Bosch PLE-SDT Specifications

Communications Systems | PLE-SDT Plena Easy Line SD Tuner BGM source
PLE-SDT Plena Easy Line SD Tuner BGM
source
www.boschsecurity.com
The PLE-SDT Plena Easy Line SD Tuner BGM source is
the ideal high‑quality source for background music
(BGM) in public address systems. It provides hours of
uninterrupted music for professional systems. Designed without moving parts, it can be used in systems
that are on for long periods. It is designed to be used
with non-volatile steady state flash memory.
System Overview
The unit has a digital source side for MP3’s stored on
SD card and USB memory stick, and a side with an FM
tuner. It is typically used in hotels, shops, supermarkets, restaurants, bars, canteens, gyms, showrooms,
and other places where BGM creates the right atmosphere. It connects to any public address amplifier. The
design follows the Plena Easy Line design and is part
of the Advantage Line by Bosch.
Functions
Insert only one USB stick at the time.
If a USB stick is inserted in the front,
this socket cannot be used, and vice versa
ANTENNA
OUTPUTS
OUTPUT LEVEL
230V~50Hz 50W or 115V~60Hz 50W
TUNER
COMBINED
USB/SD
R
L
TUNER
R
L
COMBINED
R
L
USB/SD
USE ONLY WITH 250V FUSE
230V~FUSE T0.63A/250V or
115V~FUSE T1.25A/250V
With an SD/USB capacity of up to 32 GB (up to 2000
tracks) and the option to connect the USB either on
the front or rear panel, the digital player provides
hours of high‑quality, uninterrupted music playback
u
MP3 playback from SD card and USB inputs
u
FM tuner with RDS, presets and digital control
u
Simultaneous operation of SD/USB-player and FM
tuner
u
Separate outputs for digital source and FM tuner
from a single source. It supports music organized on a
disk in multiple folders. The player will automatically
search and play all playable MP3’s on a flash memory
device, and has repeat and random play modes.
Digital Source
It can play MP3’s with bit-rates from 32 kbps to
320 kbps, mono / stereo / joint‑stereo, and both constant bit-rates (CBR) and variable bit-rate (VBR) are
supported.
Tuner
The digitally controlled FM tuner uses a frequency synthesizer for accurate capture of radio stations and has
presets for FM to store favorite radio stations.
Outputs
Both the player and the tuner can operate simultaneously on different outputs. The output level of the outputs can be set via the rear panel. Next to the stereo
analog outputs per side, there is a combined output
that plays the digital content and automatically
switches over to the FM tuner when the last track has
been played.
2 | PLE-SDT Plena Easy Line SD Tuner BGM source
Certifications and Approvals
Total harmonic distortion (1 kHz)
< 0.8 %
Safety
according to IEC/EN 60065
FM range
87.5 ÷ 108 MHz
CCC
Frequency response
50 Hz ÷ 12 kHz
C‑Tick
Channel separation (1 kHz)
≥ 40 dB
EN 55013+A1+A2,
Intermediate rejection
≥ 70 dB
EN 61000‑3‑2,
Signal / noise ratio
≥ 50 dB
EN 61000‑3‑3+A1
Intermediate frequency
10.7 MHz
2006/95/CE LVD Directive
Input sensitivity
6 μV e.m.f. (2 uV)
2004/108/CE EMC
Automatic tuning sensitivity
≤ 50 μV
IEC EN 55020+A2+EC
Antenna input
75 ohms (coaxial)
CE marking
Audio output level
- 10 dBV
CE
Installation/Configuration Notes
SD / USB audio player
The PLE‑SDT is a 19” rack‑mount unit with detachable
rack mount brackets for tabletop use. The unit comes
with an IR remote control to control all sources. It is
compatible with High Capacity Secure Digital (SDHC),
MMC memory cards, Flash USB sticks and bus powered (2.5”) hard disk drives (HDD). System connection
cables are included.
Maximum storage capacity
32 GB
Maximum number of tracks
2000
Frequency response
50 Hz ÷ 20 kHz
Signal / noise ratio
≥ 70 dB
Total harmonic distortion (1 kHz)
< 0.1 %
Parts Included
Stereo separation
≥ 60 dB
Audio output level
- 10 dBV
Quantity
Components
1
PLE-SDT Plena Easy Line SD Tuner BGM source
1
AC Power cord
1
Safety instructions
1
Set of 19”mounting brackets
1
Mechanical
Dimensions (H x W x D)
44 x 444 x 250 mm
(1.73 x 17.48 x 9.84 in)
Mounting
Stand-alone, 19" rack
(19" wide, 1U high)
Remote control
Color
Charcoal with silver printing
2
2‑pair audio RCA cable (2.5 m)
Weight
Approx. 3.6 kg
1
SD card including free music and the instructions for use
Environmental
Technical Specifications
Operating temperature
-25 ºC to +45 ºC
Electrical
Storage temperature
-40 ºC to +70 ºC
Mains power supply
Relative humidity
< 90 % (non condensing)
Voltage
115 - 230 VAC ±10%,
50/60 Hz
Ordering Information
Power supply fuses
230 VAC 0.63 AT / 250 V
PLE-SDT Plena Easy Line SD Tuner BGM source
120 VAC 1.25 AT / 250 V
Order number PLE-SDT
Power consumtion (typical)
10 W
Power consumption (Max.)
50 VA
FM tuner
Distortion
<1%
USB/SD MP3 player and FM tuner functions.
