Mitsubishi Electric LT-2240 Service manual

2003-2004
MITSUBISHI ELECTRIC
Service
Manual
LIQUID CRYSTAL DISPLAY TELEVISION
LT-2220
LT-2240
LT-3020
LT-3040
LT-3050
CAUTION:
Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and
"PRODUCT SAFETY NOTICE" contained in this manual.
SPECIFICATIONS
• Power
• LCD Panel
• Analog Inputs
• Digital Input
• Audio Outputs
• Tuning
: NTSC 181Channel Analog Cable
: [LT-2220, LT-2240] AC ADAPTOR
In - AC 120V, 60Hz; Out - 20VDC 6.0A
: [LT-3020, LT-3040, LT-3050] 120V, 60Hz, 2.2A • Frequency Range : VHF 54 ~ 470MHz
UHF 470 ~ 806MHz
: Resolution - 1280X768
• Speakers
: [LT-2220, LT-2240]
: Pixel Pitch - [LT-2220, LT-2240] 0.375mm
Left & Right (2 X 2.3W) Sub (3.4W)
[LT-3020, LT-3040, LT-3050] 0.5025mm
: [LT-3020, LT-3040, LT-3050]
Left & Right (2 X 3.5W) Sub (6W)
: VHF/UHF 75Ω unbalanced
: Two A/V Inputs (Composite or S-Video)
• W e ight / Ca bine t Dim e nsions
L-R Audio
W ith S ta nd: He ight W idth De pth W e ight
: Two Component Video Inputs (480i/480p/
720p/1080i) L-R Audio
[LT-22XX] 20-1/4" 22-3/4" 11-7/8" 36.6 lbs
: PC Input - 60Hz (VGA,S-VGA,XGA,W-XGA)
[LT-30XX] 25-3/8" 29-3/4" 11-7/8" 54.3 lbs
: PC Audio - 3.5mm Mini-Jack
W /O S ta nd: He ight W idth De pth W e ight
[LT-22XX] 18-5/8" 22-3/4"
4"
19.8 lbs
: MonitorLink™/DVI (Video Sources Only)
[LT-30XX] 23-1/4" 29-3/4"
5"
37.5 lbs
L-R Audio (Analog)
: MonitorLink™ Control/RS-232C
: L-R Audio Output (Fixed/Variable)
: Headphone Jack (Variable) 3.5mm
• Weight and dimensions shown are approximate.
• Design specifications are subject to change without notice.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road, Irvine, CA 92618-1904
Copyright © 2004 Mitsubishi Digital Electronics America, Inc.
All Rights Reserved
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
CONTENTS
INTRODUCTION .................................................................................................................................. 5
PRODUCT SAFETY NOTICE ............................................................................................................... 5
SAFETY PRECAUTIONS ..................................................................................................................... 5
DISASSEMBLY
LT-22XX ............................................................................................................................................. 7
LT-30XX ........................................................................................................................................... 13
ELECTRICAL ADJUSTMENTS
Initial Setup .................................................................................................................................... 21
CIRCUIT EXPLANATIONS & BLOCK DIAGRAMS
Circuit Explanations ....................................................................................................................... 23
Block Diagrams .............................................................................................................................. 29
TEST POINT LOCATIONS AND DESCRIPTIONS
PWB-SET Test Point Locations and Description ............................................................................ 33
PWB-MAIN Test Point Locations and Description .......................................................................... 35
TROUBLESHOOTING
LT-22XX Power Troubleshooting ...................................................................................................... 37
LT-30XX Power Troubleshooting ...................................................................................................... 39
Video Troubleshooting .................................................................................................................... 41
Audio Troubleshooting .................................................................................................................... 51
Remote Control & Front Switch Troubleshooting ............................................................................ 53
REPLACEMENT PARTS
Replacement Parts List .................................................................................................................. 55
INTERCONNECT WIRING DIAGRAM
Page 3
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Page 4
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety related characteristics. These
characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be
obtained by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have special safety characteristics are identified in this service manual.
The replacement for any safety part should be identical in value and characteristics.
SAFETY PRECAUTIONS
NOTICE:
Observe all cautions and safety related notes located inside the receiver cabinet and on the
receiver chassis.
WARNING:
1.
2.
3.
Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard
from the receiver's power supplies. Work on the receiver should not be attempted by anyone who is
not thoroughly familiar with the precautions necessary when working on high voltage equipment.
Do not install, remove or handle the LCD panel in any manner unless shatterproof goggles are
worn. People not so equipped should be kept away while the panel is being handled. Keep
the panel away from the body while handling.
When service is required, observe the original lead dress. Where a short-circuit has occurred, replace
those components that indicate evidence of overheating.
Leakage current check
Before returning the receiver to the customer, leakage current should be measured using following methods.
1. Cold Check
With the alternating current (AC) plug removed from the AC source, place a jumper across the two AC plug
prongs. Connect one lead of an ohm meter to the AC plug and touch the other lead to each exposed metal part
(i.e. antennas, handle bracket, metal cabinet, screw heads, metal overlay, control shafts, etc.), particularly any
exposed metal part that has a return path to the chassis. The resistance of the exposed metal parts having a
return path to the chassis should be a minimum of 1Mega Ohm. Any resistance below this value indicates
an abnormal condition and requires corrective action.
2. Hot Check ...Use the circuit shown below to perform the hot check test.
1. Keep switch S1 open and connect the receiver to the measuring circuit. Immediately after
connection, and with the switching devices of the receiver in their operating positions, measure
the leakage current for both positions of switch S2.
2. Close switch S1, energizing the receiver. Immediately after closing switch S1, and with the
switching devices of the receiver in their operating positions, measure the leakage current for both
positions of switch S2. Repeat the current measurements of items 1 and 2 after the receiver has
reached thermal stabilization. The leakage current must not exceed 0.5 milliampere (mA).
Page 5
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Page 6
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-22XX)
Remove the screws and components in the quantities indicated.
Reassemble in reverse order.
1. COVER, REAR
2. STAND UNIT
Page 7
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-22XX) CONTINUED
3. BACK UNIT
4. BACK COVER
Page 8
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-22XX0) CONTINUED
5. PWB-SET
6. PWB-MAIN
Page 9
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-22XX) CONTINUED
7. CHASSIS BASE
Page 10
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-22XX) CONTINUED
8. LCD
9. PANEL
Page 11
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-22XX) CONTINUED
WIRING HARNESS LOCATIONS
Page 12
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX)
Remove the screws and components in the quantities indicated.
Reassemble in reverse order.
1. COVER, REAR
Page 13
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
2. STAND UNIT
3. BACK COVER
Page 14
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
4. UNIT SPEAKER
5. BRACKET, VESA
Page 15
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
6. SHIELD, POWER & SHIELD, CASE
7. COVER, TERMINAL, LEFT & RIGHT
Page 16
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
8. ASSY-PWB-MAIN/ASSY-PWB-SET/UNIT-POWER
Page 17
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
9. CHASSIS, REAR
Page 18
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
10. BRACKET T/B/LCD PANEL
11. BEZEL
Page 19
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
DISASSEMBLY PROCEDURE (LT-30XX) CONTINUED
WIRING HARNESS LOCATIONS
Page 20
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Initial Setup
A. Option Menu Setup
Follow the steps below for the initial set-up:
1. Select the "MENU" display by pressing the "MENU" button once.
2. Press the number buttons "2", "0", "7", "0" in sequence to select the "OPTION MENU" display.
3. Press the "ADJUSTpq" buttons to select "INITIAL."
4. Press "ENTER."
MENU-2-0-7-0
OPTION MENU
Initial
Power Restore
DTV Port
Direct Key Mode
:OFF
:Auto
:OFF
NOTE: At this time channel 3 is automatically selected and all Menu and Audio/Video user setting are set
to the defaults shown in the chart below.
B. Default Settings
MAIN MENU DEFAULT SETTINGS
SETUP
Memorize channels ANT-A - Air
Language (idioma)
English
Front Button Lock
Off
CLOCK
Clock Setting
Manual
Clock Time
-- :-- -Set Day
Sunday
CAPTIONS
Closed Captions
On if Mute
CC Background
Gray
CHANNEL EDIT
Antenna
ANT-A
Channel
3
Memory
Deleted
Name
N/A
SQV
N/A
V-CHIP-LOCK
V-Chip
Off
TV Rating
TV-PG
FV- Fantasy Violence
Allow
D-Sexual Dialog
Allow
L-Adult Language
Allow
S-Sexual Situations
Allow
V-Violence
Allow
Programs Not Rated
Allow
Movie Rating
PG
V-CHIP LOCK By Tim e
V-Chip Start Time
12:00AM
V-Chip Stop Time
12:00AM
Lock by Time
Off
Lock Time
N/A
Unlock Time
N/A
ADVANCED FEATURES
Video Mute
On
Black Enhancement
On
PC Power Save
On
TIMER
Timer
Off
Set Time
-- :-- -Set Day
Sunday
COLOR BALANCE
Auto Color Correction
Off
MANUAL COLOR ADJUST
Magenta
31
Red
31
Yellow
31
Green
31
Cyan
31
Blue
31
Page 21
AUDIO/VIDEO
TV Speakers (Internal)
Audio Output
AUDIO SETTINGS
Bass
Treble
Balance
Sub-Woofer Level
Surround
TV Listen To
Level Sound
VIDEO SETTINGS
Contrast
Brightness
Sharpness
Color
Tint
Color Temp
Video Noise
Film Mode (Auto)
Back Light
PC/DVI H-Position
PC/DVI V-Position
PC Video Clock
PC Fine Detail
PC H-Resolution
PC V-Resolution
On
Variable
31
31
31
31
Off
Stereo
Off
31
31
31
31
31
High
Standard
On
63
31
31
31
31
31
31
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Circuit Explanations
1. Video circuits
This section explains the video circuitry of models LT-2220/LT3020. Both models have almost the same
circuits. The explanation corresponds to the various inputs (PC, TV, VIDEO, Component, DVI).
