Sharp CD-G20000P Operating instructions

MINI COMPONENT SYSTEM
MODEL
CD-G20000
SPEAKER SYSTEM
MODEL
CP-G20000S
Accessories
Please confirm that the following accessories are included.
OPERATION MANUAL
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please
read this manual carefully. It will guide you in operating your
SHARP product.
Remote control 1
(RRMCGA090AWSA)
CD-G20000
CD-G20000 Mini Component System consisting of CD-G20000
(main unit), CP-G20000 (front speaker system) and
GBOXSA133AWM3 (rear speaker system).
CP-G20000S
CP-G20000S Speaker System consisting of 2 units of CPSW20000 (active subwoofer).
AM loop antenna 1
(QANTL0010AWZZ)
Red
Grey
Black
Black
Wire for front speaker 2 Wire for rear speaker 2
(QCNWHA003AWZZ)
(QCNWHA004AWZZ)
FM antenna 1
(92LFANT1535A)
Subwoofer cable 2
(QCNWGA003AWPZ)
Note:
Only the above accessories are included.
06/2/7
CD-G20000_FR.fm
TINSZA128AWZZ
CD-G20000
CP-G20000S
SPECIAL NOTES
NOTE
This
has been tested
to
Class B digital
pursuant to Part
the
the limits for a
These
terference in a residential installation. This equipment generates, uses,
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation exposure.
2
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
accordance with the instructions, may cause harmful interference to radio
However, there is no guarantee that interference
will not occur in a
If this
does cause
harmful
to radio or
can be determined
turning
f
the
to try
.
Connect the equipment into an outlet on a circuit different from that to
Consult the dealer or an experienced radio/TV technician for help.
W
WARNING
to this equipment not expressly approved by the manufacturer could void
NOTE
It is the intent of Sharp that this product be used in full compliance with
the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
Licensed under one or more of U.S. Pat. 4,972, 484, 5,214,678,
5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,
5,740,317, 5,777,992, 5,878,080 or 5,960,037.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
IMPORTANT SAFETY INSTRUCTIONS
be read before the product is operated.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
11 Power Sources - This product should be operated only from the type
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
6 Attachments - Do not use attachments not recommended by the prod-
12 Grounding or Polarization - This product may be equipped with a
5 Cleaning - Unplug this product from the wall outlet before cleaning.
uct manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
9 A product and cart combination should be moved with
13 Power-Cord Protection - Power-supply cords should be routed so
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
that they are not likely to be walked on or pinched by items placed
upon or against them.
14 Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
Important Instruction
1 Read Instructions - All the safety and operating instructions should
CD-G20000
CP-G20000S
3
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 Outdoor Antenna Grounding - If an outside antenna or cable system
19 Object and Liquid Entry - Never push objects of any kind into this
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Important Instruction
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERV ICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18 Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
4
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
Contents
ENERGY
Y ST
TAR Program Information
Products that have earned
the ENERGY STAR
T ® are
designed to protect the
environment through
superior energy efficiency.
General Information
Page
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 10
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 - 15
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Subwoofer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the clock (Remote Control only) . . . . . . . . . . . . . . . . . 19
CD or MP3/WMA disc Playback
T comply with the ENERGY STAR
To
T ® standards mentioned above,
ENERGY STAR
T ® is a U.S. registered mark.
Special Note
Supply of this product does not convey a license nor imply any right
to distribute content created with this product in revenue-generating
broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating streaming applications (via Internet, intranets and/or other networks), other revenue-generating
content distribution systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact discs, digital versatile discs, semiconductor chips, hard drives,
memory cards and the like). An independent license for such use is
required. For details, please visit http://mp3licensing.com.
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . . . .20 - 23
Advanced CD or MP3/WMA disc playback . . . . . . . . . . . .24 - 26
MP3/WMA navigation (only for MP3/WMA files) . . . . . . . .27 - 30
Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 32
Tape Playback
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . . 33, 34
Tape Recording
General Information
®
CD-G20000
CP-G20000S
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .34 - 36
Advanced Features
Timer and sleep operation (Remote Control only) . . . . . .37 - 40
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . 41, 42
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 - 44
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46, 47
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover
5
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Precautions
General
Please ensure that the system is positioned in a well-ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
4" (10 cm)
4" (10 cm)
4" (10 cm)
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
4" (10 cm)
General Information
In case of an electrical storm, unplug the
system for safety.
Do not place active subwoofer system on
the same surface as main unit to prevent
sound interruption during playback.
Do not remove the outer cover, as this
may result in electric shock. Refer internal service to your local SHARP service facility.
ANTENNA
FM
GND AM
75 OHMS
VIDEO
OUT
REAR SPEAKERS
LEFT
: 16 OHMS MIN.
RIGHT
IMPEDANCE
RATED SPEAKER
Floor
Use the unit on a firm, level surface free from
vibration.
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generate electrical noise.
Do not place anything on top of the unit and subwoofer.
Do not expose the system to moisture, to temperatures higher
than 140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually
listening at high volumes.
