Canon VB-H610D Installation guide

YT1-1637-000
Legal Notice
In some cases, camera monitoring may be prohibited by law or regulation, the details of which
differ by country or region. Before using the camera, check the laws or regulations of the country
or region where the camera is used.
* For the latest information (firmware and included software, user manuals, operating
environment, etc.), please refer to the Canon Web Site.
WARNING
o reduce a risk of fire or electric shock, do not expose this
T
product to rain or moisture.
Never try to install the camera yourself. Doing so may result in
unforeseen accidents such as dropping the camera or electric shock.
Write the serial number and MAC address of the camera (printed on the seal at the bottom of
the camera) in the field below before storing this Installation Guide in a safe location.
Serial number
_________________________________
MAC Address
_________________________________
© CANON INC. 2012
Check Included Items
Failure to do so may result in the camera falling or other accidents.
3. Safety wire
4. Audio interface cable
Symbols Indicating Camera Model
Camera specific functions will be listed using the icons below.
: VB-H610VE
: VB-H610D
: VB-M600VE
: VB-M600D
5. Template
for VB-H610D/
VB-M600D
for V
B-H610VE/
VB-M600VE
6. Dome case lock screw wrench
(VB-H610VE/VB-M600VE only)
7. Setup CD-ROM
8. Installation Guide (This document)
9. Warranty card
10. Notice
European Union (and EEA) only.
These symbols indicate that this product is not to be disposed of with your
household waste, according to the WEEE Directive (2002/96/EC), the Battery
Directive (2006/66/EC) and/or national legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in
accordance with the Battery Directive, this indicates that a heavy metal (Hg
= Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration
above an applicable threshold specified in the Battery Directive.
This product should be handed over to a designated collection point, e.g., on an authorized one-forone basis when you buy a new similar product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE) and batteries and accumulators.
Improper handling of this type of waste could have a possible impact on the environment and human
health due to potentially hazardous substances that are generally associated with EEE.
Your cooperation in the correct disposal of this product will contribute to the effective usage of
natural resources.
For more information about the recycling of this product, please contact your local city office, waste
authority, approved scheme or your household waste disposal service or visit
www.canon-europe.com/weee.
(EEA: Norway, Iceland and Liechtenstein)
Injury may result.
.
Recessed Mounting Kit SR600-VB
Junction Box Mounting Kit PS600-VB
This dedicated accessory is used to mount the camera to a junction box.
Heater unit HU600-VB
This dedicated accessory is attached to the interior of VB-H610VE/VB-M600VE to maintain
operation temperature within the dome and achieve stable operation even in extremely cold
environments.
A dedicated AC adapter for this camera.
This Installation Guide uses the following marks to indicate important information the
user should know in order to use the product safely. Be sure to observe these items.
Warning
Inappropriate handling against the instruction accompanied
by this sign may result in death or serious injury. Be sure to
observe these warnings to ensure safety.
Caution
Inappropriate handling against the instruction accompanied
by this sign may result in injury. Be sure to observe these
precautions to ensure safety.
Note
Inappropriate handling against the instruction accompanied by
this sign may result in property damage. Be sure to observe these
precautions.
This symbol indicates important or restricted items. Be sure to
read this section.
Contains reference information for operation or additional
explanations.
This section explains precautions that must be observed when using the camera. If they
are not observed, injury, death and/or property damage may occur. Read the following
information carefully and be sure to observe the precautions.
Installation Precautions
Warning
Do not install in the following places:
•Places in strong direct sunlight, near heat-generating objects, or subject to high
temperatures
•Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.)
•Humid or dusty places
•Places subject to oily smoke or steam
•Places subject to sea air
•Confined or enclosed places
Fire or electric shock may result.
R6
2(
R2
3- 4.6 ( 0.18)
(mounting screw holes)
.44
)
Day/Night Switch
Min. Subject Illumination
Day Mode (color)
120°
155
120°
( 6
.10)
Night Mode (monochrome)
12°
Junction Box Plate
4.2 (0.17)
14- 4.5 ( 0.18)
(Junction box fixing holes)
Precautions for Installing the Camera Outdoors (VB-H610VE/VB-M600VE)
When installing the VB-H610VE/VB-M600VE outdoors, observe the following precautions to retain
waterproof/dustproof capabilities.
