Bosch GSM 509 Specifications

4
Conettix ITS-DX4020-G
GPRS/GSM IP Communicator
Connect to the Control Panel
Connect the ITS-DX4020-G to the control panel as shown below.
• Dual Wireless Mode (IP over GPRS and Contact ID over GSM): Easy Series
• IP over GPRS Mode: All compatible control panels
• PSTN (Contact ID) over GSM: DS7200V2, DS7400XiV4, Easy Series, FPD-7024, GV3 Series, GV4 Series, ICP-CMS8CHI, ICP-CMS6-CHI
Quick Start Guide
PSTN (Contact ID) over GSM Mode
MODELO: ITS-DX4020-G
2113-12-5164
B
G
Y
R
For complete installation, configuration, and testing instructions,
refer to the Conettix ITS-DX4020-G Installation and Operation
Guide (P/N: F01U133268) provided on the supplied CD-ROM.
( 01) 07891009538471
Control Panel Compatibility
Certifications
DS7200V2 Series
Version 2.10 or later
ANATEL
No. 2113-12-5164
DS7400XiV4
Version 4.10 or later
Australia
A-Tick Approved
FPD-7024
All versions
CE
- EN60950 Safety
(-) (+)
Easy Series
Version 3.0 or later
GV2 Series
D9412GV2, D7412GV2, D7212GV2
GV3 Series
D9412GV3, D7412GV3, D7212GV3
INCERT
No. B-509-0005/d
GV4 Series
D9412GV4, D7412GV4, D7212GV4
Norwegian
FGI: T-127/09, ATS4, grade 3
DS7200V2 Series
DS7400XiV4
Easy Series
FPD-7024
GV2 Series
GV3 Series
GV4 Series
ICP-CMS6-CHI
ICP-CMS8-CH
- EN50130-4 Electromagnetic Compatability
- EN55022 Radiated/Conducted Emissions
ICP-CMS6-CHI
ICP-CMS8-CHI
R
RH
TH
T
DS7200V2 Series
DS7200V2 Series
DS7400XiV4
DS7400XiV4
Easy
Series
FPD-7024
Easy Series
GV3
Series
FPD-7024
ITS-DX4020-G
GV3 Series
GV4 Series
NOTE: For Dual Wireless Mode, use the PSTN (Contact ID) over GSM Mode figure, but include all four data bus wires.
1
Disconnect the Power
Before installing the ITS-DX4020-G, disconnect
all power to the control panel (AC and standby
battery).
2
Insert the SIM Card
1. Open the SIM card holder.
3
Mount the ITS-DX4020-G
1. Mount the ITS-DX4020-G on the control panel
enclosure using the supplied mounting screws.
Use any of the standard three-hole mounting
patterns on the control panel enclosure. If
necessary, remove the three mounting knockouts.
2. Mount the magnetic antenna to a metallic surface.
3. Connect the antenna cable to the threaded
ANTENNA connector on the ITS-DX4020-G.
5
Apply Power
Connect power to the system (AC and standby battery).
6
Check Signal Strength
2. Insert the SIM card into the card guide.
Check the signal strength LEDs (SS1, SS2, and SS3).
3. Close the SIM card holder.
•
If signal strength is acceptable, you are ready to configure the ITS-DX4020-G.
•
If signal strength is unacceptable, check the site for possible causes of signal interference.
NOTE: Depending on the SIM card used, first-time registration might take up to 3 minutes to complete. When the SIM
card registration is complete, the signal strength LEDs will light.
SS1
SS2
SS3
SS1
SS2
SS3
SS1
SS2
SS3
SS1
SS2
SS3
SS1
SS2
SS3
=
www.boschsecuritysystems.com
=
=
=
=
© 2012 Bosch Security Systems, Inc.
2012.10
F01U274446-02 en
1
7
8
Configure the ITS-DX4020-G
Test the ITS-DX4020-G
You can configure the ITS-DX4020-G by sending a text message from your mobile phone or by using the USB interface from a PC or laptop.
Contact the central monitoring station for destination IP address and port number settings. Provide
the central monitoring station with the poll rate setting.
SMS (Text Message) Configuration
Test the system to ensure that it can send reports from the ITS-DX4020-G to the central monitoring
station in the selected mode of operation.
1. Place the supplied jumper plug across the CONFIG MODE jumper pins.
2. Compose the SMS (see the table below for sample messages).
3. Send the SMS to the phone number assigned to the SIM card in the ITS-DX4020-G.
LED
Function
4. Check the diagnostic LEDs on the ITS-DX4020-G to ensure that the SMS was properly received.
STATUS
Indicates the overall health of the device.
•
ON: Normal operation.
•
Flash: A trouble condition exists.
•
OFF: No power to the device.
When the LED DIS jumper pins are first shorted, the STATUS LED flashes the firmware version. After that, the STATUS
LED flashes once every 4 sec to indicate that the ITS-DX4020-G is powered up.
CELL IP
Indicates the IP connection status.
•
ON: The ITS-DX4020-G is connected to the central station receiver through the GPRS network.