6
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
Controls and indicators
CD-G20000
CP-G20000S
Front panel
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . 18, 37, 40
6. Tape (1
2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8. Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 33
9. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10. Game/Video Input Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
11. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 21
12. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 21
13. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
14. CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
15. CD Play or Repeat, Tape Play Button . . . . . . . . . . . . . 21, 25
16. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . . . . 22, 32, 34
17. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button . . . . . . . . 22, 32, 34
18. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 33
19. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
General Information
7
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Controls and indicators (continued)
Display
General Information
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. MP3/WMA Folder Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 27
3. MP3/WMA Title Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. MP3 Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9. Tape 2 Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
10. MP3/WMA Total Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 31
13. FM Stereo Receiving Indicator. . . . . . . . . . . . . . . . . . . . . . . 31
14. Tape Forward Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . 33
15. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 30, 32
16. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
17. Disc Repeat Play Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 25
18. Disc Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
19. Disc Play Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Rear panel
ANTENNA
FM
GND AM
75 OHMS
VIDEO
OUT
Reference page
1. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. Subwoofer Pre-output Jacks . . . . . . . . . . . . . . . . . . . . . . . . 14
3. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. AM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . 12
6. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. Video Output Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8. Front Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9. Rear Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
REAR SPEAKERS
RIGHT
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
8
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Front speaker
3
2
4
General Information
1
1. Woofers
2. Tweeter
3. Bass Reflex Duct
4. Speaker Terminals
Rear speaker
1. Full-range Speakers
2. Speaker Terminals
2
1
3
4
5
6
1
2
7
8
Active subwoofer
Reference page
1. Subwoofer
2. Bass Reflex Duct
3. Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. Crossover Frequency Control . . . . . . . . . . . . . . . . . . . . . . 17
6. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. Subwoofer Input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Controls and indicators (continued)
Remote control
1
9
General Information
2
3
4
10
11
12
13
21
18
22
19
23
24
20
25
14
15
5
26 27 28 29
6
7
8
17
16
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 16
2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 21
3. Tuning Up, Cursor Up Button . . . . . . . . . . . . . . . . . . . . . . . 27
4. Disc Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down, Cursor Left Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 22, 27, 32, 33, 37
5. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6. Character Input/Disc Direct Search Buttons . . . . . . . . . . . 24
7. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . 18
8. Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 18
9. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12. Tape (1
2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
13. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
14. Disc Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up, Cursor Right Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 22, 27, 32, 33, 37
15. Tuning Down, Cursor Down Button . . . . . . . . . . . . . . . . . . 27
16. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 18
17. Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 26
18. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
19. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
20. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
21. Memory Button . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 26, 32, 37
22. Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
23. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . . . 25
24. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33, 34
25. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . . . . 35
26. MP3/WMA Navigation Mode Select Button . . . . . . . . . . . . 27
27. Character Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
28. MP3/WMA Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . 23
29. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10
06/2/7
CD-G20000_E1.fm
TINSEA128AWZZ
System connections
CD-G20000
CP-G20000S
Make sure to unplug the AC power cord before making any connections.
Active Subwoofer
Rear
speaker
(right)
Front
speaker
(right)
FM
antenna
AM loop
antenna
Front
speaker
(left)
Subwoofer
connection
(see page 14)
Rear
speaker
(left)
Active Subwoofer
Subwoofer
connection
(see page 14)
ANTENNA
FM
GND AM
75 OHMS
VIDEO
OUT
REAR SPEAKERS
RIGHT
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
To AC outlet
Speaker connection
(see page 12)
Preparation for Use
Antenna connection (see page 12)
To AC outlet
To AC outlet (AC 120 V, 60 Hz)
AC power connection (see page 14)
11
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
System connections (continued)
Antenna connection
Preparation for Use
Supplied FM antenna:
Connect the FM antenna wire to the
FM 75 OHMS jack and position the FM
antenna wire in the direction where the
strongest signal can be received.
Speaker connection
AM loop
antenna
FM
antenna
Supplied AM loop antenna:
Connect the AM loop antenna to the
AM and GND terminals. Position the
AM loop antenna for optimum
reception. Place the AM loop antenna
on a shelf, etc., or attach it to a stand
or a wall with screws (not supplied).
Front speakers:
Connect the black wire to the FRONT SPEAKERS (-) terminal, and
the red wire to the FRONT SPEAKERS (+) terminal.
Rear speakers:
Connect the black wire to the REAR SPEAKERS (-) terminal, and the
grey wire to the REAR SPEAKERS (+) terminal.
Front speaker (right)
Front speaker (left)
ANTENNA
FM
GND
AM
75 OHMS
REAR SPEAKERS
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
< Assembling >
RIGHT
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
Rear speaker (right)
Red
Black
< Attaching to the wall >
Wall
Screws (not supplied)
Rear speaker (left)
Grey
Caution:
Connect the speaker wires to the speakers first, then to the unit.
Never mistake the FRONT SPEAKERS and the REAR
SPEAKERS terminals. Otherwise the unit or the speakers may be
damaged.
If you use other speakers with impedance lower
than that specified, the unit may be damaged.
Front speakers: 8 ohms Rear speakers: 16 ohms
Do not mistake the right and the left channels. The
right speaker is the one on the right side when you
face the unit.
Incorrect
Do not let the bare speaker wires touch each other.
Do not allow any objects to fall into or to be placed
in the bass reflex ducts.
Do not stand or sit on the speakers. You may be injured.
Incorrect
12
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Placing the speaker system
Outdoor FM antenna
To enjoy the surround effect, we recommend that you place each
speaker as shown to the below.
Use an outdoor FM antenna if you require better reception.
Consult your dealer.
TV
Active
subwoofer
Front
speaker
(left)
ANTENNA
FM
Front
speaker
(right)
Main unit
Surround
speaker
(left)
GND
AM
Outdoor
FM antenna
75 OHMS
75 ohms
coaxial cable
Surround
speaker
(right)
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
Notes:
The front speakers and active subwoofer are magnetically
shielded but rear speakers no magnetically shielded.
Therefore, front speakers and active subwoofer do not affect the
display even if you use them near the TV. However, some color
variation may occur, depending on the type of TV used but rear
speakers cannot put near display.
Preparation for Use
Active
subwoofer
If color variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
If the color variation is still present...
Move the speakers further away from the TV.
If any kind of magnet or an electromagnet is placed too close to
the TV and the system, irregular colors may appear on the TV
screen.
Note:
The speaker grilles are not removable.
13
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
System connections (continued)
Make sure to unplug the AC power cord of the main unit before
making any connections.
Connecting the subwoofer
AC power connection
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the unit
first, the unit will enter the demonstration mode.
Use the subwoofer cable to connect the SUBWOOFER PRE-OUT
jack on the main unit and the SUBWOOFER IN jack on the active
subwoofer.
