Sharp LC-20B4U Operating instructions

ENGLISH
LC-20B4U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please
record the TV’s model and serial numbers in the
space provided. The numbers are located at the
rear of the TV.
Model No.:
Serial No.:
U.S.A. ONLY
IMPORTANT INFORMATION
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
LC-20B4U(E)-a
1
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the
user to the presence of important operating and maintenance
(servicing) instructions in the
literature accompanying the
product.
03.2.26, 3:24 PM
IMPORTANT INFORMATION (Continued)
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance:
www.eia.org
2
LC-20B4U(E)-a
2
03.2.26, 3:24 PM
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety
and many years of trouble-free operation of your product, please read the Important
Safety Precautions carefully before using this product.
IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest
priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent
potential danger, please observe the following instructions when installing, operating and cleaning the
product. To ensure your safety and prolong the service life of your LCD color TV product, please read
the following precautions carefully before using the product.
■ Read instructions—All operating instructions must be read and understood before the product is
operated.
■ Keep this manual in a safe place—These safety and operating instructions must be kept in a
safe place for future reference.
■ Observe warnings—All warnings on the product and in the instructions must be observed
closely.
■ Follow instructions—All operating instructions must be followed.
■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.
■ Power source—This product must operate on a power source specified on the specification
label. If you are not sure of the type of power supply used in your home, consult your dealer or
local power company. For units designed to operate on batteries or another power source, refer
to the operating instructions.
■ Power cord protection—The power cords must be routed properly to prevent people from
stepping on them or objects from resting on them. Check the cords at the plugs and product.
■ If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a
SHARP service center or your dealer.
■ Overloading—Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.
■ Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or
short internal parts. For the same reason, do not spill water or liquid on the product.
■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to
high voltage and other dangerous conditions. Request a qualified service person to perform
servicing.
■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and
request a qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper
adjustment of controls not described in the instructions can cause damage, which often
requires extensive adjustment work by a qualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product
indicates that the product needs servicing.
■ Replacement parts—In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric
shock and/or other danger.
■ Safety checks—Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the
product according to the method recommended by the manufacturer.
■ Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
3
LC-20B4U(E)-a
3
03.2.26, 3:24 PM
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
■ Water and moisture—Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
■ Stand—Do not place the product on an unstable cart, stand,
tripod or table. Placing the product on an unstable base can
cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer’s instructions.
Use only the mounting hardware recommended by the
manufacturer.
■ When relocating the product placed on a cart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
■ Ventilation—The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface,
since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in
an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instructions are followed.
■ The Liquid Crystal panel used in this product is made of
glass. Therefore, it can break when the product is dropped
or applied with impact. Be careful not to be injured by broken
glass pieces in case the Liquid Crystal panel breaks.
■ Heat sources—Keep the product away from heat sources
such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
■ The Liquid Crystal panel is a very high technology product with 921,600 thin film transistors, giving
you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.
4
LC-20B4U(E)-a
4
03.2.26, 3:24 PM
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ If an outside antenna is connected to the television equipment, be sure the antenna system is
grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC—NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
■ Lighting – For added protection for this television equipment
during a lightning storm, or when it is left unattended and
unused for long period of time, unplug it from the wall outlet
and disconnect the antenna. This will prevent damage to the
equipment due to lightning and power-line surges.
■ Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
5
LC-20B4U(E)-a
5
03.2.26, 3:24 PM
CONTENTS
Page
IMPORTANT INFORMATION ....................................................................................................... 1, 2
DEAR SHARP CUSTOMER ............................................................................................................. 3
IMPORTANT SAFETY PRECAUTIONS ....................................................................................... 3-5
CONTENTS ....................................................................................................................................... 6
SUPPLIED ACCESSORIES ............................................................................................................. 7
PREPARATION ............................................................................................................................ 8-10
Using the Remote Control ......................................................................................................... 8
Batteries for the Remote Control .............................................................................................. 8
Antenna Connection ............................................................................................................. 9, 10
Power Connection .................................................................................................................... 10
DISPLAY AND CONTROL OVERVIEW .................................................................................. 11-13
Removing the Back Cover ....................................................................................................... 13
Listening with Headphones ..................................................................................................... 13
REMOTE CONTROL ...................................................................................................................... 14
EZ SETUP (WITH AUTO CLOCK SETTING) .......................................................................... 15, 16
EZ SETUP during the First Power On .............................................................................. 15, 16
SETTING THE CLOCK ............................................................................................................. 17-19
AUTO CLOCK Setting ......................................................................................................... 17, 18
MANUAL CLOCK Setting ......................................................................................................... 19
BASIC OPERATION ................................................................................................................. 20-24
TV signals in your region ........................................................................................................ 20
Turning on POWER ................................................................................................................... 21
Standby ...................................................................................................................................... 21
Switching TV/VIDEO [AV1/AV2/COMPONENT/TV] Modes ................................................... 22
Sound Volume ........................................................................................................................... 23
Changing Channels .................................................................................................................. 24
SELECTING MENU ITEMS ............................................................................................................ 25
Selecting Menu Items .............................................................................................................. 25
ADJUSTMENTS ........................................................................................................................ 26-43
Adjusting SLEEP TIMER Settings ........................................................................................... 26
Adjusting BRIGHTNESS Settings ........................................................................................... 27
Adjusting PICTURE FLIP Settings .......................................................................................... 28
Adjusting PRESET Settings .................................................................................................... 29
Adjusting LANGUAGE Settings .............................................................................................. 30
Adjusting VIDEO ADJUST Settings .................................................................................. 31, 32
SET UP .................................................................................................................................33, 34
Adjusting BLUE SCREEN Settings ......................................................................................... 35
Adjusting CLOSED CAPTION Settings .................................................................................. 36
Adjusting V-CHIP Settings ..................................................................................................37-43
CONNECTING EXTERNAL DEVICES ..................................................................................... 44-46
Bundling Cables with Clamps ................................................................................................ 46
TROUBLESHOOTING .............................................................................................................. 47, 48
SPECIFICATIONS ........................................................................................................................... 49
DIMENSIONAL DRAWINGS .......................................................................................................... 50
CALLING FOR SERVICE ............................................................................................................... 51
LIMITED WARRANTY .............................................................................................................. 51, 52
6
LC-20B4U(E)-a
6
03.2.26, 3:24 PM
SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the product.
Remote Control
“AAA” size (UM/SUM-4) Dry Battery (×2)
RRMCGA152WJSA (LC-20B4US)
RRMCGA152WJSB (LC-20B4UB)
Antenna Cable
AC Cord
QCNWG0003CEPA
QACCD3097CEPA
Operation Manual
Cable Clamp (×2)
PORTUGUÊS
ESPAÑOL
FRANÇAIS
ENGLISH
AC Adapter
UADP-0212CEZZ
UADP-0243CEPZ
UBATU0026GEZZ
TINS-A691WJZZ
LHLDWA002WJSA
(LC-20B4US)
LHLDWA002WJSB
(LC-20B4UB)
7
LC-20B4U(E)-a
7
03.2.26, 3:24 PM
PREPARATION
Using the Remote Control
■ Use the remote control by pointing it towards the remote
POWER SLEEP
control sensor window on the main unit. Objects between
the remote control and sensor window may prevent proper
operation.
SLEEP indicator
POWER indicator
Cautions regarding use of the remote control
Remote control
sensor
■ Do not expose the remote control to shock.
In addition, do not expose the remote control to liquid, and
do not place in an area with high humidity.
■ Do not install or place the remote control under direct
sunlight. The heat may cause deformation of the unit.
■ The remote control may not work properly if the remote
control sensor window of the main unit is under direct
sunlight or strong lighting. In such case, change the angle of
the lighting or LCD TV set, or operate the remote control
closer to the remote control sensor window.
Batteries for the Remote Control
Before using the LCD TV set for the first time, install two (“AAA” size, UM/SUM-4) batteries (supplied).
When the batteries become depleted and the remote control fails to operate, replace the batteries with
new (“AAA” size, UM/SUM-4) batteries.
1
2
Open the battery
cover.
Insert two (“AAA” size, UM/
SUM-4) batteries.
3
Close the battery
cover.
–
+
+
–
■ Position the positive and
negative ends of the batteries
as indicated in the compartment.
■ Slide the cover while
pressing the (b) part.
■ Engage the claw on the
cover into the battery
housing and slide shut.
Caution!
Cautions regarding batteries
Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) as indicated in the compartment.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new
battery and/or cause the old battery to leak chemicals.
• Remove batteries when they become weak.
Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a
cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control will not be used for an extended period of time, remove the batteries from the
remote control.
8
LC-20B4U(E)-a
8
03.2.26, 3:24 PM
PREPARATION (Continued)
Antenna Connection
ANTENNAS
• The antenna requirements for good color television reception are more important than those for black & white
television reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna
systems.
F-type connector
1. A 75-ohm system is generally a round cable with F-type
connector that can easily be attached to a terminal without
tools (not supplied).
75-ohm coaxial cable (round)
2. A 300-ohm system is a flat “twin-lead” cable that can be
attached to a 75-ohm terminal through a 300-75-ohm
adapter (not supplied).
