Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com.
Owner’s Manual
Installation and Operation
Models:
ST-36TRB-IPI
PIER-36TRB-IPI
LCOR-36TRB-IPI
RCOR-36TRB-IPI
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
A. Congratulations
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Heat & Glo gas fireplace, an
elegant and clean alternative to wood burning fireplaces.
The Heat & Glo gas fireplace you have selected is designed
to provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Heat & Glo gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fireplace products!
We recommend that you record the following pertinent
information about your fireplace.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on fireplace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Type of Gas
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz)
Gaz)::
NATURAL GAS
Gas and Electric
Information
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Model Number
Serial Number
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
 B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
7
7
7
7
7
7
7
8
User Guide
7 Vent Information and Diagrams
A.
B.
C.
D.
E.
Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
25
25
26
8 Vent Clearances and Framing
A.
B.
C.
D.
E.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Continue Adding Vent Components . . . . . . . . . . . . . . . . .
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . .
Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
36
36
37
38
39
2 Operating Instructions
9 Appliance Preparation
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 42
Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Blower Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Controls, Wall Controls and Wall Switches . . . . . 10
Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11
After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13
B. Maintenance Tasks-Qualified Service Technician . . . . . . 14
Installer Guide
4 Getting Started
A.
B.
C.
D.
Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . .
Design and Installation Considerations . . . . . . . . . . . . . .
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . .
Inspect Appliance and Components . . . . . . . . . . . . . . . . .
10 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap (DVP and SLP Pipe) .
43
44
44
45 
45
46
47
47
48
48
48
49
11 Gas Information
16
17
17
17
5 Framing and Clearances
 A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 18
B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 19
C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
D. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 21
6 Termination Locations
A.
B.
C.
D.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
50
50
50
50
12 Electrical Information
A.
B.
C.
D.
E.
F.
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . .
Optional Accessories Requirements . . . . . . . . . . . . . . . .
Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . .
Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Switch Installation for Fan (Optional) . . . . . . . . . . . .

51
51
51
51
53
53
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 23
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
3
13 Finishing
A.
B.
C.
D.
E.
Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finishing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . .
54
56
57
57
59
14 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . .
Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lava Rock and Glowing Ember Placement . . . . . . . . . . .
Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Trim Kits and Surrounds . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
60
60
60
60
61
63
63
63
15 Troubleshooting
 A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 64
16 Reference Materials
 A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 66
 B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 69
 D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
 = Contains updated information.
4
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13

B. Limited Lifetime Warranty
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (”HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
HHT Manufactured Appliances and Venting
Gas
X
2 years
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
X
Firepots and burnpots
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645F 02-18-13
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Page 1 of 2
5

