Cooper Lighting MS185W Instruction manual

Add to my manuals
5 Pages

advertisement

Cooper Lighting MS185W Instruction manual | Manualzz

Instruction Manual/Instrucciones

Questions?/¿Preguntas? 1-800-334-6871 [email protected]

PACKAGING CONTENTS/CONTENIDO DEL PAQUETE

A. Motion detector

and light fixture

Detector de

movimiento y

artefacto de luz

B. Coverplate gasket

Junta de la placa

de cubierta

C. (2) Lampholder gaskets

(2) Juntas obturadoras

del receptáculo

D. (2) #6 and (2) #8 mounting screws

(use the size that fits your junction box)

(2) Tornillos #6 y (2) tornillos #8 de montaje

(utilice el tamaño que mejor se adecue a

su caja de conexión)

E. (3) Wire nuts

(3) Tuercas

para alambre

F. Color-matched

center hole plug

Tapón para agujero

central de color

coincidente

G. Center bolt

Perno central

H. Mounting bracket

Soporte de montaje

MS185 (Bronze)

MS185W (White)

ENGLISH

ITEMS REQUIRED

(Purchase separately)

• Phillips screwdriver

• Outdoor weatherproof silicone caulking

• (2) 100 watt (MAX) PAR 38 floodlight bulbs

NOTE: This fixture was designed to work with up to 150 watt maximum PAR halogen flood bulbs. For improved energy efficiency, lower wattage PAR halogen flood bulbs may be used.

Compact Fluorescent (CFL) bulbs contain electronics which may interfere with the motion sensing function of your fixture and are not recommended. To meet ENERGY STAR ® requirements, maximum lamp wattage can not exceed 250 watts.

HOW IT WORKS

Your motion activated floodlight senses heat images from objects such as people, large animals and automobile engines.

When motion is detected, the lights will automatically turn on. Once motion has stopped, the lights will turn off after a preselected time delay. Your motion activated floodlight may also be used as a standard floodlight.

Up to

70 feet

WARNINGS AND CAUTIONS

• Read these instructions.

180 degrees

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• For outdoor use only.

• cULus LISTED for wet locations.

• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.

• Fixture should be mounted to a grounded recessed mounted standard junction box marked

for use in wet locations.

• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.

• Do not allow sensor head to touch light housing – maintain at least 1 in. space between

fixture and sensor.

• Fixture should be installed by persons with experience in household wiring or by a qualified

electrician. The electrical system, and the method of electrically connecting the fixture to it,

must be in accordance with the National Electrical Code and local building codes.

• Always replace bulb with the same wattage or lower wattage than included. Installing a

bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb will void

the warranty (maximum 150 watt halogen bulb). To meet ENERGY STAR ® requirements,

maximum lamp wattage can not exceed 250 watts.

• For proper operation and protection against damage, the motion

sensor head adjustment knobs must be facing the ground.

• Keep away from flammable objects. Do not position fixture within 2 in.

of any combustible materials.

• Disassembly of your fixture will void the warranty.

• Your fixture is prewired and preassembled for easy installation.

• MINIMUM 90° C SUPPLY CONDUCTORS.

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Under Part 15 of the FCC Rules, any changes or modifications to the motion detector

described in this instruction sheet that are not expressly approved by Cooper Lighting, LLC

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authorization to operate this equipment.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

• Install the motion sensor/transmitter 8-12 feet

above the ground. (Motion sensor is less sensitive

above 12 feet.)

• Locate motion sensor so motion moves across

detection zone (Fig. 1).

• Locate sensor away from heat producing sources to

prevent false triggering. Also be very careful not to

include objects such as windows, white walls and

water in the detection zone.

• Locate sensor away from moving objects such as

trees, large shrubs and street traffic.

• Do not install more than one motion activated

floodlight on one wall switch.

Fig. 1

1

MOUNTING AND WIRING YOUR FIXTURE

WARNING: Risk of electric shock. Disconnect power at fuse or circuit breaker before installing or servicing.

