Sharp 27N-S300 Service manual

27N-S300
CN27S30
SERVICE MANUAL
SERVICE MANUAL
S20X227N-S300
COLOR TELEVISION
Chassis No. SN-81A
PI P
/MT
S
COLOR TELEVISION
MODELS
27N-S300
CN27S30
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................ 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 6
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 7
» CHASSIS LAYOUT ............................................................................................................................. 13
» BLOCK DIAGRAM ............................................................................................................................. 14
» SCHEMATIC DIAGRAMS ................................................................................................................... 15
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 23
» REPLACEMENT PARTS LIST............................................................................................................ 27
» PACKING OF THE SET ..................................................................................................................... 36
MODELS 27N-S300/CN27S30
ELECTRICAL SPECIFICATIONS
SPEAKER
POWER INPUT ................................................... 120 V AC 60 Hz
SIZE ...................................................................... 8 cm (Round)
POWER RATING ................................................................... 126W
VOICE COIL IMPEDANCE ............................... 8 ohm at 400 Hz
2
PICTURE SIZE ......................................... 2,187 cm (339 sq inch)
ANTENNA INPUT IMPEDANCE
CONVERGENCE ............................................................. Magnetic
VHF/UHF .................................................... 75 ohm Unbalanced
SWEEP DEFLECTION ..................................................... Magnetic
TUNING RANGES
FOCUS ............................................... Hi-Bi-Potential Electrostatic
VHF-Channels .............................................................. 2 thru 13
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
UHF-Channels ............................................................ 14 thru 69
Sound IF Carrier Frequency ...................................... 41.25 MHz
CATV Channels .......................................................... 1 thru 125
Color Sub-Carrier Frequency ..................................... 42.17 MHz
(EIA, Channel Plan U.S.A.)
(Nominal)
AUDIO POWER
OUTPUT RATING .............. 1.3W + 1.3W (at 10% distortion and
Dual CH Operate)
SHARP CORPORATION
Specifications are subject to change without
prior notice.
1
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
27N-S300
CN27S30
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are throughly
familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation.
The only potential source of X-ray in current solid
state TV receivers is the picture tube. However, the
picture tube does not emit measurable X-Ray
radiation, if the high voltage is as specified in the
"High Voltage Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
-no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem.
Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
4A 125V
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
27N-S300
CN27S30
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon and etc.) and measure the AC voltage
drop across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators and etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
AC
VOLTMETER
1.5k ohm
10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
SAFETY NOTICE
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the
same safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement
components rated for higher voltage, wattage andetc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
3
27N-S300
CN27S30
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé
à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur possède deux systèmes
de masse qui sont séparées par du matériel
d'isolation. Le système de masse non-isolée (sous
tension) est pour le circuit du régulateur de tension
B+ et le circuit de sortie horizontale. Le système de
masse isolée est pour les tensions DC B+ basses et
le circuit secondaire du transformateur haute tension.
Pour éviter tout risque d'électrocution lors de
l'entretien de ce châssis, utiliser un transformateur
d'isolation entre le cordon de ligne et la prise de
courant.
4A 125V
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesurables si la haute tension est maintenue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est excessive
que les rayons X peuvent entrer dans l'enveloppe
du tube-image y compris le conducteur de verre. Il
est important de maintenir la haute tension endessous du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
voltmètre à haute tension qui doit être
périodiquement étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime -et pas plus haute. L'opération à
des tensions plus élevées peut entraîner une panne
du tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation
X. Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive, éviter de s'approcher inutilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
PRECAUTION: POUR LA
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V.
REPARATION DU SYSTEME A HAUTE
TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 kΩ en série avec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le corden d'alimentation doit être
retiré de la prise murale.)
1. Le tube image dans ce récepteur emploie une
protection intégrée contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
4
27N-S300
CN27S30
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
• Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance. Toutes les vérifications doivent être
refaites après avoir inversé la fiche du cordon
d'alimentation. (Si nécessaire, une prise d'adpatation
non polarisée peut être utilisée dans le but de
terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne
soit pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
• Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
• A l'aide de deux fils à pinces, brancher une résistance
de 1,5 kW 10 watts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
• Utiliser un voltmètre CA d'une sensibilité d'au moins
5000W/V pour mesurer la chute de tension en travers
de la résistance.
Voltmètre CA
1.5k ohm
10W
0.15µF
SONDE D'ESSAI
AUX PIECES
METALLIQUES
TOEXPOSEES
EXPOSED
METAL PARTS
BRANCHER A UNE
TERRE
CONNUE
CONNECT
TO
KNOWN EARTH
GROUND
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
AVIS POUR LA SECURITE
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
5
27N-S300
CN27S30
LOCATION OF USER'S CONTROL
Front Panel
A
POWER
Press → On.
Press again → Off.
B
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
POWER
POWER
C
SENSOR AREA FOR REMOTE CONTROL
D
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
• Press both at the same time to access the MAIN Menu
screen.
E
– VOL +
CH
A
E
– VOL +
CH
B
D
C
VIDEO/AUDIO IN 2 TERMINALS
(VIDEO/AUDIO terminals are also
provided on the rear.)
Basic Remote Control Functions
Infrared Transmitter Window
POWER
Press → On.
Press again → Off.
DISPLAY
Press → Displays receiving channel for
4 seconds.
Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
POWER
TV
VCR
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
PERSONAL PREFERENCE
With the Personal Preference buttons,
you can program your favorite
programs by using the 4 categories A,
B, C and D. The channels can be
accessed quickly by using these
buttons.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
TV-CATV MODE SELECT SWITCH
In TV position, sends power and
channel select commands (Channel
up/down and Random Access buttons)
to the TV.
In CATV position, sends power and
channel select commands to a cable
TV converter.
DISPLAY
INPUT
1
2
3
4
5
6
7
8
9
FLASHBACK
INPUT
Press → Switch to external video
INPUT 1 mode.
Press again → Switch to external video
INPUT 2 mode.
Press 3 times → Switch back to the
original TV mode.
ENTER
0
100
PERSONAL PREFERENCE
A
B
C
D
CH
VOL
—
VOL
+
CH
MENU
MUTE
CATV
REW
PLAY
FF
PAUSE
STOP
REC
VCR CH
FREEZE
MOVE
SELECT
PIP
SWAP
TV
ENTER
Used in some instances where a VCR
or Cable Converter Box requires an
“enter” command after selecting
channels, when using the REMOTE
KEYPAD button.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
” mark of the MENU
• Moves the “
screens.
TV • VCR • CATV
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
VCR CONTROL
PIP FUNCTION
With the VIDEO inputs, you can watch
two pictures at the same time.
Note:
• The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
• Sunlight and fluorescent lighting are the most effective when charging the display.
6
27N-S300
CN27S30
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 4.0A fuse
(F701), mounted on PWB-A, wired into one
side of the AC line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly
tuned in test signal.
3. Enter the service mode and select the service
adjustment "S19" and Bus data "01" (Y-mute on).
4. The voltage should be approximately, 28.1kV (at zero
beam).
If a correct reading cannot be obtained, check
circuitry for malfunctioning components. After the
voltage test, make Y-mute off to the normal mode.
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 11.4 ± 0.7V.
5. Apply external 13.8V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before
the set is returned to the customer.
7
27N-S300
CN27S30
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required.
1. Service mode
To enter the service mode and exit service mode.
Before putting unit into the service mode, check that
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to
ensure customer controls are in their proper (reset)
position.
While pressing the Vol-up and Ch-up buttons at the
same time, plug the AC cord into a wall socket.
Now the TV set is switched on and enters the service
mode.
To exit the service mode, turn the television off by
pressing the power button.
2. Service number selection
Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set.
The ser vice adjustment number will var y in
increments of one, from "S01" to "P07". Select the
item you wish to adjust.
3. Data number selection
Press the Vol-up or down button to adjust the data
number.
DATA NUMBER
CHANNEL
SERVICE ADJUSTMENT NUMBER
S01
55(085)
02
S01 D:00
Figure A.
8
27N-S300
CN27S30
SERVICE
NUMBER
S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
OP1
OP2
M01
M02
M03
M04
M05
P01
P02
P03
P04
P05
P06
P07
DATA
ADJUSTMENT ITEM
INITIAL VALUE
PICTURE
TINT
COLOR
BRIGHTNESS
SHARPNESS
VERTICAL PHASE
HORIZONTAL PHASE
RF-AGC
VERTICAL AMP
PIF VCO
R CUT-OFF
G CUT -OFF
B CUT-OFF
G GAIN
B GAIN
TRAP
55
46
32
40
28
00
12
23
20
2C
00
00
00
7F
7F
00
20
17
00
20
7A
00
00
00
00
0A
20
1C
20
1B
30
29
2E
09
0A
00
0B
C.C.POSITION
MUTE
ENERGY SAVE OFFSET
TIMER
TUNER SETUP
OPTION1
OPTION2
INPUT LEVEL
ST VCO
FILTER
WIDE BAND
SPECTRAL
P in P Y-LEVEL
P in P TINT
P in P COLOR
P in P Y-OFFSET
P in P H-POSITION
P in P BURST GATE PULSE
P in P FREE RUN
ADJUSTMENT CONTENTS
RANGE
00-7F
00-7F
00-7F
00-7F
00-3F
00-07
00-1F
00-3F
00-3F
00-7F
00-FF
00-FF
00-FF
00-FF
00-FF
00 or 01
00-3F
00-FF
00,01,03
00-3F
00-FF
00
00, 01
00-FF
00-FF
00-0F
00-3F
00-3F
00-3F
00-3F
00-7F
00-3F
00-7F
00-1F
00-FF
00-7F
00-0F
Must be set to "24"
Must be set to "00"
Must be set to "01"
Must be set to "20"
"00"=Normal, "01"=No Y, "03"=No Vertical & No Y
Must be set to "23"
Must be set to "7A"
Must be set to "00"
Must be set to "00"
Must be set to "B7"
Must be set to "A7"
Must be set to "29"
Must be set to "09"
Must be set to "0A"
Must be set to "00"
Must be set to "0B"
Table - A
Holding down both the Vol-up/CH-down buttons on the TV set at service mode for more than 2 seconds will
automatically write the above initial values into IC2101.
ADJUSTMENT
PART REPLACED
NECESSARY
NOTES
UNNECESSARY
X
IC2001
Data is stored in IC2101.
X
The adjustment is needed to compensate for characteristics
of parts including IC201 and MTS level (M01).
IC2101
X
Holding down both the Vol-up/CH-down buttons on the TV
set in the service mode for more than 2 seconds will
automatically write the above initial values into IC2101. Then
perform a complete adjustment.
CRT
X
Adjust items related to picture tube only.
IC3001
X
Adjust items related to MTS only (M01~M05).
IC1801
X
Adjust items related to P-IN-P only (P01~P07).
IC201
Table - B
9
27N-S300
CN27S30
SERVICE ADJUSTMENT
VCO Adjustment
White Balance Adjustment
1. Connect a digital voltmeter between pin (44) of IC201
and ground.
2. Receive a good local channel.
3. Enter the service mode and select the service
adjustment "S10".
4. Adjust the data so that digital voltmeter reads 2.2V.
5. Adjustment is completed, remove the voltmeter,
return to "normal" mode.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S03" and set to "00" (minimum
color)(Record original data code under adjustment
"S03" before changing). "S03" does not have to be
adjusted, if you selected a B/W picture or monoscope
pattern.
3. Alternately adjust the service adjustment data of
"S14" and "S15" until a good grey scale with normal
whites is obtained.
4. Select the service adjustment "S03" and adjust data
to obtain normal color level.
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S08".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
Note 1: You will have to come out of the service
mode to select another channel.
Note 2: Setting the data to "00" will produce a black
raster.
Sub-Picture Adjustment
1. Receive a good local channel.
2. Make sure the customer picture control is set to
maximum.
3. Enter the service mode and select the service
adjustment "S01".
4. Adjust the data value to achieve normal contrast
range.
Screen Adjustment
Sub-Tint Adjustment
1. Connect a digital voltmeter between TP852 and
TP853 on the CRT Unit.
Note: These test points may not be provided.
Then connect the voltmeter to both ends of
R852 located near Q851 on the foil side.
2. Receive a good local channel.
3. Enter the service mode and select the service
adjustment "S03" and set the data value to "00" to
set the color level to minimum. (Record original data
code under adjustment "S03" before changing) You
may skip this step, if you selected a B/W picture or
monoscope pattern.
4. Select the service adjustment "S19" and adjust the
data value to "01", this turn off the luminance signal
(Y-mute).
5. Select the service adjustment "S04" and adjust data
value to obtain 0.26 volts on the digital voltmeter.
6. Adjust the master screen control until the raster
darkens to the point where raster is barely seen.
7. Adjust the service adjustments "S11" red, "S12"
green and "S13" blue to obtain a good grey scale
with normal whites at low brightness level.
8. Select the service adjustment "S19" and reset data
to "00". Select the service adjustment "S03" and reset
data to obtain normal color level.
9. Remove digital voltmeter, and reset the master
screen control to obtain normal brightness range.
1. Receive a good local channel.
2. Set customer tint control to center of it's range.
3. Enter the service mode and select the service
adjustment "S02".
4. Adjust "S02" data value to obtain normal flesh tones.
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position .
3. Enter the ser vice mode and select ser vice
adjustment "S03".
4. Adjust "S03" data value to obtain normal color level.
10
27N-S300
CN27S30
Sub-Brightness Adjustment
3.58MHz Trap Adjustment
1. Receive a good local channel.
2. Make sure the customer brightness control is set to
center position.
3. Enter the service mode and select the service
adjustment "S04".
4. Adjust "S04" data value to obtain normal brightness
level.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S16".
3. This is a two position adjustment, "00" is ON, "01" is
OFF.
4. Adjust data value to "01" for normal viewing.
Sharpness Adjustment
Vertical-Size Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustments "S05" for sharpness and "S17" for
balance.
» Sharpness Adjustment
3. Adjust data value to "24"(center of data range) for
sharpness adjustment.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S09".
3. While observing the top and bottom of the screen,
adjust "S09" data value to proper vertical size.
Vertical Phase Adjustment
Energy save offset Adjustment
1. Enter the service mode and select the service
adjustment "S06".
2. Adjust data value to "00".
Note: This must be set "00" when changed data retrace
line will appear.
1. Enter the service mode and select the service
adjustment "S20".
2. Adjust data value to "23".
Note: This position is used to preset the level for the
energy save function.
Horizontal Position Adjustment
Other Adjustments
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S07".
3. Adjust "S07" data value so that picture is centered.
1. Enter the service mode.
2. Adjust the following data values as listed below.
SERVICE
POSITION
S05
S06
S16
S20
S21
S23
OP1
OP2
Caption Position Adjustment (Horizontal)
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S18".
3. A black text box appears on the screen. (see Figure
B. below)
4. Adjust "S18" data value so that text box is positioned
in the center of the screen.
Figure B.
11
ADJUST
ITEM
SHARPNESS
V-PHASE
TRAP
E-SAVE
TIMER
TUNER SETUP
OPTION1
OPTION2
DATA
(Hex)
24
00
01
23
7A
00
B7
A7
27N-S300
CN27S30
MTS ADJUSTMENT
P-IN-P ADJUSTMENT
MTS Level Adjustment
P-IN-P Y LEVEL Adjustment
1. Feed the following monaural signal to pin (14) of
IC3001.
Monaural signal : 300Hz, 245mVrms
2. Connect the rms voltmeter to pin (39) of IC3001.
3. Enter the service mode and select the service
adjustment "M01".
4. Adjust the data so that the rms voltmeter reads 490
± 10mVrms.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "P01".
3. Adjust "P01" data value to obtain normal contrast
level.
P-IN-P TINT Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "P02".
3. Adjust data value to "29".
MTS VCO Adjustment
1. Keep the unit in no-signal state.
2. Connect the frequency counter to pin (39) of IC3001.
3. Connect a capacitor (100µF, 50V) in between
positive(+) side of C3005 and ground.
4. Enter the service mode and select the service
adjustment "M02"
5. Adjust the data so that the frequency counter reads
62.94 ± 0.75kHz.
P-IN-P COLOR Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position.
3. Enter the service mode and select the service
adjustment "P03".
4. Adjust "P03" data value to obtain normal color level.
Filter Adjustment
P-IN-P Y-OFF SET Adjustment
1. Feed the following stereo pilot signal to pin (14) of
IC3001 .
Stereo pilot signal: 9.4kHz, 600mVrms.
2. Enter the service mode and select the service
adjustment "M03".
3. Adjust the data at the point where "OK" appears on
the screen. The "OK" represents the approximate
center of the adjustable range of the data.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "P04".
3. Adjust data value to "09".
P-IN-P H-POSITION Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "P05".
3. Adjust data value to "0A".
Separation Adjustment
1. Connect the rms voltmeter to pin (39) of IC3001.
2. Receive the following composite stereo signal 1.
Composite stereo signal: 30% modulation, left
channel only, noise reduction on, 300Hz
3. Enter the service mode and select the service
adjustment "M04".
4. Adjust the data until the AC voltage reading of the
rms voltmeter is minimum.
5. Receive the following composite stereo signal 2.
Stereo signal: 30% modulation, left channel only,
noise reduction on, 3kHz
6. Enter the service mode and select the service
adjustment "M05".
7. Adjust the data until the AC voltage reading of the
rms voltmeter is minimum.
8. Take the above steps 1 thru 7 again for fine
adjustment.
P-IN-P BURST GATE PULSE (for MAIN)
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "P06".
3. Adjust data value to "00".
P-IN-P TREE RUN
1. Recieve a good local channel.
2. Enter the service mode and select the service
adjustment "P07".
3. Adjust data value to "0B".
12
27N-S300
CN27S30
CHASSIS LAYOUT
PWB-H
PWB-R
PWB-B
H
G
PWB-A
F
E
D
C
B
A
10
1
11
122
13
3
14
15 4
13
16
5 17
18
6
19
27N-S300
CN27S30
BLOCK DIAGRAM
HH
GG
FF
EE
DD
CC
BB
AA
1
1
2
32
4
3
5
6 4
14
7
5 8
9
6
10
27N-S300
CN27S30
DESCRIPTION OF SCHEMATIC DIAGRAM
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
3. (G) indicates ±2% tolerance may be used.
