Audiovox FPE2607DV Owner`s manual

FPE2607DV
26” HD FLAT PANEL LCD TV
WITH BUILT-IN DVD PLAYER
OWNER'S MANUAL
FOR ASSISTANCE CALL CUSTOMER SERVICE AT 1-800-645-4994
OR VISIT US AT WWW. AUDIOVOX.COM
PLV31260CS10 / AUDIOVOX
I/B 811-312691W030 <English>
SIZE : 148 X 210MM
MATERIAL : 80g WOODSFREE PAPER
128-8139
Printed in China
811-312691W030
SAFETY PRECAUTIONS
PLACEMENT INFORMATION
• Do not use this unit in places which are
extremely hot, cold, dusty or humid.
• Do not restrict the air flow of this unit by placing
it somewhere with poor air flow, by covering it
with a cloth, by placing it on bedding or carpeting.
SAFETY INFORMATION
WARNING : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
• When connecting or disconnecting the AC
power cord, grip the plug and not the cord itself.
Pulling the cord may damage it and create a
hazard.
• When you are not going to use the unit for a
long period of time, disconnect the AC power
cord.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
This
product
contains a low
power laser device.
CONDENSATION INFORMATION
• When left in a heated room where it is warm
and damp, water droplets or condensation may
form inside the equipment. When there is
condensation inside the unit, the unit may not
function normally. Let the unit stand for 1-2 hours
before turning the power on or gradually heat
the room and let the unit dry before use.
RATING PLATE LOCATION
The rating plate is located on the rear of unit.
FCC STATEMENTS
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
NOTE: This unit has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This unit generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio
communication. However, there is not guarantee
that interference will not occur in a particular
installation. If this unit does cause harmful
interference to radio or television reception, which
can be determined by turning the unit off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the unit and
receiver.
- Connect the unit into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
INVISIBLE LASER RADIATION WHEN UNIT IS
OPENED AND INTERLOCKS ARE DEFECTED.
AVOID EXPOSURE TO LASER BEAM.
The symbol for Class II
(Double Insulation)
CAUTION
• DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
• TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT OF
WALL OUTLET, THEN FULLY INSERT.
• USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
WARNING :
• TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT PLACE OBJECTS FILLED WITH LIQUIDS
ON OR NEAR THIS UNIT.
• SHOULD ANY TROUBLE OCCUR, DISCONNECT
THE AC POWER CORD AND REFER SERVICING
TO A QUALIFIED TECHNICIAN.
WARNING: Changes or modifications to this unit
not expressly approved by party responsible for
compliance could void the user authority to operate
the unit.
E-1
PLV31260_ib_eng_1-16_AUD.pmd
1
9/13/2007, 3:33 PM
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
Install
in
accordance
with
the
manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (Including
amplifiers) that produce heat.
9) Do not defect the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or the
third prong is provided for your safety.
If the provided plug does not fit into your
wall outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the
apparatus.
11) Only use attachments / accessories
specified by the manufacturer.
12) Use only with the cart, stand,
tripod, bracket, or table
specified
by
the
manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving the cart
/ apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long
periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as the power cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
MAINTENANCE
CLEANING THE DISC
A defective or dirty disc inserted into the unit can cause sound to drop out during
playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface of the disc.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
• NEVER use solvents such as benzene or alcohol to clean the disc.
• Do NOT use irregular shaped discs (for example : heart shaped, octagonal, etc.). They may cause
malfunctions.
CLEANING THE UNIT
• Be sure to turn the unit off and disconnect the AC power cord before cleaning the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth which
has been dipped in a weak soap-and-water solution and wrung out thoroughly. Then wipe it with a
dry cloth.
• Never use alcohol, benzene, paint-thinner, cleaning fluid or other chemicals. Do NOT use compressed
air to remove dust.
IMPORTANT NOTE
Before shipping the unit, remove the disc from the disc compartment.
E-2
PLV31260_ib_eng_1-16_AUD.pmd
2
9/13/2007, 3:33 PM
CONTENTS
SAFETY PRECAUTIONS ................................ 1
PLAYING A DISC ..................................... 23-24
IMPORTANT SAFETY INSTRUCTIONS
............................................................................. 2
Playing a Disc ............................................. 23
Playing a Picture File Disc ......................... 23
Pausing Playback (Still Mode) ................... 23
Stopping Playback ....................................... 23
Skipping to a Different Track ..................... 23
Fast Forward / Fast Reverse ................... 24
Slow-motion Play (DVD) ............................. 24
Audio Selection (DVD) .............................. 24
Subtitle Selection (DVD) ............................ 24
Angle Selection (DVD) .............................. 24
MAINTENANCE ................................................ 2
CONTENTS ....................................................... 3
DISC FORMATS .............................................. 4
ACCESSORIES ................................................ 5
GETTING STARTED ......................................... 5
CONTROL REFERENCE GUIDE ................. 6-9
CONNECTIONS ........................................ 10-14
Connecting a TV Antenna / Cable / Satellite
...................................................................... 10
Connecting an A / V Device ........................ 10
Connecting Devices with a Composite (Yellow
RCA-Type) Video Output ........................... 11
Connecting Devices with a Composite (Yellow
RCA-Type) Video Input .............................. 11
Connecting a High Definition (HD) Source
...................................................................... 12
Connecting a PC ......................................... 12
Connecting HDMI ......................................... 13
Connecting an Audio Amplifier .................... 13
Connecting the AC Power Cord ................ 14
SPECIAL FUNCTION ...................................... 25
USING HEADPHONES ................................... 14
Title / Chapter Programmed Playback (DVD)
.................................................................... 27
Track Programmed Playback (CD) ............ 27
Display ........................................................ 25
Locating a Specific Title (DVD) ................. 25
Locating a Specific Chapter / Track .......... 25
Locating a Specific Time (DVD) ................ 25
REPEAT PLAYBACK ...................................... 26
Repeating a Chapter / Title (DVD) ............. 26
Repeating a Single Track / an Entire Disc (CD)
.................................................................... 26
Repeating a Specific Section (DVD)(CD) ... 26
DVD/CD PROGRAMMABLE PLAYBACK
........................................................................... 27
INSTALLATION ............................................... 15
Removing the Base Stand .......................... 15
CUSTOMIZING THE FUNCTION SETTINGS
........................................................................... 28
Mounting on the Wall .................................. 15
UNIT OPERATION ........................................... 16
Language Setup ....................................... 28
Video Setup .............................................. 28
System Setup ........................................... 28
SOUND SYSTEM ............................................ 16
TV SETUP ................................................ 17-22
TROUBLESHOOTING GUIDE ....................... 29
Video Menu ................................................ 17
Audio Menu ............................................... 18
TV Menu ..................................................... 19
Setup Menu .......................................... 20-21
Parental Menu ..................................... 21-22
E-3
PLV31260_ib_eng_1-16_AUD.pmd
3
9/13/2007, 3:33 PM
DISC FORMATS
NOTES ON COPYRIGHT
ICONS USED ON DVDs
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public or rent
copyrighted material without permission.
Apparatus Claims of U.S. Patent Nos. 4,907,093;
5,315,448 and 6,516,132 licensed for limited
viewing uses only.
DVDs are copy protected, and any recordings
made from these discs will be distorted. This
product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for home
and other limited viewing uses only, unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Sample Icons:
The unit can play:
DVDs [8cm/
12cm disc]
Audio
CDs
[8cm/12cm disc]
2
2
1. English
2. French
Language selections for audio
1. English
2. French
Language selections for subtitles
LB
Screen aspect ratio
2
Multiple camera angles
1
Region code indicator
NOTE
When playing back a CD-G (Graphics) or CD
EXTRA disc, the audio portion will be played, but
the graphic images will not be shown.
TITLES, CHAPTERS AND TRACKS
• DVDs are divided into “TITLES” and
“CHAPTERS”. If the disc has more than one
movie on it, each movie would be a separate
“TITLE”. “CHAPTERS” are sections of titles.
Titel 1
CD-R CD-RW
Titel 2
Compatible
Chapter 1
Chapter 2
Chapter 3
Chapter 1
Chapter 2
REGION MANAGEMENT INFORMATION
Region Management Information: This unit is
designed and manufactured to respond to the
Region Management Information that is encoded
on DVDs. If the region number printed on the DVD
does not correspond to the region number of this
unit, this unit cannot play that disc.
• Audio CDs are divided into “TRACKS”. A
“TRACK” is usually one song on an Audio CD.
Track 1
The region number of this equipment is 1 .
Track 2
Track 3
NOTES ON UNAUTHORIZED DISCS
When the
symbol appears on the screen, it
indicates that the function or operation attempted
is not available at that time. This occurs because
the DVD manufacturer determines the specific
functions. Certain functions may not be available
on some discs. Be sure to read the documentation
provided with the DVD.
You may not be able to playback some DVDs on
this equipment if they were purchased from outside
your geographic area or made for business
purposes.
E-4
4
Track 5
NOTE
Numbers identify each title, chapter and track on
a disc. Most discs have these numbers record on
them, but some do not.
DISC FUNCTION OR OPERATION THAT
IS NOT AVAILABLE
PLV31260_ib_eng_1-16_AUD.pmd
Track 4
9/13/2007, 3:33 PM
ACCESSORIES
Please check and identify the supplied accessories.
Remote Control (with batteries) ................................................................................................. x 1
GETTING STARTED
USING THE REMOTE CONTROL
• Point the remote control at the remote sensor located on the unit.
• When there is a strong ambient light source, the performance of the infrared remote sensor may be
degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 16 feet (5 meters).
TO INSTALL BATTERIES
1. Open the battery door.
2. Insert 2 “AAA” batteries.
_
+
_
+
BATTERY REPLACEMENT
When the batteries become weak, the operating distance of the remote control is greatly reduced and
you will need to replace the batteries.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
NOTES
• If the remote control is not going to be used for a long time, remove the batteries to avoid damage
caused by battery leakage corrosion.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries.
• Always remove batteries as soon as they become weak.
• Weak batteries can leak and severely damage the remote control.
• WARNING : Do not dispose of batteries in a fire. Batteries may explode or leak.
WARNING : Do not dispose of batteries in a fire. Batteries may explode or leak.
Many universal remote controls have a “learning” feature. We recommend you use that feature to
program the remote control.
For any questions or problems related to programming a universal remote control, you must contact the
customer service department of the universal remote control manufacturer for assistance, or refer to
the instructions included with the universal remote control. We cannot offer assistance in programming
universal remote controls.
E-5
PLV31260_ib_eng_1-16_AUD.pmd
5
9/13/2007, 3:33 PM
CONTROL REFERENCE GUIDE
REMOTE CONTROL
6. VOLUME (- / +) buttons
Press to adjust the volume level.
7. CURSOR ( , , , ) buttons
Press to highlight selections on a menu
screen and adjust certain settings.
ENTER button
Press to confirm selections on a menu
screen.
8.
/
buttons
: Fast reverse playback.
: Fast forward playback.
9. PREV
button
Press to select previous chapters or
tracks on a disc.
10. SUBTITLE button
Press to select one of the subtitle
languages programmed on a DVD.
11. ANGLE button
Press to switch the camera angle of the
video presentation when scenes with
multiple camera angles are recorded on
a DVD.
12. TITLE button
Press to show the Title menu.
13. GOTO button
Press to skip directly to a specific
location on a DVD/CD.
14. MEMORY button
Press to set predetermined playback.
CLEAR button
Press to clear input selections.
15. MTS button
Press to switch between MONO sound,
STEREO sound and Secondary Audio
Program (SAP).
CC button
Press to activate the Closed Captioning
feature. This function only works on
programs broadcasted with captions.
16. EXIT button
Press to exit the TV SETUP menu and
return directly to normal viewing.
SLEEP button
Press to set the SLEEP timer. The unit
will remain on for the time that is set,
and will automatically shut off
afterwards.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1.
2.
3.
4.
5.
REPEAT
STANDBY / ON button
Press to turn ON the unit or put it in
STANDBY (OFF) mode.
TV button
Press to switch to TV mode.
DVD button
Press to switch to DVD mode.
AV button
Press to switch to source connected to
AV1 / AV2 (composite) input.
HD button
Press to switch to source connected to
YUV in / HDMI 1 / HDMI 2 (component)
inputs.
Number (0 - 9) buttons
• [dot] button
Use to enter digital sub-channels. (i.e.
11.3 or 12.7)
MENU button
Press to display the on-screen TV menu.
E-6
PLV31260_ib_eng_1-16_AUD.pmd
6
9/13/2007, 3:33 PM
CONTROL REFERENCE GUIDE
REMOTE CONTROL
22.
button
Press to stop playing a disc.
Press to go to a folder list of picture file
list.
PLAY button
Press to start and resume playback of a
disc.
PAUSE button
Press to pause playback and single
frame advance.
23. AUDIO button
Press to select audio soundtracks on a
DVD or change the output mode of a CD.
SLOW button
24.
Press to perform slow forward playback
of a DVD.
25. DVD MENU button
Press to enter the main menu of the DVD.
26. SETUP button
Press to enter and exit the SETUP menu
of the DVD.
27. REPEAT A-B button
Press to perform point-to-point repeat
playback on a DVD or CD.
REPEAT DISC button
Press to repeat a chapter or title of a DVD.
Press to repeat a single track or whole
CD.
28. DISPLAY button
Press to change disc status information
displayed on the screen.
SOUND button
Press to select from preset sound
settings to match the type of show you
are watching. (Standard / Personal /
Theater / Voice / Music)
29. LCD MODE button
Press to set size of LCD display.
PICTURE button
Select from preset screen display
settings to match the type of show you
are watching. (Personal / Soft / Movie /
Standard / Dynamic)
17
18
19
20
21
22
23
24
25
26
27
28
REPEAT
29
17. FUNCTION button
Press to switch between TV / AV 1 / AV 2 /
YUV in / DVD / HDMI 1 / HDMI 2 / PC in.
18. LAST CH button
Press to switch repeatedly between the
last two channels displayed.
button
19. MUTE
Press to turn off the sound.
20. CH
/ CH buttons
to change the channels.
Press /
21. NEXT
button
Press to select the next title, chapter or
track on a disc.
E-7
PLV31260_ib_eng_1-16_AUD.pmd
7
9/13/2007, 3:33 PM
CONTROL REFERENCE GUIDE
FRONT & SIDE VIEWS
1. STD.BY / ON button
Turns the unit on and off.
2. MENU button
Enters the on-screen TV menu.
3. FUNCTION button
Selects TV / AV 1 / AV 2 / YUV in / DVD /
HDMI 1 / HDMI 2 / PC in.
4.
CH buttons
Confirms selections on the TV menu
screen and changes the TV channels.
5. - VOL + controls
Adjusts the volume level.
6. Removable stand
7. Color LCD screen
PLAY button
8.
Starts and resumes playback of a disc.
STOP button
Stops playing a disc.
PAUSE button
Pauses playback and single frame
advance.
PREV button
Goes back to previous chapters / tracks.
Performs fast reverse playback.
NEXT button
Advances chapters / tracks.
Performs fast forward playback.
OPEN / CLOSE button
Opens and closes the disc door.
9. Remote sensor
Receives the remote control signal.
Standby indicator
10. Speaker
11. DVD door
E-8
PLV31260_ib_eng_1-16_AUD.pmd
8
9/13/2007, 3:33 PM
CONTROL REFERENCE GUIDE
REAR VIEW
12
13
20
21
22
14
15
23
16
24
17
18
25
19
12. AUDIO IN (Left/Right) jacks (AV IN 2)
13. VIDEO IN jack (AV IN 2)
14. VIDEO IN jack (AV IN 1)
15. Headphones jack
16. TV ANTENNA terminal
17. AUDIO IN (Left / Right) jacks (AV IN 1)
18. S-VIDEO IN jack (AV IN 1)
19. AUDIO IN (Left / Right) jacks (YUV IN)
20. VIDEO / AUDIO OUT (Left / Right) jacks
(AV OUT)
21. PC IN MONITOR / VGA jack
22. AC Power Cord
23. HDMI jacks (HDMI IN 1 / HDMI IN 2)
24. PC IN AUDIO jack
25. Component Video input (Y / PB / PR)
jacks (YUV IN)
E-9
PLV31260_ib_eng_1-16_AUD.pmd
9
9/13/2007, 3:33 PM
CONNECTIONS
CONNECTING A TV ANTENNA / CABLE / SATELLITE
To view television channels correctly, a signal must be received from one of the following sources:
- An indoor or outdoor aerial antenna
- A cable system
- A satellite system
Connecting a Digital
Antenna
The tuner in this TV receives
ATSC TV signals from an
antenna.
This digital TV can receive
standard (SDTV) and high
definition (HDTV) over the air
broadcasts.
Satellite, cable or TV
antenna cable to TV
ANTENNA terminal
(cable not included)
Connecting an Analog
Antenna or Device
The tuner in this TV receives
NTSC TV signals, analog cable
signals or the RF output from a
satellite receiver, VCR or cable
box.
CONNECTING AN A/V DEVICE
To connect to other equipment such as a VCR, camcorder, satellite system or cable, etc.
Connecting to a VCR /
Camcorder / Satellite
System / Cable
To AUDIO
IN jacks
(AV IN 1)
Connect the AUDIO and S-VIDEO
cable (not included) as shown:
Make sure you connect the cable
from the other equipment (AUDIO
OUT and S-VIDEO OUT) to this
unit AV IN 1 (AUDIO IN and SVIDEO IN).
To S-VIDEO
IN jack
NOTE
Please refer to the user manual
for the other equipment for more
information.
To S-VIDEO OUT /
AUDIO OUT jacks
E - 10
PLV31260_ib_eng_1-16_AUD.pmd
10
9/13/2007, 3:33 PM
CONNECTIONS
CONNECTING DEVICES WITH A COMPOSITE (YELLOW RCA-TYPE) VIDEO OUTPUT
To connect A/V devices such as a VCR, video game system or camcorder:
Connecting to a VCR / Video Game System / Camcorder
Connect the AUDIO / VIDEO cable (not included) as shown:
Make sure you connect the cable from the other equipment (AUDIO and VIDEO OUT) to this unit AV IN 1
(AUDIO and VIDEO IN) or AV IN 2 (AUDIO and VIDEO IN).
To AUDIO /
VIDEO IN jacks
(AV IN 1)
To AUDIO / VIDEO
OUT jacks
AV IN 1
OR
AUDIO IN
To AUDIO /
VIDEO IN jacks
(AV IN 2)
VIDEO IN
AV IN 2
To AUDIO / VIDEO
OUT jacks
NOTE
Please refer to the user manual for the other equipment for more information.
CONNECTING DEVICES WITH A COMPOSITE (YELLOW RCA-TYPE) VIDEO INPUT
To connect A/V devices such as a VCR, PVR or camcorder:
Connecting to a VCR /
PVR / Camcorder
Connect the AUDIO / VIDEO
cable (not included) as shown:
Make sure you connect the
cable from the other equipment
(AUDIO and VIDEO IN) to this
unit (AUDIO and VIDEO OUT).
NOTE
Please refer to the user manual
for the other equipment for more
information.
To AUDIO /
VIDEO OUT
jacks
To AUDIO / VIDEO IN jacks
E - 11
PLV31260_ib_eng_1-16_AUD.pmd
11
9/13/2007, 3:34 PM
CONNECTIONS
CONNECTING A HIGH-DEFINITION (HD) SOURCE
High-Definition (HD) Devices with component video output must be connected to the YUV input.
Connect the component video cable and audio cable (not included) as shown.
Make sure you connect the component video cable and audio cable from the other equipment
(COMPONENT VIDEO OUT and AUDIO OUT) to this unit (COMPONENT VIDEO IN and AUDIO IN - YUV
IN).
To AUDIO
IN jacks
(YUV IN)
* May require a subscription
for
receiving
HD
channels. Check with
your cable/satellite service
provider for details.
To
COMPONENT
VIDEO IN jacks
(YUV IN)
To AUDIO
OUT jacks
To COMPONENT
VIDEO OUT jacks
NOTE
When connecting a DVD player to the television, the picture resolution is solely dependent upon the
resolution supported by the DVD player attached. DVD player resolutions vary from 480i to 1080i, and
this unit can support DVD players up to a maximum resolution of 1080i.
CONNECTING A PC
Connect the 15-pin D-SUB PC/VGA connector from your computer to the 15-pin D-SUB PC/VGA input on
this unit using a monitor cable and audio cable (not included) as shown.
Make sure you connect the
cable from the computer (PC
Connector and PC AUDIO) to
this unit (PC IN MONITOR / VGA
and AUDIO).
To PC AUDIO OUT jack
To PC connector
E - 12
PLV31260_ib_eng_1-16_AUD.pmd
12
9/13/2007, 3:34 PM
CONNECTIONS
CONNECTING HDMI
HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection
for use with DVD players, DTV, set-top boxes and other digital AV devices. HDMI was developed to
provide the technologies of High Bandwidth Digital Content Protection (HDCP) as well as Digital Visual
Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by
DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced or high-definition video plus standard to multichannel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to
2.2 gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors),
and communication between the AV source and AV devices such as DTVs.
HDMI, the HDMI logo
and High-Definition Multimedia
Interface are trademarks or
registered trademarks of HDMI
licensing LLC.
Connect the HDMI cable (not
included) as shown:
Make sure you connect the
cable from the source
equipment (HDMI OUT) to this
unit (HDMI IN).
Press the HD button to match
the video source output quality.
To HDMI
OUT jack
To HDMI
IN jack
CONNECTING AN AUDIO AMPLIFIER
This connection allows you to use an audio amplifier and external speakers.
Connect the AUDIO cable (not
included) as shown:
Make sure you connect the
cable from the other equipment
(AUDIO IN) to this unit (AUDIO
OUT).
To AUDIO
OUT jacks
To AUDIO IN jacks
E - 13
PLV31260_ib_eng_1-16_AUD.pmd
13
9/13/2007, 3:34 PM
CONNECTIONS
CONNECTING THE AC POWER CORD
• Connect the AC power cord into a wall outlet.
• Press the STD. BY / ON button on the left side of the unit or use the remote control to turn on the unit.
NOTES
• TO PREVENT ELECTRIC
SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE
SLOT OF WALL OUTLET,
THEN FULLY INSERT.
• When the AC power cord is
plugged in, the unit is not
completely disconnected from
the main power, even when
the power is turned off.
• Be sure the AC power cord
is disconnected and all
functions are off before
making connections.
• Make sure that all the
components are connected
correctly.
• When you are not going to
use the unit for a long period
of time, disconnect the AC
power cord.
To AC wall outlet
USING HEADPHONES
• Turn down the volume before
connecting headphones to the
unit, then adjust the volume
to your desired level.
• When headphones are
connected, no sound will
come from the front
speakers.
Headphones
(1/8” [3.5mm]
diameter plug)
NOTE
Avoid listening to sound at high
levels for prolonged periods of
time. This may be harmful to you
and may cause hearing loss.
E - 14
PLV31260_ib_eng_1-16_AUD.pmd
14
9/13/2007, 3:34 PM
INSTALLATION
REMOVING THE BASE STAND
WARNING: The LCD display is very fragile, and must be protected at all times when removing the base
stand. Be sure that no hard or sharp objects, or anything that could scratch or damage the LCD display,
come in contact with it. Do NOT place pressure on the rear of the unit at anytime because the screen
could crack.
1. Disconnect any cables or
cords connected to the unit.
2. Lay the unit down on a flat
surface, so the back side is
facing up, making sure to
place a soft cushioned
material (such as a blanket
or thick piece of foam)
beneath the screen.
3. Remove the 8 screws and
then remove the BASE
STAND from the unit.
MOUNTING ON THE WALL
This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 7 7/8” x 3 7/8”
(200mm x 100mm) mounting kit designed for flat-panel TVs (sold separately). Mount this unit according
to the directions included with the mounting kit.
NOTE
Remove the base stand before mounting the unit on the wall.
7 7/8”
3 7/8”
Six mounting
holes
E - 15
PLV31260_ib_eng_1-16_AUD.pmd
15
9/13/2007, 3:34 PM
UNIT OPERATION
TURNING THE UNIT ON
When the AC power cord is connected, press the STD. BY/ON
button to turn it on. Press the FUNCTION button to select desired
mode (TV / AV 1 / AV 2 / YUV in / DVD / HDMI 1 / HDMI 2 / PC in).
If you select DVD, the DVD logo will appear on the screen.
NOTE
When the unit is not going to be used for a long time, disconnect
the AC power cord from the AC wall outlet.
SOUND SYSTEM
DOLBY DIGITAL (FOR DVD)
Dolby Digital is a sound system developed by Dolby Laboratories Inc.
This unit automatically recognizes DVDs that have been recorded with Dolby Digital.
Not all Dolby Digital sources are recorded with 6 channels.
Some sources marked Dolby Digital may be recorded in Dolby Surround, a 2 channel system. Look for
this logo on your unit.
Manufacturer under license from Dolby Laboratories.
the double-D symbol are trademarks of Dolby Laboratories.
“Dolby” and
E - 16
PLV31260_ib_eng_1-16_AUD.pmd
16
9/13/2007, 3:34 PM
TV SETUP
VIDEO MENU
1. Press the MENU button.
2. Press the ENTER or
button to select Video.
or
button to select the options (Picture Mode, Brightness, Contrast, Saturation,
3. Use the
Tint, Sharpness or Color Temperature). Adjust them using the
or
button (The screen will
button to go into the detailed settings.
change to your desired setting); or press the ENTER or
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
Video
AV / YUV / DVD / HDMI MODE
Picture Mode
TV
Setup
Parental
Video
Personal
50
Brightness
Audio
Contrast
50
Saturation
50
Tint
0
Sharpness
4
Color Temperature
Audio
Setup
Parental
Audio
Setup
50
Contrast
50
Saturation
50
0
Video
Select EXIT Exit
4
Sharpness
Color Temperature
PC MODE
Video
Personal
Brightness
Tint
Standard
Video
Picture Mode
Standard
Select EXIT Exit
VGA SETTINGS IN PC MODE
Picture Mode
Personal
Video
Brightness
50
Contrast
50
Audio
VGA
Setup
Color Temperature
Standard
Parental
Parental
Video
Select EXIT Exit
VGA
Auto Adjust
H. Position
50
V. Position
50
Phase
3
Clock
127
Best definition
1,366 768
Select EXIT Return
Picture Mode
: Select from preset screen display settings to match the type of show you are
watching (Personal, Soft, Movie, Standard & Dynamic). (Select Personal mode
to recall your customed settings on brightness, contrast, saturation, tint,
sharpness and color temperature.)
Brightness
: Adjust the brightness of the picture. Brighten or darken the whole picture.
Contrast
: Adjust to sharpen the picture quality. The black portions of the picture become
richer in darkness and the white become brighter.
Saturation
: Adjust the color saturation of the picture.
Tint
: Adjust the tint of the picture. (Toward purple / Toward green)
Sharpness
: Adjust the sharpness level to improve detail in the picture.
Color Temperature : Adjust the three color temperature of the picture. Choose from Standard
(balanced), Warm (red white), or Cool (blue white) modes.
H. Position
: Center the image by moving it left or right.
V. Position
: Center the image by moving it up or down.
Phase
: Adjusts the image if there is flicker of screen letters, color misalignment, or
blurring.
Clock
: Adjusts the display clock to change width of the image.
- Resolution : 1,366 x 768 max
- Refresh Frequency : 60Hz max
E - 17
PLV31260_ib_eng_17-30.pmd
17
9/13/2007, 3:36 PM
TV SETUP
AUDIO MENU
1. Press the MENU button.
or
button to select Audio, then press the ENTER or
button to go into the Audio
2. Use the
settings.
3. Use the
or
button to select the options (Balance, Bass, Treble, Virtual Surround, Reverb or
Sound mode). Adjust them using the
or
button (The screen will change to your desired setting);
or press the ENTER or button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
AV / YUV / DVD / HDMI / PC MODE
NOTE
Experiment with different sound settings until you find the settings you prefer.
Balance
Bass
Treble
Virtual Surround
Reverb
Sound mode
:
:
:
:
:
Adjust the balance level toward the left or right speakers.
Adjust the bass range.
Adjust the treble range.
Switch on or off the virtual surround effect.
Select from preset sound settings (Concert, Living Room, Hall, Arena, Church,
Off) to match the type of show you are watching.
: Select from preset sound settings (Standard, Personal, Theater, Voice &
Music) to match the type of show you are watching. (Select Personal mode
to recall your custom settings on bass and treble.)
E - 18
PLV31260_ib_eng_17-30.pmd
18
9/13/2007, 3:36 PM
TV SETUP
TV MENU (For TV Mode Only)
1. Press the MENU button.
2. Use the
or
button to select TV. Press the ENTER or button to go into the TV settings.
3. Use the
or
button to select the options (Tuner Mode, Auto Scan, Auto Scan Add CH,
Channel Skip, MTS or Audio Language). Adjust them using the
or
button (The screen will
change to your desired setting); or press the ENTER or
button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
Video
Tuner Mode
Cable
Auto Scan
Audio
TV
Setup
Auto Scan Add CH
Channel Skip
MTS
Stereo
Audio Language
English
Parental
TV
Select EXIT Exit
Tuner Mode
: Antenna (over-the-air broadcasts, Ch 2-69) or Cable (cable/satellite broadcasts,
CH 1-135) mode is available.
Auto Scan
: Searches for usable stations and stores them in memory.
Auto Scan Add CH : Searches for more usable stations and adds them in memory. (The stations
stored before are still kept.)
Channel Skip
: Skip weak channels and the channels you do not like.
MTS
: Select from Stereo / SAP (Secondary Audio Program) / Mono.
Audio Language : Select from English / Spanish / French. (Available for digital channels if multiple
audio languages are broadcasted.)
NOTE
The SAP (Secondary Audio Program) feature allows a TV station to broadcast other information, which
could be audio in another language.
Channel Skip Setting:
1. Use the
or
button to select a channel. (Press the button to select the last channel of the page,
press again to go to the next page. Press the
button to select the first channel of the page, press
again to go to the previous page.)
2. Press the ENTER button to shift between skip or not skip the channel. (“ ” appears in the square
means skip the selected channel. The channel will not appear when you press the CH /CH
Button.)
Video
Audio
TV
Setup
Parental
2
Analog
3
Analog
4
Analog
5
Analog
5-1
Digital
6
Analog
7
Analog
8
Analog
9
Analog
10
Channel Skip
KPIX-DT
Analog
ENTER Enter
Select EXIT Return
E - 19
PLV31260_ib_eng_17-30.pmd
19
9/13/2007, 3:36 PM
TV SETUP
SETUP MENU
1. Press the MENU button.
2. Use the
or
button to select Setup. Press the ENTER or
button to go into the Setup settings.
3. Use the
or
button to select the options (OSD Language, Time Setup, Caption or Restore
setting). Adjust them using the
or
button (The screen will change to your desired setting); or
press the ENTER or button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
Video
AV / YUV / DVD MODE
OSD Language
Video
English
Time Setup
Audio
Restore setting
TV
OSD Language
English
Time Setup
Audio
Caption
Setup
Setup
Caption
Restore setting
Parental
Parental
Setup
Setup
Select EXIT Exit
Select EXIT Exit
HDMI / PC MODE
Video
OSD Language
OSD Language :
Select from English / Español / Français.
English
Time Setup
Audio
Restore setting
Setup
Parental
Setup
Select EXIT Exit
Time Setup Setting
Video
Time Zone
Video
Eastern Time
Time
Audio
Sleep Timer
Audio
Off
TV
TV
Setup
Setup
Parental
Parental
Time Setup
Time Zone
Sleep Timer
ENTER Enter
Time
Select EXIT Return
Time Update
Off
Date
2000/01/01
Time
07:42:49
Timer
Off
Power On Time
00:00:00
Power Off Time
00:00:00
ENTER Enter
Select EXIT Return
:Select the time zone from Eastern Time / Indiana / Central Time / Mountain Time / Arizona
/ Pacific Time / Alaska / Hawaii.
:Select the time to turn the unit to Standby mode automatically: Off -> 5 Minutes -> 10
Minutes -> 15 Minutes -> 30 Minutes -> 60 Minutes -> 90 Minutes -> 120 Minutes -> Off.
When you set the ‘Time’, the option will be shown:
Time Update
:Select On/Off to activate the following manual settings; Select Auto to synchronize time
with the digital TV channel signal.
Date
:Press the or button to locate the position, and press the number buttons to input date.
Time
:Press the or button to locate the position, and press the number buttons to input time.
Timer
:Select On to activate automatically power on/off.
Power On Time :Press the
or
button to locate the position, and press the number buttons to input
power on time.
Power Off Time :Press the
or
button to locate the position, and press the number buttons to input
power off time.
E - 20
PLV31260_ib_eng_17-30.pmd
20
9/13/2007, 3:36 PM
TV SETUP
Caption Setting
Video
Audio
Analog Closed Caption
Off
Digital Closed Caption
Off
Video
Audio
Digital Caption Style
TV
TV
Setup
Setup
Parental
Parental
Caption
ENTER Enter
Select EXIT Return
Caption Style
As Broadcaster
Font Size
Small
Font Style
Style 1
Font Color
Green
Font Opacity
Solid
Background Color
Black
Background Opacity
Translucent
Window Color
White
Window Opacity
Transparent
Digital Caption Style
Select EXIT Return
Analog Closed Caption : Select the analog closed caption or turn it off.
Digital Closed Caption : Select the digital closed caption or turn it off.
Digital Caption Style
: Select as Broadcaster to use the default digital caption style of the
broadcaster. Select Custom to activate the caption style items and set you
preferred detailed settings.
NOTE
This function only works on ATSC programs broadcast with captions.
Restore Setting
If you reset the TV to the factory settings, all your present settings on Video & Audio will be erased and
replaced by the factory’s default settings. However, picture settings in PC mode and Parental settings
will not be erased.
PARENTAL MENU
Password
1. Press the MENU button.
2. Use the
or
button to select Parental. Press the ENTER or button to confirm. The menu locked
screen will be displayed.
3. Enter a 4-digit password. Once entered, the screen will enter the Parental menu. The preset password
is 0000.
You can edit the parental control level or change the password. See Parental Control Settings on
the next page.
TV MODE
Video
AV / YUV / DVD / HDMI / PC MODE
Video
Password
Audio
Audio
TV
Setup
Setup
Parental
Password
Parental
Parental
Parental
Select EXIT Exit
Select EXIT Exit
If you forget the password,
enter " 8888 " to unlock parental control.
E - 21
PLV31260_ib_eng_17-30.pmd
21
9/13/2007, 3:36 PM
TV SETUP
Parental Control Setting
1. Use the
or button to select various Parental settings. Press the ENTER or button to go into the
detailed settings.
2. Use the , , and buttons to move among the rating levels. Press the ENTER button to change the
mode between Blocked and Allowed.
3. Press the EXIT button to return to the previous menu.
4. Repeat steps 1 - 3 to adjust other options.
5. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
Video
Video
Program Block
Rating Enable
On
U.S.TV Ratings
Change Password
Audio
Audio
Clean All
Setup
Setup
Parental
Parental
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
Parental
Program Block
Select EXIT Return
Open V-Chip
Select EXIT Return
Rating Enable : Select On to edit the following parental items. Select Off to disable parental control.
Open V-Chip : Reads the ratings from ATSC TV programs if there is rating information broadcasted,
and denies the channel when its rating is higher than the ratings you pre-set.
U.S.
TV
Ratings
U.S.
Movie
Ratings
Canadian
English
Ratings
Canadian
French
Ratings
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
G
PG
:
:
:
:
:
:
:
:
PG-13
:
R
:
NC-17
X
C
C8+
G
PG
:
:
:
:
:
:
14+
18+
G
8 ans+
13 ans+
16 ans+
18 ans+
:
:
:
:
:
:
:
Recommended for all children.
Recommended for all children age 7 and above.
General Audience.
Parental Guidance Suggested.
Parental Strongly Cautioned.
Mature Audience Only.
GENERAL AUDIENCES, Suitable for all ages.
PARENTAL GUIDANCE SUGGESTED - Some material may not be suitable for
children.
PARENTS STRONGLY CAUTIONED - Some material may be inappropriate for
children under 13.
RESTRICTED, Under 17 requires accompanying parent or adult guardian for
viewing in movie theaters.
No one 17 or under admitted in movie theaters,
Adults Only.
Children.
Recommended for children age 8 and older.
GENERAL AUDIENCES, Suitable for all ages.
PARENTAL GUIDANCE SUGGESTED - Some material may not be suitable for
children.
Viewers 14 years and older.
Adult Programming.
GENERAL AUDIENCES, Suitable for all ages.
Not recommended for young children.
Not suitable for children under the age of 13.
Not suitable for children under the age of 16.
Adult Programming.
E - 22
PLV31260_ib_eng_17-30.pmd
22
9/13/2007, 3:36 PM
PLAYING A DISC
This owner’s manual explains the basic instructions of this unit. Some DVDs are produced with
limited operation during playback. For example, many DVDs do not allow users to skip government
warnings, or in some cases previews or other features. This is not a defect in the unit. Refer to the
instruction notes of discs.
“ ” may appear on the screen during operation. A “ ” means that the desired operation is not
permitted by the unit or disc.
PLAYING A DISC
1. Press the STD. BY/ON button to turn on the unit.
2. Press the FUNCTION button repeatedly to select DVD mode or directly press the DVD button on the
remote, then press the ENTER button.
See CUSTOMIZING THE FUNCTION SETTINGS before proceeding to step 3.
3. Press the button to open the disc door.
4. Hold the disc by its edges and gently push it onto the spindle with label side facing towards you until
you hear a “click”.
5. Press the button to close the disc door.
After loading, for most DVDs, the unit will automatically start playing or take you to the main menu.
If the unit does not automatically start playing the DVD, press the
PLAY button.
PLAYING A PICTURE FILE DISC
This unit can play JPEG files recorded on a CD-R or CD-ROM disc.
1. Press the button to open the disc door.
2. Hold a JPEG file disc by its edge and gently push it onto the spindle with label side facing towards you
until you hear a “click”.
3. Press the button to close the disc door.
4. The unit will load the disc and automatically display the contents of the disc on the screen, while also
beginning to play the picture file. These files will then be played back one by one.
5. Press the STOP button to go to the folder list.
6. Use the , , or button to view and select desired file, then press the ENTER button to confirm
the selected file.
NOTES
• You can press the PAUSE button to freeze the picture, and press the
PLAY button to resume
slide show.
PREV or
NEXT button to change the picture. Press the
PREV button to
• You can press the
view the previous picture. Press the
NEXT button to view to the next picture.
• You can press the ANGLE button to rotate direction of the picture by 90°.
PAUSING PLAYBACK (STILL MODE)
Press the PAUSE button. To resume normal playback, press the
the PAUSE button, the picture advances one frame.
PLAY button. Each time you press
STOPPING PLAYBACK
Press the
STOP button at the location where you want to interrupt playback. To resume playback at
the position where the disc was stopped, press the
PLAY button.
SKIPPING TO A DIFFERENT TRACK
• Press the
PREV button to skip to the start of the current/previous track.
• Press the
NEXT button to skip to the next track.
• For an Audio CD, use the number buttons on the remote control to go directly to the desired track
number.
E - 23
PLV31260_ib_eng_17-30.pmd
23
9/13/2007, 3:36 PM
PLAYING A DISC
FAST FORWARD / FAST REVERSE
1. Press the SEARCH
or
SEARCH button when a disc is playing.
• The disc begins a fast scan at two times normal (x2) speed.
• Four speeds are available. Each time the SEARCH button is pressed, the speed of the fast scan
changes.
2. Press the
PLAY button when you have reached the desired point to resume playback at normal
speed.
SLOW-MOTION PLAY (DVD)
1. Press the
SLOW button on the remote control in play mode. Six speeds are available. Each time the
SLOW button is pressed, the speed of slow-motion playback changes in the following sequence:
SF 1/2
2. Press the
SF 1/3
SF 1/4
SF 1/5
SF 1/6
SF 1/7
PLAY button to return to the normal playback speed.
AUDIO SELECTION (DVD)
On some discs, the sound is recorded in two or more formats. Follow the directions below to select the
type of playback.
1. While a disc is playing, press the AUDIO button to show the
current audio format number.
: 1/3ENG
D 6CH
2. Press the AUDIO button repeatedly to select the desired audio
format.
NOTES
• If only one audio format is recorded, the number does not change.
• About two seconds later, playback continues in the new audio format.
SUBTITLE SELECTION (DVD)
1. While a DVD is playing, press the SUBTITLE button to display the current language
: 2/3 ESP
setting.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language.
NOTES
• If only one language is recorded, the language does not change.
• About two seconds later, playback continues with the new subtitle selected.
• The number of languages recorded differs depending on the disc.
• If no button is pressed within a few seconds, playback continues without changing the current
subtitle.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• On some DVDs, subtitles are activated from the main menu of the DVD. Press the DVD MENU button
to activate the main menu.
ANGLE SELECTION (DVD)
Some DVDs contain scenes that have been shot from a number of different angles. For these discs, the
same scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles recorded,
press the ANGLE button to view the number current angles
:[2/3]
available.
Sequence of angle shots
2. Press the ANGLE button repeatedly to change the scene to
(Example)
the next angle in those recorded.
:[1/3]
:[2/3]
:[3/3]
• About two seconds later, playback continues from the
new angle selected.
• If no button is pressed within 10 seconds, playback
continues without changing the current angle.
NOTES
• This function can only be used for discs on which scenes shot from multiple angles have been
recorded.
• If only one angle is recorded, “
1/1” is displayed.
E - 24
PLV31260_ib_eng_17-30.pmd
24
9/13/2007, 3:36 PM
SPECIAL FUNCTION
DISPLAY
While the disc is playing, press the DISPLAY button repeatedly to display information on operation
status.
Title
Chapter
TT 1/21
Audio
Angle
D 6
2/3 ESP
Chapter
Remaining time
TT 1/21
Title
00:07:18
Subtitle
1/3 ENG
Title
Elapsed time
CH 6/29
CH 11/29
Chapter
TT 1/21
CH 11/29
OFF
R -00:30:28
Total time
T -01:00:28
LOCATING A SPECIFIC TITLE (DVD)
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1. In STOP mode, press the GOTO button.
2. Press the or
button to highlight a specific field
00:00:00
TT 0 0/21 CH 029/029
and press the corresponding number button(s) for
the title you want.
3. Press the ENTER button to confirm. The unit will start playback about 3 second later.
LOCATING A SPECIFIC CHAPTER / TRACK
If you know the chapter / track number you want to play, you can locate a specific chapter / track by
directly selecting a chapter / track number.
1. Press the GOTO button to search for your desired
00:00:00
TT 00/34 CH 000/029
chapter / track.
2. Press the or
button to highlight a chapter / track
X
00:00:00
TRK 0 0 / 12
and press the corresponding number button(s) for
the chapter / track you want.
3. Press the ENTER button to confirm. The unit will start playback about 3 second later.
LOCATING A SPECIFIC TIME (DVD)
You can move to a specific location by entering its corresponding time (hours, minutes, seconds)
1. Press the GOTO button.
2. Press the or button to highlight a time and press
0 1 :00:00
TT 00/21 CH 029/029
the corresponding number button(s) for the setting
point you want.
3. Press the ENTER button to confirm. The unit will start playback about 3 second later.
NOTES
• Some discs may not respond to this process.
• This method of locating a title/chapter is available only on a DVD that contains title/chapter numbers.
• Some scenes may not be located as precisely as specified.
• This method for accessing specific locations is available only within the current title of the DVD.
E - 25
PLV31260_ib_eng_17-30.pmd
25
9/13/2007, 3:36 PM
REPEAT PLAYBACK
You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)
Repeating a Chapter (DVD)
You can play the same chapter repeatedly.
1. While the disc is playing, press the REPEAT DISC button until the
screen. The current chapter is played repeatedly.
indicator displays on the
Repeating a Title
You can play the same title repeatedly.
2. While the disc is playing, press the REPEAT DISC button until the
screen. The current title is played repeatedly.
indicator displays on the
To Resume Normal Playback
3. While the disc is playing, press the REPEAT DISC button until the
screen.
indicator displays on the
You can play a single track or an entire disc repeatedly.
Repeating a Single Track (CD)
You can play the same track repeatedly.
1. While the disc is playing, press the REPEAT DISC button until the
screen. The current track is played repeatedly.
indicator displays on the
Repeating an Entire Disc
2. While the disc is playing, press the REPEAT DISC button until the
screen. The entire disc is played repeatedly.
indicator displays on the
To Resume Normal Playback
3. Press the REPEAT DISC button until the
indicator displays on the screen.
Repeating a Specific Section (DVD) (CD)
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (
is
displayed) you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of the section (
is displayed) you want to play
repeatedly.
3. The unit will immediately begin replaying your selection.
To Resume Normal Playback
4. While the disc is playing, press the REPEAT A-B button until the
indicator displays on the
screen.
NOTES
• A-B repeat can only be used within the same title. If the start and end of the section to be repeated are
in different titles, A-B repeat is cancelled.
• The A-B repeat function does not operate in scenes where different camera angles are recorded.
E - 26
PLV31260_ib_eng_17-30.pmd
26
9/13/2007, 3:36 PM
DVD / CD PROGRAMMABLE PLAYBACK
PROGRAMMABLE MEMORY
The two types of programmed playback provided by this unit are title/chapter programmed playback and
track programmed playback.
Title /Chapter Programmed Playback (DVD)
1. In STOP mode, press the MEMORY button.
2. Enter the title numbers in
. Use the
or
button to move the highlight to chapter and enter the
.
chapter numbers in
3. Use the
, ,
or
button to move to other fields.
4. Repeat steps 2 to 3.
5. Press the
PLAY button to start the programmed playback.
Title
PROG
T C
T
Chapter
C
T
C
T
C
1--:--
5--:--
9--:--
13 - - : - -
2--:--
6--:--
10 - - : - -
14 - - : - -
3--:-4--:--
7--:-8--:-PLAY
11 - - : - 12 - - : - CLEAR
15 - - : - 16 - - : - -
Track Programmed Playback (CD)
1. In STOP mode, press the MEMORY button.
2. Enter the track numbers in
.
, ,
or
button to move to other fields.
3. Use the
4. Repeat steps 2 to 3.
5. Press the
PLAY button to start the programmed playback.
Track
PROG
1
2
3
4
-------------
5 ---6 ---7 ---8 ---PLAY
9 - - - - 13 - - - 10 - - - - 14 - - - 11 - - - - 15 - - - 12 - - - - 16 - - - CLEAR
E - 27
PLV31260_ib_eng_17-30.pmd
27
9/13/2007, 3:36 PM
CUSTOMIZING THE FUNCTION SETTINGS
LANGUAGE SETUP
1. Press the SETUP button in STOP mode.
2. Use the button to change the highlight cursor. Use the
or
button to select a language, then press the ENTER button The
screen will change to your selected language immediately.
3. To exit the SETUP MENU and return to the normal screen, press
the SETUP button.
VIDEO SETUP
1. Press the SETUP button in STOP mode.
button to select LANGUAGE SETUP, then press the
2. Use the
or button repeatedly until VIDEO SETUP appears.
3. Use the
or
button to select the option (BRIGHTNESS,
CONTRAST or VIDEO), then press the button. Use the
or
button to make adjustments, then press the ENTER button. The
screen will change to your selected setting.
4. Repeat steps 2 and 3 above to adjust other options.
5. To exit the SETUP MENU and return to the normal screen, press
the SETUP button.
SYSTEM SETUP
1. Press the SETUP button in STOP mode.
2. Use the
button to select LANGUAGE SETUP, then press the
or button repeatedly until SYSTEM SETUP appears.
3. Use the or button to select the option (TV TYPE or DEFAULT),
then press the
button. Use the
or
button to make
adjustments, then press the ENTER button. The screen will change
to your selected setting.
4. Repeat steps 2 and 3 above to adjust other options.
5. To exit the SETUP MENU and return to the normal screen, press
the SETUP button.
Cut off when a wide-screen video
image is played.
TV Type
Pan Scan
• When wide-screen video is played, this mode clips the right and
left sides of the image so that it can be viewed on a conventional
screen.
• Some wide-screen DVDs that do not permit Pan Scan playback
are automatically played in Letter Box mode (black bands at top
and bottom of screen).
Letter Box
• When wide-screen video is played in this mode on a conventional
screen, black bands appear at the top and bottom of the screen.
Wide-screen
• This is the correct mode for playing wide-screen videos on a
wide-screen.
NOTES
• The displayable picture size is preset on the DVDs. Therefore
the playback picture of some DVDs may not conform to the picture
size you select.
• When you play DVDs recorded in the 4:3 aspect ratio, the playback
picture will always appear in the 4:3 aspect ratio regardless of
the TV shape setting.
Default
It takes 3-5 seconds to reset the unit to the factory default.
PAN SCAN
LETTER BOX
WIDE SCREEN
E - 28
PLV31260_ib_eng_17-30.pmd
28
9/13/2007, 3:36 PM
TROUBLESHOOTING GUIDE
SYMPTOM
No power.
The remote does not
function.
DVD
No sound or only a
very low-level sound
is heard.
No picture.
CAUSE (AND REMEDY)
•
•
•
•
•
•
Check that the AC power cord is connected.
The unit is not turned on.
Remove any obstacles between the remote and the unit.
Use the remote near the unit.
Point the remote at the remote sensor on the unit.
Replace the batteries in the remote with new ones.
• Make sure that you select DVD mode.
• The system is in pause mode. Press the
PLAY button to return to normal
PLAY mode.
• Fast-forward or fast-reverse is performed. Press the
PLAY button to
return to normal play mode.
• Make sure the AUDIO / VIDEO output and AV IN input connections are correct.
• The DTS DVD disc cannot be decoded to have speaker output.
• The unit is too hot. Shut off the unit for 30 minutes to cool it down.
• The region number of the disc does not match the region number of this
unit.
The picture is not
clear.
Severe hum or noise
is heard.
• Clean the disc.
• The disc is scratched.
The disc does not
play.
•
•
•
•
TV
Bad Picture (snow,
multiple images,
distortion, blurry)
Black and white
picture.
No picture or sound.
Colored patches of
picture.
No sound is output
from the HDMI out
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened
with alcohol.
• Clean the disc.
There is no disc inside ("No Disc" appears on the screen).
Insert the disc correctly with the playback side facing down.
Clean the disc.
A non-valid disc has been inserted. The unit and disc region number are
incompatible.
• Condensation may have formed inside the unit due to a sudden change in
temperature. Wait about an hour for it to clear and try again.
• Check the location of the antenna and adjust it if necessary.
• Make sure the antenna cable is firmly connected.
• Make sure all input cables are firmly connected.
• Check the VIDEO MENU within the TV SETUP MENU.
• Check to make sure the program you are watching is broadcast in color and
not black & white.
• Make sure the unit is plugged in and turned on.
• Make sure that TV mode is selected.
• Try a new channel to check for possible station trouble.
• Make sure the antenna is connected properly.
• Increase the volume.
• Make sure the antenna or audio video source device is working properly.
• Make sure all cables are firmly connected.
• Check for local interference.
• Make sure there are no unshielded electrical devices nearby that are
causing interference.
• Turn the unit off for 30 minutes, then try it again.
• Check the connection between this unit and the HDMI out jack of other
equipment.
• See if the TV supports this 480p/576p/720p/1080i DVD system.
• Check your TV system setup correctly.
• Make sure your TV supports HDCP (High Bandwidth Digital Content
Protection).
E - 29
PLV31260_ib_eng_17-30.pmd
29
9/13/2007, 3:36 PM
Unit : INCH
26 1/4
22 5/8
19 3/4
8 1/4
18 3/4
5 1/8
7 7/8
8 5/8
3 7/8
Printed in China
811-312691W031
PLV31260_ib_eng_17-30.pmd
30
9/13/2007, 3:36 PM