Miele KM89-2 Operating instructions

Operating instructions for the
KM 89-2 Deep Fryer
]ö
M.-Nr. 03 999 350
Description of the appliance
Description of the appliance
4
3
2
5
1
6
7
11 10 9 8
2
Description of the appliance
Description of the appliance
b Control panel
c Basket handle (fold-away, removable)
d Frying basket
e Lid
f Heating element hinge with basket
hanging support
g Heating element
h Power cord
i Drain valve
j On/Off and temperature control
k Heating indicator lamp = (yellow)
l Operation indicator lamp = (white)
Data plate
Because the data plate is no longer
visible once the appliance has been installed, a 2nd data plate is supplied. It
should be placed into the space provided on page 13 of these instructions.
3
Contents
Contents
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Help protect our environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Warning and Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Frying
Turning on the Fryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Check the oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Correct procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
After frying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Draining the oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Frying chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
After Sales Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installation instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Help protect our environment
Help protect our environment
Disposal of packaging materials
The transport and protective packing is
mostly manufactured from the following
re-usable materials:
. . . Corrugated paper / cardboard mostly from recycled materials.
. . . Polyethylene foil (PE) partly from secondary raw materials.
Rather than throwing these materials
away, please take them to the nearest
recycling center for specific waste.
Disposal of your old machine
Old machines contain materials which
can be recycled. Please contact your
local recycling center or scrap merchant about potential recycling programs, before disposing of the appliance.
Read the notes on page 5 before disposing of the appliance.
5
Warning and Safety Instructions
Warning and Safety Instructions
When using your Deep Fryer, follow
basic safety precautions including
the following:
Read all instructions before using
for the first time.
Use the appliance only for its intended purpose.
Be sure your appliance is properly
installed and grounded by a qualified technician or electrician.
Before servicing, disconnect the
power supply by removing the fuse
or tripping the circuit breaker.
The electrical safety of this appliance can only be guaranteed
when continuity is complete between
the appliance and an effective grounding system.
It is imperative that this basic safety requirement is met. If there is any doubt,
have the electrical system of the house
checked by a qualified electrician. The
manufacturer cannot be held responsible for damage caused by the lack or
inadequacy of an effective grounding
system.
Do not connect the appliance to
the main electric supply using an
extension cord. Extension cords do not
guarantee the required safety of the appliance.
Never use the Fryer to warm or
heat the room.
When using an electrical outlet
near the Fryer, make sure that the
cable does not come into contact with
the heating element of the Fryer.
6
Do not allow children to operate or
play with or near the Fryer.
Use extreme caution when lifting
the basket or disposing of hot
grease.
Keep all toys stored away from the
Fryer to prevent injury to curious or
playful children.
Please remember that, in use, the
Fryer becomes hot; therefore, ensure that children do not touch it.
Do not store items on the Fryer
when not in use.
Do not let cooking grease or other
flammable materials accumulate
on the appliance. Make certain there is
no open flame present when adding oil
to the Fryer.
Allow sufficient time for the appliance to cool before touching or
exposing surface areas to flammable
materials.
Always cook pork thoroughly to ensure that, in the event of trichina,
all bacteria will be killed and the meat
is safe to eat.
Never leave the appliance unattended when cooking with oil or
fat. Very hot oil can cause a fire.
Wear proper apparel – Loose-fitting
or hanging garments should never
be worn while using the appliance.
Warning and Safety Instructions
Warning and Safety Instructions
Repairs on electrical appliances
should only be performed by qualified personnel. Do not repair or replace
any part of the appliance unless specifically recommended in this manual.
Do not use water on grease fires.
Smother any fire or flame or use a
dry chemical or foam-type extinguisher.
Use only dry potholders. Moist or
damp potholders used on hot surfaces can result in steam burns. Do not
let the potholder touch the hot heating
elements. Do not use a towel or other
bulky item near the appliance.
Do not store items of interest to
children in cabinets above or behind the Fryer – children climbing on
the Fryer to reach these items could be
seriously injured.