ANTENNA
FM
GND AM
75 OHMS
Main unit
VIDEO
OUT
ANTENNA
Preparation for Use
FM
GND AM
75 OHMS
REAR SPEAKERS
RIGHT
REAR SPEAKERS
RIGHT
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
VIDEO
OUT
AC outlet
(AC 120 V, 60 Hz)
To subwoofer
output jack
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
Active subwoofer
Subwoofer cable
Active subwoofer
To subwoofer
input jack
AC outlet
(AC 120 V, 60 Hz)
14
Notes:
The unit will start the tape initialization when plugged in to the AC
outlet. During this process, an initializing sound will be heard and
the unit cannot be turned on. Wait until the process is finished.
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Cooling fan:
The main unit and the active subwoofer are built with a cooling fan at
the rear of the units for improved cooling. Please do not cover the
opening of the fan with any obstacles, as this will block proper ventilation.
Demonstration mode
When you plug the unit in for the first time, the unit will enter the
demonstration mode. You will see words scroll.
Main unit
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode),
press the X-BASS/DEMO button. The unit will enter the low power
consumption mode.
ANTENNA
FM
GND AM
VIDEO
OUT
REAR SPEAKERS
RIGHT
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
Active subwoofer
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Preparation for Use
75 OHMS
Note:
When the power is on, the X-BASS/DEMO button can be used to select the extra bass mode.
15
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Remote control
Battery installation
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
Preparation for Use
3
Open the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
Close the cover.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 11 - 15).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Remote sensor
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Battery removal:
Open the battery cover and pull up the battery to take out.
16
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
Subwoofer control
CD-G20000
CP-G20000S
Before you turn the system on/off on the main unit, minimize the
speaker volume on the main unit and turn the VOLUME control of
the subwoofer to "–".
Speaker light up
The speaker unit surface will light up and blink according to BASS
SOUND LEVEL.
During STANDBY MODE (low power consumption mode):
When subwoofer is turned ON, no light will be emitted from the
subwoofer unit.
Notes:
Observe the following to avoid malfunction and sound distortion.
Do not set the volume too high on the main unit. The subwoofer
may be damaged.
Before you switch on/off on the main unit, minimize the volume on
the main unit.
Unplug the AC power cord when connecting the subwoofer cable.
Power switch
Press the POWER ON/OFF button to turn ON the Active Subwoofer.
Preparation for Use
During STANDBY MODE (DEMO MODE):
When subwoofer is turned ON, the subwoofer unit will emit blinking
light.
Volume control
Turn the VOLUME control clockwise to increase the volume, and turn
it counterclockwise to decrease the volume.
Crossover frequency control
Adjust the high frequency cut-off point. Frequencies higher than the
set frequency are removed.
To emphasize the bass, turn this control toward 35 Hz and increase
the volume.
17
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
General control
Volume control
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase.
When it is turned counterclockwise, the
volume will decrease.
Remote control operation:
Press the VOLUME (+ or -) button to
increase or decrease the volume.
0 ..... 30 MAXIMUM
Bass control (X-BASS)
Basic Operation
When the power is first turned on, the unit
will enter the extra bass mode which
emphasizes the bass frequencies, and
"X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS/DEMO
button.
Equalizer
When the EQUALIZER MODE button is pressed, the current mode
setting will be displayed. To change to a different mode, press the
EQUALIZER MODE button repeatedly until the desired sound mode
appears.
To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Illumination light control
When the power is turned on, light illuminates around the display.
Hold down the CLEAR/DIMMER button on the remote control for 2
seconds or more to turn on/off the light.
Volume auto fade-in
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
18
In CD/TUNER/TAPE mode
In GAME/VIDEO mode
FLAT
No equalization.
FLAT
No equalization.
ROCK
For rock music.
ROCK
For rock music.
CLASSIC For classical music.
POPS
For pop music.
VOCAL Vocals are
enchanced.
JAZZ
For jazz.
CLASSIC For classical
music.
ACTION For action games.
SPORTS For sports games.
RACING For car racing
games.
Note:
The extra bass mode is canceled when the EQUALIZER MODE
button is pressed.
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
Setting the clock (Remote Control only)
5
CD-G20000
CP-G20000S
Press the
or
button to adjust the hour and then
press the MEMORY button.
or
button once to advance the time by
Press the
1 hour. Hold it down to advance continuously.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
Press the ON/STAND-BY button to turn the power on.
4
Press the
or
button to select 12-hour or 24-hour
display and then press the MEMORY button.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to
select "CLOCK", and press the MEMORY button.
"AM 12:00"
"AM 0:00"
"0:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
Press the
or
button to adjust the minutes and
then press the MEMORY button.
or
button once to advance the time by
Press the
1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to display the
time. The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" does not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 44 for details.]
2 Perform "Setting the clock" from step 1.
Basic Operation
6
19
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Listening to a CD or MP3/WMA disc
CD or MP3/WMA disc Playback
This system can play back a standard CD, CD-R/RW in the CD format
and CD-R/RW with MP3 or WMA files, but cannot record on them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3.
MP3 is a type of audio code which is processed by significant
compression from the original audio source with very little loss
in sound quality.
This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
During VBR file playback, time counter in the display may differ
from its actual playback time.
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the "CD" function is activated.
CD / button on the remote control: The unit turns on and CD
playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TAPE,TUNER,GAME/VIDEO).
Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.
WMA:
WMA files are Advanced System Format files that include audio
files which are compressed with Windows Media Audio codec.
WMA is developed by Microsoft as an audio format file for Windows Media Player.
"MP3" or "WMA" indicator will light up after the unit reads information on an MP3 or WMA disc.
20
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
1
Press the POWER ON/STAND-BY button to turn the power
on.
2
3
Press the CD button.
4
Place the disc on the disc tray 1, label side up.
Be sure to place 3" (8 cm) disc in the middle of the disc trays.
5" (12 cm)
5
Press the
but-
3" (8 cm)
button to close the disc tray 1.
MP3 indicator
WMA indicator
[CD]
[MP3/WMA]
Total number of
tracks on the disc
Total playing
time of the disc
Total number Total number
of folders
of files
Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the
/
CD or MP3/WMA disc Playback
Press the 1 button and within 5 seconds, press the
ton to open the disc tray 1.
button to start playback.
