User manual | Shure BG 4.1 Microphone User Guide

Add to my manuals
2 Pages

advertisement

User manual | Shure BG 4.1 Microphone User Guide | Manualzz
MODEL BG4.1
UNIDIRECTIONAL CONDENSER MICROPHONE
The BG4.1 microphone utilizes an advanced condenser
transducer design for use in professional instrument sound reinforcement and project studio recording. Its electret cartridge
has a wide frequency response for natural sound reproduction,
and its high sensitivity and low noise make it an ideal choice
for producing quality demo tapes. The BG4.1 also maintains
a cardioid polar pattern throughout its frequency range which
ensures high gain-before-feedback and maximum isolation
from undesired sound sources. Operating voltage is supplied
by phantom power from a mixer, or an internal AA battery for
10,000 hours of continuous use. Typical applications for the
BG4.1 include acoustic guitar, drums, stringed instruments,
and vocals (when mounted on a stand).
GENERAL RULES FOR MICROPHONE USE
1. For optimal signal-to-noise ratio, place the microphone as
close as possible to the desired sound source.
2. For the best gain-before-feedback and isolation from undesired background noise, aim the microphone toward the
sound source and away from undesired sound sources
(Figure 1). The BG4.1 features a cardioid polar pattern
which is most sensitive to sound directly in front of the microphone, and least sensitive to sound directly at 180 .
3. For the purest reproduction of sound, use only one microphone per sound source and use the fewest number of microphones necessary for the application.
4. For maximum isolation, keep the distance between microphones at least three times the distance from each source
to its microphone.
5. Placing the microphone close to the sound source improves
bass response (Figure 2). This phenomenon is known as
proximity effect and can be used to achieve a fuller sound,
and to change the bass output of an instrument without using tone controls. Proximity effect is also especially good
for vocals during soft passages where emphasis is needed.
6. Placing the microphone too close to acoustically reflective
(smooth, hard) surfaces will result in a poor frequency response and will increase the chances for feedback. To minimize this effect, place microphones as far as possible from
acoustically reflective surfaces.
7. Add an external windscreen when using the microphone
outdoors to reduce wind noise.
8. It is important to keep foreign particles out of the grille and
the windscreen because they may alter the frequency
response of the microphone. Also, avoid exposing conSPECIFICATIONS
Type
Condenser (electret bias)
Frequency Response
40 to 18,000 Hz (Figure 2)
Polar Pattern
Cardioid (unidirectional), symmetrical about axis
(Figure 3)
Output Impedance
600 Ω
Recommended Input Load Impedance
800 Ω minimum
Output Level (at 1,000 Hz)
Open Circuit Voltage . . . . . . . . . . . –48.0 dBV/Pa (4.0 mV)
1 Pascal=94 dB SPL
Maximum SPL
2,000 Ω load . . . . . . . 131 dB (phantom), 127 dB (battery)
800 Ω load . . . . . . . . 129 dB (phantom), 126 dB (battery)
2
Output Noise
20 dB typical, A weighted
24 dB typical, weighted per DIN 45 405
Dynamic Range (maximum SPL, 2 kΩ load, to A-weighted
noise level)
111 dB (phantom); 107 dB (battery)
Polarity
Positive pressure on diaphragm produces positive voltage
on pin 2 relative to pin 3 of microphone output connector
Power
Phantom
Supply Voltage . . . . . . . . . . . . . . . . . . . 11 to 52 Vdc
Current Drain . . . . . . . . . . . . 2.0 mA max at 52 Vdc
Reverse polarity protected to . . . . . . . . . . . 100 Vdc
Battery
Recommended . . . . . . . . . . . 1.5 V alkaline AA size
(NEDA 15A)
Life . . . . . . . . . . . . . . . . . . . . . . . . up to 10,000 hours
Environmental Conditions
This microphone will operate over a temperature range of –29
to 57o C (–20 to 135o F), and at relative humidity of 0 to 95%.
Switch
Built in On/Off switch
Connector
3-pin male XLR connector designed to mate with Cannon
XL series, Switchcraft A3 (Q.G.) series, or equivalent
connector
Case
Steel and brass construction with black painted finish
Dimensions
See Figure 4
Net Weight
250 g (8.8 oz) less battery
Certification
Eligible to bear CE Marking. Conforms to European EMC
Directive 89/336/EEC. Meets applicable tests and performance criteria in European Standard EN55103 (1996) parts
1 and 2, for residential (E1) and light industrial (E2) environments.
FURNISHED ACCESSORIES
Swivel Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A25D
Padded Carrying Case . . . . . . . . . . . . . . . . . . . . . . . . . . 26A16
OPTIONAL ACCESSORIES
Phantom Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . PS1A
Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3WS
7.6 m (25 ft.) Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C25J
The BG4.1 is backed by the Shure 2-year warranty. For
service or parts information, please contact the Shure Service
department at 1–800–516–2525. Outside the United States,
please contact your authorized Shure Service Center.
3

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement