Samsung SR-608EV Service manual

REFRIGERATOR
Model : SR-608EV
Model : SR-648EV
SR-688EV
SERVICE
Manual
REFRIGERATOR
CONTENTS
1. Safety Precautions And Warnings
2. Product Specifications
3. Electrical Part Specifications & Standard
4. Electric Diagram
5. Outer Package Specification
6. Air Circulation Route
7. Functions And Directions
8. Circuit Operating Theory
"A"
9. Failure Diagnosis And Repairment
10. Disassemble & Assemble Drawing And
Part Lists
11. Disassemble & Assemble Method
12. Packing Method
“A”: WITH DISPENSER
SR-608EV
SR-648EV
SR-688EV
WITHOUT DISPENSER
SR-606EV
SR-646EV
SR-686EV
13. PCB Diagram
14. PCB Specifications
15. Main Components Specifacations
1. Safety precautions and warnings
Read all instructions before using this appliance in order to aboid risk of accident or possible damage.
Warning/Caution
Description of symbols
Indicates prohibition
This symbol is intended to
Warning alert the user to the
possible death or injury.
Do not disassemble
Do not contant
Caution
This symbol is intended to
alart the user to the
possible injury or damage.
Adhere the instruction strictly
Unplug from the electrical outlet
Earth the appliance to avoid the
risk of an electric shock
Warning
Do not plug multiple
electrical appliances into
the same outlet.
• This may cause abnormal
heating or a fire hazard.
Prohibition
Check the operating
environment.
• Do not install the refrigerator in a
hurnid (with condensation) location
or on an unstable surface.
Do not attempt to make
repairs yourself.
Make sure the power cord is
not crushed or damaged.
• This could lead to fire hazard or
abnormal operation causing
severe personal injury.
• Repair immediately all power cords or
otherwise damaged.
Do not disassemble
Do not attempt to make
repairs yourself.
• This could lead to fire hazard or
abnormal operation causing
severe personal injury.
Earth
Samsung Electronics
outlets that have become frayed or
Make sure the power cord is
not crushed or damaged.
• Repair immediately all power cords or
outlets that have become frayed or
otherwise damaged.
Unplug
1
Caution
Do not store bottled food
or drinks in the freezer
compartment.
• Bottles may explode
causing personal injury.
Prohibition
Do not put anything on top
of the refrigerator.
• Opening or closing the door
may trigger loose items to
slip and cause injury.
Do not store food in an
unstable manner.
• Opening the door may
trigger loose items to slip
and cause injury.
Prohibition
Do not store anything other
than food in the refrigerator.
• Medical supplies which need
to be under strict temperature
control should not be stored in
the refrigerator.
Prohibition
When replacing electric
components, be sure to
use rated components.
• Check the model, rated
voltage, rated current,
operating temperature etc.
of the component.
When servicing the refrigerator,
completely remove dust or
foreign substances from the
housing, electric connections
and etc.
• This can protect against the risk of fire hazard
caused by tracking and short circuit.
After servicing the refrigerator,
be sure to check the
components are reassembled
in a correct manner.
Check the electrical parts for the
trace of moisture penetration.
Prohibition
When servicing the refrigerator,
completely remove dust or foreign
substances from the housing,
electric connections and etc.
• This can protect against the risk
of fire hazard caused by
tracking and short circuit.
2
• The serviced unit should be
reassembled and returned to its original
assembly state.
• When the trace of moisture
penetration is detected, replace
the part or try insulation tapping.
Samsung Electronics
6. Air circulation route
Freezer
Freezer cooling fan
Special
Freezer cooling device
Refrigerator cooling fan
Refrigerator cooling device
Vegetable
Refrigerator
Swing fan
Samsung Electronics
7
2. Product Specifications
ITEM
STANDARD
Model Name
SR-606EV SR-608EV SR-646EV SR-648EV SR-686EV SR-688EV
Total
504
499
544
538
581
575
Freezer
153
153
165
165
165
165
Refrigerator
351
346
379
373
416
410
Net Capacity
(l /CU.FT)
Net dimension (WxHxD)
840X726X1753.5
840X726X1803.5
840X726X1847.5
Regular Frequency
115/60, 127/60, 240/50. 220/50,60
Electric Metor Regular Power
165W
Electric Heating Equipment power
378W
Sort of Refrigerator
Occassional cooling type refrigerator
Cooling Mass
HFC-134a
Cooling Mass Sealed Quanlty
155gr
(4 STAR)
Freezer performance
105kg
Net weight
106kg
106kg
107kg
108kg
109kg
3. Electrical part specifications & standard
STANDARD
ITEM
Temperature
Refrigeration Cycle
Model
Compressor
Starting type
Evaporator
SK182C-L2W SK182P-L2W SK190H-L2U SK190Q-L2U
CSR
CSR
RSCR
RSCR
Oil charge
Freol α-15C(ESTER)/265CC
Freezer
Split Fin Type
Refrigerator
Split Fin Type
Condenser
Forced & Natural Convection Type
Dryer
Molecular Sieve XH-9
Capilary tube
0.82 X 2500 4.26kg/cm2
Refrigerant
HFC-134a/155gr
Type
Freezer
Samsung Electronics
ON(˚C)
OFF(˚C)
High
–20˚C
–22˚C
Mid
–17˚C
–19.0˚C
Low
–14˚C
–16˚C
3
7. Function and Directions
7-1 The outer size
a
b
8
Model
A
B
C
D
Remark
SR-606EA
1066.5
580
1736.5
1753.5
‘a’ applied
SR-608EA
1066.5
580
1736.5
1753.5
‘b’ applied
SR-646EA
1096.5
600
1766.5
1803.5
‘a’ applied
SR-648EA
1096.5
600
1766.5
1803.5
‘b’ applied
SR-686EA
1140.5
600
1810.5
1847.5
‘a’ applied
SR-688EA
1140.5
600
1810.5
1847.5
‘b’ applied
Samsung Electronics
7-2 The name of each parts and disassemble method
• Push to direction
Freezer shelf
• Up the front of shelf to direction
pull and apart to direction 2 .
1
1
and apart to direction
2.
then
2
1
1
2
Chilled room shelf
• Pull to the arrow direction
then up and apart at the
locking point.
• Up and apart as showed.
(concerned model : SR5066/5466/5866)
Shelf REF.
Vegetable box and cover
• Pull with both hands as showed.
• The height can be adjusted according to the
stored bowls.
• Up the cover and apart then pull out the
vegetable box at the mid-point and up and
and pull to apart.
Samsung Electronics
9
7-3 Freezing cycle
COMPRESSOR → SUB CONDENSER → CLUSTER PIPE → HOT PIPE → DRYER →CAPILLARY
TUBE →REFRIGERATOR EVAPORATOR → FREEZER EVAPORATOR → A C C U M U L A T O R
→SUCTION PIPE → COMPRESSOR
10
Samsung Electronics
7-4 PANEL display
QUICK REF.
LO
QUICK REF.
LO
REF.
CONTROL
FRE
CONTROL
DOOR DOOR QUICK
ALARM FREE FRE.
HI
QUICK HI-MOISTURE
FRE.
HI
FRE, CONTROL
7-5 Temperature control
1) Freezer temperature control
1. It consists of five steps as follows and selected by one button.
Mid Æ Mid.High Æ High Æ Low Æ Low.Mid
2. It is circulated and displayed one by one by pressing the button.
3. At first power on it is selected ”Mid”
Category
Initial power on Pressed once Pressed twice Pressed 3 times Pressed 4 times Remark
Indicator Lamp
Mid
Mid·High
High
Low
Low·Mid
Reference Temp.
–18˚C
–19.5˚C
–21˚C
–15˚C
–16.5˚C
2) Temperature control in the refrigerating compartment
1) Select the 5 stages of ‘Mid’–‘Mid · High’–‘High’–‘Low’–‘Low · Mid’ with a button.
2) Whenever the temperature control button of refrigerator is pressed, it continues of light from
‘Mid’–‘Mid · High’–‘High’–‘Low’–‘Low · Mid’.
3) When power turns on “Mid” is automatically selected.
Category
Initial power on Pressed once
Pressed twice Pressed 3 times Pressed 4 times Remark
Indicator Lamp
Mid
Mid·High
High
Low
Low·Mid
Reference Temp.
3˚C
1˚C
–1˚C
6˚C
4.5˚C
Samsung Electronics
11
7-6. Power freeze and Power
• Selected by additional quick freeze & refrigeration button.
• The lamp of quick freeze and refrigeration circulated everytime it pushed.
• No change of setting temperature occured during quick freeze and refrigeration selected.
• Temperature of freezer and refrigerator can be re-setted while quick freeze and refrigeration operates.
1) Quick freeze
(1)Comp. and F-fan runs continuously for two and a half hours when quick freeze selected. ( one
minute after selection )
(2) During quick freezing the refrigerator controlled by setted notch.
2) Quick refrigeration
(1) Comp. and R-fan runs until the temperature of refrigerator reaches -4˚C when quick refrigeration
selected.
(2) After the temperature reaches -4˚C the ’HIGH’ notch runs for an hour and finish quick
refrigeration.
(3) Unless the temperature of refrigerator reaches -4˚C within two and a half hours quick
refrigeration stopped.
3) When quick freeze and refrigeration selected at the same time
(1) Each function applied at the same time. Quick freeze runs Comp. and F-fan for two and a half
hours and quick refrigeration runs Comp. and R-fan for two and a half hours with no relation of
each other.
