Bosch ICP-CC404 User`s guide

ICP-CC404
User’s Guide
EN
ICP-CC404
Control Panel
ICP-CC404 | User's Guide | Copyright Notice
Copyright Notice
New Zealand Telepermit Notes
Unless otherwise indicated, this publication is the
copyright of Bosch Security Systems, Inc. (“Bosch”).
All rights are reserved.
The grant of a telepermit for a device in no way
indicates Telecom acceptance of responsibility for the
correct operation of that device under all operating
conditions.
You may download a single copy of this publication.
By downloading the publication you agree that you
will: (i) only use the publication for your own
reference; (ii) not commercially exploit or charge any
person for the use of the publication; and (iii) not
modify the publication in any way without the prior
written permission of Bosch.
Except as specified above or where authorized by the
Copyright Act 1968 (Cth), no part of this publication
may be reproduced, transmitted, modified or stored,
in any form or by any means, without the prior
written permission of Bosch.
This equipment will not be used in any manner that
could constitute a nuisance to other telecom
customers.
Immediately disconnect this equipment should it
become physically damaged and arrange for its
disposal or repair.
Notice of Liability
The transmit level from this device is set at a fixed
level and because of this, there may be circumstances
where the performance is less than optimal. Before
reporting such occurrences as faults, please check the
line with a standard telepermitted telephone and do
not report a fault if the telephone performance is
satisfactory.
This material is designed for use by tradespeople with
expertise in the installation of this product. Persons
without appropriate expertise should seek assistance
before attempting installation.
This device is equipped with pulse dialing while the
Telecom standard is DTMF tone dialing. There is no
guarantee that Telecom lines will always continue to
support pulse dialing.
While care was taken in the preparation of this
material, Bosch Security Systems, Inc. and its
representatives are not responsible to any person or
entity for any loss or damage directly or indirectly
caused by information in, or any omission from, this
material.
Use of dialing, when this equipment is connected to
the same line as other equipment, may give rise to
bell noise and also cause a false answer condition.
Should such problems occur, the user should not
contact the Telecom Faults Service.
Bosch Security Systems, Inc. reserves the right to
make changes to features and specifications of its
products at any time without prior notification.
This equipment is set up to carry out test calls at predetermined times. Such test calls interrupt any other
calls that may be set up on the line at the same time.
The timing set for such test calls should be discussed
with the installer.
The timing set for test calls from this equipment may
be subject to drift. If this proves to be inconvenient
and your calls are interrupted, then the problem of
timing should be discussed with the equipment
installer. The matter should not be reported as a fault
to Telecom Faults Service.
This equipment shall not be set up to make automatic
calls to the Telecom 111 Emergency Service.
This equipment should not be used under any
circumstances that may constitute a nuisance to other
Telecom customers.
In the event of any problem with this device, the
systems battery, AC MAINS supply, and telephone
line should be disconnected. The user is to arrange
with the supplier of the device to make the necessary
repairs.
Should the matter be reported to Telecom as a wiring
fault and the fault proven to be due to this product, a
call-out charge will be incurred.
2
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | Contents
Contents
1.0
Introduction ......................................................4
2.0
Features..............................................................4
3.0
Codepad Indicators .........................................5
3.1
Zone Indicators...................................................5
3.2
AWAY Indicator................................................5
3.3
STAY Indicator ..................................................5
3.4
System Disarmed................................................5
3.5
MAINS Indicator ...............................................6
3.6
Off Indicator/Zone Sealed ................................6
3.7
On Indicator/Zone in Alarm ............................6
3.8
FAULT Indicator ...............................................6
3.9
Audible Indications............................................6
4.0
Arming the System ..........................................6
4.1
Arming in AWAY Mode...................................7
4.2
Arming in STAY Mode 1..................................7
4.3
Arming in STAY Mode 2..................................7
4.4
Programming STAY Mode 2 Zones ................8
5.0
Disarming the System .....................................8
6.0
User Codes ........................................................8
6.1
Adding User Codes............................................8
6.2
Adding Radio Remote User Codes..................8
6.3
Deleting User Codes/Radio User Codes.........8
7.0
Radio Transmitter Operations......................9
8.0
Alarms ................................................................9
8.1
Duress Alarm......................................................9
8.2
Panic Alarm ........................................................9
8.3
Fire Alarm.........................................................10
8.4
Medical Alarm..................................................10
8.5
Tamper Alarm (Access Denied) .....................10
9.0
Isolating Zones ...............................................10
9.1
Standard Isolating ............................................10
9.2
Code to Isolate .................................................10
10.0
Setting the Date and Time...........................10
11.0
Fault Analysis Mode......................................11
11.1
AC Fail ..............................................................11
11.2
System Faults ....................................................11
11.3
Fault Descriptions.............................................11
12.0
Telco Arm/Disarm Sequence (Call
Forward On/Off) ..........................................................11
12.1
Telco Arm Sequence........................................11
12.2
Telco Disarm Sequence...................................12
13.0
Turning Outputs On/Off ..............................12
14.0
Reset Latching Outputs ................................12
15.0
Codepad ID/Buzzer Tone Change ............12
16.0
Testing..............................................................13
16.1
Horn Speaker Test ...........................................13
16.2
Bell Test.............................................................13
16.3
Strobe Test ........................................................13
16.4
Walk Test Mode...............................................13
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
16.5
17.0
18.0
19.0
20.0
20.1
20.2
20.3
21.0
22.0
23.0
24.0
Test Report .......................................................13
Event Memory Recall ...................................13
Day Alarm.......................................................13
Remote Arming By Telephone...................13
Domestic Dialing ...........................................14
Acknowledging Domestic Calls......................14
Programming Domestic Telephone Numbers14
Disable Domestic Dialing................................14
Basic Pager Reporting ..................................14
Glossary of Terms..........................................17
Installation Notes ...........................................19
Specifications..................................................22
Figures
Figure 1:
Figure 2:
Figure 3:
Figure 4:
Figure 5:
Figure 6:
ICP-CP508W Eight Zone LED Codepad 5
ICP-CP508LW Eight Zone LCD
Codepad....................................................... 5
RE012/E: 2-Channel Keyfob
Transmitter .................................................. 9
RE013/E: 4-Channel Keyfob
Transmitter .................................................. 9
ICP-CP508W LED Codepad Showing
Audible Alarm Buttons .............................. 9
Basic Pager Display ..................................16
Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Zone Indicators ........................................... 5
AWAY Indicator......................................... 5
STAY Indicator........................................... 5
MAINS Indicator........................................ 6
FAULT Indicator ........................................ 6
Audible Indicators ...................................... 6
Arming Methods......................................... 6
Keyfob Audible and Visual Indications ... 9
Fault Condition Indicators .......................11
Telco Arm/Disarm Dialing Digits...........12
Domestic Dialing Telephone Digits........14
Zone Status Display Descriptions............15
System Status.............................................15
Glossary of Terms.....................................17
Specifications .............................................22
3
ICP-CC404 | User's Guide | 1.0
Introduction
1.0 Introduction
2.0 Features
Congratulations on selecting the ICP-CC404 Control
Panel to protect you and your property. To get the
most from your unit, read through this manual and
familiarize yourself with the operating features of this
system. In all aspects of planning, engineering,
styling, operation, convenience, and adaptability, we
have sought to anticipate your every possible
requirement.
