Asus Terminator 2 Barebone System T2-R System information

Terminator 2
MODE
Copyright(C)2004 ASUSTeK COMPUTER INC. All Rights Reserved.
2
3
®
4
5
This device complies with FCC Rules Part 15. Operation is subject to the
following two conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
6
VORSICHT: Explosionsgetahr bei unsachgemßflen Austausch der
Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
7
Safeguards
8
1.
2.
9
10
MODE
11
®
1
1
2
®
2
3
3
4
4
9
10
MODE
11 12 13 14
MODE
15 16 17 18
12
5
5
6
6
7
7
8
8
®
13
14
19
20
19
20
21
22
23
24
MODE
27 28 29 30
25 26
25 26
27
30
®
®
®
®
®
®
15
2.0
16
1
2
15
3
4
5
16
6
7
8
17
9
10
18
11
19
12
13
20
14
21
22
23 24
17
2.0
18
19
1
3
6
2
4
9
8
5
7
10
11
20
12
21
22
MODE
23
SB_PWR
P4P8T
P4P8T Onboard LED
24
®
ON
Standby
Power
OFF
Powered
Off
1
1
1
2
2
2
4
3
3
25
3
6
4
5
7
7
26
®
®
1
2
3
4
27
7
6
3
4
2
5
1
28
1
3
2
4
7
5
29
30
512MB
Samsung
M368L6432ETM-CCC
Samsung
K4H560838E-TCCC
256MB
Infineon
HYS64D32300GU-5-B
Infineon
HYB25D256800BT-5B
512MB
Infineon
HYS64D64320GU-5-B
Infineon
HYB25D256800BT-5B
256MB
Transcend
TS32MLD64V4F3
Samsung
K4H560838D-TCC4
512MB
256MB
512MB
256MB
256MB
512MB
512MB
Transcend
Winbond
Winbond
A DATA
TwinMOS
Hynix
Apacer
TS64MLD64V4F3
W9425GCDB-5
W9451GCDB-5
MDOAD5F3G315B1ECZ
MDSTTUF08108L294K4FW0/T
HYMD264646B8J-D43 AA
77.10636.465
Samsung
Winbond
Winbond
Samsung
TwinMOS
Hynix
Samsung
K4H560838D-TCC4
W942508CH-5
W942508CH-5
K4H560838D-TCC4
TMD7608F8E50B
HY5DU56822BT-D43
K4H560838D-TCC4
800 MHz
PC3200/PC2700*/PC2100
400/333*/266 MHz
533 MHz
PC2700/PC2100
333/266 MHz
400 MHz
PC2100
266 MHz
3
2
2
4
4
1
31
P4P8T
®
P4P8T Accelerated Graphics Port (AGP)
32
Keyed for 1.5v
2
3
4
5
33
IRQ
0
1
2
3*
4*
5*
6
7*
8
9*
10*
11*
12*
13
14*
15*
1
2
N/A
11
12
13
14
15
3
4
5
6
7
8
9
10
(COM2)
(COM1)
(LPT2
(LPT1)
CMOS/
ACPI
PCI
PCI
PS/2
1
2
A
B
IRQ
IRQ
IDE
IDE
C
D
E
F
G
H
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
34
)
—
—
—
3
3
1
2
3
3
4
4
5
6
7
35
8
10
9
13
14
36
1
2
3
5
4
5
37
6
7
8
9
38
1
3
2
4
5
39
7
8
1
1
6
230
40
3
4
2
5
41
42
43
44
MODE
45
®
MODE
®
46
®
47
48
®
®
®
49
50
‘
51
52
®
53
®
54
55
56
CD
ON/OFF
PLAY/PAUSE
Esc
F1
STOP/EJECT
F2
PREVIOUS
NEXT
F3
F4
VOL. DOWN
F5
VOL. UP
F6
CAPS
LOCK
LED
CD ON/OFF
PLAY/PAUSE
STOP/EJECT
PREVIOUS
VOL. DOWN
F7
F8
SCROLL
LOCK
LED
NEXT
VOL. UP
57
®
®
®
®
®
\
58
\
\
®
59
60
®
®
61
62
63
®
(Soft AP)
64
65
66
67
68
69
®
70
(
Ad-hoc)
(
Ad-hoc)
71
72
®
73
74
MODE
75
24.89cm (9.8in)
Mic
In
Intel
865G
ATX12V
USB2.0
T: USB1
B: USB2
Super
I/O
CR2032 3V
Lithium Cell
CMOS Power
USB2.0 Top:
T: USB3 RJ-45
B: USB4
AD1888
20.06cm (7.9in)
Line
In
FLOPPY
Line
Out
Flash
BIOS
SEC_IDE
PRI_IDE
DDR DIMM_A1 (64/72-bit, 184-pin module)
PARALLEL PORT
CPU_FAN
CHA_FAN
DDR DIMM_B1 (64/72-bit, 184-pin module)
Socket 478
VGA1
ATX Power Connector
IOC_MB
PS/2
T:Mouse
B:Keyboard
AGP1
MDC
Intel
ICH5
USB56
FP_AUDIO
SPDIF OUT
PCI Slot 1
SATA2
SATA1
USB78
CLRTC
BUZZER
SB_PWR
AUX1