Plena Easy Line SD Tuner BGM source
PLE-SDT
en
Installation and Operation manual
Plena Easy Line SD Tuner BGM source
Table of Contents | en
3
Table of Contents
1
Safety
5
2
Short Information
6
2.1
Purpose
6
2.2
Digital document
6
2.3
Intended audience
6
2.4
Alerts and notice signs
6
2.5
Conversion tables
7
3
System Overview
8
3.1
Application
8
3.2
Short description
8
3.3
Scope of delivery
8
3.4
The Plena Source Unit
8
3.5
Controls, connectors and indicators
9
3.5.1
Front view
3.5.2
Rear view
10
3.5.3
Remote control
11
4
Planning information
13
5
Installation
14
5.1
Source unit connections / settings
14
5.2
USB/SD
14
5.3
Remote control
14
6
Connections
15
6.1
Front side input sockets
15
6.1.1
USB
15
6.1.2
SD/MMC
15
6.2
Rear side input sockets
15
6.2.1
FM tuner antenna
15
6.2.2
USB
15
6.2.3
Mains power socket
16
6.3
Rear side audio output sockets
16
7
Configuration
17
7.1
FM tuner
17
7.1.1
Tuner audio output level control
17
7.1.2
Preset radio frequency programming
17
7.2
Combined audio output level control
18
7.3
USB/SD audio output level control
18
Bosch Security Systems B.V.
9
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
4
en | Table of Contents
Plena Easy Line SD Tuner BGM source
8
Operation
19
8.1
Remote control
19
8.2
USB/SD source
20
8.2.1
Replaying music tracks
20
8.2.2
Track selection
21
8.2.3
Repeat functions and random play
22
8.2.4
Making a playlist
22
8.2.5
Muting the output sound
23
8.3
FM tuner
24
8.3.1
Search a FM radio frequency
24
8.3.2
Preset FM radio frequency selection
24
8.3.3
Sequentially FM radio frequency preset selection
24
8.3.4
Manual selection of a FM radio frequency
25
8.3.5
Radio Data System (RDS)
25
8.3.6
Switch off timer
25
8.3.7
Stereo / mono output sound
26
8.3.8
Muting the output sound
26
9
Troubleshooting
27
10
Maintenance
29
10.1
Remote control
29
11
Technical Data
30
11.1
Electrical
30
11.1.1
Mains power supply
30
11.1.2
FM tuner
30
11.1.3
USB/SD source
30
11.2
Mechanical
31
11.3
Environmental
31
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
1
Safety | en
5
Safety
Prior to installing or operating this product, always read the Important Safety Instructions
which are available as a separate document (F.01U.120.759). These instructions are supplied
together with all equipment that can be connected to the mains supply.
Safety precautions
The PLE-SDT Plena Easy Line SD Tuner BGM source is designed to be connected to the 115/
230 Vac public distribution network.
To avoid any risk of electric shock, all interventions must be carried out with disconnected
mains supply.
Interventions with the equipment switched on are authorized only when it is impossible to
switch the equipment off. The operation must only be performed by qualified personnel.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
6
en | Short Information
Plena Easy Line SD Tuner BGM source
2
Short Information
2.1
Purpose
The purpose of this manual is to provide information required for installing, configuring,
operating and maintaining the PLE-SDT Plena Easy Line SD Tuner BGM source.
2.2
Digital document
This installation and operation manual is also available as a digital document in the Adobe
Portable Document Format (PDF).
Refer to the product related information on www.boschsecuritysystems.com.
Data and illustrations subject to change without notice.
2.3
Intended audience
These installation and operation instructions are intended for installers and users of a public
address system.
2.4
Alerts and notice signs
Four types of alerts can be used in this manual. The alert type is closely related to the effect
that may be caused if it is not observed. These alerts - from least severe effect to most severe
effect - are:
NOTICE!
Alert containing additional information. Usually, not observing a ‘notice’ does not result in
damage to the equipment or personal injuries.
CAUTION!
The equipment or the property can be damaged, or persons can be lightly injured if the alert is
not observed.
WARNING!
The equipment or the property can be seriously damaged, or persons can be severely injured
if the alert is not observed.
DANGER!
Not observing the alert can lead to severe injuries or death.
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
2.5
Short Information | en
7
Conversion tables
In this manual, SI units are used to express lengths, masses, temperatures etc. These can be
converted to non-metric units using the following information.
Imperial
Metric
Metric
Imperial
1 in =
25.4 mm
1 mm =
0.03937 in
1 in =
2.54 cm
1 cm =
0.3937 in
1 ft =
0.3048 m
1m=
3.281 ft
1 mi =
1.609 km
1 km
0.622 mi
Table 2.1 Conversion of units of length
Imperial
Metric
Metric
Imperial
1 lb =
0.4536 kg
1 kg =
2.2046 lb
Table 2.2 Conversion of units of mass
Imperial
Metric
Metric
Imperial
1 psi =
68.95 hPa
1 hPa =
0.0145 psi
Table 2.3 Conversion of units of pressure
NOTICE!
1 hPa = 1mbar.
Fahrenheit
Celsius
°F = 9/5 (°C + 32)
°C = 5/9 (°F - 32)
Table 2.4 Conversion of units of temperature
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
8
en | System Overview
Plena Easy Line SD Tuner BGM source
3
System Overview
3.1
Application
The PLE-SDT Plena Easy Line Source Unit is the ideal high-quality source for music in public
address systems. It provides hours of uninterrupted music for professional systems. Designed
without moving parts, it can be used in systems that are on for long periods of time. It is
designed to be used with non-volatile steady state flash memory.
3.2
Short description
The Plena Easy Line Source Unit is divided in a USB/SD source part, for playing MP3’s stored
on USB flash memory device and SD/MMC card, and a FM tuner part. The source unit is
typically used in hotels, shops, supermarkets, restaurants, bars, canteens, gyms, showrooms,
and other places where background music (BGM) creates the right atmosphere. It connects to
any public address amplifier. The design follows the Plena Easy Line design and is part of the
Advantage Line by Bosch.
3.3
Scope of delivery
The PLE-SDT Plena Source Unit is packed with the following parts:
–
3.4
1x Mains power cord
–
1x Safety instructions
–
1x Set of 19”mounting brackets (mounted)
–
1x Remote control (Not included: 2x 1.5V, size AAA battery)
–
2x 2-pair audio RCA cable (2.0 m)
–
1x Antenna cord including connector
–
1x SD memory card including free music and this installation and operation manual
The Plena Source Unit
With an USB or SD card memory capacity of up to 32 GB (up to 2000 tracks), and the option
to connect the USB flash memory device either on the front or rear side, the USB/SD source
provides hours of high-quality, uninterrupted music playback from a single source. It supports
MP3 music files organized in multiple folders. The USB/SD source will automatically search
and play all playable MP3’s on a flash memory device, and has repeat and random play modes.
USB/SD source
The USB/SD source can play MP3’s with bit-rates from 32 kbps to 320 kbps, mono / stereo /
joint-stereo, and both constant bit-rate (CBR) and variable bit-rate (VBR) are supported.
FM tuner
The digitally controlled FM tuner uses a frequency synthesizer for accurate capture of FM
radio frequencies and has 30 presets to store your favorite radio stations.
Outputs
The USB/SD source and the FM tuner can operate simultaneously on different outputs. The
audio output level of the outputs can be set with the controls on the rear side. Next to the
stereo analog outputs for the USB/SD source and FM tuner, there is a combined output that
plays the USB/SD source content and automatically switches over to the FM tuner when the
last MP3 track has been played.
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
System Overview | en
3.5
Controls, connectors and indicators
3.5.1
Front view
9
Figure 3.1 Front view
Number Front view
Description
1
Mains power switch (On/Off).
Refer to Section 5.1 Source unit connections / settings.
2
USB 2.0 4-pin socket. Refer to Section 6 Connections.
3
-
LCD (with backlight) for USB device or SD card operation.
A
-
Keypad for USB device or SD card operation. Refer to Section 8 Operation.
4
To mute the audio output level of USB or SD source.
Refer to Section 8.2.5 Muting the output sound.
6
|< - SKIP - >|
Track selection and fast forward/reverse.
Refer to Section 8.2.2 Track selection.
7
|<< FOLDER >>|
8
9
File selection. Refer to Section Selection of folders and search for folders, page 22.
To stop the track replay.
PROG
To switch to the programming mode to compile an individual MP3 track sequence.
Refer to Section 8.2.4 Making a playlist.
10
>||
11
To switch between track replay and pause.
To select the repeat and random replay functions.
Refer to Section 8.2.3 Repeat functions and random play.
12
USB/SD
On/Off USB/SD source LED indicator.
Refer to Section 8.1 Remote control.
13
USB
To select USB device operation.
Refer to Section 8.2 USB/SD source.
14
SD
To select SD card operation.
Refer to Section 8.2 USB/SD source.
15
SD/MMC
SD card socket.
16
-
LCD (with backlight) for FM tuner operation.
B
-
Keypad for FM tuner operation.
Refer to Section 8.2 USB/SD source.
Refer to Section 7.1 FM tuner and Section 8.3 FM tuner.
17
1-9, 10/0
Radio frequency (preset) selection.
Refer to Section 8.3 FM tuner.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
10
en | System Overview
Number Front view
18
Plena Easy Line SD Tuner BGM source
Description
-
IR receiver lens (remote control).
Refer to Section 8.1 Remote control.
19
|<
Every time you press the button the tuning frequency goes down with 50 kHz. Press
for two seconds to scan down to the next station.
Refer to Section 8.3 FM tuner.
20
+10
Radio frequency preset selection (>10).
Refer to Section 8.3 FM tuner.
21
TUNER
On/Off LED indicator FM tuner.
Refer to Section 8.1 Remote control.
22
>|
Every time you press the button the tuning frequency goes up with 50 kHz. Press for
two seconds to scan up to the next station.
Refer to Section 8.3 FM tuner.
23
PROG
To save the radio frequency presets.
Refer to Section 7.1.2 Preset radio frequency programming.
3.5.2
Rear view
Figure 3.2 Rear view
Number Rear view
Description
24
FM tuner antenna input (75 Ohm) socket.
ANTENNA
Refer to Section 6.2.1 FM tuner antenna.
25
26
USB 2.0 4-pin socket. Refer to Section 6 Connections.
TUNER
Tuner audio output level control.
Refer to Section 7.1.1 Tuner audio output level control.
27
COMBINED
Combined USB/SD and FM tuner audio output level control. Refer to
Section 7 Configuration.
28
USB/SD
USB/SD audio output level control.
Refer to Section 7.1.1 Tuner audio output level control.
29
TUNER R/L
Tuner output (right and left channel) sockets.
Refer to Section 6.3 Rear side audio output sockets.
30
COMBINED R/L
Combined USB/SD and FM tuner output (right and left channel) sockets.
Refer to Section 6.3 Rear side audio output sockets.
31
USB/SD R/L
USB/SD output (right and left channel) sockets.
Refer to Section 6.3 Rear side audio output sockets.
33
-
Mains power inlet + fuse holder.
(Fuse: 230V = 0.63AT/250V. Fuse: 115V = 1.25AT/250V).
Refer to Section 6.2.3 Mains power socket.
34
-
Mains power selector (230V or 115V).
Refer to Section 5.1 Source unit connections / settings.
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
3.5.3
System Overview | en
11
Remote control
Figure 3.3 Remote control (The numbers of the remote control and in the table, are identical to the numbers of the unit.)
Number Function Button
Description
17 / 20
Radio frequency preset selection or track selection.
TUNER,
1-9, 10/0, +10
USB/SD
36
TUNER
Refer to Section 8.3 FM tuner or Section 8.2.2 Track selection.
FREQ
Manual selection of FM radio frequency.
Refer to Section 8.3.4 Manual selection of a FM radio frequency.
42
TUNER
|<< PRESET >>|
Scroll up/down radio frequency presets.
Refer to Section 8.3 FM tuner.
7
USB/SD
|<< FOLDER >>|
Scroll up/down MP3 folder selection.
Refer to Section Selection of folders and search for folders, page 22.
9
USB/SD
PROG
To switch to the programming mode to compile an individual track
sequence.