Disc play indicator
21
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Listening to a CD or MP3/WMA disc (continued)
CD or MP3/WMA disc Playback
Playback will begin from track 1 on disc 1. After that disc finishes
playing, the next disc will automatically play.
After the last track on the fifth disc is played, the unit will stop automatically.
When there is no disc in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a disc.
Various disc functions
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
To exchange other discs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the button and exchange discs.
Stop
Press in the playback
mode.
To remove the discs:
In the stop mode, press the
press the button.
Pause
Press in the playback
mode. Press the /
button to resume playback from the paused
point.
Press in the playback
or stop mode.
If you press the button
in the stop mode,
press the / button
to start the desired
track.
Press and hold down
in the playback mode.
Release the button to
resume playback.
1-
5 button and within 5 seconds,
Caution:
Do not place two discs in one disc tray.
Do not play discs of special shapes (heart, octagon, etc.) as it
may cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is restored.
If the disc tray is stopped with force, "ER-CD20" will appear on the
display for 3 seconds and the unit will not function. If this occurs,
press the ON/STAND-BY button to enter the power stand-by
mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play.
Track up/
Track down
Fast forward/Fast
reverse
22
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Notes for MP3/WMA discs:
Track up/track down is possible only within individual discs.
The sound is heard during fast forward/fast reverse with a CD, but
not with an MP3/WMA disc. For fast forward or fast reverse of an
MP3/WMA disc, refer to playback time on the display.
Fast forward/fast reverse is possible only within individual tracks.
When the end of the track is reached during fast forward, the next
track will be played. Playback of the track will begin when its beginning is reached during fast reverse.
To change the display (MP3/WMA discs only)
While a disc is playing, press the DISPLAY
button.
Each time the button is pressed, the display
will change as follows.
Track number Elapsed
playback time
Folder name
File name
CD or MP3/WMA disc Playback
Notes for CD:
Track up/track down is possible only within individual discs.
Fast forward/fast reverse is possible only within individual discs.
When the end of the last track is reached during fast forward,
"END" will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
23
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Advanced CD or MP3/WMA disc playback
To specify a disc to play
Direct track search
You can play a disc by specifying the disc number.
By using the direct search buttons, the desired tracks on the current
disc can be played.
CD or MP3/WMA disc Playback
1
Press one of the
1-
5 buttons to select the desired disc.
Use the direct search buttons on
the remote control to select the
desired track while playing the
selected disc.
Selected track number
Selected disc number
Within 5 seconds, press the / button on the main unit.
The direct search buttons allow you to select up to number 9.
When selecting number 10 or more, use the "+10" button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
Playback will begin from track 1 on the chosen disc.
After the last track on the last disc is played, the unit stops automatically.
Note:
If the disc tray with no disc is selected, playback will not start and
the disc indicator will disappear.
To stop playback:
Press the (CD ) button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
Notes:
A track number higher than the number of tracks on the disc
cannot be selected.
During random play, direct search is not possible.
24
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Repeat play
Random play
Repeat play can play all 5 discs, all tracks on a chosen disc, or a
programmed sequence continuously.
The tracks on the disc(s) can be played in random order automatically.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
To repeat all tracks on up to 5 discs:
Press the / button three times.
To repeat desired tracks:
Perform steps 1 - 6 in "Programmed play" section on page 26 and
then press the / button twice.
To cancel repeat play:
Press the / button again.
" " will disappear.
To cancel random play:
Press the / button.
"R" will disappear.
Notes:
If you press the
button during random play, you can move to
the next track by the random operation. On the other hand, the
button does not allow you to move to the previous track. The beginning of the track being played will be located.
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the
) button. Otherwise, the disc(s) will play continuously.
(CD
CD or MP3/WMA disc Playback
To repeat one disc:
Press the / button twice.
25
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Advanced CD or MP3/WMA disc playback (continued)
Programmed play
CD or MP3/WMA disc Playback
You can choose up to 32 selections for playback in the order you like.
1
While in the stop mode, press the
MEMORY button to enter the programming save mode.
2
Press one of the 1 - 5 buttons
to select the desired disc.
3
4
To clear the programmed selections:
Press the CLEAR/DIMMER button on the
remote control while the "MEMORY" indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track
programmed.
To cancel the programmed play mode:
While in the stop mode and the "MEMORY" indicator is lit, press the
CLEAR/DIMMER button on the remote control. The "MEMORY"
indicator will disappear and all the programmed contents will be
cleared.
Selected disc number
Adding tracks to the program:
If a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
Selected track number
You can also select a track by pressing the
or
button.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or
button.
Press the direct search buttons
on the remote control to select
the desired track.
Press the MEMORY button to save
the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6
Press the (CD ) button.
The total number in memory will
appear.
7
Press the
/
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
button to start playback.
26
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
MP3/WMA navigation (only for MP3/WMA files)
MP3/WMA navigation:
You can search and play files by folder or title. For example, when
you assign three titles to a file, enter genre (such as jazz) as title 1,
album name as title 2, and music title as title 3 to search the file by
any title.
You can search and play files by folder or title 1/2/3 within one
MP3/WMA disc (see page 28).
By entering a name, you can search files by folder or title 1/2/3
within one MP3/WMA disc (see page 29).
Folders or titles can be programmed within one MP3/WMA disc
(see page 30).
When you enter file names on your PC, connect words with hyphens.
This product recognizes the first word as title 1, second one as title
2, and third one as title 3. Up to three words can be recognized.
Example:
Folder
Title 1
Title 2
Title 3
(File name)
Folder
Title 1
Title 2
Title 3
AAA
(POPULAR-HITS 1-A MUSIC.mp3)
(POPULAR-HITS 2-B MUSIC.mp3)
BBB
(JAZZ-HITS 1-A MUSIC.mp3)
(JAZZ-HITS 2-B MUSIC.mp3)
CCC
(ROCK-HITS 1-A MUSIC.mp3)
(ROCK-HITS 2-B MUSIC.mp3)
(ROCK-HITS 3-C MUSIC.mp3)
(ROCK-HITS 4-D MUSIC.mp3)
Notes:
MP3 files must have the extension ".mp3".
