Ariens 991039 - Zoom 2452 HD Specifications

ZOOM HD
Owner/Operator Manual
Models
991039 – Zoom 2452 HD
991040 – Zoom 2660 HD
ENGLISH
03253300A 11/07
Printed in USA
TABLE OF CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Service and Adjustments . . . . . . . . . . 17
Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9
Storage . . . . . . . . . . . . . . . . . . . . . . . . . 28
Controls and Features . . . . . . . . . . . . 11
Accessories . . . . . . . . . . . . . . . . . . . . . 29
Operation . . . . . . . . . . . . . . . . . . . . . . . 12
Service Parts . . . . . . . . . . . . . . . . . . . . 29
Maintenance Schedule . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . 30
INTRODUCTION
NON-ENGLISH MANUALS
THE MANUAL
Manuals in languages other than
English may be obtained from your
Dealer. Visit your dealer or
www.ariens.com for a list of
languages available for your
equipment.
Manuals printed in languages other
than English are also available as a
free download on our website:
Before operation of unit, carefully and
completely read your manuals. The contents
will provide you with an understanding of
safety instructions and controls during normal
operation and maintenance.
All reference to left, right, front, or rear are
given from operator sitting in the operation
position and facing the direction of forward
travel.
http://www.ariens.com
SERVICE AND REPLACEMENT
PARTS
MANUALES EN IDIOMAS
DIFERENTES DEL INGLES
Puede obtener manuales en
idiomas diferentes del inglés en su
distribuidor. Visite a su distribuidor
o vaya a www.ariens.com para
obtener una lista de idiomas
disponibles para su equipo.
También puede imprimir manuales
en idiomas diferentes del inglés
descargándolos gratuitamente de
nuestra página Web:
When ordering publications, replacement
parts, or making service inquiries, know the
Model and Serial numbers of your unit and
engine.
Numbers are located on the product
registration form in the literature package.
They are printed on a serial number label,
located on the frame of your unit (Figure 1).
Serial Number Label
http://www.ariens.com
Manuels non anglais
Des manuels dans différentes
langues sont disponibles chez
votre revendeur. Rendez-vous
chez votre revendeur ou allez sur
le site www.ariens.com pour
consulter la liste des langues
disponibles pour votre équipement.
Les manuels imprimés dans des
langues différentes de l’anglais
sont également disponibles en
téléchargement gratuit sur notre
site Web :
http://www.ariens.com
GB - 2
Figure 1
OF1612
DEALER DELIVERY
• Record Unit Model and Serial numbers
here.
• Record Engine Model and Serial numbers
here.
PRODUCT REGISTRATION
The Ariens dealer must register the product
at the time of purchase. Registering the
product will help the company process
warranty claims or contact you with the latest
service information. All claims meeting
requirements during the limited warranty
period will be honored, whether or not the
product registration card is returned. Keep a
proof of purchase if you do not register your
unit.
Customer Note: If the Dealer does not
register your product, please fill out, sign and
return the product registration card to Ariens
or go to www.ariens.com on the internet.
UNAUTHORIZED REPLACEMENT
PARTS
Use only Ariens replacement parts. The
replacement of any part on this equipment
with anything other than an Ariens authorized
replacement part may adversely affect the
performance, durability, and safety of this unit
and may void the warranty. Ariens disclaims
liability for any claims or damages, whether
regarding warranty, property damage,
personal injury or death arising out of the use
of unauthorized replacement parts.
NOTE: To locate your nearest Ariens Dealer,
go to www.ariens.com.
Dealer should:
1. Test brakes after unit is assembled to be
sure adjustment has not been disturbed
in shipment (See Parking Brake
Interlock System on page 12). Wheel
brakes are properly adjusted at factory.
2. Check the safety interlock system to
make sure that it is functioning properly.
With operator on seat, unit must not start
unless steering levers are in neutral (N)
and Power Takeoff (PTO) is disengaged
(Off). Engine must stop if operator
leaves seat when steering levers are in
any drive position or PTO is engaged
(On). See Safety Interlock System on
page 12.
3. Fill out Original Purchaser Registration
Card and return the card to Ariens.
4. Explain Limited Warranty Policy.
5. Explain recommended lubrication and
maintenance. Advise customer on
adjustments. Instruct customer on
controls and operation of unit. Discuss
and emphasize the Safety Precautions.
Give customer Owner/Operator, Parts,
and Engine Manuals. Advise customer
to thoroughly read and understand them.
Customer Note: Your Dealer has been
provided complete set-up and preparation
instructions which must be completed prior to
you taking delivery of this unit. The dealer is
required to review important information in
this manual with you before or upon delivery
of the unit or attachment.
DISCLAIMER
Ariens reserves the right to discontinue,
change, and improve its products at any time
without public notice or obligation to the
purchaser. The descriptions and
specifications contained in this manual were
in effect at printing. Equipment described
within this manual may be optional. Some
illustrations may not be applicable to your
unit.
GB - 3
SAFETY
WARNING: This cutting machine
is capable of amputating hands
and feet and throwing objects.
Failure to observe the safety
instructions in the manuals and
on decals could result in serious
injury or death.
Slopes are a major factor related
to loss-of-control and tip-over
accidents. Operation on all slopes
requires extra caution.
Tragic accidents can occur if the
operator is not alert to the
presence of children. Never
assume that children will remain
where you last saw them.
Gasoline is extremely flammable
and the vapors are explosive,
handle with care.
Disengage attachment, stop unit
and engine, remove key, engage
parking brake, and allow moving
parts to stop before leaving
operator’s position.
SAFETY ALERT
SYMBOL
OL1253
These are safety alert
symbols. They mean:
•ATTENTION!
•YOUR SAFETY IS
INVOLVED!
When you see this symbol:
•BECOME ALERT!
•OBEY THE MESSAGE!
OL3900
SIGNAL WORDS
The safety alert symbols above and signal
words below are used on decals and in this
manual.
Read and understand all safety messages.
WARNING: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, COULD RESULT in
death or serious injury.
CAUTION: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, MAY RESULT in minor
or moderate injury. It may also be
used to alert against unsafe
practices.
NOTATIONS
NOTE: General reference information for
proper operation and maintenance practices.
IMPORTANT: Specific procedures or
information required to prevent damage to
unit or attachment.
PRACTICES AND LAWS
Practice usual and customary safe working
precautions, for the benefit of yourself and
others. Understand and follow all safety
messages. Be alert to unsafe conditions and
the possibility of minor, moderate, or serious
injury or death. Learn applicable rules and
laws in your area, including those that may
restrict the age of the operator.
REQUIRED OPERATOR
TRAINING
Original purchaser of this unit was instructed
by the seller on safe and proper operation. If
unit is to be used by someone other than
original purchaser (loaned, rented or sold),
ALWAYS provide this manual and any
needed safety training before operation.
SAFETY DECALS AND
LOCATIONS
ALWAYS replace missing or damaged Safety
Decals. Refer to Figure 2 for Safety Decal
locations.
DANGER: IMMINENTLY
HAZARDOUS SITUATION! If not
avoided, WILL RESULT in death
or serious injury.
GB - 4
6
2
5
4
1
3
2
OF0002
Figure 2
1. DANGER! TO AVOID SERIOUS
INJURY OR DEATH
•
•
•
Read Owner/Operator Manual.
•
OL1801
•
Keep children and others away
from unit while operating.
•
If machine stops going uphill, stop
blade and back down slowly.
Avoid sudden turns.
Keep safety devices (guards, shields,
switches, etc.) in place and working.
Check interlock system per manual
before use.
Understand location and function of all
controls.
Never allow operation by untrained
persons.
2. DANGER! ROTATING PARTS
OL4370
Never direct discharge toward
other people. Thrown objects
can cause injury. Remove
objects that could be thrown by
the blade.
OL0910
Always keep feet and hands
away from rotating parts.
OL3030
Always stand clear of discharge
area. Do not direct discharge
toward other people.
Look down and behind before
and while backing.
OL0910
Keep people away from unit
while operating.
OL4460
Keep children out of work area
and under watchful care of a
responsible adult.
OL3292
Shut off engine, remove key,
read manual before you adjust
or repair unit.
OL4470
NEVER CARRY CHILDREN.