The ICP-CC404 Control Panel uses the latest in
microprocessor technology to provide you with more
useful features, and superior reliability and
performance. The main features of the control panel
are:
• Eight programmable User Codes
• STAY Mode and AWAY Mode operation
• Four programmable burglary zones
• Four programmable 24-hour zones
• Siren and/or dialer lockout per zone
• Delayed reporting
• Built-in telephone fail monitor
• Day alarm
• Remote arming
• Answering machine bypass
• Upload/download programmable
• Auxiliary output (Output 2)
• Relay output
• Eight radio remote user codes
• Entry and Exit Warning beeper
• EDMSAT – satellite siren compatible
• Separate fire alarm sound
• Dual reporting
• Sensor watch
• Dynamic battery testing
• Automatic arming and disarming
• AC fail and system fault indicators
• Walk Test Mode
• Monitored siren output (Output 1)
• Strobe output
• Telco arm and disarm sequence (call forwarding)
• 40 events in non-volatile memory
Programming simplicity and speed were some of the
major considerations and we believe that our
objectives in this area were more than satisfied.
This guide explains all aspects of operating the
control panel. All system parameters and options are
detailed. Suitability is left up to the individual. Every
system can be tailored to meet all requirements
quickly and easily.
4
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 3.0
Codepad Indicators
3.0 Codepad Indicators
3.2
AWAY Indicator
The AWAY indicator shows the system
is armed in AWAY Mode. The AWAY
indicator also flashes in unison with the
STAY indicator when programming
the control panel.
Figure 1: ICP-CP508W Eight Zone LED
Codepad
Refer to Section 4.1 Arming in AWAY
Mode on page 7 for information on the
different methods of arming the system
in AWAY Mode.
Table 2: AWAY Indicator
Figure 2: ICP-CP508LW Eight Zone LCD
Codepad
Status
Definition
On
Off
System is armed in AWAY Mode.
System is not armed in AWAY Mode.
3.3
STAY Indicator
The STAY indicator shows the system is
armed in STAY Mode 1 or STAY
Mode 2. The STAY indicator also flashes
in unison with the AWAY indicator
when programming the control panel.
Refer to Section 4.2 Arming in STAY Mode
1 on page 7 and Section 4.3 Arming in
STAY Mode 2 on page 7.
Table 3: STAY Indicator
The codepad is the communications interface
between you and your alarm system. Use the
codepad to issue commands. The codepad offers
both visual and audible indications that guide you
through general operation.
The codepad incorporates a number of indicators.
Eight zone indicators show the status of each zone
and four other indicators show general status.
3.1
Zone Indicators
1 2 3 …. The zone indicators (1 to 8) display
the status of the zones. Table 1 lists the
status that the indicators display (such
as, Zone Sealed/Zone Unsealed).
Status
Definition
On
System is armed in STAY Mode
1 or STAY Mode 2.
System is not armed in STAY
Mode 1 or STAY Mode 2.
Zone Isolating Mode or setting
STAY Mode 2 zones.
Day alarm status – day alarm
turned on.
Off
Flashing twice a sec
Flashing once every
3 sec
3.4
System Disarmed
indicator light
This indicator and the
when the system is disarmed.
Table 1: Zone Indicators
Status
Definition
On
Off
Flashing fast
(0.25 sec on/
0.25 sec off)
Flashing slow
(1 sec on/1 sec off)
Zone is unsealed.
Zone is sealed.
Zone is in alarm.
Zone is manually isolated or
selected to be isolated.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
5
ICP-CC404 | User's Guide | 4.0
3.5
Arming the System
MAINS Indicator
The MAINS indicator shows if the
systems AC MAINS supply is normal or
failed.
Table 6: Audible Indicators
Indicator
Definition
One short beep
A button was pressed on the
codepad, or end of Exit Time
occurred when armed in STAY
Mode 1 or STAY Mode 2.
The system accepted your code.
The system executed the requested
function.
Indicates the end of Exit Time when
armed in AWAY Mode, or the
requested operation was denied or
aborted.
Walk Test Mode is currently active
or it is a warning before automatic
arming takes place.
There is a system fault waiting to be
acknowledged.
Table 4: MAINS Indicator
Status
Definition
On
Flashing
AC MAINS power normal.
AC MAINS supply failed.
3.6
On Indicator/Zone in Alarm
The
indicator lights when the
system is armed in AWAY Mode and
flashes when an alarm occurs. The
system resets this indicator after you
enter a valid user code.
3.8
One long beep
Off Indicator/Zone Sealed
indicator lights when the
The
system is disarmed and flashes when a
zone becomes unsealed when
disarmed. The indicator stops flashing
when all zones are sealed.
3.7
Two short beeps
Three short beeps
FAULT Indicator
The FAULT indicator lights if the
system detects a system fault. Refer to
Section 11.0 Fault Analysis Mode on
page 11 for additional information on
system faults.
Every time a new system fault is
detected (the FAULT indicator flashes),
the codepad beeps once every min.
Pressing [#] once cancels the once a
min beep and acknowledges the fault
(the FAULT indicator lights steadily).
Table 5: FAULT Indicator
One beep every
sec
One short beep
every min
4.0 Arming the System
There are several ways to arm the system depending
on whether you are:
• Leaving the premises and you want all active
zones to be in a ready state for an intruder.
• Remaining in the premises and you only want
part of the system to be in a ready state for an
intruder.
If a zone is not sealed at the end of Exit Time, the
zone is automatically isolated and lights steadily on
the remote codepad. The zone becomes an active
part of the system when the zone is resealed. For
example, if a window is left open after Exit Time
expires, the window is not an active part of the
system until the window is closed. Opening the
window after Exit Time expires causes an alarm.
