C-14473 E33GI Owners Manual

N
TIO
RA y
ST nt
GI rra
RE /wa
TY om
AN ro.c
RR nvi
WA e
E33GI
Gas Insert - Glass burner with ipi Valve
OWNER’S MANUAL
WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property damage,
personal injury or loss of life. Installation and service must be
performed by a qualified installer, service agency or the gas
supplier.
Version Française: www.enviro.com/fr.html
50-2578
Safety Precautions
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Leave the building immeadiately.
• Immeadiately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
This appliance may be installed in an after-market permanently located,
manufactured (mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases, unless a certified kit is used.
Massachusetts installations (Warning): This product must be installed by a licensed plumber or
gas fitter when installed within the Commonwealth of Massachusetts. Other Massachusetts code
requirements: Flexible connector must not be longer than 36in., a shut off valve must be installed;
only direct vent sealed combustion products are approved for bedrooms/bathrooms. A carbon
monoxide detector is required in all rooms containing gas fired direct vent appliances. The fireplace
damper must be removed or welded in the open position prior to installation of a fireplace insert.
2
Safety Precautions
FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER,
PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:
• All ENVIRO gas-fired appliances must be installed in
accordance with their instructions. Carefully read all the
instructions in this manual first. Consult the building
authority having jurisdiction to determine the need for a
permit prior to commencing the installation.
• NOTE: Failure to follow these instructions could cause
a malfunction of the fireplace, which could result in death,
serious bodily injury, and/or property damage.
• Failure to follow these instructions may also void your
fire insurance and/or warranty.
GENERAL
• Installation and repair should be done by a qualified
service person. The appliance should be inspected before
the first use and, at least, annually by a qualified service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It
is imperative the control compartments, burners and
circulating air passageways of the appliance be kept
clean.
• A barrier designed to reduce the risk of burns from the
hot veiwing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals. If the barrier becomes damaged, the barrier
shall be replaced with the manufacturer’s barrier for this
appliance
FOR YOUR SAFETY
• Installation and service must be performed by a qualified
installer, service agency or gas supplier.
• This installation must conform to local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54, or the Natural Gas and Propane
Installation Code, CSA B149.1.
• To prevent injury, do not allow anyone who is unfamiliar
with the stove to operate it.
• To prevent injury, if the pilot or pilot and burners
have gone out on their own, open the glass door and
wait 5 minutes to air out before attempting to relight the stove.
• Due to high temperatures, the appliance should be
located out of high traffic areas and away from furniture
and draperies.
• Always keep the area around these appliances clear of
combustible material, gasoline and other flammable liquids
and vapours.
Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burn or clothing ignition.
• These appliances should not be used as a drying rack for
clothing or for hanging Christmas stockings/decorations.
• Young children should be carefully supervised when
in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental
contact burns. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access to a
fireplace or stove install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of
the room and away from hot surfaces. Any safety screen,
guard, or barrier removed for servicing an appliance must
be replaced prior to operating the appliance.
• Clothing or other flammable materials should not be
placed on or near the appliance.

HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED.
• Due to the paint curing on the stove, a faint odor and slight
smoking will likely be noticed when the stove is first used.
Open a window until the smoking stops.
Always connect this gas stove to a vent system and vent to
the outside of the building envelope. Never vent to another
room or inside the building. Make sure the specified vent
pipe is used, properly sized and of adequate height to
provide sufficient draft. Inspect the venting system annually
for blockage and signs of deterioration.
WARNING: Failure to position the parts in accordance
with the diagrams in this booklet, or failure to use only
parts specifically approved with this appliance, may result in
property damage or personal injury.
WARNING: Do not operate with the glass front removed,
cracked or broken. Replacement of the glass should be done
by a licensed or qualified service person.
• Never use solid fuels such as wood, paper, cardboard, coal,
or any flammable liquids, etc., in this appliance.
• Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system or
any gas control which has been under water.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
• Do not abuse the glass by striking it or slamming the door
shut.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
• If the E33GI unit is pulled out of its installation, and the
vent-air intake system is disconnected for any reason,
ensure that the vent-air intake pipes are reconnected and
re-sealed in accordance to the instructions noted in Initial
Installation - Venting Fireplace INserts.
individuals.
3
Table of Contents
Safety Precautions...........................................................................................................2
Table of Contents.............................................................................................................4
Codes And Approvals.......................................................................................................5
Specifications..................................................................................................................6
Rating Label Location...........................................................................................6
Dimensions..........................................................................................................6
Install Depths.......................................................................................................6
E33GI Options Dimensions.....................................................................................7
Operating Instructions.....................................................................................................8
Lighting and Turning Off Instructions.....................................................................8
Venturi Adjustment...............................................................................................9
Normal Sounds During Operation.........................................................................9
Remote Control Operations...................................................................................9
Switching to Continuous Pilot Mode........................................................................10
Wall Mounting the Receiver.................................................................................12
Initializing the System for the First Time..............................................................12
Maintenance And Service................................................................................................15
Cleaning The Glass.............................................................................................15
Cleaning The Firebox..........................................................................................15
Replacing The Glass............................................................................................15
Check Pilot and Burner Flames............................................................................15
Glass Door Removal...........................................................................................16
Cleaning The Painted Surfaces............................................................................16
Removing Valve Cover.........................................................................................17
Fuel Conversion..................................................................................................18
Initial Installation...........................................................................................................20
Clearances to Combustibles.................................................................................20
Minimum Fireplace Size.......................................................................................20
Direct Vent Model...............................................................................................20
Venting Fireplace Inserts.....................................................................................21
Direct Vent Vertical Vent Termination...................................................................23
Installing the Unit...............................................................................................24
Zero Clearance Fireplace Installation...................................................................25
Electrical Requirements.......................................................................................25
Gas Line Connection...........................................................................................27
Adjusting The Pilot Flame....................................................................................28
Secondary Installation....................................................................................................29
Optional Base Shelf & Riser..................................................................................29
Surround Panel Screw Installation.......................................................................30
Optional 3 and 4 sided Trimmable Panels...............................................................31
Surround Panel Installation..................................................................................32
Safety Screen Installation.....................................................................................33
Firebox Liner and Burner Tray Removal / Installation..............................................34
Installing the Glass Burner Media.........................................................................35
Trouble Shooting............................................................................................................37
Parts List.......................................................................................................................40
Parts Diagram - Components..........................................................................................42
Parts Diagram - Options.................................................................................................43
Notes..........................................................................................................................44
Warranty.......................................................................................................................47
Installation Data Sheet...................................................................................................48
4
Codes And Approvals
DIRECT VENT: This type is identified by the suffix DV. This appliance draws all of its air for combustion from
outside the dwelling, through a specially designed vent pipe system.
This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level.
In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas Association
guidelines which state: the sea level rated input of Gas Designed Appliances installed at elevations above 2000
(610 m) feet is to be reduced 4% for each 1000 feet (305 m) above sea level. Refer also to local authorities
or codes which have jurisdiction in your area regarding the de-rate guidelines.
In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certified high altitude
rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).
• This appliance has been tested by OMNI-Test Laboratories and found to comply with the established
VENTED GAS FIREPLACE HEATER standards in CANADA and the USA as follows:
DIRECT VENTED GAS FIREPLACE INSERT HEATER
TESTED AND LISTED TO: ANSI Z21.88-2014/CSA 2.33-2014 VENTED GAS FIREPLACE HEATERS
CAN/CGA 2.17-M91 (R2009) GAS FIRED APPLIANCES FOR HIGH ALTITUDES BY OMNI-TEST LABORATORIES
CSA P.4.1-2009 (R2014) TESTING METHOD FOR MEASURING ANNUAL FIREPLACE EFFICIENCY
This ENVIRO E33GI Fireplace Insert:
• Has been certified for use with either natural or propane gases. (See rating label.)
• Is not for use with solid fuels.
• Is approved for bedroom or bed sitting room. (IN CANADA: must be installed with a permanent wall thermostat
for bedroom installations. Consult the authority having local jurisdiction in your area. IN USA: see current ANSI
Z223.1 for installation instructions.)
• Must be installed in accordance with local codes. If none exist, use current installation code CAN/CGA B149 in
Canada or ANSI Z223.1/NFPA 54 in the USA.
• Must be properly connected to an approved venting system and not connected to a chimney flue serving a
separate solid-fuel burning appliance.
• Is not approved for closet or recessed installations.
IMPORTANT NOTICE (Regarding first fire up): When the unit is turned on for
the first time, it should be turned onto high without the fan on for the first 4
hours. This will cure the paint, logs, gasket material and other products used in
the manufacturing process. It is advisable to open a window or door, as the unit
will start to smoke and can irritate some people. After the unit has gone through
the first burn, turn the unit off, let the unit get cold then remove the glass door
and clean it with a good gas fireplace glass cleaner, available at your local ENVIRO
dealer. See “Door Removal” and “Cleaning The Glass” sections.
COLD CLIMATES:
NOTE: In cold climates, additional insulation may be used on some venting. It is
recommended in cold climates to wrap the exhaust and intake venting for the final
few feet before termination.
5
Specifications
Rating Label Location:
The rating label is located on the left side of the unit, next to the receiver box.
Dimensions:
22.156
18.375
9.095
9.061
*Shown with
Contemporary
surround &
IPI Valve *
11.823
33.000
29.254
27.050
21.520
19.755
16.644
18.030
18.555
19.002
Figure 1: E33GI Exterior Dimensions.
Install Depth:
E33 IPI units have a minimum install depth of 18.375”. The table below shows what depth of
install it will need with each surround panel.
IPI
Surround Panel
Keystone
Contemporary
Extruded
Install Depth
18.375 in
18.375 in
18.375 in
Table 1: Install Depths
6
Nova
Surround Panel
Keystone
Contemporary
Extruded
Install
17.5
17.5
17.5
Specifications
7
43 8 "
1
26 2 "
3
28 4 "
1
45 2 "
Figure 2: E33GI Contemporary Surround with Base Shelf and Riser.
Table 2: E33GI Options Dimensions.
Height
Width
Regular Surround
26.5” (673 mm)
44 1/8” (1121 mm)
Contemporary Surround
26.5” (673 mm)
44 1/8” (1121 mm)
Extruded Surround
26.5” (673 mm)
44 1/8” (1121 mm)
Trimmable
Surround
Height
38” (965mm)
Width
46” (1168mm)
