AF
Motor with Gear [Tray]
Motor with Gear [Main Cam]
Switch,Push Type [CLAMP]
Switch,Push Type [TRAY SW1]
Switch,Push Type [TRAY SW2]
Switch,Push Type [DISC]
201 CCABA5609AW01 J Front Panel Ass’y
201- 1
201- 2
201- 3
201- 4
201- 5
201- 6
201- 7
201- 8
201- 9
201-10
201-11
201-12
201-13
201-14
201-15
201-16
201-17
201-18
201-19
201-20
201-21
201-22
201-23
202
202- 1
202- 2
————
GCOVA1364AWSA J
GCOVA1524AWSA J
JKNBZ1000AWSA
MLIFP0008AWZZ
CFANB5609AW01
NFANP0001AWZZ
J
J
MLOKC0015AWZZ J
MSPRD0180AWFJ J
MSPRD0197AWFJ J
J
LANGK0434AWFW J
J
––
AB
AC
AE
AD
AC
AB
AC
AD
Front Panel
Indicator,Timer
Cover,Sensor
GCOVA1531AWSA J AG Decoration Panel,Front A
GCOVA1532AWSA J AG Decoration Panel,Front B
GCOVA1523AWSA J AH Panel,Cassette Cover
GDORF0117AWSA J AF Holder,Cassette
HBDGB1001AWSA J AD Badge,SHARP
HDECQ1111AWSA J AB Window,Cassette
HDECQ1112AWSA J AD Panel,FL Display
HDECQ1113AWSA J AD Indicator,Volume Knob
HDECZ0034AWSA J AQ Decoration Panel,Center
JKNBZ0994AWSA J AE Button,Power ON/STAND-BY
JKNBZ0995AWSA J AE Button,Disc Select
JKNBZ0996AWSA J AE Button,X-Bass
JKNBZ0997AWSA J AF Button,Play/Stop
JKNBZ0998AWSA J AF Button,Play/Rev
JKNBZ0999AWSA J AE Button,Function
Button,Tuning/Rec
Damper
Lock Lever,Cassette
Spring,Cassette Lock Lever
Spring,Cassette Holder
AQ Fan Motor Ass’y
AF Bracket,Fan Motor
Rotary,Fan
224
225
226
1 228
229
1
230
231
218
219
220
221
223
213
214
215
216
217
202- 3(M971) RMOTV0027AWZZ J AM Motor,Air Cooling Fan
202- 4 92LCSPR1431C J AA Spring,Ring
203
204
205
92LCSPR1431C
GCAB-3100AWSA
J
J
GCOVA1525AWSA J
AA Spring,Ring
AW Cabinet
AF Disck Tray Cover
210
211
211
212
GITAR1269AWSA
GITARA003AWSA
J
J
AM Rear Panel,Bottom
Rear Panel,Top
[Except for U.S.A.]
GITAR1268AWSA J AK Rear Panel,Top [For U.S.A.]
JKNBK0104AWSA J AK Knob,VOLUME
KMECBA003AWZZ J
LANGT0042AWFW J
LBND-1011AWZZ
LBSHC0005AWZZ
J
J
LCHSM0197AWFW J
LCHSZ0026AWZZ J AM Chassis,Changer Unit
LHLDZ9023AWZZ J AD Holder,FL Display
PCUSG0022AWZZ J AB Cushion,Leg
PRDARA019AWFW J AV Heat Sink,Main
PSHEPA003AWZZ J
PSHEPA004AWZZ J
PSHEZA012AWZZ
PSHEZA013AWZZ
J
J
QACCD0022AWZZ J
QCNWN1860AWZZ J
QFSHD0001AWZZ J
QLUGP0001AWZZ J
BC
AC
AA
AD
AP
AH
AE
AK
AF
Tape Mechanism Ass’y
Bracket,PWB Suport
Nylon Band
Bushing,AC Power Supply Cord
Chassis,Main
Dust Sheet
AM AC Power Supply Cord
AC
AB
AC
Edge Light Sheet
Shield Sheet,Power PWB
Shield Sheet,Main PWB
Lead Wire with Lug
Holder,Fuse
Lug (LG1~4)
– 5 –
NO.