WMA files must have the extension ".wma".
Up to 100 folders or 300 files can be read on the unit. If either limit
is exceeded, no more folders/files are displayed.
This unit recognizes and displays up to 48 characters for folder
names, and up to 32 characters for title 1/2/3.
All file/folder names appear in uppercase.
CD or MP3/WMA disc Playback
CD-G20000
CP-G20000S
27
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
MP3/WMA navigation (only for MP3/WMA files) (continued)
File search (by folder or title 1/2/3)
CD or MP3/WMA disc Playback
You can search and play files by folder or title 1/2/3 within one MP3/
WMA disc.
1
Press one of the
1 5 buttons to select a disc tray
containing an MP3/WMA disc.
2
Press the
disc.
3
Press the CD button to stop playback.
"NAVI READ" appears and the display shows the total number
of folders and files on the selected disc.
/
7
Use the
or
cursor button to scroll and select a folder
(or title), and then press the ENTER button.
Folder name
button, and the unit starts to read the MP3
If you press the / button instead of the ENTER button, all
files in the selected folder (or title) are played.
8
Use the
4
5
9
Press the NAVIGATION button.
Press the , ,
or
cursor button on the remote control to select
"FOL", "T-1", "T-2" or "T-3". To
search files by folder name, select
"FOL" (will flash).
Folder
Title 1
MP3
Title 2
Title 3
The following steps describe file search by folder:
6
Press the ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Folder name
The NAVIGATION button allows you to go one step back.
Press the DISPLAY button to
check the number of files.
cursor button to scroll and select a file.
File name
MP3 indicator
WMA indicator
Total number Total number
of folders
of files
or
Press the / button to start playback.
The unit plays from the selected file to the last file in the selected folder (or title), and the previous display returns.
File search by title 1/2/3:
In step 5, select "T-1", "T-2" or "T-3" and follow the same steps as
file search by folder.
The unit searches all files on the disc, regardless of the folder.
To stop playback:
Press the CD button.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
Notes:
In the MP3/WMA navigation mode, direct play and direct search
functions are disabled.
If a folder, title or file name does not appear, or appears
incorrectly, remove and reinsert the disc and try again.
If you press the RANDOM button in the stop mode, the MP3/WMA
navigation mode will be canceled.
28
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Character search (for folder or title 1/2/3)
By entering a name, you can search files by folder or title 1/2/3 within
one MP3/WMA disc.
1
Perform steps 1 - 3 in "File search (by folder or title 1/2/3)"
on page 28.
2
3
Press the NAVIGATION button.
5
6
If the search word is not in the folder (or title) name, "NOT
FOUND" appears and the menu returns.
Folder
Title 1
Title 2
Title 3
Press the CHARACTER button for 2 seconds.
The display will be ready for editing characters.
1st row: String table
2nd row: Input editor (8 digits)
Press the
alphabet.
Press the
display.
or
or
When finished, press the ENTER button. The unit search
es for the same name within folders (or titles).
cursor button to select the desired
button to go to the next page of character
Press the CHARACTER button and the active character will
be entered in the 2nd row of the display.
9
Use the or
(or title).
10
Press the / button to start playback.
All files in the selected folder (or title) are played, and the previous display returns.
cursor button to scroll and select a folder
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
Notes:
The unit searches regardless of the case, and names found will
appear in uppercase.
Some symbols do not appear properly.
Character entry with direct buttons:
The direct buttons on the remote
control can also be used for character entry.
In step 5 on the left, use buttons 0 9 to enter alphabets.
Alphabet types change as you
press a button.
For example, press "2" four times to enter "C".
To delete an entered character, move the cursor to the character with the or button and press the CLEAR/DIMMER button on the remote control.
7
Repeat steps 5 and 6 to enter characters.
In the folder (or title) name search, you do not have to enter the
full name. The unit searches for names beginning with the entered characters.
2
A
B
CD or MP3/WMA disc Playback
4
Press the , ,
or
cursor
button on the remote control to
select "FOL", "T-1", "T-2" or "T-3".
To search files by folder name,
select "FOL" (will flash).
8
C
Characters:
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO 7 PQRS 8 TUV 9 WXYZ
0
: indicates a space.
29
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
MP3/WMA navigation (only for MP3/WMA files) (continued)
Programmed play (for folder, title 1/2/3)
Folders or titles can be programmed within one MP3/WMA disc.
Folder, title 1, title 2 and title 3 cannot be programmed together simultaneously.
CD or MP3/WMA disc Playback
1
2
3
4
Perform steps 1 - 3 in "File search (by folder or title 1/2/3)"
on page 28.
Press the , , or cursor button on the remote control
to select "FOL", "T-1", "T-2" or "T-3" and then press the
ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Press the or cursor button to select the desired folder
(or title) and then press the MEMORY button.
Repeat step 4 for other folders (or titles).
Up to 10 folders (or 10 titles) can be programmed.
6
Flashes if the folder (or title)
is programmed
Press the NAVIGATION button.
The folder (or title) is memorized with all the files.
5
To check, add or delete programmed contents:
In the stop mode, select a folder (or title) with the or cursor button. If the folder (or title) is programmed, "MEMORY" flashes.
Press the
/
button to start playback.
Programmed play will always start from the smallest folder (or
title) number.
When you press the MEMORY button with "MEMORY" flashing,
the folder (or title) is removed from the program.
If you press the MEMORY button with "MEMORY" off, the folder
(or title) is added to the program.
To clear all programs, press the CLEAR/DIMMER button in the
stop mode.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
The programmed contents are cleared.
Notes:
The programmed contents are cleared when you eject a disc,
play another disc, switch the function, or enter the stand-by mode
with the ON/STAND-BY button.
If you press the RANDOM button in the stop mode, the MP3/
WMA navigation mode will be canceled.
If tracks are programmed using track numbers (see "Programmed play" on page 26):
In the MP3/WMA navigation mode, only program by folder (or title)
name are played. When you exit the mode, the program by folder (or
title) name are cleared.