Refer to Section 8.2.4 Making a playlist.
23
TUNER
PROG
To save the selected radio frequency to a preset.
Refer to Section 7.1.2 Preset radio frequency programming.
11
USB/SD
To select the repeat and random replay functions.
Refer to Section 8.2.3 Repeat functions and random play.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
12
en | System Overview
Plena Easy Line SD Tuner BGM source
Number Function Button
Description
39
To select USB/SD or FM tuner operation.
USB/SD,
USB/SD-TUNER
TUNER
40
TUNER
Refer to Section 8.1 Remote control.
SLEEP
To set the FM tuner switch-off timer.
Refer to Section 8.3.6 Switch off timer.
35
TUNER
RDS
Radio Data System. To display FM radio frequency information.
Refer to Section 8.3.5 Radio Data System (RDS).
43
TUNER
SEARCH
To search for a radio frequency.
Refer to Section 8.3.1 Search a FM radio frequency.
37
TUNER
ST/MONO
To switch between stereo or mono audio output signal.
Refer to Section 8.3.7 Stereo / mono output sound.
19, 22
TUNER
|< - TUNE - >|
Every time you press one of the buttons the tuning frequency goes up or
down with 50 kHz. Press for two seconds to scan up to the next station.
Refer to Section 8.3 FM tuner.
6
USB/SD
|< - SKIP - >|
For track selection and fast forward/reverse.
Refer to Section 8.2.2 Track selection.
10
USB/SD
>||
To switch between track replay and pause.
Refer to Section 8.2 USB/SD source.
8
USB/SD
To stop the track replay. Refer to Section 8.2 USB/SD source.
4
USB/SD,
To mute the audio output level of USB / SD source or FM Tuner.
TUNER
Refer to Section 8.2.5 Muting the output sound of the USB/SD.
Refer to Section 8.3.8 Muting the output sound of the FM Tuner.
13, 14
USB/SD
USB-SD
To select USB device or SD card operation.
Refer to Section 8.2 USB/SD source.
41
USB/SD,
-
IR transmitter lens. Refer to Section 8.1 Remote control.
TUNER
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
4
Planning information | en
13
Planning information
Make sure that:
–
No liquids can spill into or on the unit.
–
The ventilation airflow is not obstructed.
–
There is a mains power outlet of sufficient rating close to the intended location.
And:
–
Bosch Security Systems B.V.
Leave at least 10 cm of free space at the rear of the unit for connectors and wiring.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
14
5
en | Installation
Plena Easy Line SD Tuner BGM source
Installation
The PLE-SDT Plena Easy Line SD Tuner BGM source is designed for installation into a 19"
rack; however, it can also be used as a desktop unit. For 19" rack installation; use the 19" rack
mounting brackets which come with the source unit.
Figure 5.1 Set of 19" rack mounting brackets
5.1
Source unit connections / settings
1.
Connect any additional equipment/wires. Refer to Section 6 Connections.
2.
Check/set the configuration settings. Refer to Section 7 Configuration.
CAUTION!
1.
2.
Set the mains power switch (1) on the unit’s front side to the Off position.
Make sure that the mains power selector (34) on the unit’s rear side is correctly set for
the local mains voltage.
3.
Change the mains fuse into T1.25A/250V, when connected to 115 V mains voltage.
4.
Insert the power cord in the mains power inlet (33) and connect it into the distribution
network mains outlet.
5.2
USB/SD
Connect a USB flash memory device to the USB socket (2 or 25). The use of USB HDD is not
recommended. And/or insert an SD/MMC memory card into the socket SD/MMC (15), the
notched corner of the card facing up as indicated on the unit’s front panel.
5.3
Remote control
To insert the batteries (2x 1,5V, size AAA):
1.
Remove the battery compartment cover on the rear side of the remote control.
2.
Insert the batteries as indicated in the battery compartment.
3.
Close the battery compartment with the cover.
NOTICE!
If the remote control is not in use for a longer period of time, remove the batteries to prevent
any damage due to battery leakage.
NOTICE!
Disposable batteries and battery packs at the end of their technical lives should be discarded
with due care for the environment. When possible, take batteries to a local recycling station.
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
6
Connections | en
15
Connections
Figure 6.1 Front view
Figure 6.2 Rear view
6.1
Front side input sockets
6.1.1
USB
Connect a USB flash memory device (maximum 32 GB), with MP3 file format stored, to the
USB 2.0 4-pin socket (2). Refer to Section 8.2 USB/SD source.
NOTICE!
Connect only one USB flash memory device at the time. If a USB flash memory device is
connected to the rear (25), the USB front socket (2) cannot be used.
6.1.2
SD/MMC
Insert a SD/MMC memory card (maximum 32 GB), with MP3 file format stored, to the SD/
MMC card socket (15). Refer to Section 8.2 USB/SD source.
6.2
Rear side input sockets
6.2.1
FM tuner antenna
The FM tuner antenna socket (24) must be connected to an antenna or cable network with a
COAX cable of 75 Ohm. A antenna cord with connector comes with the unit.
6.2.2
USB
Connect a USB flash memory device (maximum 32 GB), with MP3 file format stored, to the
USB 2.0 4-pin socket (25). Refer to Section 8.2 USB/SD source.
NOTICE!
Connect only one USB flash memory device at the time. If a USB flash memory device is
connected to the front (2), the USB rear socket (25) cannot be used.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
16
en | Connections
6.2.3
Plena Easy Line SD Tuner BGM source
Mains power socket
CAUTION!
Before applying mains power, the first time, check the mains power selector (34) and the
correct fuse value (33) on the unit’s rear side.
Insert the power cord connector to the mains power inlet (33) and plug it into the distribution
network mains outlet socket.
Important for U.K. customers
The wires of the supplied mains lead are colored in accordance with the following code:
–
Green/yellow = earth
–
Blue = neutral
–
Brown = live
As the colors of the wires in the mains lead of this appliance may not correspond with the
colored markings identifying the terminals in your plug, proceed as follows:
1.