Height
Width
Depth
Base Shelf
1 ⅝” (41 mm)
45 1/2” (1156 mm)
Bottom 4 ⅞” (112 mm); Top 3 13/16” (97 mm)
Base Shelf Riser
2 ⅛” (54 mm)
44” (1118 mm)
3 11/16” (94 mm)
7
Operating Instructions
For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION
MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
Lighting and Turning Off Instructions:
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING:IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
A. This appliance is equipped with an ignition device
C. Use only your hand to push in or
which automatically lights the pilot. Do not try to
turn the gas control knob. Never
light the pilot by hand.
use tools. If the knob will not push
B. BEFORE OPERATING smell all around the
in or turn by hand, don’t try to
appliance area for gas. Be sure to smell next to the
repair it, call a qualified service
floor because some gas is heavier than air and will
technician. Force or attempted
settle on the floor.
repair may result in a fire or
WHAT TO DO IF YOU SMELL GAS:
explosion.
Do not try to light any appliance.
D. Do not use this appliance if any
Do not touch any electrical switch; do not use any
part has been under water.
phone in your building.
Immediately call a qualified service
Immediately call your gas supplier from a
technician to inspect the appliance
neighbor’s phone. Follow the gas supplier’s
and to replace any part of the
instructions.
control system and any gas control
If you cannot reach your gas supplier, call the
which has been under water.
fire department.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Read the owner's manual including the section on
"Remote Control" operation.
3. Set the thermostat to the lowest setting.
4. Turn off all electric power to the appliance.
5. Do not attempt to light the pilot by hand.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above on this label.
If you don't smell gas, go to the next step.
7. Turn on all electric power to the appliance.
8. Using the remote control, set
thermostat to desired setting, or
press the ON/OFF key on the
remote. "ON" will be indicated on the
display of the remote and an audible
"beep" will be heard at the unit to
indicate the command has been
received.
9. This appliance is equipped with a
completely automatic ignition and
lighting control. The control will
attempt to light the pilot several
times if necessary. If it is
unsuccessful, it will discontinue
operations. If the appliance will
not operate, follow the
instructions "To Turn Off Gas To
Appliance" and call your service
technician or gas supplier.
Blue LCD Display
ON/OFF Key
THERMOSTAT Key
UP/DOWN Arrow Key
MODE Key
TO TURN OFF GAS TO APPLIANCE
1. Set thermostat to lowest setting, or press the ON/OFF Key. "OFF" will be indicated on the display
and an audible "Beep" will be heard at the unit to indicate the command has been received.
2. Turn off all electric power to the appliance if service is to be performed.
C-12455
Figure 3: Lighting instruction label.
8
Operating Instructions
Venturi Adjustment:
The venturi adjustment lever is located on the right side of the unit, behind the surround panel (see
Figure 4). To avoid touching hot surfaces under the unit, use the Door Tool to adjust the venturi.
The venturi allows the amount of air coming into the fireplace to be adjusted in order to accommodate
different climates and venting arrangements. Start the pilot and then the burner. Make sure the pilot
flame is burning normally and none of the burner ports are plugged. Let the fireplace burn for roughly
fifteen (15) minutes and then examine the flames. The
ideal flame will be blue at the base and light orange
above. The flames should be of medium height. If the
flames look like this, no venturi adjustment is needed. If
the flames are fairly short and mostly blue, the fireplace
is getting too much air. Therefore, the air shutter should
be closed (push in) slightly until the correct flames are
achieved. Flames that are very orange, with tall dark
stringy tips are not getting enough air. Open (pull out)
the venturi until the flames clean up. If the venturi is
opened, then closed all the way, and the correct flames
Figure 4: Adjusting the venturi air setting.
cannot be attained, turn off the gas and contact the
dealer.
Warning: Incorrect venturi adjustment may lead to improper combustion, which is a safety hazard.
Contact the dealer if there is any concern about the venturi adjustment.
Normal Sounds During Operation:
Component
Sound & Reason
Fire Box
Creaking when heating up or cooling down.
Burner
Light pop or poof when turned off; this is more common with LP units.
Temperature Sensor
Clinking when it senses to turn the blower on or off.
Pilot Flame
Quiet whisper while the pilot flame in on.
Blower / Fan
Air movement that increases and decreases with the speed of the blower.
Gas Control Valve
Dull click when turning on or off, this is the valve opening and closing.
Receiver
Beeps when remote control buttons are pressed.
Table 3: Normal Sound
Remote Control Operations:
The Proflame GTMF is a modular remote control system that directs the functions of the E33GI. The
Proflame GTMF is configured to control the on/off main burner operation, its flame levels and provides on/
off and Smart thermostatic control of the appliance. The system controls a remotely actuated 120V/60Hz
power outlet, fan speed through six (6) levels and has a constantly powered 120V/60Hz power outlet.
9
Operating Instructions
ATTENTION!
- TURN “OFF” THE MAIN GAS SUPPLY OF THE APPLIANCE DURING INSTALLATION OR
MAINTENANCE OF THE RECEIVER.
- PLACE THE RECEIVER’S 3 POSITION SLIDER SWITCH IN THE “OFF” POSITION DURING
INSTALLATION OR MAINTENANCE.
- TURN “OFF” MAIN GAS SUPPLY TO THE APPLIANCE PRIOR TO REMOVING OR REINSERTING
THE BATTERIES IN THE RECEIVER.
- DURING APPLIANCE INSTALLATION/MAINTENANCE OR IN CASE OF REMOTE CONTROL
MALFUNCTION TURN OFF THE FAN CONTROL MODULE USING THE “ON/OFF” MAIN POWER
SWITCH ON THE FRONT PANEL OF THE FCM.
Technical Data
Transmitter (Remote Control):
Supply voltage 4.5 V (three 1.5 V AAA batteries)
Ambient temperature ratings 0 - 50 °C (32 - 122 °F)
Receiver:
Supply voltage 6.0 V (four 1.5 V AA batteries)
Fan Control Module:
Supply voltage/frequency: 120 V / 60 Hz
Aux switched output: 120 V / 60 Hz / 2 A
Fan speed output: 120 V / 60 Hz / 1 Art
System Description:
The Proflame Remote Control System consists of three (3) elements:
1. Proflame Transmitter.
2. Proflame Receiver and a wiring harness to connect the Receiver to the gas valve, stepper motor and
Fan Control Module.
3. Proflame Fan Control Module (FCM)
Switching to Continuous Pilot Mode:
The toggle switch located on the bottom right corner
switches the unit between intermittent and continuous
pilot modes. NOTE: It is recommended to use
the continuous pilot mode during the winter
when the outside temperature is below 50°F
(10°C) to keep the chimney properly heated
for updraft during burner ignition. Continuous
pilot mode also keeps the firebox warm which
eliminates both heat loss to cold air that is trapped
inside the firebox as well as excessive exhaust
vapour condensation on the door glass.
10
Operating Instructions
TRANSMITTER (Remote Control with LCD
Display)
The Proflame Transmitter uses a streamline
design with a simple button layout and
informative LCD display (Figure 5). The
Transmitter is powered by three (3) AAA type
batteries. A Mode Key is provided to Index
between the features and a Thermostat
Key is used to turn on/off or index through
Thermostat functions (Figure 5 & 6).
Figure 5: Proflame Transmitter.
CPI Mode
Figure 6: Proflame Transmitter LCD Screen.
RECEIVER
The Proflame Receiver (Figure 7) connects directly to
the gas valve, stepper motor, DFC, and Fan Control
Module with a wiring harness. The Receiver is
powered by four (4) AA type batteries. The Receiver
accepts commands via radio frequency from the
Transmitter to operate the appliance in accordance
with the particular Proflame system configuration.
The Receiver three (3) position slider switch can be
set to one of three positions: ON (Manual Override),
Remote (Remote control), or Off.
Figure 7: Proflame Receiver.
FAN CONTROL MODULE
Fan Control Module (FCM) offers the added
ability to control the fan speed through six (6)
speeds, a remotely actuated 120V outlet and
a constantly powered 120V outlet. The FCM
provides DC power to the Receiver allowing the
batteries to be used only when line power is
interrupted or lost (see Figure 8).
Figure 8: Proflame Fan Control Module.
11
Operating Instructions
Remote Mounting The Receiver (Optional):
The receiver can be removed from the unit and placed inside a standard Junction type wall box or another
convenient location. This installation can take place up to 6’ft (1.8 m) from the appliance control valve.
1.Connect the wiring harness to the back of the
Receiver.
2.Install the Receiver in the Junction box using the
existing J box screws (Figure 9).
3.Insert the four (4) AA type batteries in the battery
compartment with the correct polarity.
4.Place the slider into the cover plate.
J-Box
Slider
Switch
Receiver
Wall Plate
5.Put the Receiver switch in the “OFF” position.
6.Make sure the Receiver and cover plate words “ON”
and “UP” are on the same side.
7.Align the slider with the switch on the Receiver and
couple the switch into the slider.
8.Align the screw holes.
Figure 9: Wall Mounting the Receiver.
9.Using the two (2) screws provided secure the cover
plate to the Receiver.
Operating Procedure:
Initializing The System For The First Time
Install the four (4) AA batteries into the receiver battery bay. Note the polarity of the battery and insert into
the battery bay as indicated on the Battery cover (+/-). Place the 3-position slider switch in the “Remote”
position (see Figure 7). Using the end of a paper clip, or other similar object, insert the end of the paper clip
into the hole marked “PRG” on the Receiver front cover (see Figure 7).
The Receiver will “beep” three (3) times to indicate that it is ready to synchronize with a Transmitter. Install
the three (3) AAA type batteries in the Transmitter battery bay, located on the base of the Transmitter. With
the batteries already installed in the Transmitter, push the ‘ON’ button. The Receiver will “beep” four (4)
times to indicate the Transmitter’s command is
accepted and sets to the particular code of that
Transmitter. The system is now initialized.
Temperature Indication Display
With the system in the “OFF” position, press the
Thermostat Key and the Mode Key at the same
time. Look at the LCD screen on the transmitter
to verify that a °C or °F is visible to the right of
the Room Temperature display (see Figure 10).
Figure 10: Remote Control Display in Farenheit and Celcius.
Turn on the Appliance
Press the ON/OFF Key on the Transmitter. The Transmitter display will show all active Icons on the screen. A
single “beep” from the Receiver will confirm reception of the command and will commence to first ignite the
pilot light, followed by the main burner. This should take about 10 seconds to complete.
12
Operating Instructions
Turn off the Appliance
Press the ON/OFF Key on the Transmitter. The Transmitter LCD display
will only show the room temperature and Icon (see Figure 11). A single
“beep” from the Receiver confirms reception of the command and both
the pilot light (if the unit is not set to continuous pilot) and main burner