NOTE: Fixture can be wall or eave mounted.

NOTE: Coverplate mounts to recessed mounted standard junction boxes (Fig. 2). Junction box must be at least 1-1/2 in. in depth for proper installation for recessed mount application.

1. Line up the holes on the mounting bracket (H) with the holes on your junction box. Using either (2) #6 screws or (2) #8 screws (D) (depending on size of the holes in your junction box), attach the mounting bracket (H) to your junction box (Fig. 3).

2. Thread fixture wires through coverplate gasket (B)

(Fig. 4).

3. Connect fixture black wire to house black wire, fixture white wire to house white wire, and copper colored ground wire (coming from the fixture coverplate) to house ground wire using wire nuts

(E) provided.

4. Attach fixture (A) to the mounting bracket (H) using the center bolt (G) provided. Be sure no loose wires remain sticking out from underneath the coverplate.

Insert plastic color-matched plug (F) in center bolt hole for finished appearance (Fig. 5).

5. Apply silicone caulk around the edges of the coverplate to provide a watertight seal from rain and moisture.

6. Insert lampholder gaskets (C) into lampholder assembly, tightly against lampholder, and screw bulbs into each lampholder (Fig. 6). (Do not overtighten bulbs.)

7. Turn on power at main fuse/breaker box.

OPERATING YOUR FIXTURE

1. Move slide switch on bottom of the sensor to “TEST”. Set sensitivity knob to medium

(halfway) (Fig. 7).

2. Turn on the power to fixture. Allow fixture to warm up approximately 40 seconds before testing. (Lights may not come on during warm-up period.)

3. Aim sensor head toward desired detection area, maintaining a 15° down angle to allow moisture to drain.

NOTE: Maintain air spacing between lamps and sensor head, at least 1 in. Make sure sensor head is positioned with control switches facing towards the ground.

4. Walk across the detection zone at the farthest distance you wish your detector to detect motion.

5. Adjust sensitivity until you get desired results. Light will turn off 4 seconds after all motion stops.

NOTE: For maximum range performance, allow fixture to operate in any mode (with power to the unit) for at least 48 hours.

6. Move slide switch to 4 min. or 12 min. (AUTO mode). At dusk lights will operate in the AUTO setting.

C

1-1/2 in.

Fig. 2

1-1/2 in.

Round

H

Fig. 3

Octagonal

D

D

E

E

B

Fig. 4

E

A

Wall mount

A

A

Eave mount

Fig. 5

Fig. 6

Fig. 7

G

C

F

-

SENSITIVITY

+

TEST 4 MIN. 12 MIN.

ENERGY STAR

®

ENERGY STAR ® is sponsored by the U.S.

Environmental Protection Agency & U.S.

Department of Energy.

Visit www.energystar.gov to learn more.

To meet ENERGY STAR exceed 250 watts.

® requirements, the photosensor control knob must be in the

“Auto” mode to prevent operation during full daylight. Maximum lamp wattage can not

SELECTING YOUR DESIRED FEATURE

Mode of

Operation

“Auto” Setting

(motion activated)

Lights should turn ON with motion only at night and should turn OFF after

4-12 minutes of no motion.

MODE Knob

Adjustment

AUTO 4 MIN or

AUTO 12 MIN

AUTO 4 MIN or

AUTO 12 MIN

Dusk-to-Dawn Setting

(activated only at night)

Lights should stay ON from dusk to dawn and then reset to “Auto” setting at the next dawn.

Standard Floodlight Setting

Lights should stay ON continuously both day and night

(must be reset manually).

TEST

Test Setting

Lights should turn ON with motion both day and night.

Lights should turn OFF after 4 seconds.

Return to “Auto”

(motion activated) Setting from any of the above settings.

TEST

AUTO 4 MIN or

AUTO 12 MIN

How to Set

Power Switch

Keep the power to the fixture ON.

Turn the power

OFF-ON-OFF-ON within 3 seconds.

Turn the power

OFF-ON-OFF-ON within 3 seconds.