76
CD1
P4P8T
®
PANEL
CLRTC
1 2
P4P8T
2 3
®
P4P8T Clear RTC RAM
Normal
(Default)
Clear CMOS
77
P4P8T
78
®
P4P8T Front Panel Audio Connector
USB Power
USBP3–
USBP3+
GND
P4P8T USB Port
BLINE_OUT_R
+5VA
AGND
Line out_L
NC
Line out_R
MICPWR
MIC2
P4P8T
®
BLINE_OUT_L
USB56
1
5
6
10
FP_AUDIO
USB Power
USBP2–
USBP2+
GND
NC
P4P8T
SPDIFOUT
GND
+5V
SPDIF OUT
®
P4P8T Digital Audio Connector
USB Power
USBP2–
USBP2+
GND
NC
USB78
®
5
6
10
USB Power
USBP3–
USBP3+
GND
P4P8T
1
P4P8T USB Port
79
MDC
1
P4P8T
PHONE
AC_SYNC
AC_SDIN1
GND
MDC_BITCLK
GND
+3VSB
AC_RST#
AC_SDOUT
®
P4P8T MDC Connector
GAME
COM1
®
CGAEX
IOC_DC
P4P8T
®
P4P8T IOC_MB Connector
80
CPU_FAN
GND
+12V
Rotation
CHA_FAN
GND
+12V
Rotation
P4P8T
®
P4P8T Fan Connectors
ATXPWR
+12.0Volts
+5V Standby
Power Good
Ground
+5.0 Volts
Ground
+5.0 Volts
Ground
+3.3 Volts
+3.3 Volts
+5.0 Volts
+5.0 Volts
-5.0 Volts
Ground
Ground
Ground
Power Supply On
Ground
-12.0Volts
+3.3Volts
ATX12V
P4P8T
®
P4P8T ATX Power Connector
+12V DC
COM
+12V DC
COM
81
P4P8T
PRI_IDE
SEC_IDE
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
®
P4P8T IDE Connectors
PIN 1
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA2
P4P8T
®
P4P8T SATA Connectors
82
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA1
®
®
®
P-ATA
2
1
(2
)
S-ATA
0
(2
)
(1
)
1
(1
)
1. Windows® 2000/XP
2. Windows® 98SE/ME
Configuration A
—
Configuration B
—
Configuration C
—
—
—
:
BIOS
Windows®
2000/XP
Windows® 98SE/ME
B
A
C
IDE
S-ATA
IDE
-
-
-
Primary P-ATA+S-ATA
Sec. P-ATA+S-ATA
P-ATA
83
P4P8T Internal Audio Connectors
Ground
Left Audio Channel
Right Audio Channel
®
Ground
Left Audio Channel
P4P8T
Right Audio Channel
AUX1 (White) CD1 (Black)
FLOPPY
PIN 1
P4P8T
®
P4P8T Floppy Disk Drive Connector
84
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
Power LED
IDE_LEDIDE_LED+
PLEDPLED+
IDE_LED
Ground
PWR
PANEL
ATX Power
Switch*
P4P8T
®
* Requires an ATX power supply.
P4P8T System Panel Connector
85
86
MODE
87
®
®
88
A:\>afudos /oMYBIOS03.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... 0x0008CC00 (9%)
A:\>afudos /oMYBIOS03.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
A:\>
89
"
"
A:\>afudos /ip4p8t.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading file ..... done
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
90
A:\>afudos /ip4p8t.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading file .....
Erasing flash ....
Writing flash ....
Verifying flash ..
done
done
0x0008CC00 (9%)
done
A:\>
91
User recovery requested. Starting BIOS recovery...
Checking for floppy...
User recovery requested. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “p4p8t.rom”. Completed.
Start flashing...
Flashed successfully. Rebooting.
92
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “p4p8t.rom”. Completed.
Start flashing...
93
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found.
Reading file “p4p8t.rom”. Completed.
Start flashing...
