Control Panels
D9412GV3/D7412GV3/D7212GV3
en
UL Installation Instructions
Control Panels
Table of Contents | en
3
Table of Contents
1
Installation
4
1.1
Installation Preparation
4
1.2
Enclosure Options
4
1.3
Mounting Enclosure
4
1.4
Installing the Control Panel
5
1.5
Connecting Earth Ground
5
1.5.1
Terminal 10
5
1.5.2
Ground Fault Detect Enable
6
1.5.3
Enabling Ground Fault Detection
6
1.5.4
GV3 Series Ground Fault Specifications
7
1.5.5
Locking the Reset Pin
7
2
Diagrams
8
2.1
Faceplates
8
2.2
Power Supply Side Wiring Diagrams
9
2.2.1
D9412GV3/D7412GV3 Power Supply Side Wiring Diagram (D9412GV3 shown)
9
2.2.2
D7212GV3 Power Supply Side Wiring Diagram
10
2.3
Input Points and Peripheral Devices Wiring Diagram (D9412GV3 shown)
11
2.4
SDI Devices Wiring Diagrams
12
2.4.1
D9412GV3 SDI Devices Wiring Diagram
12
2.4.2
D7412GV3 SDI Devices Wiring Diagram
13
2.4.3
D7212GV3 SDI Devices Wiring Diagram
14
2.5
Keyswitch Wiring
15
3
Power Supply and Power Outputs
16
3.1
Power Supply - Primary
16
3.1.1
Primary (AC) Power Circuit
16
3.1.2
Installing the Transformer
16
3.2
Power Terminals - Secondary
17
3.2.1
Secondary (DC) Power
17
3.2.2
Installing the Battery
17
3.3
Power Outputs - Circuit Protection
19
3.4
Power Outputs - Total Available Power
19
3.5
Power Outputs - Continuous Power Output Terminals 3, 8, 24, and 32
20
3.6
Power Outputs - Programmable Power Output Terminals 6, 7, and 8
20
3.6.1
Programming
20
3.6.2
Terminals 6 and 7
20
3.6.3
Fire System Power Formula
21
3.6.4
Terminal 8
21
4
Specifications
22
4.1
Terminal Wiring Requirements
23
4.2
Compatible Accessories
25
4.3
Circuit Classes
26
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
4
en | Installation
Control Panels
1
Installation
1.1
Installation Preparation
This section contains a general installation procedure and refers to other sections of the
document for detailed instructions. Review this document and the D9412GV3/D7412GV3
Program Entry Guide (P/N: F01U170807) or D7212GV3 Program Entry Guide
(P/N: F01U170808) before beginning the installation to determine the hardware and wiring
requirements for the features used. Have the following documentation available when reading
through this guide:
–
D9412GV3/D7412GV3 Program Record Sheet (P/N: F01U170809) or D7212GV3 Program
Record Sheet (P/N: F01U170810)
–
Security System Owner's Manual (P/N: 71-06633-000) and GV3 Series Owner's Manual
Supplement (P/N: F01U143082)
–
Installation manual for keypad or annunciator (D1255 all models, D1255RB, D1256,
D1256RB, D1257, D1257RB, or D1260 all models)
1.2
Enclosure Options
Mount the control panel assembly in any of the Bosch Security Systems, Inc. enclosures
listed:
–
D8103 Universal Enclosure (tan)
–
D8109 Fire Enclosure (red) for the D9412GV3 and D7412GV3 Control Panels
–
D8108A Attack Resistant Enclosure (tan)
Refer to the D9412GV3/D7412GV3 Approved Applications Compliance Guide
(P/N: F01U143069) or D7212GV3 Approved Applications Compliance Guide (P/N: F01U143080)
to determine if the application requires a specific enclosure.
1.3
Mounting Enclosure
1.
Run the necessary wiring throughout the premises.
2.
Mount the enclosure in the desired location. Use all five enclosure mounting holes. Refer
to Figure 1.1, Page 5.
3.
Pull the wires into the enclosure.
NOTICE!
Electromagnetic interference (EMI) can cause problems on long wire runs.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
Installation | en
5
Figure 1.1 Enclosure Mounting
Callout
1
2
3
4
5
6
7
8
9
1.4
Description
Point chart label
Mounting skirt hooks (2)
Module mounting holes (12)
Tamper switch mounting holes (5)
Skirt mounting hole (1)
Enclosure mounting holes (5)
Mounting skirt hook holes (2)
Back of the control panel
Lock down tab
Installing the Control Panel
1.
Place the control panel over the inside back of the enclosure, aligning the large
rectangular openings of the mounting skirt with the mounting hooks of the enclosure.
Slide the control panel down so that it hangs on the hooks. Refer to Figure 1.1, Page 5.
2.
Remove the tape from the #6 x 1/4-in. screw in the mounting tab on the control panel.
The screw passes through the mounting tab and into the skirt mounting hole in the
enclosure. Tighten the screw to secure the control panel in the enclosure.
3.
Connect earth ground to the control panel before making any other connections. Refer to
Section 1.5 Connecting Earth Ground, page 5.
1.5
Connecting Earth Ground
1.5.1
Terminal 10
To help prevent damage from electrostatic charges or other transient electrical surges,
connect the system to earth ground at Terminal 10 before making other connections.
Recommended earth ground references are a grounding rod or a cold water pipe.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
6
en | Installation
Control Panels
WARNING!
Do not use telephone or electrical ground for the earth ground connection. Use 1.8 mm (14
AWG) to 1.5 mm (16 AWG) wire when making the connection. Do not connect other control
panel terminals to earth ground.
1.5.2
Ground Fault Detect Enable
NOTICE!
To meet UL 864 requirements, enable Ground Fault Detect.
A ground fault is a circuit impedance to earth ground. The control panel has a ground fault
detection circuit that, when enabled, detects ground faults on Terminals 1 to 9 and 11 to 32.
The control panel also detects and annunciates ground faults on any device connected to it.
If a ground fault condition occurs, the keypads display SERVC GND FAULT and the control
panel sends a GROUND FAULT TROUBLE, AREA 1. When the control panel recognizes that the
ground fault condition is corrected, and remains corrected for between 5 to 45 consecutive
seconds, a Restoral Report is sent.
NOTICE!
The D9412GV3/D7412GV3/D7212GV3 Control Panels log and print a Ground Fault event as a
Trouble Point 256 if communicating in Modem IIIa2 format. If communicating in Contact ID
format, the D7212GV3 generates a Ground Fault (310) event.
1.5.3
Enabling Ground Fault Detection
To enable the Ground Fault Detect Enable feature, lock (close) the S4 Ground Fault Detect
Pin on the control panel (refer to Figure 1.2, Page 6).
Figure 1.2 Ground Fault Detect (S4)
Callout
1
2
Description
S4 Locked (Closed). Control panels detects ground faults.
S4 Unlocked (Open). Control panel does not detect ground faults.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
1.5.4
Installation | en
7
GV3 Series Ground Fault Specifications
Table 1.1, Page 7 provides the impedance specifications for detecting ground faults when any
terminal or field wiring is shorted to ground.
Impedance
Control Panel Detects Ground Fault
≤ 300 Ω
Yes
300 Ω to 200 k Ω
Detection depends upon the terminal
≥ 200 k Ω
No
Table 1.1
Ground Fault Impedance Specifications
1.5.5
Locking the Reset Pin
Locking the reset pin disables the control panel (refer to Figure 1.3, Page 7). When the control
panel is disabled, the system ignores the keypads and points. CALL FOR SERVICE appears in
keypad displays when the pin is locked down.
On-board relays (Terminals 6 and 7) and off-board relays deactivate when the control panel is
reset. Terminal 8 has power when the relay is deactivated. Activation interrupts power at that
terminal. The on-board relay (Terminal 8) remains deactivated when the reset pin is locked in
the disable position.
Releasing the reset pin from the closed position resets the control panel. The control panel
resets all its timers, counters, indexes, and buffers. Any points that restore after a reset do
not generate Restoral Reports.
If the reset pin is placed in the disable position when all areas are armed, there must be an
entry in the Answer Armed program item. Refer to RPS Parameters in the D9412GV3/
D7412GV3 Program Entry Guide (P/N: F01U170807) or the D7212GV3 Program Entry Guide (P/
N: F01U170808).
Locking the pin in the disable position applies power to the control panel and charges the
battery while the detection devices and keypads are installed.
When the Reset Switch (labeled S1) is closed, the communication module at SDI Address 92
is disabled. While in this mode, remote programming communication is only supported by the
communication module at SDI Address 88.
Figure 1.3 Reset Pin
Callout
1
2
Description
Reset pin locked (closed)
Reset pin normal (open)
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
8
en | Diagrams
Control Panels
2
Diagrams
2.1
Faceplates
Callout
1
2
3
4
5
6
7
Description
Charging status LED (yellow)
Low battery LED (red)
Color-coded battery leads
Ground fault detect enable
Phone LED (red)
Tip
Telephone cord connector
F.01U.167.105 | 02 | 2010.11
Callout
8
9
10
11
12
13
14
Description
Ring
S3, Point 8 EOL selection
Operation monitor LED (green)
Accessory connector
Programming connector
Reset pin
SDI quick connector
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
Diagrams | en
2.2
Power Supply Side Wiring Diagrams
2.2.1
D9412GV3/D7412GV3 Power Supply Side Wiring Diagram
(D9412GV3 shown)
Callout
1
Description
Callout
If required by local AHJ, connect D113 Battery 9
Description
To Relay A or Relay B
2
Lead Supervision Module.
Batteries
Listed Audible Signaling Devices rated at
10
9
12.0 VDC nominal (do not use vibrating type
11
12
horns)
C900V2 (optional)
RJ31X, secondary phone line
3
4
D122 Dual Battery Harness, as required
D1640 Transformer and D8004 Transformer
5
Enclosure required for NFPA Applications
D8132 Dual Battery Charger with two batteries 13
560 Ω, 2 W EOL Resistor (P/N: 15-03130-005)
6
7
8
(Batteries are not supervised.)
Power limited, supervised
Power limited
D192G Bell Supervision Module
RJ31X, primary phone line
D928
To earth ground
14
15
16
NOTICE!
All external connections except Terminal 5 (battery positive) are power limited.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
10
en | Diagrams
2.2.2
Control Panels
D7212GV3 Power Supply Side Wiring Diagram
Callout
1
Description
If required by local AHJ, connect D113
Callout
8
Description
D192G Bell Supervision Module
2
3
Battery Lead Supervision Module.
Batteries
D122 Dual Battery Harness, as required
9
10
To Relay A or Relay B
Listed Audible Signaling Devices rated at 12.0
4
D1640 Transformer and D8004 Transformer 11
VDC nominal (Do not use vibrating type horns.)
C900V2 (optional)
5
Enclosure required for NFPA Applications
D8132 Dual Battery Charger with two
12
560 Ω, 2 W EOL Resistor (P/N: 15-03130-005)
6
7
batteries (Batteries are not supervised.)
Power limited, supervised
Power limited
13
14
RJ31X, primary telephone line
To earth ground
NOTICE!
All external connections except Terminal 5 (battery positive) are power limited.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
2.3
Diagrams | en
11
Input Points and Peripheral Devices Wiring Diagram
(D9412GV3 shown)
Callout
1
Description
(Optional): For 24 V applications use a UL 1481 Listed regulated, power-limited 24 VDC power supply
2
3
4
wiring requirements.
D130 Relay Module
D125B Powered Loop Interface Module
To UL Listed two-wire smoke detectors. Refer to Two-Wire Smoke Detectors in the D9412GV3/D7412GV3
5
6
detectors.
P105BL1 1 kΩ EOL resistor (P/N: F01U033966): For typical burglar alarm applications.
D129 Dual Class A Initiation Circuit Module: Provides optional Waterflow Alarm Retard feature. Not
with a D130 Relay Module. Refer to the D130 Installation Instructions (P/N: F01U072455) for correct
Approved Applications Compliance Guide (P/N: F01U143069) for a listing of compatible two-wire smoke
suitable for two-wire smoke detectors.
NOTICE!
Use zero retard except for waterflow devices.
All external connections except Terminal 5 (battery positive) are power limited.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
12
en | Diagrams
Control Panels
2.4
SDI Devices Wiring Diagrams
2.4.1
D9412GV3 SDI Devices Wiring Diagram
Callout
1
Description
Callout
8
Description
D8125 POPEX No. 2
9
10
Up to 119 D9127U/T POPITs
Zonex 1: 15 D8128Ds maximum2
2
3
Up to 16 supervised keypads or fire annunciators1
Up to 8 D9210B Access Control Interface Modules
Up to 3 supervised 9131A Parallel Printer Interface
4
Modules, or other SDI devices
Power limited, supervised
11
Zonex 2: 15 D8128Ds maximum2
5
Power limited
12
Zonex 1: Up to 8 D8129s maximum2
6
DX4020 Network Interface Module or other SDI device
13
Zonex 2: Up to 8 D8129s maximum2
7
D8125 POPEX No. 1
1 D1255 (all models), D1255RB, D1256, D1256RB Keypads, or D1257RB or D1257 Fire Annunciators, or up to 8 D1260 Keypads (all
models).
2 The number of D8129 OctoRelays that can be connected to each zonex terminal on the control panel is limited by the number of
D8128D OctoPOPITs connected to the same terminal. Refer to the D8128D Installation Guide (P/N: F01U070537) or the D8129
Operation and Installation Guide (P/N: F01U036302) for specific information.
NOTICE!
All external connections except Terminal 5 (battery position) are power limited.
Fire and Intrusion devices must be on separate circuits. Refer to ICP-SDI-9114 Installation
Instructions (P/N: F01U030068).
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
2.4.2
Callout
1
2
3
4
5
6
7
8
9
10
Diagrams | en
13
D7412GV3 SDI Devices Wiring Diagram
Description
Up to 16 supervised keypads or fire annunciators1
Up to 2 D9210B Access Control Interface Modules
Up to 1 supervised 9131A Parallel Printer Interface Module, or other SDI device
Power limited, supervised
DX4020 Network Interface Module or other SDI device
Power limited
D8125 POPEX No. 1
Up to 67 D9127U/T POPITs
Zonex 1: Up to 9 D8128Ds maximum2
Zonex 1: Up to 8 D8129s maximum2
1 D1255 (all models), D1255RB, D1256, D1256RB Keypads, or D1257RB or D1257 Fire Annunciators, or up to 8 D1260 Keypads (all
models).