Keep the power to the fixture ON.

Turn the power OFF for at least 40 seconds and then back ON.

TROUBLESHOOTING

Problem

Outdoor Light

Does Not Come

On With Motion

At Night

Cause / Solution

No power to the fixture.

• Check if circuit breaker tripped.

• Confirm wall switch is ON.

Bulb is faulty.

• Replace bulb.

Surrounding external ambient light is too bright. (If so, the unit may think it is daytime.)

• Re-aim the head.

• Relocate or reposition the unit away from the light.

TURN OFF POWER BEFORE CONTINUING

Wiring to the unit is loose.

• Check wiring, and reconnect if necessary using wire

nuts (E) provided.

Outdoor Light

Comes On For No

Apparent Reason

At Night

There is motion in the detection zone.

• Make sure the sensor is not picking up moving objects such as

trees, traffic, etc.

TEST FOR YOURSELF.

• Cover the sensor lens with cardboard to prevent sensor from

detecting motion. If the light stays off, something in the detection

zone is triggering the sensor.

• If this is the case, reduce the sensitivity.

• Reposition the sensor.

* If the light stays on with the sensor lens covered, contact

customer service.

Light Stays On At

Night And Does

Not Turn Off

Light

Continuously

Blink On and

Off At Night

There is motion in the detection zone.

• Make sure the sensor is not picking up moving objects such as

trees, traffic, etc.

• Reduce the sensitivity.

• Reposition the sensor.

Unit is in override mode (if there is no motion).

• Turn the light switch to the OFF position for 40 seconds, and then

turn back to the ON position. This will send the unit back into the

“Auto” mode.

* If the light stays on with the sensor lens covered, contact

customer service.

The light given from the unit’s own lamp is affecting the motion sensor.

• Re-aim the lamp.

• Reposition motion sensor.

2

Problem

Light Is On

During The Day

Cannot Activate

Dusk to Dawn

Mode At Night

(Override)

Cause / Solution

The controls on the bottom of the motion sensor are in the test mode.

• Move the switch to the AUTO 4 or 12 position.

The motion detector is shadowed.

• Reposition motion sensor.

Surrounding external ambient light is too bright. (If so, the unit may think it is daytime.)

• Re-aim the head.

• Relocate or reposition the unit away from the light.

Not enough time is allowed to enter the dusk to dawn mode.

• Turn power OFF-ON-OFF-ON within 3 seconds.

There is more than one fixture on an indoor wall switch.

• If so, put them on separate switches.

2-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

Cooper Lighting, LLC (“Cooper Lighting”) warrants to customers that, for a period of two years from the date of purchase, Cooper Lighting’s products will be free from defects in materials and workmanship. The obligation of Cooper Lighting under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to Cooper Lighting. This is required before warranty performance shall be rendered.

This warranty does not apply to Cooper Lighting products that have been altered or repaired or that have been subjected to neglect, abuse, misuse or accident (including shipping damages).

This warranty does not apply to products not manufactured by Cooper Lighting which have been supplied, installed, and/or used in conjunction with Cooper Lighting products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:

IN NO EVENT SHALL COOPER LIGHTING BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,

STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL

THE LIABILITY OF COOPER LIGHTING FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR

CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE,

REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY OF ANY REPLACEMENT

PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING PRODUCTS GIVING RISE

TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

To obtain warranty service, please contact Cooper Lighting, LLC, at 1-800-334-6871, press option 2 for Customer Service, or via e-mail [email protected] and include the following information:

• Name, address and telephone number

• Date and place of purchase

• Catalog and quantity purchase

• Detailed description of problem

All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return

Goods Authorization Number from the Company will be refused.

Cooper Lighting, LLC is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.

Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.

For assistance, call 1-800-334-6871 or e-mail us at [email protected]

Printed in China

ESPAÑOL

ARTÍCULOS NECESARIOS

(se compran por separado)

• Destornillador en cruz (Phillips)

• Calafateo de silicona resistente a la intemperie

• (2) lámparas para proyector tipo PAR 38 de 100 W (máximo)

NOTA: Este accesorio fue diseñado para trabajar con bombillas reflectoras de Halógeno PAR de

150 vatios como máximo. Para mayor eficiencia de energía, use bombillas reflectoras

Halógeno PAR de menor vataje. No se recomienda el uso de bombillas fluorescentes compactas (CFL) porque tienen partes electrónicas que pueden interferir con las funciones de detección de movimiento de su accesorio. Para cumplir con los requerimientos de ENERGY

STAR ® , la potencia máxima de la bombilla no debe exceder 250 W.

CÓMO FUNCIONA

La lámpara de alta intensidad activada por movimiento detecta imágenes térmicas de objetos tales como personas, animales grandes y motores de automóviles.

Cuando se detecte movimiento, la luz se encenderá automáticamente. Una vez que el movimiento haya cesado, la luz se apagará después de un tiempo de retardo preseleccionado. Esta lámpara de alta intensidad activada por movimiento también puede ser utilizada como una lámpara de alta intensidad estándar.

Hasta

70 pies

ADVERTENCIAS Y PRECAUCIONES

• Lea estas instrucciones.

• Guarde estas instrucciones.

• Atienda todas las advertencias.

• Siga todas las instrucciones.

180 grados

• Sólo para uso en exteriores.

• cULus para ubicaciones mojadas.

• El portalámparas debe estar conectado a una fuente de energía de 120 Voltios, 60 Hz.

Cualquier otro tipo de conexión anula la garantía.

• Debe montar el artefacto sobre una caja de conexiones empotradas con toma de

tierra marcada para usar en lugares húmedos.

• Adecuado para instalarse en la pared o en aleros solamente. No es adecuado para

instalarse montándolo en el suelo.

• No permita que el sensor toque el alojamiento de la lámpara – mantenga por lo menos

1 pulgada (2,54 cm) de espacio entre el portalámparas y el sensor.

• El portalámparas debe ser instalado por personas con experiencia en cableado

doméstico o por un electricista calificado. El sistema eléctricoy el método de conexión

eléctrica del portalámparas debe cumplir con el Código eléctrico nacional y los códigos

locales sobre edificios.

• Reemplace siempre la bombilla con una del mismo vatiaje o más bajo que el marcado. Si

instala lámparas de mayor potencia, puede crear riesgo de incendio. Si usa lámparas de

mayor potencia, se anula la garantía. (Utilice una bombilla de halógeno de un máximo de

150 W.) Para cumplir con los requerimientos de ENERGY STAR ® , la potencia máxima de la

bombilla no debe exceder 250 W.

• Para un funcionamiento y protección adecuados contra posibles daños,los botones de

ajuste de la cabeza del sensor de movimiento se deben ajustar en dirección al piso.

• Manténgalo alejado de objetos inflamables. No coloque el artefacto en

posición dentro de 2 pulgadas (5 cm) de cualquier material combustible.

• Si desarma el artefacto, se anula la garantía.

• La lámpara es percableada y ensamblado para facilitar la instalación.

• UTILICE CONDUCTORES DE SUMINISTRO QUE SOPORTEN UN MÍNIMO DE 90°C.

• Este dispositivo cumple con la Parte 15 de las Reglas de la Comisión Federal de

Comunicaciones (FCC) de los E. U. de A. La operación está sujeta a las dos condiciones

siguientes: (1) Este dispositivo no puede causar interferencia dañina, y (2) este dispositivo

debe aceptar toda interferencia recibida, incluyendo la interferencia que pueda causar un

funcionamiento indeseado. Según la Parte 15 de las Reglas de la FCC, todo cambio o

modificación al detector de movimiento descripto en esta hoja de instrucciones que no

esté expresamente aprobado por Cooper Lighting, LLC podría anular la autorización del

usuario para operar el equipo.