Table 7 defines the different methods for arming the
system.
Table 7: Arming Methods
Indicator
Definition
On
Off
Flashing
There is a system fault you must correct.
The system is normal. There are no faults.
There is a system fault that must be
acknowledged.
3.9
Definition
AWAY Mode
Arms the entire system. Refer to
Section 4.1 Arming in AWAY Mode.
Arms all zones except those
programmed by the installer to be
automatically isolated. Refer to Section
4.2 Arming in STAY Mode 1.
Arms all zones except those
programmed by the Master Code
holder to be automatically isolated.
Refer to Section 4.3 Arming in STAY
Mode 2.
STAY Mode 1
Audible Indications
Table 6 defines the audible indicators generated by
the codepad buzzer.
6
Method
STAY Mode 2
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 4.0
Arming the System
Forced Arming
Arming the system when a zone is not sealed is
known as forced arming. If the system is not armed
and a long beep sounds, forced arming is not
permitted. If this is the case, ensure that all zones are
sealed or manually isolated before arming the
system.
4.1
Arming in AWAY Mode
When you leave your premises and require all zones
to be in a ready state to detect intrusion, arm the
system in AWAY Mode. When returning to your
premises, disarm your system (refer to Section 5.0
Disarming the System) so you do not sound a false
alarm.
There are two different methods for arming the
system in AWAY Mode. One method is standard
and is always available. The other method is optional
and might be disabled by your installer.
To arm in AWAY Mode using the first method:
Enter your user code and press [#] (for example,
[2 5 8 0 #]).
Two beeps sound and the AWAY indicator lights.
Exit Time starts.
To arm in AWAY Mode using the second
method:
Hold down [#] until two beeps sound.
The AWAY indicator lights and Exit Time starts.
4.2
Arming in STAY Mode 1
STAY Mode 1 is only used when the perimeter and
unused areas of the premises must be armed to
detect if an intruder is entering the premises. At the
same time, it allows you to move freely within an
area that is automatically isolated.
Only your security company can
program zones automatically isolated in
STAY Mode 1.
There are two different methods for arming the
system in STAY Mode 1. One method is standard
and is always available. The other method is optional
and might be disabled by your installer.
Entry Guard Timer for STAY Mode 1
When arming the system in STAY Mode 1, an
optional entry timer called Entry Guard Timer for
STAY Mode 1 is available. Use this entry timer to
delay the sirens if a zone is not automatically isolated
and activates an alarm. Entry Guard Timer for STAY
Mode 1 is the delay time used for all zones except
24-hour zones when the system is armed in STAY
Mode 1 or STAY Mode 2.
If the Entry Guard Timer for STAY Mode 1 is
programmed and a zone not automatically isolated is
activated, the codepad beeps twice per sec until the
entry timer expires or the system is disarmed. If the
alarm condition is not reset by entering your user
code and pressing [#] (for example, [2 5 8 0 #])
before the entry timer expires, the sirens sound an
alarm. Only your installer can program this feature.
To arm in STAY Mode 1 using the first method:
Enter your user code and press [*] (for example,
[2 5 8 0 *]).
Two beeps sound and the STAY indicator lights. Exit
Time starts counting.
Any zones programmed to be automatically isolated
in STAY Mode 1 flash until Exit Time expires. At
the end of Exit Time, all zones selected to be
automatically isolated turn off and the codepad gives
one short beep.
To arm in STAY Mode 1 using the second
method:
Hold down [*] until two beeps sound.
The STAY indicator lights and Exit Time starts.
Any zones programmed to be automatically isolated
in STAY Mode 1 flash until Exit Time expires. At
the end of Exit Time, the zone indicators turn off and
the codepad sounds one short beep.
4.3
Arming in STAY Mode 2
STAY Mode 2 is used only when you want to arm
the perimeter and unused areas of the premises to
detect an intruder while you move freely within an
automatically isolated area. Any Master Code user
can program zones to be automatically isolated in
STAY Mode 2.
Entry Guard Timer for STAY Mode 2
When arming the system in STAY Mode 2, an
optional entry timer called Entry Guard Timer for
STAY Mode 2 is available. Use this entry timer to
delay the sirens if a zone is not automatically
isolated, but activates an alarm. Entry Guard Timer
for STAY Mode 2 is the delay time used for all
zones, except 24-hour zones, when the system is
armed in STAY Mode 1 or STAY Mode 2.
If the Entry Guard Timer for STAY Mode 2 is
programmed and a zone not automatically isolated
activates an alarm, the codepad beeps twice a sec
until the entry timer expires or you disarm the
system. If you do not reset the alarm by entering
your user code and pressing [#] (for example,
[2 5 8 0 #]) before the entry timer expires, the system
activates the sirens to sound an alarm. Only your
installer can program this option.
To arm in STAY Mode 2:
Hold down [0] until two beeps sound.
The STAY indicator lights and Exit Time starts.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
7
ICP-CC404 | User's Guide | 5.0
Disarming the System
Any zones programmed to be automatically isolated
in STAY Mode 2 flash until Exit Time expires. At
the end of Exit Time, the indicators turn off for all
zones selected to be automatically isolated and the
codepad sounds one short beep.
4.4
Programming STAY Mode 2 Zones
If you have a Master Code, you can only program
zones to be automatically isolated in STAY Mode 2.
How to Program STAY Mode 2 Zones
1. Enter your four-character Master Code and press
[4 #] key (for example, [2 5 8 0 4 #]).
Three beeps sound and the STAY indicator
flashes.
2. Enter the zone number to automatically isolate
and press [*] (for example, [1 *] for Zone 1 or
[2 *] for Zone 2).
The selected zone flashes.
If you make a mistake, enter the same zone
number and press [#] to clear the incorrect zone.
To select additional zones to automatically
isolate in STAY Mode 2, repeat Step 2 as many
times as necessary.
3. After you select the zones to automatically isolate
in STAY Mode 2, press [#] to exit from this
mode.
Two beeps sound and the STAY and AWAY
indicators turn dark.
5.0 Disarming the System
When you enter the premises after the system is
armed in AWAY Mode, or if you armed the system
in STAY Mode 1 or STAY Mode 2, you must disarm
the system before entry time expires to disable
detection devices that activate an alarm. Only your
installer can program the entry time.
If there was an alarm before you disarm the system,
a flashing zone indicator shows a previous alarm on
that zone.
To disarm the system:
Enter your user code and press [#] key (for example,
[2 5 8 0 #]).
Two beeps sound.