This appliance should only be operated after being correctly installed.
Always ensure food is sufficiently
cooked or reheated.
Many factors affect overall cooking
time, including the size and amount of
food, its temperature and changes to
the recipe.
Some foods may contain micro organisms which are only destroyed by thorough cooking, therefore it is important
that the food is thoroughly cooked. If in
doubt select a longer cooking or reheating time.
Frying oil can normally be used
6-10 times. Between each use the
oil should be poured through a strainer
lined with a paper towel. Oil containing
impurities may ignite.
Turn on the Fryer only after the lid
is removed and it is filled with oil.
Do not store hot oil in plastic containers. Plastic melts!
The frying oil is no longer usable
and must be changed when it
becomes dark and thick, smells unpleasant and froths, or when it begins
to smoke at a temperature of 340° F
(170° C) or less.
Discard the used and cool oil or
grease in the trash. Do not pour it
down the sink. Oil and grease can
block the drain pipes.
Do not use a steam-cleaner to
clean the Deep Fryer.
The steam could penetrate to electrcal
components and cause a short circuit.
SAVE THESE INSTRUCTIONS AND
REVIEW THEM PERIODICALLY
Text highlighted in boxes is of particular importance and should be
read in conjunction with the Warning and Safety instructions.
Do not leave the Fryer unattended
while in use. Over-heated oil can
catch fire. Do not allow an open flame
in the vicinity of the Fryer.
7
Before using for the first time
Before using for the first time
Clean the Deep Fryer before using for
the first time.
Fill the oil reservoir with approx.
1 gallon of water and add some dishwashing liquid.
Turn the control knob clockwise to
265° F (130°C) and bring the water
to a boil. Once it has started to boil,
turn the control knob back to ”0“.
Drain the water using the drain
valve into a heat resistant container.
Remember to close the drain valve.
Rinse out the oil reservoir with hot
water.
Raise the heating element and dry
the reservoir with a clean cloth.
8
To fry, remove the lid and fill the oil
reservoir to the mark with about 3/4 gallon of clean vegetable or frying oil.
The reservoir will hold a maximum
of 1 gallon of oil.
If fat or lard is used: Cut it into small
pieces first.
When re-using solidified fat, poke a few
holes in it as far down as the element.
Melt the fat at a temperature of
212°F (100°C).
When all the fat has melted, set the
Fryer to the desired cooking temperature.
Never turn on the Fryer without oil
or fat in the reservoir, or with the lid
closed.
Frying
Frying
Turning on the Fryer
The control knob should be rotated
clockwise to turn on the Fryer, and
counter clockwise to turn it off. Do
not force the knob or it may break.
Turn the control knob to the desired
temperature.
The white indicator lamp =
illuminates to show that the Fryer is in
operation.
The yellow indicator lamp =
illuminates when the Fryer heating elements are on.
The yellow indicator lamp goes out
. . . when the selected temperature has
been reached.
When the temperature drops below that
which was selected, the elements and
indicator lamp will turn again.
This process is repeated until the Fryer
is turned off.
Check the oil level
Check the oil level before adding food.
The correct oil level is between the two
marks, located on the back of the reservoir.
Correct procedure
Before frying, wipe any moisture off
of the food.
The higher the water content of the
food, the greater the danger of the
oil foaming over.
Set the desired temperature (see
chart on page 10).
When the yellow lamp goes out,
lower the basket containing the food
into the oil.
If the the oil foams excessively, briefly
remove the food from the Fryer.
Never salt food over hot oil.
9
Frying
Frying
After frying
Draining the oil
When the food is ready:
Frying oil can normally be used 6-10
times. Between each use, the oil
should be poured through a strainer
lined with a paper towel.
Oil containing impurities may ignite.
remove the basket and shake it
lightly to remove excess oil.
In order to drain the food, the frying
basket can be suspended from the
bracket support of the heating element hinge.
Turn the control knob back to ”0“.
The indicator lamp will go out.
Replace the lid after the oil or fat
has cooled.