B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
•
•
•
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
This warranty is only valid while the HHT appliance remains at the site of original installation.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
•
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645F 02-18-13
6
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Page 2 of 2
1
Listing and Code Approvals
A. Appliance Certification
MODELS: ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI,
RCOR-36TRB-IPI
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88-2007 • CSA 2.33a-2007
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Tempered Glass Specifications
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the
Consumer Product Safety Commission (CPSC). The
tempered glass has been tested and certified to the requirements of ANSI Z97.1 and CPSC 16 CFR 1202
(Safety Glazing Certification Council SGCC# 1595 and
1597. Architectural Testing, Inc. Reports 02-31919.01 and
02-31917.01).
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
US
(0-2000 FT)
37,000
26,000
32
CANADA
(2000-4500 FT)
34,500
23,900
33
Models
(U.S. or Canada)
ST-36TRB-IPI
PIER-36TRB-IPI
LCOR-36TRB-IPI
RCOR-36TRB-IPI
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper orifice
size.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials
are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750 ºC shall be considered
non-combustible materials.
F. Combustible Materials Specification
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
G. Electrical Codes
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when it is
installed in locations such as in bathrooms or near sinks.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
7
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
8
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
2
Operating Instructions
User Guide
• Keep remote controls out of reach of children.
A. Gas Fireplace Safety
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
WARNING
• Teach children to NEVER touch the fireplace.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
• Consider not using the fireplace when children will be
present.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacations, trips, etc):
• Remove batteries from remote controls.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Turn off wall controls.
• Unplug 3 volt adapter plug and remove batteries on IPI
models.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
• Turn off gas controls valve on standing pilot models.
When lighting the pilot light on fireplaces with a standing
pilot, remove the fixed glass assembly so you can detect presence of residual gas build-up. See Standing Pilot
Lighting instructions and Maintenance Tasks.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precautions are recommended:
B. Your Fireplace
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
• Install a physical barrier such as:
- A decorative firescreen.
- Adjustable safety gate.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.E.
FIXED GLASS ASSEMBLY
SECTION 14.G.
MANTEL
HEARTH
CLEAR SPACE
SECTION 2.D.
Figure 2.1 General Operating Parts
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
9
C. Blower Kit (optional)
If desired, a blower kit may be added. Contact your dealer to order the correct fan kit.
Blower Installation
1. Install and wire the blower in appliance as shown in
Figure 2.2.
2. Wire the blower temperature sensor and adjustable
speed control (rheostat) according to the instructions
provided with the fan.
3. If rheostat is required, bend rheostat attachment tab
located in bottom of fireplace upward as shown in
Figure 2.3.
3F
4. Attach rheostat to the rheostat attachment tab.
T.
IN CLE
FR AR
ON S
T O PAC
FF E
IR
EP
LA
CE
Figure 2.4 Clear Space
THREADED STUD USED TO
INSTALL TEMPERATURE SENSOR
FAN
Figure 2.2 Blower Location
F. Fixed Glass Assembly
See Section 14.G.
G. Remote Controls, Wall Controls and Wall
Switches
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
RHEOSTAT ATTACHMENT TAB
Figure 2.3 Rheostat Attachment Tab Location
D. Clear Space
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.4.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
E. Decorative Doors and Fronts
• Keep remote controls out of reach of children.
See your dealer if you have questions.
H. Before Lighting Fireplace
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/or
other decorative materials.
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
• Check the wiring.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
• Ensure that there are no gas leaks.
• Check the air shutter adjustment.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
For more information refer to the instructions supplied with
your decorative door or front.
10
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
I. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS (IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burner. DO NOT try to light the burner by
hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• If you cannot reach your gas supplier, call the fire department.
Equipped with wall switch: Turn ON/OFF switch
to ON.
WARNING:
CAUTION:
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240
VAC) TO THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could
expose you to substances in fuel or
fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
2. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this label. If you do not smell gas, go to next step.
3. To light the burner:
• DO NOT touch any electric switch; do
not use any phone in your building.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
GAS
VALVE
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
Equipped with remote or wall control: Press
ON or FLAME button.
Equipped with thermostat: Set temperature to
desired setting.
4. If the appliance does not light after three tries,
call your service technician or gas supplier.
TO TURN OFF
GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch
to OFF.
Equipped with remote or wall control: Press
OFF button.
Equipped with thermostat: Set temperature to
lowest setting.
2. Service technician should turn off electric
power to the control when performing service.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
593-913G
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
11
J. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.G.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fireplace.
NOTICE! Open windows for air circulation during fireplace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
K. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the fireplace warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the fireplace is allowed to burn for 20 to 40 minutes.
Odor from fireplace
When first operated, this fireplace may release an odor for the first several hours. This is
caused by the curing of materials from manufacturing. Odor may also be released from finishing materials and adhesives used near the fireplace. These circumstances may require additional curing related to the installation environment.
Film on the glass
Metallic noise
12
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the fireplace.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
3
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Doors, Surrounds, Fronts
Frequency: Annually
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend annual service by a qualified service technician.
By: Homeowner
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
Glass Cleaning
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
Remote Control
Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote control instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
Frequency: Seasonally
• Place batteries as needed in remote transmitters and
battery-powered receivers.
By: Homeowner
• Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Remove batteries from remote controls.
• Unplug 3 volt adapter plug on IPI models.
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.
• Remove door or decorative front from fireplace and set
aside on work surface.
• See Section 14.G for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
13
Venting
Logs
Frequency: Seasonally
Frequency: Annually
By: Homeowner
By: Qualified Service Technician
Tools needed: Protective gloves and safety glasses.
Tools needed: Protective gloves.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Inspect for damaged or missing logs. Replace as necessary.
Refer to Section 14 for log placement instructions.
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See
Section 6.
• Inspect for corrosion or separation.
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
B. Maintenance Tasks-Qualified Service
Technician
The following tasks must be performed by a qualified service technician.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
Firebox
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace fireplace if firebox has been perforated.
Control Compartment and Firebox Top
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
14
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Replace ember materials with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 14 for proper ember placement.
• Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or
leaking.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Inspect IPI flame-sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.
• Verify that there is not a short in flame sense circuit
by checking continuity between pilot hood and flamesensing rod. Replace pilot as necessary.
Figure 3.1 IPI Pilot Flame Patterns
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
15
4
Getting Started
Installer Guide
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
HORIZONTAL
TERMINATION CAP
(SECTION 10.M)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.D)
VERTICAL TERMINATION CAP
(SECTION 10.E)
STORM COLLAR
(SECTION 10.H)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.D)
ATTIC INSULATION SHIELD (NOT
SHOWN) MUST BE USED HERE
TO KEEP INSULATION AWAY
FROM VENT PIPE IF ATTIC IS
INSULATED (SECTION 8.E)
VENT PIPE (SECTION 9 and 10)
FRAMING/HEADER
(SECTION 5.B)
FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
OPTIONAL
WALL SWITCH
GAS LINE
(SECTION 11.C)
Note: Dual venting configurations
ARE NOT allowed. Appliance MUST
be vented EITHER vertically OR
horizontally.
HEARTH EXTENSION
SURROUND
MANTEL AND
MANTEL LEG
(SECTION 5.D)
Figure 4.1 Typical System
16
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
Before installing, determine the following:
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Non-corrosive leak check solution
Hammer
Phillips screwdriver
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Manometer
Flat blade screwdriver
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
One 1/4 in. female connection (for optional fan).
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
17
5
Framing and Clearances
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
NOTICE: This See-Through appliance is NOT designed 
or approved for an indoor/outdoor application.
36 in.
914 mm
36 in.
914 mm
LCOR
36 in.
914 mm
PIER
36 in.
914 mm
36 in.
914 mm
36 in.
914 mm
36 in.
914 mm
ST
36 in.
914 mm
36 in.
914 mm
RCOR
Figure 5.1 Appliance Locations
18
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk
with a minimum of 300ºF continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being
installed on a cement surface, a layer of plywood may be
placed underneath to prevent conducting cold up into the
room.
B. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
To further prevent drafts, the wall shield and ceiling firestops should be caulked with caulk with a minimum of
• Failure to maintain airspace may cause overheating and
a fire.
A
E
I
F
C
B
G
D
H
A
B
DVP Pipe SLP Pipe
ST-36TRB-IPI
C
D
E
F
G
H
I
DVP Pipe*
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Clearance Combustible Combustible Ends of
Sides of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance
(Width)
Rough
Opening
(Width)
Rough
Opening
(Width)
Inches
10
8-5/8
38-1/8
23
43
31-5/8
0
0
1/2
36
Millimeters
254
219
968
584
1092
803
0
0
13
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
Figure 5.2 Clearances to Combustibles ST-36TRB-IPI
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
19
A
E
I
I
H
C
B
G
D
F
A
B
DVP Pipe SLP Pipe
PIER-36TRB-IPI
C
D
E
F
G
H
I
DVP Pipe*
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Clearance Combustible Combustible Ends of
Sides of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance
(Width)
Rough
Opening
(Width)
Rough
Opening
(Width)
Inches
10
8-5/8
38-1/8
23
40
31-5/8
0
0
1/2
36
Millimeters
254
219
968
584
1016
803
0
0
13
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
Figure 5.3 Clearances to Combustibles PIER-36TRB-IPI
E
A
I
I
H
H
C
B
G
D
F
A
RCOR-36TRB-IPI
LCOR-36TRB-IPI
B
DVP Pipe SLP Pipe
C
D
E
F
G
H
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Clearance Combustible Combustible Ends of
Sides of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance
(Width)
Rough
Opening
(Width)
Rough
Opening
(Width)
Inches
10
8-5/8
38-1/8
24
40
31-5/8
0
0
1/2
36
Millimeters
254
219
968
610
1016
803
0
0
13
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
Figure 5.4 Clearances to Combustibles LCOR-36TRB-IPI and RCOR-36TRB-IPI
20
I
DVP Pipe*
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
See-Through Non-Combustible Mantel
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).
TO CEILING
Note: All
measurements
in inches.
MAX.
18
See-Through Combustible Mantel
12
TO CEILING
Note: All
measurements
in inches.
32
11
MAX.
18
MIN.
10
12
12
11
9
10
6
32
9
7
4
19
6
5
8
25
8
3
7
2
18
5
17
4
16
3
1
6
15
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
MIN.
14
13
Figure 5.7 Minimum Vertical and Maximum Horizontal
Dimensions of Non-Combustibles
12
2-1/2
11
10
5
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
PIER/LCOR/RCOR Non-Combustible Mantel
Figure 5.5 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
TO CEILING
MAX.
PIER/LCOR/RCOR Combustible Mantel
TO CEILING
Note: All
measurements
in inches.
MAX.
12
Note: All
measurements
in inches.
10
18
9
12
11
10
25
8
7
32
8
32
9
12
7
MIN.
19
6
6
18
5
10
17
4
9
16
3
8
15
14
7
MIN.
6
13
12
1
11
10
4
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
5
Figure 5.8 Minimum Vertical and Maximum Horizontal
Dimensions of Non-Combustibles
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
Figure 5.6 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
21
1/2 in.
Min.
TOP VIEW
FIREPLACE
OPENING
2-3/4
in. Min.
1 in.
Max.
Unlimited
3-1/4 in. Min.
Note: Clearance from opening to perpendicular wall.
Figure 5.9 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
SHEETROCK
3.5 in.
= AIR SPACE REQUIRED
Figure 5.10 Non-Combustible Zone (PIER and ST)
SHEETROCK
3.5 in.
= AIR SPACE REQUIRED
Figure 5.11 Non-Combustible Zone (LCOR and RCOR)
22
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
6
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
Gas, Wood or Fuel Oil
Termination Cap
B
A*
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Gas
Termination
Cap **
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
*
X
12
**
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
23
O
N
P
R
F
C
V
Q
B
J
H or i
B
V
D
B
V
V
V
H
V
X
G
M
V
A
V
E
H
V
V
V
L
A
V
V = VENT TERMINAL
X = AIR SUPPLY INLET
K
B
C
= 9 inches...................clearance to outside corner
E
= 6 inches...................clearance to inside corner
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
N
O
L
= 12 inches................clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
M
= 18 inches ....................clearance under veranda, porch, deck,
balcony or overhang
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor.
Figure 6.3 Minimum Clearances for Termination
24
= 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
P
= 3 ft. (Canada) ..........not to be installed above a gas meter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
G = 3 ft ...........................clearance to gas service regulator
vent outlet
H
= 9 inches (U.S.A)
12 inches (Canada). clearance to non-mechanical (unpowered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.
J
= 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
= 6 inches.................clearance from sides of electrical
service
= 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
F
K
V
V
= 12 inches.................clearances above grade, veranda,
porch, deck or balcony
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
= 18 inches.................clearance below unventilated soffit
18 inches.................clearance below ventilated soffit
30 inches .................clearance below vinyl soffits and
electrical service
D
K
C
= AREA WHERE TERMINAL IS NOT PERMITTED
A
Electrical
Service
= 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
Measure vertical clearances from this surface.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
•
Local codes or regulations may require different
clearances.
•
Vent system termination is NOT permitted in screened
porches.
•
Vent system termination is permitted in porch areas with
two or more sides open.
•
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are suggested for use with vinyl siding.
•
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
7
Vent Information and Diagrams
A. Approved Pipe
DO NOT mix pipe, fittings or joining methods from different manufacturers.
Vertical
12
in
.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
8-1/2 in.
B. Vent Table Key
Horizontal
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
8-1/2 in.
This appliance is approved for use with Hearth & Home
Technologies a DVP or SLP venting system. Refer to
Section 16.B for vent component information.
Figure 7.1
Description
V1
First section (closest to appliance) of vertical length
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Subsequent sections of horizontal length
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
D. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
6.3).
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
Pipe
Effective Length
Inches
Millimeters
4
102
DVP4
Effective
Height/Length
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
Figure 7.2 DVP Pipe Effective Length
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
25
E. Vent Diagrams
To replace the first starter elbow with two 45° elbows,
refer to Figure 7.3. All other 90° elbows can be replaced
with two 45° elbows.
General Rules:
• A maximum of three 90° elbows (or six 45° elbows) may
be used in any vent configuration. Some elbows may be
installed horizontally. See Figure 7.6.
• Elbows may be placed back to back anywhere in the
system as long as the first 90° elbow is a starter elbow
except as shown in Figure 7.3.
• When penetrating a combustible wall, a wall shield
firestop must be installed.
Note: The Multi-Sided series fireplaces can adapt
to SLP series vent pipe, if desired.
When venting off the top of the unit, attach a DVP-2SL adapter to
the appliance starting collar, immediately followed by a minimum
48 inch vertical section of SLP series vent pipe.
After the 48 inch vertical section, the venting table rules
must be followed. The first 48 inch vertical section is NOT
counted as part of the vertical components in the table. It is
still counted as part of the overall maximum run. All venting
table rules for the vent run must still be followed.
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal
SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal
• When penetrating a combustible ceiling, a ceiling firestop
must be installed.
• Horizontal runs of vent do not require vertical rise;
horizontal runs may be level.
Top Vent—Horizontal Termination—Two 45° Elbows
Installation requirements to replace the first 90° elbow with two 45° elbows:
Note: Reference Figure 7.14 for
special instructions for use of 45º
elbow on rear vent appliances.
4 ft min.
(1.22 m)
16 ft max.
(4.87 m)
Figure 7.3
26
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
1. Top Vent - Horizontal Termination - (continued)
V1 Minimum
One Elbow
Elbow only
V1
H1
H1 Maximum
1-1/2 ft.
457 mm
6 in.
152 mm
2-1/2 ft.
610 mm
1 ft.
305 mm
3 ft.
914 mm
2 ft.
610 mm
6 ft
1.8 m
3 ft.
914 mm
9 ft.
2.7 m
4 ft.
1.2 m
12 ft.
3.7 m
5 ft.
1.5 m
15 ft.
4.6 m
6 ft.
1.8 m
18 ft.
5.5 m
V1 + H1 = 50 ft. (15.2 m) Maximum
H1 = 18 ft. (5.5 m) Maximum
Figure 7.4
V1 Minimum
Two Elbows
Elbow only
H1 + H2 Maximum
6 in.
152 mm
1 ft.
305 mm
2 ft.
610 mm
2 ft.
610 mm
4 ft.
1.2 m
3 ft.
914 mm
9 ft.
2.7 m
4 ft
1.2 m
12 ft.
3.7 m
5 ft.
1.5 m
15 ft.
4.6 m
6 ft.
1.8 m
18 ft.
5.5 m
V1 + H1 + H2 = 50 ft. (15.2 m) Maximum
H1 + H2 = 18 ft. (5.5 m) Maximum
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 7.5
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
27
1. Top Vent - Horizontal Termination - (continued)
Three Elbows
V1 Minimum
H1 Maximum
Elbow only
V2 Minimum
H2 Maximum
V1 + V2 Minimum
H1 + H2 Maximum
1 ft.
305 mm
6 in.
152 mm
1 ft.
305 mm
6 in.
152 mm
1 ft.
305 mm
6 in.
152 mm
3 ft.
914 mm
6 in.
152 mm
2 ft.
610 mm
1 ft.
305 mm
3 ft.
914 mm
1 ft.
305 mm
6 ft
1.8 m
1 ft.
305 mm
6 ft
1.8 m
2 ft.
610 mm
12 ft.
3.7 m
2 ft.
610 mm
10 ft.*
3m
2 ft.
610 mm
10 ft.*
3m
4 ft
1.2 m
18 ft.
5.5 m
1.8 m
18 ft
5.5 m
3 ft.
914 mm
12 ft.*
3.7 m
3 ft.
914 mm
*H1 + H2 = 18 ft. (5.5 m) Maximum
12 ft.*
3.7 m
6 ft
V1 + V2 + H1 + H2 = 50 ft. (15.2 m) Maximum
H2
V2
V1
H1
Figure 7.6
28
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
2. Top Vent - Vertical Termination
No Elbow
V1 = 60 ft. Max. (18.3 m)
V1 = 3 ft. Min. (914 mm)
Exhaust restrictor Instructions
1. Remove refractory panel and exhaust baffle from pilot
side of appliance. To remove the refractory panel use
a 1/4 inch nut driver and remove the two screws that
secure it in place. To remove the exhaust baffle, remove
the three screws securing the refractory panel in place.
See Figure 7.8.
NOTE: If installing a vertical vent/
termination off the top of the appliance, the optional vertical termination baffle should be used.
Refractory Panel
To access the
exhaust opening,
remove the refractory
panel and exhaust baffle.
To remove refractory
panel, remove the two
screws on top. To remove
the exhaust baffle, remove
the three screws securing it.
V1
Top Vent Application
Exhaust restrictor
Note: Be sure to reinstall the exhaust
b a f f l e a n d refractory
panel after exhaust
restrictor installation.
Figure 7.7
Exhaust restrictors are recommended for these vertically terminated products which have excessive draft.
Exhaust restrictors will compensate for high draft, and
restore visual flame height. If the vent configuration has
a total vertical of 15-60 feet, an exhaust restrictor may
be needed. The exhaust restrictor can be located in the
appliance manual bag.
Rear Vent Application
Exhaust restrictor
Note: Be sure to reinstall the e x h a u s t
baffle and refractory
panel after exhaust
restrictor installation.
Figure 7.8
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
29
2. Break the exhaust restrictor into two pieces. Do this
by bending the part back and forth until it breaks (see
Figure 7.9).
4. Center the exhaust restrictor in the open end of the
exhaust outlet and secure through the slots on the
exhaust restrictor with the 2-1/4 in. self tapping screws
provided in the appliance manual bag.
5. Reinstall the exhaust baffle and the refractory panel.
1
2
3
4 5
BREAK
HERE
SETTINGS
Figure 7.9 Exhaust Restrictor
1
3. Match the amount of vertical you have in the system
with the chart to find the appropriate position to set the
exhaust restrictor (see Figure 7.10).
TOP VENT
2
3
4 5
Figure 7.10
REAR VENT
Vertical
NG
LP
NG
LP
4 ft.
1-1
No
Restrictor
No
Restrictor
8 ft.
2-2
1-2
1-1
No
Restrictor
No
Restrictor
15 ft.
3-3
3-2
2-2
1-2
20 ft.
3-4
3-3
3-3
2-3
25 ft.
3-4
3-3
3-3
2-3
30 ft.
4-4
3-4
3-4
3-3
35 ft.
4-4
3-4
3-4
3-3
40 ft.
5-4
4-4
4-4
3-4
45 ft.
5-4
4-4
4-4
3-4
50 ft.
5-5
5-4
5-4
4-4
55 ft.
5-5
5-4
5-4
4-4
Note: If the DVP-2SL adapter and SLP pipe is used, you
MUST subtract one number from the table above.
Example: Top vent 40 ft vertical with DVP pipe = 5-4
Top vent 40 ft vertical with SLP pipe = 4-3
30
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Two Elbows
V1
H1 Maximum
One Elbow
V2
V1 + V2 Minimum
2-1/2 ft.
762 mm
*
*
*
2 ft.
607 mm
6 ft.
1.8 m
*
*
*
4 ft.
1.2 m
12 ft.
3.7 m
*
*
*
6 ft.
1.8 m
18 ft.
5.5 m
*
*
*
V1 + V2 + H1 = 50 ft (15.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)
V2
V1
H1
Figure 7.11
V1
Three Elbows
V2
H1+ H2
V2
V1 + V2 Minimum
H1+ H2 Maximum
ELBOW ONLY
1 ft.
305 mm
*
*
*
1 ft.