will turn off.
Room Temperature
Thermostat ON
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control the comfort level in a
Set Temperature
room. To activate this function, press the Thermostat Key (see Figure
5). The LCD display on the Transmitter will change to show that the
Figure 11: Remote Control Displays
room thermostat is “ON” and the set temperature is now displayed (see
Set Temperature.
Figure 11). To adjust the set temperature, press the Up or Down Arrow
Keys until the desired set temperature is displayed on the LCD screen of the Transmitter.
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the flame height in accordance to the difference between the set
point temperature and the actual room temperatures. As the room temperature gets closer to the set point
the Smart Function will modulate the flame down. To activate this function, press the Thermostat Key (Figure
6) until the word “SMART” appears to the right of the temperature bulb graphic (Figure 12). To adjust the
set temperature, press the Up or Down Arrow Keys until the desired set temperature is displayed on the LCD
screen of the Transmitter.
Figure 12: Remote Control’s Smart Flame Function.
Remote Flame Control
The Proflame GTMF has six (6) flame levels. With
the system on, and the flame level at the maximum
in the appliance, pressing the Down Arrow Key once
will reduce the flame height by one step until the
flame is turned off. The Up Arrow Key will increase
the flame height each time it is pressed. If the Up
Arrow Key is pressed while the system is on but
the flame is off, the flame will come on in the high
position (refer to Figure 13). A single “beep” will
confirm reception of the command.
Flame Off
Flame Level 5
Flame Level 1
Maximum Flame Level
Figure 13: Remote Control’s Flame Levels.
13
Operating Instructions
Key lock
This function will lock the keys to avoid
unsupervised operation. To activate this function,
press the MODE and UP keys at the same time
and the a lock will appear (see Figure 15). To
de-activate this function, press the MODE and
UP Keys at the same time.
Low Battery Power Detection
Transmitter: The life span of the remote control
Figure 14: Remote Control with Aux for Accent Lights.
batteries depends on various factors: quality
of the batteries used, the number of ignitions
of the appliance, the number of changes to
the room thermostat set point, etc. When
the Transmitter batteries are low, a Battery
Icon will appear on the LCD display of the
Transmitter (see Figure 16) before all battery
power is lost. When the batteries are replaced
this Icon will disappear.
Receiver: The life span of the Receiver batteries
depends on various factors: quality of the
batteries used, the number of ignitions of the
Figure 15: Remote Control
Figure 16: Low Battery
appliance, the number of changes to the room
Locked.
Indicator.
thermostat set point, etc. When the Receiver
batteries are low, No “beep” will be emitted from the Receiver when it receives an On/Off command from
the Transmitter. This is an alert for a low battery condition for the Receiver. When the batteries are replaced
the “beep” will be emitted from the Receiver when the ON/OFF Key is pressed (See Initializing The System
For The First Time).
Manual Bypass Of The Remote System
If the batteries of the Receiver or Transmitter are low or depleted, the appliance can be turned on manually by
sliding the three position slider switch on the Receiver to the ON position. This will bypass the remote control
feature of the system and the appliance main burner will come on.
WARNING: Fire Hazard. Can cause severe injury or death The Receiver causes ignition of the
appliance. The appliance can turn on suddenly. Keep away from the appliance burner when
operating the remote system or activating manual by pass of the remote system.
WARNING: Shock Hazard. Can cause severe injury or death. This device is powered by line
voltage. Do not try to repair this device. In no way is the enclosure to be tampered with or
opened. Disconnect from line voltage before performing any maintenance.
WARNING: Devices rated more than 5A shall not be connected to the OUT receptacle. Devices
rated more than 1A shall not be connected to the FAN receptacle. Devices rated more than 2A
shall not be connected to the AUX receptacle.
CAUTION: Property Damage Hazard. Excessive heat can cause property damage. The appliance
can stay lit for many hours. Turn off the appliance if it is not going to be attended for any length
of time. Always place the Transmitter where children cannot reach it.
14
Maintenance And Service
Warning: Failure to position the parts in accordance with this manual, or failure to use only parts
specifically approved with this appliance, may result in property damage or personal injury.
At least once a year, run through the following procedures to ensure the system is clean and working
properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not
blocked by anything. The pilot flame should be blue with little or no yellow on the tips.
The venting system must be periodically examined; it is recommended the examination is done by a
qualified person.
Cleaning The Glass:
When the fireplace is cool, remove the glass door. See Maintenance and Service - Glass Door Removal.
Check the gasket material on the back of the glass, making sure that it is attached and intact.
During a cold start up, condensation will form on the glass. This is a normal condition with all fireplaces.
However, this condensation can allow dust and lint to cling to the glass surface. Initial paint curing of the
appliance can leave a slight film on the glass. The glass will need cleaning after the fireplace has cooled
off from the first burn and about two weeks after first burn. Use a mild glass cleaner and a soft
cloth. Abrasive cleaners will damage the glass and painted surfaces. Depending on the amount
of use, the glass should require cleaning no more than two or three times a season. Do not clean the
glass when it is hot.
Cleaning The Firebox:
Remove the logs carefully, as they are very fragile. Gently remove all the embers and rock wool and
place on a paper towel. Vacuum the bottom of the firebox thoroughly. Carefully clean any dust off the
logs and remove any lint from the burner and pilot. At this time, inspect the burner tube for cracking or
severe warping. If a problem is suspected, contact the dealer. Check the logs for deterioration or large
amounts of soot; a small amount on the logs is normal. Replace the logs and embers as in the Secondary
Installation - Log Set and Ember Installation section. If new/more embers and rock wool are required,
contact your nearest ENVIRO dealer.
Replacing The Glass:
The glass in the fireplace is a high temperature ceramic. If the glass is damaged in any way, a factory
replacement is required (see Parts List). Wear gloves when handling damaged glass door assembly
to prevent personal injury. Do not operate with the glass front removed, cracked or broken. Removal
and replacement of the glass from the door must be done by a licensed or qualified service person.
The glass must be purchased from an ENVIRO dealer. No substitute materials are allowed.
Remove the door (see page 15). The replacement glass will come with a new gasket installed. Remove
any silicone remnants from the door. Apply high temperature silicone to the two vertical faces of the
door and install the new piece of glass with gasket (be sure to maintain edge clearances). Apply even
pressure to the glass to allow the silicone to adhere to the gasket material.
Check Pilot and Burner Flames:
Periodically do a visual check of the pilot flames. One
flame should encompass the flame sensor and the
other should burn over glass (see Figure 17, pilot shield
partially hidden). Also check that the burner is operating
correctly, refer to Venturi Adjustment section.
Figure 17: Pilot Flame
15
Maintenance And Service
Glass Door Removal:
Figure 18: Door Release.
Figure 19: Door Removal.
Remove the glass door by placing the hooked end of the door release tool in the hole on the
door latch mechanism (see Figure 18) and pulling the latch out then up. When the two (2)
latches have been released, tilt the bottom of the door forward and then lift up to unhook
the top door tabs (see Figure 19).
Re-assemble in the reverse order.
Warning: Do not touch or attempt to remove the glass if the fireplace is not completely cool.
Never operate the fireplace with the glass removed.
CAUTION GLASS MAY SEPARATE FROM DOOR.
Cleaning The Painted Surfaces:
Painted surfaces should be periodically wiped with a damp cloth when the unit is cool.
16
Maintenance And Service
Removing Valve Cover:
The valve cover can be removed to access the gas valve.
1. Use a T-20 screwdriver to remove the eight screws that hold down the valve cover shown in Fig. 20.
VALVE
COVER
Figure 20: Valve Cover.
17
Fuel Conversion
TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY
Please read and understand these instructions before installing.
WARNING: This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturer’s instructions and all applicable codes and requirements of the
authority having jurisdiction. If the information in these instructions is not followed
exactly, a fire, explosion or production of carbon monoxide may result causing property
damage, personal injury or loss of life. The qualified service agency is responsible for
the proper installation of this kit. The installation is not proper or complete until the
operation of the converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
Kit Parts List:
1 - Orifice (NG - #41 DMS or LP #54 DMS)
1 - Conversion label
1 - Servo regulator with diaphragm
1 - Installation instruction sheet
Carefully inspect the orifice supplied with this conversion kit. If it has been damaged or is missing,
contact your dealer, distributor or courier company to have it replaced before starting this installation.
NOTE: The unit is shipped from the factory adjusted for use with NATURAL gas.
1.Ensure all the components of the conversion kit are accounted for.
2.If the unit has already been connected to a gas supply, shut off the gas supply to the unit.
CAUTION: The gas supply must be shut off prior to disconnecting the electrical power and before
proceeding with the conversion.
3.If the unit has been run, shut off and allow cooling to room temperature.
4. Remove the glass as shown in the Maintenance and Service - Glass Door Removal.
5. Carefully remove the log set and ember material if they are installed.
6. Remove the burner as shown in the Maintenance and Service - Burner Removal.
7. Convert the pilot injector:
a)Using a 7/16” wrench, turn the pilot head a ¼ turn counter-clockwise.
b)Push the slider, with your finger or flat head screwdriver.
-Natural gas is marked NAT.
-Propane gas is marked LP with an indicating hole between L and P. It is also marked red.
c) Turn the pilot head a ¼ turn clockwise; back to its original position.
8. Convert the burner orifice(s):
a)Remove the main burner orifice with a 1/2” deep socket.
b)Put a bead of pipe-thread sealant on the orifice threads before installing.
c) Install the new orifice(s) from the kit into the orifice mount. DO NOT OVER-TIGHTEN.
9. Convert the SIT gas valve:
a) Remove Valve Cover.
b) Use a T-20 driver to remove the two screws that hold the servo regulator to the gas valve.