OL4010
OL4480
Go up and down slopes, not
across.
GB - 5
NO STEP! Always keep feet
away from rotating parts.
OL4420
3. WARNING!
Do not operate mower unless guards are in
operating position or bagger is attached.
Always stand clear of discharge
area.
OL4430
Do not operate mower unless
bagger is attached or guards
are in operating position.
OL3320
4. HOT SURFACES!
DO NOT touch parts which
are hot from operation.
ALWAYS allow parts to cool.
OS0731
5. ROTATING PARTS
AVOID INJURY. Stay clear of
rotating parts.
OF3450
6. DANGER!
AVOID INJURY. Stay clear of
rotating parts.
OL4730
SAFETY RULES
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly. Failure to follow
instructions could result in personal injury
and/or damage to unit.
ALWAYS remove key and/or wire from spark
plug before assembly. Unintentional engine
start up can cause death or serious injury.
Complete a walk around inspection of unit
and work area to understand:
• Work area • Your unit • All safety decals
Determine which attachments are needed
and can be used safely.
Inspect unit before each use for: missing or
damaged decals and shields, correctly
operating safety interlock system, and
deterioration of grass catchers. Replace or
repair as needed.
ALWAYS check overhead and side
clearances carefully before operation.
ALWAYS be aware of traffic when operating
along streets or curbs.
Keep children and people away.
Keep children out of work area and under
watchful care of a responsible adult.
Keep area of operation clear of all toys, pets,
and debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or
floors. Avoid uneven work areas and rough
terrain. Stay alert for hidden hazards or traffic.
DO NOT operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Data indicates that operators, age 60 and
above, are involved in a larger percentage of
riding mower related injuries. These
operators should evaluate their ability to
operate the riding mower safely enough to
protect themselves and others from serious
injury.
Read the entire Owner/Operator manual and
other training material. If the operator or the
mechanic cannot read the manual, it is the
owner’s responsibility to explain it to them.
Only the user can prevent and is responsible
for accidents or injuries occurring to
themselves, other people or property.
Only trained adults may operate or service
unit. Training includes actual operation.
Local regulations may restrict the age of the
operator.
NEVER allow children to operate or play on
or near unit. Be alert and shut off unit if
children enter area.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation
requires your complete and unimpaired
attention at all times.
DO NOT wear loose clothing or jewelry and
tie back hair that may get caught in rotating
parts.
Wear adequate outer garments.
NEVER wear open sandals or canvas shoes
during operation. Wear adequate safety gear,
protective gloves and footwear.
Wear proper footwear to improve footing on
slippery surfaces.
GB - 6
Always wear safety goggles or safety glasses
with side shields when operating mower.
Moving parts can cut or amputate fingers or a
hand. Wrap blade(s) or wear gloves to
service. On multiblade mowers, rotation of
one blade will cause all blades to rotate.
NEVER place your hands or any part of your
body or clothing inside or near any moving
part while unit is running.
ALWAYS keep hands and feet away from all
rotating parts during operation. Rotating parts
can cut off body parts.
ALWAYS keep body and hands away from
pin holes or nozzles which eject hydraulic
fluid under pressure.
DO NOT touch parts which are hot. Allow
parts to cool.
ALWAYS keep hands and feet away from all
pinch points.
Fumes from the engine exhaust can cause
death or serious injury. DO NOT run engine in
an enclosed area. Always provide good
ventilation.
Read, understand, and follow all instructions
in the manual and on the machine before
starting. Understand:
• How to operate all controls
• The functions of all controls
• How to STOP in an Emergency
• Braking and steering characteristics
• Turning radius and clearances
Keep safety devices or guards in place and
functioning properly. NEVER modify or
remove safety devices.
Do not operate without either entire grass
catcher or the discharge guard in place.
Stop engine before removing grass catcher or
unclogging chute.
Ensure Safety Interlock System is functioning
properly. DO NOT operate unit if safety
interlock is damaged or disabled.
Start and operate unit only when seated in
operator’s position. Steering control levers
must be in neutral, PTO disengaged and
parking brake set when starting engine.
Use care when approaching blind corners,
shrubs, trees or other objects that may
obscure vision.
Dust, smoke, fog, etc. can reduce vision and
cause an accident. Mow only in daylight or
good artificial light.
Avoid slippery surfaces. Always be sure of
your footing.
DO NOT mow on wet grass. Reduced
traction could cause sliding and effect the
machine’s stability.
Watch for traffic when operating near or
crossing roadways.
Never carry passengers.
DO NOT try to stabilize the machine by
putting your foot on the ground.
Never direct discharge towards persons or
property that may be injured or damaged by
thrown objects. Use extreme caution on
gravel surfaces.
Always stand clear of the discharge area.
ALWAYS disengage PTO, stop unit and
engine, remove key, engage parking brake
and allow moving parts to stop before leaving
operator’s position.
Never engage PTO while raising attachment
or when attachment is in raised position.
DO NOT operate at too fast a rate. DO NOT
change engine governor settings or overspeed engine. Slow down before turning.
DO NOT operate in reverse unless absolutely
necessary. ALWAYS look down and behind
before and while backing.
Stop and inspect equipment if you strike an
object or if there is an unusual vibration.
Repair, if necessary, before restarting. Never
make adjustments or repairs with the engine
running.
Mower blades are sharp and can cut you.
Wrap the blade(s) or wear gloves, and use
extra caution when servicing them. NEVER
weld or straighten mower blades.
Rotation of one blade may cause rotation of
the other blades.
Take all possible precautions when leaving
unit unattended. Shut off engine. Remove
wire from spark plug and secure it away from
spark plug.
ALWAYS remove key to prevent unauthorized
use.
Know the weight of loads. Limit loads to those
you can safely control and the unit can safely
handle.
Disengage PTO when attachment is not in
use. ALWAYS turn off power to attachment
when travelling, crossing driveways, etc.
Mow up and down slopes, not across them.
Use of a Rollover Protection System (ROPS)
is recommended for slope operation. See
Attachments and Accessories.
GB - 7
Always wear a seat belt when operating unit
using a Rollover Protection System (ROPS).
Keep all movements on the slope slow and
gradual. Do not make sudden changes in
speed or direction.
Avoid starting or stopping on the slope. If tires
lose traction, disengage the blades and
proceed slowly straight down the slope.
If you cannot back up a slope or you feel
uneasy on it, do not mow it.
DO NOT park on slopes unless necessary.
When parking on slope always chock or block
wheels. Always set parking brake.
Use a slow speed. Tires may lose traction on
slopes even though the brakes are
functioning properly.
Do not bypass transmission when on a slope.
Tow only with a machine that has a hitch
designed for towing. Do not attach towed
equipment except at the hitch point.
Follow the manufacturer’s recommendations
for weight limits for towed equipment and
towing on slopes.
NEVER allow children or others in or on
towed equipment.
On slopes, the weight of the towed equipment
may cause loss of control.
Travel slowly and allow extra distance to stop.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
ALWAYS turn off power to attachment and
shut off fuel when transporting unit.
Keep unit free of debris. Clean up oil or fuel
spills.
This product is equipped with an internal
combustion type engine. DO NOT use unit on
or near any unimproved, forest-covered or
brush covered land unless exhaust system is
equipped with a spark arrester meeting
applicable local, state or federal laws. A spark
arrester, if it is used, must be maintained in
effective working order by operator.
Fuel is highly flammable and its vapors are
explosive. Handle with care. Use an
approved fuel container.
NO smoking, NO sparks, NO flames.
ALWAYS allow engine to cool before
servicing.
NEVER fill fuel tank when engine is running
or hot from operation.
NEVER fill or drain fuel tank indoors.
Replace fuel cap securely and clean up
spilled fuel.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lockopen device.
If fuel is spilled on clothing, change clothing
immediately.
Avoid Electric Shock. Objects contacting both
battery terminals at the same time may result
in injury and unit damage. DO NOT reverse
battery connections.
Reverse connections may result in sparks
which can cause serious injury. Always
connect positive (+) lead of charger to
positive (+) terminal, and negative (-) lead to
negative (-) terminal.
ALWAYS disconnect negative (-) cable FIRST
and positive (+) cable SECOND. ALWAYS
connect positive (+) cable FIRST, and
negative (-) cable SECOND.
Explosive Gases from battery can cause
death or serious injury. Poisonous battery
fluid contains sulfuric acid and its contact with
skin, eyes or clothing can cause severe
chemical burns.
No flames, No sparks, No smoking near
battery.
ALWAYS wear safety glasses and protective
gear near battery. Use insulated tools.
DO NOT TIP battery beyond a 45° angle in
any direction.
ALWAYS keep batteries out of reach of
children.
Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer and reproductive
harm. Wash hands after handling.
ALWAYS block wheels and know all jack
stands are strong and secure and will hold
weight of unit during maintenance.
Release pressure slowly from components
with stored energy.
GB - 8
NEVER attempt to make any adjustments to
unit while engine is running (except where
specifically recommended). Stop engine,
remove key or spark plug wire and wait for all
moving parts to stop before servicing or
cleaning.
Check parking brake operation frequently.
Adjust and service as required.
ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler can
cause fire or explosion.
Maintain or replace safety and instruction
labels, as necessary.
NEVER store unit with fuel in fuel tank, inside
a building where any ignition sources are
present.
Shut off fuel and allow engine to cool
completely before storing in closed area or
covering unit.
Clean grass and debris from unit, especially
from around muffler and engine, to help
prevent fires.
For extended storage, shut off fuel and clean
unit thoroughly. See engine manual for proper
storage.
Lower cutting deck unless a positive
mechanical lock is used.
Use only attachments or accessories
designed for your unit.
Check all hardware at regular intervals,
especially blade attachment bolts. Keep all
hardware properly tightened.
Check attachment components frequently. If
worn or damaged, replace with
manufacturer’s recommended parts.
ASSEMBLY
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
UNIT ASSEMBLY
Package Contents:
Unit, Mower Deck and Literature Pack
Preparation Checklist
Refer to the Owner/Operator manual as
required.
1. Unpack Unit - Remove shrink wrap and
packaging materials.
2. Remove Unit From Container - Open
Bypass Valves (dump valves) (See
Moving the Unit with the Engine Off on
page 15).
Push unit from container onto a level
surface. Close the bypass valves.
3. Tires - See Specifications on page 30.
CAUTION: Avoid injury! Explosive
separation of tire and rim parts is
possible when they are serviced
incorrectly:
• Do not attempt to mount a
tire without the proper
equipment and experience
to perform the job.
• Do not inflate the tires
above the recommended
pressure.
• Do not weld or heat a wheel
and tire assembly. Heat can
cause an increase in air
pressure resulting in an
explosion. Welding can
structurally weaken or
deform the wheel.
• Do not stand in front or over
the tire assembly when
inflating. Use a clip-on
chuck and extension hose
long enough to allow you to
stand to one side.
4. Seat - See Seat Adjustments on
page 13 and Service Position on
page 17.
5. Position Steering Levers - Rotate
eccentric spacers to align handlebars.
Tighten hardware securely. See Aligning
the Steering Levers (Figure 14) on
page 23.
6. Battery - Remove battery from unit and
charge (See Battery on page 21).
GB - 9
7. Check Engine Crankcase - Check and
add oil if needed. See Engine Manual for
specifications.
8. Fill Engine Fuel Tank - Add clean fuel to
the fuel tank.
IMPORTANT: Refer to Engine Manual for fuel
type.
9. Hardware - Check for loose hardware.
10. Check Safety Interlock System - Check
to see that the interlock system operates
correctly (See Safety Interlock System
on page 12).
1
2
1
3
WARNING: FAILURE OF
INTERLOCK together with
improper operation can result in
severe personal injury.
11. Lubrication - Lubricate all fittings per
maintenance label under seat and check
hydrostat oil level (See Lubricate Unit on
page 22).
12. Level Deck - Check unit to ensure deck
level set at factory has been maintained
(See Leveling the Mower Deck on
page 27).
13. Check Function of all Controls - Ensure
unit runs and performs properly.
WARNING: FAILURE OF
CONTROLS could result in death
or serious injury.
GB - 10
1. Steering
Levers
2. Seat
3. Mounting
Hardware
Figure 3
OF3141
CONTROLS AND FEATURES
10
16
15
2
3
1
9
4
11
7
14
6
8
12
OF4035
OF4095
OM4090
OM4085
5
Figure 4
1. Fuel Tanks and Caps
2. Steering Levers
3. Hydraulic Oil Reservoir
4. Ignition Switch
5. Hour Meter
6. Throttle Lever
7. Choke Control
8. Power Take Off (PTO) Switch
13
9. Battery
10. Fuel Shut Off Valve
11. Mower Lift Pedal
12. Mower Deck
13. Mower Lift Lock
14. Seat Adjustment Lever
15. Parking Brake
16. Bypass Valve Lever
GB - 11
OPERATION
Steering Levers
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
A
B
C
D
CONTROLS AND FEATURES
See Figure 4 for Controls and Features
locations.
07757600B
Safety Interlock System
WARNING: Safety interlock
system failure and improper
operation of unit can result in
death or serious injury. Test this
system each time the unit is
operated. If this system does not
function as described, do not
operate until repairs are made.
Perform the following tests to ensure the
safety interlock system is working properly. If
the unit does not perform as stated, contact
your Ariens dealer for repairs.
NOTE: When the parking brake is engaged,
the steering levers are locked in neutral.
Test Steering PTO
Levers
Parking
Brake
Engine
STARTING INTERLOCK
1
Neutral Off
Engaged Starts
2
Neutral On
Engaged Doesn’t
Start
3
Neutral Off
Disengaged
Doesn’t
Start
The steering levers control speed and
direction. In addition, they will stop the unit.
A. For reverse travel, pull both steering
control levers backward.
B. For straight forward travel, push both
steering control levers forward.
C. To turn left, pull the left back or push
the right steering control lever forward
or a combination of both.
D. To turn right, pull the right back or
push the left steering control lever
forward or a combination of both.
To stop, return both steering levers to neutral.
NOTE: The steering controls are
mechanically locked in neutral whenever the
parking brake is engaged.
NOTE: Aggressive turning can scuff or
damage lawns. ALWAYS keep both wheels
rotating when making sharp turns. DO NOT
make turns with inside wheel completely
stopped. To obtain minimum turning radius,
slowly reverse inside wheel while moving
outside wheel slowly forward.
OPERATING INTERLOCK (ENGINE ON)
Ignition Switch
4*
Neutral On
Engaged Shuts Off
5*
Neutral Off
Disengaged
Operate the ignition switch
with the removable key.
The switch has three
positions: Off (1), On (2)
and Start (3). To start the
engine, turn the key to
Start, then release to On.
To stop the engine, turn
the key to Off.
Shuts Off
* Operator lifts off seat.
OF1750
Parking Brake Interlock System
With the parking brake engaged, the steering
levers must be locked in neutral.
With the parking brake disengaged, the
engine must not start and the engine must
shut off if the operator leaves the seat.
GB - 12
Choke Control
OF1680
Mower Lift Pedal
Push the choke lever
forward to start a cold
engine. Pull the choke
lever to the rear when the
engine gets warm.
Throttle Lever
The throttle lever changes
the engine speed. Move
the throttle lever to Fast (1)
to increase engine speed.
Move the lever to Slow (2)
to decrease engine speed.
1
OF1700
Mower lift pedal raises and lowers mower
deck for mowing or transport.
Transport:
Push mower lift pedal all the way forward until
lift lock engages.
Cutting Height:
Put cutting height adjustment pin in desired
hole. Push mower lift pedal forward and hold
it while pushing down on the lift lock. Slowly
lower mower lift pedal until deck lift contacts
cutting height adjustment pin.
Fuel Shut-Off Valve
2
OFF
LEFT
TANK
OF1700
Drive
Bypass Valve Lever
RIGHT
TANK
Pull the lever back to set
the pump in neutral and
move the unit with the
engine off.
Push the lever in to set the
pump in the drive position
and operate the unit.
OF1881
Use this valve to control
fuel flow from left or right
fuel tank.
Open the valve to
operate the engine. Turn
the valve to "Off" when
storing or transporting
the unit.
Parking Brake Lever
1. Pull lever up to engage
parking brake.