•Be sure to install the camera under eaves or other places out of
direct sunlight.
•Install the camera in a place unexposed to long periods of direct
rainfall.
•When mounting the camera onto a wall or other upright surface,
position the wiring hole straight down to prevent rain infiltration.
•If wiring the camera through the wiring hole on the bottom, use
silicone sealant or a rubber mat to ensure waterproofing. Also
Position the
use an insect repellent sponge if necessary.
wiring hole
straight down
•If wiring with a composite pipe (NPT 3/4 inch threaded hole)
attached to the wiring hole, wrap teflon tape around the tip of the
pipe, clear any debris from the wiring hole and firmly tighten the
pipe. Apply silicone sealant after attaching the pipe.
•Firmly fix the dome case to the main unit of the camera with the lock screws, taking care not to
pinch cables between the main unit and dome case.
Focus
Shooting Distance (from front of lens)
Shutter Speed
Exposure
White Balance
46 (1-13/16)
83.5 (3-9/32)
85.7 (3-3/8)
Unit: mm (in.)
Metering Mode
Exposure Compensation
Smart Shade Control
AGC Limit
Pan Angle Range
Tilt Angle Range
Rotation Angle Range
Moving Speed
Precautions for Use
Warning
•If you discover defective conditions such as smoke, strange sounds, heat or strange
odors, immediately stop using the camera and contact your closest dealer.
Fire or electric shock may result from continued use of the product.
•Do not disassemble or modify the camera.
•Do not damage the connecting cable.
•Do not spill water or other liquid inside the camera, spray the camera with water, or
otherwise make it wet.
•Do not insert foreign objects into the camera.
•Do not use flammable sprays near the camera.
•Do not leave LAN cables, external power supplies or AC adapter (sold separately) power
connectors connected when the camera is not in use for long periods.
•Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning
the camera.
Fire or electric shock may result.
Warning
•Only use the dedicated AC Adapter PA-V17 (sold separately) for AC power.
•Do not set any heavy objects on the power cable.
•Do not pull, forcibly bend, scratch, or modify the power cable.
•Do not cover or wrap the AC adapter (sold separately) with cloth or blankets.
Fire or electric shock may result.
Be sure to read the user manual for the PA-V17 (sold separately) before use.
Caution
•After turning off the power, wait for at least five seconds before turning the power on
again. If the power is turned on again too quickly, the camera may operate poorly.
1/3 type CMOS (primary color filter)
Approx. 2.1 million pixels
Approx. 1.3 million pixels
Progressive
3x optical (4x digital) zoom lens (electric drive)
3x optical zoom lens (electric drive)
2.8 (W) – 8.4 mm (T)
F1.2 (W) – F2.0 (T)
Horizontal: 111.0° (W) – 36.5° (T)
Vertical: 60.1° (W) – 20.5° (T)
Horizontal: 101.2° (W) – 33.7° (T)
Vertical: 74.7° (W) – 25.3° (T)
Auto/Manual
Network Terminal
LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
Audio Input Terminal
(common for LINE IN & MIC IN) Connect via an audio interface cable (included)
Switch LINE IN/MIC IN in the setting page.
LINE IN x 1 (connect to an amplifier microphone) or
MIC IN x 1 (connect to a microphone w/o amplifier)
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
Audio Output Terminal
(LINE OUT)
Connect via an audio interface cable (included)
LINE OUT x 1 (connect to an amplifier speaker)
External Device I/O Terminal
Input x 2, Output x 2
Memory Card
SD Memory Card, SDHC Memory Card, SDXC Memory Card*4 Compatible.
Capacity: Max. approx. 32 GB
Frame Rate: Max. 1 fps
.3 lux (F1.2, shutter speed 1/30 sec., when smart shade control is
0
off, 50IRE)
0.02 lux (F1.2, shutter speed 1/2 sec., when smart shade control is
off, 50IRE)
0.008 lux (F1.2, shutter speed 1/2 sec., when smart shade control
is on, 50IRE)
0.25 lux (F1.2, Shutter Speed 1/30 sec., when Smart Shade Control
is off)
0.07 lux (F1.2, Shutter Speed 1/8 sec., when Smart Shade Control
is off)
0.018 lux (F1.2, Shutter Speed 1/8 sec., when Smart Shade Control
is on)
0.015 lux (F1.2, shutter speed 1/30 sec., when smart shade control
is off, 50IRE)
0.001 lux (F1.2, shutter speed 1/2 sec., when smart shade control
is off, 50IRE)
0.0005 lux (F1.2, shutter speed 1/2 sec., when smart shade control
is on, 50IRE)
0.008 lux (F1.2, Shutter Speed 1/30 sec., when Smart Shade
Control is off)
0.002 lux (F1.2, Shutter Speed 1/8 sec., when Smart Shade Control
is off)
0.001 lux (F1.2, Shutter Speed 1/8 sec., when Smart Shade Control
is on)
One-shot AF/Manual/Fixed at infinity
Day Mode: 0.3 m (12 in.) – infinity
Night Mode: 1.0 m (3.3 ft.) – infinity
1, 1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/16000*4 sec.
Auto/Auto (Flickerless)/Auto (Shutter-priority AE)/Manual (Shutter Speed, Aperture,
Gain)
Auto/Light Source (Daylight Fluorescent/White Fluorescent/Warm Fluorescent/
Mercury Lamp/Sodium Lamp/Halogen Lamp)/Lock (One-shot WB)/Manual
Center-Weighted/Average/Spot
9 levels
7 levels
7 levels (increases the brightness of shaded subjects in a video)
5 levels
350° (±175°)
150° (±75°)
350° (±175°)
Pan: 19.2°/sec., Tilt: 14.2°/sec., Rotation: 43.7 °/sec.
When the Camera Angle Setting Tool is used
Others
Operating Environment
Power Supply
Power Consumption
Dimensions
Weight
Impact Resistance
Dust-resistant/
Waterproof Specification
Temperature: -10°C – +50°C (+14°F – +122°F), Humidity: 5% – 85% (without
condensation)
Temperature: -30°C – +50°C (-22°F – +122°F), Humidity: 5% – 85%
(without condensation)*
*Equipped with separately sold Heater Unit HU600-VB
PoE:PoE power supply via LAN connector (IEEE802.3af compliant)
AC Adapter: PA-V17 (100 – 240 V AC) (sold separately)
External power source: 24 V AC/12 V DC
Heater Unit HU600-VB (sold separately): 24 V AC only
Max. approx. 8.4 W
Max. approx. 7.8 W
When using PoE: Max. approx. 8.6 W
Max. approx. 10.72 W
When using AC Adapter PA-V17: Max. approx. 10.2 W
Max. approx. 10.9 W
Max. approx. 9.0 W
Max. approx. 8.3 W
When using DC: Max. approx. 9.0 W
Max. approx. 8.1 W
Max. approx. 7.5 W
When using AC: Max. approx. 8.3 W
Max. approx. 18.7 W*
Max. approx. 18.9 W*
*when separately sold Heater Unit HU600-VB installed
( x H) 180 x 147 mm ( 7.09 x 5.79 in.)
( x H) 186 x 140 mm ( 7.32 x 5.51 in.)
Approx. 1920 g (4.24 lb.) (camera only)
Approx. 162 g (5.8 oz.) (Junction Box Mounting Kit)
Approx. 1910 g (4.22 lb.) (camera only)
Approx. 162 g (5.8 oz.) (Junction Box Mounting Kit)
Approx. 1200 g (2.65 lb.) (camera only)
Approx. 159 g (5.7 oz.) (Junction Box Mounting Kit)
Approx. 1200 g (2.65 lb.) (camera only)
Approx. 159 g (5.7 oz.) (Junction Box Mounting Kit)
External materials: aluminum alloy, Dome: polycarbonate plastics
With lens shock absorbing mechanism
Estimated shock resistant: 50J (based on Canon’s test method)
IP66-rated (IEC60529)
Only applies if properly installed and adequately waterproofed
*1 (W): maximum wide angle, (T): maximum telephoto
*2 T
he frame rate may be reduced due to Viewer PC’s specs, the number of clients accessing at the same time,
network loads, image quality setting, type or movement of the subject or other reasons.
*3 A third-party amplifier speaker is necessary.