When you exit the MP3/WMA navigation mode, program by track
number are canceled.
(Program by track number are cleared when you remove the disc.)
To stop playback:
Press the CD button.
The programmed contents are not cleared.
30
06/2/14
CD-G20000_E2.fm
TINSEA128AWZZ
Listening to the radio
CD-G20000
CP-G20000S
Tuning
3
Press the ON/STAND-BY button to turn the power on.
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
Press the TUNING (
station.
or
) button to tune in to the desired
Manual tuning:
Press the TUNING ( or ) button as many times as required
to tune in to the desired station.
Auto tuning:
When the TUNING ( or ) button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop
automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING ( or ) button
again.
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
turns on and the "TUNER" function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, GAME/VIDEO).
Radio
1
2
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
" " will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to
extinguish the "ST" indicator. The reception changes to monaural,
and the sound becomes clearer.
FM stereo mode indicator
FM stereo receiving indicator
31
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Listening to the radio (continued)
Memorizing a station
To recall a memorized station
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
Press the PRESET ( or
select the desired station.
1
2
Perform steps 1 - 3 in "Tuning" on page 31.
Press the MEMORY button to enter the preset tuning saving mode.
To scan the preset stations
The stations saved in memory can be scanned automatically.
(Preset memory scan)
1
Radio
2
3
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4
Within 30 seconds, press the MEMORY button to store that
station in memory.
) button for less than 0.5 seconds to
Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
Press the PRESET ( or ) button again when the desired
station is located.
If the "MEMORY" and preset number indicators disappear. before the station is memorized, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station.
When a new station is stored in memory, the station previously
memorized for that preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few hours
should there be a power failure or the AC power cord become
disconnected.
To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the power standby
mode.
While pressing down the button and the
button, press
the TUNER(BAND) button until "TUNER CL" appears.
32
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
Listening to a cassette tape (TAPE 1 or TAPE 2)
Tape playback
1
2
Press the ON/STAND-BY button to turn the power on.
3
Load a cassette into the
TAPE 1 compartment or
TAPE 2 compartment
with the side to be played
facing toward you.
4
Press the TAPE (1
want to listen to.
5
Press the / (TAPE
to start playback.
Open the cassette compartment by pushing the
area marked " ".
TAPE 1
TAPE 2
2) button to select the cassette you
)
Tape Playback
Before playback:
For playback, use normal or low-noise tapes for the
best sound. (Metal or CrO tapes are not
recommended.)
Do not use C-120 tapes or poor-quality tapes, as
they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
CD-G20000
CP-G20000S
Tape play indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TAPE (1 2) button (main unit and remote control): The unit
turns on and the "TAPE" function is activated.
TAPE
button on the remote control: The unit turns on and the
"TAPE" function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, GAME/VIDEO).
Auto power off function:
In the stop mode of tape operation, the main unit enters the standby mode after 15 minutes of inactivity.
33
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Listening to a cassette tape (TAPE 1 or
TAPE 2) (continued)
Various tape functions
Tape Playback
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
Stop
Press in the playback,
fast forward or rewind
mode.
Fast
forward/
Fast rewind
(TAPE 2
only)
Press in the playback
or stop mode.
Recording on a cassette tape
Before recording:
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
The volume and sound controls can be adjusted with no effect
on the recorded signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or
CrO tapes.
Recording can be operated in the TAPE 2 compartment only.
The TAPE 1 is for playback only.
Erase-prevention tab of cassette tapes:
When recording on a cassette tape, make sure that the eraseprevention tabs are not removed. Cassettes have removable
tabs that prevent accidental recording or erasing.
To protect the recorded sound, remove the tab after recording.
Cover the tab hole with adhesive tape to record on the tape
without the tab.
Caution:
To remove the cassette, press the button, and then open the
compartment.
Before changing from one tape operation to another, press the
button.
If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not open.
In this case, wait until the power is restored.
Side A
Tab for side B
Tab for side A
34
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Recording from a CD (or MP3 disc)
1
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the CD button.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
button.
5
6
Press one of the
disc.
1-
5 buttons to select the desired
Within 5 seconds, press the
/
button to start recording.
Recording is started from the selected CD. When the
playback of the last track is finished or the end of the tape is
reached, the CD and the cassette will stop automatically.
Playback of the disc will start approximately 7 seconds after
the tape starts.
Tape Recording
Recording will be paused.
To stop recording:
Press the button.
The CD and tape will stop.
35
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Recording on a cassette tape (continued)
To perform programmed recording:
1 Program discs and tracks. (See page 26.)
2 Press the
button.
3 Press the / button.
To stop recording:
Press the button.
The disc and tape will stop.
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
1
2
Recording from the radio
Tape Recording
1
2
3
Load a prerecorded cassette
into the TAPE 1 cassette compartment. Insert a blank tape
into the TAPE 2 cassette compartment.
Tune in to the desired station. (See page 31.)
TAPE 1
3
Press the TAPE (1
the display.
Press the
4
Press the
button.
Recording will be paused.
5
Press the
button.
Press the
/
button to start recording.
To interrupt recording:
Press the
button.
To resume recording, press the
/
button.
To stop recording:
Press the button.
Note:
If you hear a whistling noise while recording an AM station, move the
AM loop antenna.
TAPE 2
It is recommended that the recording tape is the same length as
the master tape.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Recording will be paused.
4
Press the ON/STAND-BY button to turn the power on.
/
2) button until "TAPE 1" appears on
button to start dubbing.
To stop dubbing:
Press the button.
TAPE 1 and TAPE 2 will simultaneously stop.
Erasing recorded tapes
1
Load the tape to be erased into the TAPE 2 cassette
compartment with the side to be erased facing toward you.
2 Press the TAPE (1 2) button until "TAPE 2" appears on the
display.
3 Press the
button.
4 Press the / button to start erasing.
Note:
Make sure that the TAPE 1 is not in use.
36
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
Timer and sleep operation (Remote Control only)
CD-G20000
CP-G20000S
Timer playback:
The unit turns on and plays the desired source (CD, MP3 disc, tuner,
tape) at the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.