The wire which is colored green and yellow must be connected to the terminal in the plug
which is marked with the letter E or by the earth symbol, or colored green or green and
yellow.
2.
The wire which is colored blue must be connected to the terminal which is marked with
the letter N or colored black.
3.
The wire which is colored brown must be connected to the terminal which is marked with
the letter L or colored red.
6.3
Rear side audio output sockets
The USB/SD source and the FM tuner can operate simultaneously on different outputs:
1.
Connect the outputs (R = Right channel, L = Left channel) of the source USB/SD (31) and
TUNER (29) via cables, with RCA connectors, to the inputs, e.g. on a audio mixer /
amplifier.
Next to the stereo analog outputs for the USB/SD and FM tuner, there is a COMBINED (30)
output that plays the USB/SD content and automatically switches over to the FM tuner when
the last MP3 track has been played:
1.
Connect the outputs (R = Right channel, L = Left channel) via a cable with RCA
connectors to the inputs, e.g. on a audio mixer / amplifier.
The audio output level of the three outputs can be set with the controls (26, 27 and 28) on the
rear side of the source unit.
1.
PLE-SDT_OM | V1.0 | 2012.02
Refer to section Section 7 Configuration.
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
7
Configuration | en
17
Configuration
Switch on the unit with the POWER switch (1).
Figure 7.1 Front view
Figure 7.2 Rear view
7.1
FM tuner
7.1.1
Tuner audio output level control
1.
2.
7.1.2
Set the TUNER (26) audio output level control to the required amplifier input level.
–
The audio output level could be set between mute and 1.5 Vrms.
–
It is advised to set the control in the upper mid position, at start.
Refer to Section 11 Technical Data for audio output level.
Preset radio frequency programming
1.
Select the FM tuner source with the remote control button USB/SD/-TUNER (39).
–
The green LED TUNER (21) will light up.
2.
Select the required FM radio frequency with the buttons |< (19) and >| (22).
3.
Press the button PROG (23).
–
The FM tuner LCD (16) shows the preset number (CHxx) flashing during this
process.
–
Maximum 30 presets could be stored.
4.
Press a button 1 to 10/0 (17) for preset position 1 to 10. Or:
5.
Press the button 1 to 10/0 (17) following by the button +10 (20) for preset positions 11
to 30.
–
1st actuation of button +10: Preset 11 up to 19.
–
2nd actuation of button +10: Preset 20 up to 30.
6.
Press the button PROG (23) again to store the selected FM radio frequency as a preset.
7.
Refer to Section 8.3.2 Preset FM radio frequency selection.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
18
7.2
en | Configuration
Plena Easy Line SD Tuner BGM source
Combined audio output level control
The COMBINED (30) output plays the USB/SD content and automatically switches over to the
FM tuner when the last MP3 track has been played:
1.
2.
7.3
Set the COMBINED (27) audio output level control to the required amplifier input level.
–
The audio output level could be set between mute and 1.5 Vrms.
–
It is advised is to set the control in the upper mid position, at start.
Refer to Section 11 Technical Data for output level.
USB/SD audio output level control
1.
2.
PLE-SDT_OM | V1.0 | 2012.02
Set the USB/SD (28) audio output level control to the required amplifier input level:
–
The audio output level could be set between mute and 1.5 Vrms.
–
It is advised is to set the control in the upper mid position, at start.
Refer to Section 11 Technical Data for output level.
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
8
Operation | en
19
Operation
Switch on the source unit with the POWER switch (1). The USB/SD LCD (3) will show
“Version x.x” and the FM tuner LCD (16) will show the last used FM radio frequency and or
preset radio frequency. First the USB/SD source will read the USB flash memory on the front
(2) and rear (25). If no USB flash memory device has been connected, the USB/SD source
LCD (3) will show “NO USB" and it will continue to read the SD/MMC (15) memory. If no SD
memory card has been inserted, the USB/SD source LCD will show “NO CARD”.
NOTICE!
The unit will play FAT32 formatted SDHC card and USB sticks. Some rare occurring partition
tables will not be played despite FAT32 formatting. Most standard available USB flash memory
and SD card will be played. If a card is not played, please check with a different type of card
whether the unit is faulty or whether a non compliant format is used.
8.1
Remote control
When you press a button on the remote control, always direct the remote control IR
transmitter lens (41) towards the IR receiver lens (18) of the source unit. There must be no
obstacles between the remote control and the IR receiver lens.
The button functions of the remote control are identical to the buttons on the source unit
front side. Refer to Section 3.5.3 Remote control and the following sections.
Figure 8.1 Remote control
1.
First select the source to be controlled by the remote control with the button USB/SD/TUNER (39):
–
2.
The green LED USB/SD (12) or TUNER (21) will light up of the selected unit source.
Continue with Section 8.2 USB/SD source or with Section 8.3 FM tuner.
NOTICE!
If the range of the remote control decreases, the batteries are exhausted and must be
replaced. Refer to Section 5.3 Remote control.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
20
en | Operation
8.2
Plena Easy Line SD Tuner BGM source
USB/SD source
The USB/SD source support MP3 audio file format, stored on a USB flash memory device
(FAT32) and SD memory card.
1.
Be sure that an USB flash memory device is connected to the USB socket (2 or 25) and or
an SD memory card is inserted into the socket SD/MMC (15).
2.
Press the button USB/SD-TUNER (39) of the remote control to select and operate the
USB/SD source, if required.
–
The green LED USB/SD (12) will light up.
Figure 8.2 USB/SD source front view
NOTICE!
For configuration settings, refer to Section 7.3 USB/SD audio output level control.
8.2.1
Replaying music tracks
1.
Select the source (USB device or SD/MMC) with the button USB (13) or SD (14), if
necessary:
–
After USB device or SD/MMC reading, the lower line of the LCD (3) will show the
number of folders (left hand side) and the number of tracks (right hand side). The
LCD (3) upper line (left corner) will show the selected source "USB" or "CARD".
2.
Start replay the first track with the button >|| (10). To select another track, refer to
section Section 8.2.2 Track selection.
–
The following additional information will scroll in the LCD upper line:
File – < name >, Track – < name >, Artist – < name >, Album – < name >
Remark: If an information is not available, the LCD will show “NONE” instead of a name.
–
The LCD lower line will show from left to right:
TRxxxx (track number (maximum 2000 tracks)), mm:ss (track playing time), MP3
(audio file format).
3.
Press the button >|| (10) to switch between replay and pause:
–
In the pause mode, the pause symbol (||) will be shown in the upper line and the
time indication will flash in the LCD.
–
4.
In the replay mode, the replay symbol (>) will be shown in the upper line of the LCD.
To stop the replay, press the button
–
(8):
The lower line of the LCD (3) will default show the number of folders (left hand
side) and the number of tracks (right hand side).
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
8.2.2
Operation | en
21
Track selection
The following track selections could be made:
–
Section Manual selection of the track number, page 21
–
Section Skipping tracks in forward/reverse direction, page 21
–
Section Fast forward/reverse, page 21
–
Section Selection of folders and search for folders, page 22
Manual selection of the track number
1.
Select the source (USB device or SD/MMC card) with the button USB (13) or SD (14), if
necessary.
2.
Enter the track number with the numerical buttons (17, 20) on the remote control.
3.
Press the button >|| (10), to replay the track.
Examples:
Track number
Press the buttons
4
4 + >||
27
2 + 7 + >||
135
1 + 3 + 5 + >||
NOTICE!
The player will arrange the tracks as follows:
1. All tracks without folder in the ROOT directory.
2. All tracks with folders in the ROOT directory.
3. All tracks in sub folders, etc.
The tracks and folders will not be arranged in alphabetical order.
Skipping tracks in forward/reverse direction
1.
Select the source (USB device or SD/MMC card) with the button USB (13) or SD (14), if
necessary.
2.
To skip one track or several tracks in forward or reverse direction, press the skip button
|< or >| (6) repeatedly:
–
Button >|: To skip to the next track.
–
Button |<: To return to the beginning of the track currently playing.
–
Each time the button |< is pressed again, the unit will go back one track at a time.
Fast forward/reverse
1.
Select the source (USB device or SD/MMC card) with the button USB (13) or SD (14), if
necessary.
2.
For fast forward, keep the button >| (6) pressed.
3.
For fast reverse, keep the button |< (6) pressed.
NOTICE!
With MP3 files, fast forward/reverse will only be possible within a track. You will be able to
trace it by means of the time indication on the LCD (3), not acoustically.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
22
en | Operation
Plena Easy Line SD Tuner BGM source
Selection of folders and search for folders
1.
Select the source (USB device or SD/MMC card) with the button USB (13) or SD (14), if
necessary.
2.
With files in several folders (file directories), press the button FOLDER (7) during the
replay to go to the first track of the next folder (>>|) or to the first track of the previous
folder (|<<).
3.
If you stop the replay with the button
(8) first and then press the button FOLDER |<<
or >>|:
–
The upper line of the LCD (3) will show the folder name and the lower line will show
the folder number behind the directory symbol.
8.2.3
Repeat functions and random play
1.
Select the source (USB device or SD/MMC card) with the button USB (13) or SD (14), if
necessary.
2.
Press the button
(11) to activate one of the repeat functions and the replay of the
tracks in random order:
–
Basic setting (PLAY ALL): All tracks of the sound carrier or of a programmed track
sequence will be replayed once, then the replay will stop.
–
1st actuation of button (PLAY ALL RANDOM): The tracks will be replayed once in
random order.
–
2nd actuation of button (REPEAT TRACK): The track selected will be repeated
continuously.
–
3th actuation of button (REPEAT FOLDER): All tracks in the folder selected will be
repeated continuously.
–
4th actuation of button (REPEAT ALL): All tracks will be repeated continuously.
–
5th actuation of button (RANDOM REPEAT): All tracks will be replayed continuously
in random order.
–
6th actuation of button (PLAY ALL): Return to basic setting.
NOTICE!
At random play, the LCD (3) upper line will show RDM (left hand side) including the selected
random function symbol (right hand side). At repeat play, the LCD upper line will show the
selected repeat function symbol (right hand side).
8.2.4
Making a playlist
For replaying a selection of tracks in a certain order, a sequence (playlist) of up to 64 tracks
can be programmed. For this purpose the arrangement of the folders should be known to you.
Refer to the previous Section Selection of folders and search for folders, as it will be necessary
to enter the corresponding number of each track to be programmed.
1.
Select the source (USB device or SD/MMC card) with the button USB (13) or SD (14), if
necessary.
2.
3.
Stop the playing track by pressing the button
(8).
Activate the programming mode with the button PROG (9).
–
Press all other buttons within 15 seconds otherwise you will exit the programming
mode. In this case press the button PROG once again.
–
The LCD (3) will show: "PROGRAM" in the upper line and "P-01 000 0000" in the
lower line.
4.
Select the number of the folder (xxx) containing the first track desired for the track
sequence with the buttons |< – SKIP – >| (6) or enter it with the remote control numerical
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
Operation | en
23
keys (17, 20) (This is also necessary when all the files are in the ROOT directory without
folder).
–
5.
–
6.
In this example, enter 1 as the folder number.
To memorize press the button PROG (9):
The LCD (3) will show the track number (xxxx) flashing.
Select the number of the first track (xxxx) of the track sequence with the buttons |< –
SKIP – >| (6) or enter it with the remote control numerical keys (17, 20).
–
For MP3 files in folders, please note that these files are not arranged consecutively
but that the first file in each folder is always number 1.
7.
To memorize press the button PROG (9):
–
8.
The LCD (3) will show the next memory location number, e.g. “P–02”.