305 mm
1 ft.
305 mm
2 ft.
610 mm
*
*
*
2 ft.
610 mm
2 ft.
610 mm
4 ft
1.2 m
*
*
*
4 ft
1.2 m
3 ft.
914 mm
9 ft.
2.7 m
*
*
*
9 ft.
2.7 m
4 ft
1.2 m
12 ft.
3.7 m
*
*
*
12 ft.
3.7 m
6 ft.
1.8 m
18 ft.
5.5 m
*
*
*
18 ft.
5.5 m
H1+ H2 = 18 ft (5.5 m) Maximum
*No specific restrictions on this value EXCEPT
V1+ V2 + H1+ H2 cannot exceed 50 ft (15.2 m)
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.12
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
31
3. Rear Vent - Horizontal Termination
H1 = 16 in. (406 mm) Maximum
No Elbow
H1
Figure 7.13
One 45° Elbow
DO NOT use a 45º elbow
in corner installations. Use
two 90º elbow instead.
H1
Figure 7.14
32
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
3. Rear Vent - Horizontal Termination - (continued)
H1 Maximum
Two Elbows
V1 Minimum
H2 Maximum
H1+ H2 Maximum
1 ft.
305 mm
6 in.
152 mm
1 ft.
305 mm
1 ft
305 mm
2 ft.
610 mm
1 ft.
305 mm
2 ft.
610 mm
3 ft.
914 mm
3 ft.
914 mm
2 ft.
610 mm
4 ft
1.2 m
6 ft.
1.8 m
3 ft.
914 mm
3 ft.
914 mm
7 ft.
2.1 m
9 ft.
2.7 m
3 ft.
914 mm
4 ft.
1.2 m
10 ft.
3m
12 ft.
3.7 m
3 ft.
914 mm
5 ft.
1.5 m
12 ft.
3.7 m
15 ft.
4.6 m
3 ft.
914 mm
6 ft.
1.8 m
15 ft.
4.6 m
18 ft.
5.5 m
V1+ H1+ H2= 50 ft (15.2 m) Maximum H1= 3 ft (914 mm) Maximum
*H1+ H2= 18 ft (5.5 m) Maximum
V1
H2
H1
Figure 7.15
H1 Maximum
Three Elbows
INSTALLED
HORIZONTALLY
H3
V1 Minimum
H2+ H3
H1+ H2+ H3 Maximum
6 in.
152 mm
6 in.
152 mm
6 in.
152 mm
1 ft.
305 mm
1 ft.
305 mm
1 ft.
305 mm
2 ft.
610 mm
3 ft.
914 mm
3 ft.
914 mm
2 ft.
610 mm
3 ft.
914 mm
6 ft.
1.8 m
3 ft.
914 mm
3 ft.
914 mm
6 ft.
1.8 m
9 ft.
2.7 m
3 ft.
914 mm
4 ft.
1.2 m
9 ft.
2.7 m
12 ft.
3.7 m
V1+ H1+ H2+ H3= 40 ft (12.2 m) Maximum
H1= 3 ft (94 mm) Maximum
H1+ H2+ H3= 12 ft (3.7 m) Maximum
H2
V1
H1
Figure 7.16
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
33
4. Rear Vent - Vertical Termination
V1 Minimum
One Elbow
H1 Maximum
1 ft.
305 mm
3 ft.
914 mm
2 ft.
610 mm
5 ft.
1.5 m
3 ft.
914 mm
7 ft.
2.1 m
4 ft.
1.2 m
8 ft
2.4 m
5 ft.
1.5 m
8 ft
2.4 m
V1+ H1 = 40 ft (12.2 m) Maximum
V1
H1
Figure 7.17
V1 Minimum
Two Elbows
Back to Back 90° Elbows
H1 + H2 Maximum
3 ft.
914 mm
2 ft
610 mm
6 ft.
1.8 m
4 ft.
1.2 m
9 ft.
2.7 m
5 ft.
1.5 m
10 ft.
3m
6 ft.
1.8 m
12 ft.
3.7 m
V1+ H1 + H2= 50 ft (15.2 m) Maximum
H1+ H2= 16 ft (4.9 m) Maximum
V2
INSTALLED
HORIZONTALLY
H2
H1
Figure 7.18
34
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
4. Rear Vent - Vertical Termination - (continued)
H1 Maximum
Three Elbows
V2
V1 Minimum
H2
H1+ H2 Maximum
1 ft.
305 mm
1 ft.
305 mm
1 ft.
305 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
3 ft.
914 mm
5 ft.
1.5 m
4 ft.
1.2 m
3 ft.
914 mm
4 ft.
1.2 m
8 ft.
4.6 m
5 ft.
1.5 m
4 ft.
1.2 m
6 ft.
1.8 m
11 ft.
3.4 m
6 ft.
1.8 m
5 ft.
1.5 m
8 ft.
2.4 m
14 ft.
4.3 m
2.4 m
6 ft.
1.8 m
9 ft.
2.7 m
17 ft.
5.2 m
8 ft.
H1 = 8 ft (2.4 m) Max. V1+ V2+ H1+ H2= 50 ft (15.2 m) Max.
H1+ H2= 17 ft (5.2 m) Max.
H2
V1
Figure 7.19
H1
Three Elbows
V1
H1
H2
H3
V1 Minimum
H1+ H2+ H3 Maximum
*
*
*
8 ft.
2.4 m
4 ft.
1.2 m
*
*
*
9 ft.
2.7 m
5 ft.
1.5 m
*
*
*
10 ft.
3.1 m
6 ft.
1.8 m
*No specific restrictions on this value EXCEPT
V1+ H1+ H2+ H3 cannot exceed 50 ft. (15.2 m) Maximum
H1+ H2+ H3 = 6 ft. (1.8 m) Maximum
H3
H2
Figure 7.20
H1
INSTALLED
HORIZONTALLY
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
35
8
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
B. Continue Adding Vent Components
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
WARNING! Risk of Fire! Installation of this appliance
may require the use of heat shield 385-920 above the
first 900 elbow in the venting system.
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
• The heat shield is required above the first elbow if the
clearance to combustible surface above is between
three (3) and four (4) inches. A shield is not required for
clearances greater than four inches. See Figure 8.2.
COMBUSTIBLE
SURFACE
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
‡ DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
‡ ,f wall thickness is less than 4 in. the e[isting heat shields must be field trimmed. ,f
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
‡ SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
‡ ,f wall thickness is less than 4-3/8 the e[isting heat shields must be field trimmed.
,f wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
HEAT
SHIELD
(Required for clearances
between 3 and 4 inches.)
3 in. MIN.
(76 mm)
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
WALL
Figure 8.2
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
Wall
Shield
Firestop
1 in. (25 mm)
clearance
bottom & sides
• Fasten the shield in place using the four pilot holes
provided in the part. The shield should be oriented such
that the 13-1/8 inch dimension (longest dimension) is
running in the same direction the elbow is pointing. The
shield should be centered directly above the elbow, and
positioned so that it creates a 1/2 inch airspace between
the shield and the combustible surface. See Figure 8.3.
WALL
* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at wall shield firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
36
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
COMBUSTIBLE SURFACE
CORRECT
INCORRECT
C. Wall Penetration Framing
Combustible Wall Penetration
DIRECTION
UP
HEAT SHIELD
90º ELBOW
Figure 8.3
• If the combustible materials are not in place at the
time of install the elbow heat shield may be screwed
to the exhaust pipe (see Figure 8.4). Cut the tabs as
shown and bend down. Secure the heat shield to the
pipe maintaining 3 inch to 4 inch between the pipe and
shield.
SCREW
3 in.
(76 mm)
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B)
attached to them.
• See Section 10.M for information for regarding the installation of a horizontal termination cap.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
Figure 8.4
10 in.
12 in.
C
D
10 in.
A*
12 in.
B*
A*
43-3/4 in.
B*
28 in.
C
42-3/4 in.
D
27 in.
* Shows center of vent framing hole for top or rear venting. The center of the
hole is one (1) inch (25.4 mm) above the center of the horizontal vent pipe.
Figure 8.5 Wall Penetration
Note: When terminating horizontally off the top of the unit
using SLP pipe, a 10 in. x 10 in. framing hole is required.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
37
D. Vertical Penetration Framing
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 8.6).
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 8.6).
ATTIC ABOVE
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.7.
A
• Secure with three fasteners on each side.
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
PIPE
A
DVP
10 in. (254 mm)
SLP
9 in. (229 mm)
Figure 8.6
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
INSTALLED BELOW CEILING
CEILING FIRESTOP
INSTALLED ABOVE CEILING
Figure 8.7 Installing the Attic Shield
38
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
E. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies requires the use of an attic shield.
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be secured in place.
Flat Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
INSERT 3
SCREWS
BEND 3 TABS
OUTWARD TO
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
CLEARANCE
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
Figure 8.8 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) to fit your ceiling pitch. Snip cut edge to recreate
1 in. bend tabs all the way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
39
9
Appliance Preparation
A. Top Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
NOTICE: Once the vent cap has been removed it CANNOT
be reattached.
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
Figure 9.3 Fold the center parts of the retaining band up
and use to remove the vent cap.
Figure 9.1 Remove the elbow heat shield by removing
the four screws holding it to the top of the appliance. Refer to Section 6B to determine if the elbow heat shield is
required.
Figure 9.4 Remove and discard the seal cap, insulation
donut, insulation plug, and the insulation basket. Attach the
first vent section (it will snap into place). Slide the vent
gasket onto the vent section and then, up against the appliance. Secure the vent gasket to the appliance with two
self-tapping screws found in the manual bag. Note: The
vent gasket can found in the manual bag.
Figure 9.2 Cut the metal retaining band and fold the sides
out.
40
Proceed to Section 9. C.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
B. Rear Vent
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
NOTICE: Once the vent cap has been removed it CANNOT
be reattached.
Figure 9.7 Discard the seal cap, insulation plug and the
insulation basket.
Figure 9.5 Cut the metal retaining band.
Figure 9.6 Remove the seal cap.
Figure 9.8 Attach the first vent section (it will snap into
place). Slide the vent gasket onto the vent section and then,
up against the appliance. Secure the vent gasket to the
appliance with two self-tapping screws found in the manual
bag. Note: The vent gasket can found in the manual bag.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
41
C. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
6. Bend out nailing tabs on each side making sure to keep
the nailing tabs flush with the framing.
7. Using a framing square, make sure that the sides of
the appliance are square to the bottom as shown in
Figure 9.10.
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
NOTICE: Failure to ensure that the fireplace opening
is square may result in the decorative front not fitting
properly.
The diagram shows how to properly position, level, and
secure the appliance (see Figure 9.9). Nailing tabs are provided to secure the appliance to the framing members.
1. Venting - refer to Vent Clearances and Framing (Section
8) for hole location.
2. When installing a LCOR or RCOR fireplace remove
the nailing tab located on the side of the unit and
reattach it to the front corner of the unit as shown in
Figure 9.9 (R-COR).
90º
SID
ET
O
SID
E
CK
TO
NT
BA
O
FR
Figure 9.10 Proper Positioning and Leveling of an Appliance
8. Secure the appliance to the framing by using nails
or screws through the nailing tabs. It is acceptable to
use plumber strap to secure the unit to the framing if
necessary. See Figure 9.11. Be sure to maintain all
clearances to combustible material.
Figure 9.9 Attach Nailing Tab to Front Corner of Unit
3. Place the appliance into position, making sure to
maintain proper clearance to combustibles.
4. Level the appliance from side to side and front to back. It
is acceptable to use wood shims under the appliance.
5. Fasten the appliance to the floor using the pilot holes
located at the bottom of the appliance.
42
NAILING TABS
Figure 9.11 Securing An Appliance
Note: Once appliance is setup for top or rear venting, it
CANNOT be changed at a later time.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
10
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with silicone with a
minimum of 300ºF continuous exposure rating, including
the slip section that connects directly to the horizontal termination cap.
Figure 10.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections (DVP Pipe Only)
Per Figure 10.2:
B
Figure 10.3
Figure 10.2
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 10.4 Seams
INCORRECT
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
43
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.6.
• Attach a DVP-2SL adapter to the starting collar of the
appliance.
• Slide together to the desired length.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
Caulk with a minimum of 300ºF continuous exposure
rating may be used to hold the part in place.
Pilot hole
• Continue adding vent components, locking each
succeeding component into place.
Figure 10.6 Slip Section Pilot Holes
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.7.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature silicone,
including the slip section that connects directly to the horizontal termination cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 10.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature silicone sealant.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 10.5 Adding Venting Components
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
44
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13