The frying basket has a handle which
can be folded away when not in use:
Press the sides of the handle
together and fold it into the basket.
The handle can be removed when
cleaning the frying basket.
There is a drain valve at the base of the
reservoir for draining the oil.
Before draining solid fat, turn the selector to the highest temperature to
liquify the fat. Do not allow the fat to
get too hot.
Be careful not to burn yourself with
the hot oil or fat. Let hot oil cool before draining.
Place a heat resistant container
under the drain valve.
Open the valve by turning the lever
90° to the right.
To close the valve, turn the lever as
far as possible to the left.
10
Frying
Frying
Frying chart
Food
Temperature
°C / °F
80/180
Time
in mins
6-7
Scampi (Breaded)
80/180
4
Chicken Drumsticks
75/170
16 - 18
Scotch Eggs
80/180
6-7
Stuffed Mushrooms
80/180
3
Camembert (Breaded)
75/170
5
Potato Croquettes
80/180
4
Chips
80/180
4-5
Crisps
80/180
3
Choux Pastry Puffs
90/190
4-5
Apple Fritters
90/190
6
Doughnuts
80/180
5
Fish Fillets (Battered)
Please Note: The times shown should serve as a guide - the actual cooking time
will depend on the size and quantity of food being cooked.
11
Cleaning and Care
Cleaning and Care
The lid / oil reservoir /
frying basket
These can all be cleaned using hot
water with a mild dishwashing liquid.
The lid and basket can be cleaned in a
dishwasher.
Do not use abrasive cleaning
agents, scouring powder, scrapers,
hard brushes or anything abrasive
to clean the Fryer.
See the ”Operation“ section for how
to drain the oil before cleaning the oil
reservoir.
To clean the oil reservoir, the heating
element can be swung up and suspended from the bracket on the element hinge.
To clean, use a quality stainless steel
cleaner.
Control panel / Control knobs
Do not use any scouring agents or
pads on the knobs or control panel.
Clean the control knob and the control
panel with hot water and dishwashing
liquid.
After cleaning, dry with a soft cloth.
12
After Sales Service
After Sales Service
In the event of problems you cannot
correct yourself, please contact:
Your Miele Dealer
or
The Miele Service Department
The address of the nearest Service Department is given on the back page.
When contacting the Service Department, please have the Model and Serial No. of the appliance available. Both
can be found on the data plate.
Space for supplied data plate.
13
Electrical connection
Electrical connection
Electrical connections should be
made by a qualified electrician in
accordance with all local and national ordinances.
Note to the installer:
Please leave these instructions with
the consumer.
Power supply:
Please check the dataplate for
240 VAC; 60 Hz or
208 VAC; 60 Hz
Caution:
Disconnect the appliance from the
main power supply before servicing. To reduce the risk of electric
shock, make sure that the appliance is properly grounded after
installation.
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
For CDN only
The appliances are provided with 3 terminal leads: 1 black wire, 1 red wire
and 1 green wire which have to be connected to a separate overcurrent protection device (fusebox).
All hot wires (black and red) have to be
fused individually before connecting
them to the main power supply leads.
Use 15 Amp fuses for appliances
rated 240 VAC.
Connect black terminal wire to L1
(black) and red terminal wire to L 2
(red) . The green terminal wire (ground)
has to be connected directly to the
equivalent colored power supply lead.
All connections must be done in a
proper way.
ALSO SEE THE WIRING DIAGRAM
PROVIDED WITH THE APPLIANCE.
For USA only
The appliance is provided with 3 terminal leads, 1 black wire (L 1), 1 red wire
(L 2) and 1 green wire (GND) which
must be connected to a dedicated line,
inside of an approved junction box.
Connect the black wire to L 1, the red
wire to L 2 and the green wire to GND.
ALSO SEE THE WIRING DIAGRAM
PROVIDED WITH THE APPLIANCE.