6.0 User Codes
6.1
Adding User Codes
Only the Master Code holder can add or change
other system user codes, including the Master Code.
The Master Code holder can program up to eight
user codes for the system.
8
To add a user code:
1. Enter your four-character Master Code and press
[1 #] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the user code number (1 to 8) and press
[#] (for example, [2 #] for User 2, or [8 #] for
User 8).
Two beeps sound and the selected user number
appears on the codepad indicators.
3. Enter the digits required for the new code and
press [#] (for example, for user code 5768, enter
[5 7 6 8 #]).
Two beeps sound and the STAY and AWAY
indicators turn off.
To add or change other user codes, repeat this
procedure as many times as necessary.
6.2
Adding Radio Remote User Codes
Only the Master Code holder can add or change
other system user codes, including the Master Code.
The Master Code holder can program up to eight
radio user codes (User Codes 9 to 16) for the system.
To add a radio remote user code:
1. Enter your four-character Master Code and press
[1 #] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the radio remote user code number
(9 to 16) and press [#] (for example, [9 #] for
User 9, or [1 6 #] for User 16).
Two beeps sound and the selected user number
appears on the codepad indicators.
3. Press any button on the keyfob so the system
learns the ID number. Two beeps sound and the
STAY and AWAY indicators turn off.
To add or change other radio remote user codes,
repeat this procedure as many times as required.
6.3
Deleting User Codes/Radio User
Codes
Only the Master Code holder can delete other
system user codes.
To delete a user code:
1. Enter your four-character Master Code and press
[1 #] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the user code number (User Code 1 to 8,
or Radio User Code 9 to 16) and press [#] (for
example, [2 #] for User 2, [1 6 #] for User 16).
Two beeps sound and the selected user number
appears on the codepad indicators.
3. Press the [*] key to delete the selected user code.
Two beeps sound and the STAY and AWAY
indicators turn off. To delete other user codes,
repeat this procedure as many times as required.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 7.0
Radio Transmitter Operations
Audible and Visual Indications
7.0
Radio Transmitter
Operations
When using hand-held keyfob transmitters to operate
the system, your security company can program the
keyfobs to sound the horn speaker or operate the
blue strobe light. These indications allow you to
operate the system from outside the premises with
confidence.
Figure 3: RE012/E: 2-Channel Keyfob
Transmitter
1
2
3
1 – Button 1: Arm or disarm in AWAY Mode
2 – Button 2: Arm or disarm STAY Mode
3 – Buttons 1 and 2: Press both buttons at the
same time to activate Panic alarm.
Figure 4: RE013/E: 4-Channel Keyfob
Transmitter
1
3
2
Table 8: Keyfob Audible and Visual Indications
Indication
Definition
One beep
Two beeps
Two-tone beep
3-sec strobe
6-sec strobe
System disarmed.
System armed in AWAY Mode.
System armed in STAY Mode.
System disarmed.
System armed in AWAY or STAY
Mode.
8.0 Alarms
8.1
Duress Alarm
A codepad duress alarm is used as a silent hold-up
alarm. This only occurs when a user adds 9 to the
end of a valid user code when disarming the system
(for example, [2 5 8 0 9 #]). A duress alarm is only
useful if your system reports back to a monitoring
station or pocket pager, because domestic reporting
(such as a mobile phone) cannot decipher which type
of alarm occurred.
Figure 5: ICP-CP508W LED Codepad Showing
Audible Alarm Buttons
4
1 – Button 1: Arm or disarm in AWAY Mode
2 – Button 2: Arm or disarm in STAY Mode
3 – Buttons 1 and 2: Press both buttons at the
same time to activate Panic alarm.
4 – Buttons 3 and 4: Your security company
can program these buttons for optional
operation, such as operating a garage
door.
8.2
Panic Alarm
An audible alarm activates when you press [1] and
[3] or [*] and [#] simultaneously. Contact your
installer to disable the ability to activate the codepad
panic alarm or to silence the codepad panic alarm.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
9
ICP-CC404 | User's Guide | 9.0
8.3
Isolating Zones
Fire Alarm
The horn speaker emits a distinct fire sound when
you press [4] and [6] simultaneously. Contact your
installer to disable the ability to activate the codepad
fire alarm or to silence the codepad fire alarm.
8.4
Medical Alarm
An audible alarm activates when you press [7] and
[9] simultaneously. Contact your installer to disable
the ability to activate the codepad medical alarm or
to silence codepad medical alarm.
8.5
Tamper Alarm (Access Denied)
The tamper alarm restricts the number of times
someone can attempt to use an invalid user code to
operate the system. When the number of incorrect
code attempts equals the number programmed by
your installer, the system activates an alarm. If
reporting back to a security monitoring station, the
system sends an Access Denied Report.
To shut down and lock out a codepad for a period of
time (0 to 150 sec), ask your installer to program this
feature.
9.0 Isolating Zones
Isolating zones allow you to manually disable one or
more zones before arming the system. Once a zone is
isolated, you can access that zone during the armed
state without activating an alarm.
For example, you might need to isolate a zone
because before arming the system a PIR detector
might generate a false alarm, or you need to leave a
pet inside a particular zone while away.
Isolating zones is performed by one of two methods.
The second method is optional and only allows those
user codes programmed by your installer access to
isolate zones.
9.1
Standard Isolating
Standard isolating allows all operators to isolate
zones without knowing a valid user code.
To isolate a zone:
1. Press [*] twice to enter Isolating Mode.
Three beeps sound and the STAY indicator
flashes.
2. Enter the zone number (1 to 8) and press [*] (for
example, [1 *] for Zone 1, or [2 *] for Zone 2).
Each zone to isolate has a corresponding zone
indicator that flashes.
If you selected an incorrect zone to isolate, enter
the incorrect zone number again and press [*].
Repeat Step 2 if you are isolating more than one
zone, until all zones you want to isolate are
selected.
10
3.
9.2
Press [#] after you isolate all selected zones.
Two beeps sound and the system returns to the
disarmed state.
Code to Isolate
Only the user codes with the Code to Isolate priority
level can isolate zones. If any user code has this
priority level, the standard isolating method (refer to
Section 9.1 Standard Isolating) does not function.
To isolate a zone:
1. Press [*], enter your user code, and press [*]
again to enter Isolating Mode (for example,
[* 2 5 8 0 *]).
Three beeps sound and the STAY indicator
flashes.
2. Enter the zone number (1 to 8) and press [*] (for
example, [1 *] for Zone 1 or [2 *] for Zone 2).