94
®
95
96
97
System Time
System Date
Legacy Diskette A
Language
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
Fourth IDE Master
IDE Configuration
System Information
98
[11:10:19]
[Thu, 09/27/2003]
[1.44M, 3.5 in.]
[English]
[ST321122A]
[ASUS CDS520/]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select a
field.
Use [+] or [-] to
configure system time.
99
System Time
System Date
Legacy Diskette A
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
Fourth IDE Master
IDE Configuration
[11:10:19]
[Thu, 09/27/2003]
[1.44M, 3.5 in.]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select a
field.
[ST321122A]
[ASUS CDS520/]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Use [+] or [-] to
configure system time.
System Information
System Time [xx:xx:xxxx]
System Date [Day xx/xx/xxxx]
Legacy Diskette A [1.44M, 3.5 in.]
100
Primary IDE Master
Select the type of
device connected to the
system.
Device
: Hard Disk
Vendor
: ST320413A
Size
: 20.0GB
LBA Mode
: Supported
Block Mode
: 16 Sectors
PIO Mode
: Supported
Async DMA
: MultiWord DMA-2
Ultra DMA
: Ultra DMA-5
SMART Monitoring: Supported
Type
LBA/Large Mode
Block (Multi-sector Transfer)
PIO Mode
DMA Mode
Smart Monitoring
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
Type [Auto]
LBA/Large Mode [Auto]
Block (Multi-sector Transfer [Auto]
101
PIO Mode [Auto]
DMA Mode [Auto]
SMART Monitoring [Auto]
32Bit Data Transfer [Disabled]
IDE Configuration
Onboard IDE Operate Mode
Enhanced Mode Support On
IDE Detect Time Out (Sec)
[Enhanced Mode]
[S-ATA]
[35]
Set [Compatible Mode]
when legacy OS (i.e.
WIN ME, 98, NT4.0, MS
DOS is used.
Set [Enhanced Mode]
when Native OS (i.e.
WIN2000, WIN XP) is
used.
Onboard IDE Operate Mode [Enhanced Mode]
102
Enhanced Mode Support On [S-ATA]
IDE Detect Time Out [35]
AMI BIOS
Version
: 08.00.09
Build Date : 09/03/03
ID
: P4P8T113
Processor
Type
Speed
Count
: Intel(R) Pentium(R) 4 Family CPU 2.40G
: 2600MHz
: 1
System Memory
Size
: 256MB
AMI BIOS
Processor
System Memory
103
CPU Configuration
Chipset
Onboard Devices Configuration
PCI PnP
USB Configuration
Instant Music Configuration
Configure CPU.
Configure advanced CPU settings
Manufacturer
Brand String
Frequency
FSB Speed
:
:
:
:
Intel(R)
Intel(R) Pentium(R) 4 Family CPU 2.40G
2400MHz
400MHz
Cache L1
Cache L2
Cache L3
: 8 KB
: 128 KB
: 0 KB
Ratio Status : Unlocked
Ratio Actual Value
: 26
Ratio CMOS Setting
L3 Cache
Max CPUID Value Limit
[26]
[Enabled]
[Disabled]
Hyper-Threading Technology
[Enabled]
Ratio CMOS Setting [26]
104
Sets the ration between
CPU Core Clock and the
FSB Freuency.
Note: If an invalid
ratio is set in CMOS,
then actual and setpoint
values may differ.
L3 Cache [Enabled]
Max CPUID Value Limit [Disabled]
Hyper-Threading Technology [Enabled]
Advanced Chipset settings
Set DDR reference
voltage.
WARNING: Setting wrong values in the sections below
may cause system to malfunction.