NOTA: Este equipo ha sido probado, y se ha verificado que cumple con los límites de un dispositivo digital Clase B, de acuerdo con la Parte 15 de las Reglas de la FCC. Estos límites están diseñados a fin de proveer una protección razonable contra la interferencia dañina en una instalación residencial. Este equipo genera, usa y puede irradiar energía de radio frecuencia, y si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia dañina en las comunicaciones de radio. Sin embargo, no se garantiza que no vaya a producirse interferencia en una instalación en particular. Si este equipo efectivamente causa una interferencia dañina en la recepción de radio o televisión, lo que puede determinarse apagándolo y encendiéndolo, se recomienda al usuario que trate de corregir la interferencia por medio de una o más de las siguientes medidas:

- Reoriente o cambie de lugar la antena receptora.

- Aumente la separación entre el equipo y el receptor.

- Conecte el equipo en un tomacorriente que esté en un circuito difer ente de aquél al que

se conecta el receptor.

- Consulte a su proveedor, o a un técnico de radio / TV experimenta do, para que le ayuden.

ADVERTENCIA: Las Reglamentaciones de la FCC establecen que todo cambio o modificación no autorizados en este equipo, que no estén aprobados expresamente por el fabricante, podrían anular la autorización del usuario para operar el equipo.

GUARDE ESTAS INSTRUCCIONES.

PARA OBTENER LOS MEJORES RESULTADOS

• Instale el sensor de movimiento / transmisor a

8 – 12 pies (2,45 –3,65 m) de altura sobre el suelo

(por encima de 12 pies / 3,65 m, el sensor de

movimiento es menos sensible).

• Coloque el portalámparas de manera que se mueva

por toda la zona de detección (Fig. 1).

• Coloque el sensor lejos de fuentes que produzcan

calor, a fin de evitar falsos disparos. Además, medida

de lo posible, tenga mucho cuidado de no incluir

objetos tales como ventanas, paredes blancas y

agua, en la zona de detección.

Fig. 1

3

Coloque el sensor lejos de objetos móviles, como por

ejemplo árboles, arbustos grandes y tráfico callejero.

No instale más de un detector de movimiento en un

interruptor de pared o circuito.

MONTAJE Y CABLEADO DEL ACCESORIO

ADVERTENCIA: Riesgo de choque eléctrico. Antes de la instalación o reparación, desconecte la alimentación eléctrica en el fusible o interrupto automático.

NOTA: El accesorio puede ser montado en la pared o el alero.

NOTA: La cubierta se adapta a las cajas eléctricas empotradas (Fig. 2). La caja eléctrica debe tener una profundidad mínima de 1-1/2 pulgadas (3,81 cm) para asegurar una instalación adecuada en aplicaciones empotradas.

1. Alinee los agujeros del soporte de montaje (H) con los agujeros de su caja de conexiones. Utilizando ya sea (2) tornillos # 6 o (2) tornillos # 8 (D)

(dependiendo del tamaño de los agujeros de su caja de conexiones), fije el soporte de montaje (H) a su caja de conexiones (Fig. 3).

2. Pase los cables del artefacto a través de la junta de la placa de cubierta (B) (Fig. 4).

3. Conecte el alambre negro del farol al alambre negro de la casa, el alambre blanco del farol al alambre blanco de la casa, y el alambre de puesta a tierra de color cobre (que sale de la placa de cierre del farol) al alambre de tierra de la casa, usando los conectores de empalme (E) suministrados.

4. Fije el artefacto (A) al soporte de montaje (H), utilizando el perno central (G) suministrado.

Asegúrese de que no se salga ningún cable por debajo de la placa cubrecables. Inserte el tapón plástico de color coincidente (F) en el agujero del tornillo para la placa de montaje, para definir el aspecto final (Fig. 5).

5. Aplique calafateo de silicona alrededor de los bordes de la placa de cubierta y en todo agujero abierto, a fin de proveer un cierre que sea estanco para la lluvia y la humedad.

6. Inserte juntas (C) en el conjunto del portalámparas, firmemente contra el portalámparas, y enrosque las lámparas en cada portalámparas (Fig. 6). (No apriete demasiado los focos.)