Each zone to isolate has a corresponding zone
indicator that flashes. If you selected an incorrect
zone to isolate, enter the incorrect zone number
again and press [*].
If you are isolating more than one zone, repeat
Step 2 until you select the zones you want to
isolate.
3. Press [#] after all selected zones are isolated.
Two beeps sound and the system returns to the
disarmed state.
10.0 Setting the Date and Time
Programming the date and time is only required
when you need functions such as automatic test
reports, automatic arming, and history events to
operate correctly.
To program the date and time:
1. Enter your Master Code and press [6 #] (for
example, [2 5 8 0 6 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the day, month, year, hour, and minute
using the (DD, MM, YY, HH, MM) format (that
is, DD = day of the month, MM = month of the
year, YY = current year, HH = hour of the day,
MM = minute of the day).
When programming the hour of the day,
you must use a 24-hour format.
3.
Press [#] to exit and return to the disarmed state.
Two beeps sound and the STAY and AWAY
indicators turn off. A long beep sounds if you
incorrectly entered the date and time.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 11.0
Fault Analysis Mode
Sensor Watch Fail
11.0 Fault Analysis Mode
If a fault occurs, the FAULT or MAINS indicators
flash and the codepad beeps once every min.
11.1
AC Fail
A sensor watch fault registers because one or more
detection devices failed to notice any movement
during the disarmed state for the time period
programmed by your installer. The fault clears when
the zone in question detects movement and is reset.
If the AC MAINS supply fails, the MAINS indicator
flashes until the AC MAINS supply is restored.
Pressing [#] once acknowledges the fault and stops
the codepad from beeping once every min.
While in Fault Analysis Mode, hold down [5] until
two beeps sound.
The indicator corresponding to the faulted zone
lights.
11.2
Horn Speaker Fail
System Faults
To determine all system faults other than the AC
MAINS supply, enter Fault Analysis Mode:
1. Hold down [5] until two beeps sound.
The FAULT indicator lights steadily and the
STAY and AWAY indicators flash in unison.
Any lit zone indicators indicate the type of fault
that occurred. Refer to Table 9 for the list of
system faults that can occur.
2. To further determine the type of fault condition,
hold down the key that corresponds to the lit
zone indicator.
3. To exit from Fault Analysis Mode and return to
the disarmed state, press [#].
The FAULT indicator remains lit and the
codepad stops beeping once per min.
A horn speaker failure fault registers when the
system detects the horn speaker is disconnected. This
fault clears once the horn speaker is reconnected.
Your installer must program the system for this
feature to operate.
11.3
AUX Power Supply Fail
Fault Descriptions
Table 9: Fault Condition Indicators
Zone LED
1
2
3
4
5
6
7
8
FAULT Condition
Battery Fail
Date/Time
Sensor Watch
Horn Speaker Fail
Telephone Line Fail
EEPROM Fail
AUX Power Supply Fail
Communication Fail
Battery Fail
A battery fail fault registers when the system detects
a low capacity backup battery. The system
automatically performs a Battery Test every 4 hours
and every time the system is armed.
Date and Time
The date and time fault registers every time the
system powers down. This type of fault does not
cause the FAULT indicator to display on the
codepad unless your installer programmed the
automatic arming time. Refer to Section 10.0 Setting
the Date and Time to program the date and time.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
Telephone Line Fail
A telephone line failure fault registers when the
system detects the telephone line is disconnected
from the control panel. Your installer must program
the system for this feature to operate.
EEPROM Fault
An EEPROM failure fault registers when the system
detects an internal checksum error. Contact your
installer if this fault occurs.
An AUX power supply failure fault occurs when
either of the two 1 A AUX power supplies fail.
Contact your installer if this fault occurs.
Communication Fail
A communication fail fault registers when the control
panel fails to communicate with the receiving party
(for example, a monitoring company, mobile phone,
pocket pager, and so on). The communication fault
clears after the control panel successfully reports to
the receiving party.
12.0 Telco Arm/Disarm
Sequence (Call Forward
On/Off)
12.1
Telco Arm Sequence
Use this section to program the Call Forward –
Immediate On sequence or Call Forward – No
Answer sequence to automatically operate when you
arm the system in AWAY Mode. This feature is only
available if your telecommunications provider has
the call-forward option.
The examples given in this feature are
only applicable to Australia.
11
ICP-CC404 | User's Guide | 13.0
Turning Outputs On/Off
2.
Call Forward – Immediate On
You can redirect calls to anywhere in Australia,
including mobile phones, pagers, and answering
services. When Call Forward is turned on, your
telephone does not ring.
3.
Call Forward – No Answer
If your telephone is not answered within 20 sec, this
feature redirects all incoming calls to another number
anywhere in Australia. When this feature is enabled,
you can still make outgoing calls.
To disable the Telco Disarm Sequence,
enter the call forward sequence as [* 4]
(break) for Step 3.
Table 10: Telco Arm/Disarm Dialing Digits
Digit
Required
0
1
2
3
4
5
6
7
Number to
Program
0
1
2
3
4
5
6
7
Digit
Required
8
9
*
#
4-sec pause
break
Number to
Program
8
9
*1
*2
*3
*4
To program the Telco Arm Sequence:
1. Enter your four-character Master Code and press
[3 #] (for example, [2 5 8 0 3 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [1 #] to select the Telco Arm Sequence.
Three beeps sound.
3. Enter the call forward sequence (for example,
[* 6 1][Phone Number][#] to program the Call
Forward - No Answer sequence, or [* 2 1][Phone
Number][#] to program the Call Forward
Immediate sequence).
To program a “*” in the Telco Arm Sequence,
enter [* 1]. To program a “#” in the Telco Arm
Sequence, enter [* 2].
4. Press [#] when finished.
Two beeps sound, and the STAY and AWAY
indicators turn off.
To disable the Telco Arm Sequence,
enter the call forward sequence as [* 4]
(break) for Step 3.
12.2
Telco Disarm Sequence
This feature automatically disables the call forward
sequence when disarming the system.
To program the Telco Disarm Sequence:
1. Enter your four-character Master Code and press
[3 #] (for example, [2 5 8 0 3 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
12
4.
Press [2 #] to select the Telco Disarm Sequence.
Three beeps sound.
Enter the call forward disable sequence (for
example, [# 6 1 #] to disable the No Answer
Call Forward sequence, or [# 2 1 #] to disable
the Call Forward Immediate sequence).
To program a “#” in the Telco Disarm
Sequence, enter [* 2].
Press [#] when finished.