DDR Reference Voltage
DRAM Frequency
Configure DRAM Timing by SPD
Internal Graphic Acceleration Mode
[Auto]
[Auto]
[Enabled]
[Auto]
Graphic Adapter Priority
Onboard Video Memory
Graphics Aperture Size
[AGP/Int-VGA]
[Enabled, 8MB]
[ 64MB]
Boot Display Device
Flat Panel type
TV Standard
[Auto]
[640x480LVDS]
[Auto]
MPS Revision
[1.4]
DDR Reference Voltage [Auto]
105
DRAM Frequency [Auto]
Configure DRAM Timing by SPD [Enabled]
DRAM CAS# Latency [2.5 Clocks]
DRAM RAS# Precharge [4 Clocks]
DRAM RAS# to CAS# Delay [4 Clocks]
DRAM Precharge Delay [8 Clocks]
DRAM Burst Length [8 Clocks]
Internal Graphic Acceleration Mode [Auto]
Graphic Adapter Priority [AGP/Int-VGA]
106
Onboard Video Memory [Enabled, 8MB]
Graphics Aperture Size [64MB]
Boot Display Device [Auto]
Flat Panel Display [640x480LVDS]
TV Standard [Auto]
MPS Revision [1.4]
107
OnBoard AC’97 Audio
OnBoard LAN
OnBoard LAN Boot ROM
[Auto]
[Enabled]
[Disabled]
Serial Port1 Address
Parallel Port Address
Parallel Port Mode
EPP Version
ECP Mode DMA Channel
Parallel Port IRQ
OnBoard Game Port
Onboard MIDI Port
[3F8/IRQ4]
[378]
[EPP+ECP]
[1.9]
[DMA3]
[IRQ7]
[Enabled]
[Disabled]
OnBoard AC’97 Audio [Auto]
OnBoard LAN [Enabled]
Serial Port1 Address [3F8/IRQ4]
Parallel Port Address [378]
Parallel Port Mode [EPP+ECP]
108
EPP Version [1.9]
ECP Mode DMA Channel [DMA3]
Parallel Port IRQ [IRQ7]
Onboard Game Port [Enabled]
Onboard MIDI Port [Disabled]
109
Advanced PCI PnP settings
WARNING: Setting wrong values in the sections below
may cause system to malfunction.
Plug and Play OS
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
[No]
[64]
[Yes]
[Disabled]
[Enabled]
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Plug and Play O/S [No]
PCI Latency Timer [64]
Allocate IRQ to PCI VGA [Yes]
110
NO: Lets the BIOS
configure all the
devices in the system.
YES: Lets the
operating system
configure Plug and
Play (PnP) devices not
required for boot if
your system has a Plug
and Play operating
system.
Palette Snooping [Disabled]
PCI IDE BusMaster [Enabled]
IRQ xx [Available]
111
USB Configuration
Module Version
Enables USB host
controllers.
: 2.22.4-5.3
USB Devices Enabled : None
USB Function
Legacy USB Support
USB 2.0 Controller
USB 2.0 Controller Mode
[8 USB Ports]
[Auto]
[Enabled]
[FullSpeed]
USB Mass Storage Device Configuration
USB Function [8 USB Ports]
Legacy USB Support [Auto]
USB 2.0 Controller [Enabled]
USB 2.0 Controller Mode [FullSpeed]
112
USB Mass Storage Device Configuration
USB Mass Storage Reset Delay
[20 Sec]
No USB Mass Storage device detected
Device #1
Emulation
Device #2
Emulation
Device #3
Emulation
Device #4
Emulation
Device #5
Emulation
Device #6
Emulation
Type
Type
Type
Type
Type
Type
Number of seconds
POST waits for the USB
mass storage device
after that start unit
command.
N/A
[N/A]
N/A
[N/A]
N/A
[N/A]
N/A
[N/A]
N/A
[N/A]
N/A
[N/A]
USB Mass Storage Reset Delay [20 Sec]
Emulation Type [N/A]
113
Instant Music Configuration
Instant Music
Disable/Enable Instant
Music feature.
[Disabled]
Instant Music [Disabled]
Instant Music CD-ROM Drive [IDE Secondary Master]
Radio Region [EUROPE]
114
Suspend Mode
Repost Video on S3 Resume
ACPI 2.0 Support
ACPI ASIC Support
[Auto]
[No]
[No]
[Enabled]
Select the ACPI state
used for System Suspend.
APM Configuration
Hardware Monitor
Suspend Mode [Auto]
Repost Video on S3 Resume [No]
ACPI 2.0 Support [No]
ACPI APIC Support [Enabled]
115
APM Configuration
Go into On/Off, or
Suspend when Power button
is pressed.
Restore on AC Power Loss
[Power Off]
Power
Power
Power
Power
[Disabled]
[Disabled]
[Disabled]
[Disabled]
On
On
On
On
By
By
By
By
PS/2 Device
External Modems
PCI Devices
RTC Alarm
Restore on AC Power Loss [Power Off]
Power On By PS/2 Devices [Disabled]
Power On By External Modems [Disabled]
116
Power On By PCI Devices [Disabled]
Power On By RTC Alarm [Disabled]
CPU temperature.