300-ohm twin-lead cable (flat)
OUTDOOR ANTENNA CONNECTION
• Use one of the following two diagrams if you connect an outdoor antenna.
A: Using a VHF/UHF combination outdoor antenna
B: Using separate VHF and/or UHF outdoor antennas
• Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the TV set.
A. Combination VHF/UHF Antenna
300/75-ohm
adapter
(not supplied)
VHF/UHF
antenna
VHF/UHF
antenna
or
300-ohm
twin-lead
CH
MENU TV/VIDEO
MAIN POWER
VOL
75-ohm
coaxial cable
Antenna cable (supplied)
B. Separate VHF and/or
UHF Antennas
UHF
antenna
VHF
antenna
300-ohm
twin-lead
ANT.
ANT. (Antenna
terminal)
Combiner
(not supplied)
OUT
300-ohm
twin-lead
IN
75-ohm
coaxial cable
POWER
INPUT
DC13V
or
9
LC-20B4U(E)-a
9
03.2.26, 3:24 PM
PREPARATION (Continued)
Antenna Connection (Continued)
CABLE TV (CATV) CONNECTION
• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. terminal.
• Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay
channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber
by the cable TV company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set your TV to channel 3 or 4, typically one of these channels is used. If this
is unknown, consult your cable TV company.) For more specific instructions on installing cable TV,
consult your cable TV company. One possible method of utilizing the converter/descrambler
provided by your cable TV company is explained below.
Please note: An RF switch provided with two inputs (A and B) is required (not supplied).
“A” position on the RF switch (not supplied): You can view all unscrambled channels by using the TV’s
channel keys.
“B” position on the RF switch (not supplied): You can view the scrambled channels via the converter/
descrambler by using the converter’s channel keys.
RF switch (not supplied)
Two-set
signal
splitter
(not
supplied)
OUT
Cable TV Line
IN
Cable TV converter/
descrambler
(not supplied)
A
• Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be
required.
Power Connection
MAIN POWER
ANT.
CH
MENU TV/VIDEO
MAIN POWER
VOL
POWER
INPUT
DC13V
POWER INPUT
terminal (DC13V)
Household power outlet
AC adapter
AC cord
A
• Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet.
• Always turn the MAIN POWER switch of the LCD TV set to off when connecting the AC adapter.
• Unplug the AC adapter from the product and power outlet when not using for a long period of time.
10
LC-20B4U(E)-a
10
03.2.26, 3:24 PM
DISPLAY AND CONTROL OVERVIEW
Controls
Upper control panel
VOL (–)/(+)
CH ( )/( )
MENU
TV/VIDEO
MAIN POWER
VOL
CH
MENU TV/VIDEO
MAIN POWER
Speaker (Left)
Speaker (Right)
To change the vertical
angle of the LCD TV set,
tilt the screen up to 5
degrees forward or 10
degrees backward. The
TV set can also be
rotated 50 degrees
horizontally. Adjust the
angle so that the TV set
can be watched most
comfortably.
Remote control sensor
POWER indicator
A green indicator lights when the power is
on and a red indicator lights when in the
standby mode (the indicator will not light
when the main power is off).
SLEEP indicator
The SLEEP indicator lights up red when the
SLEEP TIMER is set.
A
• TV/VIDEO, CH ( )/( ), VOL (–)/(+), and MENU on the main unit have the same functions as the same buttons
on the remote control. Basically, this operation manual provides a description based on operation with the remote
control.
11
LC-20B4U(E)-b
11
03.2.26, 3:25 PM
DISPLAY AND CONTROL OVERVIEW (Continued)
● Adjusting the screen view angle
Terminals
ONENT
Y
COMP
PB
PR
L
AUDIO
R
(L)
(R)
AV-IN2/OUT
Hold the carrying handle and tilt the
screen while steadying the stand with
your other hand.
COMPONENT
(L)
(R)
MENU TV/VIDEO
AUDIO
R
VIDEO
AUDIO
AUDIO
Y
PB
PR
AUDIO
AUDIO
CH
VIDEO
UT
AV-IN2/O
L
MAIN POWER
VOL
Carrying handle
VIDEO
AV-IN1
AUDIO (L)
AUDIO (R)
S-VIDEO
HEADPHONE
ANT. (Antenna terminal)
POWER INPUT
(DC13V)
12
LC-20B4U(E)-b
12
03.2.26, 3:25 PM
VIDEO
AV-IN
L
AUDIO
R
S-VIDE
O
HEAD
PHONE
ANT.