7. Encienda la electricidad desde la caja de fusibles/ interruptores automáticos.

OPERACIÓN DEL ACCESORIO

1. Mueva el interruptor corredizo que se encuentra en la parte inferior del sensor a “TEST”. Ajuste el botón de sensibilidad a la posición media (hasta la mitad) (Fig. 7).

2. Active la energía del portalámparas. Deje que el portalámpara se caliente aproximadamente 40 segundos antes de hacer las pruebas. (Puede que las luces no se enciendan durante el período de calentamiento.)

3. Dirija la cabeza del sensor hacia el área de detección deseada, manteniendo un ángulo de 15° hacia abajo, para permitir el drenaje de la humedad.

NOTA: Deje un espacio de aire de por lo menos

1 pulgada (2,54 cm) entre las lámparas y el sensor.

Asegúrese de que la cabeza del sensor esté colocada con los interruptores de control en dirección al piso.

4. Camine a través de la zone de detección tan lejos como desee que su detector registre movimiento.

5. Ajuste la sensibilidad hasta obtener los resultados deseados. Las luces se apagarán 4 segundos después de que todo movimiento se ha detenido.

NOTA: Para obtener un rendimiento de alcance máximo, deje que el aparato funcione en cualquiera de las modalidades (con corriente llegando a la unidad) durante al menos 48 horas.

6. Mueva el interruptor corredizo a 4 MIN o 12 MIN

(AUTO modo). Al anochecer, las luces funcionarán en el modo AUTO.

Fig. 2

1-1/2 pulgadas 1-1/2 pulgadas

Redonda

C

D

E

A

E

B

D

Fig. 3

H

Montaje de pared

Montaje de alero

TEST 4 MIN. 12 MIN.

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Octagonal

G

A

E

A

C

-

SENSITIVITY

+

F

ENERGY STAR

®

ENERGY STAR ® está patrocinado por la de EE.UU.) y el U.S.

Department of Energy (Departamento de Energía de EE.UU.).

Visite www.energystar.ca.gov para más información.

Para cumplir con los requerimientos de ENERGY STAR ® , la perilla de control del fotosensor debe estar en el modo “Auto” (automático) para evitar que esté en funcionamiento cuando haya suficiente luz de día. La potencia máxima de la bombilla no debe exceder los 250 W.

SELECCIONE LA FUNCIÓN DESEADA

Modo de funcionamiento

Adjuste de la perilla de MODO

Como adjustar interruptor electrico

Ajuste Automático

(activado por movimiento)

Las luces deberán encenderse con el movimiento únicamente durante la noche y apagarse después de 4-12 minutos que cese el movimiento.

Ajuste Amanecer-Atardecer

(activado sólo durante la noche)

Las luces deben permanecer encendidas desde el atardecer hasta el amanecer y luego restituirse a la posición de ajuste automático al amanecer siguiente.

Ajuste Estándar de Una Lámpara de Alta Intensidad

Las luces deben permanecer encendidas continuamente, durante el día y la noche

(se debe ajustar a mano).

Ajuste de Prueba

Las luces deben encenderse por el movimiento tanto en el día como en la noche. Las luces deben apagarse después de 4 segundos.

Mueva la perilla al ajuste de activación por movimiento desde cualquiera de los ajustes anteriores.

AUTO 4 MIN o

AUTO 12 MIN

AUTO 4 MIN o

AUTO 12 MIN

TEST

TEST

AUTO 4 MIN o

AUTO 12 MIN

Mantenga la alimentación del portalámparas activada.

APAGUE (OFF), ENCIENDA (ON),

APAGUE (OFF) y ENCIENDA (ON)

la corriente en menos de

3 segundos.

APAGUE (OFF), ENCIENDA (ON),

APAGUE (OFF) y ENCIENDA

(ON)

la corriente en menos de

3 segundos.

Mantenga la alimentación del portalámparas activada.

APAGUE (OFF) la corriente por al menos 40 segundos y luego

ENCIENDALA (ON) de nuevo.