Repeat the steps 3 up to 7 for all further tracks desired until the entire track sequence
has been programmed.
9.
To start the track sequence, press the button >|| (10):
–
The upper line of the LCD will show “MEM” (memory) and the track sequence will
be replayed.
10. Press the buttons |< – SKIP – >| (6) to select any track of the track sequence or keep the
corresponding button pressed to activate the fast forward/reverse function within a
track.
11. The replay will stop after the track sequence has been replayed or when you press the
button
(8).
12. To restart the track sequence, first press the button
(8), then press the button
PROG (9) and then the button >|| (10).
A track sequence will be not stored when:
8.2.5
–
you change from source (USB / SD / TUNER).
–
you press the button
–
you switch off the source unit (button 1).
(8) in the programming mode.
Muting the output sound
To mute the audio output sound (outputs: 30, 31) of the track during replay:
1.
Press the button
–
(4):
The LCD lower line will show MUTE flashing continuously when the mute function is
activated.
2.
To reactivate the sound, press the button
–
Bosch Security Systems B.V.
(4) once again:
The LCD (3) upper line will show "MUTE OFF" for 3 seconds.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
24
en | Operation
8.3
Plena Easy Line SD Tuner BGM source
FM tuner
1.
Press the button USB/SD-TUNER (39) of the remote control to select and operate the FM
tuner.
–
The green LED TUNER (21) will light up.
Figure 8.3 FM tuner front view
8.3.1
Search a FM radio frequency
Use the buttons TUNE |< (19) or >| (22) to search for a FM radio frequency:
1.
2.
Press the button |< or >| once to fine tune. Or,
Press and hold (± 1 second) the button |< or >| to search for (strong) FM radio
frequencies automatically. Or,
Use the button SEARCH (43) of the remote control to search for a (strong) FM radio
frequency automatically:
1.
8.3.2
Press the button SEARCH for approx. 2 seconds to start the searching.
Preset FM radio frequency selection
Stored FM radio frequency presets (maximum 30) are selected by pressing:
1.
The button 1 to 10/0 (17) for presets 1 to 10. Or,
2.
The button 1 to 10/0 (17) following by the button +10 (20) for preset positions 11 to 30:
–
1st actuation of button +10: Preset 11 up to 19.
–
2nd actuation of button +10: Preset 20 up to 30.
NOTICE!
For FM tuner preset programming, refer to Section 7.1 FM tuner.
8.3.3
Sequentially FM radio frequency preset selection
1.
Press the buttons |<< PRESET >>| (42) of the remote control to scroll up/down between
the stored presets.
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
8.3.4
Operation | en
25
Manual selection of a FM radio frequency
1.
Press the button FREQ (36) of the remote control, followed by its 4 or 5 number FM
radio frequency digit, with the numerical buttons (17).
–
The FM radio frequency is set/activated after about two seconds.
–
The FM radio frequency range can be set between: 87.50 MHz and 108.00 MHz.
Examples:
FM frequency
Press the buttons
87.50 MHz
FREQ + 8 + 7 + 5 + 0
108.00 MHz
FREQ + 1 + 0 + 8 + 0 + 0
NOTICE!
Entering a non existing FM radio frequency will result in the LCD message: ERROR, result in a
time out and return to the default radio frequency screen.
8.3.5
Radio Data System (RDS)
The Radio Data System button RDS (35) of the remote control is used to display FM radio
frequency information, if it is broadcasted (for example; the time, radio station and or
programme information):
1.
Select the FM tuner source with the remote control button USB/SD/-TUNER (39).
–
2.
The green LED TUNER (12) will light up.
Press the button RDS (35).
–
The lower line of the LCD (16) will show the FM radio frequency broadcast
information, If available.
3.
8.3.6
Press the button RDS (35) again to switch off the RDS function, if required.
Switch off timer
1.
Press the button SLEEP (40) of the remote control to automatically switch off the FM
tuner by the build-in timer function. The LCD (16) upper line shows "SLEEP" if the switch
off timer is set between 90-10 minutes.
The switch off timer can be set between: Off, 90-10 minutes:
2.
–
Basic setting: Switch off timer off.
–
1st actuation of button: Sets the switch off timer to 90 minutes.
–
2nd actuation of button: Sets the switch off timer to 80 minutes.
–
3th actuation of button: Sets the switch off timer to 70 minutes.
–
4th actuation of button: Sets the switch off timer to 60 minutes.
–
5th actuation of button: Sets the switch off timer to 50 minutes.
–
6th actuation of button: Sets the switch off timer to 40 minutes.
–
7th actuation of button: Sets the switch off timer to 30 minutes.
–
8th actuation of button: Sets the switch off timer to 20 minutes.
–
9th actuation of button: Sets the switch off timer to 10 minutes.
–
10th actuation of button: Return to basic setting.
To change the switch off setting, press the button SLEEP (40) of the remote control
again.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
26
en | Operation
8.3.7
Plena Easy Line SD Tuner BGM source
Stereo / mono output sound
To switch between stereo and mono audio output sound (output 29) of the FM tuner:
1.
Press the button ST/MONO (37) of the remote control:
–
The LCD (16) upper line will show "STEREO" when stereo is set or "MONO" when
mono is set.
2.
Press the button ST/MONO (37) again to switch between mono and stereo.
NOTICE!
Sometimes a stereo FM radio frequency produce unwanted output noise. In that case, get a
good public antenna connection or set the FM tuner in the mono mode.
8.3.8
Muting the output sound
To mute the audio output sound (output: 29) of the FM tuner:
1.
Press the button
–
(4) of the remote control:
The LCD lower line will show MUTE flashing continuously when the mute function is
activated.
2.
PLE-SDT_OM | V1.0 | 2012.02
To reactivate the sound, press the button
Installation and Operation manual
(4) once again.
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
9
Troubleshooting | en
27
Troubleshooting
Problem
Possible cause
The unit does not work.
