White Z-200 User manual
Add to my manuals9 Pages
White Z-200
Below you will find brief product information for White Z-200. This high-power LED fixture features a 200W COB LED, a 15º to 28º zoom, and a variety of control options, making it ideal for a wide range of applications.
The White Z-200 can be controlled via DMX or standalone mode. In DMX mode, it offers two operating modes: a 2-channel mode with dimmer and zoom control and a 3-channel mode with dimmer, zoom, and strobe control. In standalone mode, the fixture can be set to one of three built-in programs or controlled via the digital display on the fixture base.
The White Z-200 is also equipped with a number of features that make it easy to use and maintain. These features include:
advertisement
USER MANUAL
Table of Contents
Safety Information………………………………………………………………3
Specifications…………………………………………………………………...4
Main Power Connection………………………………………………………..5
DMX-512 Connection…………………………………………………………..5
DMX Profile ................................................................................................6
Main Control Menu......................................................................................7
Rigging the Fixture……………………………………………………………...8
Cleaning & Maintenance.............................................................................8
Parts List.....................................................................................................8
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured away from unit movement.
6. Maximum surface operating temperature 104º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3
Technical Information
Part Numbers
Fixture
7030-CW
7030-WW
7030-GH
7030-JH
Drama Z Narrow 200 Cool White
Drama Z Narrow 200 Warm White
Removable Gobo Holder (included)
Removable Gel Holder (included)
Mechanical Specifications
29.33”
DMX Connectors: 3 and 5 pin XLR connectors in/out
Power Connections: Neutrik Power con In and Out
4 Ft 7 Inch PowerCon to Nema Cable Power Cable:
Thermal: Maximum ambient temperature 104°
Maximum surface temperature 140°
Display: Digital LED
Fastening System: Mounting Yoke
Fixture Packaged for Shipping
Size: 29.33”L x 10.75”W x 16.16”H
Weight: 24 lbs
Size: 31” X 12.5” X 12.5”
Weight: 29 lbs
Electrical Specifications
LED Type:
LED Watts:
LED Color Temp:
CRI:
LED Lifetime:
Zoom:
Fan:
1 COB LED
200
CW= Cool White 5600K
WW= Warm White 3200K
≥85Ra
60,000 to 100,000 hours
Manual Zoom from 15º to 28º
Heat Pipe Cooling with low noise fan
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Power Consumption Watts:
Amps:
242
2.12
17.75”
Control & Programming
Protocol:
DMX Channels:
Operating mode:
DMX 512
2 Operating Modes
2 Channel Dimmer, Zoom
3 Channel Dimmer, Zoom, Strobe
Stand alone 255 step Dimmer setting via display. Zoom Control via Zoom in/out buttons in the rear
8.25” / 10.75” /with Knobs
8.5”
4.16”
12”
4
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to
Cable (USA) Cable (EU) Pin 110V 220V
Black
White
Brown
Light Blue
Live
Neutral
L
N
L
L
Green Yellow/Green Ground
110V—Connection
N L
220V—Connection
L L
DMX-512 Connection
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.
DMX—input DMX—output
1
3
2 1
2
3
5
4
1. Shield
2. Signal (-)
3. Signal (+)
4. N/A
5. N/A
2
3
1 5
4
3
1
2
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a
120 Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-Lite dealer (P-DMXT).
5
DMX Profile
Drama Z 200 N Mode 1 CH
DMX Chanel Function Description
1
2
Dimmer
Zoom
LED intensity
Linear Zoom
Drama Z 200 N Mode 2 CH
DMX Chanel Function Descriptions
2
1
2
Dimmer
Zoom
Strobe
LED intensity
Linear Zoom
No Function
Strobe (slow to fast)
Pulse On (slow to fast)
Pulse Off (slow to fast)
Random Strobe (slow to fast)
Value
0-255
0-255
Value
0-255
0-255
0
1-127
128-159
160-191
192-255
6
Main Control
The control board on the fixture base is your interface to access and control all the functions on the unit. It’s digital display gives you a code view of the options and functions. The following will explain each function and its options.
Address
001
Reset
Function
Master
Function
Perform
Function
Channel
Mode
ManDim
000
Version
000
ESC ENTER DOWN UP
This function allows you to set your DMX Start Channel. First make sure you have a proper DMX connection from your controller using the 3 or 5 pin XLR connection. If there is no DMX connection the red LED indicator will flash. If there is proper DMX connection the red LED indicator will be off.
To Set the DMX Start Channel press Enter. Use the Down or Up to select the desired DMX Start Channel and press Enter to confirm your setting.
To reset the fixture press Enter. Use the Up or Down for Yes or No press Enter to confirm your setting.
This function allows the unit to output DMX signal to operate the same as the
Master unit. All preset settings will be copied the other fixtures.
Press Enter. Use the Up or Down for Yes or No press Enter to confirm your setting.
Note: All other fixtures must be connected via XLR Connection. And must be put on DMX address Channel 001
This function allows the unit to activate the built in programs.
Press Enter. Use the Up or Down for 000,001 or 002 press Enter to confirm your setting.
You can record a scene by selecting the performance function you want to use from 0 to 2. Then accessing the ManDim function and setting the desired intensity then press Enter to confirm.
The fixture was a capability to operate in 2 different modes of DMX control. Mode
1CH is Dimmer , Mode 2CH is Dimmer and Strobe
Press Enter. Use the Up or Down for 1CH or 2CH press Enter to confirm your setting.
This function let you set the Dimmer intensity via display.
Press Enter. Use the Up or Down from 000 to 255 press Enter to confirm your setting.
Operating Software
7
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least one time a year by a skilled person.
Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to be carried out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating. F3.15AL250
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
7025-FAN
7030-MPCB
7030-PS
7030-DIS
7025-FB
7025-RB
7030-FL
7025-KNOB
Large Replacement fan
Main PCB card
Power Supply
Display
Front Bessel Plastic Replacement
Rear Bessel Plastic Replacement
Front lens
Knob Set
7030-GH
7030-GEH
Removable Gobo Holder
Removable Gel Holder
8
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LEDs are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, incidental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax 210-855-6279 www.mega-lite.com / [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project