2 The number of D8129 OctoRelays that can be connected to each zonex terminal on the control panel is limited by the number of
D8128D OctoPOPITs connected to the same terminal. Refer to the D8128D Installation Guide (P/N: F01U070537) or the D8129
Operation and Installation Guide (P/N: F01U036302) for specific information.
NOTICE!
All external connections except Terminal 5 (battery position) are power limited.
Fire and Intrusion devices must be on separate circuits. Refer to ICP-SDI-9114 Installation
Instructions (P/N: F01U030068).
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
14
en | Diagrams
2.4.3
Callout
1
2
3
4
5
6
7
8
9
Control Panels
D7212GV3 SDI Devices Wiring Diagram
Description
Up to 8 supervised keypads or fire annunciators1
Power limited, supervised
D9131A Parallel Printer Interface Module or other SDI device
DX4020 Network Interface Module or other SDI device
Power limited
D8125 POPEX No. 1
Up to 32 D9127U/T POPITs
Zonex 1: up to four D8128Ds maximum2
Zonex 1: up to three D8129s maximum2
1 D1255 (all models), D1255RB, D1256, D1256RB, D1260 (all models) Keypads, or D1257RB or D1257 Fire Annunciators.
2 The number of D8129 OctoRelays that can be connected to each zonex terminal on the control panel is limited by the number of
D8128D OctoPOPITs connected to the same terminal. Refer to the D8128D Installation Guide (P/N: F01U070537) or the D8129
Operation and Installation Guide (P/N: F01U036302) for specific information.
NOTICE!
All external connections except Terminal 5 (battery position) are power limited.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
2.5
Diagrams | en
15
Keyswitch Wiring
Callout Description
1
Maintained keyswitch
2
Momentary keyswitch
3
Common
4
Point Input
5
1 kΩ or 33 kΩ resistor*
6
Open on a circuit arms the area
7
Short on a circuit toggles the arming state
*Use 1 kΩ EOL resistors if using one of the zones on the control panel or an OctoPOPIT. Use a 33 kΩ resistor if using a POPIT.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
16
en | Power Supply and Power Outputs
Control Panels
3
Power Supply and Power Outputs
3.1
Power Supply - Primary
3.1.1
Primary (AC) Power Circuit
The primary source is a 16.5 VAC, 40 VA, internally-fused transformer (Bosch Security
Systems, Inc. Model D1640). The control panel draws 200 mA when idle and 300 mA when in
an alarm state. The total available auxiliary current is 1.4 A. Transient suppressors and spark
gaps protect the circuit from power surges. This protection relies on the ground connection at
Terminal 10. Ensure that you connect Terminal 10 to a proper ground. Refer to
Section 1.5 Connecting Earth Ground, page 5.
AC Power Fail
The system indicates an AC power failure when Terminals 1 and 2 do not have power. The AC
Fail Time parameter sets the number of minutes or seconds without AC power before the
control panel acknowledges the failure and the number of minutes or seconds after the power
returns before the control panel acknowledges restored power.
Refer to the D9412GV3/D7412GV3 Program Entry Guide (P/N: F01U170807) or the
D7212GV3 Program Entry Guide (P/N: F01U170808) for additional information about AC Fail
Time and UL 864 requirements.
3.1.2
Installing the Transformer
NOTICE!
Do not short-circuit the terminals of the transformer: Shorting the terminals opens the
internal fuse, causing permanent failure. Connect the transformer to Terminals 1 and 2 of the
control panel before plugging it into the power source.
1.
Use 1.22 mm (18 AWG) wire (minimum) to connect the transformer to the control panel.
The wire length should be as short as possible. The maximum length is 15 m (50 ft).
Connect the battery and plug in the transformer.
2.
Route telephone and sensor loop wiring away from any AC conductors, including the
transformer wire.
AC wiring can induce noise and low level voltage into adjacent wiring. Route data wiring
away from AC and telephone wiring.
NOTICE!
Always connect the battery first and then plug in the transformer.
3.
Connect the battery. Refer to Section 3.2.2 Installing the Battery, page 17.
4.
Plug the transformer into an unswitched, 120 VAC 60 Hz power outlet only.
5.
Secure the transformer to the outlet with the screw provided.
D8004 Transformer Enclosure Required for Fire Systems
Use the D8004 Transformer Enclosure for the D1640 Transformer in fire and combined fire
and burglary applications.
NOTICE!
Check with the Authority Having Jurisdiction (AHJ) about mounting transformers on specific
circuits.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
Power Supply and Power Outputs | en
3.2
Power Terminals - Secondary
3.2.1
Secondary (DC) Power
17
A 12 V, 7 Ah (up to 14 Ah) sealed lead-acid rechargeable battery supplies secondary power for
auxiliary and alarm outputs, and powers the system during interruptions in primary (AC)
power.
WARNING!
Use Lead Acid Batteries Only: The charging circuit is calibrated for lead-acid batteries. Do not
use gel-cell or nicad batteries.
Extra Batteries Increase Back-up Time
To increase battery back-up time, connect a second 12 V battery in parallel to the first battery.
Use a D122 Dual Battery Harness to ensure proper and safe connection. Refer to the Standby
Battery and Current Rating Chart in the D9412GV3/D7412GV3 Approved Applications
Compliance Guide (P/N: F01U143069) or in the D7212GV3 Approved Applications Compliance
Guide (P/N: F01U143080) for battery standby time calculations.
D1218 Battery
The D1218 is a 12 V, 18 Ah battery for use in applications requiring extended battery standby
time. Up to two D1218 batteries can be connected when used with a D122 Dual Battery
Harness.
WARNING!
When connecting two D1218 Batteries to the control panel, both must have the same capacity
(use two 17.2 Ah batteries or two 18 Ah batteries).
NOTICE!
When using two D1218 batteries, use a separate enclosure, a D122L Dual Battery Harness,
and long leads.
3.2.2
Installing the Battery
1.
Place the battery upright in the base of the enclosure.
2.
Locate the red and black leads supplied in the literature pack.
3.
Connect the black battery lead to Terminal 4, and then to the negative (-) side of the
battery.
4.
Connect the red battery lead to Terminal 5, and then to the positive (+) side of the
battery.
WARNING!
High current arcs are possible. The positive (red) battery lead and Terminal 5 can create high
current arcs if shorted to other terminals or the enclosure. Use caution when working with the
positive lead and Terminal 5. Always disconnect the positive (red) lead from the battery
before removing it from Terminal 5.
WARNING!
The battery terminals and wire are not power limited. A 6.4 mm (0.250 in.) space must be
maintained between the battery terminals, battery wiring, and all other wiring. Battery wiring
cannot share the same conduit, conduit fittings, or conduit knock-outs with other wiring.
Refer to Figure 3.1, Page 18.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
18
en | Power Supply and Power Outputs
Control Panels
Figure 3.1 Battery Terminals
Callout
1
Description
Battery terminals. Terminal 5 is non-power limiting.
Figure 3.2 Non-Power-Limited Wiring
Callout
1
2
3
4
5
6
Description
Conduit required for use with external batteries.
Battery wires
6.4 mm (0.25 in.) minimum. To ensure proper spacing, use tie-wraps or similar devices to secure wires.
Relay output wires
Input or Zone wires
Standby battery
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
3.3
Power Supply and Power Outputs | en
19
Power Outputs - Circuit Protection
Three self-resetting circuit breakers protect the control panel from short circuits on the
continuous and programmable power outputs. If the control panel is programmed for power
supervision and a short circuit occurs on one of the power outputs, the control panel sends a
BATTERY LOW or BATTERY MISSING for Bosch Security Systems Modem IIIa2 Communication
Format, or a Battery Missing/Dead (311) or Low System Battery (302) for Contact ID Format.
One self-resetting circuit breaker protects:
–
Terminal 3: Auxiliary Power
–
Terminal 24: Zonex Power.
NOTICE!
A short circuit on one terminal disrupts power to the other terminal.
Another self-resetting circuit breaker protects:
–
Terminal 6: Alarm Power Output
–
Terminal 7: Alternate Alarm Power Output
–
Terminal 8: Switched Auxiliary Power.
NOTICE!
A short circuit on one of the terminals disrupts power to the other two terminals.
The third self-resetting circuit breaker protects Terminal 32: Power +.
NOTICE!
UL requires any device powered from a power output to be supervised.
NOTICE!
UL requires that power outputs are not shared between fire and non-fire devices unless all
devices are in conduit within 20 ft and are in the same room.
3.4
Power Outputs - Total Available Power
The system produces up to 1.4 A of combined power at 12.0 VDC Nominal for all powered
devices. The outputs listed below share the available power. These outputs are shown as red
circles on the faceplate.
–
Terminal 3 - Auxiliary Power. Use this terminal to power devices requiring continuous
power.
–
Terminal 6 (Relay A) - Alarm Power Output. Programmable relay normally open, power
on alarm.
–
Terminal 7 (Relay B) - Alternate Alarm Power Output. Programmable relay normally
open, power on alarm.
–
Terminal 8 (Relay C) - Switched Auxiliary Power. Programmable relay normally closed,
switches power off when the Sensor Reset command is executed.
–
Terminal 24 - Zonex Power. Use this terminal to power Zonex modules such as the
D8125, D8128D, and D8129 Modules.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
20
en | Power Supply and Power Outputs
–
Control Panels
Terminal 32 - SDI Power +. Use this terminal to power serial device interface (SDI)
devices such as keypads, the D9131A Parallel Printer Interface Module, and the D9210B
Wiegand Control Interface Module.
3.5
Power Outputs - Continuous Power Output Terminals 3, 8, 24,
and 32
The continuous current draw for powered devices connected to Terminals 3, 8, 24, and 32,
and the accessory connector must not exceed 1.4 A. Devices powered from these outputs
must operate at 12.0 VDC Nominal.