2. Push lever down to
disengage parking brake.
Neutral
OF1740
Seat Adjustments
ON
Power Take Off (PTO)
Switch
Power take off (PTO)
switch engages and
disengages the mower
blades.
Pull the power take off
(PTO) switch to "On"
OE0261
position to engage mower
OFF
blades.
Push the power take off
(PTO) switch to "Off" position to disengage
mower blades.
NOTE: The engine will not start unless the
steering control levers are in the neutral
position, the PTO switch is in the “Off”
position and parking brake is set.
WARNING: Make all seat
adjustments with unit stationary,
parking brake on and engine shut
off.
To adjust seat forward or backward:
1. While seated, pull seat adjustment lever
outward and slide seat into desired
position.
2. Release lever and slide seat forward or
back to lock seat into position.
GB - 13
Hour Meter
4. Check Tire Pressure
Records total number of
hours the engine has
been run.
5. Check Hydraulic Fluid Level
IMPORTANT: Keep a
record of Hour Meter
readings for
recommended Lubrication
and Maintenance
Be sure all controls can be reached safely
from operator’s position.
6. Adjust Seat
intervals.
NOTE: For accurate readings be sure Ignition
Switch is OFF when unit is not in operation.
7. Set Cutting Height
Make sure the deck is set to the correct
cutting height.
STOPPING IN AN EMERGENCY
The unit can be stopped immediately at any
time by turning the ignition key to the "Off"
position.
FILLING FUEL TANK
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
STARTING AND SHUT OFF
CAUTION: Read entire
Owner/Operator Manual, Clutch
Manual, and Engine Manual first.
DO NOT attempt to start engine
at this time.
Add fuel to Fuel Tank as needed. See your
Engine Manual for correct type and grade of
fuel.
To add fuel to the fuel tank:
1. Place unit in an open or well-ventilated
open area.
2. Stop the engine and allow it to cool.
3. Clean the fuel cap and the area around
the fuel cap to prevent dirt from entering
the fuel tank. Remove the cap from the
fuel tank.
4. Fill the fuel tank to within 1 in. (25 mm)
below bottom of filler neck.
5. Replace fuel cap and tighten.
6. Clean up any spilled fuel.
PRE-START
CAUTION: Make sure all
hardware is tight, all safety
devices are in place and all
adjustments are made correctly.
1. Check Safety Interlock System
If this system does not function as described
do not operate until repairs are made.
2. Check Air Cleaner
Check air filter for dirt. Clean as required.
Follow Engine Manual Maintenance
Schedule.
TO MOW WITH UNIT
3. Check Engine Fuel and Crankcase
Oil
Check and add fuel if required. Check that
engine crankcase oil is full. Follow Engine
Manual Maintenance Schedule.
To start the engine:
1. Make sure the steering levers are in
neutral.
2. Put the PTO switch in the “Off” position.
3. Engage parking brake.
4. If the engine is cold, move the choke
control to the “On” position. If the engine
is warm or hot, do not use choke.
5. Move the throttle to 3/4 “Fast” position.
See Engine Manual for detailed
instructions.
6. Put the ignition key in the switch and
turn it to the “Start” position.
7. As soon as the engine starts, release the
key.
8. Move the choke control to the “Off”
position from the “Choke” position. Wait
until the engine is running smoothly
before operation.
To stop the engine:
1. Bring the steering levers to neutral.
Disengage the PTO and engage the
parking brake.
2. Move the throttle lever to the “Slow”
position.
3. Turn the ignition key to the “Off” position.
Operate the unit only when seated in the
operator’s position.
1. Start the engine. Let the engine warm
until it is running smoothly.
2. Release parking brake.
GB - 14
WARNING: Move the steering
control levers slowly and keep the
throttle control lever at slow
speed until you learn how to
operate the unit.
3. Bring the steering levers to neutral.
4. Slow the engine down to about 3/4
speed.
5. Turn ON the PTO switch to engage the
mower.
IMPORTANT: Never engage the PTO if the
mower is plugged with grass or other
material. This may cause damage to the
electric clutch.
6. Move throttle control to fast.
7. Move the steering levers forward to
obtain a slow ground speed.
8. To disengage the mower, move the PTO
switch to the “Off” position.
9. When you know how to operate the unit,
select a speed appropriate to your
mowing conditions.
Push Lever In to Drive Position
PARKING
To park the unit:
1. Bring the steering levers to neutral. Turn
off PTO.
2. Move the throttle lever to the “Slow”
position.
3. Engage the parking brake.
4. Lower the attachment.
5. Turn the ignition key to the “Off” position
and remove the key.
Pull Lever Out to the Neutral Position
MOVING THE UNIT WITH THE
ENGINE OFF
IMPORTANT: Never tow unit.
1. Shut OFF engine.
2. Place seat in the service position (See
Service Position on page 17).
3. Pull the right and left bypass levers to
the neutral position.
OF4105
OF4110
Figure 5
WARNING: Do not bypass
transmission when on a slope.
4. Disengage parking brake.
5. Push unit to desired location.
6. Engage parking brake.
7. Push the right and left bypass levers to
the drive position.
GB - 15
FOR BEST PERFORMANCE
Mow with the engine set at full throttle.
When mulching, only remove 1/3 of grass
length per cutting. Do not cut more than 1
inch (2.54 cm) at any one time.
Discharge clippings into areas already cut.
Vary cutting pattern with each mowing.
Do not allow grass or debris to collect inside
of mower deck. Clean after each use.
Cut grass when it is dry.
Keep mower blades sharp.
Keep mower deck properly levelled.
Adjust anti-scalp rollers to prevent scalping.
Do not set height of cut too low. For very tall
grass, mow twice.
Do not travel too fast.
MAINTENANCE SCHEDULE
Proper maintenance can prolong the life of
unit. The following charts show the
recommended service schedule. More
frequent service may be required due to
working conditions (heavy loads, high
ambient temperatures, dusty conditions, or
airborne debris).
See the maintenance instructions in the
Engine Manual for additional information.
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
Period
Service
Task
Check Safety Interlock
Each
Use
WARNING: Safety interlock system
failure and improper operation of unit can
result in death or serious injury. Test this
system each time the unit is operated. If
this system does not function as
described, do not operate until repairs are
made. See Safety Interlock System on
page 12.
Check Parking Brake
Interlock System
See Parking Brake Interlock System on page 12.
Check Hydraulic Fluid
Check hydraulic oil level mark on cap/dipstick. Add
15W50 synthetic oil as needed. Do not overfill. See
Check Hydraulic Fluid Level on page 18.
Check Tires
See Specifications on page 30 for correct tire
pressure.
•
•
CAUTION: Avoid injury! Explosive
separation of tire and rim parts is possible
when they are serviced incorrectly:
•Do not attempt to mount a tire without the
proper equipment and experience to
perform the job.
•Do not inflate the tires above the
recommended pressure.
Do not weld or heat a wheel and tire
assembly. Heat can cause an increase in air
pressure resulting in an explosion. Welding
can structurally weaken or deform the
wheel.
Do not stand in front or over the tire
assembly when inflating. Use a clip-on
chuck and extension hose long enough to
allow you to stand to one side.
GB - 16
Period
Service
Task
Each
Use
Follow Engine Manual
Maintenance Schedule
Perform scheduled engine maintenance. Refer to
engine manual for detailed instructions.
Every
25
Hours
Check Mower Blades
Check mower blades for wear. Sharpen or replace
as needed. See Mower Blades on page 19.
Every
50
Hours
Lubricate Unit
Oil all pivot points and pin connections. Grease
lube fittings. See Lubricate Unit on page 22.
Check Brake Gap
Adjust gap if nessessary. See Adjusting the
Parking Brake on page 24.
Clean Battery
Keep battery and its terminals clean. See Clean
Battery on page 21.
Check Fasteners
Check mower blade mounting hardware and all
other fasteners. Replace missing or damaged
fasteners. Tighten all nuts and bolts to their correct
torque value.
Check Belts
Replace worn or deteriorated belts. See Replacing
Mower Belts on page 25 and Replacing the Hydro
Pump Belt on page 25.
Change Hydraulic Fluid
and Filter*
Drain hydraulic fluid tank, replace hydraulic oil filter,
refill system. See Hydraulic Fluid on page 18.
Every
100
Hours
Every
400
Hours
*Change hydraulic fluid and filter after first 75 hours of operation.
SERVICE AND ADJUSTMENTS
Ariens Dealers will provide any service which
may be required to keep your unit operating at
peak efficiency. Should engine service be
required, it can be obtained from a Ariens
Dealer or the engine manufacturer’s
authorized service center.
SERVICE POSITION
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
1. Place unit on a flat level surface.
ALWAYS stop engine. Ensure unit is
secure and will not tip over. Strap and
clamp onto lift if used.
2. Place steering levers in neutral and
engage parking brake.
3. Remove hex nut.
4. Tip seat forward (Figure 6).
CAUTION: Be sure footing is
secure to accomodate weight
shift of seat when rotating it into
service position.
CAUTION: HOT SURFACES
may result in injury. DO NOT
touch engine or drive parts which
are hot from operation. Allow
parts to cool before servicing.
5. When service is complete, lower seat
and secure with hex nut.
GB - 17
Check Hydraulic Fluid Level
2
1
Check the system with the unit cold and
parked on a flat, level surface.
Then run the unit for about one minute and
recheck the levels.
2
To Add Hydraulic Fluid:
1. Remove the cap from the expansion
tank.
2. Fill the expansion tank with Mobil 1
Extended Performance 15W50 or
equivalent (Ariens p/n 00057100) until
oil level reaches the cold fill line on the
tank.
3. Install the expansion tank cap and then
purge the system. See Purging the
Hydraulic System on page 19.
3
OM4110
The hydraulic fluid should be at the cold
fill line of the expansion tank.
4
1. Service
Position
2. Steering
Levers
3. Parking Brake
4. Battery
Figure 6
HYDRAULIC FLUID
WARNING: HYDRAULIC FLUID
can result in severe burns. Fluid
in hydraulic system can penetrate
skin and result in serious injury or
death.
Be sure to stop the engine before
doing any work on hydraulic
parts.
Keep body and hands away from
pin holes or nozzles which expel
hydraulic fluid when under
pressure. Use paper or
cardboard, not hands, to search
for leaks.
Ensure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to system.
FOREIGN FLUID INJECTED
INTO BODY can result in
gangrene. Fluid must be
surgically removed within a few
hours by a doctor familiar with
this form of injury.
Figure 7
Change Hydraulic Fluid and Filter
NOTE: Change hydraulic fluid and filter after
first 75 hours of operation. Change the
hydraulic oil filter and hydraulic oil every 400
hours. Use Mobil 1 Extended Performance
15W50 Synthetic Oil or equivalent for best
component life (Ariens p/n 00057100).
1. Place container under oil filter to catch
oil.
2. Remove the filter guard and oil filter from
the transaxle.
3. Remove the oil drain plug or fitting from
the inlet port and allow the transaxle to
drain completely.
4. Clean the filter mounting surface and
then lubricate rubber gasket on new oil
filter with clean hydraulic oil.
GB - 18
5. Spin new oil filter onto filter housing until
it makes contact. Tighten oil filter
another 3/4 turn.
6. Install the filter guards removed in
step 2. Tighten the mounting screws to
65 lbf-in (7.3 N•m).
7. Repeat steps 1–6 for the other
transaxle.
8. Follow the instructions in To Add
Hydraulic Fluid: on page 18.
4. Stop the engine and put the transaxle
bypass levers in the drive position. See
Moving the Unit with the Engine Off on
page 15.
5. Start the engine and slowly move the
steering levers in forward and reverse
five or six times.
6. Stop the engine, check the oil level and
add oil as needed.
7. Repeat steps 2–6 until the transaxles
operate smoothly in forward and reverse
at normal speeds without excessive
noise.
2
1
MOWER BLADES
Remove
CAUTION: Use sturdy gloves or
padding to protect hands when
working with mower blades.
3
1. Turn the engine off. Remove the ignition
key. Remove the ignition wire from the
spark plugs.
2. Remove the bolts, cup washer, and
blades from the spindle shafts.
4
1.
2.
3.
4.
Replace
Drain Plug
Oil Filter
Filter Guard
Mounting Hardware
1. Put the blades, cup washers, and the
bolts back on the spindle shafts.
2. Tighten the bolts to a torque of 115125 lbf-ft (156-169.5 N•m).
3. Replace the ignition wire on the spark
plugs.
Figure 8
Purging the Hydraulic System
WARNING: This adjustment
requires operating the engine.
Use extreme care to avoid
contact with moving parts and hot
surfaces. Be sure rear of unit is
well supported and secure before
starting engine.
1. With the unit up to and facing a wall, jack
up the unit so that both drive wheels are
off the ground.
2. Disengage the parking brake and put the
transaxle bypass levers in the neutral
position. See Moving the Unit with the
Engine Off on page 15.
3. Start the engine and slowly move the
steering levers in forward and reverse
five or six times.
GB - 19
3. Check mower blade balance.
Slide mower blade on an unthreaded
bolt. A balanced blade should remain in
a horizontal position. If either end of
mower blade moves downward, sharpen
the heavy end until blade is balanced.
4. Install mower blade(s) on unit.
5. Tighten the bolts to a torque of 115-125
lbf-ft (156-169.5 N•m).
1
DO NOT Sharpen to This Pattern
2
2
1
3
1. Blade
2. Cup Washer
3. Bolt
DISCARD if More Than
1/2 in. (1.27 cm)
4
1
Figure 9
Sharpen the Mower Blades
CAUTION: DO NOT sharpen
mower blades while on unit. An
unbalanced mower blade will
cause excessive vibration and
eventual damage to unit. Check
mower blade balance before
reinstalling blades.
NEVER weld or straighten bent
blades.
3
OT0792
4
Sharpen to This Pattern
1. Cutting Edge
2. Square
Corner
1. Remove mower blade from unit.
Discard mower blade if:
• More than 1/2 in. (1.27 cm) of metal is
removed.
• Air lifts become eroded.
• Blade is bent or broken.
2. Sharpen mower blade by removing an
equal amount of material from each end
of mower blade. DO NOT change angle
of cutting edge or round the corner of the
mower blade.
GB - 20
Figure 10
3. Air Lift
Erosion
4. Air Lift
BATTERY
2
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
1
WARNING: Battery posts,
terminals and related accessories
contain lead and lead
compounds, chemicals known to
the State of California to cause
cancer and reproductive harm.
Wash hands after handling.
3
OF1671
Unit comes equipped with a maintenancefree battery that requires no regular
maintenance except cleaning the terminals.
1. Negative
terminal
2. Positive
terminal
Remove Battery
1. Shut OFF engine. Engage parking
brake. Remove the ignition key.
2. Place seat in the service position (See
Maintenance Schedule on page 16).
3. Disconnect cables from battery
(negative, then positive) (Figure 11).
4. Remove hold down and remove battery.
Figure 11
1. Remove battery from unit. See Remove
Battery on page 21.
2. Clean terminals and battery cable ends
with wire brush.
3. Coat terminals with dielectric grease or
petroleum jelly.
4. Replace battery. See Replace Battery on
page 21.
Replace Battery
1. Replace battery and secure with battery
hold down.
2. Reconnect cables to battery (positive,
then negative). Position boot over
positive terminal.
3. Return seat to operating position.
Clean Battery
Keep battery and its terminals clean. Inspect
every 100 operating hours or monthly for best
performance.
3. Battery
Charging the Battery
Battery Electrolyte First Aid
Follow First Aid directions for contact with
battery fluid.
• External Contact: Flush with water.
• Eyes: Flush with water for at least 15
minutes and get medical attention
immediately!
• Internal Contact: Drink large quantities
of water. Follow with Milk of Magnesia,
beaten egg or vegetable oil. Get
medical attention immediately!
In case of internal contact, DO NOT induce
vomiting!
IMPORTANT: DO NOT fast charge. Charging
at a higher rate will damage or destroy
battery. ONLY use an automatic charger
designed for use with your battery.
ALWAYS follow information provided on
battery by battery manufacturer. Contact
battery manufacturer for extensive
instructions to charge battery.
1. Remove battery from unit. See Remove
Battery on page 21.