c) Remove the rubber regulator diaphragm that is situated between the servo regulator and the valve body and replace it with the one provided in the kit.
d) Install the LP servo regulator, with the new longer T-20 screws included in the kit.
e) Reinstall the Valve Cover plate.
18
Fuel Conversion
10.Reinstall the burner, porcelain panels, glass tray, glass material, and glass door. Also refer to Secondary
Installation - Firebox Liner & Burner Tray Removal/Installation in your Owner’s Manual. When reinstalling the burner, ensure that the burner to pilot hood relationship is similar to what is shown in
Figure 21.
11.Reconnect the main gas line if it was disconnected and open the shut-off valve at the gas line to the
unit.
12. Use a small brush to apply a warm soapy water solution to all gas connections (use half dish soap
and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by
using an approved pipe thread sealant or approved Teflon tape. NEVER USE AN OPEN FLAME WHEN
TESTING FOR LEAKS.
13.Reconnect the electrical power to the unit.
14. Refer to the Operating Instructions to light the unit and verify proper burner ignition and operation
and proper flame appearance.
15. MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit
has been converted to a different fuel type.
Figure 21. Ignitor assembly beside
the burner ( Shield Hidden).
19
Initial Installation
WARNING: Operation of this heater when not connected to a properly installed and maintained
venting system can result in carbon monoxide (CO) poisoning and possible death.
Clearances to Combustibles:
(FROM UNIT BOT TOM)
Minimum Mantle Clearances
M ANTLE HEIGHT
Maintain sufficient clearances for operation, service and
maintenance.
• A minimum distance of 24” (610 mm) is required
from the centerline of the unit to the sidewalls.
• Minimum clearance for any combustible facing is 30”
(762 mm) from the bottom of the unit.
• A 12” (305 mm) wide mantel can be mounted at a
minimum height of 36” (914 mm) from the bottom of
unit.
• If installed at floor level or up to 4” above floor,
there must be a minimum of 16” (406 mm) of noncombustible material in front of the unit. If the unit
is raised 0-3.9” up, this 16” must be maintained from
the top surface of the combustible material.
• Unit can be installed with combustible material
underneath and in front of unit, as long as it is raised
4” off the floor.
• Minimum ceiling clearance is 60” from bottom of unit.
37”
12” MANTLE
36”
35”
34”
33”
32”
31”
30”
1
2
3
4
5
6
7
8
MANTLE DEPTH
9
10
11
12
Figure 22: Mantle width and height.
Minimum Fireplace Size:
Table 4: Minimum dimensions of fireplace for E33GI to be installed into.
Fireplace Dimensions
Width At Front
32” (813 mm)
Width At Back
20” (508 mm)
Height
20” (508 mm)
Depth
16” (406 mm)
NOTE: Space must be provided for gas line on right side of unit for servicing purposes.
Direct Vent:
WARNING: This appliance has been designed to draw room air for proper heat circulation
from the sides and bottom of the unit, and out the top front. Blocking or modifying these
openings in any way can create hazardous situations.
The vent length for the E33GI must be between 8ft (2.44 m) and 30ft (9.14 m).
This model is vented with a 3” intake and a 3” exhaust aluminum or stainless steel approved flex vent
leading into a vertical termination cap. The flue collars of this model will fit inside of a standard 3” vent
and must be fastened directly to the vent with three screws.. The exhaust vent and air intake are both
located on the top of the unit.
Check periodically that the vents are unrestricted. Also ensure that all direct vent pipes have been
properly sealed and installed after routine inspection or cleaning. The air intake and exhaust pipes must
be installed in the correct locations on the top of the E33GI.
20
Initial Installation
QUALIFIED INSTALLERS ONLY
Venting Fireplace Inserts:
The ENVIRO E33GI may be installed and vented into any solid fuel fireplace that has been installed
in accordance with the National, Provincial/State and local building codes and has been constructed of
non-combustible materials. Before starting, refer to Initial Installation - Preparing Your E33GI For
Installation. Please reference the information in Table 5 and Figures 23, and 25.
An approved chimney liner and rain cap must be used. A throat connector or flashing must be installed to
ensure a tight seal, top performance, safety and efficiency. Carefully follow the manufacturer’s instructions
that accompany the chimney liner kit. Use double walled aluminum flex vent (3” flex conversion piece and
4”x 6 5/8” cap) from any of the following approved products; Simpson Dura-Vent (Direct Vent GS) or (ICC
Excel Direct). If necessary, remove the vent collar plate from the top of the insert and connect it securely
to the liner with sheet metal screws.
Check for any tears in the liner at this point. IMPORTANT: The screws that hold the vent collar plate in its
approved position must be installed.
NOTE: If the E33GI unit is pulled out of its installation, and the vent air intake system is disconnected
for any reason, ensure that the vent-air intake pipes are re-sealed with high-temperature sealant and
reconnected with three (3) sheet metal screws evenly spaced.
Table 5: Vent termination clearances
Minimum Clearance*
Description
3 ft (0.9 m)
Clearance above the highest point where it passes through a roof surface, refer to
Figure 23.
24 in (0.6 m)
Clearance above a roof ridge, any other portion of a building, or any other obstruction within a horizontal distance of 10 feet (3 m), refer to Figure 23.
5 ft (1.5 m)
Clearance for a vent or chimney above either the highest connected appliance
drafthood outlet, or flue collar.
6 ft (1.83 m)
Clearance to mechanical air supply inlet.
3ft (0.9m)
Clearance to each side of center line extended above meter/regulator assembly.
6 ft (1.83 m)
Radial clearance around service regulator vent outlet.
12 in (30 cm)
Clearance above grade, verandah, porch, deck, or balcony.
3 ft (0.9 m)
Clearance to a building opening or combustion air inlet of another appliance, except with the approval of the authority having jurisdiction for the following reduced
clearances.
9 in (0.23 m)
Exception for inputs up to and including 50,000 Btu/h (15kW)
12 in (0.3 m)
Exception for inputs exceeding 50,000 Btu/h (15kW) but not exceeding 100,000
Btu/h (30kW)
*Clearances are in accordance with local installation codes and the requiremenets of the gas supplier
2ft (0.6m)
Minimum
3ft (0.9m)
Minimum
Roof ridge or
any other portion
of a building
Within
10ft (3m)
Figure 23: Roof Clearances.
21
Initial Installation
QUALIFIED INSTALLERS ONLY
3" (76mm) Exhaust
3" (76mm) Intake
Figure 24: Generic Vent Cap Underside.
The height for the vent must be between 8 ft (2.44 m) and 30 ft (9.14 m).
Install a sealed vent cap to prevent leakage of room air up through
chimney.
The intake and the exhaust are 3" (76mm).
Measure the height of the chimney beforehand and purchase the
appropriate venting. Never attempt to over-stretch a flexible liner to
accommodate the height of the chimney. Every joint in the venting must
be secured with three (3) #8 x 3/8” HWH sheet metal screws and an
appropriate sealant (either silicone or stove cement).
The flue damper can be fully blocked open or removed for installation of
the E33GI; the smoke shelves, shields and baffles may be removed if
attached by mechanical fasteners.
The fireplace and fireplace chimney must be clean, in good working order
and constructed of non-combustible materials.
Make sure that all chimney cleanouts are tight fitting and will not permit
air to leak into the chimney.
Refractory, glass doors, screen rails, screen mesh and log grates can be
removed from the fireplace before installing the E33GI.
Figure 25: Installation of E33GI DV .
22
Initial Installation
QUALIFIED INSTALLERS ONLY
Direct Vent Vertical Vent Termination:
INSTALLATION INSTRUCTIONS:
1. Plan your installation and clearances to combustibles. The E33GI may be installed and vented into
any solid fuel fireplace that has been installed in accordance with the National, Provincial/State and
local building codes and has been constructed of non-combustible materials. Also refer to the Initial
Installation - Preparing Your E33GI For Installation and Clearances to Combustibles sections. Refer
to Figure 25 throughout installation.
2. Stretch the Ø3” (76mm) flex vent liners to the length needed to ensure they can be easily connected
to the vent terminals.
3. Install the flex pipe assembly up through the chimney, ensure that the pipe slides through far enough
to connect onto the vent cap.
4. Most vent caps can be installed onto chimneys with flue openings up to 16” (406mm) x 16” (406mm)
and the actual flashing is 18”x18” (refer to Figure 26). If the chimney is smaller the cap should be
trimmed down and folded over.
5. Apply a bead of stove cement sealant to the top section of the Ø3” (76mm) exhaust vent collar plate.
Slide the Ø3” (76mm) flex vent over the flue collar and secure with three (3) sheet metal screws
evenly spaced.
6. Place a bead of high temperature silicone on the intake collar of the fireplace, slide the Ø3” (76mm)
flex intake liner over the collar, secure the flex liner with three (3) sheet metal screws evenly spaced.
7. At the top of the chimney, apply a bead of stove cement sealant to the Ø3” (76mm) pipe of the
exhaust vent terminal (refer to Figure 24). Slide the flex liner onto the vent terminal and secure with
three (3) sheet metal screws evenly spaced.
8. Place a bead of high temperature silicone on the intake collar of the vent terminal (refer to Figure 24).
Slide the Ø3” (76mm) flex intake liner over the collar, secure the flex liner with three (3) sheet metal
screws evenly spaced.
9. Make a tight connection between the gas fireplace insert flue collar and the fireplace chimney at the
top of the chimney. Secure the vent terminal to the chimney using adequate sealant, and according
to local building codes.
APPROVED TERMINATIONS:
-Simpson Dura-Vent
Trim flashing
as required.
46DVA-VCH cap with 46DVA-GK
termination adapter
or
46DVA-CL33 termination kit
-ICC
TM-4SVT cap with TM-CTA
termination adapter
18"
(457mm)
18"
(457mm)
Figure 26: Generic Vent Cap Dimensions.
23
Initial Installation
QUALIFIED INSTALLERS ONLY
Installing the unit:
• Remove the packaging from the appliance and surround panels; check to make sure there is no
damage. Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is
found, please report it to your dealer as soon as possible.
• Carefully clean the fireplace and flue before installing the stove. Failure to do so may result in fumes
or soot being blown into the room and may cause a fire leading to death or serious injury.
1.Remove the unit from the box and remove all packaging material from the appliance.
2.Remove door. See Maintenance and Service - Glass Door Removal.
3.Remove log and ember set and all wrapping material from the stove. Remove wrapping material from
log and embers and check for any damage. If damage is observed, do not use unit and contact your
local dealer.
4. Check that the chimney clean outs fit properly. The flue damper must be fully blocked open or removed
for installation of the E33GI; the smoke shelves, shields and baffles may be removed if attached by
mechanical fasteners.
5.If the fireplace opening is lower than 24” (610 mm), remove the vent collar plate from the top of the