Hardware Monitor
CPU Temperature
MB Temperature
[44° C/111° F]
[36° C/96.5° F]
CPU Fan Speed
Chassis Fan Speed
[5234RPM]
[N/A]
VCORE Voltage
3.3V Voltage
5V Voltage
12V Voltage
[1.808V]
[3.376V]
[5.080V]
[11.977V]
SMART Q-Fan Function
[Enabled]
Fan Auto Start Voltage
[5.0V]
Fan Auto Mode Start Temp
[30° C]
Fan Auto Mode Full Speed Temp [70° C]
CPU Temperature [xxxºC/xxxºF]
MB Temperature [xxxºC/xxxºF]
CPU Fan Speed [xxxxRPM] or [N/A]
Chassis Fan Speed [xxxxRPM] or [N/A]
117
VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage
SMART Q-Fan Function [Enabled]
Fan Auto Mode Start Voltage [5.0V]
Fan Auto Mode Start Temp [30ºC]
Fan Auto Mode Full Speed Temp [70ºC]
118
Boot Settings
Boot Device Priority
Removable Drives
CDROM Drives
Boot Settings Configuration
Security
Boot Device Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
[First Floppy Drive]
[PM-ST320413A]
[PS-ASUS CD-S340]
Specifies the boot
sequence from the
available devices.
A device enclosed in
parenthesis has been
disabled in the
corresponding type
menu.
1st ~ xxth Boot Device [1st Floppy Drive]
119
Removable Drives
1st Drive
[1st Floppy Drive]
Specifies the boot
sequence from the
available devices.
1st ~ xxth Drive [1st Floppy Drive]
CDROM Drives
1st Drive
2nd Drive
[SM-ASUS DRW-0402P/D]
[SS-ASUS CD-S520/A]
1st ~ xxth Drive [SM-Optical Drive Name]
120
Specifies the boot
sequence from the
available devices.
Boot Settings Configuration
Quick Boot
Full Screen Logo
Add On ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Typematic Rate
Boot to OS/2
Wait for ‘F1’ If Error
Hit ‘DEL’ Message Display
Interrupt 19 Capture
[Enabled]
[Enabled]
[Force BIOS]
[On]
[Auto]
[Fast]
[No]
[Enabled]
[Enabled]
[Disabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
Quick Boot [Enabled]
Full Screen Logo [Enabled]
Add On ROM Display Mode [Force BIOS]
Bootup Num-Lock [On]
PS/2 Mouse Support [Auto]
121
Typematic Rate [Fast]
Boot to OS/2 [No]
Wait for ‘F1’ If Error [Enabled]
Hit ‘DEL’ Message Display [Enabled]
Interrupt 19 Capture [Disabled]
122
Security Settings
Supervisor Password
User Password
Not Installed
Not Installed
<Enter> to change
password.
<Enter> again to disable
password.
Change Supervisor Password
Boot Sector Virus Protection
[Disabled]
123
Security Settings
Supervisor Password
User Password
Not Installed
Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
[Setup]
Boot Sector Virus Protection
[Disabled]
[Full Access]
User Access Level [Full Access]
124
<Enter> to change
password.
<Enter> again to disable
password.
Clear User Password
Password Check [Setup]
Boot Sector Virus Protection [Disabled]
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
Exit system setup after
saving the changes.
F10 key can be used for
this operation.
Load Setup Defaults
Exit & Save Changes
125
Exit & Discard Changes
Discard Changes
Load Setup Defaults
126
Appendix
MODE
A-1
A-2
Australia (ACA)
Belgium (RTT&E/EMC/LVD)
Bulgaria (RTT&E/EMC/LVD)
Canada (CSA/cUL 950 3rd Edition)
China (MII)
Cyprus (RTT&E/EMC/LVD)
Czech Republic (RTT&E/EMC/LVD)
Denmark (RTT&E/EMC/LVD)
Finland (RTT&E/EMC/LVD)
France (RTT&E/EMC/LVD)
Germany (RTT&E/EMC/LVD)
Greece (RTT&E/EMC/LVD)
Hong Kong (OFTA)
Hungary (RTT&E/EMC/LVD)
Iceland (RTT&E/EMC/LVD)
A-3
Ireland (RTT&E/EMC/LVD)
Italy (RTT&E/EMC/LVD)
Japan (TELEC)
Luxembourg (RTT&E/EMC/LVD)
Malaysia (SIRIM/CMC)
Mexico
Netherlands Antilles (RTT&E/EMC/LVD)
Netherlands/Holland (RTT&E/EMC/LVD)
New Zealand (PTC)
Norway (RTT&E/EMC/LVD)
Portugal (RTT&E/EMC/LVD)
Saudi Arabia
Singapore
South Korea (KS)
Spain (RTT&E/EMC/LVD)
Sweden (RTT&E/EMC/LVD)
Switzerland (RTT&E/EMC/LVD)
Taiwan (DGT)
Turkey (TTAS)
United Kingdom (RTT&E/EMC/LVD)
United States (FCC)
A-4