7-7 Alarming
1) Button touch (”Ding-Dong” sound)
(1)Everytime the button pushed, the input confirmation, ”Ding-Dong”, sounds.
(2) Not sounds, if two keys are pushed at the same time or wrongly handled.
2) Door-Open warning (”Ding-Dong” sound)
(1)Two minutes after door opened, ten times of alarming sounds.
(2) If door opened continuously, ten times of alarming sounds with one minute cycle.
(3)Alarming stopped just after door closed.
3) Forced operating and defrosting (”Beep” sound)
(1) If forced function selected the ”beep” sounds.
(2) Alarming sounds untill the forced operating canceled by automatically ( 24Hr ) or manualy.
(3) Alarming sounds untill the forced defrosting canceled by automatically ( 24Hr ) or manualy.
12
Samsung Electronics
7-8 Defrosting
1) From the first power on, defrosting started after 4 hours of total Comp on time.
2) After that defrosting cycle can be varied from 6 hours to 32hours. (Comp on time)
7-9 Testing
• Testing is for PCB, product, function and service.
• After testing, turn the power on to start self diagnosis.
1) Forced operating
(1) As the button on PCB pushed once, Comp starts immediately without 5 minutes delay.
(2)If forced operating selected the notch of freezer and refrigerator fixed to ”HIGH” and ”MIDHIGH”. Then Comp and F-fan is controlled to pull-down and R-fan is controlled to ”MID-HIGH”
notch.
(3) Pull-down maintained just for 24 hours during forced operating, after that automatically defrost
freezer and refrigerator and then starts normal operating.
(4) Turn the power off or select test cancel mode to cancel the forced operating.
(5)Alarming (0.25 sec on/0.75 sec off) continues until the forced operating finished. It continues
without any relations to alarming key selection or cancel.
2) Forced defrosting
(1) Push the test button one more time to run the forced defrosting of refrigerator.
(2) One more push in the above status will run defrosting of freezer and refrigerator simultaneously.
(3) Forced operating cancelled automatically by starting foced defrosting and return to normal
operating after completion of defrosting.
3) Test cancel mode
(1) One more push in the status of forced defrosting of F/R will run normal operating.
(2) Alarming stopped in the test cancel mode.
7-10 Self diagnosis
1) Self diagnosis at first power on
(1) As the power applied to the refrigerator first time, all displays show and run the self diagnosis.
(2) If no problems founded display returns to normal model.
(3) If problem is founded, on and off the related display lamp and start alarming.
(4) Lamp displayed until the problem solved or self diagnosis cancelled.
(5) After problem solved the display mode return to normal.
Samsung Electronics
13
(6) When refrigerator repaired, sure to power off and on to run self diagnosis.
(7) Refer to belows for problems and related displays.
No
Item
Display LED
Symptom
Remark
1
R1-Sensor
Refrigerator “Low”
• R-room left sensor housing
disconnection.
• Faulty connection.
• Wire open or short.
• Faulty sensor.
R1-Sensor temperature is
over +50˚C or below –50˚C.
2
R2-Sensor
Refrigerator
“Low · Mid”
• R-room left right sensor
housing disconnection.
• Faulty connection.
• Wire open or short.
• Faulty sensor.
R2-Sensor temperature is
over +50˚C or below –50˚C.
3
RD-Sensor
Refrigerator “Mid”
• R-room defrost sensor
housing disconnection.
• Faulty connection.
• Wire open or short.
• Faulty sensor.
RD-Sensor temperature is
over +50˚C or below –50˚C.
4
Room-Temp. Freezer “Low”
Sensor
• Room-Temp sensor housing
disconnection.
• Faulty connection.
• Wire open or short.
• Faulty sensor.
Room-Temp Sensor
temperature is over +50˚C
or below –50˚C.
5
F-Sensor
Freezer “Low”
• F-room sensor housing
disconnection.
• Faulty connection
• Wire open or short.
• Faulty sensor.
F-Sensor temperature is
over +50˚C or below –50˚C.
6
FD-Sensor
Freezer “Mid”
• R-room defrost sensor
housing disconnection.
• Faulty connection.
• Wire open or short.
• Faulty sensor.
F-Sensor temperature is
over +50˚C or below –50˚C.
7
GearedMotor
Refrigerator “High”
• Faulty geared-motor
• Faulty reed-switch
housing disconnection.
• Faulty connection.
Square wave not detected
by reed-S/W.
(Self-diagnosis Display Table)
14
Samsung Electronics
7-11 Load status display
1) Press power F/R key for five seconds then press temperature control key in the refrigerator after
temperature display lamps on and off three times.
2) This mode shows which load is being sourced signal from MICOM currently. This doesn’ t mean
the load is operating but just show MICOM signal output. The Compressor may not operate due
to the open wire or relay missing though the display shows the Compressor operating.
3) Load status display return to normal mode after sixty seconds.
4) Follows are load status and related display.
No
Display LED
Item
Display
Remark
Freezer Subordinate
1
COMP
Freezer “Low”
Relevant LED ON during
Compressor operation
2
F-FAN
Freezer “Low · Mid”
Relevant LED ON during F-FAN
operation
3
Freezer defrost Heater
Freezer “Mid”
Relevant LED ON during freezer
defrost heater on
4
Freezer bulb
Freezer “Mid · High”
Relevant LED ON during freezer
bulb ON
5
COMP. Cooling Fan
Freezer “High”
Relevant LED ON during
Compressor Cooling Fan oeration
Refrigerator Subordinate
6
R-FAN
Refrigerator
“Low · Mid”
Relevant LED ON during F-FAN
operation
7
Refrigerator defrost
Heater
Refrigerator “Mid”
Relevant LED ON during
refrigerator defrost
8
Refrigerator bulb
Refrigerator
“Mid · High”
Relevant LED ON during
refrigerator bulb ON
9
GEARED-Motor
Refrigerator “High”
Relevant LED ON during
refrigerator brade rotation
Mode Display
10
Initial Mode
Quick Freezing
Relevant LED ON with initial
power input
11
Overload
Quick Refrigeration
Relevant LED ON when ROOM
temperature is over 35˚C
12
Low temp.
High humidity
refrigeration
Relevant LED On when ROOM
temperature is below 20˚C
(Load Status Display Table)
Samsung Electronics
15
11. Disassemble and assemble method
11-1 Refrigerator inside lamp replacement
1) Remove the screw with (+) driver and
push the cover to the arrow direction and
apart.
2) Remove out the lamp to the arrow direction
and replace with new one. ( Left & Right )
3) Insert the front of the cover first and screw
it.
11-2 Freezer inside lamp replacement
• Grab the the salient part of cover and pull
it down to apart. Replace the 220V/15W
lamp and insert front of cover first and
then fix it.
Samsung Electronics
41
11-3 Disassemble of refrigerator cooling part
1) Remove foods and shelves inside the
refrigerator.
2) Pull out the chilled room box to the arrow
direction and pul it up to apart at the locking
point.
3) Push the right arrow part of the chilled room
inside and apart the chilled room cover.
4) Up the cover of vegetable box and pull apart
then pull it out.
5) Remove the screws with (-) driver.
2 screws
6) Release the locking part using (-) driver as
shown.
7) Pull out the cover front part.
42
Samsung Electronics
8) Disassemble the wire housing of motor in the
center.
9) Pull the housing part and disassemble the wire
terminal.
10) Remove screws of duct and pull apart.
Remove 2
screws
11) Release wire terminal on top of the left.
12) Remove screws of evap. Cover rear and release
the locking part of both left and right using (-)
driver.
latch
Remove 2 screws
Samsung Electronics
43
♦ Cooling cycle unit assembly in the refrigerating compartment
(Groove for preventing
small ice when
defrosting)
♦ Cooling cycle unit cover assembly in the refrigerating compartment
44
Samsung Electronics
♦ Rotating duct assembly in the refrigerating compartment
Samsung Electronics
45
11-4 Disassemble of cooling part in the freezing room
1) Pull out the shelf.
1
2
2) Remove screws of evap cover and pull apart.
3) Disconnect the each terminal of wire housing
on top of the left side.
4) Remove screws of evap. Cover rear and
release the locking point using (-) driver.
Residual spread preventer
46
Samsung Electronics
♦ Assembly of the cooling cycle unit in the freezer
Maintains 45˚
(Coolant & noise
reduction)
Samsung Electronics
47
11-5 Assembling specifications of machinery room
1. remove screws of compressor cover
2. Assembling specifications of machinery room
Noise & Vibration
reduction rubber
48
Samsung Electronics
11-6 Assembling specifications of power supply part
1. Turn off the power of
refrigerator.
2. Remove the cover using (-) driver.
3. Assembling specifications of power supply part
TEST S/W
Condenser
D/C Trans
Samsung Electronics
49
11-7 Disassembling method and order of water dispenser
1. Disassembling method and order of cock part
1-1. Open the door and detach the water tank. Throw away waters in the tank.
1-2. Turn the cock on the bottom of the water tank to counterclockwise and apart.
1-3. Push part 6 to arrow direction and apart part 2 then part 5,6 automatically aparted. Puch the
locking point to arrow direcion to apart part 3.
1) Be careful not to damage the parts 1,2,5,7 ( It may cause a leak of water. )
2) Assembling is reverse of the disassembling order.
part 2
part 3
part 7
part 1
part 5
part 4
part 6
2. Disassembling method and order of lever
2-1. Close the door and turn the screw of the bottom of cover dispenser to counterclockwise using (+)
driver and pull out to arrow direction and apart the cover.
2-2. Release locking point of lever dispensor using (-) driver to the arrow direction and apart spring
and lever dispenser.
2-3. Push locking point using (-) driver and pull out key-lock to upside then apart dispenser locking
device.
2-4. Assembling is reverse of the disassembling order after inserting the spring to lever shaft.
50
Samsung Electronics
11-8 The operating theory and order of water dispenser
1. Push the knob lever(1-1) to the arrow direction.
2. Lever dispenser(1-2) rotates around spring-lever(13) to the counterclockwise and push guide pin(2-1)
and press the spring dispenser(2-2) vertically.
3. O-ring(big)(2-4) inserted in guide-push(2-3) moves
vertically and aparts from cock-dispenser(2-5) then
water flows through path of guide-pin(2-1) to the
cup.
4. O-ring(small)(2-6) inserted in guide-pin(2-1) also
aparts from guide-push(2-3) to let air go through
that helps water flowing.
5. Stop pushing knob lever(1-1) when water filled to
certain point.
6. Lever-dispenser returns by expansive force of
spring-dispenser(2-2) and spring-lever(1-3) .
7. Guide-push(2-2), guide-pin(2-1), o-ring(small)(2-6)
and o-ring(big)(2-4) also retun and contact cockdispenser(2-5) then return to initial state.
WATER-DISPENSER
2-7
Samsung Electronics
51
11-9 Dispenser unit list
NO
CODE-NO
PART
1
DA63-10905C
ASS’Y-COVER DISPENSER
M-PROJECT
1
1-1
DA64-40173B
KNOB(LEVER)
ABS
1
1-2
DA32-10105G
LEVER-DISPENSER
POM(TP-20)
1
1-3
DA61-20146A
SPRING(LEVER)
STS-304(WPB)
1
1-4
DA64-90138B
KEY(LEVER)
ABS(HG-0760)
1
1-5
DA64-10896B
COVER-DISPENSER
ABS(HG-0760)
1
2
DA64-90136A
TANK-WATER ASS’Y
M-PROJECT
1
2-1
DA71-70158A
GUIDE-PIN
PC
1
2-2
DA61-20147A
SPRING-DISPENSER
STS-304(WPB)
1
2-3
DA71-70159A
GUIDE-PUSH
PC
1
2-4
DA60-90103B
RING-O
SILICON(TSE-221)
1
2-5
DA67-10402A
COCK-DISPENSER
PC-ABS
1
2-6
DA60-90103A
RING-O
SILICON(TSE-221)
1
2-7
DA74-40142A
VALVE(WATER-TANK)
SILICON(TSE-221)
1
2-8
DA71-20159A
FIXER-FILTER
PE(HARD)
1
2-9
DA67-30214A
CAP-TANK UPP
PE( SEMI-HARD)
1
2-10
DA74-90115B
TANK-WATER
ABS(INSERT)
1
2-11
DA63-30011A
GASKET-COMP V/PLATE
SILICON(TSE-221)
1
2-12
DA63-10383A
COVER TANK
ABS, WHT
1
2-13
DA65-20004A
CLAMP-TANK
PC ABS
2
2-14
DA67-30005A
CAP
ABS
1
PART USED INSTEAD
3
DA67-10403B
CASE-DISPENSER
ABS
1
A/S IMPOSSIBLE
3-1
DA71-20264A
FIXER-CASE
ABS
1
A/S IMPOSSIBLE
3-2
DA74-40144A
VALVE(FIXER-CASE)
SILICON(TSE-221)
1
A/S IMPOSSIBLE
3-3
DA02-10143A
TAPE-AL, FOIL(B)
AL(T=0.075)
1
A/S IMPOSSIBLE
3-4
DA02-10142A
TAPE-AL, FOIL(A)
AL(T=0.075)
1
A/S IMPOSSIBLE
3-5
DA02-10014A
TAPE-AL
TAPE AL, T0.05, W50, 1RL
0.32MT
A/S IMPOSSIBLE
4
DA63-10010A
COVER-DISPENSER, B
ABS
1
5
DA67-40295B
TRAY-DISPENSER, A
ABS
1
6
DA67-40294B
TRAY-DISPENSER, B
ABS
1
7
DA63-20158C
GUARD-VARIETY, A
GPPS
1
8
6002-000213
SCREW-TAP
TH1 4X12 FZ-FZY
2
SPEC.
Q’TY
REMARK
OF WATER TANK
52
Samsung Electronics
11-10 General diagnosis of water dispenser
No water or too little water flow out
Check the water in the water tank
Fill in the water tank
Normal
Normal
Check the fixed state of water tank
( If the fixed state is bad the guide-pin doesn’ t work due to the
wrongly positioned cock-ass’ y)
Normal
Fix the water tank correctly ( Check guide-variety )
Water falls continueously
Check the contact state of o-ring ( burr, eveness, etc)
(It acn cause a leak of water.)
Normal
If gasket is missed or wrongly assembled, then fix the problem.
Check the gasket between cock-ass’ y and water tank
(Misse valve(water tank) cause a leak of water between cock-ass’ y and
water tank. )
If valve(water tank) is missed or wrongly assembled,
then fix the problem.
Normal
Change all the parts
Normal
Change refrigerator door
Samsung Electronics
53
8. Circuit operating theory
8-1 Power supply part
Circuit used
Voltage
(DC 12V)
Relay Operation
Vcc (DC 5V)
Power around MICOM & Sensor Detector
V12 (DC 12V)
LED Display & S/W Detector
Secondary voltage output of DC trans is sourced 1~3 and 5~7 about 15V. On the ’a’ part, input is
rectified and regulated by MC 7812 and is about DC12V. This voltage is applied for relay running and
regulated again by 7805 to transformer. DC 5V is applied to display part after rectified and regulated by
MC7812.
8-2 Resetpart
KA7533
+
16
29
RESET
Reset part is intialize RAM of MICOM and others when
power is on or power is interrupted for some time. It
will make whole program runs from the first status.
When power is supplied, reset voltage is ”low” status
for a few seconds and turn into ”High” status in the
normal operating.
Samsung Electronics
8-3 Door S/W sensing part
DOOR
F
R
Door Conditions
Door S/W Contact
CLOSE
CLOSE
OPEN
OPEN
CLOSE
CLOSE
OPEN
OPEN
CON06
PIN NO
Micom Input Voltage
“HIGH”
1
“LOW”
“HIGH”
3
“LOW”
1) When the door is opened, the door S/W closed and MICOM input is ‘Low’.
Then the door-open is sensed.
2) When the door is closed, the door S/W is opened and MICOM input is ‘high’.
Then the door closed is sensed.
8-4 “V” motor, location sensing part ( Reed S/W)
1) “V” motor’s location sensing which is for G.A. fuzzy control is done by reed S/W.
2) There occure a “high” to “Low” and “Low” to “High” conversion period on con02 pin6 by the
motion of swing fan. “V” motor’s location is detected by it
Samsung Electronics
17
8-5. Temp. sensing part
(Room Temp Sensor)
When Sensor is opened
When sensor is cut off
MICOM input “HIGH”
MICOM input “LOW”
1) Thermistor is used for sensing which has negative resistance coffiecient to the temperature.
2) MICOM input voltage, VF of sensor is VF=
RTH
xVcc
RTH + R24
( Vcc: 5V, Rth : Sensor resistance )
3) Refer to conversion table for VF and RTH according to temperature.
18
Samsung Electronics
8-6 Comp and defrosting heater operating
As it is seen above block diagram, 220V line is connected to the commons of Comp relay, Ry78 and
defrosting heater relay, Ry77, Ry71. When those relays are off state Comp and defrosting heater are also
off. As Comp relay moves to on and AC 220V applied to Comp load it starts operating. On the other
hand defrost heater runs if defrost heater relay moves to on. There is no chance that both Comp and
defrost heater runs together so it’s useful for safety aspect.
RELAY
Load
Remark
OFF
Comp Operation
Defrost-Heater Power Off
ON
OFF
Comp off, Defrost-Heater Off
ON
OFF
Defrost-Heater On
ON
OFF
Comp Off, Defrost-Heater Off
COMP
Defrost H
ON
Samsung Electronics
Comp Power Off
19
9. Failure diagnosis and repairment
Main PCB check
• Turn the power off and on again for self diagnosis check.
• Refer to belows for error code table
♦ Error code table
Item
Display “LOW” “LOW.Mid”
“Mid”
“Mid.HIGH”
“LOW”
Refrigerator
R1 sensor
R2 sensor
R Defro. sensor
–
Swing fan motor
Freezer
Room Temp sensor
F sensor
F Defro. sensor
–
–
V(v)
T(˚C) R(ohm)
CONTROL BOX
Room TEMP-Sensor
F Sensor
F Defro. Sensor
Freezer
R1 Sensor
R Defro. Sensor
Refrigerator
R2 Sensor
♦ Table for Vf and Rth according to temperature
T(˚C) R(ohm)
-35
-34
-33
-32
-31
-30
-29
-28
-27
-26
-25
-24
-23
-22
-21
-20
-19
20
68648
65011
61595
58384
55366
52526
49854
47337
44967
42733
40626
38640
36765
34995
33323
31743
30250
V(v)
4.364
4.333
4.301
4.268
4.235
4.200
4.164
4.127
4.090
4.051
4.012
3.972
3.930
3.888
3.845
3.802
3.757
T(˚C) R(ohm)
-18
-17
-16
-15
-14
-13
-12
-11
-10
-9
-8
-7
-6
-5
-4
-3
-2
28838
27502
26237
25040
23906
22832
21814
20848
19932
19062
18237
17453
16709
16001
15328
14688
14080
V(v)
3.712
3.666
3.620
3.573
3.525
3.477
3.428
3.379
3.329
3.279
3.229
3.178
3.127
3.076
3.025
2.974
2.923
T(˚C) R(ohm)
-1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
14051
12949
12424
11924
11447
10993
10559
10146
9752
9375
9016
8673
8345
8032
7732
7446
7172
2.872
2.821
2.770
2.719
2.668
2.618
2.567
2.518
2.468
2.419
2.370
2.322
2.274
2.227
2.180
2.134
2.088
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
6910
6659
6420
6190
5970
5759
5557
5363
5178
5000
4829
4665
4508
4357
4212
V(v)
2.043
1.998
1.954
1.911
1.869
1.828
1.786
1.745
1.705
1.666
1.628
1.590
1.553
1.517
1.481
Samsung Electronics
Check in advance
1. Check the power of consent and power code.
2. Check it based on the “References” on the next pages.
9-1 No Input Power
Y
N
N
Y
N
Y
Y
N
N
Y
Y
Y
Samsung Electronics
21
9-2 Self diagnosis failure
1) Outer temperature sensor failure
Start
Is main PCB connection
(CON 5) O.K. ?
N
Connection failure
Y
N
Is outertemp sensor O.K.
Change sensor
Y
Is input vltg of CON 05
pin2 O.K.
N
Wire open
Change main PCB ass’ y
2) R1, R2, refrigerator temp. sensor failure
Start
Is temp. sensor O.K. ?
N
Change sensor
Y
Is main PCB connection
(CON02) O.K. ?
N
Connection failure
Y
Is input vltg of CON 02
pin1,2 O.K.
N
Connection between sensors open
Y
Is input vltg of CON 02
pin1,2 O.K.
Y
N
Wire open
Change main PCB ass’ y
22
Samsung Electronics
3) Refrigerator’ s defrosting sensor failure
Start
Is main PCB connection
(CON 5) O.K. ?
N
Connection failure
Y
Is defrosting sensor O.K.
N
Change sensor
Y
Is connection of defrosting
sensor O.K.
N
Connection failure
Y
Is input vltg of CON 03
pin4 O.K.
N
Wire open
Y
Change main PCB ass’ y
4) F1, Freezer temp. sensor failure
Start
Is main PCB connection
(CON03) O.K. ?
N
Connection failure
Y
Is temp. sensor O.K.
N
Change sensor
Y
Is connection of temp.
sensor O.K.
N
Connection failure
Y
Is input vltg of CON 03
pin1 O.K.
Y
N
Wire open
Change main PCB ass’ y
Samsung Electronics
23
5) Freezer’ s defrosting sensor failure
Start
N
Is main PCB connection
(CON03) O.K. ?
Connection failure
Y
N
Is defrosting sensor O.K.
Change sensor
Y
Is connection
of defrosting sensor
O.K.
N
Connection failure
Y
Is input vltg of CON 03
pin5 O.K.
Y
N
Wire open
Change main PCB ass’ y
24
Samsung Electronics
9-3 In case of continuous alarming
references
• F/R door open alarms for ten seconds after 2 minutes later. If door opens continuously, door
open alarms for ten seconds with one minute cycle. ( ten times of “Ding-Dong”)
• If there is moisture in door S/W, it is shorted and alarms due to the MICOM’s misjudgement.
In this case the inside lamps of freezer and refrigerator turns off so the lamp do not turns on
though you open the door.
• If the door S/W is rusted, the signal of door open do not reach to MICOM and no alarms and
lamps turned off continuously.
1) In case of “Ding-Dong” alarming
Start
Is main PCB connection
(CON03) O.K. ?
N
Connection failure
Y
Is the door S/W O.K.
N
Change sensor
Y
Is main PCB connection
(CON06) O.K.
N
Connection failure
Y
Does the vltg of CON06
Pin 1,3 change?
Y
N
Wire open, Change door S/W
Change main PCB ass’ y
Samsung Electronics
25
2) In case of “Beep-Beep” alarming
Start
Is forced operating /
frosting selected ?
N
Cancel forced oper./defro.
Y
Is it the same when
power on again?
N
Main PCB O.K.
Y
CON04 shorted. or touched
references
• There is no “beep-beep” alarming except the forced deforst or sensing trouble during self
diagnosis.
• If self diagnosis sensed trouble, it is displayed on the panel PCB, so easy to check. If not , the
forced deforst or forced operation is selected the notch status are “High”-“Mid.High” at that
time.
3) In case of no panel PCB display
Start
Is the connection of
cover O.K. ?
N
Connection failure
Y
Is main PCB connection
(CON07) O.K. ?
N
Re-connection
Y
Is panel PCB
connection O.K. ?
N
Connection failure
Change panel PCB
26
Samsung Electronics
4) In case of the panel PCB key selection is impossible
Start
Is the connection of
cover O.K. ?
N
Connection failure
Y
Is main PCB connection
(CON07) O.K. ?
N
Re-connection
Y
Is panel PCB connection
O.K. ?
N
Connection failure
Y
Are there any keys
already pressed ?
Y
N
Re-assemble panel PCB
Change panel PCB
9-4 In case of fan do not run
references
‘Be sure to check cooling fan under forced operation.’
1. F-fan, R-fan and Comp cooling fan are off when Comp is off.
2. Though the Comp is on, the R-fan is not always on because the fan is off when the temperature
was reached to the set point.
3. There is delaying time to run the fan after door open (Comp on state) . The delay time varys
from ten seconds to one minute. (Forced operation included)
Samsung Electronics
27
9-5 In case of swing fan in the refrigerator doesn’ trun.
Start
Does it run for
30 seconds when the
door open?
Y
Swing fan O.K.
N
Is the door S/W O.K. ?
N
Change door S/W
Y
Is the connection of
CON09 O.K. ?
N
Connection failure
Y
Is the vltg of both ends of
motor 220V
N
Y
Motor failure
Change main PCB ass’ y
references
1. Swing fan doesn’ t run at the off state of R-fan. ( door closed)
2. Swing fan runs for 30 seconds when the door is open but from then it doesn’ t work as the door
opened continuously. It’ s just runs for 30 seconds from the time the door is opened.
28
Samsung Electronics
1) In case of F-fan doesn’ t run
Start
Is it forced operation ?
Forced operation
Y
Does it run 1 min
after the door S/W pressed?
Y
F-fan O.K.
N
Is the connection of
CON10 O.K. ?
N
Re-connection
Y
Is the vltg of both ends of
F-fan 220Vac
Y
F-fan failure
N
Does the door S/W
works normally
Y
N
Change door S/W
Change main PCB ass’ y
Samsung Electronics
29
2) In case of R-fan doesn’ trun
Start
Select forced operation.
Does it run
1 min after the door S/W
pressed?
Y
R-fan O.K.
N
Does the door S/W
works normally
N
Change door S/W
Y
Is the connection of
CON09 O.K. ?