POWER
INPUT
DC13V
1
DISPLAY AND CONTROL OVERVIEW (Continued)
Removing the Back Cover
■ Before connecting cables and cords to the rear terminals, remove the
back covers. Push in the tabs and pull out the back covers carefully.
CH
MENU TV/VIDEO
MAIN POWER
VOL
■ To mount the cover, insert the 2 hooks on the bottom of the cover
into the cabinet and press on the upper part of the back cover until
the tab locks in place with a click.
Listening with Headphones
■ Plug the headphone mini-plug into the HEADPHONE jack located on the rear of the TV set.
▼ On-screen display
MENU TV/VIDEO
CH
MAIN
VOL
c Rear terminal
VOLUME
20
Headphones
Adjust the sound volume
using VOL (e)/(f) on the
remote control.
A
• Headphones are not included in the supplied accessories.
• No sound is heard from the main unit speakers when a headphone mini-plug is connected into the
HEADPHONE jack.
13
LC-20B4U(E)-b
13
03.2.26, 3:25 PM
REMOTE CONTROL
1 POWER (p. 21)
1
2
3
4
5
6
7
Switch the Liquid Crystal Television power
on or off.
POWER
10
DISPLAY
SLEEP
Display the channel and time information.
PIC. FLIP
11
BRIGHT TV/VIDEO MENU
FLASHBACK
VOL
CH
3 SLEEP (p. 26)
Set the sleep timer.
ENTER
MUTE
2 DISPLAY
12
4 ENTER
13
14
5 BRIGHT (p. 27)
Execute a command.
Adjust the brightness of the screen.
6 MUTE (p. 23)
8
Mute the sound.
15
7 VOL (+)/(–) (p. 23)
Set the volume.
8 CH ( )/( ) (p. 24)
9
Select channel.
9 MTS (p. 23)
Select audio settings.
10 PIC. FLIP (p. 28)
Set the orientation of the picture.
11 a/b/c/d (Cursor control) (p. 25)
Select a desired item on the screen.
12 TV/VIDEO (p. 22)
Select a Liquid Crystal Television input
source.
13 MENU (p. 25)
Display the menu screen.
14 FLASHBACK
Return to the previous channel.
15 Channel Select (p. 24)
Set the channel.
14
LC-20B4U(E)-b
14
03.2.26, 3:25 PM
EZ SETUP (WITH AUTO CLOCK SETTING)
EZ SETUP during the First Power On
■ When you turn on the TV for the first time, it will automatically
memorize the broadcasting channels and clock.
Please perform the following instructions before you press MAIN
POWER.
(1) Insert the batteries into the remote control. (See page 8.)
(2) Connect the antenna cable to the TV set. (See page 9.)
(3) Connect the AC adapter to the POWER INPUT terminal of the
product and plug in the AC cord to the wall outlet. (See page 10.)
Control section of main unit
MAIN POWER
VOL
MENU TV/VIDEO
CH
MAIN POWER
1
Press MAIN POWER, located on
the upper side of the main unit, to
turn on the TV. The SELECT
LANGUAGE mode will be displayed.
2
Press a/b to select “ENGLISH”,
“ESPAÑOL (SPANISH)” or
“FRANCAIS (FRENCH)”, and press
ENTER.
3
POWER
Press a/b to select ON or OFF.
When you select ON, the TV set
will automatically memorize the
broadcasting channels.
SE L EC T LANGUAGE
ENGL I SH
ESPAÑOL
FRANCA I S
SELECT :
ENTER :
ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
E Z SE TUP
CH - SE T T I NG
ON
OFF
DISPLAY
SLEEP
Press ENTER to access AUTO
CLOCK mode.
PIC. FLIP
ENTER
MUTE
BRIGHT TV/VIDEO MENU
FLASHBACK
VOL
CH
ENTER/
a/b/c/d
4
SELECT :
Press a/b to select ON or OFF.
When you select ON, the TV set
will automatically adjust the clock
to search time-signals (EDS
signals), which are provided by
some TV stations. If you know the
channel of the EDS signal carrier in
your area, select OFF and follow
the procedure in AUTO CLOCK
Setting. (See pages 17, 18)
MENU
5
ENTER :
ENTER
E Z SE TUP
AUTO CLOCK
ON
OFF
SELECT :
ENTER :
ENTER
Press ENTER to access start EZ
SETUP mode.
A
• If you select OFF in “EZ SETUP CH-SETTING”, EZ SETUP will be canceled.