PART CODE
PRICE
RANK
DESCRIPTION
611
612
613
614
615
616
617
618
606
607
608
609
610
232
602
603
604
605
92LNBAND1318A J AA Nylon Band,80mm
LX-JZ0037AWFD J AA Screw,ø3
×
10mm
LX-JZ0022AFFD J AA Screw,ø3
×
10mm
LX-JZ0036AWFD J AB Screw,Special
LX-JZ0037AWFD J AB Screw,ø3
×
12mm
LX-LZ0002AW00 J AC Snap Rivet,Main PWB
LX-LZA003AWZZ J AC Snap Rivet,Power PWB
XBBSD20P04000 J AA Screw,ø2
×
4mm
XEBSD26P08000 J AA Screw,ø2.6
×
8mm
XEBSD30P10000 J AA Screw,ø3
×
10mm
XESSD30P10000 J AA Screw,ø3
×
10mm
XHBSD30P06000 J AA Screw,ø3
×
6mm
XHBSD40P06000 J AA Screw,ø4
×
6mm
XJBSD30P08000 J AA Screw,ø3
×
8mm
XJBSD30P10000 J AA Screw,ø3
×
10mm
XJBSF30P08000 J AA Screw,ø3
×
8mm
XJSSD30P10000 J AA Screw,ø3
×
10mm
92LNBAND1318A J AA Nylon Band,80mm
SPEAKER BOX PARTS
901
902
903
904
905
906
907
908
SP1,2
SP3,4
GBOXSA012AWSA J BH Speaker Box Ass’y
CWAKPA002AW01 J AS Net Frame Ass’y
HPNLSA010AWSA J AT Front Panel
LHLDZ8002AWSA J AG Catching Holder
PCUSG0147AWZZ J AC Cushion,Foot
TSPC-A014AWZZ J AC Label,Specification
XMTZD35P14000 J Screw,ø3.5
×
14mm
XMBZD35P16000 J Screw,ø3.5
×
16mm
RSP-ZA009AWZZ J AZ Woofer
RSP-ZA010AWZZ J AR Tweeter
PACKING PARTS
92LBAG1460C1 J AB Polyethylene Bag,Accessories
SPAKAA011AWZZ J AL Packing Add.,Unit,Left/Right
SPAKCA058AWZZ J Packing Case
SSAKH0094AWZZ J AE Polyethylene Bag,Unit
SPAKAA015AWZZ J Packing,Add.,Front
Speaker,Top/Bottom
SPAKZA012AWZZ J AD Sheet,Speaker
SSAKH0099AWZZ J AD Polyethylene Bag,Speaker
ACCESSORIES
92LFANT1746A J AD FM Antenna
QANTL0005AWZZ J AG AM Loop Antenna
RRMCG0408AWSA J AS Remote Control
GFTAB1049AWSA J AE Battery Lid,Remote Control
TINSEA003AWZZ J AG Operation Manual [For U.S.A.]
TINSKA001AWZZ J Operation Manual
[Except for U.S.A.]
TINSZA006AWZZ J AC Quic Guide [For U.S.A. Only]
P.W.B. ASSEMBLY (Not Replacement Item)
1
PWB-A1~3
PWB-B1~4
PWB-C
PWB-D
PWB-E
PWB-F
92LPWB5609MANS J –– Main/Power/Terminal
92LPWB5609DPLS J –– Display/Switch/Led/Jack
92LPWB5609TUNS J –– Tuner
92LPWB5529CDUS J –– CD Servo
QPWBF0027AWZZ J AD CD Motor (PWB Only)
QPWBF1055AWZZ J AE CD Changer Motor (PWB Only)
OTHER SERVICE PARTS
UDSKA0004AFZZ J AZ CD Optical Pickup Lens Cleaner
Disc
– 6 –
XL-HP505
XL-HP505
A
B
C
306-1
306-2
306
306-3
701
304
704
701
302
301
D
703x2
E
M1A
F
307
M2A
308
305x2
G
SW4
H
1 2
PWB-D
3 4
Figure 7 CD MECHANISM EXPLODED VIEW
– 7 –
5 6
XL-HP505
122
A
B
C
D
E
F
G
102x5
101x2 107
116
109
109-2
109-3
101x3
115
803x4
123 109-5
109-4
803x2 109-1
114
108
135
104
106
CD
MECHANISM
UNIT 112
111
124
136
139
119
144
802x4
120
110
103
138
126
125
132
141 140 127
133
143
134
149
150
118
142 129
152
128
152
117
137
151
121
130
148
131
146
145
147
105
113
136
804
148 147
146
145
801x2
SW2
SW3
SW1
SW4
803
M2
803
M1
PWB-F
H
1 2 3 4
Figure 8 CD CHANGER MECHANISM EXPLODED VIEW
– 8 –
5 6
XL-HP505
CD CHANGER
MECHANISM UNIT
614x5
204
A
B
C
D
E
F
G
614
205x5
614x2
CAUTION : RING SPRING ASSY.INTO
FAN POSITION.