D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs originating off the top of the appliance, with
no offsets, must be supported every 8 ft. (2.44 m) after
the maximum allowed 25 ft. (7.62 m) of unsupported rise.
• Rotate either section (see Figure 10.10) so the seams
on both pipe sections are aligned as shown in Figure
10.11.
• Vertical runs originating off the rear of the appliance, or
after any elbow, must be supported every 8 ft. (2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal runs must be supported every 5 feet (1.52
m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 10.8
and 10.9.
• Wall shield firestops may be used to provide horizontal
support to vent sections.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 10.10 Rotate Seams for Disassembly
120º
Figure 10.8 Securing Vertical Pipe Sections
Figure 10.11 Align and Disassemble Vent Sections
120º
Figure 10.9 Securing Horizontal Pipe Sections
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
45
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
silicone with a minimum of 300ºF continuous exposure
rating to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 10.12
• Remove shingles or other roof covering as necessary
to cut the rectangular hole for the support box. Cut the
hole 1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
10.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
46
Figure 10.13
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
G. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.15
GAS DIRECT VENT
TERMINATION CAP
H. Assemble and Install Storm Collar
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................. 2.5
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
• Connect both halves of the storm collar with two screws
(see Figure 10.16).
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 10.17).
• Caulk around the top of the storm collar (see Figure 10.18).
* 3 foot minimum in snow regions
Figure 10.14 Minimum Height From Roof To Lowest Discharge
Opening
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
Figure 10.16 Assembling the Storm Collar
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.15.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Figure 10.17 Assembling the Storm Collar Around the Pipe
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
47
I. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 10.18).
TERMINATION CAP
K. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.20).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.20.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
STORM
COLLAR
SCREWS
CAULK
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 10.18
J. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the wall shield firestop.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
10.19.
Figure 10.19 Wall Thimble
48
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
L. Install Horizontal Termination Cap (DVP
and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 10.20 Venting through the wall
Cap Specification Chart
(depth without using additional pipe sections)
36 inch
Multisided
Series
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Rear Vent
Top Vent
Rear Vent
Depth
Depth
Depth
Depth
2-7/8 in to
3-1/8 in.
5-1/4 in. to
5-1/2 in. to
4-3/4 in
to 5 in.
9-1/4 in.
9-1/2 in.
DVP-HPC1
Top Vent
Depth
2-7/8 in.
to 5 in.
DVP-HPC1
Rear Vent
Depth
3-1/8 in.
5-1/4 in.
DVP-HPC2
Top Vent
Depth
5 in. to
9-1/8 in.
DVP-HPC2
Rear Vent
Depth
5-1/4 in. to
9-1/2 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
49
11
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• The gap between supply piping and gas access hole
may be caulked with caulk with a minimum of 300ºF
continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air
infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
• Pressure requirements are:
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Maximum inlet pressure
14.0 in. w.c.
14.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
Gas Pressure
WARNING! Risk of Fire/Explosion! High pressure will
damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 inch
(13 mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
50
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In the CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
12
Electrical Information
A. Wiring Requirements
C. Optional Accessories Requirements
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• Wire the appliance junction box to 110-120 VAC. This is
required for proper operation of the appliance.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
D. Electrical Service and Repair
• A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection,
in compliance with the applicable electrical codes,
when it is installed in locations such as in bathrooms
or near sinks.
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
 • Low voltage and 110-120 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
B. Intellifire Ignition System Wiring
 • Wire the appliance junction box to 110-120 VAC for
proper operation of the appliance.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figures 12.1 and 12.2, Intellifire Pilot Ignition
(IPI) Wiring Diagram.
• This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
• Plug the 3-volt AC transformer into the appliance junction
box to supply power to the unit OR install two D cell
batteries (not included) into the battery pack before use.
NOTICE: Batteries should not be placed in the battery
pack while using the transformer. Remove batteries before
using the transformer, and unplug the transformer before
installing the batteries. Battery polarity must be correct or
module damage will occur.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
51
INTERMITTENT
PILOT IGNITOR
IGNITION
MODULE 3 VAC
I
S
TRANSFORMER
3 VAC
ORANGE
NEUTRAL
HOT
WHITE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
WIRES
(TO BROWN)
GREEN
ORANGE
BATTERY PACK
WIRE ASSEMBLY
VALVE
Figure 12.1 Intellifire Ignition Wiring Diagram with Wall Switch or Thermostat
IGNITION
MODULE 3 VAC
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 110-120 VAC
is required at junction box unless equipped
with battery back-up.