14
Electrical connection
Electrical connections
FOR CANADA ONLY
WARNING: THIS APPLIANCE MUST BE GROUNDED
Miele Fuse Box
Cap
Fuse Holder
15
Appliance dimensions
Appliance dimensions
(Large numbers denote mm)
11 3/8"
2"
20 1/16"
8 11/16"
19 5/16"
10 7/16"
16
Installation instructions
Installation instructions
This appliance is classified as ”Y“ class
for heat protection. There may be a wall
at the rear and a wall or tall cabinet at
one side. On the other side, however,
no cabinet or wall must stand higher
than the appliance.
There must be a minimum distance
of 9-7/8" (250 mm) between the appliance and adjacent cabinetry, because of the heat radiated from the
elements.
Make certain that the drain tap is accessible once the appliance is installed so that the oil can be safely
drained.
Prepare the countertop cut-out as illustrated.
Dimension ”B“ will vary depending
on how many combisets are installed. The following chart gives
Dimension ”B“ for a variety of 2 zone
(ie KM 89-2) and 4 zone (ie KM 93-2)
combinations.
Depth
in
mm
Width *
(= Dimension B)
in mm
490
490
490
490
490
265
558
851
1144
1437
490
490
490
560
1143
1728
One 2 zone
+ one 4 zone
490
851
Two 2 zone
+ one 4 zone
490
1143
Three 2 zone
+ one 4 zone
490
1437
One 2 zone
+ two 4 zone
490
1436
Two 2 zone
+ two 4 zone
490
1729
2 zone Combiset
1 Combiset
2 Combisets
3 Combisets
4 Combisets
5 Combisets
4 zone Combiset
1 Combiset
2 Combisets
3 Combisets
Combination
23/16˝
195/16˝
23/16˝
Extractor (e.g. DA 8-2)
For building in between two appliances:
- Dimension B increases by 90 mm.
For building in at the end of a combination:
- Dimension B increases by 98 mm.
* Width includes provision for V 98 spacer bar.
17
Installation instructions
Installation instructions
Depth
in
inch
Width *
(= Dimension B)
in inch
1 Combiset
2 Combisets
3 Combisets
4 Combisets
5 Combisets
19-5/16"
19-5/16"
19-5/16"
19-5/16"
19-5/16"
10-7/16"
22"
33-1/2"
45-1/32"
56-9/16"
4 zone Combiset
1 Combiset
2 Combisets
3 Combisets
19-5/16"
19-5/16"
19-5/16"
22"
45"
68"
2 zone Combiset
Combination
loosen
One 2 zone
+ one 4 zone
19-5/16"
33-1/2"
Two 2 zone
+ one 4 zone
19-5/16"
45"
Three 2 zone
+ one 4 zone
19-5/16"
56-9/16"
One 2 zone
+ two 4 zone
19-5/16"
56-1/2"
Two 2 zone
+ two 4 zone
19-5/16"
68-1/16"
Extractor (e.g. DA 8-2)
For building in between two appliances:
- Dimension B increases by 3 9/16".
For building in at the end of a combination:
- Dimension B increases by 3 7/8".
* Width includes provision for V 98 spacer bar.
Place the provided seal
edge of the Deep Fryer.
18
f under the
tighten
b Appliance
c Tensioning screw
d Clamp
e Countertop
f Seal
Turn the tensioning screws c
counter clockwise until a resistance
is felt, then turn the clamps d to the
left.
Place the appliance into position,
turn the clamps and tighten the tensioning screw until the clamps press
into the countertop e, as shown.
Connect the appliance to the electrical supply.
When installing several Combiset units,
a stainless steel spacer bar must be
placed between the units. It is supplied
with its own installation instructions.
Installation instructions
Installation instructions
To reduce the risk of fire or burns caused by reaching over heated surface units,
locating cabinet storage space above these units should be avoided.
If cabinet storage or a range hood is provided, distance A must be at least 30"
(75 cm). A range hood has to extend at least 5" (12,5 cm) beyond the front of the
cabinets.
19
Alteration rights reserved / 22/ 000
This paper consists of celluloe which has been bleached without the use of chlorine.
CDN, USA -4098