4.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
åAND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
' MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES å ET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE ' : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
WAVEFORMS
10
11
12
13
14
15
15
16
17
18
19
27N-S300
CN27S30
27N-S300
CN27S30
SCHEMATIC DIAGRAM: MAIN-1 Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
16~17
12
13
14
15
16
17
18
19
20
27N-S300
CN27S30
27N-S300
CN27S30
SCHEMATIC DIAGRAM: MAIN-2 Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
18~19
12
13
14
15
16
17
18
19
20
27N-S300
CN27S30
27N-S300
CN27S30
SCHEMATIC DIAGRAM: P-IN-P Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
20~21
12
13
14
15
16
17
18
19
20
27N-S300
CN27S30
SCHEMATIC DIAGRAM: CRT and FRONT AV Units
HH
GG
FF
EE
DD
CC
BB
AA
1
1
2
32
4
3
6 4
5
22
7
5 8
9
6
10
27N-S300
CN27S30
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
PWB-B: CRT Unit (Wiring Side)
D
C
B
PWB-H: FRONT AV Unit (Wiring Side)
A
10
1
11
122
13
3
15 4
14
23
16
5 17
18
6
19
27N-S300
CN27S30
HH
GG
FF
EE
DD
CC
BB
PWB-A: MAIN Unit (Wiring Side)
AA
1
1
2
32
4
3
6 4
5
24
7
5 8
9
6
10
27N-S300
CN27S30
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Chip Parts Side)
A
10
1
11
122
13
3
15 4
14
25
16
5 17
18
6
19
27N-S300
CN27S30
HH
GG
FF
EE
PWB-R : P-IN-P Unit (Wiring Side)
DD
CC
BB
PWB-R : P-IN-P Unit (Chip Parts Side)
AA
1
1
2
32
4
3
6 4
5
26
7
5 8
9
6
10
27N-S300
CN27S30
Ref. No.
Part No.
★
Description
Code
Ref. No.
★
Part No.
Description
Code
LISTE DES PIECES
PARTS LIST
PARTS REPLACEMENT
CHANGE DES PIECES
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques
sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les
pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep
éler élee par la marque å et sont hachur élees dans les listes de
pi`eces et dans les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr
éLesente pas les m éoemes caract éLeristiques de s élecurit éle que
la pi`ece recommand élee parl'usine et dans ce manuel de service,
peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
in USA:
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP
2. NO. DE REF
3. NO. DE PIECE
4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Conada Limited
Phone (416) 890-2100
★ MARK: SPARE PARTS-DELIVERY SECTION
★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
▲ MARK: X- RAY RELATED PARTS
▲ MARQUE: PIECES RELATIVE AUX RAYONS X
Ref. No.
Part No.
★
Description
Code
Ref. No.
V101
L702
VB68ADT2506*S
RCiLG0038MEZZ
M Picture Tube (I.T.C.)
M Degaussing Coil
(PR701:P0092CE)
MSPRT0002MEZZ M Spring for CRT
QEARC2702MEZZ M Grounding Part
★
Part No.
Description
Code
PWB-A: DUNTKA120WEK0/1
PICTURE TUBE
çå
å
1. NUMERO DU MODELE
MAIN UNIT
TUNER
CP
AP
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED
AS AN ASSEMBLY BUT NOT INDEPENEDENTLY.
å TU51 VTUVTST5UF78S J Tuner
BD
or
VTU115B8035AH
AA
AD
INTEGRATED CIRCUITS
IC101
çå IC201
IC351
IC352
IC470
å IC501
çå IC701
å IC702
å IC751
IC951
IC2001
IC2040
VHiKA78S05P-1
RH-iX3253CEZZ
VHiTDA7233/-1
VHiTDA7233/-1
VHiM52055FP-1
VHiTA8427K/-1
RH-iX0758CEZZ
VHiT8889A//-1
VHiKA7809Pi-1
VHiMM1114XF1E
RH-iX3366CEZZ
VHiKiA7045A-1
or
VHiPST994C/-1
IC2101 VHiM24C16B/-1
IC3001 VHiCXA2074Q-1
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
PWB-A
PWB-A
PWB-B
PWB-H
PWB-R
DUNTKA120WEK0
DUNTKA120WEK1
DUNTK9510WEK0
DUNTK9310WEK1
DUNTK9511WEK3
–
–
–
–
–
Main Unit (27N-S300)
Main Unit (CN27S30)
CRT Unit
Front AV Unit
P-IN-P Unit
—
—
—
—
—
J
J
J
J
J
J
J
J
M
M
M
J
KA78S05P
TA1268AN
TDA7233
TDA7233
M52055FP
TA8427K
T8150
T8889A
KA7809PI
MM1114XFBE
TMPA8700CPF164
KA7045AP
J M24C16-BN6
J CXA2074Q
AD
AV
AF
AF
AH
AL
AF
AL
AE
AE
AT
AE
AG
AY
TRANSISTORS
You can substitute “VS2SC2462-C-1” or “VS2SC2412-C-1” for
“VS2SD601AR/-1”.
Q201 VS2SC2735//1E
J 2SC2735
Q301 VS2SD601AR/-1
J 2SD601AR
Q351 VS2SD601AR/-1
J 2SD601AR
Q352 VS2SD601AR/-1
J 2SD601AR
Q401 VS2SD601AR/-1
J 2SD601AR
Q402 VS2SB709AR/-1
J 2SB709AR
or
VS2SA1037KR-1
27
AC
AC
AC
AC
AC
AC
27N-S300
CN27S30
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA120WEK0/1
MAIN UNIT (Continued)
Q403
Q421
VS2SD601AR/-1
VS2SB709AR/-1
or
VS2SA1037KR-1
Q451 VS2SC3198-Y-1
Q601 VS2SC2655Y/-1
å Q602 VS2SD2539//1E
Q606 VS2SC3198-Y-1
å Q751 VS2SC1983//-2
Q752 VS2SC3198-Y-1
Q753 VS2SA1013//1E
Q821 VS2SD601AR/-1
Q822 VS2SD601AR/-1
Q901 VS2SD601AR/-1
Q902 VS2SD601AR/-1
Q903 VS2SD601AR/-1
Q904 VS2SD601AR/-1
Q921 VS2SD601AR/-1
Q922 VS2SD601AR/-1
Q923 VS2SD601AR/-1
Q924 VS2SD601AR/-1
Q2060 VS2SD601AR/-1
Q2201 VS2SD601AR/-1
Q2211 VS2SD601AR/-1
J 2SD601AR
J 2SB709AR
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
2SC3198(Y)
2SC2655Y
2SD2539
2SC3198(Y)
2SC1983
2SC3198(Y)
2SA1013
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
å
D702
å
D703
å
D704
AC
AC
AA
AE
AP
AA
AF
AA
AD
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
D705
D706
D707
D708
D709
D710
å D711
å
å
çå
çå
å
D751
D752
D753
å D754
å D755
å D756
D757
D758
D760
D761
D923
å
DIODES
You can substitute “RH-DX0475CEZZ” for “VHD1SS119//-1”.
D51
RH-EX0611GEZZ J Zener Diode, 5.1V
or
RH-EX0293CEZZ
D52
RH-EX0673GEZZ J Zener Diode, 32V
or
RH-EX0701GEZZ
D53
RH-EX0611GEZZ J Zener Diode, 5.1V
or
RH-EX0293CEZZ
D103 VHD1SS119//-1
J 1SS119
D401 VHD1SS119//-1
J 1SS119
D402 RH-EX0604GEZZ J Zener Diode, 3.9V
D451 VHD1SS119//-1
J 1SS119
D452 RH-EX0217CEZZ J Zener Diode, 15V
D453 RH-EX0217CEZZ J Zener Diode, 15V
D454 RH-EX0611GEZZ J Zener Diode, 5.1V
or
RH-EX0293CEZZ
D455 VHD1SS119//-1
J 1SS119
D456 VHD1SS119//-1
J 1SS119
D457 RH-EX0631GEZZ J Zener Diode, 9.1V
or
RH-EX0313CEZZ
D471 RH-EX0614GEZZ J Zener Diode, 5.6V
or
RH-EX0296CEZZ
D481 VHD1SS119//-1
J 1SS119
D482 VHD1SS119//-1
J 1SS119
D483 VHD1SS119//-1
J 1SS119
D484 VHD1SS119//-1
J 1SS119
D501 RH-DX0441CEZZ J Diode
å D502
RH-DX0131CEZZ J Diode
D503 RH-DX0441CEZZ J Diode
D631 RH-EX0630GEZZ J Zener Diode, 9.1V
or
RH-EX0312CEZZ
çå D651
RH-DX0131CEZZ J Diode
çå D652
RH-EX1313CEZZ J Zener Diode, 9.1V
çå D653
VHD1SS119//-1
J 1SS119
çå D654
VHD1SS119//-1
J 1SS119
å D701
RH-DX0154CEZZ J Diode
or
RH-DX0259CEZZ
D924
AA
AB
★
Part No.
RH-DX0154CEZZ
or
RH-DX0259CEZZ
RH-DX0154CEZZ
or
RH-DX0259CEZZ
RH-DX0154CEZZ
or
RH-DX0259CEZZ
VHD1SS119//-1
RH-EX0238CEZZ
VHSS6785GLB2E
VHSS6785GLB2E
RH-DX0131CEZZ
RH-DX0131CEZZ
RH-DX0229CEZZ
or
RH-DX0444CEZZ
RH-DX0441CEZZ
RH-EX0019TAZZ
RH-DX0441CEZZ
RH-DX0441CEZZ
RH-DX0441CEZZ
RH-DX0441CEZZ
VHD1SS119//-1
RH-DX0441CEZZ
RH-DX0441CEZZ
RH-DX0441CEZZ
RH-EX0631GEZZ
or
RH-EX0313CEZZ
RH-EX0631GEZZ
or
RH-EX0313CEZZ
Description
Code
J Diode
AC
J Diode
AC
J Diode
AC
J
J
J
J
J
J
J
1SS119
Zener Diode, 75V
Si.Control Rectifier
Si.Control Rectifier
Diode
Diode
Diode
AB
AC
AL
AL
AC
AC
AF
J
J
J
J
J
J
J
J
J
J
J
Diode
Zener Diode, 12V
Diode
Diode
Diode
Diode
1SS119
Diode
Diode
Diode
Zener Diode, 9.1V
AC
AB
AC
AC
AC
AC
AB
AC
AC
AC
AA
J Zener Diode, 9.1V
AA
PACKAGED CIRCUITS
å
AA
AB
AB
AB
AB
AB
AB
AA
PR701 RMPTP0092CEZZ J Packaged Circuit
(L702:G0038ME)
X801 RCRSB0001PEZZ R Crystal
AH
AL
FILTERS
CF301
CF401
CF631
CF2040
SF201
RFiLC0029TAZZ
RFiLC0013CEZZ
RFiLA0034CEZZ
RFiLC0121GEZZ
RFiLC0405CEZZ
J
J
J
J
J
Ceramic Filter
Ceramic Filter
Ceramic Filter
Ceramic Filter
SAW Filter
AD
AE
AD
AD
AH
COILS
DL421 RCiLZ0938CEZZ
L201 VP-XF1R2K0000
L202 RCiLi0588CEZZ
or
RCiLi0622CEZZ
L301 VP-XF8R2K0000
L302 RCiLi0613CEZZ
or
RCiLi0605CEZZ
L401 VP-XF6R8K0000
L402 VP-XF3R3K0000
L403 VP-XF8R2K0000
L404 VP-XF8R2K0000
L601 RCiLZ0102MEZZ
or
RCiLZ0101MEZZ
å L701
RCiLF0070PEZZ
or
RCiLF0025PEZZ
or
RCiLF0087PEZZ
or
RCiLF0235CEZZ
å L701
RCiLF0090CEZZ
L821 VP-XF680K0000
L2040 RCiLB0131CEZZ
AB
AB
AA
AA
AB
AB
AB
AB
AC
AC
AC
AA
AC
AD
AB
AB
AC
28
J Comb Filter
J Peaking 1.2µH
J IF Coil
AW
AB
AF
J Peaking 8.2µH
J IF Coil
AB
AE
J
J
J
J
M
AB
AB
AB
AB
AE
Peaking 6.8µH
Peaking 3.3µH
Peaking 8.2µH
Peaking 8.2µH
Coil
M Coil
AD
J Coil (CN27S30)
J Peaking 68µH
J Oscillation Coil
AL
AB
AE
27N-S300
CN27S30
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKA120WEK0/1
C505
C507
C508
C509
C510
C511
C512
C513
C514
C551
C552
C603
C604
çå C607
çå C608
C612
C614
C631
C632
C633
C652
C653
å C701
MAIN UNIT (Continued)
TRANSFORMERS
å
çå
å
å
T601
T602
T701
T701
RTRNZ0168CEZZ J H-Driver
RTRNF0041MEZZ M H-Out
RTRNP0533CEZZ M Power Trans.
RTRNP0549CEZZ M Power Trans.
(CN27S30)
AH
BA
AK
AM
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
C51
VCEA0A1CW476M J 47
16V EL.
C53
VCEA0A1HW105M J 1
50V EL.
C54
VCEA0A1HW475M J 4.7
50V EL.
C55
VCEA0A1CW108M J 1000 16V EL.
C103 VCEA0A1CW228M J 2200 16V EL.
C201 VCKYMN1HB102K J 1000p 50V Ceramic
C202 VCKYCY1HF103Z J 0.01 50V Ceramic
C203 VCKYCY1HB102K J 1000p 50V Ceramic
C204 VCKYMN1CY103N J 0.01 16V Ceramic
C205 VCEA0A1HW474M J 0.47 50V EL.
C206 VCEA0A1CW337M J 330
16V EL.
C207 VCKYMN1CY103N J 0.01 16V Ceramic
C208 VCEA0A1HW474M J 0.47 50V EL.
C209 VCKYCY1HB222K J 2200p 50V Ceramic
C210 VCKYMN1HB102K J 1000p 50V Ceramic
C301 VCCCCY1HH330J J 33p
50V Ceramic
C302 VCCCCY1HH151J J 150p 50V Ceramic
C303 VCCCCY1HH390J J 39p
50V Ceramic
C307 VCCCCY1HH1R5C J 1.5p 50V Ceramic
C308 VCKYCY1HB102K J 1000p 50V Ceramic
C309 VCEA0A1CW337M J 330
16V EL.
C351 VCKYCY1HB392K J 3900p 50V Ceramic
C352 VCEA0A1CW107M J 100
16V EL.
C353 VCEA0A1CW337M J 330
16V EL.
C354 VCKYCY1CB104K J 0.1
16V Ceramic
C355 VCEA0A1CW226M J 22
16V EL.
C356 VCKYCY1HB392K J 3900p 50V Ceramic
C357 VCEA0A1CW107M J 100
16V EL.
C358 VCEA0A1CW337M J 330
16V EL.
C359 VCKYCY1CB104K J 0.1
16V Ceramic
C360 VCEA0A1CW226M J 22
16V EL.
C361 VCEA0A1CW477M J 470
16V EL.
C362 VCEA0A1CW476M J 47
16V EL.
C401 VCKYMN1HB331K J 330p 50V Ceramic
C402 VCKYMN1HB101K J 100p 50V Ceramic
C403 VCKYCY1CB104K J 0.1
16V Ceramic
C404 VCEA0A1HW106M J 10
50V EL.
C405 VCEA0A1HW335M J 3.3
50V EL.
C406 VCEA0A1HW225M J 2.2
50V EL.
C407 VCKYCY1CB104K J 0.1
16V Ceramic
C408 VCEA0A1HW106M J 10
50V EL.
C409 VCEA0A1HW335M J 3.3
50V EL.
C410 VCQYTA1HM104K J 0.1
50V Mylar
C411 VCEA0A1CW337M J 330
16V EL.
C412 VCKYCY1HB103K J 0.01 50V Ceramic
C413 VCKYCY1HB103K J 0.01 50V Ceramic
C422 VCEA0A1CW476M J 47
16V EL.
C423 VCEA0A1CW476M J 47
16V EL.
C451 VCQYTA1HM104K J 0.1
50V Mylar
C452 VCEA0A1HW475M J 4.7
50V EL.
C453 VCEA0A2EW226M J 22
250V EL.
C454 VCEA0A1VW226M J 22
35V EL.
C471 VCKYPA1HB103K J 0.01 50V Ceramic
C472 VCEA0A1HW106M J 10
50V EL.
C473 VCEA0A1HW106M J 10
50V EL.
C474 VCEA0A1HW106M J 10
50V EL.
C475 VCEA0A1HW106M J 10
50V EL.
C476 VCKYCY1HB103K J 0.01 50V Ceramic
C477 VCEA0A1HW106M J 10
50V EL.
C478 VCKYCY1HB103K J 0.01 50V Ceramic
C502 VCEA0A1VW108M J 1000 35V EL.
C504 VCKYPA2HB391K J 390p 500V Ceramic
AB
AB
AB
AD
AD
AA
AA
AA
AA
AB
AC
AA
AB
AA
AA
AA
AA
AA
AD
AA
AC
AA
AC
AC
AB
AB
AA
AC
AC
AB
AB
AC
AB
AA
AA
AB
AB
AB
AB
AB
AB
AB
AC
AC
AA
AA
AB
AB
AC
AB
AE
AB
AA
AB
AB
AB
AB
AA
AB
AA
AD
AA
C702
C703
C704
å C705
å
C706
C707
C708
C709
C710
C711
C712
å C713
C714
çå C715
C717
C721
å C722
C751
C753
C754
C756
C801
C802
C803
C804
C805
C806
C807
C821
C822
C823
C824
C825
C901
C902
C903
C908
C909
C910
C911
C922
C923
C925
C926
C927
29
Part No.
VCQYTA1HM473K
VCQYTA1HM103K
VCEA0A1VW107M
VCKYCY1HB182K
VCEA0A1VW108M
VCFYSA1JB473J
VCFYSA1JB564J
VCEA0A1HW474M
VCSATA1VE684K
VCSATA1CE225K
VCEA0A1HW225M
VCQYTA1HM273K
VCEA0A1EW227M
VCFPVC3CA662H
VCFPVC3CA662H
VCFPVC2DB474J
VCKYPA2HB331K
VCEA0A1HW335M
VCQYTA1HM103K
VCEA0A1HW105M
VCEA0A1HW106M
VCEA0A1HW106M
RC-FZ017SCEZZ
or
RC-FZ1011CEZZ
or
RC-FZ012SGEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
VCKYPA2HB472K
RC-EZ0722CEZZ
or
RC-EZ0802CEZZ
RC-KZ0092GEZZ
or
RC-KZ0031CEZZ
VCKYPA2HB272K
VCKYPA2HB391K
RC-QZ0010CEZZ
RC-QZ0010CEZZ
VCKYPA2HB391K
VCKYPA2HB272K
RC-EZ0696CEZZ
VCQYTA1HM273K
VCQYTA1HM103K
VCEA0A1HW106M
VCEA0A1EW477M
VCKYPA2HB152K
VCEA0A1EW476M
VCEA0A1VW337M
VCEA0A1CW107M
VCEA0A1CW337M
VCQYTA1HM223K
VCEA0A1HW474M
VCCCCY1HH110J
VCKYCY1CB104K
VCKYCY1CB104K
VCKYCY1CB104K
VCCCCY1HH221J
VCKYCY1HB102K
VCCCCY1HH150J
VCCCCY1HH150J
VCKYCY1HB103K
VCKYCY1HB103K
VCEA0A1HW335M
VCEA0A1CW476M
VCEA0A1HW335M
VCEA0A1HW225M
VCEA0A1HW225M
VCKYCY1HB681K
VCKYCY1HB681K
VCEA0A1HW335M
VCEA0A1HW335M
VCEA0A1CW476M
VCEA0A1CW476M
VCKYCY1HB103K
★
Description
Code
J
J
J
J
J
M
M
J
J
J
J
J
J
M
M
J
J
J
J
J
J
J
J
0.047
0.01
100
1800p
1000
0.047
0.56
0.47
0.68
2.2
2.2
0.027
220
6600p
6600p
0.47
330p
3.3
0.01
1
10
10
0.22
50V Mylar
AB
50V Mylar
AB
35V EL.
AC
50V Ceramic
AA
35V EL.
AD
63V Mylar
AB
63V Mylar
AC
50V EL.
AB
35V Tantalum(N.P) AC
16V Tantalum(N.P) AB
50V EL.
AB
50V Mylar
AB
25V EL.
AB
1600V M-Poly.
AC
1600V M-Poly.
AC
200V M-Poly.
AE
500V Ceramic
AA
50V EL.
AB
50V Mylar
AB
50V EL.
AB
50V EL.
AB
50V EL.
AB
AC250V Plastic
AD
J
J
J
M
0.01
0.01
4700p
820
AC250V Ceramic
AC250V Ceramic
500V Ceramic
200V EL.
AC
AC
AB
AL
J 0.0033 AC250V Ceramic
AC
J
J
J
J
J
J
M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AC
AC
AA
AA
AG
AB
AB
AB
AD
AA
AB
AD
AC
AC
AB
AB
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AA
2700p
390p
0.01
0.01
390p
2700p
220
0.027
0.01
10
470
1500p
47
330
100
330
0.022
0.47
11p
0.1
0.1
0.1
220p
1000p
15p
15p
0.01
0.01
3.3
47
3.3
2.2
2.2
680p
680p
3.3
3.3
47
47
0.01
500V
500V
250V
250V
500V
500V
160V
50V
50V
50V
25V
500V
25V
35V
16V
16V
50V
50V
50V
16V
16V
16V
50V
50V
50V
50V
50V
50V
50V
16V
50V
50V
50V
50V
50V
50V
50V
16V
16V
50V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
Mylar
Mylar
EL.
EL.
Ceramic
EL.
EL.
EL.
EL.
Mylar
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
EL.
EL.
EL.
EL.
Ceramic
Ceramic
EL.
EL.
EL.
EL.
Ceramic
27N-S300
CN27S30
Ref. No.
★
Part No.
Description
Code
Ref. No.
RJ43
RJ45
RJ47
RJ48
RJ49
RJ50
RJ52
RJ53
RJ54
RJ58
RJ59
RJ60
RJ62
RJ63
RJ65
RJ66
RJ68
RJ69
RJ73
RJ75
RJ76
RJ77
RJ80
RJ81
RJ82
RJ83
RJ84
RJ86
RJ87
RJ91
RJ92
RJ93
RJ94
RJ95
RJ96
RJ97
RJ98
RJ102
RJ104
RJ105
RJ106
RJ108
RJ109
RJ110
å R51
å R52
å R53
R54
R55
R56
R57
R201
R202
R203
R204
R205
R206
R208
R301
R302
R303
R304
R305
R306
R351
R352
R353
R354
R356
R357
R358
R359
R401
R402
R403
R404
PWB-A: DUNTKA120WEK0/1
MAIN UNIT (Continued)
C928
C929
C930
C931
C932
C951
C952
C953
C954
C955
C2001
C2002
C2040
C2041
C2060
C2061
C2062
C2201
C2211
C2601
C2602
C3001
C3002
C3003
C3004
C3005
C3006
C3007
C3008
C3009
C3010
C3011
C3012
C3013
C3014
C3015
C3016
C3017
C3018
C3019
C3020
C3021
C3022
VCKYCY1HB103K
VCEA0A1HW106M
VCEA0A1HW106M
VCKYCY1EB183K
VCKYCY1EB183K
VCEA0A1HW106M
VCEA0A1HW106M
VCEA0A1HW106M
VCKYCY1HF103Z
VCEA0A1HW106M
VCCCCY1HH101J
VCCCCY1HH101J
VCEA0A1AW107M
VCEA0A1HW105M
VCKYCY1CB104K
VCKYMN1HB101K
VCEA0A1AW107M
VCKYCY1HB152K
VCCCCY1HH390J
VCEA0A1HW475M
VCKYMN1HB101K
VCE9GA1HW475M
VCKYCY1HB562K
VCQYTA1HM123K
VCEA0A1HW105M
VCEA0A1HW475M
VCEA0A1HW106M
VCEA0A1HW475M
VCKYMN1CY103N
VCEA0A1CW227M
VCE9GA1HW475M
VCEA0A1HW475M
VCE9GA1HW475M
VCKYCY1HB272K
VCQYTA1HM473K
VCSATA1CE335K
VCE9GA1HW475M
VCSATA1CE106K
VCEA0A1HW105M
VCEA0A1HW475M
VCEA0A1HW475M
VCEA0A1HW475M
VCEA0A1HW475M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
0.01
10
10
0.018
0.018
10
10
10
0.01
10
100p
100p
100
1
0.1
100p
100
1500p
39p
4.7
100p
4.7
5600p
0.012
1
4.7
10
4.7
0.01
220
4.7
4.7
4.7
2700p
0.047
3.3
4.7
10
1
4.7
4.7
4.7
4.7
50V
50V
50V
25V
25V
50V
50V
50V
50V
50V
50V
50V
10V
50V
16V
50V
10V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
16V
16V
50V
50V
50V
50V
50V
16V
50V
16V
50V
50V
50V
50V
50V
Ceramic
AA
EL.
AB
EL.
AB
Ceramic
AA
Ceramic
AA
EL.
AB
EL.
AB
EL.
AB
Ceramic
AA
EL.
AB
Ceramic
AA
Ceramic
AA
EL.
AB
EL.
AB
Ceramic
AB
Ceramic
AA
EL.
AB
Ceramic
AA
Ceramic
AA
EL.
AB
Ceramic
AA
EL.(N.P)
AB
Ceramic
AA
Mylar
AA
EL.
AB
EL.
AB
EL.
AB
EL.
AB
Ceramic
AA
EL.
AC
EL.(N.P)
AB
EL.
AB
EL.(N.P)
AB
Ceramic
AA
Mylar
AB
Tantalum(N.P) AC
EL.(N.P)
AB
Tantalum(N.P) AD
EL.
AB
EL.
AB
EL.
AB
EL.
AB
EL.
AB
RJ1
RJ2
RJ3
RJ4
RJ6
RJ9
RJ12
RJ13
RJ14
RJ15
RJ16
RJ17
RJ18
RJ19
RJ20
RJ21
RJ26
RJ27
RJ28
RJ30
RJ31
RJ32
RJ35
RJ38
RJ39
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRD-MN2BE000J J 0
1/8W
Carbon
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRD-MN2BE000J J 0
1/8W
Carbon
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRD-MN2BE000J J 0
1/8W
Carbon
RESISTORS
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
30
Part No.
★
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRS-CY1JF1R0J
J 1
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRD-MN2BE000J J 0
VRS-CY1JF000J
J 0
VRS-CY1JF000J
J 0
VRS-RG3AB391J M 390
VRS-RG3AB470J J 47
VRS-RG3LB333J J 33k
VRS-CY1JF101J
J 100
VRD-MN2BE101J J 100
VRD-MN2BE823J J 82k
VRD-MN2BE392J J 3.9k
VRD-MN2BE151J J 150
VRD-MN2BE122J J 1.2k
VRD-MN2BE682J J 6.8k
VRD-MN2BE270J J 27
VRS-CY1JF331J
J 330
VRD-RA2BE121J J 120
VRD-MN2BE331J J 330
VRD-RA2BE222J J 2.2k
VRS-CY1JF102J
J 1k
VRD-MN2BE103J J 10k
VRD-MN2BE333J J 33k
VRS-CY1JF102J
J 1k
VRS-CY1JF152J
J 1.5k
VRS-CY1JF333J
J 33k
VRD-MN2BE472J J 4.7k
VRD-MN2BE4R7J J 4.7
VRS-CY1JF152J
J 1.5k
VRS-CY1JF472J
J 4.7k
VRD-MN2BE4R7J J 4.7
VRS-CY1JF152J
J 1.5k
VRS-CY1JF333J
J 33k
VRD-MN2BE682J J 6.8k
VRS-CY1JF331J
J 330
VRS-CY1JF391J
J 390
VRD-MN2BE102J J 1k
Description
1/16W
1/8W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/8W
1/16W
1/16W
1W
1W
3W
1/16W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/16W
1/8W
1/8W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
27N-S300
CN27S30
Ref. No.
Part No.
★
Description
Code
Ref. No.
R708
R709
R710
R711
R712
R713
å R714
å R715
R716
R717
R718
å R719
R751
R752
R754
å R755
R757
å R760
å R761
R801
R802
R803
R804
R805
R806
R821
R822
R823
R824
R825
R826
R827
R828
R829
R901
R903
R904
R905
R906
R907
R908
R910
R911
R912
R913
R914
R915
R920
R922
R923
R925
R926
R927
R930
R931
R932
R933
R934
R935
R936
R937
R938
R939
R940
R941
R942
R943
R951
R952
R953
R954
R961
R962
R2001
R2002
R2004
å
å
å
å
PWB-A: DUNTKA120WEK0/1
MAIN UNIT (Continued)
R405
R406
R407
R408
R409
R410
R411
R412
R413
R414
R415
R420
R421
R423
R424
å R451
R452
R453
R454
R455
R456
R457
R458
R459
å R466
å R467
å R468
R473
R481
R482
R483
R501
R502
R503
R504
R505
R506
R510
å R511
R512
R516
R518
R521
R551
R552
R553
R554
R601
R602
å R603
å R604
R605
R606
R608
å R609
å R610
R611
R631
R632
R633
R634
çå R651
çå R652
çå R653
çå R654
çå R655
å R701
å R702
R704
R705
å R706
å R707
VRS-CY1JF470J
VRS-CY1JF680J
VRS-CY1JF102J
VRS-CY1JF471J
VRD-MN2BE562J
VRD-RA2BE823J
VRD-MN2BE332J
VRD-RA2BE561J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF332J
VRS-CY1JF152J
VRS-CY1JF152J
VRD-MN2BE102J
VRS-RG2HC103J
VRD-MN2BE103J
VRD-RA2EE393J
VRD-RM2HD104J
VRD-RA2BE152J
VRS-CY1JF682J
VRS-CY1JF102J
VRS-RG3DB332J
VRD-MN2BE102J
VRN-RL3DB5R6J
VRN-RL3ABR22J
VRN-RL3DB5R6J
VRS-CY1JF102J
VRD-MN2BE682J
VRD-MN2BE223J
VRS-CY1JF223J
VRD-RA2BE124G
VRD-RA2BE823G
VRD-RA2BE473J
VRD-MN2BE471J
VRD-MN2BE101J
VRS-CY1JF223J
VRN-RL3AB1R0J
VRN-RL3ABR56J
VRS-RG3AB391J
VRD-MN2BE562J
VRD-MN2BE184J
VRD-RA2BE153G
VRS-CY1JF472J
VRS-CY1JF102J
VRD-MN2BE333J
VRD-MN2BE333J
VRD-MN2BE331J
VRD-RM2HD560J
VRS-RG3LB120J
VRN-RL3LBR56J
VRS-RG2HC102J
VRD-MN2BE102J
VRD-MN2BE101J
VRS-RG3LB120J
VRN-RL3LBR56J
VRD-MN2BE332J
VRS-CY1JF391J
VRD-MN2BE152J
VRS-CY1JF472J
VRD-RM2HD101J
VRS-RG2HC270J
VRD-MN2BE221J
VRN-RA2BK822F
VRN-RA2BK682F
VRS-CY1JF104J
RR-HZ0046CEZZ
VRW-KQ3NC1R2K
VRD-RM2HD223J
VRD-RM2HD223J
VRS-RG2HC151J
VRS-KA3NG331K
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
M
J
M
M
M
J
J
J
J
J
J
J
J
J
J
M
J
M
J
J
J
J
J
J
J
J
J
M
M
J
J
J
M
M
J
J
J
J
J
M
J
J
J
J
J
J
J
J
J
M
47
68
1k
470
5.6k
82k
3.3k
560
100
100
100
3.3k
1.5k
1.5k
1k
10k
10k
39k
100k
1.5k
6.8k
1k
3.3k
1k
5.6
0.22
5.6
1k
6.8k
22k
22k
120k
82k
47k
470
100
22k
1
0.56
390
5.6k
180k
15k
4.7k
1k
33k
33k
330
56
12
0.56
1k
1k
100
12
0.56
3.3k
390
1.5k
4.7k
100
27
220
8.2k
6.8k
100k
2.7
1.2
22k
22k
150
330
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/2W
1/8W
1/4W
1/2W
1/8W
1/16W
1/16W
2W
1/8W
2W
1W
2W
1/16W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/8W
1/8W
1/16W
1W
1W
1W
1/8W
1/8W
1/8W
1/16W
1/16W
1/8W
1/8W
1/8W
1/2W
3W
3W
1/2W
1/8W
1/8W
3W
3W
1/8W
1/16W
1/8W
1/16W
1/2W
1/2W
1/8W
1/8W
1/8W
1/16W
1/2W
7W
1/2W
1/2W
1/2W
7W
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Film
M-Film
M-Film
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Film
M-Film
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Film
M-Ox.
Carbon
Carbon
M-Ox.
M-Film
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
M-Film
M-Film
M-Ox.
Solid
Cement
Carbon
Carbon
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AE
AA
AA
AA
AC
31
Part No.
VRD-RM2HD330J
VRS-KA3NG331K
VRD-RM2HD330J
VRN-GA2EB1R0J
VRD-RA2BE822J
VRD-RM2HD681J
VRS-KA3NG3R3K
VRW-KQ4AC2R7K
VRD-RM2HD223J
VRN-GA2EB1R0J
VRN-RL3AB2R7J
VRN-RL3LBR56J
VRD-RM2HD471J
VRD-MN2BE392J
VRD-MN2BE223J
VRS-RG3LB180J
VRD-MN2BE472J
VRS-RG3AB150J
VRN-RL3AB4R7J
VRD-MN2BE332J
VRD-MN2BE332J
VRS-CY1JF222J
VRS-CY1JF222J
VRS-CY1JF222J
VRD-MN2BE333J
VRS-CY1JF682J
VRS-CY1JF183J
VRS-CY1JF471J
VRS-CY1JF102J
VRS-CY1JF152J
VRS-CY1JF562J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF102J
VRD-RA2BE331J
VRD-MN2BE102J
VRS-CY1JF683J
VRS-CY1JF223J
VRS-CY1JF392J
VRS-CY1JF182J
VRS-CY1JF102J
VRD-MN2BE102J
VRS-CY1JF683J
VRS-CY1JF223J
VRS-CY1JF392J
VRS-CY1JF182J
VRS-CY1JF102J
VRD-MN2BE101J
VRS-CY1JF102J
VRS-CY1JF102J
VRD-MN2BE104J
VRD-MN2BE104J
VRD-RA2BE750J
VRS-CY1JF563J
VRD-MN2BE333J
VRS-CY1JF102J
VRS-CY1JF122J
VRS-CY1JF473J
VRS-CY1JF750J
VRD-MN2BE473J
VRD-MN2BE102J
VRS-CY1JF122J
VRD-MN2BE122J
VRD-MN2BE122J
VRD-MN2BE183J
VRD-MN2BE273J
VRD-MN2BE102J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-MN2BE750J
VRD-MN2BE750J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE102J
VRS-CY1JF103J
VRD-MN2BE473J
★
J
M
J
J
J
J
J
J
J
J
M
M
J
J
J
J
J
M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
33
330
33
1
8.2k
680
3.3
2.7
22k
1
2.7
0.56
470
3.9k
22k
18
4.7k
15
4.7
3.3k
3.3k
2.2k
2.2k
2.2k
33k
6.8k
18k
470
1k
1.5k
5.6k
10k
10k
1k
330
1k
68k
22k
3.9k
1.8k
1k
1k
68k
22k
3.9k
1.8k
1k
100
1k
1k
100k
100k
75
56k
33k
1k
1.2k
47k
75
47k
1k
1.2k
1.2k
1.2k
18k
27k
1k
100
100
75
75
100
100
1k
10k
47k
1/2W
7W
1/2W
1/4W
1/8W
1/2W
7W
10W
1/2W
1/4W
1W
3W
1/2W
1/8W
1/8W
3W
1/8W
1W
1W
1/8W
1/8W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
1/8W
1/8W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/8W
1/16W
1/8W
Carbon
M-Ox.
Carbon
M-Film
Carbon
Carbon
M-Ox.
Cement
Carbon
M-Film
M-Film
M-Film
Carbon
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
M-Film
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Code
AA
AC
AA
AA
AA
AA
AD
AE
AA
AA
AA
AB
AA
AA
AA
AD
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
27N-S300
CN27S30
Ref. No.
Part No.
★
Description
Code
Ref. No.
S2501
S2502
S2503
S2504
S2505
MAIN UNIT (Continued)
VRS-CY1JF102J
VRD-MN2BE102J
VRD-RA2BE102J
VRS-CY1JF102J
VRD-RA2BE102J
VRS-CY1JF471J
VRS-CY1JF223J
VRD-RA2BE682J
VRD-RA2BE682J
VRD-MN2BE682J
VRD-MN2BE682J
VRS-CY1JF102J
VRS-CY1JF103J
VRD-RA2BE103J
VRS-CY1JF223J
VRS-CY1JF223J
VRS-CY1JF102J
VRS-CY1JF333J
VRS-CY1JF101J
VRD-MN2BE333J
VRS-CY1JF682J
VRS-CY1JF101J
VRD-RA2BE101J
VRD-MN2BE101J
VRS-CY1JF562J
VRD-MN2BE101J
VRS-CY1JF562J
VRD-MN2BE183J
VRD-MN2BE222J
VRD-RA2BE332J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF102J
VRD-RA2BE102J
VRS-CY1JF102J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-MN2BE222J
VRS-CY1JF103J
VRS-CY1JF184J
VRD-MN2BE222J
VRS-CY1JF682J
VRS-CY1JF333J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-MN2BE103J
VRD-MN2BE273J
VRD-MN2BE123J
VRD-MN2BE563J
VRD-MN2BE563J
VRD-MN2BE823J
VRD-MN2BE153J
VRD-MN2BE272J
VRD-RA2BE331J
VRD-RA2BE221J
VRD-RA2BE221J
VRS-CY1JF105J
VRS-CY1JF104J
VRS-CY1JF623J
VRS-CY1JF332J
VRS-CY1JF302J
VRD-MN2BE392J
VRD-RA2BE102J
VRS-CY1JF102J
VRD-MN2BE104J
VRD-MN2BE104J
VRD-RA2BE102J
VRD-RA2BE102J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
1k
1k
1k
1k
1k
470
22k
6.8k
6.8k
6.8k
6.8k
1k
10k
10k
22k
22k
1k
33k
100
33k
6.8k
100
100
100
5.6k
100
5.6k
18k
2.2k
3.3k
1k
10k
1k
1k
1k
1k
100
100
2.2k
10k
180k
2.2k
6.8k
33k
100
100
100
100
10k
27k
12k
56k
56k
82k
15k
2.7k
330
220
220
1M
100k
62k
3.3k
3k
3.9k
1k
1k
100k
100k
1k
1k
1/16W
1/8W
1/8W
1/16W
1/8W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
1/8W
1/16W
1/8W
1/16W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/8W
1/8W
1/8W
1/8W
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Description
Code
SWITCHES
PWB-A: DUNTKA120WEK0/1
R2006
R2008
R2009
R2010
R2011
R2012
R2020
R2024
R2025
R2026
R2027
R2028
R2029
R2032
R2035
R2036
R2040
R2041
R2042
R2043
R2044
R2045
R2046
R2047
R2048
R2060
R2061
R2062
R2063
R2064
R2065
R2067
R2069
R2071
R2072
R2073
R2101
R2102
R2201
R2202
R2203
R2211
R2212
R2213
R2401
R2402
R2403
R2404
R2501
R2503
R2504
R2505
R2506
R2507
R2508
R2509
R2601
R3001
R3002
R3003
R3004
R3005
R3007
R3008
R3010
R3011
R3012
R3013
R3014
R3017
R3018
★
Part No.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
QSW-K0202PEZZ
QSW-K0202PEZZ
QSW-K0202PEZZ
QSW-K0202PEZZ
QSW-K0202PEZZ
R
R
R
R
R
Power
Vol-down
Vol-up
CH-down
CH-up
AC
AC
AC
AC
AC
MISCELLANEOUS PARTS
FB601
FB701
FB702
FH701
FH702
å F701
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
QFSHD1013CEZZ
QFSHD1014CEZZ
QFS-B4023CEZZ
or
QFS-B4021GEZZ
J921 QSOCD0430CEZZ
JA216 RBLN-0037CEZZ
P602 QPLGN0160FJZZ
P651 QPLGN0361CEZZ
P701 QPLGN0207CEZZ
P702 QPLGN0461CEZZ
P703 QPLGN0269GEZZ
P901 QPLGN0561CEZZ
P902 QPLGN0461CEZZ
P903 QPLGN0561CEZZ
P2401 QPLGN0561CEZZ
RDA501 PRDAR0234PEFW
RDA604 PRDAR0233PEFW
RDA707 PRDAR0026PEFW
RDA708 PRDAR0026PEFW
RDA751 PRDAR5072CEFW
RDA752 PRDAR5072CEFW
RMC2601 RRMCU0227CEZZ
or
RRMCU0224CEZZ
or
RRMCU0216CEZZ
or
RRMCU0232CEZZ
å RY701 RRLYU0036CEZZ
or
RRLYU0038CEZZ
TAN921 QTANJ0523CEZZ
LX-BZ3049GEFD
32
J
J
J
J
J
J
Ferrite Bead
Ferrite Bead
Ferrite Bead
Fuse Holder
Fuse Holder
Fuse 4A(125V)
AB
AB
AB
AC
AC
AC
J
J
J
J
J
J
J
J
J
J
J
R
R
R
R
J
J
J
Socket, S-Video
Ferrite Bead
Plug 5-pin (K)
Plug 3-pin
Plug 2-pin (M)
Plug 4-pin (YBN)
Plug 2-pin (P)
Plug 5-pin (HA)
Plug 4-pin (S)
Plug 5-pin (GBN)
Plug 5-pin
Heat Sink, for IC501
Heat Sink, for Q602
Heat Sink, for D707
Heat Sink, for D708
Heat Sink, for Q751
Heat Sink, for IC751
Remote Receiver
AE
AB
AD
AB
AA
AB
AB
AB
AB
AB
AB
AH
AK
AD
AD
AC
AC
AK
J Relay
AM
M AV Terminal
J Screw
AG
AA
27N-S300
CN27S30
Ref. No.
★
Part No.
Description
Code
Ref. No.
Q853
Q854
Q855
Q856
Q881
PWB-C: DUNTK9310WEK1
CRT UNIT
FRONT AV UNIT
VS2SC3198-Y-1
VS2SC3789//2E
or
VS2SC3619LB-1
VS2SC3198-Y-1
VS2SC3789//2E
or
VS2SC3619LB-1
VS2SC3198-Y-1
VS2SC3789//2E
or
VS2SC3619LB-1
VS2SA1266-Y-1
AA
AF
J 2SC3198(Y)
J 2SC3789
AA
AF
J 2SC3198(Y)
J 2SC3789
AA
AF
J 2SA1266(Y)
AA
You can substitute “RH-DX0475CEZZ” for “VHD1SS119//-1”.
D881 VHD1SS119//-1
J 1SS119
D882 VHD1SS119//-1
J 1SS119
D884 VHD1SS119//-1
J 1SS119
J1001
J1002
J1003
P1001
C883
[M-Ox.··· Metal Oxide]
VRD-RA2BE470J J 47 1/8W
VRD-RA2BE181J J 180 1/8W
VRD-RA2BE121J J 120 1/8W
VRD-RA2BE471J J 470 1/8W
VRD-RA2BE221J J 220 1/8W
VRS-VV3LB123J
J 12k 3W
VRD-RM2HD222J J 2.2k 1/2W
VRD-RA2BE470J J 47 1/8W
VRD-RA2BE181J J 180 1/8W
VRD-RA2BE121J J 120 1/8W
VRD-RA2BE471J J 470 1/8W
VRD-RA2BE221J J 220 1/8W
VRS-VV3LB123J
J 12k 3W
VRD-RM2HD222J J 2.2k 1/2W
VRD-RA2BE470J J 47 1/8W
VRD-RA2BE181J J 180 1/8W
VRD-RA2BE121J J 120 1/8W
VRD-RA2BE471J J 470 1/8W
VRD-RA2BE221J J 220 1/8W
VRS-VV3LB123J
J 12k 3W
VRD-RM2HD222J J 2.2k 1/2W
VRD-RA2BE102J J 1k 1/8W
VRD-RA2BE271J J 270 1/8W
VRD-RA2BE561J J 560 1/8W
VRD-RA2BE152J J 1.5k 1/8W
VRD-RA2BE470J J 47 1/8W
AD
AD
AC
AB
INTEGRATED CIRCUITS
IC1701 VHiMM1117XF1E
IC1781 VHiKA7805Pi-1
IC1801 VHiM65667FP-2
AB
AB
AB
M MM1117XFBE
R KA7805PI
J M65667FP
You can substitute “VS2SC2462-C-1” or “VS2SC2412-C-1” for
“VS2SD601AR/-1”.
Q1721 VS2SD601AR/-1
J 2SD601AR
Q1741 VS2SB709AR/-1
J 2SB709AR
or
VS2SA1037KR-1
Q1742 VS2SB709AR/-1
J 2SB709AR
or
VS2SA1037KR-1
Q1761 VS2SB709AR/-1
J 2SB709AR
or
VS2SA1037KR-1
Q1762 VS2SB709AR/-1
J 2SB709AR
or
VS2SA1037KR-1
Q1791 VS2SC1959Y/1E
J 2SC1959Y
Q1861 VS2SB709AR/-1
J 2SB709AR
or
VS2SA1037KR-1
Q1881 VS2SD601AR/-1
J 2SD601AR
Q1882 VS2SD601AR/-1
J 2SD601AR
Q1883 VS2SD601AR/-1
J 2SD601AR
AB
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
AA
AA
AA
AC
AB
RESISTORS
R851
R852
R853
R855
R856
å R857
R858
R859
R860
R861
R863
R864
å R865
R866
R867
R868
R869
R871
R872
å R873
R874
R881
R882
R883
R884
R895
Jack, Video in
Jack, Audio in (L)
Jack, Audio in (R)
Plug 5-pin (HA)
AD
AE
BC
TRANSISTORS
J Peaking 82µH
[EL.··· Electrolytic]
VCCSPA1HL391J J 390p 50V
VCCSPA1HL331J J 330p 50V
VCCSPA1HL391J J 390p 50V
RC-KZ0024CEZZ J 0.001 2kV
or
VCKYPB3DE472Z
0.0047 2kV
VCEA0A1HW106M J 10
50V
J
J
J
J
P-IN-P UNIT
CAPACITORS
C851
C852
C853
C854
QJAKE0053GEZZ
QJAKE0055GEZZ
QJAKE0059GEZZ
QPLGN0541CEZZ
PWB-R: DUNTK9511WEK3
COIL
VP-MK820K0000
Code
MISCELLANEOUS PARTS
J 2SC3198(Y)
J 2SC3789
DIODES
L851
Description
PWB-B: DUNTK9510WEK0
TRANSISTORS
Q851
Q852
★
Part No.
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AC
AC
AC
AC
AC
AC
AC
AC
DIODES
You can subsitute “RH-DX0475CEZZ” for “VHD1SS119//-1”.
D1791 RH-EX0604GEZZ J Zener Diode, 4.3V
D1801 VHD1SS119//-1
J 1SS119
D1821 VHD1SS119//-1
J 1SS119
AB
AB
AB
PACKAGED CIRCUIT
X1861 RCRSB0283CEZZ J Crystal
or
RCRSB0241CEZZ
AG
COILS
L1721
L1801
L1821
L1861
L1862
L1863
MISCELLANEOUS PARTS
P851 QPLGN0541CEZZ J Plug 5-pin (GBN)
P852 QPLGN0441CEZZ J Plug 4-pin (YBN)
SC851 QSOCV0937CEZZ J CRT Socket
AC
AC
VP-XF680K0000
VP-XF100K0000
VP-XF100K0000
VP-XF100K0000
VP-XF100K0000
VP-XF100K0000
J
J
J
J
J
J
Peaking 68µH
Peaking 10µH
Peaking 10µH
Peaking 10µH
Peaking 10µH
Peaking 10µH
AB
AB
AB
AB
AB
AB
CAPACITORS
AB
AB
AL
[EL.··· Electrolytic]
C1701 VCEA0A1HW475M J 4.7
50V
C1702 VCEA0A1HW475M J 4.7
50V
C1703 VCEA0A1HW475M J 4.7
50V
33
EL.
EL.
EL.
AB
AB
AB
27N-S300
CN27S30
Ref. No.
★
Part No.
Description
Code
Ref. No.
R1723
R1724
R1741
R1742
R1743
R1744
R1745
R1746
R1747
R1761
R1762
R1763
R1764
R1765
R1766
R1791
R1801
R1821
R1822
R1823
R1825
R1828
R1831
R1832
R1833
R1834
R1841
R1842
R1843
R1861
R1862
R1863
R1864
R1865
R1866
R1867
R1868
R1881
R1882
R1883
R1884
R1885
R1886
R1887
R1889
PWB-R: DUNTK9511WEK3
P-IN-P UNIT (Continued)
C1721
C1722
C1741
C1742
C1743
C1761
C1762
C1763
C1781
C1791
C1792
C1801
C1802
C1803
C1804
C1805
C1806
C1807
C1809
C1810
C1811
C1812
C1821
C1822
C1841
C1842
C1843
C1845
C1846
C1847
C1848
C1849
C1850
C1851
C1861
C1862
C1863
C1865
C1866
C1867
C1868
C1869
C1870
C1871
C1872
VCEA0A1HW106M
VCCCCY1HH330J
VCQYTA1HM473J
VCEA0A1HW105M
VCQYTA1HM472J
VCQYTA1HM473J
VCEA0A1HW105M
VCQYTA1HM682J
VCEA0A1CW476M
VCEA0A1AW107M
VCEA0A1AW107M
VCKYCY1CB104K
VCKYCY1HB103K
VCKYCY1HB103K
VCKYCY1HF103Z
VCEA0A1HW106M
VCKYCY1CB104K
VCKYCY1HB103K
VCKYCY1HB103K
VCEA0A1CW226M
VCKYCY1HF103Z
VCEA0A1HW106M
VCKYCY1HF103Z
VCEA0A1HW106M
VCEA0A1HW106M
VCKYCY1HF103Z
VCCCCY1HH680J
VCKYCY1HB103K
VCCCCY1HH151J
VCKYCY1HB103K
VCKYCY1CB104K
VCEA0A1HW106M
VCKYCY1CB104K
VCKYCY1HF103Z
VCKYCY1CB104K
VCKYCY1CB104K
VCCCCY1HH101J
VCFYFA1HA154J
VCQYTA1HM103J
VCKYCY1CB104K
VCFYFA1HA474J
VCKYCY1HF103Z
VCEA0A1HW106M
VCEA0A1HW106M
VCKYCY1HF103Z
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
10
33p
0.047
1
4700p
0.047
1
6800p
47
100
100
0.1
0.01
0.01
0.01
10
0.1
0.01
0.01
22
0.01
10
0.01
10
10
0.01
68p
0.01
150p
0.01
0.1
10
0.1
0.01
0.1
0.1
100p
0.15
0.01
0.1
0.47
0.01
10
10
0.01
50V
50V
50V
50V
50V
50V
50V
50V
16V
10V
10V
16V
50V
50V
50V
50V
16V
50V
50V
16V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
16V
50V
16V
50V
16V
16V
50V
50V
50V
16V
50V
50V
50V
50V
50V
EL.
Ceramic
Mylar
EL.
Mylar
Mylar
EL.
Mylar
EL.
EL.
EL.
Ceramic
Ceramic
Ceramic
Ceramic
EL.
Ceramic
Ceramic
Ceramic
EL.
Ceramic
EL.
Ceramic
EL.
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Mylar
Mylar
Ceramic
Mylar
Ceramic
EL.
EL.
Ceramic
AB
AA
AA
AB
AB
AA
AB
AB
AB
AB
AB
AB
AA
AA
AA
AB
AB
AA
AA
AB
AA
AB
AA
AB
AB
AA
AA
AA
AA
AA
AB
AB
AB
AA
AB
AB
AA
AC
AA
AB
AC
AA
AB
AB
AA
RJ1
RJ2
M-Ox.
Carbon
AA
AA
RJ3
RJ4
RJ5
RJ6
RJ7
RJ8
RJ9
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
AA
AA
AA
AA
AA
AA
AA
RJ10
RJ11
R1701
R1702
R1703
R1704
R1705
R1706
R1721
R1722
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
★
VRS-CY1JF822J
VRS-CY1JF222J
VRD-RA2BE102J
VRS-CY1JF102J
VRS-CY1JF151J
VRS-CY1JF122J
VRS-CY1JF474J
VRS-CY1JF122J
VRD-RA2BE822J
VRS-CY1JF102J
VRS-CY1JF151J
VRS-CY1JF102J
VRS-CY1JF122J
VRS-CY1JF474J
VRS-CY1JF122J
VRD-RA2BE151J
VRS-CY1JF473J
VRS-CY1JF123J
VRS-CY1JF103J
VRS-CY1JF183J
VRS-CY1JF183J
VRS-CY1JF153J
VRS-CY1JF332J
VRS-CY1JF682J
VRS-CY1JF272J
VRS-CY1JF222J
VRS-CY1JF153J
VRS-CY1JF471J
VRS-CY1JF391J
VRS-CY1JF153J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF221J
VRS-CY1JF474J
VRS-CY1JF104J
VRS-CY1JF202J
VRS-CY1JF510J
VRS-CY1JF473J
VRS-CY1JF223J
VRS-CY1JF123J
VRS-CY1JF101J
VRS-CY1JF473J
VRS-CY1JF223J
VRS-CY1JF123J
VRD-RA2BE101J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
8.2k
2.2k
1k
1k
150
1.2k
470k
1.2k
8.2k
1k
150
1k
1.2k
470k
1.2k
150
47k
12k
10k
18k
18k
15k
3.3k
6.8k
2.7k
2.2k
15k
470
390
15k
1k
1k
220
470k
100k
2k
51
47k
22k
12k
100
47k
22k
12k
100
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
MISCELLANEOUS PARTS
P1701 QPLGZ0810CEZZ
P1702 QPLGZ0610CEZZ
P1703 QPLGZ0810CEZZ
SLD1801 PSLDM0012MEFW
RESISTORS
[M-Ox.··· Metal Oxide]
VRS-CY1JF000J
J 0
1/16W
VRD-MN2BE000J J 0
1/8W
or
VRS-CY1JF000J
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF000J
J 0
1/16W
VRD-MN2BE000J J 0
1/8W
or
VRS-CY1JF000J
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF000J
J 0
1/16W
VRS-CY1JF101J
J 100 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF101J
J 100 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF101J
J 100 1/16W
VRS-CY1JF474J
J 470k 1/16W
VRS-CY1JF332J
J 3.3k 1/16W
VRS-CY1JF103J
J 10k 1/16W
Part No.
34
J
J
J
J
Plug 8-pin
Plug 6-pin
Plug 8-pin
Shield
AD
AB
AD
AD
27N-S300
CN27S30
Ref. No.
★
Part No.
Description
Code
Ref. No.
CCABA1327MES0
Not Available
GCOVA1033MEKA
HBDGB1009MESA
JBTN-1101MEKA
JBTN-1102MEKA
GCABB1131MEKA
M
–
M
M
M
M
M
★
Description
Code
MISCELLANEOUS PARTS
CABINET PARTS
1
1-1
1-2
1-3
1-4
1-5
2
Part No.
Front Cabinet Ass'y
Front Cabinet
Cover for R/C
Badge, "SHARP"
Button, Power, Vol-up/down
Button, Ch-up/down
Rear Cabinet
å
BF
—
AD
AD
AD
AD
AZ
ACC701 QACCD3065CESA
QCNW-0130MEZZ
QCNW-0134MEZZ
QCNW-0137MEZZ
QCNW-0166MEZZ
QCNW-0167MEZZ
SP1
VSP0080PBK98A
SP2
VSP0080PBK98A
M
M
M
M
M
M
M
M
AC Cord
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Speaker 8 ohm, (R)
Speaker 8 ohm, (L)
AN
AF
AE
AH
AD
AC
AG
AG
SUPPLIED ACCESORRIES
RRMCG1396CESA M Infrared R/C Unit
AW
TGAN-1006MEZZ M Guarantee Card (27N-S300) AA
TiNS-6921MEZZ
M Operation Manual
AD
(27N-S300)
TiNS-6969MEZZ
M Operation Manual
AD
(CN27S30)
CABINET PARTS LOCATION
PACKING PARTS
(NOT REPLACEMENT ITEM)
1 1-1
SPAKC0667MEZZ
SPAKC0671MEZZ
SPAKX0165MEZZ
SSAKA0004MEZZ
2
1-3
PI P
1-4
/M T
S
1-2
1-5
35
–
–
–
–
Packing Case (27N-S300)
Packing Case (CN27S30)
Buffer Material
Wrapping Sheet
—
—
—
—
27N-S300
CN27S30
Ref. No.
Part No.
★
Code
No.
Part No.
PACKING
OFRef.
THE
SET
Description
★
Description
Code
★ Polyethylene Bag
Operation Manual
Guarantee Card
Infrared R/C Unit
★ Batteries
★ Wrapping Sheet
★ Buffer Material
FRONT
★ Packing Case
Use tapes to
fix the packing case.
REAR
★ MARK : Not replacement items.
★ Bar Code Label
36
27N-S300
CN27S30
Ref. No.
Part No.
★
Description
Code
Ref. No.
37
Part No.
★
Description
Code
27N-S300
CN27S30
Ref. No.
Part No.
★
Description
Code
Ref. No.
★
Part No.
Description
Code
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
TQ0872-S
Apr. 2000 Printed in Japan
MI. DS
38