Power Restricted for Fire and Combined Fire and Burglary Systems
Use the Fire System Power Formula to calculate the current available for fire and combined
fire and burglary systems (refer to Section 3.6 Power Outputs - Programmable Power Output
Terminals 6, 7, and 8, page 20).
3.6
Power Outputs - Programmable Power Output Terminals 6, 7,
and 8
3.6.1
Programming
The power outputs at Terminals 6, 7, and 8 are programmed as Relays A, B, and C. All relays
are programmed in the Relays section. Relays are assigned a relay type, (Fire Bell, for
example) when they are assigned to an area. Relays can be assigned to one or more areas.
The Bosch defaults set Relay A (Terminal 6) as a Steady Alarm Bell output, Relay B (Terminal
7) as a Pulsed Fire Bell output, and Relay C (Terminal 8) as a Verification or Reset output for
smoke detectors. The D9412GV3/D7412GV3 Program Entry Guide (P/N: F01U170807) and the
D7212GV3 Program Entry Guide (P/N: F01U170808) contain complete instructions for
programming relays. Refer to Section 3.6.2 Terminals 6 and 7, page 20, Section 3.6.3 Fire
System Power Formula, page 21, and Section 3.6.4 Terminal 8, page 21 for descriptions of the
functions of each terminal. Refer to the Bell Parameters section of the program to set the Fire
Bell, Alarm Bell output responses for relays. Four annunciation patterns are available: Steady,
Pulsed, California Standard, and Temporal Code 3.
Voltage Output at Terminals 6, 7, and 8
If Terminals 6, 7, and 8 do not provide the expected output, check:
–
Programming for Relays A, B, and C in the relays section of the program.
–
Bell Parameters section of the program to confirm that the Alarm and Fire Bell responses
are programmed for the expected duration and pattern.
–
Point Assignments section to confirm that each point is programmed for the expected
local response.
3.6.2
Terminals 6 and 7
When activated, Terminals 6 (Relay A) and 7 (Relay B), provide positive (+) 12.0 VDC Nominal
power output. Use the power at Terminals 6 and 7 to power bells, siren drivers, piezoelectric
fire sounders, electronic horns, or other devices.
Programming determines the format of the output and the conditions that activate it. One
self-resetting circuit breaker protects Terminals 6, 7, and 8 against shorts. When using Relay A
or Relay B to activate notification appliance circuits in UL Listed fire alarm applications, install
a D192G Indicating Circuit Module.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
Power Supply and Power Outputs | en
21
Available Power
The system combines the 1.4 A of primary power produced by the power supply with the
secondary power source (the battery) to produce a total of 2.0 A of alarm power at 12.0 VDC
Nominal. Terminals 6 and 7 share the available alarm power.
Power Restricted for Fire and Combined Fire and Burglary Systems
Fire systems are prohibited from using the battery for determining alarm power. Use the fire
system power formula described in Section 3.6.3 Fire System Power Formula, page 21 to
calculate the current available for fire and combined fire and burglary systems.
3.6.3
Fire System Power Formula
To calculate the current available at Terminals 6 and 7 for fire and combined fire and burglary
systems:
1.
Add together the current draws for all devices connected to Terminals 3, 8, 24, and 32,
and the accessory connector. This is the total current required for the normal standby
condition (NSC).
2.
The current available for NSC is 1.4 A. Subtract the NSC current required calculated in
Step 1 from the NSC current available, 1.4 A. The difference is the alarm current available
for Terminals 6 and 7.
In formula format:
1.4 A - NSC current required (Step 1) = Alarm current available
Refer to the D9412GV3/D7412GV3 Approved Applications Compliance Guide (P/N:
F01U143069) or the D7212GV3 Approved Applications Compliance Guide
(P/N: F01U143080) for module or accessory current requirements.
3.6.4
Terminal 8
Terminal 8 provides continuous positive (+) 12.0 VDC Nominal power. Relay C interrupts the
power at Terminal 8 when activated. Use Terminal 8 to power smoke detectors or other
devices that are reset by interrupting power. One self-resetting circuit breaker protects
Terminals 6, 7, and 8 against shorts.
Verification/Reset Relay
The default program sets Relay C (Terminal 8) as a verification and reset relay. Refer to Relay
Parameters and Point Assignments in the D9412GV3/D7412GV3 Program Entry Guide (P/N:
F01U170807) or in the D7212GV3 Program Entry Guide (P/N: F01U170808) for instructions on
programming verification/reset relays and points.
Performing a sensor reset at a keypad produces a five-second relay activation of verification/
reset relays. The control panel ignores verification and reset points during the five-second
relay activation.
