Casio MA1001-A User`s guide

MA1001-EA
Operation Guide 5132
Congratulations upon your selection of this CASIO watch.
Power Levels
B
+
This watch does not have a city code that corresponds to the UTC offset of –3.5
hours for Newfoundland, Canada.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
or loss suffered by you or any third party arising through the use of this product or
its malfunction.
About This Manual
B
Button operations are indicated using the letters A
through D shown in the illustration.
@+
> * 6
5
our Hand
H
Second Hand
Minute Hand
Left Dial Hand: Indicates the current mode.
Lower Dial Hand
Right Dial Hands
Day
This User’s Guide uses numbers shown above to identify
watch hands and indicators.
Things to check before using the watch
Is the x Second Hand moving smoothly at one-second intervals?
NO
YES
The watch is charged sufficiently.
For details about charging, see
“Charging the Watch”.
YES
Power is low. Charge the watch by placing
it in a location where it is exposed to light.
For details, see “Charging the Watch”.
Function Status
1
Normal.
All functions enabled.
2
x Second Hand moving at two-second
intervals.
m Day changes to 1 (home position).
Beeper disabled.
3
x Second Hand stopped.
z Hour Hand and c Minute Hand stopped
at 12 o’clock.
All functions disabled.
••When power drops to Level 3, all functions will be disabled but the watch will
continue to keep time internally for about one week. If you recharge the battery
sufficiently during this period, the analog hands will move automatically to the
correct setting and regular timekeeping will resume. After one week, all settings
(including timekeeping) will be cleared. Recharging the battery will reset all settings
to their initial factory defaults.
Power Recovery Mode
1. Hold down C for about two seconds to enter the Timekeeping Mode, and
then observe the movement of the x Second Hand.
Is the x Second Hand moving at
two-second intervals or is it stopped
completely?
@ 5
Moving at two-second
intervals.
Level Hand Movement
Hand Functions
z
x
c
v
b
n
m
You can get an idea of the watch’s power level by
observing the movement of the x Second Hand in the
Timekeeping Mode.
••If the x Second Hand is moving normally at one-second
intervals, power is at Level 1.
••If the x Second Hand is moving at two-second intervals,
power is at Level 2, which is quite low. Expose the watch
to light as soon as possible so it can charge.
NEXT
Go to step 2.
2. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To configure Home City settings” to configure your Home
City and daylight saving time settings.
The watch is designed to go into a power recovery mode that stops hand operation
temporarily whenever power suddenly drops below a certain level due to overuse
of the alarm tone over a short period. Note that all operations are disabled while the
watch is in the power recovery mode.
The hands will move to the correct positions and the watch will resume normal
operation after power recovers (in about 15 minutes). Putting the watch in a location
where it is exposed to light will help power to recover sooner.
Charging Times
Exposure Level (Brightness)
Daily
Operation *1
Level Change *2
Level 3
Level 2
Level 1
Outdoor sunlight (50,000 lux)
8 minutes
2 hours
28 hours
Window sunlight (10,000 lux)
30 minutes
6 hours
104 hours
Window sunlight on cloudy day
(5,000 lux)
48 minutes
10 hours
–––
8 hours
110 hours
–––
Indoor fluorescent lighting (500 lux)
See “Configuring Current Time and Date Settings”.
**1 Approximate exposure each day to generate power for normal daily operation.
**2 Approximate exposure to take power up one level.
••The above exposure times all are for reference only. Actual exposure times depend
on lighting conditions.
••For details about the operating time and daily operating conditions, see the “Power
Supply” section of the Specifications.
The watch is now ready for use.
Power Saving
Charging the Watch
Power Saving enters a sleep state automatically whenever the watch is left for a
certain period in an area where it is dark. The table below shows how watch functions
are affected by Power Saving.
••There actually are two sleep state levels: “second hand sleep” and “function sleep”.
Important!
World Time settings depend on correct Home City, time, and date settings in the
Timekeeping Mode. Make sure these settings are configured correctly.
3. Set the current time.
The face of the watch is a solar cell that generates power from light. The generated
power charges a built-in rechargeable battery, which powers watch operations. The
watch charges whenever it is exposed to light.
Elapsed Time in Dark
Operation
60 to 70 minutes (second hand
sleep)
x Second Hand only is stopped at 12 o’clock, all other
functions are enabled.
Charging Guide
6 or 7 days (function sleep)
•• All functions, including analog timekeeping, disabled
•• Internal timekeeping maintained.
Whenever you are not
wearing the watch, be sure
to leave it in a location
where it is exposed to light.
••Best charging
performance is achieved
by exposing the watch to
light that is as strong as
possible.
When wearing the watch,
makes sure that its face is
not blocked from light by the
sleeve of your clothing.
••The watch may enter a
sleep state if its face is
blocked by your sleeve
even only partially.
••The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch
is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep
state.
••The watch will not enter a sleep state while it is in the Stopwatch Mode.
To recover from the sleep state
Move the watch to a well-lit area or press any button.
Warning!
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become
particularly hot when exposed to the following conditions for long periods.
••On the dashboard of a car parked in direct sunlight
••Too close to an incandescent lamp
••Under direct sunlight
Important!
••Keep the watch in an area normally exposed to bright light when storing it for long
periods. This helps to ensure that power does not run down.
••Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause power to run down.
Make sure that the watch is exposed to bright light whenever possible.
1
Operation Guide 5132
Mode Reference Guide
Your watch has four “modes”. The mode you should select depends on what you
want to do.
To toggle the Home City time between standard time and daylight saving time
1. Perform the step 1 under “To configure Home City settings”.
••Each time you select a city code, the z Hour Hand, c Minute Hand, and
b Lower Dial Hand move to the current time for that city code. Do not perform
the next operation until these hands stop moving.
To do this:
Enter this mode:
•• View the current time in your Home City and in one of
29 cities around the globe
•• Configure Home City and daylight saving time (DST)
settings
•• Configure time and date settings
Timekeeping Mode
Use the stopwatch to measure elapsed time
Stopwatch Mode
View the current time in one of 29 cities (time zones) around
the globe
2. Press B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
••In the city code setting mode, the v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
••Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
World Time Mode
3. After the setting is the way you want, press A to return to the Timekeeping Mode.
Set an alarm time
Alarm Mode
Note
••After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time
in your Home City.
**Coordinated Universal Time, the world-wide scientific standard of timekeeping. The
reference point for UTC is Greenwich, England.
Selecting a Mode
With this watch, everything starts from the Timekeeping Mode.
To determine the watch’s current mode
Check the position of the v Left Dial Hand as shown
under “To select a mode”.
To return to the Timekeeping Mode from any other
mode
Hold down C for about two seconds until the watch beeps
twice.
Configuring Current Time and Date Settings
You can configure current time and date settings.
To change the current time setting
1. In the Timekeeping Mode, keep A depressed (for about
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
••At this time, the v Left Dial Hand will indicate the
Home City’s current daylight saving time setting (STD
or DST).
>
Timekeeping Mode
The hand indicates
the day of the week.
C
To select a mode
Press C to cycle between the modes as shown below. The v Left Dial Hand
indicates the currently selected mode.
Stopwatch Mode
>
The hand points to 0.
>
@
B
2. Change the Home City and daylight saving time (DST)
settings, if you want.
••For details about these settings, see steps 2 and 3
under “To configure Home City settings”.
••In the following steps, each press of C cycles
between settings as shown below.
@+
World Time Mode
Home city/DST
Hour/Minute
Year
Alarm Mode
The hand points to STD
or DST.
The hand points to ALM.
Day
Month
> *
3. Press C.
••The watch will beep, and the x Second Hand and v Left Dial Hand will move to
their 12 o’clock positions. This is the time setting mode.
Timekeeping
Use the Timekeeping Mode to view the current time and date. To enter the
Timekeeping Mode from any other mode, hold down C for about two seconds.
B
@+
> * 6
5
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand: Indicates the day of the week.
b Lower Dial Hand: Indicates the current hour in the
Home City time in 24-hour format.
n Right Dial Hands:
Indicate the current time in the World Time City in
24-hour format.
m Day
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
@
B
+
> *
@
5
To configure Home City settings
Note
••This watch does not have a city code that corresponds
to Newfoundland.
1. In the Timekeeping Mode, keep A depressed (for about
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
••This indicates the city code setting mode.
••The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
••For details about city codes, see the “City Code
Table”.
2. To change the Home City setting, press D to move the
x Second Hand clockwise.
••Keep pressing D until the x Second Hand is pointing
at the city code you want to select as your Home City.
••Each time you select a city code, the z Hour Hand,
c Minute Hand, b Lower Dial Hand and m Day
move to the current time and date for that city code.
Do not perform the next operation until these hands
stop moving.
3. Press B to toggle the time for the currently selected
city code between STD (standard time)/DST (daylight
saving time).
••In the city code setting mode, the v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
••Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
4. Use D (+) and B (–) to change the time (hour and minute) setting.
••Each press of either button will move the hands (z Hour Hand and c Minute
Hand) one minute.
••Holding down D or B will start high-speed z Hour Hand and c Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
••The b Lower Dial Hand and z Hour Hand move in sync with each other.
••When setting the time, make sure that the b Lower Dial Hand indicates the
proper a.m./p.m. hour.
••If you want to change the date setting at this time, press C and perform the
procedure starting from step 3 under “To change the current date setting”.
5. After the time setting is the way you want, press A to return to the Timekeeping
Mode.
••This will cause the x Second Hand to move automatically to 12 o’clock and
resume movement from there.
To change the current date setting
1. In the Timekeeping Mode, keep A depressed
00
(for about five seconds) as the x Second Hand
@
10
moves to the city code of the currently selected
Home City.
20
90
30
80
40
70
50
60
Setting the year (tens digit)
2. Press C twice.
••The watch will beep and change to the year
setting mode.
••The year can be set in the range of 2000 to
2099.
••You can save your settings and exit the
setting procedure at any time by pressing A,
which will return to the Timekeeping Mode.
This will cause the x Second Hand to move
automatically to 12 o’clock and resume normal
movement from there.
3. Use D to change the tens digit of the year setting.
••Each press of D will move the x Second Hand and change the tens digit of the
year setting.
4. After the tens digit of the year setting is the way you want, press C.
••The watch will beep and change to the ones digit of the year setting mode.
0
@
5. Use D to change the ones digit of the year
setting.
••Each press of D will move the x Second
Hand and change the ones digit of the year
setting.
1
2
9
3
8
4
7
6
6. After the ones digit of the year setting is the way
you want, press C.
••The watch will beep and change to the month
setting mode.
5
Setting the year (ones digit)
4. After the setting is the way you want, press A to return to the Timekeeping Mode.
2
Operation Guide 5132
Nov
Dec
7. Use D to move the x Second Hand to the month
setting you want.
Jan
8. After the month setting is the way you want,
press C.
••The watch will beep and change to the day
Mar
setting mode.
Feb
Oct
Sep
Aug
Apr
Jul
@
May
Jun
Setting the month
9. Use D (+) and B (–) to change the m Day
setting.
••If you want to change the time setting at this
time, press C and then perform the procedure
starting from step 3 under “To change the
current time setting”.
@
>
5
Using the Stopwatch
2. Now you can perform either of following stopwatch operations.
To perform an elapsed time operation
B
(Restart)
B
D
(Stop)
Reset
To pause at a split time
D
B
Start
B
Stop
D
Reset
Note
••The Stopwatch Mode can indicate elapsed time up to 23 minutes, 59.99 seconds.
••D
button operation (split, reset) is disabled while hands are moving at high speed
following a reset operation and when transitioning from a split time back to normal
elapsed timekeeping.
••Once started, stopwatch timing continues until you press B to stop it, even if you
exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch
limit defined above.
••If the stopwatch was not reset after the last elapsed time operation, timing will
restart from where it was last stopped, and not from 0.
••The x Second Hand indicates the 1/10-second count for the first 30 seconds
of a stopwatch elapsed time operation. After that, the hand stops at 12 o’clock
position. 1/10-second timing continues internally after the first 30 seconds, and the
x Second Hand will jump to the current value whenever B (Stop) or D (Split) is
pressed.
••Though the v Left Dial Hand is stopped while an elapsed time measurement
operation is in progress, the watch keeps track of the 1/100-second count
internally. The v Left Dial Hand will jump to the current 1/100-second reading
whenever you stop the stopwatch or perform a split time operation.
You can use the World Time Mode to view the current time in one of 29 time zones
around the globe. The city that is currently selected in the World Time Mode is called
the “World Time City”.
>
6
After
swapping
New York
9:08 a.m.
(Daylight saving time)
Tokyo
10:08 p.m.
(Standard time)
••After swapping the Home City and World Time City, the watch will stay in the
World Time Mode. The x Second Hand will point to your new World Time City
(TYO in this example).
••The n Right Dial Hands will indicate the current time in your new World Time
City.
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
@
Checking the Current Time in a Different Time Zone
@
New York
9:08 a.m.
(Daylight saving time)
2. Hold down B for about three seconds until the watch
beeps.
••This will make the World Time City (NYC in this
example) your new Home City. At the same time, it will
change the Home City you had selected prior to step 2
(TYO in this example), to your new World Time City.
@
Normal stopwatch hand movement will
resume automatically after five seconds.
Split
World Time City
Tokyo
10:08 p.m.
(Standard time)
Stop
Home City
Before
swapping
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
••In this example, you would move the x Second Hand
6
to NYC in order to select New York as the World
Time City.
••Wait until the n Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
To perform elapsed time measurement
1. Use C to move the v Left Dial Hand to 0.
B
The following example shows what happens when the
Home City and World Time City are swapped while the
Home City originally is TYO (Tokyo) and the World Time
City is NYC (New York).
6
Start
2. Hold down A for about two seconds until the watch
beeps. This will cause the v Left Dial Hand to toggle
between DST (daylight saving time) and STD (standard
Hold down
time).
A for two
••Note that you cannot switch between STD (standard
seconds
time)/DST (daylight saving time) while UTC is selected
as the World Time City.
••Note that the STD (standard time)/DST (daylight
saving time) setting affects only the currently selected
time zone. Other time zones are not affected.
6
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
Hand Functions
x Second Hand: Indicates the stopwatch 1/10-second
count.
v Left Dial Hand: Indicates the stopwatch 1/100-second
count.
n Right Dial Hands: Indicate the stopwatch minutes
(short hand) and seconds (long
hand).
@
B
>
@
The stopwatch measures elapsed time and split times.
>
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use D to select the city code
whose setting you want to change.
••Wait until the n Right Dial Hands complete their move
to the time in the currently selected World Time City.
You will not be able to perform step 2 of this procedure
until the hands stop moving.
Note
••The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s rechargeable battery replaced or after
power drops to Level 3.
2. Use D to move the x Second Hand to the city code you want to select as the
World Time City.
••The n Right Dial Hands will move to the current time in the time zone of the
current city code. At this time, the z Hour Hand and c Minute Hand will
continue to indicate the current time in the Home City.
••For full information on city codes, see the “City Code Table”.
••If you think that the time indicated for the selected time zone is not correct, it
probably means that there is something wrong with your Home City settings.
Use the procedure under “To configure Home City settings” to correct the Home
City settings.
10. After the settings are the way you want, press A
to return to the Timekeeping Mode.
••The day of the week indicated by the v
Left Dial Hand changes automatically in
accordance with the date (year, month, and
day).
To view the time in another time zone
1. Use C to move the v Left Dial Hand to STD or DST.
••The x Second Hand will move to the city code of the currently selected World
Time City.
Hand Functions
x Second Hand:
Indicates the currently selected World Time City.
v Left Dial Hand:
Indicates the current STD (standard time) or DST
(daylight saving time) setting of the currently selected
time zone.
n Right Dial Hands:
Indicate the current time in the selected World Time
City in 24-hour format.
>
Hand Functions
x Second Hand:
Indicates the current alarm ON/OFF setting.
v Left Dial Hand: Points to ALM.
n Right Dial Hands:
Indicate the current alarm time setting in 24-hour
format.
6
To change the alarm time setting
1. Use C to move the v Left Dial Hand to ALM.
2. Use D (+) and B (–) to change the alarm time setting.
••Each press of either button will move the n Right Dial Hands one minute.
••Holding down D or B will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
••The alarm always works based on the time kept in the Timekeeping Mode.
••The watch will return to the Timekeeping Mode automatically if you do not
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm on and off. The x Second Hand will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
3
Operation Guide 5132
Adjusting the Home Positions
Strong magnetism or impact can cause the hands and/or date of the watch to be off.
If this happens, perform the applicable home position adjustment procedures in this
section.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in home position adjustment mode. In either case, any
adjustments you made before the watch returned to the Timekeeping Mode will be
applied.
To adjust the home positions
1. Hold down C for about two seconds until the watch beeps twice and enters the
Timekeeping Mode.
2. Hold down D for about three seconds until the watch beeps.
@
••The watch is now in the home position adjustment
mode.
••The watch will exit the adjustment mode automatically
if you do not perform any o peration for about two or
three minutes.
••First is x Second Hand home position adjustment.
••If the x Second Hand moves to 12 o’clock, it is in the
correct home position. If it doesn’t, use D to move it
to 12 o’clock.
••Each press of C in the home position adjustment
mode will cycle through the adjustment settings as
shown below.
x Second
z Hour/ c Minute/ b 24-hour
m Day
n Right Dial Hands
v Left Dial Hand
3. After confirming that the x Second Hand is at the proper home position, press C.
This will switch to z Hour Hand and c Minute Hand home position adjustment.
••The z Hour Hand and c Minute Hand are at their proper home positions if
they both move to 12 o’clock. The b Lower Dial Hand also will move along with
z Hour Hand movement, and cannot be adjusted individually. If the hands are
not positioned correctly, use D (+) and B (–) to move them to their proper
home positions.
B
+
4. After confirming that the z Hour Hand and c Minute
Hand are in their correct home positions, press C.
This will switch to n Right Dial Hand home position
adjustment.
••The n Right Dial Hands are at their proper home
positions if they both move to 12 o’clock. If the hands
are not positioned correctly, use D (+) and B (–) to
move them to 12 o’clock.
■■The
hands and/or day indications are off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day alignment. Adjust the watch’s
hand and day home position alignment.
World Time Mode
■■The
World Time indicated by the n Right Dial Hands in the World Time Mode is
one hour off from the actual time in the selected time zone.
The STD (standard time)/DST (daylight saving time) setting of the selected World
Time City may be wrong. Select the correct STD (standard time)/DST (daylight saving
time) setting.
■■The
World Time indicated by the n Right Dial Hands in the World Time Mode
is off.
Your Home City setting may be wrong. Check your Home City setting and correct it,
if necessary.
Charging
■■The
watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3. Continue exposing the watch
to light until the x Second Hand starts moving normally (at one-second intervals).
x Second Hand starts moving at one-second intervals, but then suddenly
■■The
returns to move at two-second intervals.
The watch probably is not sufficiently charged yet. Continue keeping it exposed to
light.
Specifications
Accuracy at normal temperature: ± 15 seconds a month
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, 24-hour,
day, day of the week
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 29 city codes and Coordinated
Universal Time); Daylight Saving Time (summer time) / Standard Time
Stopwatch: Measuring capacity: 23'59.99"
Measuring unit: 1/100 second
Measuring mode: Elapsed time, split time
World Time: 29 cities (time zones) and Coordinated Universal Time
Other: Standard Time/Daylight Saving Time (summer time); Home City/World Time
City swapping
Alarm: Daily alarm
Other: Power Saving
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 6 months (no exposure to light after a full
charge; 10 seconds alarm beeper operation per day)
City Code Table
* 6
(FEN)
(RAI)
Pago Pago
Honolulu
Anchorage
Los Angeles
Denver
Chicago
New York
Santiago
Rio De Janeiro
Fernando de Noronha
Praia
UTC Offset/
GMT Differential
–11
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
(LON)
(PAR)
(ATH)
(JED)
(THR)
(DXB)
(KBL)
(KHI)
(DEL)
(DAC)
(RGN)
(BKK)
(HKG)
(TYO)
(ADL)
(SYD)
(NOU)
(WLG)
London
Paris
Athens
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
Hong Kong
Tokyo
Adelaide
Sydney
Noumea
Wellington
+1
+2
+3
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
City Code
>
6
5
5. After confirming that the n Right Dial Hands are in the
correct home positions, press C. This will advance to
v Left Dial Hand home position adjustment.
••The v Left Dial Hand is in the correct home position if
it is pointing at 12 o’clock. If it isn’t, use D (+) and B
(–) to move it to 12 o’clock.
6. After confirming that the v Left Dial Hand is in the
correct home position, press C. This will advance to
m Day home position adjustment.
••The m Day is in the correct home position if it
shows 1. If it doesn’t, use D (+) and B (–) to change
the day to 1.
7. Press A to return to the Timekeeping Mode.
••The m Day moves to the current day, and then the z Hour Hand and the
c Minute Hand move to the current time. Wait until everything stops moving.
Troubleshooting
Hand Movement and Position
■■I lost track of what mode the watch is in.
Refer to “To select a mode”. To return directly to the Timekeeping Mode from any
other mode, hold down C for about two seconds.
x Second Hand is moving at two-second intervals.
■■The
■■All
the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the x Second Hand starts moving
normally, at one-second intervals.
■■The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
••The watch is recovering from a sleep state.
••The watch is returning to the Timekeeping Mode automatically from the Alarm
Mode.
PAGO PAGO
HONOLULU
ANCHORAGE
LOS ANGELES
DENVER
CHICAGO
NEW YORK
SANTIAGO
RIO
F. DE NORONHA
PRAIA
UTC
LONDON
PARIS
ATHENS
JEDDAH
TEHRAN
DUBAI
KABUL
KARACHI
DELHI
DHAKA
YANGON
BANGKOK
HONG KONG
TOKYO
ADELAIDE
SYDNEY
NOUMEA
WELLINGTON
(PPG)
(HNL)
(ANC)
(LAX)
(DEN)
(CHI)
(NYC)
(SCL)
City
0
••Based
on data as of June 2009.
••The
rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
■■Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode. Do not perform any operation until the
hands return to their normal positions (in about 15 minutes). The hands should return
to their correct positions when normal operation returns. To help power recover, leave
the watch in a location where it is exposed to light.
■■The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it,
if necessary.
■■The current time setting is off by one hour.
Use the procedure under “To toggle the Home City time between standard time and
daylight saving time” to change the STD/DST setting.
4