Two beeps sound, and the STAY and AWAY
indicators turn off.
13.0 Turning Outputs On/Off
This feature only applies if your installer set up an
output to be turned on or off by the codepad. Your
installer can program up to three outputs to control a
pool pump, outside lighting, and so on.
To turn an output on or off:
1. Enter your Master Code and press [5 #] (for
example, [2 5 8 0 5 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the output number (1 to 3) you want to
turn on or off.
3. Press [#] to turn the output on, or press [*] to
turn the output off.
Three beeps sound if you turn the output on,
and two beeps sound if you turn the output off.
Repeat Step 2 and Step 3 to turn other outputs on
or off.
4. Press [#] to exit from this function.
Two beeps sound and the STAY and AWAY
indicators turn off.
14.0 Reset Latching Outputs
This feature only applies if your installer
programmed an output to latch (remain on) until you
acknowledge the event that turned on the output.
To reset latching outputs:
Hold down [7] until two beeps sound. The output
resets.
15.0 Codepad ID/Buzzer Tone
Change
Hold down [8] continuously to change the tone of
the codepad buzzer.
There are 50 different tones, from 1500 Hz to
5000 Hz. If multiple codepads are installed, each
codepad can sound a different tone.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 16.0
Testing
To enter Event Memory:
16.0 Testing
There are five functions for testing that your system
operates correctly.
16.1
Horn Speaker Test
Press and hold [1] until two beeps sound.
The horn speaker sounds for 2 sec.
16.2
Bell Test
Press and hold [2] until two beeps sound.
The bell output turns on for 2 sec.
16.3
1.
2.
Strobe Test
Press and hold [3] until three beeps sound.
The strobe flashes.
Press and hold [3] until two beeps sound.
The strobe stops flashing.
16.4
Walk Test Mode
Use Walk Test Mode to test the proper operation of
detection devices. Every time you test a zone, the
codepad sounds one long beep and the horn speaker
sounds one short beep to indicate the zone was
activated when testing.
1. Enter your four-character Master Code and press
[7 #] (for example, [2 5 8 0 7 #]).
Three beeps sound, and the STAY and AWAY
indicators flash. The codepad beeps once per sec
while the system is in Walk Test Mode.
2. Activate the zones you want to test.
The codepad sounds one long beep and the horn
speaker sounds one short beep each time a zone
is faulted (unsealed) and restored.
3. When you finish testing the zones, press [#] to
exit from this mode.
Two beeps sound, and the STAY and AWAY
indicators turn off. The system returns to the
disarmed state.
16.5
Test Report
This feature only applies if your system reports by
telephone. Press and hold [9] until two beeps sound.
The system sends a Test Report without sounding
the sirens.
17.0 Event Memory Recall
Use this function to replay the last 40 system events
that occurred. The event memory history replays all
alarms, and arming and disarming of the system in
AWAY Mode, STAY Mode 1, and STAY Mode 2.
The system cannot differentiate between
arming the system in STAY Mode 1 or
STAY Mode 2.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
Enter your four-character Master Code and press
[8 #] (for example, [2 5 8 0 8 #]).
Three beeps sound. The last 40 events appear one at
a time by the codepad indicators, starting from the
most recent event. A beep sounds as each event
appears.
18.0 Day Alarm
Day alarm allows the system to monitor a
combination of zones when the system is disarmed
by beeping the codepad buzzer. Only your installer
can program Zones 1 to 4 to operate for day alarm.
Example
You can set up a day alarm at the front door of a
shop with a pressure mat or electronic beam that
customers activate as they enter and exit from the
shop. As the customers walk onto the pressure mat
or break the electronic beam, the codepad buzzer
beeps.
To turn day alarm on:
Hold down [4] until three beeps sound.
Day alarm turns on. If a zone programmed for day
alarm operation is activated when the system is
disarmed, the codepad beeps.
To turn day alarm off
Hold down [4] until two beeps sound.
Day alarm turns off.
19.0 Remote Arming By
Telephone
Use this feature to arm your system by telephone
from any remote location. For security reasons, you
cannot disarm the system using this method. This
feature requires a touch-tone telephone. Remote
arming works only if your installer programmed this
feature.
To arm your system remotely by telephone:
1. Call the telephone number connected to your
control panel.
When the control panel answers the incoming
call, a short jingle sounds.
2. To arm the system, press [*] on the touch-tone
telephone for 1 to 3 sec.
If you hear modem tones when the control panel
answers the incoming call, the system is
programmed for remote programming functions
by your installer. Wait for a pause between the
tones before you press [*].
After you release [*] on the touch-tone
telephone, two beeps sound. The system is
armed in AWAY Mode.
13
ICP-CC404 | User's Guide | 20.0
3.
Domestic Dialing
Hang up the telephone.
The system remains armed.
20.2
If your installer programmed answering
machine bypass, you must call the control
panel twice to connect to the system. For
example, call the telephone number for
the control panel, let the call ring no more
than four times, and then hang up the
telephone. Wait at least 8 sec and call the
control panel again.
20.0 Domestic Dialing
Domestic dialing enables the control panel to call
your mobile phone or a relative or friend if the
system detects an alarm. You can program up to
three different telephone numbers to call when an
alarm occurs. Although only your installer can set
the system to report in the domestic format, the
Master Code holder can change the domestic
telephone numbers at any time.
20.1
Acknowledging Domestic Calls
If an alarm occurs, the system calls the first
programmed telephone number. When you answer
an incoming call, the system sounds a repeating siren
tone followed by a pause, continuously for 2 min (for
example, siren tone, pause, siren tone, and pause).
If you do not acknowledge the call from the control
panel during a pause between siren tones, the control
panel hangs up after 2 min, and calls the next
telephone number.
Press [*] for 1 to 3 sec during the pause to
acknowledge the call.
If you acknowledge the call, the control panel does
not call any more phone numbers for that event. If
the call is successfully acknowledged, a tone of
decreasing pitch sounds.
Table 11: Domestic Dialing Telephone Digits
Digit
Required
0
1
2
3
4
5
6
7
14
Number to
Program
0
1
2
3
4
5
6
7
Digit
Required
8
9
*
#
4-sec pause
break
Number to
Program
8
9
*1
*2
*3
*4
Programming Domestic Telephone
Numbers
If your system is configured for domestic dialing, the
Master Code holder can program the telephone
numbers the control panel calls if an alarm occurs.
To program telephone numbers:
1. Enter your four-character Master Code and press
[2 #] (for example, [2 5 8 0 2 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
If there are telephone numbers already
programmed, the numbers appear one digit at a
time by the codepad indicators.