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
22
en | Specifications
4
Voltage Input
Control Panels
Specifications
Primary:
(Power Supply)
Terminals 1
16.5 VAC 40 VA class 2 plug-in transformer (D1640)
and 2
Secondary:
Terminals 4
Sealed lead-acid rechargeable battery (12.0 VDC, 7 Ah or
and 5
12.0 VDC, 17.2 or 18 Ah). The control panel supports up to two
12.0 VDC, 7 Ah batteries using the D122 Dual Battery Harness or
two D1218 (12.0 VDC, 17.2 or 18 Ah) batteries using a D122.
Current
Control Panel: Idle 225 mA; Alarm 300 mA Refer to the Current Rating Chart for Standby Battery
Requiremrent
Calculations section in the D9412GV3/D7412GV3 Approved Applications Compliance Guide
(P/N: F01U143069) or in the D7212GV3 Approved Applications Compliance Guide (P/N:
F01U143080) for the current draw requirements of other system components.
Power
All external connections are power-limited except battery terminals.
Outputs*
Continuous
Terminals 3,
1.4 A maximum at 12.0 VDC nominal (continuous supply) total for
Power
24, and 32
all devices and outputs supplied at Terminals 3, 24, and 32 and at
Outputs
the accessory and programming connectors.
Alarm Power
Terminals 6
2.0 A maximum at 12.0 VDC nominal output. Output can be steady
Output
and 7
or one of three pulsed patterns depending on programming. Refer
to Relays in the D9412GV3/D7412GV3 Program Entry Guide
(P/N: F01U170807) or in the D712GV3 Program Entry Guide
(P/N: F01U170808).
Switched Aux
Power
Terminal 8
1.4 A maximum at 12.0 VDC nominal output. Continuous output is
interrupted by Sensor Reset or alarm verification depending on
programming. Refer to Relays in the D9412GV3/D7412GV3
Program Entry Guide (P/N: F01U170807) or in the D7212GV3
Program Entry Guide (P/N: F01U170808).
Fire and Fire/
To comply with UL 985 and 864 listing standards for fire alarm systems
Burglary
(effective March 1, 1989), the total combined continuous and alarm current
Systems
draw for the system during alarm conditions must be limited to 1.4 A provided
by the primary power supply (rectified AC). If current draw for the system
exceeds 1.4 A, remove connected devices until the current draw falls below 1.4
A. Then, connect the removed devices to a D8132 Battery Charger Module or to
an external power supply (refer to Section 2.5 Keyswitch Wiring, page 15).
*For UL 864 applications, refer to Section 4.2 Compatible Accessories, page 25 for compatible devices.
Minimum
10.2 VDC
Operating
Voltage
SDI Bus
SDI Bus A (+):
9 VDC 4572 m (15000 ft) maximum
SDI Bus B (-):
9 VDC 4572 m (15000 ft) maximum
Telephone
Connection:
RJ31X or RJ38X jack can connect the control panels.
Connections
Two telco
Bosch Security Systems, Inc. D928 Dual Phone Line Module required for two
lines:
phone line service. Supervision supplied by the control panel.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
Specifications | en
Battery
Discharge
13.9 VDC
Charging float level.
Discharge/
Cycle
13.8 VDC
Charging status LED on.
Recharge
12.1 VDC
Schedule
23
Low Battery and AC Fail Reports if programmed. Low Battery LED
on.
10.2 VDC
Minimum operational voltage.
10.0 VDC
Battery load shed (processing functions continue if AC is
present).
Recharge
AC ON
Cycle
Environmental
Load shed relay resets, battery charging begins, Battery Trouble
and AC Restoral Reports sent.
13.7 VDC
Battery Restoral Report sent, Low Battery LED off.
13.9 VDC
Charging status LED off, battery float charged.
Temperature:
0°C to +50°C (+32°F to +122°F)
Relative
Maximum 93% non-condensing
Humidity:
Arming
D720/D720B Keypads, D1255/D1255B/D1255RB Keypads, D1256/D1256RB Fire Command
Stations
Centers; D1257/D1257RB Fire Alarm Annunciators; D1260/D1260B Keypads; Keyswitch
Point
On-board
Open
Greater than 3.7 VDC, but less than 5.0 VDC. Greater than 2.0
Thresholds
Points 1 to 8
Normal
VDC, but less than 3.0 VDC. Greater than 0.0 VDC, but less than
Short
1.3 VDC.
Compatible
D8103 Universal Enclosure, D8109 Fire Enclosure, D8108A Attack Resistant Enclosure, BATB-40
Enclosures
Battery Box
4.1
Terminal Wiring Requirements
Terminal Terminal
Requirements
No
Description
1
AC
18 AWG min (up to 14 AWG max)
2
AC
18 AWG min (up to 14 AWG max)
3
+ AUX POWER
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on current
4
BATTERY -
Bosch supplied wire lead, included with panel
5
BATTERY +
Bosch supplied wire lead, included with panel
6
RELAY A
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on current
7
RELAY B
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on current
8
RELAY C
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on current
9
COMMON
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on current
10
EARTH
14 to 16 AWG
GROUND
11
POINT 1
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
12
13
POINT 1/2
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
COMMON
resistance less than 100 Ω
POINT 2
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
14
POINT 3
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
Bosch Security Systems, Inc.