GB - 21
2. Place battery on bench or other wellventilated place.
3. Connect positive (+) lead of charger to
positive (+) terminal, and negative (–)
lead to negative (–) terminal.
4. Charge battery according to charger and
battery manufacturers’ instructions.
5. Replace battery. See Replace Battery on
page 21.
Jump-Starting
Ariens does not recommend jump-starting
your unit. Jump-starting can damage engine
and electrical system components. See your
engine manual for more detailed information.
LUBRICATE UNIT
Apply oil at all pivot points and pin
connections.
1
OF1794
R LUBRICA- QTY
E
TION
F
1 REPACK
2
OIL
LOCATION
INTERVAL
CASTER
400 Hrs
PIVOT
ALL PIVOT 50 Hrs
POINTS, PIN
CONNECTIONS
2. With the unit up to and facing a wall, jack
up the unit so that both drive wheels are
off the ground.
3. Remove the drive wheels from the unit.
4. Start the engine, run engine at full
throttle, and release the parking brake.
5. Move the steering levers from Forward
to Reverse several times to make sure
controls are free. Then return steering
levers to neutral position.
6. Check wheel(s) for movement.
NOTE: The right and left hydraulic pumps are
adjusted the same way.
7. If a wheel moves, adjust the return to
neutral mechanism on the hydraulic
pump:
a. Loosen the return to neutral screw
on the pump.
b. Slowly move the speed and
direction control bracket clockwise
or counterclockwise until the
wheel stops moving.
c. Hold the stop bracket in position
and tighten the return to neutral
screw on the pump.
8. Move steering levers from Forward to
Reverse several times and return
steering levers to neutral position.
Check wheel(s) for movement.
9. If wheel is still moving, repeat steps 7
and 8.
10. Shut OFF engine.
11. Replace drive wheels.
Axle Direction
Return to Neutral
Adjusting Screw
Figure 12
STEERING CONTROL NEUTRAL
ADJUSTMENT
Eliminating Excessive Creeping of
the Unit (Figure 13)
Speed and
Direction
Control Arm
WARNING: This adjustment
requires operating the engine.
Use extreme care to avoid
contact with moving parts and hot
surfaces. Be sure rear of unit is
well supported and secure before
starting engine.
Figure 13
1. If hydraulic system is cold, run unit for a
minimum of five minutes, then shut OFF
engine.
GB - 22
ADJUSTING THE UNIT TO TRACK
STRAIGHT
Aligning the Steering Levers
(Figure 14)
1. Shut OFF engine. Engage parking
brake. Remove the ignition key.
2. Place seat in the service position (See
Service Position on page 17).
3. Loosen brake interlock on the same side
as steering lever to be adjusted.
4. Loosen tie rod jam nuts and turn tie rod
until steering levers are aligned.
5. Tighten jam nut on tie rod, tighten brake
interlock.
3
1
WARNING: Prior to adjusting the
tracking of the unit, shut OFF
engine, engage parking brake,
and remove the ignition key.
Check and adjust tire pressure. Increase
pressure on side unit tracks to. DO NOT
exceed maximum recommended tire
pressure (See Specifications on page 30).
If tire pressure adjustment does not solve
tracking problem, adjust the limiter bolts on
the stop bracket (Figure 15). Front bolts
adjust forward and rear bolts adjust reverse.
Lengthen the limiter bolt (move closer to
lever) on side which is too fast.
2
2
3
2
1
1
4
4
1. Limiter Bolt
2. Jam Nut
3. Steering
Lever
5
1
1. Tie-Rod Jam
Nut
2. Tie-Rod
3. Steering
Lever
Figure 14
4. Brake
Interlock
5. Hydrostatic
Transmission
Figure 15
OF3381
GB - 23
4. Stop
Bracket
ADJUSTING THE HEIGHT OF THE
STEERING LEVER HANDLES
1. Engage parking brake and set both
transmission bypass valves to the
neutral position. See Moving the Unit
with the Engine Off on page 15.
2. Push the unit forward.
If the unit easily rolls forward the
transmission brakes are not fully
engaging. Tighten the brake cable to
fully engage the brake lever on the
transmission.
The handles have three height positions
(Figure 16).
2
Adjust the Parking Brake
1
Position # 1
Position # 2
Position # 3
1. Disengage the parking brake.
2. Loosen the nuts on the parking brake
cable adjuster and then turn the adjuster
until the cable is taut, not tight.
3. Engage the parking brake and check the
adjustment. Repeat as needed.
4. Tighten the nuts.
NOTE: Set both bypass valves to the drive
position when finished adjusting the brake.
3
1
4
1. Spacer
2. Handle
3. Eccentric
Spacer
2
4. Steering
Lever
Figure 16
OF3745
1. Shut OFF engine. Engage parking
brake. Remove the ignition key.
2. Remove the spacer, handle, and
eccentric spacer from the steering lever.
NOTE: Position the right and left handles at
the same height position.
3. Install the spacer, handle, and eccentric
spacer in the appropriate height position.
Do not tighten the nut holding the
eccentric spacer.
4. Turn the eccentric spacer until the right
and left handles are the same height.
Tighten nut.
3
1. Parking Brake Cable
2. Adjuster
3. Nuts
Figure 17
PTO BELT
ADJUSTING THE PARKING
BRAKE
The parking brake should not need
adjustment, however if the parking brake
does not hold the unit properly, the brake may
need adjustment.
Check Adjustment
NOTE: Be sure to check the parking brake on
both sides of the unit (Figure 17).
GB - 24
WARNING: MOVING PARTS can
cut or amputate body parts.
ALWAYS wait for moving parts to
stop before performing
maintenance or service.
CAUTION: DAMAGED OR
WORN BELTS may result in
injury and/or damage to unit.
Check belts for excessive wear or
cracks often.
PTO Belt Access
4. Remove short mower belt from right
blade spindle and from deck. Idler pivot
bolt must be loosened slightly to gain
clearance to remove belt from under
idler pulley (Figure 19).
5. Arrange new mower belt(s) on deck
(short belt first). Retighten short mower
belt idler pivot bolt. Install belts on
sheaves. Put belts onto center sheave
last.
6. Replace belt covers and return foot
board to closed position.
1. Properly stop and park unit (See
Operation on page 12).
2. Lower the mower.
3. Place seat in most rearward position.
4. Remove belt covers.
5. Place foot board in open position
(Figure 18).
1
3
2
2
5
4
1
7
6
1.
2.
3.
4.
5.
6.
7.
3
1. Footboard in
open
position
2. Support
Frame
3. Pivot
Figure 18
PTO Mower Belt
Mower Drive Belt
Springs
Mower Drive Belt Idler
PTO Mower Belt Idler
Mower Clutch Sheave
Center Sheave
Figure 19
Replacing Mower Belts
NOTE: Long mower belt must be removed to
remove short mower belt.
Replacing the Hydro Pump Belt
CAUTION: Use care when
releasing idler spring tension.
Keep body parts well away from
idlers when performing this
operation.
1. Slowly release the tension on the long
mower belt idler until all the tension is
removed from the springs.
2. Remove long mower belt from left blade
spindle and remove from deck.
3. Slowly release the tension on the short
belt idler until all the tension is removed
from the springs.
GB - 25
1. Properly stop and park unit (See
Operation on page 12).
2. Remove the PTO belt from the mower
clutch sheave (See Replacing Mower
Belts on page 25).
CAUTION: Use care when
releasing idler spring tension.
Keep body parts well away from
idlers when performing this
operation.
3. Slowly release the tension on the hydro
pump belt idler until all the tension is
removed from the springs.
4. Remove old hydro pump belt from right
hand hydrostat sheave first (Figure 20).
5. Install new hydro pump belt by
positioning belt on sheaves. Put belt
onto right hand hydrostat sheave last.
6. Replace long mower belt on mower
clutch sheave. See Replacing Mower
Belts on page 25.
NOTE: There are four anti-scalp rollers on
the outside of the mower deck and four antiscalp rollers on the inside of the mower deck.
Make sure all anti-scalp rollers are set at the
same height.
Lowest Cutting
Height
1
2
6
Highest
Cutting
Height
5
OF3590
Figure 21
3
Removing the Mower Deck
1. Remove PTO belt (See Replacing
Mower Belts on page 25).