N
Re-connection
Y
Is the vltg of both ends of
F-fan 220Vac
N
Y
F-fan failure
Change main PCB ass’ y
30
Samsung Electronics
10. Disassemble & assemble drawing and part list
10-1 Freezing Compartment
Samsung Electronics
31
NO
CODE-NO
ITEM
SPECIFICATIONS
Q’TY REMARK
DA63-11041B
COVER LAMP FRE ASSY
220V, 240V
1
DA63-11041C
COVER LAMP FRE ASSY
110V, 127V
1
1-1
DA32-10109A
SENSOR FRE
502AT
1
1-2
DA63-11030A
COVER LAMP FRE
MIPS
1
1-3
DA47-40112R
LAMP HOLDER
PBT
1
1-4
4713-000213
LAMP-INCANDESCENT
220V~240V/15W
1
4713-001035
LAMP-INCANDESCENT
110V~127V/15W
1
1-5
6002-000215
SCREW TAP TH
1-4X16FE, FXY
2
2
DA67-20163N
SHELF FRE ASSY
GPPS
1
2-1
DA67-20135D
SHELF FRE
GPPS
1
2-2
DA67-40299A
TRAY ICE
PP
2
2-3
DA64-20194A
TRIM SHELF
PE
4
3
DA63-10403C
CASE ICE
3-1
DA63-10338A
COVER CASE ICE
GPPS
1
3-2
DA67-10205D
CASE ICE CUBE
HIPS
1
DA59-40245B, C, A, D
EVAP-FRE ASSY
110V, 127V, 220V, 240V
1
4-1
DA47-10148D
THERMO FUSE
250V, 10A
1
4-2
DA32-10105G
SENSOR-REF
250V, 10.5A
1
DA63-11044C, D, F, E
COVER-EVAP REAR(FRE)ASSY
110V, 127V, 220V, 240V
1
5-1
DA63-11035A
COVER-EVAP REAR
PP
1
5-2
DA63-10364A
COVER MOTOR FAN
PP
1
5-3
DA31-20103A
FAN
ABS, 120µ
1
5-4
DA31-10109D
MOTOR-FAN
110V, 2650RPM
1
DA31-10109W
MOTOR-FAN
127V, 2650RPM
1
DA31-10109B
MOTOR-FAN
220V, 2650RPM
1
DA31-10109F
MOTOR-FAN
240V, 2650RPM
1
5-5
DA63-40119A
GROMMET FAN MOTOR
NBR
2
5-6
DA61-20128A
SPRING FAN
SUS27WR
1
5-7
DA72-60042A
BUMPON-MOTOR
NBR
1
5-8
6002-000224
SCREW TAP TH
2S 4X16FE, FZY
1
6
6002-000215
SCREW TAP TH
1-4X16FE, FZY
6
7
DA67-30266D
CAP-SCREW
PP
4
8
DA63-10402K
COVER-EVAP FR(FRE)ASSY
PP
1
9
DA47-20208G
HEATER DRAIN
110V/13W
1
DA47-20208H
HEATER DRAIN
127V/13W
1
DA47-20208F
HEATER DRAIN
220V/13W
1
DA47-20208J
HEATER DRAIN
240V/13W
1
1
4
5
32
1
Samsung Electronics
10-2 Refrizerating Compartment
Samsung Electronics
33
NO
CODE-NO
1
1-1
1-2
1-3
2
2-1
2-2
DA59-40238C, E, A, B
DA47-10148D
DA32-10105G
DA63-40001A
DA63-11040D, C
DA63-11031A
4713-000213
4713-001035
DA47-40112T
DA61-70266A
DA02-90106E
DA63-11036A
DA67-40300D
DA66-10104A
DA71-20145A
DA64-20205A
DA64-20204A
DA63-11020D
DA63-10467A
DA32-10105B
DA63-10534L, R, J, K
DA63-10216A
DA63-10364A
DA31-20103A
DA31-0109D, W, B, F
DA61-20128A
DA72-60042A
6002-000224
DA63-40119A
6002-000215
DA72-40484A
DA39-20122E
DA63-10235F
DA67-30266D
6002-000215
DA67-20172B
DA63-10384G
DA63-10237J
DA63-10237E
DA63-10237L
DA63-10237F
DA63-10897E
DA31-20133B
DA31-20135B
DA72-30193A
DA72-60158C
2-3
2-4
3
4
5
5-1
5-2
5-3
5-4
6
7
8
9
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
10
11
11-1
12
13
14
15
16
17
17-1
17-2
17-3
17-4
17-5
34
ITEM
EVAP-REF ASSY
THERMO FUSE
SENSOR-DEF
GROMMET EVAP
COVER-LAMP REF ASSY
COVER LAMP REF
LAMP-INCANDESCENT
LAMP-INCANDESCENT
HOLDER LAMP
SUPT LAMP
CATALYST-LTC
COVER-PURIFIER
TRAY-CHILL ROOM ASSY
ROLLER-FREE
FIXER ROLLER
TRIM TRAY, R
TRIM TRAY, L
COVER-CHILLED ASSY
COVER-SENSOR REF
SENSOR-ASSY
COVER EVAP REAR REF ASSY
COVER EVAP RE, (R)
COVER MOTOR FAN
FAN
FAN-MOTOR
SPRING FAN
BUMPON MOTOR
SCREW TAP TH
GROMMET FAN MOTOR
SCREW TAP TH
INS, COVER EVAP FR
WIRE HARNESS GEARED
COVER EVAP FRONT(REF)
CAP SCREW
SCREW-TAP TH
SHELF-REF ASSY
COVER-VEG ASSY
COVER-DUCT ASSY
COVER-DUCT ASSY
COVER-DUCT ASSY
COVER-DUCT ASSY
COVER-DUCT REF
BLADE AIR LOW
BLADE AIR UPP
SPACER DUCT, REF
SEAL DUCT, REAR
SPECIFICATIONS
110V, 127V, 220V, 240V
250V, 10A
250B, 10.5A
NR
110~127V, 220~240V
SAN
220V~240V/15W
110V~127V/15W
PBT
STS
T15, W40, L70
PP
POM
NY-66
PE
PE
HIPS
502AT
110V, 127V, 220V, 240V
PP
PP
ABS
110V, 127V, 220V, 240V
SUS27WR
NBR
2S 4X12FE, FZY
NBR
1-4X16FE, FZY
PP,WHT
1-4X16FE, FZY
110V~127V
220V~240V
110V~127V
220V~240V
HIPS
ABS
ABS
FOAM-PS
FOAM-PE
Q’TY REMARK
1
1
1
1
1
1
2
2
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
SR-606(8)EV
SR-606(8)EV
SR-646(8)EVSR-686(8)EV
SR-646(8)EVSR-686(8)EV
Samsung Electronics
NO
CODE-NO
17-6
17-7
DA72-60161D
DA31-10107D
DA31-10107E
DA60-40104A
DA31-20132A
DA63-40133A
DA31-20132A
DA63-11024A
DA67-10227F
DA67-10228A
DA66-10104A
DA71-20145A
17-8
17-9
17-10
17-11
17-12
18
18-1
18-2
18-3
Samsung Electronics
DESCRIPTION
SEAL DUCT, AIR
GEARD MOTOR
GEARD MOTOR
WASHER
BLADE-AIR GUIDE
GROMMET MOTOR
BLADE CONNECTING
COVER DUCT, FR
CASE-VEG ASSY
CASE VEG
ROLLER-FRE
FIXER ROLLER
SPECIFICATIONS
PVC-FOAM
AC220V~240V
AC110V~127V
ID 04, T0.5
PP
NBR
HIPS
GPPS
POM
NY-66(PA)
Q’TY REMARK
1
1
1
1
7
1
1
1
1
1
4
4
35
10-3 Cabinet and Unit Compartment
36
Samsung Electronics
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
CODE-NO
DA90-10230P
DA61-40115B
DA61-10145D
DA61-30127B
DA59-50021A
DA59-50033A
DA59-50014A
DA59-50015A
DA34-10003P
DA34-10003P
DA34-10003W
DA34-10003G
DA35-10003H
DA35-10003H
DA35-10003L
DA35-10003N
DA63-10352A
DA32-10105F
DA65-20101A
DA63-40234C
DA34-10122D
DA73-30102A
DA60-10104B
DA60-10110A
DA62-20001C
DA63-40171B
DA67-30218P
DA39-10123
6002-000216
DA71-60123F
DA60-90101A
DA61-40101C
DA66-20112A
DA60-10107A
DA67-40176C
DA31-10110G
DA31-10110L
DA31-10110F
DA31-10110H
DA31-20102A
DA61-20128A
6002-000215
DA73-10314C
2501-001091
2401-000511
2501-000423
DA26-30112A
DA26-30112B
DA26-30110C
DA26-30110A
DA63-10243A
Samsung Electronics
ITEM
ASSY-CABI FOAM
CASTER-FRONT
HINGE-LOW
FOOT-ASSY
COMPRESSOR
COMPRESSOR
COMPRESSOR
COMPRESSOR
O/L PROTECTOR
O/L PROTECTOR
O/L PROTECTOR
O/L PROTECTOR
PTC
PTC
PTC
PTC
COVER-RELAY
SENSOR-ASSY(EXIT)
CLAMP-COMP
GROMMET-COMP
DOOR SWITCH
DRYER
SCREW TAP TITE
SCREW SPECIAL, C
TUBE-PVC
GROMMET-COMP
CAP-SCREW
POWER-CORD
SCREW TAP TITE
CHASSIS COMP ASSY
RIVET CASTER
CASTER REAR
SHAFT COMP
SCREW EARTH
TRAY DRAIN WATER ASSY
MOTOR-CIRCUIT
MOTOR-CIRCUIT
MOTOR-CIRCUIT
MOTOR-CIRCUIT
FAN-SIRRCOO
SPRING-FAN
SCREW TAPPING
PIPE SUB COND ASSY
CAPACITOR
CAPACITOR
CAPACITOR
TRANS-DC
TRANS-DC
TRANS-DC
TRANS-DC
COVER-COMP ASSY
SPECIFICATIONS
PP
SCP1
PP
SK182C-L2W
SK182P-L2W
SK190H-L2U
SK190Q-L2U
4TM444NHBYY-53
4TM444NHBYY-53
4TM314RHBYY-53
4TM232SHBYY-53
PTHAS-T100M200B
PTHAS-T100M200B