*4 VB-H610VE/VB-H610D specific function
Server
Video Compression Method
Video Size
Notes on Power Supply
Safety Precautions
VB-H610D/VB-M600D
3/4” NPT threaded hole
•Do not install the camera on an unstable surface.
•To maximize shock resistant specifications, do not install on insufficiently strong
surfaces or surfaces subject to significant vibration (VB-H610VE/VB-M600VE).
•Take measures to remove static electricity before performing any procedures.
Damage to peripheral items may result.
Accessories can be purchased separately as necessary.
Caution
•Take care not to damage wiring or pipes in the room.
Accessories
Important
•Do not touch the edge of metal parts with bare hands.
•Be careful not to trap your fingers during installation of the camera.
Malfunction may result.
Caution
7.5°
6.
46
)
0°
•Installation Guide (This document)
This guide provides notes on camera installation and explains the procedures to install the
camera onto a ceiling or wall.
•Operation Guide (Included in the Setup CD-ROM)
This document explains the initial camera settings, Admin Tools settings, viewer operations
and troubleshooting, etc.
Symbols Indicating Safety Precautions
This product comes with the following items. If any item is missing, contact the dealer where you
purchased the product.
2. Power connector
1. Camera
(VB-H610VE/VB-H610D/
VB-M600VE/VB-M600D)
(
Image Sensor
Number of Effective Pixels
Scanning Method
Lens
Focal Length*1
F-number
Viewing Angle
12
User Manuals
AC Adapter PA-V17
Printed in Taiwan
16
4
3- 4.6 ( 0.18)
(mounting screw holes)
•Do not install in unstable places, places subject to significant vibration or impact, or
places subject to salt damage or corrosive gas.
•Be sure to attach the safety wire when installing the camera.
This dedicated accessory is used to install the camera recessed into a wall or ceiling.
CautionRequest a professional installer for all camera installation work.
R6
2(
R2
.44
)
85.7 (3-3/8)
Thank you for purchasing Canon Network Camera VB-H610VE/VB-H610D/VB-M600VE/VB-M600D
(hereafter referred to as the camera).
VB-H610D/VB-M600D is designed for indoor use only. It is also possible to install the VB-H610VE/
VB-M600VE outdoors, such as underneath eaves.
Be sure to read “Installation Guide” (this document) and “Operation Guide” (included in the Setup
CD-ROM) before use.
This “Installation Guide” explains the installation method for installing the camera on a ceiling or
wall and the installation method using the separately sold junction box mounting kit PS600-VB. Be
sure to read the “Safety Precautions” section for correct use. After reading this Installation Guide,
keep it in a readily accessible location for future reference.
For the installation of this camera recessed into a ceiling or wall using the recessed mounting kit
(sold separately), please read the “Recessed Mounting Kit SR600-VB Installation Guide” included
with the recessed mounting kit.
When using the heater unit (sold separately), please read the “Heater Unit HU600-VB User
Manual” included with the heater unit.
The detailed procedures for using this camera are explained in the “Operation Guide”. Read
these guides carefully before using the camera to ensure correct use.
Interface
Camera
VB-H610VE/VB-M600VE
°
120
Installation Guide
•This installation should be made by a qualified service person and should conform to
all local codes.
•When installing on a ceiling, make sure the surface is capable of withstanding the total
weight of the camera and ceiling plates and is sufficiently reinforced if necessary.
•Periodically check the parts and screws for rust and to see if they have loosened, in
order to prevent injuries and equipment damage due to falling items.
Main Specifications
46 (1-13/16)
/
For installation or inspection of this camera, consult the dealer where you purchased
the product.
External Dimensions
83.5 (3-9/32)
/
Caution
147 (5.79)
When using the camera (for video or audio recording), it is the full responsibility of the user to
protect privacy and avoid any violation of publicity rights. For example, obtain consent to install
the camera in advance if specific buildings or rooms are to be monitored. Canon shall have no
liability whatsoever in this regard.