INTERMITTENT
PILOT IGNITOR
I
S
TRANSFORMER
3 VAC
ORANGE
NEUTRAL
HOT
WHITE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
ORANGE
GREEN
WIRES
(TO BROWN)
BATTERY PACK
REMOTE
PLUG IN
VALVE
Figure 12.2 Intellifire Ignition Wiring Diagram with Remote Receiver
52
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
E. Junction Box Installation
The junction box must be wired from the INSIDE of the
appliance:
• Determine which side of the appliance the junction box
is located on.
ROMEX CONNECTORS
• Pull the electrical wires from outside the appliance through
the knockout making sure to use a Romex connector to
fasten the electrical wires to the unit.
• Pull enough wire into the valve compartment to easily reach
the junction box location.
• Remove the screw attaching the junction box to the junction
box bracket and set it aside.
• Route the wire through the knockout in the junction box
bracket.
• Wire the junction box and reattach it to the bracket by
inserting the tab in the slot and attaching with screw
previously removed. Ensure that a Romex connector is
used to attach the electrical wires to the junction box.
NOTICE: DO NOT wire 110-120 VAC to wall switch.

Figure 12.3 Junction Box Detail
F. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted switch for use
with a fan (See Figure 12.4):
• The power can then be supplied from the switch box to
the appliance using a minimum of 14-3 with ground wire.
JUNCTION BOX
• At the switch box connect the black (hot) wire and red
(switch leg) wire to the wall switch as shown.
BLACK
WHITE
GREEN
SWITCH BOX
• At the appliance connect the black (hot), white (neutral)
and green (ground) wires to the junction box as shown.
• Add a 1/4 in. insulated female connector to the red (switch
leg) wire, route it through the knockout in the face of the
junction box, and connect to the top fan switch connector
(1/4 in. male) as shown.
RED
BLACK
WHITE
GREEN
RED
BLACK
WHITE
GREEN
• The power supply for the appliance must be brought into
a switch box.
SWITCH
MINIMUM 14-3 AWG
WITH GROUND
POWER
SUPPLY
WIRES
KNOCKOUT
RED
Figure 12.4 Junction Box Wired to Wall Switch
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
53
13
Finishing
A. Splatter Guard
The splatter guard is a piece of corrugated material
used to protect the appliance during the installation
process before finishing work on the whole hearth is
complete. Splatter guards may be factory installed or
accompany the door of the unit, depending on the fireplace model. Splatter guards must be removed before
appliance is fired.
WARNING! Risk of Fire! Close the ball valve before installing the splatter guard to prevent accidental lighting.
Remove the splatter guard before lighting the appliance.
Step 1. Turn off gas to valve. Red gas shutoff knob is
located on ball valve. Disconnect the 3 volt transformer
from the junction box. See Figure 13.1.
Figure 13.3 Folding of Right and Left Sides of Splatter Guard
Step 4. Center the splatter guard in front of the unit as
shown in Figure 13.3. Place the splatter guard in the unit
by guiding the top flap into proper position and then continuing to guide the tabs on the side flaps into the top slot
on the left and right sides of the appliance. The top slot
is indicated in Figure 13.5 Take care not to bend or break
off the tabs.
Figure 13.1
To install the Splatter Guard:
Step 2. Crease flap on top side of splatter guard using
the scored line as the guide. See Figure 13.2.
Figure 13.4 Installation of Splatter Guard
TOP SLOT
Figure 13.2
Step 3. Crease flaps on left and right sides of splatter guard
using the scored line as the guide. See Figure 13.3.
54
Figure 13.5 Top slot
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Step 5. Fold bottom flap along score line as indicated in
Figure 13.6 and tuck into valve access area of appliance.
Splatter guard should fit securely on front of unit.
Figure 13.9 Securing Tabs Inside Front of Splatter Guard
Figure 13.6 Folding Bottom Flap
Once plumbing and wiring are complete on the fireplace,
the lower access panel may be closed until the time that the
splatter guard must be removed for firing the appliance.
Figure 13.10 Splatter Guard with Lower Access Panel Open
Figure 13.7 Prepare to Open Lower Access Panel
Step 6. To open lower access panel of splatter guard, place
one hand above score line and place two fingers from other
hand in the round holes on the front of the splatter guard.
See Figure 13.7. Pull out and fold up the panel as shown
in Figure 13.8. Disengage the tabs on left and right bottom
of splatter guard and fit them into the square holes. The
tabs are now inside the front of the splatter guard; carefully
bend them down. See Figure 13.9.
To Close the Lower Access Panel:
Carefully disengage the tabs from the square holes and
bend the access panel to its original position. Bend the
center bottom flap and insert it into the bottom of the appliance.
Figure 13.11 Splatter Guard with Lower Access Panel Closed
To Remove the Splatter Guard:
Figure 13.8 Opening Lower Access Panel
Carefully grab splatter guard on or near the vertical center
on the left and right sides. Pull outward gently, but firmly,
taking care not to tear or remove the inserted tabs.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
55
See-Through Mantel Projection
B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply
could cause fire.
TO CEILING
Note: All
measurements
in inches.
MAX.
18
See-Through Mantel Projection
12
TO CEILING
Note: All
measurements
in inches.
32
11
MAX.
18
MIN.
10
12
12
11
9
10
6
32
9
7
4
19
6
5
8
25
8
3
7
2
18
5
17
4
16
3
1
6
15
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
MIN.
14
13
Figure 13.14 Minimum Vertical and Maximum Horizontal
Dimensions of Non-Combustibles
12
2-1/2
11
10
5
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
PIER/LCOR/RCOR Mantel Projection
Figure 13.12 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
TO CEILING
MAX.
PIER/LCOR/RCOR Mantel Projection
TO CEILING
Note: All
measurements
in inches.
MAX.
12
Note: All
measurements
in inches.
10
18
9
12
11
10
25
8
7
32
8
32
9
12
7
MIN.
19
6
6
18
5
10
17
4
9
16
3
8
15
14
7
MIN.
6
13
12
1
11
10
4
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
5
Figure 13.15 Minimum Vertical and Maximum Horizontal
Dimensions of Non-Combustibles
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
Figure 13.13 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
56
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
D. Finishing Material
1/2 in.
Min.
TOP VIEW
FIREPLACE
OPENING
2-3/4
in. Min.
1 in.
Max.
Unlimited
Only doors certified for use with this appliance model may
be used. Contact your dealer for a list of doors that may
be used. Once you have determined what kind of door
and finishing material is going to be used on the fireplace,
you may use the table below which shows the door models and the finishing material thickness allowed. For an
inside fit there is an available template to assist with sizing the finishing material.
ST-36TRB-IPI
3-1/4 in. Min.
Note: Clearance from opening to perpendicular wall.
Figure 13.16 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
DOOR
FIT
Aero
Folio
Inside
Inside
Overlap
Inside
Overlap
Inside
Overlap
Inside
Overlap
Inside
Overlap
Inside
Arcadia
C. Facing Material
• Metal front faces may be covered with non-combustible
materials only.
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers or doors,
or access for service.
• Facing and/or finishing materials must never overhang
into the glass opening.
• Observe all clearances when applying combustible
materials.
• Seal joints between the finished wall and appliance top
and sides using a 300 °F minimum sealant. Refer to
Figure 13.17.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
Halston
Chateau
Valencia
Galleria
FINISH MATERIAL
MAXIMUM
THICKNESS
Any
Any
1 inch
Any
1 inch
1 inch - 2 inch
1 inch
Any
1 inch
Any
1 inch
1 inch - 2 inch
SEE FIGURE
13.18
13.18
13.19
13.20
13.19
13.21
13.19
13.20
13.19
13.20
13.19
13.21
PIER-36TRB-IPI
DOOR
FIT
Aero
Chateau
Arcadia
Inside
Inside
Inside
FINISH MATERIAL
MAXIMUM
THICKNESS
Any
Any
Any
SEE FIGURE
13.22
13.22
13.22
Finish wall material may be
combustible - Top and Sides
0 in.
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
DOOR
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
Stop finishing material flush with opening.
Figure 13.18 Folio Door and Aero
FRONT FACE OF FIREPLACE
0 in.
0 in.
High Temperature Sealant (300° F/149° C min.)
Top and Side Seal Joint
Figure 13.17 Noncombustible Facing Diagram
DOOR
1 in. MAX
FINISHING MATERIAL
(TOP EDGE)
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
Figure 13.19 Overlap Fit Door
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
57
FINISHING
MATERIAL
FINISHING
MATERIAL
FINISHING
MATERIAL
DOOR
37 in.
(Outside door width)
37-1/4 in.
(Includes 1/8 in. opening each side of door)
33-3/4 in.
(Inside door height)
34 in.
33-5/8 in.
37 in.
(Outside door width)
37-1/4 in.
(Includes 1/8 in. opening each side of door)
37-1/4 in.
Finishing materials over 1 inch thick.
Figure 13.22 Pier Door Finishing
Figure 13.20 Inside fit door
FINISHING
MATERIAL
FINISHING
MATERIAL
*IF FINISHING MATERIAL IS THICKER THAN
2 IN., DOORS WILL ONLY OPEN
AS FAR AS PICTURED
DOORS
34 IN.
33-3/4 IN.
37-1/4 IN.
Finishing material between 1 and 2 inches thick.
Figure 13.21 Operable hinge door
58
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
E. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various
dimensions. Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance
will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation
will also have to be added to the following: Extension Wall Hole referenced in Figure 8.2 (Exterior Wall Hole) and Rough
Opening Height (header height) referenced in Figure 5.2. Note: Finished floor thickness should also be considered when
determining installation dimensions.
MODEL
DESCRIPTION
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LAURENT SURROUND
CAMDEN SURROUND
CAMDEN SURROUND W/HEARTH
CAMDEN SURROUND W/MANTEL
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND
ESSEX SURROUND W/HEARTH
ESSEX SURROUND W/MANTEL
ESSEX SURROUND W/MANTEL &
HEARTH
MONROE SURROUND
MONROE SURROUND W/HEARTH
MONROE SURROUND W/MANTEL
MONROE SURROUND W/MANTEL &
HEARTH
ELEVATED APPLIANCE
DIMENSION
See Note 1
0 (See Note 3)
9-1/4 in.
1-1/2 in.
0
1-3/4 in.
0
MARBLE LEG CUT
LENGTH
See Note 2
27-3/8 in.
29-3/8 in.
N/A
N/A
N/A
N/A
CAMM36PGH
1-3/4 in.
N/A
ESSEX36PG
ESSEX36PGH
ESSEXM36PG
0
1-3/4 in.
0
N/A
N/A
N/A
ESSEXM36PGH
1-3/4 in.
N/A
MON36PG
MON36PGH
MONM36PG
0
1-3/4 in.
0
N/A
N/A
N/A
MONM36PGH
1-3/4 in.
N/A
PART #
AFKDMPB
AFKDMPB W/ HTKDMPB
LAURENT-36
CAM36PG
CAM36PGH
CAMM36PG
Note 1. Add dimensions to Exterior Wall Hole (Figure 8.2) and Rough Opening Height (Figure 5.2).
Note 2. Verify Marble Cut Lengths on site prior to cutting.
Note 3. Dimensions assume use of a 3/4 in. Hearth Pad.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
59
14
Appliance Setup
A. Remove Fixed Glass Assembly
E. Lava Rock and Glowing Ember Placement
See Section 14G.
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Placing the Ember Material
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• When placing Glowing Embers® onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces just in front of the port trail,
but not on or in between the ports (see Figure 14.1).
Failure to follow this procedure will likely cause lighting
and sooting problems.
DO NOT PLACE EMBERS
IN THE CIRCLED AREAS
PILOT LOCATED HERE
Figure 14.1 Placement of Embers
• Place Glowing Embers on top of the log attachment
tabs to conceal their location. Ensure that the Glowing
Embers do not obstruct the port trail.
• Place Lava Rock on areas of base pan away from the
burner. Use this material to give the appliance a realistic
ash bed.
• Save the remaining ember materials for use during
appliance servicing. The embers provided should be
enough for 3 to 5 applications.
60
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
F. Install the Log Assembly
Log Set Assembly: LOGS-2128
Models: ST-36TRB-IPI, PIER-36TRB-IPI
ST-36TVB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI
CAUTION: DO NOT reposition logs that have been
factory installed! Follow these instructions to position
the logs that were packaged separately.
2
3
B
1
PILOT
C
D
Figure 1. Log Assembly Location
A
Figure 2. Factory Installed Logs
STEP 1. CAUTION! Logs are fragile! Carefully remove the logs and cardboard tray from the inside of the fireplace.
See Figure 1. Remove the microfoam and inspect the logs for damage. Inspect the four factory installed logs for damage.
Locate the pilot in order to verify your position in relation to the appliance. See Figure 2.
HUMP
1
1
NOTCH
C
A
Figure 3. Placement of Log #1
Figure 4. Placement of Log #1
STEP 2. Log #1 (SRV2128-704): Mate the notch on the end of log # 1 with the hump on top of log A. Set the other
end of Log #1 onto the smooth area on top of Log C.
2128-935
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
61
GRATE TINES
2
1
B
D
Figure 5. Placement of Log #2
2
C
A
Figure 6. Placement of Log #2
STEP 3. Log #2 (SRV2128-705): The Y-shaped end of log #2 should rest on log B and log C. The other end should
come in contact with the second grate tine from the left. Mate the bottom of log # 2 with the notches on top of log B and the
smooth area on top of the end of log C.
GRATE TINES
3
B 3
INDENTATIONS
1
2
D
C
PILOT
A
2
Figure 7. Placement of Log #3
Figure 8. Placement of Log #3
STEP 4. Log #3 (SRV2128-707): The bottom end of log #3 should come in contact with the far left grate tine. Mate
the bottom of log # 3 with the indentations on Log D and the top of Log #2.
62
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
G. Fixed Glass Assembly
H. Install Trim Kits and Surrounds
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
• Install optional trim kits and/or surrounds using the
instructions included with the accessory.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
• Pull the four glass latches out of the grooves on the glass
frame top and bottom.
• Remove the glass door from the appliance.
• Multiple sides may be able to be removed based upon
model.
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance.
• Pull out the four glass latches and place in the grooves
on the glass frame top and bottom.
• Make sure all sides are replaced properly.
• Use non-combustible materials to cover the gap between
the sheet rock and the appliance (when applicable to the
model).
I. Air Shutter Setting
This appliance has an adjustable air shutter (which controls the primary air) factory set for the minimum vertical
vent run (see Figure 12.15). If your installation has more
than the minimum required vertical vent length, adjustment of the air shutter may be necessary to obtain optimal flame appearance. This should be adjusted by a
qualified installer at the time of installation.
By pushing the air shutter handle towards the pilot, you will
be closing the air shutter. To adjust loosen the wing nut.
Care should be taken when adjusting the air shutter so as
not to cause the appliance to soot. If sooting occurs the air
shutter will need to be opened by pushing the handle away
from the pilot. When finished tighten wing nut.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
AIR SHUTTER
OPEN
CLOSED
LATCHES
BOTH BOTTOM
AND TOP)
GLASS
ASSEMBLY
Figure 14.3 Fixed Glass Assembly
Figure 14.4 Air Shutter
Air Shutter Settings
Burner
NG
LP
1/8 in.
Fully open
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
63
15
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you
do experience a problem, this troubleshooting guide will assist a qualified technician in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified technician. Contact your dealer to
arrange a service call by a qualified technician.
A. Intellifire Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
a. Incorrect wiring.
The ignitor/module
makes noise, but no
b. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
64
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify connections are not grounding out to metal
chassis, pilot burner, pilot enclosure, mesh screen if present, or
any other metal object.
c. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
d. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5
mm) away from “I” terminal on module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal
module must be replaced. If there is a spark at “I” terminal, module
is fine. Inspect pilot assembly for shorted sparker wire or cracked
insulator around electrode. Replace pilot if necessary.
a. No power or transformer installed
incorrectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
c. Improper wall switch wiring.
Verify that 110-120 VAC power is “ON” to junction box.
d. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire “I” from module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal
module must be replaced. If there is a spark at “I” terminal, module
is fine. Inspect pilot assembly for shorted sparker wire or cracked
insulator around electrode.
a. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits, inlet pressure must not
exceed 14 in. W.C.
b. Ignitor gap is incorrect.
Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm).
c. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
d. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is below 2.7.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13