This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.
Once timer play and once timer recording works for
one time only at a preset time.
For example, if you are away but want to record a program on a
radio station.
Timer playback or timer recording
Before setting timer:
Daily timer:
Daily timer play and daily timer recording works at
the same preset time everyday.
For example, set the timer as a wake up call every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to record a radio program, and use
the daily timer to wake up.
1 Set the daily timer (pages 37 - 39).
2 Set the once timer (pages 37 - 39).
1 minute or more
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
Once timer
Daily timer
Start
1 Check that the clock is set to the correct time (refer to page 19).
If it is not set, you cannot use the timer function.
2 For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the TAPE
2 cassette compartment.
Advanced Features
Once timer:
Stop
Start
Stop
Note:
When the setting times for the daily timer and once timer overlap,
the once timer takes priority. Allow an interval of at least 1 minute
between operations.
Set the clock to the correct time if "ONCE" or "DAILY" does not
appear.
Continued to the next page
37
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Timer and sleep operation (Remote Control only) (continued)
4
Within 10 seconds, press the
or
button to
select "ONCE SET" or "DAILY SET", and press the
MEMORY button.
5
Press the
or
button to select "PLAY" or
"REC", and press the MEMORY button.
Advanced Features
White
9
Switch input with the
or
button, and then
press the MEMORY button.
To select the timer playback source: CD, TUNER, TAPE 1 or
TAPE 2.
To select the timer recording source: TUNER.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY
button.
If a station has not been programmed, "NO PRESET" will
be displayed and timer setting will be canceled.
10
Adjust the volume using the VOLUME control, and then
press the MEMORY button.
Do not turn the volume up too high.
11
Press the ON/STAND-BY button to enter the power standby mode.
The "TIMER" indicator lights up and the unit is ready for timer
playback or timer recording.
Red
The illustrations show the daily timer setting.
6
Press the
or
button to adjust the hour and
then press the MEMORY button.
The illustrations show the timer playback setting in the daily
timer mode.
7
Press the
or
button to adjust the minutes and
then press the MEMORY button.
8
Set the time to finish as in steps 6 and 7 above.
38
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
When the preset time is reached, playback or recording
will start.
The volume will increase gradually until it reaches the preset
volume.
13
When the timer end time is reached, the system will enter
the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer will operate at the same time every day. It will
continue until the daily timer setting is canceled. Cancel the
daily timer when it is not used.
Note:
When performing timer playback or recording using another unit
connected to the GAME INPUT jacks, select "GAME" in step 9.
This unit will turn on or enter the power stand-by mode automatically,
however, the connected unit will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE CALL" or "DAILY CALL", and press the MEMORY button.
The unit returns to the timer stand-by mode after displaying the
settings in order.
Canceling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE OFF" or "DAILY OFF", and press the MEMORY button.
Timer will be canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE ON" or "DAILY ON", and press the MEMORY button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
Advanced Features
12
39
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Timer and sleep operation (Remote Control only) (continued)
Sleep operation
The radio, CD, MP3 disc and cassette tape can all be turned off
automatically.
Advanced Features
1
2
3
4
Play back the desired sound source.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
"SLEEP", and press the
MEMORY button.
Press the
or
button to select the time.
(Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
5 minutes - 1 minute 1-minute intervals
5
Press the MEMORY button.
"SLEEP" will appear.
6
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 1 minute before the sleep
operation finishes.
To confirm the remaining sleep time:
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP X : XX".
"X : XX" is sleep remaining time.
The remaining sleep time is displayed for about 10 seconds.
You can change the remaining sleep time while it is displayed by
pressing the MEMORY button (steps 4 - 5).
To cancel the sleep operation:
Press the ON/STAND-BY button while "SLEEP" is indicated.
To cancel the sleep operation without setting the system to the
stand-by mode, proceed as follows.
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP OFF", and press the MEMORY button.
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
Sleep and timer recording:
For example, you can fall asleep listening to the CD and record radio
programs while sleeping.
1
2
Set the sleep time (see left, steps 1 - 5).
While the sleep timer is set, set the timer playback or recording
(steps 2 - 10, pages 37 - 38).
Sleep timer setting
Timer playback or
recording setting
1 minute - 3 hours
Sleep operation will
automatically stop.
End time
Desired time
Timer playback or recording
start time
Caution:
When using the cassette deck, be sure the tape length is long
enough to perform both functions. If you want to sleep and wake up
listening to a tape, and the length of the tape is shorter than the sleep
timer setting, timer playback or recording will not be possible.
40
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
Enhancing your system
CD-G20000
CP-G20000S
The connection cord is not included. Purchase a commercially
available cord as shown below.
Game system, VCR,
DVD player, etc.
Listening to sounds of Game, VCR, DVD, etc.
1
Connect a video game system, VCR, DVD, etc. to the front
GAME INPUT (VIDEO, AUDIO L and R) jacks.
2
Connect a TV to the rear VIDEO OUT jack.
Switch the TV input to auxiliary.
Yellow
White
Press the GAME/VIDEO button.
Play the connected equipment.
You can enjoy sounds from the supplied speakers and images
on the TV.
Yellow White Red
Red
Press the ON/STAND-BY button to turn the power on.
Note:
To prevent noise interference, place the unit away from the television.
Video cable
(not supplied)
Auto power on function:
When you press any of the following buttons, the unit turns on.
GAME/VIDEO button (main unit and remote control): The unit
turns on and the "GAME" function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, GAME/VIDEO).
RCA cord
(not supplied)
TV
To video
input jack
Advanced Features
3
4
5
To the line output jacks
To record sounds of Game, VCR etc.
ANTENNA
FM
GND AM
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the GAME/VIDEO button.
3
Press the
4
Press the
5
Play the game system, VCR, etc.
75 OHMS
Yellow
Video cable
(not supplied)
VIDEO
OUT
Yellow
REAR SPEAKERS
RIGHT
button.
/
button.