Network Camera
/
Notes on Privacy and Publicity Rights Regarding the Use of Video/Audio
140 (5.51)
ENGLISH
JPEG, H.264
J PEG: 1920 x 1080, 960 x 540, 480 x 270, 320 x 240
H.264: 1920 x 1080, 960 x 540, 480 x 270
JPEG: 1280 x 960, 640 x 480, 320 x 240, 160 x 120
H.264: 1280 x 960, 640 x 480, 320 x 240
Video Quality
JPEG, H.264: 5 levels
JPEG: 0.1 – 30 fps
Frame Rate*2
H.264: 1/2/3/5/6/10/15/30 fps
H.264: 10/15/30 fps
1920 x 1080 (when streaming): 30 fps
Max. Frame Rate
1280 x 960 (when streaming): 30 fps
0.5/1/1.5/2/3/4/5 sec.
I-Frame Interval
Simultaneous Client Access
Max. 30 Clients + 1 Admin Client
H.264: Max. 10 Clients
Camera Control
Administrator, Authorized user, Guest user (level of control varies depending on
user)
Max. 50 user names and passwords registered for authorized users.
Access Control
User authority (user name and password), Host Access Restrictions (IPv4, IPv6)
Encrypted Communications
SSL/TLS, IPsec (Auto Key Exchange/Manual)
Protocol
IPv4: TCP/IP, UDP, HTTP, FTP, SNMP (MIB2), SMTP (Client), DHCP (Client), DNS
(Client), ARP, ICMP, POP3, NTP, SMTP authentication, RTSP, WV-HTTP
(Canon proprietary), ONVIF
IPv6: TCP/IP, UDP, HTTP, FTP, SMTP (Client), DHCPv6 (Client)*4, DNS (Client),
ICMPv6, POP3, NTP, SMTP authentication, RTSP, WV-HTTP (Canon
proprietary), ONVIF
Available
AutoIP
Audio Compression Method
G.711 µ-law (64 kbps)
Audio Communication Method Full-duplex (two-way) Echo cancellation function compliant
Sound Transfer Protocol by Canon
Available (audio files can be played back when an event is triggered by the
Audio File Playback*3
intelligent function or external device input.)
Privacy Mask
Number of registration: Max. 8 places, Number of mask colors: 1 (select from 9
colors)
Max. 20 positions (Preset Tour capable)
Preset
Intelligent Function
<Video>
Detection Types: moving object detection, abandoned object detection,
removed object detection, camera tampering detection, and passing detection*4
Detection Settings: Max. 15
<Volume>
Volume Detection
Event Trigger Type
External Device Input, Intelligent Function (Video), Intelligent Function (Volume),
Timer
Image Upload
FTP/HTTP/SMTP (e-mail)
Temporary storage memory in camera :
Max. approx. 5 MB
Max. approx. 4 MB
Frame Rate: Max. 10 fps
Event Notification
HTTP/SMTP (e-mail)
Digital PTZ Cropping sizes : 640 x 360/512 x 288/
Image Cropping Function
384 x 216/256 x 144/128 x 72
On-Screen Display
Available
Available
Daylight Saving Time
Language
English/German/French/Italian/Spanish/Japanese
The contents of this guide are subject to change without any prior notice.
“ONVIF” is a trademark of ONVIF Inc.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON EUROPA N.V.
Bovenkerkerweg 59-61, P.O. Box 2262, 1185 XB Amstelveen, The Netherlands
Installing the Camera
Use the junction box plate (included with the
separately sold junction box mounting kit PS600Mounting hole (inner side)
VB) to mount the camera to the junction box.
Mounting hole (outer side) 1 Attach the junction box plate to the junction
box with screws that match the screw holes
in the junction box.
2 Guide the cables through the wiring hole and
Junction box plate
mount the camera to the junction box plate
using the 3 included camera fixing screws
(M4).
The camera fixing screws differ in length
Camera fixing screw (included)
depending on the camera. Use short screws
Short screw x 3
for VB-H610D/VB-M600D, and long screws
Long screw x 3
for VB-H610VE/VB-M600VE.
3 Wire the cables and attach the inner cover
Dome case
and dome case.
fixing screw x 3
The following describes procedures for mounting the camera to a ceiling.
Before installing the camera, set the IP address and other network information on the camera
using the “VB Initial Setting Tool” on the Setup CD-ROM.
For details on how to operate the “VB Initial Setting Tool”, see “Operation Guide”.
Lock screw
holes
1 Determine an installation position for the camera and drill holes in the ceiling
Use the included template to determine the positions of the fixing screw holes and wiring hole
( 40 mm ( 1.6 in.)) according to the camera orientation. Next, cut out the wiring hole, and drill
the fixing screw holes in the the ceiling.