Intellifire Ignition System - (continued)
Symptom
4. Pilot lights but continues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
Possible Cause
a. A shorted or loose connection in flame
sensing rod.
Corrective Action
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify
connections are not grounding out to metal chassis, pilot
burner, pilot enclosure or screen if present, or any other
metal object.
b. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is
flame sensing rod.
engulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. Verify correct
pilot orifice is installed and gas inlet is set to pressure
specifications. Polish flame-sensing rod with fine steel wool
to remove any contaminants that may have accumulated on
flame sensing rod.
c. Module is not grounded.
Verify module is securely grounded to metal chassis of
appliance. Verify that wire harness is firmly connected to
the module.
d. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing
rod is not cracked, damaged, or loose. Verify connection
from flame sensing rod to white sensor wire. Polish flamesensing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multimeter with ohms set at lowest range.
Replace pilot if any damage is detected.
e. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at
“I” terminal module must be replaced. If there is a spark at
“I” terminal, module is fine.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
65
16
Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

ØK
L
ELECTRICAL
ACCESS
M
TOP VIEW
ØK
N
C
O
D
J
GAS LINE
ACCESS
F
i
E
A
P
G
B
FRONT VIEW
LEFT VIEW
RIGHT VIEW
Location
Inches
Millimeters
Location
Inches
Millimeters
A
36
914
I
1-1/2
38
B
42-1/2
1080
J
27
686
8
203
305
C
24-1/2
622
K
D
33-1/2
851
L
12
E
1
25
M
9-1/2
241
F
2-1/8
54
N
38
965
G
4-1/8
105
O
34-5/8
880
H
4-1/4
108
P
24
610
Figure 16.1 See-Through Dimensions
66
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
H
ØK

L
ELECTRICAL
ACCESS
M
TOP VIEW
ØK
C
N
O
D
J
GAS LINE
ACCESS
F
i
E
A
G
H
P
B
FRONT VIEW
LEFT VIEW
Location
Inches
Millimeters
RIGHT VIEW
Location
Inches
Millimeters
A
36
914
I
1-1/2
38
B
40-1/2
1029
J
27
686
C
24-1/2
622
K
8
203
D
33-1/2
851
L
12
305
E
1
25
M
9-1/2
241
F
2-1/8
54
N
38
965
G
4-1/8
105
O
34-5/8
880
H
4-1/4
108
P
24
610
Figure 16.2 Pier Dimensions
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
67
ØK

N
L
ELECTRICAL
ACCESS
M
TOP VIEW
ØK
O
C
P
D
J
GAS LINE
ACCESS
F
i
E
A
G
B
FRONT VIEW
LEFT VIEW
RIGHT VIEW
Location
Inches
Millimeters
Location
Inches
Millimeters
A
36
914
I
1-1/2
38
B
40-1/2
1029
J
27
686
C
24-1/2
622
K
8
203
D
33-1/2
851
L
12
305
E
1
25
M
9-1/2
241
24-1/2
622
F
2-1/8
54
N
G
4-1/8
105
O
38
965
H
4-1/4
108
P
34-5/8
880
Figure 16.3 LCOR, RCOR Dimensions
68
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
H
B. Vent Components Diagrams
Pipe
DVP4
Effective
Height/Length
DVP Pipe (see chart)
Effective Length
Inches
Millimeters
4
102
10-1/2 in.
(267 mm)
45 °
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
10-7/8 in.
(276 mm)
°
DVP45 (45 Elbow)
4-7/8 in.
( 124 mm)
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
7-3/8 in.
(187 mm)
1-1/4 in. (32 mm)
10 in.
(254 mm)
9-1/4 in.
(235 mm)
Assembled
Height: 24 in./610 mm
Diameter: 10 in./254 mm
DVP-AS2
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.4 DVP vent components
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
69
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
12 in.
(305 mm)
DVP-TRAP
Horizontal Termination Cap
Max
Effective
Length
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
Trap1
Trap2
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
DVP-HPC1
DVP-HPC2
Figure 16.5 DVP vent components
70
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
B. Vent Components Diagrams (continued)
31 in.
(787 mm)

13-1/4 in.
(337 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(699 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(337 mm)
RF6M
Roof Flashing Multi-pak

RF12M
Roof Flashing Multi-pak
5 in.
(127 mm)
13-3/4 in.
(349 mm)
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
Flashing
13-7/8 in.
(352 mm)
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
Figure 16.6 DVP vent components

COOL-ADDM
Cap Shield
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
71
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
3-7/8 in.
(98 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
10-1/2 in.
(267 mm)
DVP-TV
VerticalTermination Cap
12 in.
(305 mm)
DVP-TB1
BasementVent Cap
2-3/4 in.
(70 mm)
9 in.
(229 mm)
12 in.
305 mm
12-1/2 in.
(318 mm)
7-1/4 in.
(184 mm)
11-1/2 in.
(292 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
12-1/4 in.
(311 mm)
16 in.
(406 mm)

DVP-TVHW
VerticalTermination Cap (Highwind)
PVK-80
(For use with IPI and DSI appliances only.)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
1 in.
(25 mm)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
12 in.
(305 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
1-5/8 in.
(41 mm)
DVP-HPC
High Performance Cap
3/8 in. (10 mm)
1 in. (25 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
DVP-FBHT
FireBrickTermination Cap
Figure 16.7 DVP vent components
72
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
15 in.
(381 mm)
DVP-HRC-SS
13-5/8 IN.
346 mm
EFFECTIVE LENGTH
32 IN. (813 mm) MIN.
35 IN. (889 mm) MAX.
Optional Wire Harness
DESCRIPTION
12-1/2 IN.
318 mm
PART NUMBER
10 ft. PV Wire Harness
PVI-WH10
20 ft. PV Wire Harness
PVI-WH20
40 ft. PV Wire Harness
PVI-WH40
60 ft. PV Wire Harness
PVI-WH60
80 ft. PV Wire Harness
PVI-WH80
100 ft. PV Wire Harness
PVI-WH100
20-3/4 IN.
527 mm
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately from
PVI-SLP. Contact your dealer to order.
PVI-SLP
Power Vent Inline
16 IN.
406 mm
4-1/2 IN.
114 mm
15 IN.
(381 mm)
9-3/16 IN.
(233 mm)