The HD input has realized high definition with the resolution of WXGA.
(Refer to the LT-2220 / LT-3020 Video block diagram, for the flow of video signals.)
1-1. Video input circuit
1-1-1. PC Input video circuit
For PC input, video is inputted into IC400 of the signal processing IC via the following IC’s.
(A) IC2A3 : Analog-to-digital conversion IC (AD9883AKST-110 : Analog devices)
The video signal (R, G, B) of PC input is changed into a digital signal (8 bits each) from an analog
signal. Besides digital conversion, this IC has the functions below:
-
Contrast adjustment for PC
-
brightness adjustment for PC
This IC is controlled by register control of IC 2A3 via 3.3V IIC-bus.
(B) IC2A2 : Inverting IC with Schmidt trigger (74LCX14 : Fairchild)
Input IC for Horizontal and Vertical sync signals from the PC input.
In case of noise on the leading and trailing edges or low amplitude of the sync signals outputted from a
PC, it is necessary to modify the waveform.
Improper waveforms are corrected by this IC in the following manner.
-
Noise on the leading/trailing edge : Rise-time and fall-time is carried out early.
-
Waveform is noisy
: False triggering prevented by the Schmidt circuit.
-
Low Amplitude
: If voltage threshold is satisfied, it will output at 3.3V.
Since the IC is an inverter, it will let it pass twice and has united polarity.
1-1-2. Component and DVI Input circuit.
For Component and DVI inputs, video is inputted into IC400, signal processing IC, via the following IC’s.
(C)IC204 : Analog-switch IC (BA7657 : Rohm)
In this IC, one of the 2 component signal inputs (Y, Cb, Cr) is chosen by the select signal. Select
signal CTL is controlled by the MCU.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
(D)IC2J1 : TMDS receiver IC with HDCP (Sii907B : SiliconImage)
In this IC, the input signal is processed based on EIA-861A. Inputs from a TMDS-Interface are
converted into a RGB analog signal. HDCP and HDTV resolutions are supported.
When no DVI signal is input, it changes to standby mode automatically and power consumption is
lowered. The LCD panel specification is for input signals whose vertical sync signal is 60Hz. The
outputs of this IC include separate horizontal and vertical sync signals.
(E)IC201 : Analog-switch IC with LPF (SM5301A : NPC)
In this IC, the component signal (Y, Cb, Cr) from IC204 or DVI signal (R,G,B) from IC2J1 is chosen
by the select signal and outputted.
Select signal MUXSEL is controlled by the MCU.
(F) IC202 : Sync separate IC (LM1881M : National Semiconductor)
Used for Component input.
This IC separates the composite H and V sync signal from the composite video signal
The composite sync signal is sent to IC203 (Sync select IC).
(G) IC203 : Sync select IC (HD74LV157: Hitachi)
In this IC, the composite sync signal from IC202(for component) or Separate sync signal from
IC2J1(for DVI) is chosen by the select signal and outputted.
Select signal MUXSEL is controlled by the MCU.
The output from this IC is sent to IC400 (Signal processor IC) in order to remove the
vertical sync signal and output the separated horizontal sync signal. The horizontal sync signal is
then routed to IC205 (Analog-to-digital conversion IC).
(H) IC205 : Analog-to-digital conversion IC (AD9883AKST-110 : Analog devices)
The Component video (YCbCr / RGB) or DVI inut is converted into a digital signal (8 bits
each) from an analog signal. Besides digital conversion this IC performs the following:
-
Contrast adjustment for Component or DVI
-
brightness adjustment for Component or DVI
This IC is controlled by register control of IC 205 via 3.3V IIC-bus.
This IC’s output is sent to IC500.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
(I) IC500 : Interlace-to-Progressive conversion IC ( gm6015 : Genesis)
This IC performs the following functions to all input signals except the PC input.
-
Motion adaptive De-interlacer for SD (480i) signals.
-
Scaling
-
PIP / POP control for AV input combinations.
-
Color / tint control
-
3 dimension Noise reduction.
-
Adaptive Film mode
-
Sync Separation for Composite sync.(for component only)
A format change to the input signal is also made by this IC.
Control is performed in 5-line serial communication from the MCU.
1-1-3. VIDEO and TV input circuitry
For VIDEO and TV inputs, the signal is applied to IC400, signal processing IC, via the following ICs.
(J)IC701 : Analog-switch IC (CXA2089 : SONY)
In this IC, the composite signal (CVBS) from video1/2 input or composite signal (S-video) from
video1/2 input is chosen by register control of IC 701 via 5V IIC-bus.
(K)IC702 : Buffer IC with LPF ( MM1566AF : Mitsumi)
IC701 reduces the high frequency noise ingredient of the video signal.
(L)IC100 : Analog-switch IC (CXA2069 : SONY)
In this IC, the composite signal (CVBS / S-video) from the video1/2 inputs or the composite signal
(CVBS) from the TV input is selected by register control of IC 100 via 5V IIC-bus.
It is also selected and sent to IC300 for CCD use.
(M)IC601 : Digital decoder IC with 3D Y/C separation (uPC64011 : NEC)
This IC converts the analog video signal (S-VIDEO/CVBS) from IC100 into a digital signal.
Besides digital conversion this IC also has the following functions.
-
3 dimension Y/C separation for CVBS
-
Contrast adjustment.
-
Brightness adjustment.
-
FIELD signal generation.
-
PLL (Phase-Locked Loop) : referential clock generation.
-
Sync signal generation
This IC is controlled by register control of IC 601 via 3.3V IIC-bus.
This IC’s output is sent to IC400.
(The output format is YPbPr and WXGA. Thw Vertical frequency is 60Hz.)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
1-2. Signal processor circuit
(N)IC400 : Signal processor IC ( M66473FP : Mitsubishi)
This IC has the functions below.
-
Scaling for PC
-
PIP/POP control for PC and AV combination
-
Picture enhancement
-
Auto setup for PC
-
Colorsync function
-
Frequency measurement / distinction
-
Sync separation for component CS
-
Color space conversion ( YPbPr à RGB )
-
Gamma correction
This IC is controlled by register control of IC 400 via 5-lines serial communication.
This IC’s output is sent to IC4A0.
(The output format is RGB and WXGA, and Vertical frequency is 60Hz.)
(O)IC4A0 : OSD mixing IC ( M66617FP : Mitsubishi)
This IC combines the picture signal outputted from IC400, the OSD signal outputted from the
MCU and the signal detected by CCD.
V-CHIP function is also controlled by this IC.
This IC is controlled by register control of IC 4A0 via serial communication.
The IC’s output is sent to IC4A1.
1-3. Output signal circuit
(P)IC4A1 : LVDS transmitter IC ( THC63LVDM83R : Thine)
This IC converts 28bits of TTL/CMOS data into LVDS data stream.
In 28 bits, 24-bits digital video signal, horizontal sync signal, vertical sync signal, an enable
signal and a clock signal for the LCD panel are included.
A phase-locked transmit clock is transmitted in parallel with the data streams over a fifth LVDS link.
This IC’s output is sent to the LCD panel.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2. Audio circuits
The audio circuits and speaker system of LT-22XX/LT30XX basically have the same circuits, except the Vcc
applied to the audio amplifier is different.
The specifications are as follows.
-
High Power (LT-22XX : 8W ,LT-30XX: 12W)
-
2.1ch Sub woofer speaker system
-
Impedance : 8 +/-1.2 ohms ( LT-22XX / LT-30XX )
-
Compact and high performance sound enclosure box.
-
Minimization of vibration noise
Refer to the LT-22XX / LT-30XX Audio block diagram.
2-1 Audio input mixing circuits
The audio input block consist of 2 AV-SW, IC701(CXA2089) on SUB-PWB and IC100(CXA2069) on
MAIN-PWB. Audio inputs for VIDEO1 and VIDEO2 are connected to IC701. Other external audio Inputs
(Component1/2 and DVI and PC) are connected to IC100. Their output is connected to IC710 (Audio
Processor : MSP3440G ) of Scart1 / Scrat2 input port.
TV broadcasting audio(SIF) is also connected to IC710’s IF Input port. Input sources are selected by register
control of IC 701/IC100/IC710 via 5V IIC-bus.
2-2 Audio processor IC
MSP3440G is used as the main audio processor.
This IC’s functions are as follows.
-
De modulator (SAP/Stereo)
-
Sub-woofer output
-
Volume control
-
Tone control
-
Surround
-
L/R mixing
-
Audio line output
Both models have the following audio controls on the users menu: Bass, Treble, Balance, Surround, Listen
to, Level Sound, Sub Woofer, Audio Out Fixed/Variable.
Audio adjustment of all controls except volume is performed by this IC.
(Refer to the “Owner’s guide” for a full explanation of each control.)
2-3 Audio amplifiers and speakers
These models use 2pcs of 2-CH BTL type audio amplifier AN7522.
One piece is for main audio, and one more piece is for the sub-woofer.
Amplifier +B voltage and the input circuits are slightly different by model. ( Refer to table 1).
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Table 1: Amp supply voltage(+B)
AMPVCC(for main)
SAMPVCC(for Sub Woofer)
LT-22XX
7.5V
9V
LT-30XX
9V
12V
Volume control is controlled by fading Volume1 /Volume2 DC signal to the amplifier Pin(#9).
Although the audio signals outputted from amplifier is sent to the SPEAKER, between the amplifier and
SPEAKER is a headphone terminal. If a headphone is connected, the audio signal to SPEAKER will be
interrupted and the audio signal will be sent to the headphone terminal.
3. Power circuit
Refer the LT-2220 / LT-3020 Power circuit block for the following.
The LT-2220 power supply is supplied from an AC adapter.
The LT-3020 power supply is supplied from a power supply board.
The LT-2220 has one connector for the inverter connection, the LT-3020 has two connectors.
Except for that, the circuit composition of the power supply is almost the same.
There are power supplies that are “always on” and “ON/OFF” with a control signal, as follows.
Power source
signal
20V
24V
8.5V
A12V
A9V
A8V
AMPVCC
SAMPVCC
S5V
SW5V
A30V
S3.3V
4.5V
D3.3V
A3.3V
AD3.3V
D1.9V
D2.5V
1.5V
Voltage [V ]
20
24
8.5
12
9
8
“30 : 9
“22 :7.5
“30 : 12
“22 :9
5
5
30
3.3
4.5
3.3
3.3
3.3
1.9
2.5
1.5
“always on” or
“ON/OFF”
always on
ON/OFF
always on
ON/OFF
ON/OFF
always on
ON/OFF
Control
signal
ON_24V
Psave2
Psave2
Psave3
ON/OFF
Psave3
always on
ON/OFF
ON/OFF
always on
always on
ON/OFF
ON/OFF
always on
ON/OFF
ON/OFF
ON/OFF
Psave1
Psave1
Psave1
Psave1
Psave1
Psave1
Psave1
Note
“22 only
“30 only
“30 only
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
BLOCK DIAGRAM of LT-22XX/LT-30XX(except Power)
IC2A2
74LCX14
3.3V
PC_H,V
Component 1 L/R
Component 2 L/R
DVI AUDIO
J102
PC AUDIO
J103
5V IIC
24.576
MHz
L/R
CVBS/SY/SC
IC702
18.432
MHz
MM1566AF
BUFFER
Input 1
J703
Input 1
J704
Input 2
J701
AUDIO L/R
S-Video
AV SW
CXA2089
9V
add=90H
5V IIC
MSP3440
Audio
Processor
8V
5V
add=80H
Port 0
14.318
MHz
Sub
Woofer
Out
IC712
AMP
AN7522
IC711
AMP
AN7522
5BUS
IC501
64M
SDRAM
IC401
16M
SDRAM
PC_H,V
CCD_Main
CCD_Sub
MUXSEL
PWBSET(SUB)
MAIN
L/R Out
IC300
CPU M306V7
VRF/CTL
Psave 1/2/3
Reset/RSB
L
RESETQ
5V IIC
TU IIC
5V
3.3V
3.3V IIC
PC_DDC
R
Woofer
IC2A1
DDC_EEP
3.3V
IC305
OPAMP
LMV324
5V
Volume 1/2
IC8X0
RS322
ADM3311
3.3V
SW
LED
MonLink
LCD Panel
R,G,B
IC301
RESET M51957
3.3V
SW LR2
TV MPX
IC710
3.3V
2.5V
IC303
Head
Phone
J706
CVBS
SW LR1
IC701
LVDS
3.3V
64K EEP
3.3V
Audio
Out
J705
S-Video
IC601
16M
SDRAM
IC4A1
24bit
5V IIC
RESETQ
AUDIO L/R
Y,Cb/
Pb,Cr/Pr
OSD MIX
ENMA?
R,G,B
16MHz
Input 2
J702
Page 29
CVBS
CCIR601
H,V,DE,CLK
16bit
CXA2069
9V
add=92H
L/R
3D-I/P
PiP/PoP
3.3V
2.5V
H,V,DE,CLK
Field
3D-YC
DECODER
3.3V/1.5V
add=B8H
CVBS/Y/C
IC500
gm6015
24bit
3.3V
1.9V
PDWN
IC100
AV SW
IC4A0
M66617FP
SCALER
PiP/PoP
OSD-MIX
CCDSUB
URANUS
YUV/R,G,B
IC601
UPD64011
CCDMAIN
MPX
Conponent
AUDIO
J201
A/D
3.3V
add=9AH
H,V,DE,CLK
H,V,DE,CLK
H,V,CLK/RST
TV
COMPOSIT_H2
H,V,CLK
AD9883A
3.3V IIC
IC400
BUS
IC205
RESET/PSAVE1
TU IIC
SW
74LV157
3.3V
DVI H,V
DVI H,V
SYNC
IC203
Port 1
IC2J2
E-DDC
3.3V
SYNC
SYNC SEP
LM1881M
VRF
SW
SM5301
5V
Analog RGB
IC202
MUXSEL
IC201
Y for CCD2
DVI HD
(J2J0)
SiI907B
TMDS
HDCP
3.3V
SW
YPbPr/
BA7657 YCbCr
5V
R,G,B
RSTB
IC204
Conponent 2
(VIDEO)
A/D(PC)
3.3V
add=98H
CTL
IC490
20MHz
H,V,CLK
BUS
3.3V IIC
Conponent 1
(VIDEO)
IC2J1
TU1A0
TUNER
30V
5V
add=C0H
IC2A3
AD9883A
Analog RGB
3.3V IIC
PC_H,V
Component1
/2
J201
PC
J2A1
(Dsub15)
PC_DDC
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
POWER CIRCUIT BLOCK DIAGRAM
20V
"22 Only
Adaptor SEB150P2
5A
AC-Adaptor "22
Only
24V (1) "30 Only
PWB-POWER
ON_24V
24V (2) "30 Only
PWB-POWER
ON_24V
FOR LT-22XX / LT30XX
3A
(2.7A)
JP JP
"22 "22
OnlyOnly
PWB-SET(SUB)
"22: 3A "30: 2.8A (2.5A)
INVERTER
TO INVERTER
3.8A
(3.5A)
"30: 2.8A (2.5A)
INVERTER "30 Only
TO INVERTER
LCD PANEL
A12V IC860
PQ1CY1032Z
PSAVE2
"30: 0.9A
"22: 0.8A
A12V
TO MAIN
POWER-UNIT
A9V
IC8K0
BA178M09FP
"30 Only
0.15A
IC701 AV-SW CXA2089
A9V
IC100 AV-SW CXA2069
TC1A0 TUNER 115VF045AR
TO MAIN
"22 Only
A8V
IC8J0 0.015A
BA178M08FP
IC710 MPX MSP3440G
"30 Only
PWB-MAIN
8.5V
"30 Only
PWB-POWER
1.2A
AMPVCC IC870
PQ1CY1032Z
PSAVE3
SAMPVCCIC880
PQ1CY1032Z
PSAVE3
S5V
IC850
PQ1CY1032Z
"30: 9V
"22: 7.5V
1.4A
1.2A
IC712 MAIN AMP AN7522F
"30: 12V
"22: 9V
0.95A
0.6A
IC711 SUB AMP AN7522F
S5V
0.6A
IC300 MPU M306V7
IC2A1 EEPROM 24LC21TSW
TO MAIN
IC710 MPX MSP3440G
SW5V IC8E0
CPH6311
PSAVE1
0.4A
: Power source is
always ON
DEVICE IC : use several
power sources
IC702 MM 1556AF
IC305
IC201
IC204
TC1A0
IC202
A5V
TO MAIN
A30V IC180
LA7995M
S3.3V IC8F0
SI3033LSA
0.05A
0.005A TC1A0 TUNER 115VF045AR
IC8X0 ADM3311EARS
S3.3V
TO MAIN
4.5V
IC840
PQ1CY1032Z
1.2A
D3.3V IC8N0
SI3033LSA
PSAVE1
0.5A
D3.3V
TO MAIN
D1.9V IC402
SI3018KS
PSAVE1
A3.3V IC8M0
SI3033LSA
PSAVE1
AD3.3V IC8Y0
SI3033LSA
D2.5V IC830
PQ1CY1032Z
PSAVE1
0.8A
0.04A
0.27A
A3.3V
IC300
IC301
IC303
IC2A2
MPU M306V7
RESET IC M51957
EEPROM 24LC64T-I
74LCX14
IC400
IC500
IC501
IC401
IC602
IC601
IC4A0
IC4A1
IC4A4
IC4A2
IC490
Scaler Uranus M66473FP
3D I/P gm6015
DRAM64 K4S643232F-TC60
DRAM16 IC42S1600-7T *2
DRAM16 IC42S1600-7T *2
3D Y/C UPD64011
ENMA M66617FP
LVDS THC63LVDM83R
74LCX74MTCX
74LCX04MTCX
DSO751SV 20MHz
IC400 Scaler Uranus M66473FP
IC601 3D Y/C UPD64011
IC203 HD74LV157
TO MAIN
0.24A
LMV324MTX
AV-SW SM5301A
AV-SW BA7657F
TUNER 115VF045AR
LM1881MX
AD3.3V
IC205 A/D AD9883
IC2A3 A/D AD9883
IC2J1 DVI SiI907B
TO MAIN
D2.5V
IC500 3D I/P gm6015
IC4A0 ENMA2 M66617FP
TO MAIN
1.5V
IC600
SI3012KS
0.06A
IC601 3D Y/C UPD64011
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
PC& V i d e o B L OCK DI A GRA M f o r L T -2 2XX /L T -3 0XX
Vcc=A3.3V
IC202
DVI H/V
SYNC SEP
LM1881M
Vcc=D3.3V/1.9V
Composite H
IC203
HS_out
sync SW
74LV157
Composite Sync
Vcc=D3.3V/D2.5V
Vcc=AD3.3V
Input 2
J702
IC601
uPD64011
H/V/CLK/FIELD
-3D-YC
-DECODER
-Black level / contrast
CVBS/ control for TV /VIDEO
SVideo input
YUV 16
- Motion adaptive
De- interlacer
- PiP/PoP control for
AV input Combination
- Color / Tint adjustment
-3D Noise Reduction
-Scaler for AV Input
-Sync Separation for
Composite Sync
24
CCDMAIN
CCDSUB
S-Video
Analog
To
IC300
(M602V7)
RGB
24
WXGA60
WXGA60
Vcc=D3.3V
H/V/CLK
IC490
20MHz
Digital Circuit
IC4A1 LVDS Tx
24
- OSD MIX
WXGA60
480i
IC501
CVBS/
SVideo
24.576MHz
IC702
MM1566AF
BUFFER
CVBS
CXA2089
9V
S-Video
3.3V IIC
YCbCr/
YPbPr
RGB
OSD Mix
between
IC300
5V IIC
480i/480p/720p/1080i
H/V/CLK
Field
CPU Bus
Vcc=A9V
IC500
gm6015
24
Vcc=A3.3V/A1.5V/D1.5
Vcc=A9V
LPF
CVBS
IC701(AV SW)
Input 2
J701
YUV/RGB
TV
Vcc=A5V
Input 1
J704
Black level / contrast
control for
Component / DVI
9V
Input 1
J703
H/V/CLK
64M SDRAM
DVI HV
ADC(for COMP/DVI)
CPU Bus
IC2J1
SiI907B
- TMDS-Rx
- HDCP Dec
- DAC
IC100
AV SW( CXA2069 )
MONITORLINK
(J2J0)
TMDS
AV-SW
-LPF
Analog
RGB
IC205
AD9883A
YPbPr/
RGB
H/V/CLK
IC4A0
M66617FP
(ENMA II)
CPU Bus
IC201
3.3V IIC
Vcc=D3.3V
VRF
MUXSEL
YPbPr/
YCbCr
Vcc=D3.3V/D2.5V
14.318MHz
BA7657
AV-SW
Vcc=AD3.3V
- Scaler for PC
- PiP/PoP control for
PC and AV combination
- Picture Enhancement
- Auto Setup
- Colorsync adjustment
- Sync Separation
for component CS
- Gamma
IC401
Vcc=A5V
IC204
Composite H2
CTL
(URANUS)
VGA/SVGA/XGA/WXGA
3.3V IIC
Vcc=D3.3V
Conponent 2
Black level / contrast
control for PC
IC400
M66473FP
16M SDRAM
ADC(for PC)
IC601
Conponent 1
Vcc=A5V
24
16M SDRAM
YpbPr/
YCbCr
RGB
Port1
74LCX14
Analog RGB
Vcc=AD3.3V
TU1A0
TUNER
30V
5V
add=C0H
IC2A3
AD9883A
PC_H,V
Y for CCD2
PC
J2A1
(Dsub15)
Component1/2
J201
IC2A2
Port0
H/V/CLK
Vcc=S3.3V
PC_H,V
Vcc=D3.3V
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
A U DI O B l o c k Di a g r a m f o r L T -2 2XX /L T -3 0XX
PWB-SET(SUB)
PWB-MAIN
AMPVCC
SAMPVCC
Component 1
Audio
(J201)
Component 2
Audio
(J201)
IC710 MSP3440g
MAIN_L_P
IC100
Main Audio
Processor
Core
AV-SW
CXA2069
ADC
DVI-AUDIO
(J102)
PC-AUDIO
(J103)
-De modulator
-Volume
-Tone control
-Surround
-L/R-Mix
(for Woofer out)
- or others
MAIN Out
IC712
AN7522
MAIN_L_N
Speaker -L
MAIN_R_P
MAIN_R_N
Speaker -R
DAC
Woofer out
IC711
AN7522
SUB_P
Speaker Woofer
SUB_N
J706
Head
Phone
Jack
Input
source
Select
VIDEO 1
IC701
VIDEO 2
ADC
AV-SW
CXA2089
SUB
auduo
processor
DAC
Audio line output
J705
-Volume
MPX
from TU1A0
SIF output
Volume1
from
IC300
#24
3.3V
0V
+
-
Volume control for MAIN
Amp
0.02Vdc to 1.15Vdc
IC305
+
-
PWB-MAIN
Table: Supplied voltage to Amp +B
LT-2220
AMPVCC
SAMPVCC
Volume control for SUB Amp
LT-3020
7.5V
9V
9V
12V
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
TEST POINT LOCATIONS AND DESCRIPTIONS
Test points, locations and descriptions are shown below.
(1) PWB-SET (SUB)
1
2
3
Test Point
Pin1 of J800
F800
INV-SW
Location
J801(Fuse-clip)
J802(Fuse-clip)
Pin12 of J821
4
BRIGHT
Pin14 of J821
5
6
7
24V
8.5V
IN_24V
Pin4, 6 of J810
Pin2 of J810
Pin8 of J810
8
Psave1
Pin5 of J712
9
A8V
(+) of C733
10
AMPVCC
Pin1 of IC711
11
SAMPVCC
Pin1 of IC712
12
Psave2
Pin6 of J712
13
Psave3
Pin7 of J712
14
MPX
Pin8 of J710
15
SW_L
Pin10 of J710
16
SW_R
Pin12 of J710
17
5V_SDA
5 of J711
18
5V_SCL
6 of J711
19
MPX_RST
Pin10 of J711
20
F880
F880
21
F870
F870
Description
20Vdc from AC-ADAPTOR
20Vdc behind the fuse F800
Used to control inverter ON/OFF. (0V :
OFF , 5Vdc : ON)
Used for brightness control of
inverter. (PWM control)
(Max : 5Vdc, Min : thin pulse)
24Vdc from Power-unit.
8.5Vdc from Power-unit.
3.3Vdc.
Used for ON/OFF control of the power
supply from the POWER-UNIT.
ON/OFF control signal of D3.3V, A3.3A.
(0V : OFF , 3.3Vdc : ON)
8Vdc.
Used to supply power to IC710.
7~9Vdc.
Used to supply power to IC711.
8~12Vdc.
Used to supply power to IC712.
ON/OFF control signal of A9V, A8V
A5A. (0V : OFF , 3.3Vdc : ON)
ON/OFF control signal of AMPVCC,
SAMPVCC. (0V : OFF , 3.3Vdc : ON)
Analog video signal from TV input.
Voltage level is 1.0Vp-p (Typical)
Audio L signal for PC or Monitorlink or
Component input.
Audio R signal for PC or Monitorlink or
Component input.
Serial port data I/O for IC of 5V power
supply.
Serial port data clock for IC of 5V
power supply.
Reset signal of IC710.
(0V : reset)
7~9Vdc.
Power supply fuse for IC711.
8~12Vdc.
Power supply fuse for IC712.
Note
22inches only
22inches only
30inches only
30inches only
30inches only
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
J8T0
XH3
1
IC702
LPF
9
14
J711(PH- 14)
IC8X0
RS- 232C
IC860
DC
- DC
J705
Line Out
IC701
AV- SW
5 : 5V_SDA
6 : 5V_SCL
17
18
10 : MPX_RST
19
(+) of C733
IC710
SOUNDPRO
CESSOR
IC880
DC
- DC
J703
VIDEO2/ AUDIO2
Y
L
R
L
R
J706
HP
J8T1
XH3
PWB- SET(SUB)
1
13
1
J712(PH- 13)
12
4 : ON_24V
5 : Psave1
6 : Psave2
7 : Psave3
J710(PH- 12)
IC712(IC- AMP)
Radiator
IC870
DC
- DC
J701
VIDEO1/ AUDIO1
IC850
DC
- DC
20
8 : MPX
10 : SW_L
12 : SW_R
7
8
12
13
1
F800
8
5
6
IC711(IC- AMP)
2 : 8.5V
4 : 24V
6 : 24V
Radiator
21
12
12
16
1
1
1 of IC711
10
2
J802
1
16
J821(PH- 16)
12 : INV- SW
14 : BRIGHT
1
J820(PH- 15)
3
4
10
J715(PH6)
J8A0(XH10)
J810(
VH- 8P)
J8X0
RS232C
J801
1
11
F870
IC830
DC
- DC
J702
S1
IC840
DC
- DC
1 of IC712
J800
DC- IN
Y
L
R
J704
S2
F880
14
15
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
(2) PWB-MAIN
Test Point
Location
Description
1
S5V
Pin12 of J303
5Vdc(always on ).
Power supply voltage for MCU, etc.
2
S3.3V
Pin13 of J303
3.3Vdc(always on ).
Power supply voltage for MCU, etc.
3
D3.3V
Pin7 of J190
4
A5V
Pin1 of J190
3.3Vdc.
Power supply for IC300, IC4A0, IC4A1
etc.
5Vdc.
Power supply for IC204, IC201 etc.
5
A3.3V
Pin5 of J190
3.3Vdc.
Power supply for IC203, etc.
6
D2.5V
Pin8 of J190
7
AD3.3V
Pin6 of J190
8
D1.9V
L400
9
Digital_G7
14 of IC4A1
10
R4H6
R4H5
Vertical sync signal to LCD panel
R4H3
Clock signal to LCD panel
R4H4
Data_Enable signal to LCD panel
14
QHS
-27 of IC4A1
QVS
-28 of IC4A1
QCLK
-31 of IC4A1
QDE
-30 of IC4A1
A9V
2.5Vdc.
Power supply for IC500.
3.3Vdc.
Power supply for IC2A3, IC205, IC2J1,
etc.
1.9Vdc.
Power supply for IC500.
3.3Vdc.
MSB of green digital video signal to
LCD panel.
Horizontal sync signal to LCD panel
10 of J190
15
30V
Pin7 of IC180
16
Pin3 of IC600
17
18
19
A1.5V,
D1.5V
TU_SDA
TU_SCL
S3.3V(RMC)
Pin31 of IC300
Pin28 of IC300
Pin1 of J301
20
RMC
Pin2 of J301
21
KEY1
Pin4 of J301
22
KEY2
Pin5 of J301
23
V_OUT
Pin2 of J110
24
SY_OUT
Pin4 of J110
9Vdc.
Power supply for IC100.
30Vdc.
Power supply for TU1A0.
1.5Vdc.
Power supply for IC601.
Serial port data I/O for TU1A0.
Serial port data clock forTU1A0.
3.3Vdc(always on ).
Power supply for IR receiver and front
switches, etc.
Data signal from IR receiver.
This data is sent to MCU.
Data signal from front switch.
This data is sent to MCU.
Data signal from front switch.
This data is sent to MCU.
Analog video signal from VIDEO 1&2
inputs. (Composite video)
Analog video signal from VIDEO 1&2
inputs. (S-video)
11
12
13
Page 35
Note
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
PWB- MAIN
1
2
IC303
EEP
IC402
3018
IC400
GRAPHIC
& SCALER
J102
MONITOR
- LINK
- AUDIO
IC201
VIDEO- SW
IC490
20M
IC501
SDRAM64
14.318M
IC601
DECODER
wit h 3D- Y/ C
3 of IC600
IC180
LA7995
9
15
7 of IC180
TUNER
J190(XH- 10)
IC100
AV- SW
J110(PH- 12)
IC602
SDRAM16
1
16
IC600
3012
24.576M
IC203
157
IC205
A/ D- C
1
J301(PH- 9)
1 : S3.3V(RMC)
2 : RMC
4 : KEY1
5 : KEY2
19
20
21
22
IC2A1
EEP
IC202
1881
IC2A3
A/ D- C
IC2J2
EEP
IC2J1
TMDS- Rx
IC2A2
14
IC500
3D- I/ P
gm6015
2 : V_OUT
4 : SY_OUT
23
24
1 : A5V
5 : A3.3V
6 : AD3.3V
7 : D3.3V
8 : D2.5V
10 : A9V
4
5
7
3
6
14
J180
20
R
L
Pr
8
L400 (D1.9V)
Pb
IC401
SDRAM16
Y
IC4A0
IC- OSD
IC300
MCU
9
J101
COMPONENTAUDIO(1and2)
14 of IC4A1
J103
PC- AUDIO
L/ R
31 of IC300
16MHz
J201
COMPONENT(1and2)
10 13
17
J2J0
MONITOR- LINK
IC4A1
LVDS- Tx
J302
MCUWR
J2A1
PC(D- sub)
IC4A4 IC4A2
74
04
11 12
R4H6
R4H4 R4H5
R4H3
IC305
LM324
IC4A3
08
J4A0
J300(PH- 13)
IC204
VIDEO- SW
J303(PH- 14)
28 of IC300
18
IC301
RST
12 : S5V
13 : S3.3V
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
1. Power failure
1.1 In case of LT-22XX
(1)POWER is turned off.
Connect the Power plug and turn on the main Power switch (Front switch or remote control).
Is the POWER LED lit?
YES
NO
Is the power plug connected
NO
Poor power plug connection.
to the wall outlet correctly?
YES
· To “Flashing in green”(2)
· To “Flashing in amber”(3)
NO
Is all harness connected
correctly?
All harness connects
correctly.
YES
Is the 20V DC available before
NO
The AC-ADAPTOR is out of
order.
the fuse F800?
(Observing point : J801)
* Voltage range of 20V :18~21V
YES
NO
Is 20V DC available behind
Fuse F800 have blown out. If
the fuse F800?
the fuse are replaced and it
(Observing point : J802)
blows out again, the AC-
* Voltage range of 20V :18~21V
ADAPTOR is out of order.
YES
Is the S5V and S3.3V, AD3.3V output
NO
Power supply circuit
available at Pin12(S5V) and Pin13
which generates S5V
(S3.3V) of J303 and at Pin6 of J190
and S3V and AD3.3V in
(PH connector)?
the PWB-SUB(SET) is
S5V
S3.3V
AD3.3V
CN
J303
J303
J190
Pin No.
12
13
6
YES
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
Voltage
5Vdc
3.3Vdc
3.3Vdc
out of order.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
(2)Flashing in green.
Is the back-light on?
NO
Is the following harness connected?
NO
Poor harness connection.
-Between PWB-SUB(SET) and
INVERTER (J821-INVERTER)
-Between back-lights and
INVERTER
YES
Is the INV-SW output 5V-level
NO
at Pin12 of the J821 connector?
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
(PH connector)
YES
Is the BRIGHT output about 5V
level at Pin14 of the J821
connector? (PH connector)
YES
Inverter or back-light of LCDpanel are out of order.
YES
Skip to “2. No picture
displayed and picture
errors.”
(3)Flashing in Amber.
If POWER switch is
NO
pushed, does LED
become green?
YES
Skip to the above-mentioned
“(2) Flashing in green” .
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
NO
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
1.2 In case of LT-30XX
(1)POWER is turned off.
Connect the Power plug and turn on the main Power switch (Front switch or remote switch).
Is the POWER LED lit?
YES
NO
Is the power plug connected
NO
Poor power plug connection.
to the wall outlet correctly?
YES
· To “Flashing in green”(2)
· To “Flashing in amber”(3)
Is all harness connected
All harness connects
correctly?
correctly.
YES
NO
Is the 24V and 8.5V output
Is the IN_24V output
available at Pin2(8.5V) and
3Vdc at Pin8(24V) of the J810
Pins 4, 6(24V) of the J810
connector? (VH connector)
connector? (VH connector)?
If not outputting, IC300 or its
8.5V
24V
Pin No.
2
4, 6
Periphral circuits is out of
Voltage
8.5Vdc
24Vdc
order.(PWB-MAIN)
If outputting, Power unit is
* Voltage range of 8.5V :8.1~8.8V
out of order.
* Voltage range of 24V :22~26V
YES
Is the S5V and S3.3V, AD3.3V output
NO
Power supply circuit
available at Pin12(S5V) and Pin13
which generates S5V
(S3.3V) of J303 and at Pin6 of J190
and S3V and AD3.3V in
(PH connector)?
the PWB-SUB(SET) is
S5V
S3.3V
AD3.3V
CN
J303
J303
J190
Pin No.
12
13
6
Voltage
5Vdc
3.3Vdc
3.3Vdc
YES
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
out of order.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
(2)Flashing in green.
Is the back-light on?
NO
YES
Is the following two harness
NO
Poor harness connection.
connected?
-Between PWB-SUB(SET) and
INVERTER (J821-INVERTER)
(J820-INVERTER)
-Between back-lights and
INVERTER
YES
Is the INV-SW output 5V-level
NO
at each Pin12 of the J821 and
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
J820 connector? (PH connector)
YES
Is the BRIGHT output about 12V
level at each Pin14 of the J821
and J820 connector?
(PH connector)
* Voltage range : 10~14V
YES
Inverter or back-light of LCDpanel are out of order.
Skip to “2. No picture
displayed and picture
errors.”
(3)Flashing in Amber.
If POWER switch is
NO
pushed, does LED
become green?
YES
Skip to the above-mentioned
“(2) Flashing in green” .
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
NO
IC300 and peripheral circuits
are out of order.(PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2. No picture displayed and picture errors (It applies both LT-30XX and LT-22XX)
Note ) It applies when there is no screen display or an unusual screen is outputted, although
power supply is turned on and the back light is turned on.
Before checking, perform the initial setup. (Input before the initial setup is channel 3 of TV.)
* Input source changes in following order with DEVICE UP button of remote control or
DEVICE
button of front switch.
TV
Component1
Component2
DVI
Input1
Input2
PC
2-1. No picture displayed and picture errors of PC signal.
Enter an input of WXGA(60Hz) gray scale
0.7Vp-p
in D-sub connector(J2A1), and select PC INPUT.
(Push the device UP button 5 times.)
And then, perform AV reset by front switch.
The video level inputs above 0.7Vp-p.
Is all harness connected correctly?
(especially between PWB-MAIN
NO
Poor harness connection or
defective cable.
and LCD PANEL (J4A0-LCD))
YES
Is OSD available?
YES
NO
Problem is in IC300 or IC4A0 or IC4A1
Problem is in the following
(and peripheral circuits). Are the
circuit (and peripheral
specified voltages available at the
circuits) .
Voltage with
problem
connectors below?
CN
Pin No.
Name
S5V
J303
12
S3.3V
J303
13
D3.3V
J190
7
Psave1*
J712
5
* control signal of D3.3V
YES
2-1-1 (P*)
NO
2-1-2 (P*)
Voltage
5Vdc
3.3Vdc
3.3Vdc
3.3Vdc
S5V
S3.3V
D3.3V
Psave1
PWB
including
the circuit
in problem
SET(SUB)
SET(SUB)
SET(SUB)
MAIN
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-1-1 (P*)
2-1-2 (P*)
Is the digital video signal available at pin 14(G_7)
NO
IC300 or IC4A0 (and
of IC4A1, and control signals of 3Vp-p available at
peripheral circuits) are
pins 27(HS : R4H6) and 28(VS : R4H5) and
out of order. (PWB-
31(CLK : R4H3) and 30(DE : R4H4) of IC4A1 ?
MAIN)
14 of IC4A1
(MSB of Green)
3Vp-p
27 of IC4A1
(f=48KHz)
28 of IC4A1
(f=60Hz)
H
3Vp-p
V
3Vp-p
31 of IC4A1
(f=70MHz)
3Vp-p
30 of IC4A1
(f=48KHz)
3Vp-p
YES
LCD-module or IC4A1(PWB-MAIN) are out of
order.
NO
Problem is in IC2A3 or IC400
When the shown voltage is in
(and peripheral circuits). Are the
problem, PWB including the power
specified voltages available at the
supply circuit(and peripheral
connectors below?
CN
Name
AD3.3V
J190
D1.9V
L400
circuits) is the following.
Voltage with
PWB including
problem
the circuit in
problem
AD3.3V
SET(SUB)
D1.9V
MAIN
Pin No.
Voltage
6
-
3.3Vdc
1.9Vdc
YES
IC2A3 or IC400 (and peripheral circuits) are out
of order.(PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-2. No picture displayed and picture errors of Component signal.
Enter an input of D1(480i) gray scale in J201
connector, and select COMPONENT1 (or2) INPUT.
(Push the device UP button once.: twice in the case
1.0Vp-p
of COMPONENT2)
And then, perform AV reset by front switch.
The video level inputs about 1.0Vp-p.
Is all harness connected correctly?
NO
Poor harness connection or
defective cable.
(especially between PWB-MAIN
and LCD PANEL (J4A0-LCD))
YES
Is OSD available?
YES
NO
Problem is in IC300 or IC4A0 or IC4A1
NO
Problem is in the following
(and peripheral circuits). Are the
circuit (and peripheral
specified voltages available at the
circuits) .
Voltage with
problem
connectors below?
CN
Pin No.
Name
S5V
J303
12
S3.3V
J303
13
D3.3V
J190
7
Psave1*
J712
5
*control signal of D3.3V
YES
Voltage
5Vdc
3.3Vdc
3.3Vdc
3.3Vdc
Is the digital video signal available at pin 14(G_7)
S5V
S3.3V
D3.3V
Psave1
NO
PWB
including
the circuit
in problem
SET(SUB)
SET(SUB)
SET(SUB)
MAIN
IC300 or IC4A0 (and
of IC4A1, and control signals of 3Vp-p available at
peripheral circuits) are
pins 27(HS : R4H6) and 28(VS : R4H5) and
out of order. (PWB-
31(CLK : R4H3) and 30(DE : R4H4) of IC4A1 ?
MAIN)
14 of IC4A1
(MSB of Green)
3Vp-p
27 of IC4A1
(f=48KHz)
28 of IC4A1
(f=60Hz)
H
V
3Vp-p
3Vp-p
31 of IC4A1
(f=70MHz)
3Vp-p
30 of IC4A1
(f=48KHz)
YES
3Vp-p
LCD-module or IC4A1
(PWB-MAIN) are out of
order.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-2-1(P*)
2-2-1 (P*)
NO
Problem is in IC204 or IC201 or IC205 or
When the shown voltage is in
IC500 or IC400 (and peripheral circuits).
problem, PWB including the power
Are the specified voltages available at the
supply circuit(and peripheral
connectors below?
CN
Name
A5V
J190
A3.3V
J190
D2.5V
J190
D1.9V
L400
AD3.3V
J190
YES
circuits) is the following.
Voltage with PWB including
problem
the circuit in
problem
A5V
SET(SUB)
A3.3V
SET(SUB)
D2.5V
SET(SUB)
D1.9V
MAIN
AD3.3V
SET(SUB)
Pin No.
Voltage
1
5
8
6
5Vdc
3.3Vdc
2.5Vdc
1.9Vdc
3.3Vdc
IC204 or IC201 orIC205 or IC500 or IC400 (and
peripheral circuits) are out of order.(PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-3. No picture displayed and picture errors of DVI signal.
Enter an input of D2(480p) gray scale
in J2J0 connector, and select DVI INPUT.
(Push the device UP button 6 times)
0.7Vp-p
And then, perform AV reset by front switch.
The video level inputs above 0.7Vp-p.
Is all harness connected correctly?
NO
(especially between PWB-MAIN
Poor harness connection or
defective cable.
and LCD PANEL (J4A0-LCD))
YES
Is OSD available?
YES
NO
Problem is in IC300 or IC4A0 or IC4A1
NO
Problem is in the following
(and peripheral circuits). Are the
circuit (and peripheral
specified voltages available at the
circuits) .
Voltage with
problem
connectors below?
CN
Pin No.
Name
S5V
J303
12
S3.3V
J303
13
D3.3V
J190
7
Psave1*
J712
5
*control signal of D3.3V
YES
Voltage
5Vdc
3.3Vdc
3.3Vdc
3.3Vdc
Is the digital video signal available at pin 14(G_7)
S5V
S3.3V
D3.3V
Psave1
NO
PWB
including
the circuit
in problem
SET(SUB)
SET(SUB)
SET(SUB)
MAIN
IC300 or IC4A0 (and
of IC4A1, and control signals of 3Vp-p available at
peripheral circuits) are
pins 27(HS : R4H6) and 28(VS : R4H5) and
out of order. (PWB-
31(CLK : R4H3) and 30(DE : R4H4) of IC4A1 ?
MAIN)
14 of IC4A1
(MSB of Green)
3Vp-p
27 of IC4A1
(f=48KHz)
28 of IC4A1
(f=60Hz)
H
V
3Vp-p
3Vp-p
31 of IC4A1
(f=70MHz)
3Vp-p
YES LCD-module or IC4A1
30 of IC4A1
3Vp-p
(PWB-MAIN) are out of
order.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-3-1 (P*)
(f=48KHz)
2-3-1 (P*)
Problem is in IC2J1 or IC201 or IC205 or
NO
When the shown voltage is in
IC500 or IC400 (and peripheral circuits).
problem, PWB including the power
Are the specified voltages available at the
supply circuit(and peripheral
connectors below?
CN
Name
A5V
J190
A3.3V
J190
D2.5V
J190
D1.9V
L400
AD3.3V
J190
YES
circuits) is the following.
Voltage with PWB including
problem
the circuit in
problem
A5V
SET(SUB)
A3.3V
SET(SUB)
D2.5V
SET(SUB)
D1.9V
MAIN
AD3.3V
SET(SUB)
Pin No.
Voltage
1
5
8
6
5Vdc
3.3Vdc
2.5Vdc
1.9Vdc
3.3Vdc
IC2J1 or IC201 or IC205 or IC500 or IC400(and
peripheral circuits) are out of order. (PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-4. No picture displayed and picture errors of VIDEO signal.
Enter an input of NTSC gray scale
in J2J0 connector, and select VIDEO1 (or 2) INPUT.
(Push the device UP button 3 times :
1.0Vp-p
4 times in case of VIDEO2)
And then, perform AV reset by front switch.
The video level inputs about 1.0Vp-p.
Is all harness connected correctly?
NO
(especially between PWB-MAIN
Poor harness connection or
defective cable.
and LCD PANEL (J4A0-LCD))
YES
Is OSD available?
YES
NO
Problem is in IC300 or IC4A0 or IC4A1
NO
Problem is in the following
(and peripheral circuits). Are the
circuit (and peripheral
specified voltages available at the
circuits) .
Voltage with
problem
connectors below?
CN
Pin No.
Name
S5V
J303
12
S3.3V
J303
13
D3.3V
J190
7
Psave1*
J712
5
*control signal of D3.3V
YES
Voltage
5Vdc
3.3Vdc
3.3Vdc
3.3Vdc
S5V
S3.3V
D3.3V
Psave1
PWB
including
the circuit
in problem
SET(SUB)
SET(SUB)
SET(SUB)
MAIN
Is the digital video signal available at pin 14(G_7)
IC300 or IC4A0 (and
of IC4A1, and control signals of 3Vp-p available at
peripheral circuits) are
pins 27(HS : R4H6) and 28(VS : R4H5) and
out of order. (PWB-
31(CLK : R4H3) and 30(DE : R4H4) of IC4A1 ?
MAIN)
14 of IC4A1
(MSB of Green)
3Vp-p
27 of IC4A1
(f=48KHz)
28 of IC4A1
(f=60Hz)
H
V
3Vp-p
3Vp-p
31 of IC4A1
(f=70MHz)
3Vp-p
YES LCD-module or IC4A1
30 of IC4A1
3Vp-p
(PWB-MAIN) are out of
order.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-4-1 (P*)
(f=48KHz)
2-4-1 (P*)
YES
NO
Problem is in IC100 or IC601 or IC500 or
When the shown voltage is in
IC400 (and peripheral circuits).
problem, PWB including the power
Are the specified voltages available at the
supply circuit (and peripheral
connectors below?
CN
Name
A9V
J190
A1.5V
IC600
D1.5V
IC600
A3.3V
J190
D2.5V
J190
D1.9V
L400
AD3.3V
J190
YES
circuits) is the following.
Pin No.
Voltage
10
3
3
5
8
6
9Vdc
1.5Vdc
1.5Vdc
3.3Vdc
2.5Vdc
1.9Vdc
3.3Vdc
Voltage
with
problem
A9V
A1.5V
D1.5V
A3.3V
D2.5V
D1.9V
AD3.3V
Is the signal of 1.0Vp-p available at pin 2(V_out)
of J110,or pin 4 (SY_out) of J110?
Pin2 of J110
Pin4 of J110
IC701 or IC702 (PWBSET(SUB)) are out of order.
1.0Vp-p
YES
IC100 or IC601 or IC500 or IC400(and peripheral
circuits) are out of order.(PWB-MAIN)
NO
PWB including
the circuit in
problem
SET(SUB)
MAIN
MAIN
SET(SUB)
SET(SUB)
MAIN
SET(SUB)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
2-5. No picture displayed and picture errors of TV signal.
Enter an input of NTSC gray scale
in TU1A0 (TUNER), and select TV INPUT.
(It may not push the device button after initial
1.0Vp-p
setup. Adjust the channel of TV with the
channel of a signal source.)
And then, perform AV reset by front switch.
Is all harness connected correctly?
NO
Poor harness connection or
defective cable.
(especially between PWB-MAIN
and LCD PANEL (J4A0-LCD))
YES
Is OSD available?
YES
NO
Problem is in IC300 or IC4A0 or IC4A1
NO
Problem is in the following
(and peripheral circuits). Are the
circuit (and peripheral
specified voltages available at the
circuits) .
Voltage with
problem
connectors below?
S5V
S3.3V
D3.3V
Psave1*
CN
Name
J303
J303
J190
J712
Pin No.
Voltage
12
13
7
5
5Vdc
3.3Vdc
3.3Vdc
3.3Vdc
S5V
S3.3V
D3.3V
Psave1
PWB
including
the circuit
in problem
SET(SUB)
SET(SUB)
SET(SUB)
MAIN
YES
Is the digital video signal available at pin 14(G_7)
IC300 or IC4A0 (and
of IC4A1, and control signals of 3Vp-p available at
peripheral circuits) are
pins 27(HS : R4H6) and 28(VS : R4H5) and
out of order. (PWB-
31(CLK : R4H3) and 30(DE : R4H4) of IC4A1 ?
MAIN)
14 of IC4A1
(MSB of Green)
3Vp-p
27 of IC4A1
(f=48KHz)
28 of IC4A1
(f=60Hz)
H
V
3Vp-p
3Vp-p
31 of IC4A1
(f=70MHz)
30 of IC4A1
(f=48KHz)
3Vp-p
YES LCD-module or IC4A1
(PWB-MAIN) are out of
order.
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
3Vp-p
2-5-1 (P*)
2-5-1 (P*)
Problem is in IC100 or IC601 or IC500 or
NO
When the shown voltage is in
IC400 (and peripheral circuits).
problem, PWB including the power
Are the specified voltages available at the
supply circuit (and peripheral
connectors below?
CN
Name
30V
IC180
A9V
J190
A1.5V
IC600
D1.5V
IC600
A3.3V
J190
D2.5V
J190
D1.9V
L400
AD3.3V
J190
YES
circuits) is the following.
Voltage with PWB including
problem
the circuit in
problem
30V
MAIN
A9V
SET(SUB)
A1.5V
MAIN
D1.5V
MAIN
A3.3V
SET(SUB)
D2.5V
SET(SUB)
D1.9V
MAIN
AD3.3V
SET(SUB)
Pin No.
Voltage
7
10
3
3
5
8
6
30Vdc
9Vdc
1.5Vdc
1.5Vdc
3.3Vdc
2.5Vdc
1.9Vdc
3.3Vdc
TU1A0 or IC100 or IC601 or IC500 or IC400 (and
peripheral circuits) are out of order. (PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
3. No audio output generated.(It applies both LT-30XX and LT-22XX)
Notes) This model is enabled to set up an audio input terminal for each video input terminal. No
audio output is available unless the input terminal of displayed pictures (example:VIDEO1)
coincides with that of audio (example:PC). Therefore, analysis for troubleshooting should be
carried out after the displayed video input terminal (example:VIDEO1) has been made to coincide
with the input terminal according to the instruction manual.
Enter a signal input AUDIO in.
Volume level is not 0. And MUTE is off.
NO
Raise volume level. And MUTE is turned off.
YES
NO
Is “TV speakers” setting on?
“TV speakers” setting is on.
YES
In case of TV input, is “Listen To:” setting set
NO
to Stereo or Mono?
“Listen To :” setting is set to Stereo
or Mono.
YES
Is voltage the same before and behind F870
NO
It replaces the PWB-SET(SUB).
(Fuse have blown out. )
and F880?
YES
Are the specified voltages available at the
pins below? (Power source check)
CN
Pin No.
Name
S5V
J303
12
A5V
J8A0
1
A9V
J8A0
10
A8V
C733
AMPVCC
IC711
1
SAMPVCC
IC712
1
Psave2*
Psave3**
J712
J712
6
7
Problem is in the following
circuit (and peripheral
Voltage
5Vdc
5Vdc
9Vdc
8Vdc
7~9Vdc
8~12V
dc
3Vdc
3Vdc
*control signal of A9V, A8V, A5V
** control signal of AMPVCC, SAMPVCC
YES
NO
circuits) .
Voltage with
problem
S5V
A5V
A9V
A8V
AMPVCC
SAMPVCC
Psave2
Psave3
PWB
including
the circuit
in problem
SET(SUB)
SET(SUB)
SET(SUB)
SET(SUB)
SET(SUB)
SET(SUB)
MAIN
MAIN
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
3-A (P*)
3-A (P*)
YES
Is the signal below available at pins 5, 6 of
NO
J711 (control signals of IC701 and IC710 and
IC300 (and peripheral circuits)
are out of order.(PWB-MAIN)
IC100 ) and 10 of J711 (control signals of
IC710) and 28, 31 of IC300 (control signals of
TU1A0) ?
5, 6 of J711,
v
3Vp-p
28, 31 of IC300
10 of J711
3Vdc
YES
Is sound signal outputted correctly at the
pins 10, 12 ,8 of J710 connector?
? It checks that a certain signal is outputting
in the voltage range of 1V.
YES
IC701 and IC710 and IC711 and IC712 (and
peripheral circuits) are out of order.
(PWB-MAIN)
NO
IC100 (and peripheral circuits)
are out of order.(PWB- SET(SUB))
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
4. Other faults.(It applies both LT-30XX and LT-22XX)
Notes) It considers the case where there are problems except 1, 2, 3.
4-1. Remote control is not effective.
After checking the polarity of batteries, has
NO
Load the batteries, making sure the
polarities (-) and (+) are correct.
it loaded correctly?
YES
Regarding as the slide switch at the top of
NO
It sets the slide switch as “TV”.
the remote, does it set as “TV”?
YES
NO
Does it use within 20 feet?
YES
It does not operate, even if it exchanges for
NO
it uses within 20 feet.
It exchanges on new batteries.
new batteries.
YES
When it pushes the remote switch, is the
NO
signal below available at pins 1, 2, of J301
PWB (and peripheral circuits).
Pin with
PWB
problem
including
the circuit
in problem
2 of J301
CONT
1 of J301
MAIN
(remote switch use) ?
2:
3Vp-p
1
3Vdc
Problem is in the following
YES
Skip to “4-2 front switch is not effective”.
4-2. Front switch is not effective.
Is the following harness connected correctly?
NO
Poor harness connection or
defective cable.
· Between PWB-MAIN and PWB-CONT
(J301-J0A1)
YES
When it pushes the front switch, is the signal
below available at pins 1, 4, 5 of J301
(remote control and front switch use) ?
4, 5 :
3Vp-p only when switch is not pushed.
0V only when switch is pushed.
1
3Vdc
NO
Problem is in the following
PWB (and peripheral circuits).
Pin with
PWB
problem
including
the circuit
in problem
4, 5 of J301
CONT
1 of J301
MAIN
YES
IC300 (and peripheral circuits) are out of order.(PWB-MAIN)
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Part Number
7A930032
25327981
08LA10AE
25327921
25327971
7A081023
25435861
25435911
25435851
25435881
25435871
3A684043
3A681009
PWB-CONTROL LT2220
8BL61M12
PWB-SUB LT2220
PWB-TUNER LT2220
7A930037
3A290003
7A930033
25261691
7A930029
7A930030
LT-2220 PARTS LIST
Description
AC-ADAPTER (SEB150P2-20.0B)
BACK-UNIT (CABINET-BACK LT2220/2240)
BEZEL (INCLUDES INNER BEZEL & PLATE)
BEZEL-INNER (LC-T2220)
BEZEL-UNIT (LC-T2220 GRY)
CORD-POWER (1.9M 2P BLK)
COVER-LEFT
COVER-REAR (CLEAR)
COVER-RIGHT
COVER-TERMINAL LEFT
COVER-TERMINAL RIGHT
LCD (AA220TA01) T/A REQUIRED
LED (SML78420C)
PWB-CONTROL/LED T/A REQUIRED
PWB-MAIN (LT-2220) T/A REQUIRED
PWB-SUB T/A REQUIRED
PWB-TUNER T/A REQUIRED
REMOTE(EUR7616Z20/Z2A)
REMOTE-RECEIVER (GP1UD263XK)
SPEAKER-UNIT(ST-220-1)
STAND-UNIT (GREY)
TUNER (115V VF045AR)
UNIT-INVERTER (J191007.00)
Part Number
7A930032
25327981
08LA10AE
25327973
79PQ6640
25435861
25435911
25435851
25435881
25435871
3A684064
3A681009
PWB-CONTROL LT2240
8BL63M15
PWB-SUB LT2240
PWB-TUNER LT2240
79PQ6596
3A290003
7A930033
25261691
7A930029
79PQ6630
LT-2240 PARTS LIST
Description
AC-ADAPTER (SEB150P2-20.0B)
BACK-UNIT (CABINET-BACK LT2220/2240)
BEZEL (INCLUDES INNER BEZEL & PLATE)
BEZEL-UNIT (LC-T2240 GRY)
CORD-POWER (1.9M 2P BLK)
COVER-LEFT
COVER-REAR (CLEAR)
COVER-RIGHT
COVER-TERMINAL LEFT
COVER-TERMINAL RIGHT
LCD (LC56XWC8V-02) T/A REQ
LED (SML78420C)
PWB-CONTROL/LED T/A REQUIRED
PWB-MAIN (LT-2240) T/A REQUIRED
PWB-SUB T/A REQUIRED
PWB-TUNER
REMOTE
REMOTE-RECEIVER (GP1UD263XK)
SPEAKER-UNIT(ST-220-1)
STAND-UNIT (GREY)
TUNER (115V VF045AR)
UNIT-INVERTER (J191007.01)
Part Number
25327961
08LB10AE
25327891
7A081022
25435841
25435861
25435831
25435851
25435881
25435871
25327951
3A684029-M
3A681009
25620101
7A930031
PWB-CONTROL LT3020
8BL71M12
PWB-SUB LT3020
PWB-TUNER LT3020
7A930037
3A290003
7A930034
25261681
7A930029
LT-3020 PARTS LIST
Description
BACK-UNIT
BEZEL (INCLUDES INNER BEZEL & PLATE)
BEZEL-INNER (LC-T3020)
CORD-POWER (2.0M 2P BLK)
COVER-CORD
COVER-LEFT
COVER-REAR
COVER-RIGHT
COVER-TERMINAL LEFT
COVER-TERMINAL RIGHT
FRONT-CABINET (W/BUTTONS LT-3020)
LCD (LC300W01 A3 LGPL) T/A REQ
LED (SML78420C)
PLATE (COSMETIC LC-T3020)
POWER-UNIT (HS210N2J)(T/A REQ)
PWB-CONTROL/LED T/A REQUIRED
PWB-MAIN (LT-3020) T/A REQUIRED
PWB-SUB T/A REQUIRED
PWB-TUNER T/A REQUIRED
REMOTE(EUR7616Z20/Z2A)
REMOTE-RECEIVER (GP1UD263XK)
SPEAKER-UNIT(ST-300-1)
STAND-UNIT (GREY)
TUNER (115V VF045AR)
Part Number
25327961
08LB10AE
25327952
7A392043
79PQ6612
25435841
25435861
25435831
25435851
25435881
25435921
3A684029-M
3A681009
7A930031
PWB-CONTROL LT3040
8BL73M15
PWB-SUB LT3040
PWB-TUNER LT3040
79PQ6596
3A290003
7A930034
25261681
7A930029
LT-3040 PARTS LIST
Description
BACK-UNIT
BEZEL (INCLUDES INNER BEZEL & PLATE)
BEZEL-UNIT
CABLE-ANT(BLACK RF-RF)
CORD-POWER(2.0M 2P BLK)
COVER-CORD
COVER-LEFT
COVER-REAR
COVER-RIGHT
COVER-TERMINAL LEFT
COVER-TERMINAL RIGHT
LCD (LC300W01 A3 LGPL) T/A REQ
LED (SML78420C)
POWER-UNIT (HS210N2J)(T/A REQ)
PWB-CONTROL/LED T/A REQUIRED
PWB-MAIN (LT-3040) T/A REQUIRED
PWB-SUB T/A REQUIRED
PWB-TUNER T/A REQUIRED
REMOTE
REMOTE-RECEIVER (GP1UD263XK)
SPEAKER-UNIT(ST-300-1)
STAND-UNIT (GREY)
TUNER (115V VF045AR)
Page 54
MODELS: LT-2220 / LT-2240 / LT-3020 / LT-3040 / LT-3050
Part Number
08LB20AE
3A684029-M
8BL72M15
25327961
25327952
7A392043
79PQ6612
25435841
25435861
25435831
25435851
25435881
25435921
3A681009
7A930031
PWB-CONTROL LT3050
PWB-SUB LT3050
PWB-TUNER LT3050
79PQ6618
3A290003
7A930034
25261681
7A930029
LT-3050 PARTS LIST
Description
BEZEL (INCLUDES INNER BEZEL & PLATE)
LCD (LC300W01 A3 LGPL) T/A REQ
PWB-MAIN (LT-3050) T/A REQUIRED
BACK-UNIT
BEZEL-UNIT
CABLE-ANT(BLACK RF-RF)
CORD-POWER(2.0M 2P BLK)
COVER-CORD
COVER-LEFT
COVER-REAR
COVER-RIGHT
COVER-TERMINAL LEFT
COVER-TERMINAL RIGHT
LED (SML78420C)
POWER-UNIT (HS210N2J)(T/A REQ)
PWB-CONTROL/LED T/A REQUIRED
PWB-SUB T/A REQUIRED
PWB-TUNER T/A REQUIRED
REMOTE
REMOTE-RECEIVER (GP1UD263XK)
SPEAKER-UNIT(ST-300-1)
STAND-UNIT (GREY)
TUNER (115V VF045AR)
Page 55