DIAGNOSTICO Y SOLUCION DE PROBLEMAS

Problema Causa Posible / Acción Correctiva

Las Luces

Exteriores No Se

Encienden Durante

La Noche Aunque

Haya Movimiento

No llega electricidad al bombilla.

• Revise si el interruptor de circuito ha saltado.

• Confirme que el interruptor de pared esté encendido.

La bombilla está defectuoso.

• Cambie la bombilla.

La luz ambiental exterior es demasiado brillante. (Sí es así, para la unidad es de día).

• Redirija el cabezal.

• Cambie la ubicación de la unidad o diríjala en dirección contraria

a la luz.

DESCONECTE LA ENERGÍA ANTES DE CONTINUAR.

El cableado hacia la unidad está flojo.

• Revise los cables y vuélvalos a conectar si fuera necesario

usando las tuercas (E) que se incluyen.

Las Luces

Exteriores Se

Enciended Durante

La Noche Sin

Motivo Aparente

Hay movimiento en la zona de detección.

• Asegúrese de que el sensor no esté reaccionando a objetos

móviles tales como árboles, tráfico, etc.

COMPRUÉBELO USTED MISMO.

• Cubra la lente del sensor con un trozo de cartón para evitar

que detecte movimiento. Si las luces permanecen apa gadas,

hay algo en el área de detección que está activando el sensor.

• Si este es el caso, disminuya la sensibilidad.

• Cambie la posición del sensor de movimiento.

* Si las luces permanecen encendidas con la lente del

sensor cubierta, póngase en contacto con el servicio de

asistencia al cliente.

4

Problema Causa Posible / Acción Correctiva

Las Luces Se

Encienden Durante

La Noche Y No Se

Apagan

Hay movimiento en la zona de detección.

• Asegúrese de que el sensor no esté reaccionando a objetos

móviles tales como árboles, tráfico, etc.

• Si este es el caso, disminuya la sensibilidad.

• Cambie la posición del sensor de movimiento.

La unidad está en modo de anulación (si no hay movimiento).

• Ponga el interruptor de la luz en “OFF” durante 90 segundos

y vuel va a colocarlo en “ON”. Esto colocará de nuevo la unidad

en la modalidad “Auto” (automático).

* Si las luces permanecen encendidas con la lente del sensor

cubierta, póngase en contacto con el servicio de asistencia

al cliente.

Las Luces Se

Encienden Y

Se Apagan

Continuamente

Durante La Noche

La luz proveniente de la propia lámpara de la unidad está afectando al sensor de movimiento.

• Cambie la dirección de la lámpara.

• Cambie la posición del sensor de movimiento.

Las Luces Se

Encienden

Durante El Dia

Los controles en la base del detector de movimiento se encuentran en el modo de prueba.

• Coloque el interruptor en la modalidad 4 MIN ó 12 MIN.

Hay sombra sobre el detector de movimiento.

• Cambie la posición del sensor de movimiento.

No Se Puede

Activar La

Modalidad

De “Atardecer-

Amanecer”

(Encendido)

La luz ambiental exterior es demasiado brillante. (Sí es así, para la unidad es de día).

• Redirija el cabezal.

• Cambie la ubicación de la unidad o diríjala en dirección contraria

a la luz.

No se dejó pasar suficiente tiempo para que el accesorio entrara en el modo de amanecer-atardecer.

• APAGUE (OFF), ENCIENDA (ON), APAGUE (OFF) y ENCIENDA (ON)

la corriente en menos de 3 segundos.

Más de un accesorio está conectado en un interruptor de pared interior.

• Si es así, conéctelos en interruptores diferentes.

GARANTIA LIMITADA DE 2 AÑOS

LA SIGUIENTE GARANTÍA ES EXCLUSIVA Y REEMPLAZA A TODAS LAS DEMÁS GARANTÍAS, YA

SEAN IMPLÍCITAS, EXPLÍCITAS O ESTATUTARIAS, INCLUIDAS ENTRE OTRAS, LAS GARANTÍAS

DE COMERCIABILIDAD E IDONEIDAD PARA UN FIN PARTICULAR.

Cooper Lighting, LLC (“Cooper Lighting”) garantiza a sus clientes que los productos de Cooper

Lighting no presentarán defectos en los materiales y en la fabricación durante un período de dos años desde la fecha de compra. La obligación de Cooper Lighting según esta garantía se limita expresamente al suministro de los productos de reemplazo. Esta garantía se extiende sólo para el comprador original del producto. Un recibo del comprador u otra prueba de la fecha de compra original aceptable para Cooper Lighting. Esto es necesario para la ejecución de la garantía.

Esta garantía no se aplica a los productos de Cooper Lighting que hayan sido alterados o reparados o que estuvieron sujetos a negligencia, abuso, mal uso o accidente (incluso los daños durante el envío). Esta garantía no se aplica a los productos Cooper Lighting no fabricados por Cooper Lighting que hayan sido suministrados, instalados o utilizados junto con los productos Cooper Lighting. Los daños del producto causados por bombillas de reemplazo, corrosión o decoloración de los componentes de latón no están cubiertos por esta garantía.

LIMITACIÓN DE RESPONSABILIDAD:

COOPER LIGHTING NO SERÁ RESPONSABLE LEGAL EN NINGÚN CASO DE DAÑOS INDIRECTOS,

ACCIDENTALES O RESULTANTES (SIN IMPORTAR LA ACCIÓN LEGAL, YA SEA POR CONTRATO,

RESPONSABILIDAD ESTRICTA O DE FORMA EXTRACONTRACTUAL INCLUYENDO LA

NEGLIGENCIA) TAMPOCO DE LA PÉRDIDA DE GANANCIAS, COOPER LIGHTING TAMPOCO SERÁ

RESPONSABLE DES O DAÑOS QUE SURJAN O ESTÉN CONECTADOS CON ESTOS TÉRMINOS

O CON LA FABRICACIÓN, VENTA, ENTREGA, USO, MANTENIMIENTOM, REPARACIÓN O

MODIFICACIÓN DE LOS PRODUCTOS DE COOPER LIGHTING O DEL SUMINISTRO DE CUALQUIER

PIEZA DE REPUESTO QUE EXCEDA EL PRECIO DE COMPRA DE LOS PRODUCTOS DE COOPER

LIGHTING ORIGINANDO UN RECLAMO. NO SE ACEPTARÁN CARGOS POR MANO DE OBRA PARA

QUITAR O INSTALAR LOS ACCESORIOS.

Para obtener el servicio de la garantía comuníquese con Cooper Lighting, LLC, al

1-800-334-6871, presione la opción 2 para el Servicio al Cliente, o por correo electrónico a

[email protected] e incluya la siguiente información:

• Nombre, dirección y número de teléfono

• Fecha y lugar de compra

• Catálogo y cantidad de la compra

• Descripción detallada del problema

Todos los productos devueltos deben estar acompañados por un Número de autorización de productos devueltos emitido por la compañía y deben devolverse con flete prepagado.

Se rechazará todo producto recibido sin un Número de autorización de productos devueltos desde la compañía.

5

Cooper Lighting, LLC no se hace responsable por la mercancía dañada durante el transporte.

Los productos reparados o reemplazados estarán sujetos a los términos de esta garantía y se inspeccionan al ser empacados. El daño evidente y oculto que se provoque durante el transporte se debe informar de inmediato al transportista que realiza la entrega y se debe presentar un reclamo.

La reproducción de este documento sin la aprobación previa por escrito de Cooper Lighting, LLC está estrictamente prohibida.

Para solicitar ayuda, llame al 1-800-334-6871 o envíe un correo electrónico a [email protected]

Impreso en China

Customer First Center

1121 Highway 74 South, Peachtree City, GA 30269 www.cooperlighting.com

© 2010 Cooper Lighting, LLC

08/10

825-0448

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement