Weber Fireplace User manual

® ®

FirePlace Assembly

Instructions

DANGER

Please read the following warnings carefully before using your FirePlace. Failure to follow these warnings may result in serious bodily injury or death, or in a fire causing damage to property.

䡵 The Weber FirePlace is designed solely for outdoor use. Indoor use can be lethal.

䡵

Use only on noncombustible surfaces, such as brick, flagstone, concrete, etc.

Do not use on a wooden deck.

䡵 Keep away from flammable materials, buildings and vehicles when in use.

䡵 Exercise the same care that you would with an open campfire.

䡵 Your Weber FirePlace is not to be used by children.

䡵 Keep away from flammable fluids such as gasoline, charcoal lighter fluid and alcohol, etc.

䡵 Keep children and pets away from the

FirePlace when in use.

䡵 Never wear loose-fitting or flammable clothing (such as nylon) when in use.

䡵 Do not overload. Before starting the fire make sure the lid is capable of closing.

Overloading can be dangerous if the lid cannot extinguish the fire.

䡵 Do not use soft woods, like pine or cedar.

Soft woods may "pop" and throw sparks.

䡵 Do not burn leaves, paper, plywood or trash in the Weber FirePlace.

䡵 Do not use volatile fluids, such as gasoline, charcoal lighter fluid or alcohol, to light or relight fires.

䡵 Use only sturdy, long-handled fireplace equipment, when adding or moving logs.

䡵 Do not attempt to move the FirePlace when in use or hot.

䡵 Use barbecue mitts when handling, because surfaces will be hot when in use.

WARNINGS

䡵 Fill the Weber FirePlace bottom with approximately two pounds of sand before use. This helps to insulate the bottom of the FirePlace.

䡵

Always extinguish fire with the lid. Do not douse with water; this will fracture the porcelain finish. Wood fires take a long time to extinguish. The Weber FirePlace and the ashes inside may remain hot for some time. Leave the lid closed until the

Weber FirePlace is cold.

䡵 Do not store the Weber FirePlace with combustible materials or ashes inside.

®

®

39935 10/93

Assembly

Tools needed

Screwdrivers, regular and Phillips

7/16 inch open-end or an adjustable wrench

Step 1

Check Package Contents

You should have received the parts shown below with your

Weber FirePlace. In the unlikely event a part is missing or damaged, do not return the FirePlace, instead contact:

Parts

WEBER-STEPHEN PRODUCTS COMPANY

Customer Service Center

250 South Hicks Road

Palatine, IL 60067-6241 (708) 705-8660

(800) 446-1071

Lid

Upper support ring

Four uprights

Lower support ring

Bottom

Two steel handles

Two top wood handles

Two bottom wood handles

Two wood screws

Sixteen large fiber washers

Eight small fiber washers

Twenty 1/4 inch steel washers

®

®

Twenty-four 1/4-20 hex nuts

Twenty-four 1/4-20 x 5/8 inch machine screws

Step 2

Install Steel Handles

You will need: lid, eight small fiber washers, eight steel washers, two steel handles, four machine screws, four hex nuts, a regular screwdriver and wrench.

Install handles as shown in Figure 1.

CAUTION: Do not overtighten; you may crack the porcelain finish.

Machine screw

Steel handle

Steel washer

Small fiber washers

Steel washer

Hex nut

Heat deflector

Four legs

Figure 1

Step 3

Install Wood Handles

You will need: lid assembly, two top wood handles, two bottom wood handles, two wood screws and a Phillips screwdriver.

Install handles as shown in Figure 2.

Wood screw

Top wood handle

Bottom wood handle

®

®

Step 5

Install Heat Deflector and Fourth Leg

You will need: heat deflector, bottom assembly, one leg, two machine screws, four large fiber washers, three steel washers, two hex nuts, a regular screwdriver and wrench.

Insert the heat deflector between the three legs and position it so it rests on all the leg tabs, as shown in Figure

4.

Now install the fourth leg using the procedure shown in

Figure 3, and making sure the heat deflector rests on all leg tabs.

Heat deflector

Figure 4

Figure 2

Step 4

Install Three Legs

You will need: three legs, bottom, six machine screws, twelve large fiber washers, nine steel washers, six hex nuts, a regular screwdriver and wrench.

Install only three legs as shown in Figure 3. Note that the machine screws are not installed in the same direction.

CAUTION: Do not overtighten; you may crack the porcelain finish.

Hex nut

Steel washer

Large fiber washer

Machine screw

Machine screw

Steel washer

Large fiber washer

Steel washer

Hex nut

Figure 3

Leg tab

Step 6

Assemble Upper Support Ring

You will need: four uprights, upper support ring, four machine screws, four hex nuts.

Assemble uprights as shown in Figure 5.

Machine screw

Hex nut

Step 8

Final Assembly

You will need: bottom assembly, ring assembly, lid assembly.

Place the ring assembly inside the FirePlace bottom with the lower support ring down. Figure 7.

Place the FirePlace lid on the upper support ring. It should rest on the upright tabs.

Figure 5

Step 7

Assemble Lower Support Ring

You will need: lower support ring, upright assembly, eight machine screws, eight hex nuts, a screwdriver and wrench.

Assemble lower support ring as shown in Figure 6.

Upper ring assembly from

Step 5

Lower support ring

Hex nut

Machine screw

Figure 6

Figure 7