insert by unscrewing the single T-20 Torx screw located on the center top of the stove above the door
opening (see Figure 27). Slide the collar plate backwards. Properly secure the vent collar plate to the
flexible vent pipe liner(s) previously installed in the chimney. Be careful not to over-stretch the liner(s).
6.Place the unit part way into the fireplace. Connect the gas line to the ⅜” NPT pipe nipple at the lower
left rear of the unit using locally approved methods (see Initial Installation - Gas Line Connection).
Place the electric cable so it can be connected to the power supply.
7. As you push the unit into its final position in the fireplace, if the vent collar plate was removed, reinstall
it to the stove by sliding it along the top of the unit and secure with the screw previously removed.
8.Adjust the levelling legs to ensure the unit is level and high enough if a base shelf and/or riser is to be
installed. There are four levelling legs on the bottom of the unit (shown in Figure 28).
Vent Collar Screw
Figure 27: Vent Collar Plate Screw Location.
24
Figure 28: Levelling Legs Position.
Initial Installation
QUALIFIED INSTALLERS ONLY
Zero Clearance (ZC) Fireplace Installation:
The metal floor of the ZC solid fuel firebox can be removed to allow the installation of the insert. THE
CLEARANCE TO COMBUSTIBLE MATERIAL UNDER THE INSERT IS 4” (102 mm). YOU MUST USE THE
LEVELING LEGS TO RAISE THE INSERT A MINIMUM OF 4” (102 mm) IF THE UNIT IS TO BE INSTALLED
ON COMBUSTIBLE MATERIAL. The optional Base Shelf and Riser are recommended to fill the space under
the unit once raised. The sidewalls and top structure of the solid fuel firebox cannot be altered with the
exception of: removal of dampers, removal of smoke shelf or baffle, removal of ember catches, removal
of log grate, removal of viewing screen/curtain, and removal of doors. THE ORIGINAL FIREPLACE MAY
NEVER BE RETURNED TO SOLID FUEL USE IN THIS CONDITION.
IMPORTANT: If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 inch
(37.5 mm) or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship
like manner. This access hole must be plugged with non-combustible insulation after the gas supply line
has been installed. Cutting any sheet-metal parts of the fireplace, in which the gas fireplace insert is to
be installed, except as tested for the floor is prohibited.
The included label plate shown below must be permanently attached inside the cavity of the fireplace
in a visible location.
WARNING: This fireplace has been converted
for the use with a gas fireplace insert only and
cannot be used for burning wood or solid
fuels unless all original parts have been
replaced, and the fireplace re-approved by the
authority having jurisdiction.
C-11168
Figure 29: Fireplace Altered Plate.
Electrical Requirements:
The fireplace must be electrically connected and grounded in accordance with local codes or, in the
absence of local codes, with the current CSA C22.1 Canadian Electrical Code Part 1, Safety Standards For
Electrical Installations, or The National Electrical Code ANSI / NFPA 70 in the US.
WARNING: The electrical grounding instructions must be followed. The fan kit is equipped with a threeprong (grounding) plug for your protection against shock hazard, and should be plugged directly into a
properly grounded three-prong outlet. DO NOT cut or remove the grounding prong from this plug.
CAUTION: When servicing controls, label all wires prior to disconnection. Wiring errors can cause
improper and dangerous operation. Verify proper operation after servicing.
If any of the original wire as supplied with the appliance must be replaced, it must be replaced with 18
AWG wire with a temperature rating of 105°C
25
Initial Installation
5 of 10
QUALIFIED INSTALLERS ONLY
26
Figure 30: Wiring Schematic.
Initial Installation
QUALIFIED INSTALLERS ONLY
Gas Line Connection:
WARNING: Only persons licensed to work with gas piping
may make the necessary gas connections to this
appliance.
Gas Line Connection:
• A ⅜” 45° flared fitting and flex connector are supplied with
the unit (see Figures 31 and 32). Consult the local authorities
for local codes or use the CAN/CGA B149 (1 or 2) installation
code in Canada. In the US, gas installations follow either local
codes or the current edition of the National Fuel Gas Code
ANSI Z223.1.
• If the factory-built fireplace has no gas access hole(s)
provided, an access hole of 1.5 in (37.5mm) or less may be
drilled through the lower sides or bottom of the firebox in a
proper workmanship like manner. This access hole must be
plugged with non-combustible insulation after the gas supply
line has been installed.
Figure 31: Gas Connection Location.
• A shut-off valve is supplied with this unit.
• The appliance and its appliance main gas valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess ½
psi (3.5 kPa). The appliance must be isolated from the gas
supply piping system by closing its equipment shutoff valve
during any pressure testing of the gas supply piping system
at test pressures equal to or less than ½ psi (3.5 kPa).
Figure 32: Gas Valve with Cover
Removed.
Table 6: Orifice and Pressure Information.
E33GI With Log Set & Proflame Valve
Main Burner
Orifice:
Max. Manifold Press:
Min. Manifold Press:
Max. Supply Press:
Min. Supply Press:
Max. Input:
Min. Input:
Natural Gas
Propane Gas
#41 DMS
3.8 W.C. (0.95 KPa)
1.2 W.C. (0.30 KPa)
10.5 W.C. (2.62 KPa)
3.5 W.C. (0.87 KPa)
31,000 BTU/hr (9.09 KW)
17,000 BTU/hr (4.98 KW)
#54 DMS
11.0 W.C. (2.74 KPa)
3.7 W.C. (0.92 KPa)
13.0 W.C. (3.24 KPa)
8.0 W.C. (1.99 KPa)
28,000 BTU/hr (8.21 KW)
16,500 BTU/hr (4.84 KW)
27
Initial Installation
QUALIFIED INSTALLERS ONLY
TO TEST VALVE PRESSURES (INPUT RATES):
The pressure taps are located on the front side of the valve (see Figure 33).
1. Using a long flat bladed screwdriver, turn set screw counter-clockwise to loosen.
2. Place 5/16 in (8 mm) I.D. hose over the pressure taps.
3. Check pressures using a manometer.
4. When finished, remove hose and tighten set screw.
Always check for gas leaks with a soap and water solution after completing the required
pressure test.
NEVER USE AN OPEN FLAME FOR LEAK TESTING.
Item Number
1
2
2
3
3
Description
Pilot Adjustment
Screw
Inlet Pressure Test
Point
Outlet Pressure Test
Point
Table 7: Valve Details.
1
Figure 33: Valve Details.
28
Initial Installation
QUALIFIED INSTALLERS ONLY
Adjusting The Pilot Flame:
The pilot flow adjustment is set to maximum at the factory and should not need to be adjusted. The pilot
flame should envelope ⅜” to ½” (10 to 13mm) of the flame sensor (see Figure 34). However, should the
need arise, follow Steps 1- 2 below.
1. The adjustment screw can be reached through the front of the
unit using a 10 inch long blade head screw driver (see Figure
33 for location on valve).
2. Turn the adjustment screw clockwise to decrease or
counterclockwise to increase pilot flame.
Flame Sensor
.375-.500
(10-13mm)
Figure 34: Proper Pilot Flame.
29
Secondary Installation
Optional Base Shelf & Riser:
The E33GI Base Shelf (1⅝” (41 mm) high) and Base Shelf Riser (2⅛” (54 mm) high) are components
that can be combined to create a riser with an overall height of 23/16” (55 mm). This shelf can be installed
with or without the riser and can be used when the hearth in front of the unit is lower than the fireplace
opening. Additional Base Shelf Risers can be fastened together to increase the height in increments of
2⅛” (54 mm). This Base Shelf may be used in conjunction with the any of the E33GI surround panel
options, and it may also be used with the E33GI Trimmable Surround. The Base Shelf and Riser are sold
separately.
Installation:
1. If unit is running, turn it off and
allow it to cool completely.
2. When using more than one riser
each level must be attached
using nine (9) #8 T-20 screws
provided (see Figure 35).
3. If installing with riser(s) the
Base Shelf is to be fastened
to the riser(s) with one T-20
Figure 36: Installing Base Shelf
screw at each end of the back
onto Riser.
(see Figure 36).
4. The leveling legs on the E33GI may need to be adjusted to match
the height of the riser and shelf.
5. Center the Base Shelf assembly in front of the unit flush with the
bottom of the unit.
6. Install surround if required.
Figure 35: Combining 2 Base Shelf
Riser.
30
Secondary Installation
Optional 3 Trimmable Panels:
Trimmable Panel Install:
The trimmable panel is installed by sliding slots in the panel into screws on the stove. Two screws must
be installed at the bottom of the Side Extensions.
INSTALLATION:
1. Using a T20 screwdriver, screw
one (1) #8-32 x .5” screws
approximately 1/4” into the bottom
of each Side Extension (see Figure
38).
Figure 37: Trimmable Panel Screw
Install.
Figure 38: Trimmable Panel Screw
Install Close-up.
31
Secondary Installation
Optional 3 Trimmable Panels:
Modifying the Surround Panel:
The E33 Trimmable Surround Panels are large rectangular panels that may be cut for use in cases that a nonstandard fireplace opening (e.g. an arched opening) is to be filled. Optionally this surround can be left uncut
and placed in front of the fireplace opening.
1. Measure the fireplace opening and/or make a template of the fireplace opening.
2. Transfer the measurement to the Trimmable Surround.
3. If desired, offset the measurements by approximately 1/8” (3mm) to the inside; this will allow for the panel
to be placed just inside the fireplace opening for a cleaner appearance.
4. Cut along the preferred line (from direct measurements of offset) and remove any sharp edges.
5. The panel can be touched up with a high temperature metallic black paint available from your dealer.
INSTALLATION:
1. Using the supplied hardware install a Trimmable Panel Bracket, on its short leg, onto each side of the stove
using a T-20 Torx screwdriver. See Figure 31 for the screw location and bracket orientation.
2. Install the Trimmable Panel, WITH THE FLANGES FACING OUT, onto the Side Extensions and in front of
the Panel Brackets by hooking the Panel’s top flange onto the alignment pins on top of the Top Extension (See
Figure 39).
3. Using the remaining hardware attach the Trimmable Panel to the Panel Brackets using a T-20 Torx
screwdriver (See Figure 40).
32
Figure 39: Panel Bracket
Installed and Pin Location
Figure 40: Trimmable
Panel Installed
Secondary Installation
Surround Panel Installation:
WARNING: The surround becomes hot when the unit is operating; ensure that the unit is turned off, and that
it has cooled to room temperature before beginning this installation.
3-Sided Surround
26
Height
(673 mm)
1/2”
44
Width
(1121 mm)
1/8”
Table 8: Surround Dimensions.
Please check components supplied with this kit. If components are missing or have been damaged, contact your
dealer, distributor or courier company before starting this installation.
IMPORTANT: The panel must not seal ventilation openings in the fireplace.
INSTALLATION:
If Installing a Contemporary or Extruded surround panel lift the access door up until it locks in place. Lift the
panel upright in front of the fireplace with the top mounting flange pointing towards the fireplace. Slide the panel
over the corresponding screws on top of the Top Extension and at the bottom of the Side Extension on each
side (see Figure 41). Ensure the panel is secure before releasing it. The bottom screws can be tightened on the
Contemporary and Extruded surrounds for a more permanent install.