If there are no telephone numbers programmed,
another two beeps sound after entering this
mode. These two beeps are normally heard after
the last digit of the last telephone number
appears.
2. Enter the first telephone number (for example,
[9 6 7 2 1 7 1 7]).
As you enter each digit, the corresponding
codepad indicators light.
3. To program another telephone number, press
[* 4] and repeat Step 2.
This inserts a break between the first telephone
number and the second telephone number.
4. Press [#] to exit from this function.
20.3
Disable Domestic Dialing
To suspend domestic dialing (for example, you are
moving and do not want the system to continue
calling your mobile phone):
1. Enter your four-character Master Code and press
[2 #] (for example, [2 5 8 0 2 #]).
Two beeps sound and the STAY and AWAY
indicators flash.
2. Press [* 4 #].
The STAY and AWAY indicators turn off.
21.0 Basic Pager Reporting
This feature only applies if your system reports to a
pocket pager. Basic pager reporting requires some
interpretation of the numbers that appear on the
display. It is possible to differentiate between 1000
different systems when a number of control panels
report to the one pocket pager.
Subscriber ID Number
This is the identification number of the control panel.
Only your installer can program this number.
Zone Status
The zone status display shows the status of each zone
(1 to 8). Table 12 describes each number of the zone
status display.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 21.0
Basic Pager Reporting
Table 12: Zone Status Display Descriptions
Display
0
1
2
3
Zone Description
Normal. The corresponding zone is sealed.
Alarm. The corresponding zone is unsealed
and in alarm.
Bypassed. A system operator manually
isolated the corresponding zone. Refer to
Section 9.0 Isolating Zones for information
about manually isolating a zone(s) before
arming the system.
Trouble. A zone was unsealed when Exit Time
expired.
System Status
The system status information is divided into the four
digits identified in Table 13.
Table 13: System Status
Digit
Description
First
8 = the system is disarmed
9 = the system is armed
Identifies the codepad alarm activated by the
operator:
0 = No Codepad Alarm
1 = Codepad Panic or Duress Alarm
2 = Codepad Fire Alarm
3 = Codepad Medical Alarm
0 = AC Supply is normal
1 = AC Supply failed
0 = System Normal – There are no faults.
1 = System Fault – The control panel
registered a fault.
Second
Third
Fourth
Figure 6 on page 16 shows a transmission from a
control panel with an ID number of 678, and Zone 2
in alarm. Figure 6 on page 16 also shows Zone 3 is
manually isolated and the system is armed.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
15
ICP-CC404 | User's Guide | 21.0
Basic Pager Reporting
Figure 6: Basic Pager Display
1–
2–
3–
4–
Subscriber ID number
Zone status
System status
0: Zone Normal
1: Alarm
2: Manually Isolated
5 – 8: Disarmed
9: Armed
16
6 – 0: Normal
1: Panic/Duress
2: Fire Alarm
3: Medical Alarm
7 – 0: AC Normal
1: AC Failure
8 – 0: System Normal
1: System Fault
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 22.0
Glossary of Terms
22.0 Glossary of Terms
Table 14: Glossary of Terms
Term
24-hour zone
alarm condition
answering machine
bypass
Armed (System ON)
automatic arming
automatic disarming
AWAY Mode
codepad
day alarm
detector
disarmed
dynamic battery
testing
entry delay
external equipment
force arming
hand-over delay
hand-held radio
remote control
isolate
master code
monitoring station
panic
sealed
Description
A monitored input where tamper switches and emergency switches can be
connected. If one of these switches is violated at any time (whether the system is
armed or disarmed), an alarm is reported.
The status when an alarm system is armed and one of the detection devices is
violated. A 24-Hour zone (for example, a smoke detector) can activate when the
system is armed or disarmed.
A condition that enables connection with the control panel for remote arming or
remote programming operations when there is an answering machine or facsimile
machine on the same telephone line.
A status in which the system is ready to accept alarms.
Programming that allows the system to arm automatically at the same time each day
in AWAY Mode or STAY Mode 1.
Programming that allows the system to disarm automatically at the same time each
day in AWAY Mode or STAY Mode 1.
The mode used to arm your system when you leave your premises.
A device that allows you to perform all functions such as arming, disarming, and
programming of your alarm system.
Programming that allows a combination of zones to be monitored while the system
is disarmed.
A unit installed as a satellite component in a security system designed to detect an
intruder within a protected area. Some common forms of detection devices are
passive infrared, smoke, photo electric beams, reed switches, and vibration sensors.
A system status that does not accept alarms, except for 24-hour zones.
A method used to monitor and test the condition of your backup battery.
A programmed delay of the system alarm responses that allows a person to enter a
building through the entry door to turn the system off.
Any device connected to a security system, such as a detector, codepad, or siren.
A method of overriding the safety feature that prevents arming with a faulted zone
on a control panel.
If a system is armed and Zone 1 is violated, the entry delay starts timing. If Zone 2 is
violated, the entry delay time is handed over to the Zone 2 and so on, to Zones 3
and 4. This is known as sequential hand-over delay.
A device used to arm and disarm a security system or to cause a panic alarm.
A method of manually disabling (isolating) one or more zones before arming the
system.
A numeric code used for arming and disarming the system, and for allowing access
to all functions available through the codepad.
A secure location where a digital receiver monitors a number of alarm systems and
deciphers their alarm transmission reports so the operator can advise the
appropriate authorities to take immediate action.
A condition or type of alarm in which the user requires either immediate police or
medical assistance.
Refers to a zone’s status. If a zone is sealed, the detection devices are not violated
and the zone indicator is not lit (that is, a reed switch is closed or a detector is on
standby waiting for an intrusion).
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
17
ICP-CC404 | User's Guide | 22.0
Glossary of Terms
Table 14: continued
Term
sensor watch
silent alarm
STAY Mode 1
STAY Mode 2
telco arming
sequence
telco disarming
sequence
unsealed
user code
zone
18
Description
A feature that allows the control panel to recognize when detection devices might
have stopped working. Sensor watch monitors the operation of a zone over a
programmed time period.
An alarm that sounds only at a remote location, and gives no obvious local
indication that an alarm was sent out.
A condition that automatically isolates certain zones when the security system is
armed in this mode. Only the installer can program these zones.
A condition that automatically isolates certain zones when the security system is
armed in this mode. The Master Code holder can program these zones.
A feature that automatically diverts a telephone number to another telephone when
a security system is armed in AWAY Mode, the same as using call forwarding.
An automatic suspension of diverting of the telephone when the system is disarmed.
Refers to a zone’s status. If a zone is unsealed, the detection devices are violated
and the zone indicator is lit (that is, a reed switch is open or a detector noted an
intrusion).
A numeric code used to arm and disarm the system.
A monitored input used to activate an alarm. A zone might be set up to activate an
alarm only when the system is armed or to operate whether the system is armed or
disarmed.
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 23.0
Installation Notes
23.0 Installation Notes
Company Name
Technician’s Name
Technician’s Telephone Number
Installation Date
Warranty Expires
Panel Software Version
Service Notes
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
19
ICP-CC404 | User's Guide | 23.0
Installation Notes
Zone Description
Describe each zone and mark the zones that are programmed to be automatically isolated in STAY Mode 1
or are programmed for day alarm operation.
Isolated In
STAY Mode 1
Day Alarm
Enabled
Zone 1
Zone 2
Zone 3
Zone 4
User Code Names
Master
Code
Default = 2580
20
User Code 1
Y
User Code 9
User Code 2
User Code 10
User Code 3
User Code 11
User Code 4
User Code 12
User Code 5
User Code 13
User Code 6
User Code 14
User Code 7
User Code 15
User Code 8
User Code 16
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 23.0
Installation Notes
Entry/Exit Times
Entry Timer 1
Exit Time
Entry Timer 2
Entry Guard Time
Arming Options
Single Button Arming
YES
NO
Forced Arming
YES
NO
Single Button Disarming
YES
NO
Remote Arming By Telephone
YES
NO
Automatic Arming (AWAY Mode)
YES
NO
Automatic Arming Time
AM/PM
Automatic Arming (STAY Mode)
YES
NO
Automatic Disarming Time
AM/PM
Output Descriptions
Output 1
Output 3
Output 2
Output 4
Isolating Method
Standard Isolating
YES
NO
Code To Isolate
YES
NO
Communication Options
Back To Base Reporting
YES
NO
Domestic Reporting
YES
NO
Domestic Reporting – Number Of Beeps
Other System Information
Siren Run Time
Minutes
Sensor Watch Time
Increments in Days
Can Your System Be Serviced By Another Technician
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
YES
NO
If Yes, Installer’s Code
21
ICP-CC404 | User's Guide | 24.0
Specifications
24.0 Specifications
Table 15: Specifications
Temperature Range
Humidity
Power Source
Standby Current
Current Draw In Alarm
Current Draw In Alarm
with Codepad
Backup Battery
Dimensions (case,
packed in carton)
Weight
Supplier Code
New Zealand
Telepermit
-10oC to +45 oC
o
o
(+14 F to +113 F)
10% to 95%
TF008 Plug Pack –
240 VAC/18 VAC @ 1.3 A
65 mA
115 mA
105 mA
6 Ah/12 VDC Rechargeable
sealed lead acid battery
30.6 cm x 26.2 cm x 8.4 cm
(12.1 in. x 10.3 in. x 3.3 in.)
2.5 kg (5.5 lb)
N771
PTC 211/98/085
The ICP-CC488 Control Panel is
designed to comply with A-Tick.
Test the sirens, strobe, and zones at
weekly intervals. Refer to Section 16.0
Testing on page 13 for further
information.
22
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
ICP-CC404 | User's Guide | 24.0
Specifications
Index
24-Hour Zones
AC Mains Fail
Alarm Condition
Alarms
Duress
Fire
Medical
Panic
Tamper (Access Denied)
Answering Machine Bypass
Armed
Arming
AWAY Mode
STAY Mode 1
STAY Mode 2
Telephone Arming
Audible Indications
Automatic Arming
Automatic Disarming
AUX Power Supply Fail
AWAY Indicator
AWAY Mode
Battery Fail
Battery Testing
Bell Test
Codepad
Duress Alarm
Fire Alarm
Medical Alarm
Panic Alarm
Tamper Alarm
Codepad Indicators
Audible Indications
AWAY Indicator
FAULT Indicator
MAINS Indicator
Off Indicator
On Indicator
STAY Indicator
System Disarmed
Zone Indicators
Communciation Fail
Date and Time
Day Alarm
Detectors
Disarmed
Disarming
Domestic Dialing
Acknowledging Domestic Calls
Disable
Programming Domestic Telephone Numbers
Duress Alarm
EEPROM Fault
Entry Delay/Entry Time
Entry Guard Timer
Event Memory Recall
External Equipment
Fault Analysis
Fault Description
AC Mains Fail
AUX Power Supply Fail
20
14
20
11
12
12
12
12
20
20
8
8
8
17
7
20
20
14
6
8, 20
14
20
16
20
11
12
12
12
12
7
6
7
7
7
7
6
6
5
14
14
17
20
20
9
17
18
18
11
14
20
8, 9
16
20
14
14
14
Bosch Security Systems, Inc. | 12/08 | F01U089400-02
Battery Fail
Date and Time
EEPROM Fault
Horn Speaker Fail
Sensor Watch Fail
Telephone Line Fail
Fault Descriptions
Communciation Fail
System Fault
FAULT Indicator
Features
Fire Alarm
Forced Arming
Hand Held Remote Control
Handover Delay
Horn Speaker Fail
Horn Speaker Test
Isolating
Isolating Zones
Code to Isolate
Standard Isolating
MAINS Indicator
Master Code
Medical Alarm
Monitoring Station
Off Indicator
On Indicator
Pager Reporting
Panic Alarm
Radio User Codes
Remote Arming
Remote Control
Sealed
Sensor Watch
Sensor Watch Fail
Silent Alarm
STAY Indicator
STAY Mode 1
Entry Guard Timer
STAY Mode 2
Entry Guard Timer
Programming Zones
Strobe Test
System Disarmed
Tamper Alarm
Telco Arm Sequence
Telco Disarm Sequence
Telephone Line Fail
Test Report
Testing
Bell Test
Horn Speaker Test
Strobe Test
Test Report
Walk Test
Unsealed
User Codes
Radio Users
Walk Test
Zone Indicators
Zones
14
14
14
14
14
14
14
14
14
7
4
12
8, 20
20
20
14
16
20
12
12
12
7
20
12
20
7
7
18
12, 20
9, 10
17
20
20
20
14
22
6
8, 22
8
8, 22
9
9
16
6
12
15, 22
22
14
16
16
16
16
16
16
22
9, 10, 22
9
16
5
22
23
© 2008 Bosch Security Systems, Inc.
F01U089400-02