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
41
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Enhancing your system (continued)
Troubleshooting chart
Headphones
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
Advanced Features
Before plugging in or unplugging the headphones, reduce the
volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
General
Symptom
Possible cause
The clock is not set to the Did a power failure occur? Reset
correct time.
the clock. (Refer to page 19.)
When a button is pressed, Set the unit to the power standthe unit does not respond.
by mode and then turn it back on.
If the unit still malfunctions, reset
it. (Refer to page 44.)
No sound is heard.
Is the volume level set to "0"?
Are the headphones connected?
Are the speaker wires
disconnected?
CD player
Symptom
Possible cause
Playback does not start.
Is the disc loaded upside down?
Playback stops in the
Does the disc satisfy the
middle or is not performed
standards?
properly.
Is the disc distorted or
scratched?
Playback sounds are
Is the unit located near excessive
skipped, or stopped in the
vibrations?
middle of a track.
Is the disc very dirty?
Has condensation formed inside
the unit?
42
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Tuner
Symptom
Cannot record.
Possible cause
Is the erase-prevention tab
removed?
Cannot record tracks with Is it a normal tape? (You cannot
proper sound quality.
record on a metal or CrO tape.)
Cannot erase completely.
Sound skipping.
Is there slack in the tape?
Is the tape stretched?
Cannot hear treble.
Are the capstans, pinch rollers,
or heads dirty?
Sound fluctuation.
Cannot remove the tape. If a power failure occurs during
playback, the heads remain
engaged with the tape. Do not
open the compartment with great
force.
Symptom
The radio makes unusual
noises continuously.
Possible cause
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop
antenna placed properly? Move
the antenna away from the AC
power cord if it's located nearby.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
Remote control
Symptom
The remote control does
not operate.
References
Cassette deck
Possible cause
Is the AC power cord of the unit
plugged in?
Is the battery polarity correct?
Are the batteries dead?
Is the distance or angle
incorrect?
Does the remote control sensor
receive strong light?
43
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Troubleshooting chart (continued)
If trouble occurs
Before transporting the unit
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the unit
with discs left inside can damage the unit.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
References
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
Clearing all the memory (reset)
1
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the
button and the button, press the
TUNER (BAND) button until "CLEAR ALL" appears.
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD
collection and player.
Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
NO
TUNER
(BAND)
YES
Correct
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
44
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
Maintenance
CD-G20000
CP-G20000S
Dirty heads, capstans or pinch rollers can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
When cleaning the heads, pinch rollers, etc., unplug the unit which
contains high voltages.
A
TAPE 1
D
E
B
B
C
C
TAPE 2
Playback head
Capstan
Pinch roller
Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be
performed periodically. Lens cleaners are commercially available.
Contact your local CD software dealer for options.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause malfunctions.
References
Cleaning the tape-handling parts
Erase head
Recording/Playback head
After long use, the deck's heads and capstans may become
magnetized, causing poor sound. Demagnetize these parts once
every 30 hours of playing/recording time by using a commercial
tape head demagnetizer. Read the demagnetizer's instructions
carefully before use.
45
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
General
Power source
Power consumption
Dimensions
References
Weight
AC 120 V, 60 Hz
175 W
Width: 10-1/4" (260 mm)
Height: 13" (330 mm)
Depth: 12-7/8" (322 mm)
9.8 lbs. (21.56 kg)
CD player
Type
Signal readout
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
D/A converter
1-bit D/A converter
Frequency response 20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
Amplifier
Output power
Front speakers 150 watts minimum RMS per channel into
8 ohms from 100 Hz to 20 kHz, 10% total
harmonic distortion
Rear speakers 75 watts minimum RMS per channel into
16 ohms from 5 kHz to 20 kHz, 10% total
harmonic distortion
Output terminals
Front speakers: 8 ohms
Rear speakers: 16 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Subwoofer pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Video output: 1Vp-p (75 ohms)
Input terminals
Game/Auxiliary (audio signal):
500 mV/47 k ohms
Game/Video: 1Vp-p (75 ohms)
46
06/2/14
CD-G20000_E3.fm
TINSEA128AWZZ
CD-G20000
CP-G20000S
Tuner
FM: 87.5 - 108.0 MHz
AM: 530 - 1,720 kHz
Cassette deck
Frequency response 50 - 14,000 Hz (normal tape)
Signal/noise ratio
55 dB (TAPE-1 playback)
50 dB (TAPE-2 recording/playback)
Wow and flutter
0.3 % (WRMS)
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
Front speaker
Type
Type
2-way type speaker system
2" (5 cm) tweeter x 1
5-1/8" (13 cm) woofer x 2
270 W
135 W
8 ohms
Width: 7-11/16" (195 mm)
Height: 15-3/4" (400 mm)
Depth: 9-5/8" (244 mm)
10.8 lbs. (4.9 kg)/each
Full-range speaker system
4" (10 cm) speaker x 2
130 W
65 W
16 ohms
Width: 5-11/16" (145 mm)
Height: 15-3/4" (400 mm)
Depth: 9-1/8" (231 mm)
6.4 lbs. (2.9 kg)/each
Active subwoofer
Power source
Power
consumption
Output power
Input terminals
Speaker type
Impedance
Dimensions
Weight
AC 120 V, 60 Hz
105 W
300 watts minimum RMS into 6 ohms from
50 Hz to 120 Hz, 10% total harmonic
distortion
Subwoofer input (audio signal):
200mV / 10 k ohms at 70 Hz
10" (25 cm) woofer
6 ohms
Width: 18-1/8" (460 mm)
Height: 15-3/4" (400 mm)
Depth: 15-13/16" (402 mm)
44.4 lbs. (20.2 kg)/each
References
Frequency range
Rear speaker
47
06/2/15
CD-G20000_E3.fm
TINSEA128AWZZ
z
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
SHARP ELECTRONICS CORPORATION
CD-G20000
System
Sharp Plaza,
Mahwah,Mini
NewComponent
Jersey 07430-2135
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
SHARP CORPORATION
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
06/2/7
CD-G20000_B.fm
Printed in Malaysia
TINSEA136AWZZ
06B R MW 1
TINSEA128AWZZ