Dome case
2 Loosen the three lock screws on the dome case and remove the dome case
3
Part Names
Connecting the Camera
Dome Case/Inner Cover/Camera
Power Connection
Using a Junction Box
Special temper-resistant screws are used for the dome case lock screws. Use the included
dome case lock screw wrench.
Power can be supplied to the camera in the three ways described below.
 PoE (Power over Ethernet)
Inner cover
•Some PoE HUBs have total consumption current limits for ports, which can interfere with performance
when multiple ports are in use. For more information, check the instruction guide for your PoE HUB.
•Use a category 5 or higher cable 100 m (328 ft.) or less in length for the LAN cable that connects the
camera and the PoE HUB.
* Diagram of VB-H610VE.
Using an SD Memory Card
Inserting the card
7
Lens (Electric Drive)
SD card slot
 External Power Supply
Push the SD memory card in all the way until the card slightly
pops out. Pinch the card and remove.
5 Secure the safety wire
12 V DC or 24 V AC input can be used.
Connect the included power connector as shown below.
Camera
Wiring hole
Screwdriver
Tightening torque: 0.2 N·m (max.)
•Insert the SD memory card before attaching the dome case.
Bottom
•Make sure the SD memory card is not write-protected.
6 Guide the LAN cable through the wiring hole
External Device I/O Terminals
Cable tie
Important
Power connector
(included)
Attaches the included
safety wire.
For VB-H610VE/VB-M600VE, secure the various cables with the cable clamps fastened to the
camera to prevent damage to cables or connectors due to vibration, etc.
*The diagram is a wiring example for VB-H610VE/VB-M600VE.
The camera's serial number. Write the number
on the front of this Installation Guide before
installing the camera.
Wiring hole
MAC address
The camera's unique address. Write the address
on the front of this Installation Guide before
installing the camera.
Audio interface cable
(included)
External Device I/O cable
Power cable
Wire the cables referring to “Cable Wiring Method”.
Heater cable
Loosen the screw and rotate the
cable clamp. Bend the cable clamp
as shown in the diagram before
wiring the cables.
9 Attach the inner cover
Cable clamp
(VB-H610VE/
VB-M600VE only)
22
20
18
16
0.52
( 0.020)
0.65
( 0.026)
0.82
( 0.032)
1.03
( 0.041)
1.30
( 0.051)
12 V DC maximum cable lengthm
(ft.)
5
(16.4)
9
(29.5)
14
(45.9)
23
(75.5)
32
(105.0)
24 V AC maximum cable lengthm
(ft.)
11
(36.1)
18
(59.1)
29
(95.1)
46
(150.9)
64
(210.0)
Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.
 AC Adapter
•When using the heater unit HU600-VB (sold separately), use 24 V AC for the VB-H610VE/VB-M600VE
power supply. PoE, 12 V DC and the AC adapter cannot be used.
External Device I/O Terminals
Bend the cable clamp to
grip the cables.
External device I/O terminals consist of two input and output systems each. Viewer can be used
to check external device input status and control output to an external device (see “Operation
Guide” > “Selecting the External Device Output” and “Displaying Event Status”).
 External Device Input Terminals (IN1, IN2)
Tighten the screw to fix the cable
clamp and bend the cable clamp to
grip the cables.
Firmly bend the cable clamp so that
it does not come into contact with the
inner cover.
Firmly fix the dome case at three points to the camera using the dome case screws.
Cutout section
Camera
Important
When attaching the dome case, be sure not to pinch cables between the camera and dome case. Pinched
cables may impair dust and waterproofing capabilities.
11 Set the camera angle
* Illustrations without icons are examples of VB-H610D/VB-M600D.
24
Conductor diameter mm
(in.)
•When the camera needs to be rebooted, perform the reboot operation from the camera setting page
(see “Operation Guide” > “Setting Page” > “Maintenance”).
10 Attach the dome case
Dome case
Cable (AWG)
•The camera does not have a power switch. Connecting and disconnecting the LAN cable (PoE power
supply), AC adapter, or external power supply plug turns the power ON and OFF, respectively.
