XLT42E
TWO-WAY COMPACT TRAPEZOIDAL
LOUDSPEAKER WITH 90° X 40° HF HORN
S
PECIFICATIONS (See notes 1 and 2)
Loudspeaker Type:
Operating Range:
2-way, Full-range, bass ported
70 Hz - 18 kHz
70 Hz - 18 kHz (+/-5dB)
Max Input (Passive): 200W continuous, 500W program
40 volts RMS, 89 volts momentary peak
Recommended Power Amp:
420W to 600W @ 8 Ohms
Max Inputs (Biamp):
LF: (Same as for Passive mode)
Recommended LF Power Amp: (Same as for Passive mode)
HF: 50W continuous, 125W program
20 volts RMS, 45 volts momentary peak
Recommended HF Power Amp: 100W to 150W @ 8 Ohms
Sensitivity 1W/1m:
97dB SPL (70 Hz - 16 kHz 1/3 octave bands)
96dB SPL (250 Hz - 4 kHz speech range)
Maximum Output: 120 dB SPL / 127 dB SPL (peak)
Nominal Impedance (passive): 8 Ohms
Min Impedance: 5.6 Ohms @ 180 Hz
Nominal Impedances (Biamp): LF: 8 Ohms, HF: 8 Ohms
Nominal -6 dB Beamwidth:
80° H (+3° / -11°, 2 kHz - 10 kHz)
35° V (+8° / -2°, 2 kHz - 10 kHz)
Axial Q / DI:
22.2 / 13.5, 2 kHz - 10 kHz
Crossover Frequency: 2 kHz
Recommended Signal Processing: 60 Hz high pass filter
Drivers:
LF (1) 12", Ferrofluid-cooled
HF (1) 1" exit, titanium diaphragm
Driver Protection: PowerSense™ DDP
Input Connection: (2) Neutrik NL4MP
(2) 1/4 inch jack
Controls: Passive / Biamp switch
2 position HF level switch
Enclosure: 13-ply 18 mm Baltic birch, Polane painted
Enclosure Hardware:
(1) Steel recessed spring handle
(4) Heavy-duty rubber feet
Mounting / Rigging Provisions:
(6) 3/8-16 rigging points, W.L.L. 150 lb. vertical pull each
(1) 1-3/8" pole socket
Grille: 16 gauge perforated steel (see options)
Required Accessories: None
Supplied Accessories: None
Optional Accessories:
EYBLTKIT: (4) 3/8-16 forged eyebolts
SB5: black 5 ft x 1-3/8" steel pole for mounting to a subwoofer
Dimensions (including feet):
Height: 24.3 in. / 618 mm (23.9 in. / 608 mm w/o feet)
Width (front): 14.6 in. / 371 mm
Width (rear): 9.2 in. / 234 mm
Depth: 14.75 in. / 375 mm
Weight:
Shipping Weight:
53.5 lb. / 24.3 kg
57 lb. / 25.9 kg
1. Sensitivity: Free field pink noise measurement at 20 feet (6.1m) at
25% power; extrapolated to 1 meter and an input of 2.83 volts RMS.
2. Watts: All wattage figures are calculated using the rated nominal impedance.
24.3 in.
618 mm
A PPLICATIONS :
• Theatres / Auditoria
• Houses of Worship
• Sport Facilities
• Health Clubs
• Clubs
• A/V Systems
F EATURES :
• 1” Titanium HF Driver with HF Level Switch
• Ferrofluid-cooled 12” LF
• Switchable Passive / Biamp Modes
• PowerSense™ DDP Circuit with Front/Rear Indicators
• Trapezoidal Enclosure for Arraying
• Steel Handle and Input Panel
• Black Paint Exterior
• Stand Socket
D ESCRIPTION
The XLT42E is a small and versatile two-way full-range bass reflex loudspeaker system engineered for multiple uses in club and performance public address. This system has a rotatable HF horn. Availability of both captive rigging points and provision for a stand adapter allow this system to be used effectively in both portable and installed situations. The black-painted 13-ply Baltic birch enclosure and black perforated steel grille present an attractive package. Features an over-drive indicator light and a passive / biamp switch on the input panel, PowerSense protection circuitry and a Ferrofluid cooled woofer. Five year warranty.
XLT42E Page 1 of 2
© 1999, Community Light & Sound, Inc.
F REQUENCY R ESPONSE
120
Resolution <500 Hz = 10 Hz, >500 Hz = 40 Hz, 1/8 octave smoothing
110
100
90
80
70
10 100 1,000
Frequency in Hertz
10,000
B
EAMWIDTH
Horizontal Vertical
1000
XLT42E
TWO-WAY COMPACT TRAPEZOIDAL
LOUDSPEAKER WITH 90° X 40° HF HORN
I MPEDANCE
40
32
24
16
8
0
10
A
XIAL
Q
100
Min Z 70 Hz - 20000 Hz = 5.6 Ohms @ 180 Hz
100 1,000
Frequency in Hertz
10,000
100
10
100
D IMENSIONS
1,000
Frequency in Hertz
10,000
10
1
100 1,000
Frequency in Hertz
10,000
A RCHITECTS ' A ND E NGINEERS ' S PECIFICATIONS
The loudspeaker system shall be a two-way, full-range bass reflex trapezoidal design with one 12 in. Ferrofluid-cooled woofer and one 1 in. exit HF driver with a titanium diaphragm mounted to a 90° HF fiberglass horn. Drivers shall be connected to an integral crossover with a crossover frequency of 2 kHz and integral over-current protection circuitry using high positive current coefficient resistors. There shall be two NL4MP connectors and two 1/4" phone jack connectors with a switch for passive or biamplified connection and rear-facing LED over-power indicator light. The loudspeaker enclosure shall be 13-ply Baltic birch plywood with a 16 gauge perforated steel grille and finished with black paint. The system shall have an amplitude response of 70 Hz to 18 kHz (+/- 5 dB), input capability of 40V RMS, 97 dB sensitivity at one meter and 2.83V / 8 ohms nominal impedance. The nominal dispersion shall be 80° H x 35° V from 2 kHz to 10 kHz. The loudspeaker shall be 24.3 in.
(618 mm) H x 14.6 in. (371 mm) W (front) x 9.2 in. (234 mm) W (rear) x 14.75 in. (375 mm) D and weigh 53.5 lbs (24.3 kg).
Specifications subject to change without notice.
XLT42E Page 2 of 2
XE42-991020