PTHAR-T220M350D
PTHAS-T330M385D
PP
STC5, TO.6
NBR, BLK
WHT
CU. OD18.85, L119
SNC3
M5, STS
PVC
NBR
PP
L2500(OPTION)
PH1-4X20
MSWR10, ZPC
PP, NTR
SUM24,ZPC2(YEL)
BSBN, M4X10
110V
127V
220V
240V
ABS, P/120
STS27
TH1-4X16
TO.7, OD4.76, L969
5µF, 350VAC
12µF, 250VAC
125µF, 125VAC
105V/50,60HZ
127V
220V
240V
SECC1
Q’TY REMARK
1
2
1
2
1
1
1
1
2
4
1
1
1
3
2
4
1
1
2
1
2
2
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
37
NO
35
36
37
38
39
40
41
42
43
44
45
38
CODE-NO
DA72-60019A
6002-000213
DA63-11029A
DA67-10105G
DA63-10212H
DA41-20146A
DA41-20105F
DA41-20146B
DA41-20105G
DA61-10205A
DA63-10920G
DA63-50145A
DA61-10146C
DA63-50146A
ITEM
SEAL PAM ABSORB
SCREW TAPPING
COVER LEG, FRONT
CASE CONTROL BASE
COVER-PCB PANEL
ASSY-MAIN PCB
ASSY-MAIN PCB
ASSY-MAIN PCB
ASSY-MAIN PCB
HINGE-UPP
COVER-HINGE UPP
SHIM-HINGE UPP
HINGE-MID ASSY
SHIM-HINGE, LOW
SPECIFICATIONS
T10, W170, L170
TH 4X12FR, FZY
PP
PP-VO
PP
SR-606(8)EV
SR-606(8)EV
SR-646(8), 680(8)EV
SR-646(8), 686(8)EV
SHP1, T3.2
PP
RD-PVC T1.0
SHP1 T4.0
RD-PVC T1.0
Q’TY
REMAR
1
3
1
1
1
1SET
1SET
1SET
1SET
1
1
1
1
1
Samsung Electronics
10-4 Door Parts
Samsung Electronics
39
NO
CODE-NO
DESCRIPTION
1
(1)(2)(3)(4)
DA91-10258L, M, N, P
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE(WITHDISPENSER)
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE(WITHDISPENSER)
ASS’Y FOAM DOOR FRE
ASS’Y FOAM DOOR FRE(WITHDISPENSER)
GASKET DOOR FRE ASS’Y
GASKET DOOR FRE ASS’Y
GUARD FRE
GUARD VARIETY ,A
GUARD VARIETY ,B
GUARD BOTTLE
GUARD REF LOW
STOPPER MID
GROMMET HINGE MID
ASS’Y AUTO CLOSE
STOPPER DOOR MID
STOPPER DOOR,C
SCREW TAP PH
CASE-PCB ASS’Y
CASE-PCB
KNOB TOUTH
KNOB TOUTH
SCREW TAP PH
COVER PCB PANEL
SCREW TAP FH
PCB PANEL ASS’Y
REINF HINGE.REF
TANK-WATER ASS’Y
GUIDE BOTTLE
TRAY EGG,A
TRAY EGG,B
TRAY DISPENSER,B
TRAY DISPENSER,A
COVER DISPENSER ASS’Y
SCREW TAP
SCREW TAP TH
SCREW-PH
SCREW TAP TH
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16-1
16-2
16-3
16-4
16-5
16-6
17
18
19
20
21
22
23
24
25
26
27
28
(1)(2)(3)(4)
DA91-10258Q, R, S, T
DA91-10259M, N, P, Q
DA91-10260H, J, K, L
DA91-10259R, S, T, U
DA91-10260M, N, P, Q
DA91-10259V, W, X, Y
DA91-10259R, S, T, U
DA63-30178N
DA63-30178P
DA63-20160B
DA63-20158A
DA63-20159B
DA63-20162C
DA63-20161C
DA71-40135A
DA63-40118A
DA65-90111H
DA71-40169A
DA63-10894B
DA63-10984B
DA67-10401C
DA64-40135C(L)
DA64-40135C(R)
6002-000466
DA63-10894A
6002-000453
DA41-20156B
DA71-10272B
DA74-90136B
DA71-10272A
DA67-40297A
DA67-40298A
DA67-40294B
DA67-40295A
DA63-10905E
6002-000213
6002-000213
6002-000215
SPECIFICATION
SR-606, 608V
Q’TY REMARK
1SET
(1)NOBLE-BEIG
(2)MMD GRAY
(3)MILKY WHITE
(4)LIGHT GREEN
SR-646, 648EV, SR-686, 688EV
SR-606EV
SR-608EV
SR-646EV
SR-648EV
SR-686EV
SR-688EV
SR-606, 608EV
SR-606, 608EV
GPPS
GPPS SR-608, 648, 688EV
GPPS SR-608, 648, 688EV
GPPS
GPPS
STS304
POM
SR-60, 64, 68
SR-60, 64, 68
SR-60, 64, 68
M4X14 FE FZY
EXP ALL
EXP ALL
ABS MP-0160
ABS MP-0160
2S 3X8 FE, FZY
GPPS
FH1 4X12 STS304
EXP ALL
SHP1 T3.0
WITH DISPENSER
PP
GPPS
GPPS
ABS
ABS
WITH DISPENSER
TH1 4X12 FE FZY
1-4X12 FE, FZY
MAX25, FE, FZY
1-4X14 FE, FZY
1SET
1SET
1SET
1SET
1SET
1SET
1SET
1
1
2
1
1
1
1
1
1
1
1
1
2
1SET
1
2
2
2
1
3
1SET
1
1SET
1
1
1
1
1
1SET
1
1
1
2
Indicated part is for eclectrical safety components
40
Samsung Electronics
12. Packaging method
♦ Packaging specifications of door and inside of cab
♦ Completed
packaging
specification
Tape:W50X100(2EA)
Tape:W50XL150(1EA)
PriamentTape:W50XL100
P.E BAG:1EA
PAD-PACKING IN:
SR-50:W520XL750
SR-54:W660XL779
SR-58:W660XL823
FOAM-PE:T17XW50X175
Tape:W50X150
FOAM-PS:T15x500xl500
♦ Packaging specifications of rear and front
HIGH CUSHION:3EA
Tape : W50XL200(1EA)
Tape : W50xL300(2EA)
EPS:
T10XW80XL180(2EA)
Low CUSHION(R,L)
:846X145X160(2EA)
T15X60X825(2EA)
Corrugated cadrboard
box881X796X140(1EA)
54
Samsung Electronics
14. PCB Specification
14-1 Parts for service
NO
PART
1
DA26-30110B
TRANS-DC
105V/50,60HZ
YOUKYUNG
DA26-30112A
TRANS-DC
105V/50,60HZ
SEG1
DA26-30112B
TRANS-DC
127V/50,60HZ
DA26-30110C
TRANS-DC
220V/50,60HZ
DA26-30110A
TRANS-DC
240V/50HZ
2
DA32-10105B
R, R2, F-SENSOR COMMON USE
502 AT
DONGKWANG
3
3
DA32-10105G
R, F DEF-SENSOR
502 AT
DONGKWANG
2
4
DA32-10105F
EXT-SENSOR
502 AT
DONGKWANG
1
5
DA41-20149A
PCB PANEL
SR-60, 64, 68
SEOUL SEMI-CONDUCTOR
1
DISP NO
6
DA41-20105F
PCB MAIN
SR-60, 64, 68
KWANGJU ELECTRONICS
1
TOSHBA MICOM
58
SPEC.
SPEC.
VENOR
Q’TY
REMARK
1
Samsung Electronics
13 PCB Diagram circuit
Samsung Electronics
55
13-2 Part list
NO
SPEC.
CODE-NO
TMP87PH40AN
CST4.00MGWTF01
VSB-12TB
JZ1 aFS-12V
ULN2981A
UDN2003A
135*197 FR-1
MC7812CT
KIA7805PI
AL L30
FH-51H
500mA/250V
KA7533
RCN-10
SQ1201
CBE2220BA
SKHV 10910A
UZ 5.1B, 5.1V
TA0.6PI/52mm
KSR1005
LM324
75mH/10%
PH-2S 3*8
1N4004
2200uF 35V
1000uF 35V
1uF 50V
470uF 25V
33uF 25V
104Z
3.9K-F 1/4W
1.0K-F 1/4W
10K-F 1/4W
4B4002-0595
4B1283-0053
4B3068-0004
4B3068-0072
42109-101-021
42219-701-008
46029-0034
4A4008-0178
41129-602-022
41124-0043-00
4A3064-0021
4A3065-0156
4A4008-0754
4A1114-0006
4A1114-0007
4A1305-0012
4A3018-0047
4A4106-0048
40509-400-108
4A4068-0008
4A4008-0774
4A1130-0085
47008-130-081
4A4104-0109
4A1104-0087
4A1104-0641
4A1104-0500
4A1104-0057
4A1104-0025
4A1100-0340
4A1000-0409
41018-275-102
41018-275-103
1
1
2
6
1
2
1
2
1
2
1
1
1
1
3
1
1
1
19
3
1
1
2
9
1
2
1
2
1
18
2
4
6
34 R-CARBON
1K-J 1/4W
4A1000-0151
8
35 R-CARBON
36 R-CARBON
1.2K-J 1/4W
4.7K-J 1/4W
4A1000-0005
4A1000-0174
1
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
56
PART
IC-MCU(OTP)
RESONATOR
RELAY
RELAY
IC-DRIVER
IC-DRIVER
PCB-MAIN
VOLTAGE-REG
VOLTAGE-REG
HEAT-SINK “S1”
FUSE-CLIP
FUSE
IC-RESET
RC-NETWORK
RC-NETWORK
BUZZER
TACT-SW
ZERNER-DIODE
JUMP-WIRE
TRANSISTOR
OP-AMP IC
COIL
SCREW
DIODE-REC
C-ELEC
C-ELEC
C-ELEC
C-ELEC
C-ELEC
C-CERAMIC
R-METAL
R-METAL
R-METAL
Q’TY UNIT
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
VENOR
TOSHIBA
MURATA
TAKAMISWA
MATSUSHITA
ALLEGRO
ALLEGRO
PART NO.