OK
RING GAP
NG
RING GAP
218
614
FAN RIB FAN RIB
CAUTION : MUST VISUAL CHECK
AFTER FULLY INSERTED THE FAN TO
MOTOR.
( FOR REFERENCE ONLY )
GAP IS 4.9 mm BETWEEN FAN AND FAN
MOTOR BRACKET.
610x2
610x2
223
610x3
609x2
FAN BLADE
FAN MOTOR BRACKET.
BELT CONNECTION
FF/REW
Clutch
FF/REW
Belt
Main
Belt Motor
PWB-D
219
PWB-B1
610x2
224
Flywheel
Flywheel
PWB-B4
603
609x6
PWB-B3
B
611x4
A
213
226
PWB-B2
606
PWB-C
614
201 201-13
201-2
201-17
201-4
201-1
616x2
201-8
201-12
201-18x2
201-19
602x2
609
229
A
201-10
201-11
212
203
201-7
201-6
201-9
201-5
201-14
201-3
201-16
201-15
201-21
B
229
PWB-A1
201-20
201-22
604
608x2
202
202-4
617x2
220x2
202-2
202-1
231x2
Silicon
Grease
605x2
202-3
(M971)
614
214
211
214
614
PWB-A3
231x2
612
221
614x2 230x4
228
216
614x2
612
225
615x2
614x9
210
613x4
230x6
PWB-A2
607
220x2
215
232
201-23 217
H
Note: Only the unit and consumable parts are supplied as parts supply for the Tape mechanism.
1 2 3 4
Figure 9 CABINET EXPLODED VIEW
– 9 –
5 6
A
B
904x2
908x2
903
C
901
XL-HP505
TWEETER
SP3(L-CH)
SP4(R-CH)
BK
Capacitor
BLUE
BK
RED
BK
WOOFER
SP1(L-CH)
SP2(R-CH)
906
F
D
E
G
902
904x2
908x2
907x2
SP3, SP4
907x2
SP1, SP2
TWEETER
SP3(L-CH)
SP4(R-CH)
WOOFER
SP1(L-CH)
SP2(R-CH)
Capacitor
2.7
µ
F,100V
H
1 2 3 4
Figure 10 SPEAKER EXPLODED VIEW
– 10 –
5
905x4
6
XL-HP505
PACKING METHOD (FOR U.S.A. ONLY)
Setting position of switches and knobs
Tape Mechanism STOP
UNIT Front Speaker(L/R)
Polyethylene Bag,Unit
SSAKH0094AWZZ
Polyethylene Bag,Speaker
SSAKH0099AWZZ
Packing,Add.,
Front Speaker,Top/Bottom
SPAKAA015AWZZ
Label,Energy Star
TLABZ0593AWZZ
Packing Add.,Unit,Left/Right
SPAKAA011AWZZ
Bottom
Label,Pop
TLABZA024AWZZ
FM Antenna
AM Loop
Antenna
Polyethylene Bag,Accessories
92LBAG1460C1
Remote Control
Operation Manual
Quic Guide
A
Sheet,Speaker
SPAKZA012AWZZ
B
B
A
Packing Case
SPAKCA015AWZZ
: Not Replacement Item
– 11 –
— M E M O —
XL-HP505
– 12 –
XL-HP505
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Audio Systems Division
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A041-1447SS•HA•M
SC•SL
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project