7
4
WARNING: AVOID INJURY.
Mower lift arms and mower lift
pedal could cause severe injury if
they are not locked before
removing the mower deck.
ALWAYS lock mower deck lift
before removing the deck.
8
OF1631
1.
2.
3.
4.
Hydro Belt
Spring
Idler
Engine
Sheave
5. Right Hand
Hydrostat
6. Left Hand
Hydrostat
7. Clutch
8. Clutch
Anchor
2. Lock the mower deck in the service
position.
Push the mower lift pedal forward
between cutting height number 4 and
number 5 to align the holes in the deck
lift shaft and the deck lift cover. Insert the
cutting height pin in the holes on the side
of the deck lift cover so it passes all the
way through the deck lift cover and
shaft.
Figure 20
MOWER DECKS
Anti-scalp Roller Adjustment
The anti-scalp rollers are set at the factory for
typical mowing height, but can be adjusted for
high or low cutting conditions (Figure 21).
Anti-Scalp rollers are intended to prevent
lawn scalping, not to control cutting height.
For a very high cutting height, set the antiscalp rollers in the lowest position on the
bracket.
For a very low cutting height, set the antiscalp rollers in the highest position on the
bracket.
IMPORTANT: The mower lift arms are not
locked unless the cutting height adjustment
pin passes all the way through both the deck
lift cover and shaft.
NOTE: Support the mower deck on blocks or
jack stands before disconnecting link chains
from mower lift arms to prevent the deck from
falling.
3. Remove link chains from mower lift
arms. Note hole location on mower lift
arms for replacement.
GB - 26
4. Remove the mower mounting pins
connecting the mower mounting arms to
the deck.
5. Slide mower deck out from under unit.
Leveling the Mower Deck
These adjustments should be made on a
level surface with the tires inflated to the
correct air pressure.
Check Blade Level and Pitch
1
5
1
2
2
3
4
1. Mower Lift
Arm
2. Link Chain
3. Mower
Mounting
Arm
Figure 22
4. Mower
Mounting
Pin
5. Mower Lift
Arms
Locked
OF3765
Installing the Mower Deck (Figure 22)
1. Slide mower deck under unit.
2. Connect mower mounting arms to deck
with mower mounting pins.
3. Install link chains on the mower lift arms
in the same holes they were removed
from.
4. Install PTO mower belt (See Replacing
Mower Belts on page 25).
5. Level mower deck (See Leveling the
Mower Deck on page 27).
1. Raise mower deck to a 3 in. (7.62 cm)
cutting height.
2. Shut off engine. Engage parking brake.
Remove the ignition key.
NOTE: Place blocks under the bottom edge
of the deck, not under the reinforcement bar
welded along deck face.
3. Place blocks at each corner of the deck
to support the weight of the deck.
4. Turn the blades so the blade ends point
left to right across the width of the deck.
5. Measure the distance between the
ground and cutting edge of the blade on
the left blade (Left position in Figure 23)
and on the right blade (Right position in
Figure 23). Distances should be within
3/16 in. (4.7 mm). If they are not, raise
the low side of the deck using the height
adjusters on the deck lift brackets (see
Figure 24).
6. After deck is level side to side, check the
deck front to back pitch.
7. Turn the blades so the blade ends point
front to back as shown in Figure 23.
8. Measure the distance between the
ground and the cutting edge of the
middle blade at the front of the deck
(Front position in Figure 23) and
between the ground the cutting edge of
the left and right blades at the rear of the
deck (Rear position in Figure 23).
9. The cutting edge at the front of the deck
(Front position in Figure 23) should be
1/8 in. (3.18 mm) lower than the cutting
edges at the rear of the deck (Rear
position in Figure 23).
10. If measurements are out of range, raise
the low side of the deck using the height
adjusters on the deck lift brackets (see
Figure 24). Be sure to raise the deck
evenly to keep the deck level side to
side.
NOTE: Pitching the front of the blades lower
than the rear provides a balance between cut
quality and the power needed to cut grass.
Certain cutting conditions require the deck to
be pitched with the rear of the blades lower
than the front. Heeling the deck this way
requires more engine power but can provide
better cut quality.
11. Remove the blocks from under the deck.
GB - 27
Adjust Blade Height
Blade Side-to-Side Level
Left
Right
Level and pitch the mower with the height
adjusters on each deck lift bracket
(Figure 24).
Loosen the jam nut on the deck lift
bracket bolt about 1/4 turn to reduce
clamp load on the height adjusters.
Loosen the jam nut on the deck adjuster
bolt and then turn the bolt clockwise to
raise the deck or counterclockwise to
lower the deck. Tighten both jam nuts.
Blade Front-to-Back Pitch
Height
Adjusters
Front
Rear
Rear
DO NOT place blocks under
reinforcement bar.
Figure 23
Figure 24
STORAGE
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
SHORT TERM
NEVER spray unit with high-pressure water
or store unit outdoors.
Inspect unit for visible signs of wear,
breakage or damage.
Keep all nuts, bolts and screws properly
tightened and know unit is in safe working
condition.
Store unit in a cool, dry protected area.
LONG TERM
Clean unit thoroughly with mild soap and low
pressure water and lubricate (See Lubricate
Unit on page 22 in Maintenance). Touch up
all scratched painted surfaces.
Remove weight from wheels by putting
blocks under frame or axle.
GB - 28
When storing unit for extended periods of
time, remove all fuel from tank and carburetor
(run dry). Refer to Engine Manual.
Clean and charge the battery. Charge battery
every three to four weeks when storing unit.
Part No.
Description
79206400
Mulching Kit (991039)
Fuel System
79206500
Mulching Kit (991041)
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
To treat the fuel system for storage:
1. Add fuel stabilizer according to
manufacturers’ instructions.
2. Run engine for at least 10 minutes after
adding stabilizer to allow it to reach the
carburetor.
NEVER store the engine with fuel in the fuel
tank inside of a building with potential
sources of ignition.
79100500
Striper Kit
79100800
Discharge Cover Kit (991039)
79206800
Discharge Cover Kit (991041)
79202700
Headlight Kit
To Take the Unit Out of Storage
1. Refer to the engine service manual to
prepare the engine for service.
2. Put fresh, clean fuel in the fuel tank.
3. Begin the maintenance schedule.
4. Charge and install the battery.
ACCESSORIES
SERVICE PARTS
Part No.
Qty
Description
21547700
1
Air Filter - Kohler
21531500
1
Air Filter - Briggs and
Stratton
21531600
1
Air Filter Precleaner Briggs and Stratton
21397200
1
Engine Oil Filter Kohler
21530700
1
Engine Oil Filter Briggs and Stratton
00669300
2
Hydraulic Oil Filter
21541700
2
Spark Plug - Kohler
21531100
2
Spark Plug - Briggs and
Stratton
21541500
1
Fuel Filter - Kohler
21531800
1
Fuel Filter - Briggs and
Stratton
07200026
1
PTO Belt - 52” Decks
07200028
1
PTO Belt - 60” Decks
07211500
1
Traction (Hydro Pump)
Belt
03253800
1
Blade - 52” Decks
03253900
1
Blade - 60” Decks
GB - 29
SPECIFICATIONS
Model Number
Model
991039
991040
Zoom 2452HD
Zoom 2660HD
Engine
Engine
Briggs & Stratton ELS
Engine Model Number
Engine Power – hp (kW) at Maximum
RPM
24 (17.9)
26 (19.4)
Governed RPM (May be different from
maximum RPM)
3600 +/- 100
Liquid or Air Cooled
Air
Cooling System Capacity
NA
Speed
Forward Maximum – mph (km/h)
7.0 (11.3)
Reverse Maximum – mph (km/h)
4.0 (6.4)
Turning Radius
Zero
Brakes
Hydro - Parking
Electrical
Starter
Electric
Battery
12-Volt Maintenance Free
Power Take-Off
Electric PTO Clutch/Brake
Fuel
Fuel Type
Refer to Engine Manual
Fuel Tank Capacity – gal. (L)
7 (26.5)
Transmission
Type
Transmission Oil
Hydrostatic Drive
Mobil 1 15W-50 Synthetic or Equivalent
Hydraulic Oil Filter
Yes
Size and Weight
Length – in. (cm)
Width (With Chute Up) – in. (cm)
71.5 (181.6)
63.0 (160)
63.0 ( 160)
Height – in. (cm)
Weight – lbs (kg)
42 (106)
830 (377)
830 (377)
Tires
Front Tire Size – in. (cm)
Rear Tire Size – in. (cm)
13 x 5-6
20 x 10-10
Front Tire Pressure – psi (kPa)
Rear Tire Pressure – psi (kPa)
20 x 10-10
20 - 25 (138 -172)
15 -18 (103 -124)
15 -18 (103 -124)
Mower Deck
Mower Deck Lift
Cutting Width – in. (cm)
Mechanical
52 (132)
Cutting Height – in. (cm)
60 (152)
1 - 5 (2.5 - 12.7)
Cutting Height Increments – in. (cm)
0.5 (1.25)
GB - 30
Ariens Limited
Warranties
2-Year Limited Lawn and Garden
Consumer Warranty
Ariens Company (Ariens) warrants to the
original purchaser that Ariens and Gravely
brand consumer products manufactured by
Ariens Company will be free from defects in
material and workmanship for a period of two (2)
years after the date of purchase, and that Ariens
will repair any defect in material or workmanship,
and repair or replace any defective part, subject
to the conditions, limitations and exclusions set
forth herein. Such repair or replacement will be
free of charge to the original purchaser (labor
and parts), except as noted below.
The two-year duration of this warranty applies
only if the product is put to ordinary, reasonable,
and usual personal, family, or household uses. If
the product is put to any business, commercial,
or industrial use such as, but not limited to,
commercial landscaping, mowing or snow
removal services, or golf course or park
maintenance, or agricultural or farmstead use,
then the duration of this warranty is ninety (90)
days after the date of purchase, or one (1) year
after the date of purchase if the product is
labeled as a Professional/Commercial Product.
The duration of this warranty shall be ninety (90)
days after the date of purchase if any product is
rented or leased.
2-Year Limited Lawn and Garden
Commercial Warranty
The Ariens Company (Ariens) warrants to the
original purchaser that all Gravely Pro and
ProMaster products manufactured by Ariens will
be free from defects in material and
workmanship for a period of two (2) years after
the date of purchase or 1000 hours of use,
whichever comes first. An authorized Gravely
dealer will repair any defect in material or
workmanship, and repair or replace any
defective part, subject to the conditions,
limitations and exclusions set forth herein. Such
repair or replacement will be free of charge to
the original purchaser (labor and parts), except
as noted below.
The duration of this warranty shall be ninety
(90) days after the date of purchase or 1000
hours of use, whichever comes first, if any
product is rented or leased.
3-Year Limited Sno-Thro Warranty
Ariens Company (Ariens) warrants to the
original purchaser that Sno-Thro products
manufactured by Ariens Company will be free
from defects in material and workmanship for a
period of three (3) years after the date of
purchase, and will repair any defect in material
or workmanship, and repair or replace any
defective part, subject to the conditions,
limitations and exclusions set forth herein. Such
repair or replacement will be free of charge to
the original purchaser (labor and parts), except
as noted below.
The three-year duration of this warranty
applies only if the product is put to ordinary,
reasonable, and usual personal, family, or
household uses. If the product is put to any
business, commercial, or industrial use, then the
duration of this warranty is ninety (90) days after
the date of purchase, or one (1) year after the
date of purchase if the product is labeled as a
Professional/Commercial Product. The duration
of this warranty shall be ninety (90) days after
the date of purchase if any product is rented or
leased.
DURA-CLEAN™ Auger Limited
Lifetime Warranty
Ariens Company (Ariens) warrants to the
original purchaser that the rubber components
of the DURA-CLEAN™ Auger manufactured by
Ariens Company will be free from defects in
material and workmanship and will not wear out
for the life of the Sno-Thro, except as noted
below.
Ariens Company will provide for the
replacement of any of the rubber components of
the DURA-CLEAN™ Auger found upon
examination by the Ariens Company to be
defective or worn out. Replacements will be
supplied free of charge. Labor is not included
after two (2) years from the date of purchase of
the Sno-Thro.
The lifetime limited warranty shall apply if the
product is put to ordinary, reasonable, and usual
personal household use. If the product is put to
any business, commercial, industrial, rental, or
leased use, the warranty shall be against defects
in material and workmanship for ninety (90) days
following the date of purchase.
Ariens Company • 655 W. Ryan St. •
Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com
ALW2-62905
Exceptions, Limitations, Exclusions
These warranties are subject to the following conditions, limitations, and exclusions:
The following items are excluded from this
To obtain warranty service, the following
warranty:
conditions must be met:
• Engines and engine accessories are covered
• The purchaser must perform the
only by the engine manufacturer’s warranty
maintenance and minor adjustments
and are not covered by this warranty.
explained in the owner’s manual.
• Hydro-Gear transmissions and/or
• The purchaser must promptly notify Ariens
Hydro-Gear drive components are covered
Company or an authorized Ariens service
only by the Hydro-Gear warranty and are
representative of the need for warranty
not covered by this warranty.
service.
• Parts that are not genuine Ariens or
• The purchaser must transport the product
Gravely brand service parts are not
to and from the place of warranty service.
covered by this warranty.
• Warranty service must be performed by a
• Except as specifically warranted, normal
respective Ariens or Gravely authorized
maintenance, services, and normal
service representative.
replacement items, such as spark plugs,
• To find an Ariens or Gravely authorized
oil, oil filters, air filters, mufflers, belts, tires,
service representative, contact Ariens at:
shoes, runners, scraper blades, shear
655 W. Ryan St, P.O. Box 157
bolts, mower blades, mower vanes,
Brillion, WI 54110-0157
headlights, light bulbs, knives, etc. are not
(920) 756 - 2141
covered by this warranty except as noted
www.ariens.com
below.
• Mufflers, belts, and tires on consumer lawn
www.gravely.com
and garden products are warranted to the
This warranty is subject to the following
original purchaser for two years.
limitations:
• Friction discs, idlers, cables, and electrical
• Genuine Ariens or Gravely brand service
components on Sno-Thros put to usual
parts and accessories not purchased with
personal household use are warranted to
the product covered by this warranty, but
the original purchaser for two years.
which are later purchased and used with
• Any defect which is the result of misuse,
that product, are warranted to be free from
alteration, improper assembly, improper
defects in material and workmanship for a
adjustment, neglect, or accident is not
period of ninety (90) days after date of
covered by this warranty.
purchase, and Ariens Company will repair
This warranty applies only to products
or replace any such part or accessory free
purchased in the United States (including Puerto
of charge, except for labor, during that
Rico) and Canada. In all other countries, contact
period.
place of purchase for warranty information.
• Batteries are warranted only for a period of
twelve (12) months after date of purchase,
on a prorated basis. For the first ninety (90)
days of the warranty period, a defective
battery will be replaced free of charge. If
the applicable warranty period is more than
90 days, Ariens Company will cover the
prorated cost of any defective battery, for
up to twelve (12) months after the date of
purchase.
Ariens may from time to time change the design of its products. Nothing contained in this warranty
shall be construed as obligating Ariens to incorporate such design changes into previously
manufactured products, nor shall such changes be construed as an admission that previous designs
were defective.
LIMITATION OF REMEDY AND
DAMAGES
DISCLAIMER OF FURTHER
WARRANTY
Ariens Company’s liability under this warranty,
and under any implied warranty that may exist, is
limited to repair of any defect in workmanship,
and repair or replacement of any defective part.
Ariens Company shall not be liable for incidental,
special, or consequential damages (including
lost profits). Some states do not allow the
exclusion of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you.
Ariens Company makes no warranty, express
or implied, other than what is expressly made in
this warranty. If the law of your state provides
that an implied warranty of merchantability, or an
implied warranty of fitness for particular purpose,
or any other implied warranty, applies to Ariens
Company, then any such implied warranty is
limited to the duration of this warranty. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Ariens Company • 655 W. Ryan St. •
Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com
ALW2-62905
Ariens Company
655 West Ryan Street
Brillion, WI 54110-1072
920-756-2141
Fax 920-756-2407
www.ariens.com
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.