Power (plug) disconnected, the Insert power cord and switch on
Possible solution
unit is switched off or the mains the unit. Check the mains fuse.
fuse is broken.
Device does not comply with
Use a device complying with
USB mass storage.
USB mass storage class (some
portable audio players included
in the class of image devices are
not supported. Also, some flash
card readers cannot be
detected)
USB hub in use.
Some USB hubs will not operate
properly. Try a different USB
hub, or connect the storage
device directly to the USB port.
Also, if multiple USB storage
devices are connected through a
USB hub, only one of the devices
USB/SD storage device
not detected.
will be recognized.
Format not supported.
Use only FAT32 format.
The connection with the unit has Wait several minutes. The rating
been terminated because an
(allowable current) for this unit
electrical current stronger than
is 500 mA or less per USB port.
allowable was applied to the
Use USB storage devices that
unit’s USB1 or USB2 port.
meet these standards. If you
have a USB storage device
connected through a buspowered USB hub, connect the
USB storage device directly to
this unit port.If shorted a long
time the USB port will become
defective.
Partitioning of SD card is wrong. Reformat the USB or SD card
Apart from SD, SDHC and class
with a PC that has been known
of SD cards, it is also possible
to give good results.
that the card has a different
partition table then expected.
Format not supported.
Refer to section 3.4 on
supported formats. Basically
Can’t play MP3 or AAC
MP3’s are supported up to 320
tracks
kbps.
Files are copy-protected.
Bosch Security Systems B.V.
Installation and Operation manual
Cannot be used on this unit.
PLE-SDT_OM | V1.0 | 2012.02
28
en | Troubleshooting
Plena Easy Line SD Tuner BGM source
Problem
Possible cause
Possible solution
The audio output cable has
Plug in audio cable properly.
come loose or has not been
properly plugged in.
No audio output sound.
The audio output control is not
Check the output control setting
working properly.
on the rear panel.
The audio output connectors or Wipe away dust or dirt and
plugs are dirty.
reinsert the plug.
The selected source is currently Press the play/mute button.
in the pause or mute mode.
The audio output cable has not
Connect the audio cable to the
The audio output sound is been properly plugged i.n
line input of the amplifier.
distorted or full of noise. Connectors or plugs are dirty.
Wipe away dust or dirt and
reinsert the plug.
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
10
Maintenance | en
29
Maintenance
The PLE-SDT Plena Easy Line SD Tuner BGM source has been designed to function without
problems for a long period of time with a minimum of maintenance.
In order to guarantee trouble-free operation:
–
Clean the unit with a damp lint free cloth; never use water or chemicals.
–
Base the interval on the actual situation and dust build up, start with an interval of at
least once a year.
–
Periodically check the connectors for corrosion and the screw terminals to make sure
that they have not become loosened.
10.1
Remote control
If the range of the remote control decreases, the batteries are exhausted and must be
replaced (2x 1,5V, size AAA). Refer to Section 5.3 Remote control.
NOTICE!
If the remote control is not in use for a longer period of time, remove the batteries to prevent
any damage due to battery leakage.
NOTICE!
Disposable batteries and battery packs at the end of their technical lives should be discarded
with due care for the environment. When possible, take batteries to a local recycling station.
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02
30
en | Technical Data
Plena Easy Line SD Tuner BGM source
11
Technical Data
11.1
Electrical
11.1.1
Mains power supply
Voltage:
115 - 230 VAC, ±10%, 50/60 Hz
Power supply fuses:
230 Vac = 0.63 AT / 250 V
115 Vac = 1.25 AT / 250 V
Power consumption:
11.1.2
- Typical
10 W
- Maximum
50 VA
FM tuner
The output performance * is valid for the TUNER and COMBINED output.
11.1.3
Distortion *:
<1%
Total harmonic distortion (1 kHz) *:
< 0.8 %
FM frequency range:
87.5 MHz - 108 MHz
Frequency response:
50 Hz - 12 kHz
Channel separation (1 kHz) *:
≥ 40 dB
Intermediate rejection *:
≥ 70 dB
Signal / noise ratio *:
≥ 50 dB
Intermediate frequency *:
10.7 MHz
FM Input sensitivity:
6 μV e.m.f. (2 μV)
Automatic tuning sensitivity:
≤ 50 μV
Antenna input:
75 ohms (coaxial)
Audio output level *:
1.5 Vrms +/- 1 dB
USB/SD source
Frequency response:
50 Hz - 20 kHz
Signal / noise ratio:
≥ 70 dB
Total harmonic distortion (1 kHz):
< 0.1 %
Stereo separation:
≥ 60 dB
Audio output level:
1.5 Vrms +/- 1 dB
Maximum USB current:
500 mA
Maximum USB or SD card size:
32 GB
Supported USB or SD MMC:
FAT32 (32 bit File Allocation Table) or SD, SDHC
PLE-SDT_OM | V1.0 | 2012.02
Installation and Operation manual
Bosch Security Systems B.V.
Plena Easy Line SD Tuner BGM source
11.2
Technical Data | en
31
Mechanical
Unit dimensions (H x W x D):
- With brackets:
44 x 482 x 250 mm (1.73 x 18.97 x 9.84 in)
- Without brackets:
42 x 430 x 250 mm (1.65 x 16.93 x 9.84 in)
Unit mounting:
Stand-alone, 19" rack (19" wide, 1U high)
Unit color:
Charcoal with silver printing
Unit weight:
Approx. 3.6 kg
Remote control dimensions
(H x W x D):
20 x 52 x 156 mm (0.80 x 2.05 x 6.14 in)
Remote control color:
Charcoal with silver printing
Remote control weight:
120 g
(without batteries)
11.3
Environmental
Operating temperature:
0 °C to +45 °C
Storage temperature:
-40 °C to +70 °C
Relative humidity:
< 90 % (non condensing)
Bosch Security Systems B.V.
Installation and Operation manual
PLE-SDT_OM | V1.0 | 2012.02