15
LC-20B4U(E)-b
15
03.2.26, 3:26 PM
EZ SETUP (WITH AUTO CLOCK SETTING) (Continued)
EZ SETUP during the First Power On (Continued)
6
POWER
DISPLAY
SLEEP
ENTER
BRIGHT TV/VIDEO MENU
FLASHBACK
VOL
CH
CONNECT ANTENNA OR CABLE.
If you want to stop the EZ SETUP
process once it has started, press
c and it will be canceled. If you
want to SET UP again, please refer
to pages 33 and 34 on SET UP.
PIC. FLIP
MUTE
Press a/ b to select YES, and
press ENTER.
ENTER/
a/b/c/d
To cancel EZ SETUP
START EZ SETUP?
YES
NO
SELECT :
ENTER :
ENTER
EX I T :
MENU
Press c.
MENU
The tuner will automatically search
for the broadcasting and cable TV
channels. (The CH No. will
automatically increase when it
appears.)
PLEASE WA I T
AUTO PROGRAMMI NG
STOP :
The TV set will automatically switch
to searching for EDS signals.
PLEASE WA I T
NOW SEARCH I NG T IME
If EDS signals are received, the
channel number and time will be
displayed, and then the screen
shown in step 7 appears.
STOP
7
Once EZ SETUP is completed, the
lowest channel number memorized
will be displayed.
2
STEREO < ON A I R
SAP
MONO
11 : 53AM
A
• Do not let the EZ SETUP screen remain unattended for a long time.
• If EZ SETUP does not memorize all the channels in your region, please refer to pages 33 and 34 for more
information on manually memorizing the channels using CHANNEL SETTING.
• It may be difficult to preset when the broadcasting signals are weak, the channel cycle frequency is incorrect or
the frequency jamming is occurring around the area. Please refer to pages 33 and 34 for more information on
manually memorizing channels using CHANNEL SETTING.
• CLOCK: AUTO CLOCK Setting may take several minutes to execute depending on the number of channels to
receive and status of signals.
• If there are no channels with EDS signals or the antenna signal is weak, the AUTO CLOCK Setting may not
operate. In this case, a “EDS CH IS NOT AVAILABLE” message will display and the mode will change to MANUAL
CLOCK Setting. Refer to page 19 to set the clock manually.
16
LC-20B4U(E)-b
16
03.2.26, 3:26 PM
SETTING THE CLOCK
AUTO CLOCK Setting
There are two methods of setting the clock: AUTO CLOCK and MANUAL CLOCK. AUTO CLOCK uses
EDS signals, which are provided by some TV stations, to automatically adjust the clock. MANUAL CLOCK
set the clock manually in areas where no channel carries EDS signals.
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
SET UP, and press ENTER.
POWER
DISPLAY
SLEEP
PIC. FLIP
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
ENTER
MUTE
BRIGHT TV/VIDEO MENU
FLASHBACK
VOL
CH
ENTER/
a/b/c/d
SELECT :
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
MENU
3
Press a/b to move the cursor to
CLOCK, and press ENTER.
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
SELECT :
4
Press a/b to move the cursor to
AUTO CLOCK, and press ENTER.
ENTER : ENTER
CLOCK
RETURN
AUTO CLOCK
MANUAL CLOCK
OFF
SELECT :
ENTER : ENTER
A
• The CLOCK can be stopped completely by setting CLOCK to “OFF”.
Time reset for power outage, AC adapter disconnected
If the TV has a power outage or the AC adapter cord is disconnected, the time display will have to
be reset. In that case, refer to SETTING THE CLOCK on pages 17 to 19.
17
LC-20B4U(E)-b
17
03.2.26, 3:26 PM
SETTING THE CLOCK (Continued)
AUTO CLOCK Setting (Continued)
5
Press c/d to select AUTO or
MANUAL.
6
Press a/b to move the cursor to
START, and press ENTER.
POWER
AUTO CLOCK
RETURN
EDS CH SET [AUTO ]
EDS CH
[ ––– ]
START
DISPLAY
SLEEP
PIC. FLIP
ENTER
MUTE
BRIGHT TV/VIDEO MENU
FLASHBACK
VOL
CH
ENTER/
a/b/c/d
ADJUST :
ENTER : ENTER
EX I T :
MENU
PLEASE WA I T
MENU
NOW SEARCH I NG T IME
● If you do not know the channel that
carries EDS signals in your area,
select EDS CH SET to AUTO and
select START. If you know the
channel of the EDS signal carrier in
your area, select EDS CH SET to
MANUAL. Set the EDS CH and
select START.
● When set to “AUTO CLOCK”, the
time is acquired automatically when
MAIN POWER is turned OFF. (This
function will not work when EDS
CH is not set.)
STOP
2
STEREO < ON A I R
SAP
MONO
11 :