Attach the inner cover to its original position.
10
Recommended Power Cables [Reference]
Use the dedicated AC Adapter PA-V17 (sold separately).
Cable clamp (VB-H610VE/VB-M600VE only)
When wiring is complete, seal the wiring hole to keep out insects and dust.
If the cables cannot be stored above a ceiling made
of concrete, etc., break the cutout section of the dome
case using diagonal pliers to create a cutout through
which to guide the cables.
When installation is complete, use the Camera Angle Setting Tool to adjust the pan, tilt,
rotation, zoom (and focus) see “Operation Guide” > “Camera Angle Setting Tool”).
External device
Output terminal
OUT1, OUT2
Audio Input/Output Terminals
Each audio input/output terminal has one input system and one output system.
Connecting the camera to an audio input/output device such as a microphone or a speaker with
an amplifier allows you to send/receive audio through the viewer.
Use the included audio interface cable to connect audio input/output devices to the camera.
Use the 3.5 mm ( 0.14 in.) monaural mini-jack connector to connect an audio output device with
the audio interface cable.
OUT
The long end (has cable marker) from the bifurcation point in the
cable corresponds to the audio output terminal. The short end
(does not have cable marker) from the bifurcation point in the cable
corresponds to the audio input terminal.
 Audio Input Dual LINE IN/MIC IN (monaural input)
Although the camera has a single audio input system, it supports two types of microphone input:
LINE IN and MIC IN. Before using the audio input, change the [Audio Input] on the Setting Page
(see “Operation Guide” > “Audio Input”). LINE IN is selected by default.
Input terminal: 3.5 mm ( 0.14 in.) mini-jack (monaural)
•Dynamic MIC IN
Input impedance: 1.75 kΩ ± 20%
* Supported microphones: Output impedance: 400Ω – 600Ω
•Condenser MIC IN
Input impedance (microphone bias resistance): 2.2 kΩ ± 20%
Microphone power supply: plug-in power (voltage: 1.8 V)
* Supported microphones: Condenser microphones with plug-in power support
•LINE IN
Input level: Max. 1 Vp-p
* Use a microphone with an amplifier.
 Audio Output Terminal LINE OUT (monaural output)
Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from Viewer.
Output terminal: 3.5 mm ( 0.14 in.) mini-jack (monaural)
Output level: Max. 1 Vp-p
* Use a speaker with an amplifier.
Note
8 Wire the cables
Important
•24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or
60 Hz ±0.5 Hz or less)
Current supply capacity of at least 1.0 A per camera
•For an external power supply, use a double-insulated device.
Top view of the camera interior
Fix the camera at three points to the ceiling using the appropriate screws. Three 4.5 mm
( 0.18 in.) ceiling fixing screw holes are located on the camera. You must provide screws that
correspond to the ceiling fixing screw holes.
Adaptive wiring for external device cables
Solid conductor AWG: No. 28 – 22
Conductor size: 0.32 – 0.65 mm ( 0.013 – 0.026 in.)
Cable strip should be approx. 8 – 9 mm (0.31 – 0.35 in.).
•The power supply should be within the following voltage range.
•When using a 12 V DC battery power supply, be sure to connect
resistors of at least 0.5 – 1.0 Ω/20 W in series to the power line.
LAN cable
7 Fix the camera to the ceiling
Note
Input terminal
IN1, IN2
External device
0.1 µF
IN
•12 V DC: Voltage fluctuation within ±10% of 12 V DC
Current supply capacity of at least 1.5 A per camera
Serial number
Heater unit HU600-VB
(sold separately for
VB-H610VE/VB-M600VE)
The load connected to the output terminals should be within the following rating range.
Rating between output terminals:
Internal Connection Diagram
Maximum voltage 50 V DC
+3.3 V
Continuous load current at or below 100 mA
1 kΩ
10 kΩ
10 kΩ
On resistance: Max. 30Ω
Important
Safety wire attachment
Cable Wiring Method
For 12 V DC and 24 V AC input, use a power supply insulated
from 100 V AC.
12 V DC can be connected in a non-polar configuration.
Wiring hole
Approx. 4 to 6 mm
(0.16 to 0.24 in.)
Securely attach the safety wire to an anchor or structure. After securing one end of the safety
wire to the ceiling, secure the other end to the camera using the screw that is fastened to the
camera.