13-5/8 IN.
(346 mm)
12-1/2 IN.
(318 mm)
16-11/16 IN.
424 mm
16-11/16 IN.
(424 mm)
SLP-LPC
SLP Low Profile Cap
Figure 16.8 Vent Components
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
73
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6 in.
152 mm
9-1/4 in.
235 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP45
45° Elbow
SLP90
90° Elbow
Effective Height/Length
Effective
Height/
Length
SLP-PIPE
SLP-HVS
Horizontal Pipe
Support
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51-152
SLP12A
2 - 12
51-305
SLP-FLEX-2
24
610
SLP-FLEX-3
36
914
SLP-FLEX-5
60
1524
SLP-FLEX-10
120
3048
SLP-FS
Ceiling Firestop
EFFECTIVE HEIGHT/
LENGTH
SLP-FLEX-PIPE
SLP-WS
Wall Shield Firestop
Figure 16.9 SLP Series Vent Components
74
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a
DVP-HSM-B will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Max
Effective
Length
12 in.
(305 mm)
3-1/8 in.
4-3/4 in.
79 mm
121 mm
Trap1
5-1/4 in.
9-1/4 in.
133 mm
235 mm
SLP-TVHW
Vertical
Termination Cap
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLK-SNKD
Snorkel
Termination Cap
Maximum
Effective Length
Trap2
SLP-TRAP
Horizontal Termination Cap

Minimum
Effective Length
DVP-FBHT
Horizontal
Termination Cap
26 in.
660 mm
DVP-2SL
Adapter
SL-2DVP
Adapter
SLP-DCF-BK
Ceiling Firestop
Black
DVP-HSM-B
Extended Heat Shield
SLP-WT-BK
Wall Thimble-Black
Figure 16.10 SLP Series Vent Components
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
75
LCOR-36TRB-IPI
C. Service
Parts
Service
Parts
Beginning Manufacturing Date: Nov 2008
Ending Manufacturing Date: Active
36” Left Corner Gas Fireplace - DV
Log Set Assembly
12
4
1
B
5
3
C
D
A
2
8
7
6
11
10
9
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-2128
A
Log A
SRV2128-701
B
Log B
SRV2128-702
C
Log C
SRV2128-703
D
Log D
SRV2128-706
1
Log 1
SRV2128-704
2
Log 2
SRV2128-705
3
Log 3
SRV2128-707
4
Glass Door Assembly (End)
GLA-2130
Y
5
Burner NG, LP
2128-007
Y
6
Pilot Shield
2128-124
7
Base Pan/Grate Assembly
2128-005
8
Glass Door Assembly (Side)
GLA-750TR
Y
9
Thermostat Wire
2118-170
Y
10
Junction Box
4021-013
Y
11
Junction Box Bracket
2128-128
12
Sheetrock Ledge (Side)
2130-118
Refractory (End)
2129-016
Sheetrock Ledge (End)
2130-126
Surround Overlay (contains overlay for top, bottom and sides)
SRV2132-FACE
Additional service part numbers appear on following page.
76
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Y
3/13
PIER-36TRB-IPI
Service Parts
Beginning Manufacturing Date: Nov 2008
Ending Manufacturing Date: Active
36” Gas Fireplace - DV
Log Set Assembly
14
4
1
B
5
3
D
C
2
A
6
7
9
8
12
11
13
10
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
A
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-2128
Log A
SRV2128-701
B
Log B
SRV2128-702
C
Log C
SRV2128-703
D
Log D
SRV2128-706
1
Log 1
SRV2128-704
2
Log 2
SRV2128-705
3
Log 3
SRV2128-707
4
Sheetrock Ledge (side)
2130-118
5
Refractory Panel
2129-016
6
Burner NG, LP
2128-007
7
Pilot Shield
2128-124
8
Base Pan/Grate Assembly
2128-005
9
Glass Door Assembly (Side)
Qty 2 req
Y
Y
GLA-750TR
Y
10
Thermostat Wire
2118-170
Y
11
Junction Box
4021-013
Y
12
Junction Box bracket
2128-128
13
Glass Door Assembly (End)
GLA-2130
14
Sheetrock Ledge (End)
2130-126
Surround Overlay (contains overlay for top, bottom and sides)
SRV2130-FACE
Additional service part numbers appear on following page.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Y
3/13
77
RCOR-36TRB-IPI
Service Parts
36” Right Corner Gas Fireplace - DV
Beginning Manufacturing Date: Nov 2008
Ending Manufacturing Date: Active
Log Set Assembly
4
14
5
1
B
3
D
C
6
A
2
9
7
8
12
11
10
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-2128
A
Log A
SRV2128-701
B
Log B
SRV2128-702
C
Log C
SRV2128-703
D
Log D
SRV2128-706
1
Log 1
SRV2128-704
2
Log 2
SRV2128-705
3
Log 3
SRV2128-707
4
Sheetrock Ledge (Side)
2130-118
5
Refractory (End)
2129-016
6
Burner NG, LP
2128-007
7
Pilot Shield
2128-124
8
Base Pan/Grate Assembly
2128-005
9
Glass Door Assembly (Side)
GLA-750TR
Y
10
Thermostat Wire
2118-170
Y
11
Junction Box
4021-013
Y
12
Junction Box bracket
2128-128
13
Glass Door Assembly (End)
GLA-2130
14
Sheetrock Ledge (End)
2130-126
Surround Overlay (contains overlay for top, bottom and sides)
SRV2132-FACE
Additional service part numbers appear on following page.
78
13
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Y
Y
Y
3/13
ST-36TRB-IPI
Service Parts
36” See-thru Gas Fireplace - DV
Beginning Manufacturing Date: Nov 2008
Ending Manufacturing Date: Active
Log Set Assembly
4
1
B
5
3
D
C
2
A
6
8
7
10
11
12
9
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-2128
A
Log A
SRV2128-701
B
Log B
SRV2128-702
C
Log C
SRV2128-703
D
Log D
SRV2128-706
1
Log 1
SRV2128-704
2
Log 2
SRV2128-705
3
Log 3
SRV2128-707
4
Sheetrock Ledge
2128-118
Refractory Left
2129-017
Refractory Right
2129-016
5
6
Burner NG, LP
2128-007
7
Base Pan/Grate Assembly
2128-005
8
Glass Door Assembly
9
Qty 2 req
Y
Y
GLA-750TR
Y
Thermostat Wire
2118-170
Y
10
Pilot Shield
2128-124
11
Junction Box
4021-013
12
Junction Box Bracket
2128-128
Surround Overlay (contains overlay for top, bottom and sides)
SRV2128-FACE
Additional service part numbers appear on following page.
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Y
3/13
79
Service Parts
LCOR, PIER, RCOR & ST-36TRB-IPI
Beginning Manufacturing Date: Nov 2008
Ending Manufacturing Date: Active
#15 Valve Assembly
15.1
15.2
15.4
15.3
15.11
15.10
15.9
15.5
15.6
15.7
15.8
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
15.1
15.2
15.3
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Shutter Bracket Assembly
2118-121
Y
Pilot Assembly NG
2090-012
Y
Pilot Assembly LP
2090-013
Y
Flexible Gas Connector
530-302A
Y
Orifice NG (#32C)
582-832
Y
Orifice LP (#50C)
582-850
Y
Valve NG
750-500
Y
Valve LP
750-501
Y
15.6
Battery Pack
593-594A
Y
15.7
Module
593-592
Y
15.8
Flex Ball Valve Assembly
302-320A
Y
15.9
3 Volt Transformer
593-593A
Y
15.10
Module Wire Assembly
593-590A
Y
15.11
Valve Bracket
2118-104
2 in Jumper Wires
2012-206
15.4
15.5
Additional service part numbers appear on following page.
80
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
Y
Service Parts
LCOR, PIER, RCOR & ST-36TRB-IPI
Beginning Manufacturing Date: Nov 2008
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Exhaust Baffle
385-105
Flue Restrictor
385-128
Gasket Assembly
Contains Vent, Seal Cap, Burner Neck, Shutter Bracket and Valve Plate Gaskets
Glass Latch Assembly
Pkg of 2
2128-081
33858/2
Y
Lava Rock
2005-790
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Conversion Kit NG
NGK-MS36
Y
Conversion Kit LP
LPK-MS36
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13
81
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
 This product may be covered by one or more of the following patents: (United States) 5601073, 5613487, 5647340,
5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122,
7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945B
Printed in U.S.A. - Copyright 2013
82
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/13