•
Flash: The ITS-DX4020-G is connected to the GPRS network, but not to the central station receiver.
•
OFF: The ITS-DX4020-G is not connected to the GPRS network, or the module is configured for Contact ID over
GSM.
AUDIO ACT
Indicates the PSTN connection status.
•
ON: The PSTN connection is in use (off-hook).
•
OFF: The PSTN connection is not in use (on-hook).
SS1, SS2,
SS3
These LEDs indicate the wireless signal strength of the ITS-DX4020-G.
•
Registering on the GSM network: SS1 flashes, SS2 and SS3 OFF
•
Unacceptable: All three LEDs are off; or SS1 ON, SS2 and SS3 OFF
•
Marginal: SS1 ON, SS2 flashes, SS3 OFF
•
Good: SS1 and SS2 ON, SS3 OFF
•
Very Good: SS1 and SS2 ON, SS3 flashes
•
Excellent: All three LEDS ON
BUS
Indicates bus connection status.
•
ON: Active communication exists between the ITS-DX4020-G and the control panel.
•
Flash: The ITS-DX4020-G is initializing, or a problem exists with the bus connection to the control panel.
•
OFF: The ITS-DX4020-G is not configured for bus communication.
5. When the ITS-DX4020-G is successfully configured, remove the jumper plug from the CONFIG MODE pins. The ITS-DX4020-G restarts.
4
SMS
CONFIG
MODE
= LED Off
1
ON
=
STATUS
5
AUDIO
ACT
SS1
SS2
SS3
BUS
= LED On
= LED Flashing
OFF
SMS
=
STATUS
2
CELL
IP
CELL
IP
AUDIO
ACT
SS1
SS2
SS3
Separate each command line in the SMS with either a line feed <LF>, a carriage return <CR> or <
BUS
ENTER>, or a semi-colon (;).
Any of these characters is acceptable to separate command lines. Refer to your cellular phone’s documentation for available characters.
Dual Wireless Mode
ITS-DX4020-G
SMS Settings
Easy Series
PSTN (Contact ID)
Over GSM Mode
IP Over GPRS Mode
DS7200V2/
Easy Series/
ICP-CMS8-CHI/ICPCMS6-CHI
DS7400Xi
FPD-7024
For control panels
that support Contact
ID
GV2/GV3/GV4 Series
%1 = Start SMS
%1
%1
%1
%1
%1
%1
1 = Password
1=4020G
1=4020G
1=4020G
1=4020G
1=4020G
1=4020G
10=<your APN>
10=<your APN>
10=<your APN>
10=<your APN>
10=<your APN>
4 = SIM PIN (if required)
10 = GPRS APN

11 = GPRS Username
(if required)
12 = GPRS Password
(if required)
14 = Bus Address
14=134 (default)
14=13
14=250
14=88 (92 for GV3/GV4)
14=0
17 = Comm Path
17=2
17=2
17=2
17=2
17=3
!
!
!
!
!
Installation Complete
Technical Specifications
Electrical
! = End SMS
!
Operating Current
•
•
USB Configuration
Operating Voltage
12 VDC nominal
For complete USB configuration instructions, refer to the Conettix ITS-DX4020-G Installation and Operation Guide on the supplied CD-ROM.
Maximum Wire Resistance for
Control Panel Connections
1.6 ohms
Maximum Wire Distance
•
•
1. Connect the ITS-DX4020-G to the target PC or laptop with a USB-to-mini-USB cable (not supplied).
2. Download the ITS-DX4020-G.inf file from the supplied CD-ROM and install it on the target PC or laptop.
Standby: 65 mA
Alarm: 200 mA
22 AWG: 30.5 m (100ft)
18 AWG: 61 m (200 ft)
3. On the ITS-DX4020-G, short the CONFIG MODE jumper pins with the supplied jumper plug.
Ripple/Noise
200 mVpp maximum
4. From Windows, start a terminal session (use HyperTerminal or Tera Term).
PSTN FSX Port
17 V minimum supplied
Radio
GSM Quad band radio; 850 MHz and 1900 MHz
5. In the terminal session, configure a new virtual serial COM port (for example, COM4):
Baud rate: 9600; Data bits: 8; Parity: None; Stop bits: 1; Flow control: None
Other
Antenna
•
•
7. Enter the login password (default: 4020G all uppercase) and press [Enter].
SIM Card
8. Configure the ITS-DX4020-G as needed using USB menu Options 8 (Change Basic Parameters).
The table above shows the parameters that must be set as a minimum.
3 V/1.8 V SIM (compliant with GSM 11.12
recommendation)
USB
Mini-B connector (cable not supplied)
6. Press [Enter] on the keyboard. The USB Login window opens.
9. When configuration is complete, select Option 6 (Save and Reboot) from the USB menu to save all changes and to restart the ITS-DX4020-G.
Magnetic base omni-directional antenna
2.5 m (8.2 ft) cable with SMA connector
© 2012 Bosch Security Systems, Inc.
2012.10
F01U274446-02 en
2