External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets
have no polarity. Controls from the viewer can be used to open and close the circuit between the
terminals. Using optical couplers, the output terminals are isolated from the camera's internal
circuit.
Cable marker
Strip
•When using an SD memory card with the camera for the first time, it is recommended to format the card
after inserting it into the camera (see “Operation Guide” > “Setting Page” > “Memory Card”).
When using the AC Adapter PA-V17 (sold separately), cut the cable tie and
remove the ferrite core. Be sure not to damage the power cable when cutting
the cable tie.
9
•The camera can also be connected to an AC adapter (sold separately) while receiving power from
a PoE HUB. In such cases, the PoE power supply is given priority, and the camera does not use the
power supply from the AC adapter (sold separately). When the PoE power supply is disconnected,
power is supplied automatically from the AC adapter (sold separately). Midspan (a LAN cable power
supply device) is a device that, like a PoE HUB, supplies power to the camera via a LAN cable.
Removing the card
When using an external power supply, guide the power interface cable through the wiring
hole. Guide the I/O interface cable and the audio interface cable (included) through the wiring
hole if necessary.
5
•When the camera is connected to a switching HUB, changing the connection while the camera is
operating may cause the HUB learning function to interfere with communication. Do not change the
connection when the camera is operating.
Push the SD memory card as far as possible into the SD card
slot with the label facing outward.
4 Open the wiring hole according to the installation method
Use a coin to unscrew the wiring hole cover from the side through which cables will be
guided. Screw the wiring hole cover into the other wiring hole. You can fit a composite pipe
(NPT 3/4 inch threaded hole) to the wiring hole.
When guiding cables through
the ceiling wiring hole
•Check with your dealer for more information about PoE HUB and Midspan technology.
•Some PoE HUBs allow current limits for each port, but applying limits may interfere with performance. If
using this type of PoE HUB, do not limit the operating current.
Important
When guiding cables through
the side
Important
Dome case
Lock screw
Inner cover
Use a box cutter to cut a cross shape into the wiring hole cover in order to guide cables
through. Do not remove the wiring hole cover.
4
The camera supports PoE functions. Power can be supplied to the camera by using a LAN cable
to connect it to a PoE HUB that conforms to the IEEE 802.3af standard.
Dome case
3 Remove the tape and the inner cover
Remove the 4 pieces of tape that prevent lens rotation during shipping, and push the inner
cover in the direction of the arrows to remove it. Then remove the 2 pieces of tape attached to
the base of the lens.
 External Device Output Terminals (OUT1, OUT2)
Internal controller
2
Bend the cable clamp so that
it does not exceed this height
Cable clamp
Inner cover
1 Reset switch
Turn on the power while pushing this switch using a sharp object. Continue to push the switch for 5
seconds or more to restore all factory settings except for the date and time.
2 LED
The blue LED light comes on.
On: When powered on, during reboot
Off: During normal use
3
4
5
6
SD card slot
External device I/O terminals
Power connection terminal
Installation screw holes
Used when securing the camera to the installation surface, the junction box mounting kit (sold separately),
or the recessed mounting kit (sold separately).
7 Wiring hole
8 Audio I/O terminal
Connect the included audio interface cable here to connect audio input and output devices to the camera.
9
A
q
A
a
A
s
100BT LAN connector
Cable clamps
Fan
Heater connection terminal
External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative
terminals connected to the camera interior GND. Connecting cables to the positive and negative
terminals and opening or closing the circuit notifies the Viewer.
Important
•When connecting sensors and switches, connect terminals that are electrically isolated from the
respective power and GND.
•Do not push the external device I/O terminal button with too much force. Doing so may cause the button
to remain pushed-in.
Important
•Using the wrong settings in [Audio Input] may damage the camera and/or microphone. Be sure to
configure settings correctly.
•Microphone characteristics may affect volume and sound quality.
•Audio may be interrupted depending on PC characteristics and network environment.
•Video and audio can be streamed to up to 30 clients. However, audio may be interrupted when
streaming to many clients or using SSL.
•Audio may be interrupted when using antivirus software.
•Connecting and disconnecting the LAN cable interrupts the audio. Use the viewer to reconnect.