REMOVAL:
Lift the surround straight up in order to unhook it from the screws. Pull the surround away from the fireplace.
Figure 41: Screw Locations.
BURNER SWITCH WIRING INSTALLATION:
The burner switch supplied with the surround comes pre-installed and wired. The wiring from the burner switch
simply needs to be connected to the wiring on the E33 unit.
The wiring harness for the burner switch has one (1) blue wire, one (1) grey wire and two (2) purple wires.
The blue wire connects to the blue wire on the E33 unit, the grey wire connects to the grey wire on the E33 unit,
and the purple wires are used to connect an optional thermostat.
CLEANING:
Painted surfaces should be periodically wiped with a damp cloth. Never clean the face when it is hot.
33
Secondary Installation
Safety Screen Installation:
Safety Screen Frame
Right Bracket
The safety screen supplied with the unit must be
assembled first before it can be installed. When
installed, the screen should not extrude out any farther
than the surround panel if the cabinet extensions are
still installed.
Safety Screen Assembly
1. Attach the left, right, top/bottom brackets onto
the safety screen using a T20 screwdriver and the
supplied sixteen (16) #8 T20 screws (see Figure
42). Do not over-tighten the screws, doing so
could cause them to strip out of the screen frame.
2. Lift the face upright in front of the fireplace with
the four (4) hooks pointing towards the fireplace.
Slide the hooks into the corresponding brackets
Top/Bottom on each side of the cabinet (see Figure 44).
Bracket
Ensure the hooks are secure before releasing the
safety screen.
Top/Bottom
Bracket
Left Bracket
Figure 42: Installing Safety Screen Mounts.
A
Figure 43: Installing Safety Screen onto
Brackets.
DETAIL A
SCALE 3 : 1
34
Figure 44: Installing Safety Screen onto
Cabinet Bracket (Parts removed for clarity)
Secondary Installation
Firebox Liner and Burner Tray Removal/Installation:
NOTE: The porcelain on the firebox liners can be cracked and chipped easily and should be
handled gently.
WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage, personal injury, or death.
1. Ensure the E33GI is turned off and allow the unit to cool.
2. Remove the glass door as shown in the Maintenance and Service - Glass Door Removal.
WARNING: Do not touch or attempt to remove the door if the fireplace is not completely cool.
Never operate the fireplace with the door removed.
3. Remove the glass material (if installed).
4. Use the following steps to remove the liners and the burner tray.
NOTE: Follow the steps in the reverse order for reassembly.
Figure 45: Remove
the eight T20 screws and
then remove the glass tray panel by lifting up.
Figure 46: Remove
Figure 47: Remove
Figure 48: Remove
the side panel retainer clips
which secure the side.i
the two nuts which hold
down the burner. Gently pull the burner
forward to remove it from the Venturi Box.
back panel.
the side panels then the
35
Secondary Installation
Installing the Glass Burner Media:
Pour the supplied glass media into the tray and evenly distribute over the entire tray area as shown in
Figure 49. There is 3.5lbs of glass included which is just enough for a 0.250” - 0.375” thin layer to cover
the area shown. Ensure that the pilot flame slot remains clear of any glass.
Glass
Figure 49: Glass
tray burner with glass installed.
If the Rock burner option is being installed use the supplied glass media and only fill the burner area as
shown in Figure 50. Fill the burner area until the glass is flush with the bunrner tray, much less glass is
used with this set-up. See instruction sheet with Rocks for further set-up info. ONLY USE SUPPLIED
GLASS MEDIA.
Figure 50: Glass
36
tray burner with glass for Rock Burner.
TroubleShooting
Diagnostic Flash Codes:
1. Fail to ignite: If there is no positive ignition, the board will go into lock out and the LED will blink 3 times
in intervals until the system is reset.
2. Low battery condition (<4V): the LED indicator will blink one (1) time in intervals.
3. Parasitic Pilot Flame: the LED indicator will blink two (2) times in intervals.
4. System Lock out: the LED indicator will blink three (3) times in intervals.
Additional Ignition Information
1. The Proflame DFC Board will try two (2) times for ignition.
2. Each try for ignition will last approximately 60 seconds.
3. The wait time between the two tries is approximately 35 seconds.
Figure 51: Proflame DFC Board with LED Indicator attached.
37
TroubleShooting
Problem
Possible Cause
Thermostat
does not
work
The pilot flame has gone out
The On/Off switch is turn to OFF
The thermostat is set too high
Solution
· Turn it ON
· Set the thermostat to a lower temperature
·  Check pilot assembly wiring
No spark
generation
Spark developes near the pilot
assembly or could occur onboard
·C
heck for broken or poor connection from the sparker to the
electrode
·C
heck for the spark shorting or arcing at other locations
· Check for defective sparker and spark electrode
No pilot
flame ignition
No spark from the igniter
· See “no spark generation”
Air in the gas line
· I t takes a while for all the air to purge out of the pilot before gas
can reach the pilot and ignite
Pilot gas pressure dropout upon
main burner gas valve opening
· Check gas mains supply and pressure
·C
heck gas valve wirings and connections to the board
· Check the pilot burner for obstruction
No gas flow out of the pilot burner
·C
heck the wirings and connections between the pilot assembly and
the board
·C
heck the correct gas type settings on the valve and pilot burner
assembly orifice
·C
heck for proper connection of the Flame Sensor to the DFC board
Problem with Flame Sensor circuit
·C
heck pilot for full flame impingement around Flame Sensor
· I f flame is too small, check gas pressure, adjust pilot rate screw,
check pilot head for damage
Pilot will not
remain lit
· E nsure the ground wire is properly attached to the pilot mounting
bracket and that it is makes a good electrical connection.
Remote
control does
not work
No reaction
to command
38
Restrictor setting
· Use the correct restrictor setting for the venting configuration
The pilot light has gone out
· See “Pilot will not remain lit”
The remote is too far away from
the heater
· Use the remote closer to the heater
The remote control receiver is
turned “OFF”
· Check the remote control instructions
One of the two remote control or
receiver batteries are dead
· Replace the batteries
Receiver or transmitter batteries
are low
· Replace the batteries
A maximum number of failed
ignitions or flame restorations have
been reached.
·R
emove any possible blocking conditions. See “locking conditions”
No communication between the
remote control and the receiver
· Reprogram the transmitter to the receiver.
· See how to reset the board from Lockout
· Follow the initializing system for the first time
TroubleShooting
Problem
Possible Cause
Solution
·T
urn the system off by pressing the ON/OFF button on
the transmitter
·A
fter approximately 2 seconds press the ON/OFF button
on the transmitter again.
Locking
conditions
Reset the Proflame DFC board
· I n the manual flame control mode, use the down arrow
button to reduce the flame to off, indicated by the word
OFF displayed on the transmitter LCD screen.
·W
ait approximately 2 seconds and press the up arrow
button, the ignition sequence will start.
·W
ith the transmitter off, move the slider switch on the
receiver to the OFF position.
· Wait approximately 2 seconds and move the receiver
slider switch to the ON position.
Main burners
will not start
The pilot flame has gone out
· See “Pilot will not remain lit”
The remote control is not working
correctly
· Replace the batteries
The thermostat is disconnected or
set too high
· Set the thermostat to a lower temperature
· Check gas line pressure
Problem with thermopile circuit
· Check wiring to thermostat for breaks
· Check for flame impingement on thermopile
Flame lifting
Leak in vent pipe
· Check for leaks in vent connections
Improper vent configuration
·  Check vent configuration with manual
Terminal may be re-circulating flue
gases
· May need to install high wind termination cap.
· Contact dealer
The heater has just been started
· Normal during start up: flame will yellow as the fireplace
heats up
Improper air shutter adjustment
· Adjust air shutter – contact your dealer
Blue Flames
Normal condition: after the
Glass fogs up appliance warms up the glass will
be clear.
The logs or glasses are placed
incorrectly
Flames are
burning
“dirty” or
sooting
· Check to see if terminal is on correctly
**Due to additives in gas, glass may get hazy during
operation** Clean as needed.
· Check log positioning
· Check level of glasses layout
· I ncrease primary air by opening the air shutter and/or
by opening the vent restrictor
Improper air shutter adjustment
· C
heck for proper venting and blockage of the vent
termination
·  See also “Burners will not remain lit”
Incorrect rating input
·C
heck manifold pressure and clock input rating for overfiring
39
Parts List
Reference
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
-
40
Part Description
Part Number
DV Flue Adaptor Bottom Gasket
Door Release Tool
Door Latch Mechanism (Set of 2)
885 Proflame IPI Valve NG
Burner Control Module
Pilot Shield
PSE IPI Pilot Assembly
E33 Glass Burner Tube Assembly
Fan Only
Fan Control Module
Remote Receiver
120 Ceramic Fan Temp Sensor
Dual Bulb Door Gasket (10ft)
Glass C/W Gasket (21.75” x 13.575”)
Door Complete
Glass Enameled Tray
Pilot Gasket
E33 30 deg. Angled Flue Collar
Porcelain Liner Set
E33GI Owner’s Manual
E33GI Conversion Kit NG to LP
E33GI Conversion Kit LP to NG
Blank Filler Switch
12 oz. Can of Metallic Black Touch Up Paint
Remote Transmitter
Wire Harness - Receiver
50-2516
50-2510
50-2524
50-2682
50-2781
50-2550
50-3026
50-3032
50-2493
50-1572
50-2007
EC-001
50-634
50-2523
50-2522
50-3031
EC-021
50-2630
50-2437
50-2578
50-2489
50-2539
EG30-010
PAINT-12-MB
50-2411
50-2008
Parts List
Reference
Number
25
26
27
28
29
30
31
-
Wire Harness - IPI
50-2009
Option Description
Part Number
Regular Surround Panel
Contemporary Surround Panel
Extruded Surround Panel
Trimmable Surround Panel
Base Shelf
Base Shelf Riser
Safety Screen
E33G/GI Rock Set
50-2428
50-2429
50-2430
50-2432
50-2434
50-2435
50-3073
50-3033
41
Parts Diagram - Components
14
13
11
15
10
12
16
8
17
6
2
7
4
18
1
9
5
3
42
Parts Diagram - Options
25
28
29
26
31
30
27
43
Notes
44
Notes
45
Notes
46
Warranty for Enviro Gas Products
Exclusions
Sherwood Industries Ltd. (“Sherwood”) hereby warrants, subject to the terms and
conditions herein set forth, this product against defects in material and workmanship An expanded list of exclusions is available at www.enviro.com/help/warranty.html
during the specified warranty period starting from the date of original purchase at retail.
In the event of a defect of material or workmanship during the specified warranty period, This warranty does not cover:
 Damage as a result of improper usage or abuse.
Sherwood reserves the right to make repairs or to assess the replacement of a defective
product at Sherwood’s factory. The shipping costs are to be paid by the consumer.
 Damage caused from over-firing due to incorrect setup or tampering.
All warranties by Sherwood are set forth herein and no claim shall be made against
 Damage caused by incorrect installation.
Sherwood on any oral warranty or representation.