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
24
en | Specifications
Terminal Terminal
Control Panels
Requirements
No
Description
15
POINT 3/4
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
COMMON
resistance less than 100 Ω
16
POINT 4
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
17
POINT 5
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
18
19
POINT 5/6
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
COMMON
resistance less than 100 Ω
POINT 6
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
20
POINT 7
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
21
22
POINT 7/8
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
COMMON
resistance less than 100 Ω
POINT 8
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop
resistance less than 100 Ω
23
ZONEX
22 AWG min (up to 14 AWG max)
COMMON
24
ZONEX POWER 22 AWG min (up to 14 AWG max)
25
ZONEX IN 2*
22 AWG min (up to 14 AWG max)
26
ZONEX OUT 2*
22 AWG min (up to 14 AWG max)
27
ZONEX IN 1
22 AWG min (up to 14 AWG max)
28
ZONEX OUT 1
22 AWG min (up to 14 AWG max)
29
SDI COMMON
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on peripheral
device current
30
SDI DATA
22 AWG min (up to 14 AWG max)
BUS B
31
SDI DATA
22 AWG min (up to 14 AWG max)
BUS A
32
SDI POWER
Terminal accommodates 14 to 22 AWG, use appropriate wire size based on peripheral
device current
*D9412GV3 only. Terminals 25 and 26 are NOT USED on D7412GV3 and D7212GV3 Control Panels.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Control Panels
4.2
Specifications | en
25
Compatible Accessories
NOTICE!
Where the fire alarm transmitter is sharing on-premise communications equipment, the
shared equipment must be UL Listed (ITE or fire protective signaling).
Model
Title
UL 864
Fire
Intrusion
D122/D122L
Dual Battery Harness
X
X
X
D125B
Powered Loop Interface Module
X
X
X
D127
Reversing Relay
X
X
X
D129
Dual Class A Initiation Circuit Module
X
X
X
D130
Relay Module
X
X
X
D185
Reverse Polarity Module
X
X
D192G
Bell Circuit Supervision Module
X
X
D279A
X
Independent Zone Control (On-Board and OctoPOPIT
X
Points)
D720R
LED Keypad (red)
X
X
D720W
LED Keypad (white)
X
X
D928
Dual Phone Line Switcher
X
X
X
D1255RB
Fire Keypad
X
X
X
D1256RB
Fire Keypad
X
X
X
D1257RB
Fire Alarm Annunciator
X
X
X
D1218
12 V, 17.2 Ah Rechargeable Battery
X
X
X
D1255/D1255B
Keypads (General Purpose)
X
X
D1255R
Text Keypad (red)
X
X
D1255W
Text Keypad (white)
X
X
D1256
Fire Keypad
X
D1257
Fire Alarm Annunciator
X
D1260/D1260B1
Keypads
X
X
D1640
16.5 VAC 40 VA Transformer
X
X
X
D8004
Transformer Enclosure
X
X
X
D8125
POPEX Module
X
X
X
D8125MUX
Multiplex Bus Interface
X
X
X
D8128D
OctoPOPIT Module
X
X
X
D8129
OctoRelay Module
X
X
X
D8130
Release Module
X
X
X
D8132
Battery Charger Module
X
X
D9127U/T
POPIT Module
X
X
D9131A
Parallel Printer Interface Module
X
X
D9210B
Access Control Interface Module
X
X
X
DX4020
Network Interface Module
X
X
X
ITS-DX4020-G
GPRS/GSM Communicator
X
X
X
ICP-SDI-9114
SDI Splitter
X
X
X
Bosch Security Systems, Inc.
X
UL Installation Instructions
F.01U.167.105 | 02 | 2010.11
26
en | Specifications
Control Panels
Model
Title
ZX776Z
PIR Motion Sensor [15 m (50 ft)] with POPIT
X
ZX794Z
PIR Motion Sensor [24 m (80 ft)] with POPIT
X
PIR/Microwave Motion Sensor [+1.7?C (+35?F)] with
X
ZX865
UL 864
Fire
Intrusion
POPIT
ZX938Z
ZX970
PIR Motion Sensor [18 m (60 ft)] with POPIT
X
PIR/Microwave Motion Sensor [+1.7?C (+35?F)] with
X
POPIT
1
Version 1.03 or above
4.3
Circuit Classes
Onboard Points
Onboard points, points 1 to 8, are Class B, Style B Initiating-Device Circuits.
Zonex Bus or Buses
Zonex buses are Class B, Style 4 Signaling Line Circuits.
Notification Appliance Circuit (NAC)
The control panels do not have an onboard NAC.
F.01U.167.105 | 02 | 2010.11
UL Installation Instructions
Bosch Security Systems, Inc.
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.com
© Bosch Security Systems, Inc., 2010