IC01
X-TAL
RY77, RY78
RY71-RY76
IC05
IC02, IC04
CHUNGJU ELECTRONICS PCB
SAMSUNG SEMMI-CONDUCTOR RG101,RG102
SAMSUNG SEMMI-CONDUCTOR RG103
SHINDANG INDUSTRY RG101,RG102
YUNHO ELECTRONICS FUSE2
SAMJU ELECTRONICS FUSE2
SAMSUNG SEMMI-CONDUCTOR IC03
DOOSHIN ACCURACY AC701
KEUMKANG ELECTRONICS SP71-73
BUJUN ELECTRONICS PARTS BZ
KYUNGIN ELECTRONICS TEST-SW
PYUNGCHANG TRADE ZD501
WON CONSTRUCTION J01-J20
SAMSUNG SEMMI-CONDUCTOR Q801,Q802,Q803
SAMSUNG SEMMI-CONDUCTOR IC06
BUJUN INDUSTRY L801
TAIYANG METAL
FUSE
PYUNGCHANG TRADE D101-108,601
SAMHWA ELECTRIC C103
SAMHWA ELECTRIC C104,105
SAMHWA ELECTRIC C203
SAMHWA ELECTRIC C106,C107
SAMHWA ELECTRIC C801
DANGYANG HEREDITY
REMARK
NEW(PGM)
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
NEW
NEW
NEW
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
NEW
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
NEW
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
NEW
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ABCO, HANRYUK R314
NEW
ABCO, HANRYUK R315,316,317,320
NEW
ABCO, HANRYUK R301,303,305,
ACE COMMON USE
R307,309,311
ACE COMMON USE
EA ABCO, HANRYUK R201,503,601,602,R603 ACE COMMON USE
,604,605,904
ACE COMMON USE
EA ABCO, HANRYUK R502
NEW
EA ABCO, HANRYUK R401,403,405,504,R801 ACE COMMON USE
,803,905
Samsung Electronics
NO
PART
SPEC.
CODE-NO
Q’TY UNIT
37 R-CARBON
10K-J 1/4W
41018-227-103
16
38
39
40
41
42
43
44
45
46
47
48
49
50
51
12K-J 1/4W
47K-J 1/4W
4.7-J 1/4W
YW396-09AV(WHT)
YW396-09AV(RED)
YW396-05AV(WHT)
SMW250-07(WHT)
SMW250-03(WHT)
SMW250-07(YEL)
SMW250-06(WHT)
SMW250-11(WHT)
SMW250-02(WHT)
SMW250-02(BLU)
TMP87PH40AN-XXXX
41018-227-123
41018-277-473
4A1000-0261
4A6010-0530
4A6010-0546
4A6010-0470
4A6010-1407
4A6010-1387
4A6010-1409
4A6010-1402
4A6010-1427
4A6010-1382
4A6010-1385
4B4002-0825
1
8
1
1
1
1
1
1
1
1
1
1
1
1
R-CARBON
R-CARBON
R-CARBON
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
IC-MCU(MSK)
Samsung Electronics
VENOR
PART NO.
EA ABCO, HANRYUK R202,302,304,306,
R308,310,312,313,
R318,402,404,406,
R701,901,902,903
EA ABCO, HANRYUK R804
EA ABCO, HANRYUK R606-613
EA ABCO, HANRYUK R804
EA YUNHO ELECTRONICS CON10
EA YUNHO ELECTRONICS CON09
EA YUNHO ELECTRONICS CON08
EA YUNHO ELECTRONICS CON01
EA YUNHO ELECTRONICS CON06
EA YUNHO ELECTRONICS CON02
EA YUNHO ELECTRONICS CON03
EA YUNHO ELECTRONICS CON07
EA YUNHO ELECTRONICS CON05
EA YUNHO ELECTRONICS CON04
IC01
EA TOSHIBA
REMARK
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
ACE COMMON USE
NEWPGM)
57
4. Electric Diagram
1. 110~115V/60Hz, 127V/60Hz, 220V/50Hz, 240V/50Hz
CIRCUIT-DIAGTAM
“A-1”:220-240V/50,60Hz
“A-2”:110-127V/60Hz
“B-1”, “C-1”:WITHOUT EARTH
“B-2”, “C-2”:WITH EARTH
RED-RED
BLUE-BLUE
ORG-ORANGE
BRN-BROWN
PINK-PINK
GRY-GRAY
Samsung Electronics
WHT-WHITE
YEL-YELLOW
BLK-BLACK
P/BLUE-PINK/BLUE
PRP-PURPLE
W/BLK-WHITE/BLACK
S/BLU-SKY BLUE
5
5. Out Package Specification
6
Model
A
B
C
D
Remark
SR-606EV
814
899
1806
50
–
SR-608EV
814
899
1806
50
Dispenser applied
SR-646EV
899
1858
50
-
SR-648EV
814
899
1858
50
Dispenser applied
SR-686EV
814
899
1902
50
–
SR-688EV
814
899
1902
50
Dispenser applied
Samsung Electronics
15. Main components specifications
1) REGULATOR
3-TERMINAL 1A POSITIVE VOLTAGE GRGULATORS
The MC78XX/MC78XXA series of three-terminal positive regulators are available in
the TO-220 package and with several fixed output voltaes, making it useful in a
wide range of applicationes. These regulaators can provide local oncard regulation,
eliminating the distribution problems assciated with single point regulation. Each
type employs internal current limiting, thermal shut-down and safe area protection,
making it essentially indestructible. If adequate heat sinking is provided, they can
delive over aA output corrent. Although designed primarily as fixed voltage
regulators, these devices can be used with external components to obtain
adjustable voltages and currents. MC78XXI is characterized for operation from -40°
°Cto +125°c, and MC78XXC from 0°c to +125°c
TO-220 1 2 3 1 : Input 2 : GND 3 : Output
FEATURES
ORDERING INFORMATION
• UOutput Current up to 1.5A
• UOutput voltages of 5;6;8;9;10;11;12;15;18;24V
• UThermal Overload Protection
• UShort Circuit Protection
• UOutput Transistor SOA Protection
• UNo external components required
• UOutput current in excess of 1A
• UIndustrial and commercial temperature range
Device
Package
MC78XXCT
TO-220
MC78XXACT
TO-220
MC78XXT
TO-220
Operating Temperature
0~+125°C
-40~+125°C
BLOCK DIAGRAM
ABSOLUTE MAXIMUM RATINGS
Characteristic
Input Voltage (for Vo = 5V to 18V)
(for Vo = 24V)
Symbol
Rating
Unit
VIN
35
V
VIN
40
V
Thermal Resistance Junction - Cases
θ JC
5
°C/W
Thermal Resistance Junction - Air
θ♣JA
65
θ/W
Operating Temperature Range MC78XXC/AC
MC78XXI
Storage Temperature Range
Samsung Electronics
T opr
Tstg
0 ~ +125
°C
-40 ~ +125
°C
-65 ~ +150
°C
59
2) REGULATOR(MC7812C)
ELECTRICAL CHARACTERISTICS MC7812
(Refer to test circuit, T min < Ti < T max, Vi = 500mA, Vi = 19V, Ci = 0.33µF, Co = 1.0µFunless otherwise specified)
MC7805C
Characteristic
Symbol
Test Conditions
Typ
Max
11.5
12
12.5
11.4
12
12.6
V i = 14.5V to 30V
10
240
Vi = 16V to 22V
3.0
120
Io = 5.0mA to 1.5V
12
240
Io = 250mA to 750mA
4.0
120
Ti = 25°C
Output Voltage
Unit
Min
5.0mA≤Io≤1.0A, P≤15W
Vo
Vin = 14.5V to 27V
V
V i = 15.5V to 27V
Line Regulation
Load Regulation
Quiescent Current
Quiescent Current Change
∆Vo
Ti = 25°C
∆Vo
Ti = 25°C
Id
∆Id
Ti = 25°C
5.1
8
Io = 5mA to 1.0A
0.5
V i = 14.5V to 30V
1.0
mV
mV
mA
mA
Vi = 15V to 30V
∆Vo/∆T
Io = 5mA
-1
mV/°C
Vn
f = 10Hz to 100KHz Ti = 25°C
75
µ/V
Rejection
RR
V i = 15 to 25V
71
dB
Dropout Voltage
Output Voltage Drift
Output Noise Boltage
Ripple
fF = 120Hz
55
VD
Io = 1A, Ti = 25°C
2
V
Output Resistance
RO
f = 1KHz
18
mΩ
Short Circuit Current
ISC
Vi = 35V, Ti = 25°C
250
mA
Peak Current
Ipeak
Ti = 25°C
2.2
A
* Tmin < Ti < Tmax
MC78XXI : Tmin = -40°C, Tmax = 125C
MC78XXC, Tmin = 0°C, T max = 125°C
* Load and line regulation are specified at constant junction temperature. Changes in V o due to heating effects must be taken into
account separately. Pulse testint with low duty is used.
60
Samsung Electronics
MC 7805 AC(T)
ELECTRICAL CHARACTERISTICS MC7805
(Refer to test circuit, Tmin < Ti < Tmax, Io = 500mA, Vi = 10V, Ci = 0.33ßfi, unless otherwise specified)
MC7805C
Characteristic
Symbol
Test Conditions
Ti = 25°C
Output Voltage
Unit
Min
Typ
Max
4.8
5.0
5.2
4.75
5.0
5.25
5.0mA ≤ Io ≤ 1.0A, Po ≤ 15W
Vo
V i = 7V to 20V
V
V i = 8V to 20V
Line Regulation
Load Regulation
Quiescent Current
Quiescent Current Change
∆Vo
Ti = 25°C
∆Vo
Ti = 25°C
Id
∆‚Id
V i = 7V to 25V
5.0
100
V i = 8V to 12V
1.5
50
Io = 5.0mA to 1.5V
9
100
Io = 250mA to 750mA
3
50
5.0
8
T i = 25˚C
Io = 5mA to 1.0A
0.5
V i = 7V to 25V
1.3
mV
mV
mA
mA
V i = 8V to 25V
Output Voltage Drift
Output Noise Boltage
∆Vo /∆T
Io = 5mA
-0.8
mV/°C
Vn
f = 10Hz to 100KHz Ti = 25˚C
40
µ/V
Ripple
F = 120Hz
Rejection
RR
Vi = 8 to 18V
78
dB
Dropout Voltage
VD
Io = 1A, Ti = 25˚C
62
2
V
Output Resistance
RO
f = 1KHz
17
mΩ
Short Circuit Current
ISC
Vi = 35V, Ti = 25˚C
250
mA
Peak Current
Ipeak
T i = 25˚C
2.2
A
* Tmin < Ti < Tmax
MC78XXI : T min = -40˚C , Tmax = 125˚C
MC78XXC, T min = 0˚C , Tmax = 125˚C
* Load and line regulation are specified at constant junction temperature. Changes in Vo due to heating effects must be taken into
account separately. Pulse testint with low duty is used.
Samsung Electronics
61
HIGH-VOLTAGE, HIGH-CURRENT
SOURCE DRIVERS
Series UDS2980H and UDS2980R hermetically sealed source
drivers link standard low-power digital logic and relays, solenoids,
magnetic print hammers, stepping motors, LEDs, and lamps in
applications requiring separate logic and load grounds, load supply
voltages to +80V, and load currents to 500 mA.
Types UDS2981H/R and UDS2983H/R are intended for use
with 5v logic systems(TTL, Schottky TTL. DTL and 5V CMOS).
UDS2982H/R and UDS2984H/R integrated circuits are intended for
MOS interface (PMOS and CMOS) operating from supply voltages
of from 6 to 16V.
Types UDS2981H/R and UDS2982H/R will withstand an output
OFF voltage of 50 V. UDS2983H/R and UDS2984H/R drivers will
withstand a maximum output OFF voltage of 80V.
Under normal operating conditions, the devices will sustain 50
mA continuously on each of the eight outputs at an ambient
temperature of +85°c and with a supply voltage of 15V. All types
include input current-limiting resistors and output transientsuppression diodes. In all cases, outputs are swiched ON by an
active high input level.
Note that the maximum current rating may not be obtained at 55°c because of reduced beta, or at +125°c because of package
power limitations.
Dwg No A 10243
ABSOLUTE MAXIMUM RATINGS
at +25°c Free-Air Temperature
Series UDS2980H drivers are furnished in 18-pin
ceramic/metal(side-brazed) hermetic dual in-line packages. Series
UDS2980R drivers are supplied in ceramic/glass(cer-DIP) hermetic
packages. Both are processed to the requirements of MIL-STD-883.
Class B.
The same circuits are also available in 18-pin plastic dual in-line
packages (Series UDN2980A) for operation over a limited
temperature range, or where higher package power dissipation is
needes.
FEATURES
Cutput Voltage Range, VCE
(UDS298t and
UDS2982H/R).......................................5V to 50V
(UDS2983 and
UDS2984H/R).....................................35V to 80V
Input Voltage, Vin
(UDS2981 and
UDS2983H/R).................................................15V
(UDS2982 and
UDS2984H/R).................................................30V
Output Current, Iout-........................................500 mA
Ground Terminal Current,
I GND........................................................................................................ 3.0A
Power Dissipation. PD
(any one driver)............................................. 1.1W
(total package).....................................See Graph
Operating Temperature Range,
TA.............................................................................-55˚C to + 125˚C
Storage Temperature Range,
Ts............................................................................-65˚C to + 150˚C
• TTL, DTL, PMOS, or CMOS Compatible Inputs
• 500 mA Output Source Current Capability
• Transient-Protected Outputs
• High-Reliability Screening to MIL-STD-883, Class B
• Operating Temperature -55°c to+125°c
Always order by complete part number, e.g.,
See table on next page for differences between devices.
UDS2981H883
62
Samsung Electronics
ELECTRICAL CHARACTERISTICS from -55°c to +125°c (unless otherwise specified).
Applicable
Chracteristic
Symbol
Devices
Maximum Output
Leakage Current
ICEX
UDS2981/82
UDS2981/84
Maximum
Collector-Emitter
Saturain Voltage
VCE(SAT)
Fig.
Limit
VIN = 0.25 V, VS = 50 V
1
200 µA
VIN = 0.25V, VS = 80 V
1
200 µA
VIN = 2.4 V, IOUT = -100 mA
2
2.0 V
VIN = 2.4 V, IOUT = -200 mA
2
2.1 V
+25˚C
VIN = 2.4 V, IOUT = -350 mA
2
2.0 V
+125˚C
VIN = 2.4 V, IOUT = -100 mA
2
1.8 V
VIN = 2.4 V, IOUT = -200 mA
2
1.9 V
VIN = 5.0 V, IOUT = -100 mA
2
2.0 V
VIN = 5.0 V, IOUT = -200 mA
2
2.1 V
+25˚C
VIN = 5.0 V, IOUT = -350 mA
2
2.0 V
+125˚C
VIN = 5.0 V, IOUT = -100 mA
2
1.8 V
VIN = 5.0 V, IOUT = -200 mA
2
1.9 V
VIN = 2.4 V
3
295 µA
VIN = 3.85 V
3
600 µA
VIN = 12 V
3
2.3 mA
UDS2981/82
VIN = 0 V, VS = 50 V
3
10 µA
UDS2983/84
VIN = 0 V, VS = 80 V
3
10 µA
UDS2981/83
VIN = 2.4 V, VCE = 2.2 V
2
-200 mA
UDS2982/84
VIN = 5.0 V, VCE = 2.2 V
2
-200 mA
VIN = 2.4 V, VS = 50 V
4
10 mA
UDS2982
VIN = 5.0 V, VS = 50 V
4
10 mA
UDS2983
VIN = 2.4 V, VS = 80 V
4
10 mA
UDS2984
VIN = 5.0 V, VS = 80 V
4
10 mA
VS = 35 V, RL = 175 Ω
7
2.0 µs
VS = 50 V, RL = 250 Ω
7
2.0 µs
VS = 35 V, RL = 175 Ω
7
10 µs
UDS2983/84
VS = 50 V, RL = 250 Ω
7
10 µs
UDS2981/82
VIN = 0.25 V, VS = 50 V
5
50 µA
UDS2983/84
VIN = 0.25 V, VS = 80 V
5
50 µA
IF = 200 mA
6
1.75 V
UDS2981/83
UDS2982/84
Maximum
Input Current
IIN(ON)
IIN(OFF)
Maximum Output
Source Current
Maximum
Supply Current
(Outputs Open)
Maximum Turn-ON
Delay Time
IOUT
IS
tPHL
Temp.
-55˚C
-55˚C
ALL
UDS2981
UDS2981/82
+25˚C
+25˚C
UDS2983/84
Maximum Turn-OFF
Delay Time
Maximum Clamp Diode
Leakage Current
Maximum Clamp Diode
Forward Voltage
tPHL
IR
VF
UDS2981/82
ALL
+25˚C
Test Conditions
*All inputs simultaneously.
**Pused test.
*Complete part number includes a terminal letter that indicates package (H = ceramic/metal side-brazed. R = ceramic/glass cer-DIP).
Samsung Electronics
63
NPN EPITAXIAL SILICON TRANSISTOR
KSR1005
SWITCHING APPLICATION (Bias Resistor Built In)
TO-92
•Switching Circuit, Inverter, Interface circuit Driver circuit.
•Built in bias Resistor (R,=4.7KΩ, R=10KΩ)
•Complement to KSR2005
ABSOLUTE MAXIMUM RATINGS (Ta=25˚c)
Characteristic
Rating
Unit
VCBO
50
V
Collector-Emitter Voltage
V CBO
50
V
Emitter-Base Voltage
V CBO
10
V
Collector Current
IC
100
mA
Collector Dissipation
PC
300
mW
Junction Temperature
TI
150
˚C
Storage Temperature
Tstg
-55-150
˚C
Collector-Base Voltage
Symbol
1 Emitter
2 Collector
3 Base
ELECTRICAL CHARACTERISTICS (Ta=25˚C)
Characteristic
Symbol
Test Condition
Main
Typ
Max
Unit
Collector-Base Breakdown Voltage
BVCBO
IC=10µA, IB=0
50
V
Collector-Emitter Breakdown Voltage
BVCBO
IC=100µA, IB=0
50
V
Collector Cutoff Current
ICBO
VCB=40V, IB=0
DC Current Gain
HC
VCB=5V, IB=5mA
0.1
µA
30
Collector-Emitter Saturation Voltage
VCE(sat)
IC=10mA, IB=0.5mA
Output Capacitance
Cob
VCB=10V, IB=0
0.3
Current Gain-Bandwidth Product
Fr
VCB=10V, IC=5mA
Input Off Voltage
Vi(off)
VCB=5V, IC=100µA
Input On Voltage
Vi(off)
VCB=0.3V, IC=20mA
Input Resistor
R1
3.2
Resistor Ratio
R1/R2
0.42
V
3.7
pF
250
MHz
t=1MHz
0.3
V
2.5
V
4.7
6.2
KΩ
0.47
0.52
Equivalent Circuit
64
Samsung Electronics