Conditions

A completed warranty registration must be submitted to Sherwood within 90 days
of original purchase via the online warranty registration page or via the mail-in
warranty registration card provided. Have the installer fill in the installation data
sheet in the back of the manual for warranty and future reference.

This warranty applies only to the original owner in the original location from date of
install.

The unit must have been properly installed by a qualified technician or installer, and
must meet all local and national building code requirements.

The warranty does not cover removal and re-installation costs.

Sherwood Industries Ltd. reserves the right to make changes without notice.

Sherwood Industries Ltd. and its employees or representatives will not assume
any damages, either directly or indirectly caused by improper usage, operation,
installation, servicing or maintenance of this appliance.

A proof of original purchase must be provided by you or the dealer including serial
number.
Category
Parts
1
One Year
Any discolouration of the safety screen.
To the Dealer

Provide name, address and telephone number of purchaser and date of purchase.

Provide date of purchase. Name of installer and dealer. Serial number of the
appliance. Nature of complaint, defects or malfunction, description and part #
of any parts replaced.

Pictures or return of damaged or defective product may be required.
To the Distributor

Sign and verify that work and information are correct.
Sherwood Industries Ltd.
6782 Oldfield Road, Victoria, BC . Canada V8M 2A3
Online warranty registration: www.enviro.com/warranty/
Two Year

(unit serial number required)
Firebox Liner Panels
Limited Lifetime (7yr)
Ceramic
(excluding porcelain)
Heat Exchanger
Burner
Ceramic Logs
2
Ceramic Glass

3
Pedestal / Legs



(excluding finish)
Door Assembly
Surround Panels
Exterior Panels
(excluding finish)
Up to 5 years
(excluding finish)
Electrical Components
Exterior Surface Finishing
4
Labour
1
Steel




Firebox



Whereas warranty has expired, replacement parts will be warrantied for 90 days from part purchase date. Labour not included.
Unit serial number required.
2
Log set and panels excludes wear and tear or breakage caused by cleaning or service.
3
Glass is covered for thermal breakage. Photos of box, inside of door, and unit serial # must be supplied for breakage due to shipping.
Exterior Surface finishing covers plating, enamel or paint and excludes colour changes, chipping, and fingerprints.
Travel costs not included.
4
Jan 2013
47
Installation Data Sheet
The following information must be recorded by the installer for warranty purposes and future reference.
NAME OF OWNER:
NAME OF DEALER:
_________________________________________
_________________________________________
ADDRESS:
ADDRESS:
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
PHONE:___________________________________
PHONE:___________________________________
MODEL:___________________________________
NAME OF INSTALLER:
SERIAL NUMBER:___________________________
DATE OF PURCHASE: _____________
_________________________________________
(dd/mm/yyyy)
DATE OF INSTALLATION:___________(dd/mm/yyyy)
� DIRECT VENT
� B-VENT
� NATURAL GAS (NAT)
� PROPANE(LPG)
ADDRESS:
_________________________________________
_________________________________________
INLET GAS PRESSURE:_________in WC
_________________________________________
PHONE:___________________________________
MAIN BURNER ORIFICE:__________# DMS
PILOT ORIFICE #_________OR________in diam.
INSTALLER’S SIGNATURE:
_________________________________________
MANUFACTURED BY:
SHERWOOD INDUSTRIES LTD.
6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3
www.enviro.com
September 17, 2015
C-14473
48