pfdata

PEM® CAPTIVE PANEL SCREWS
BULLETIN
PF
415
Rev 416
PEM® CAPTIVE PANEL SCREWS
PEM brand captive panel screws are designed to help keep parts to a minimum and eliminate risks associated with
loose hardware that could fall out and damage internal components. These panel fastener assemblies are ideal to
attach metal panels or other thin material components in applications where subsequent access will be necessary.
Types PF11/PF12/PF11M/PF12M large
knob, spring-loaded self-clinching panel
screws - PAGE 5
Types PFC2/PFS2 screw head, spring-loaded
captive panel screws - PAGE 16
Type PF11MF large knob, spring-loaded
flare-mounted captive panel screws PAGE 6
Types PTL2/PSL2 locating pin, springloaded plunger assemblies - PAGE 17
Type PF11MW large knob, spring-loaded
flare-mounted, floating captive panel screws
- PAGE 7
Type SCBR tool only, spinning clinch bolt
with spring - PAGE 18
Type PF11PM large knob, spring-loaded
plastic PEM® C.A.P.S.™ captive panel
screws - PAGE 8
Types SCB/SCBJ tool only, spinning clinch
bolts, no spring - PAGE 19
Type PFHV screw head, no spring captive
panel screws - PAGE 9
Types HSCB, HSR, and HSL heat sink
mounting fastener system - PAGES 20 - 21
Type PF7M screw head, spring-loaded selfclinching captive panel screws - PAGE 10
Type PF10 tool only, flush-mounted captive
panel screws, no spring - PAGES 22 - 23
Type PF7MF flare-mounted captive panel
screws for installing into stainless steel PAGE 11
REELFAST® Type SMTPFLSM surface
mount spring-loaded captive panel screws PAGE 24
Type PF30 low-profile knob, spring-loaded
captive panel screws - PAGE 12
REELFAST® SMTPF surface mount, panel
screw components and assembly data PAGE 25
Types PF50 and PF60 low-profile knob,
spring-loaded captive panel screws PAGE 13
Type PFK screw head, spring-loaded
broaching captive panel screws - PAGE 26
Type PFC4 recessed-head captive panel
screws for installing into stainless steel PAGE 14
Value-added capabilities - PAGE 27
!
NEW
Captive panel screw installation - PAGES 28 - 36
Captive panel screw performance data - PAGES 37 - 41
Type PFC2P tool only, non flush, springloaded captive panel screws - PAGE 15
Captive panel screw capabilities - PAGE 42
HEIGHT COMPARISON GUIDE AND STANDARD DRIVER RECESS
PF11/PF12
PF11M/PF12M
PF11MF
PF11MW
PEM C.A.P.S.®
PF7M/PF7MF
PFC2P
PFC4
PAGE 5
PAGE 6
PAGE 7
PAGE 8
PAGES 10 & 11
PAGE 15
PAGE 14
Installed
and
fastened
height
above
sheet.
PF-2 PennEngineering • www.pemnet.com
CAPTIVE PANEL SCREW SELECTOR GUIDE
Application Requires:
ctuation
A
Installs into
Includes
PEM
Min.
Available
anti
Mating
Panel
High
sheet PrintedStainless
Multiple Flush Available in
cross- hole
Fastener Page corrosion Spring ToolHand aluminum circuit
steel Painted screw mounted
in
custom threading misaType No. UL
Approved resistance loaded
or steel boards
sheet
panels lengths top side black
colors feature lignment
®
PF11
5•
•
•••
PF11M
5•
•
••••
PF12
5•
•••
PF12M
5•
••••
PF11MF
6•
•
•
••••••
PF12MF
6•
•••••••
PF11MW
7•
•
•
•••••••
PF12MW
7•
••••••••
PEM C.A.P.S.
8•
•
••
•(1)• •
PFHV
9
•••
PF7M
10•
•
•••
PF7MF
11•
•
•••••• •
PF30
PF31
12•
•
••
PF32
PF50
PF51
13•
•
•••
PF52
PF60
PF61
13•
•••
PF62
PFC4
14••
•••
PFC2P
15
••
•••
PFC2
16 •
•
•
•••
PFS2
16•
•
•••
SCBR 18
• •
SCB/SCBJ
19
••
HSCB 20-21 •
PF10
22-23
••
•••
SMTPFLSM
24•
•
••••
SMTPF
25
•
••••(1)•
PFK26 ••
•
••••
(1) Standard color is black.
PFC2/PFS2
PFK
PF50/PF51/PF52
PF60/PF61/PF62
PF30/31/32
HSCB
PFHV
SCBR
SCB/SCBJ
PAGE 18
PAGE 16
PAGE 13
PAGE 12
PAGES 20 & 21
PAGE 19
PF10
PAGES 22 & 23
PAGE 9
PennEngineering • www.pemnet.com
PF-3
PEM® TYPE PF11™/PF12™ CAPTIVE PANEL SCREWS
The PEM® Type PF11/PF12 family of panel fasteners provide design flexibility by offering three styles of installation types,
each having the same profile or look above the sheet or panel into which it is installed. The various mounting types include
self-clinching, flare-mounted, and floating styles. Each offers a distinct advantage depending on your application. The
standard selection of knobs include knurled or smooth metal caps and plastic PEM C.A.P.S.® (colored access panel screws).
Key features include:
Self-clinching
1
2
Flare-mounted
Universal
Phillips/
slot
drive*
3
1)Universal Phillips/slot drive (except for plastic cap).
2)Shoulder on retainer to provide positive stop during
installation.
3)Anti cross-threading feature. Eases assembly, aligns
components, improves assembly line productivity, prevents
jamming, and slides through clogged internal threads.
Floating
ANTI CROSS-THREAD TECHNOLOGY - HOW IT WORKS
PennEngineering is a licensee for MAThread® technology, a registered trademark of MAThread Inc.
Shoulder
on
retainer
-1-
-2-
MISALIGNED AXIS
THREADS CAM
-3-
THREADS DRIVE NORMALLY
* Plastic cap version has Phillips drive only.
Standard Mounting Styles:
Self-clinching
• Installs flush on back side of panel.
• Available in three screw
lengths.
Flare-mounted
• Appropriate for close centerline-to-edge
applications.
• Doesn’t require high installation
force.
• Installs into any panel hardness.
• Installs flush on back side of panel.
• Can be installed into most any thin
material.
• Appropriate for painted panels.
Flare-mounted, Floating
• Compensates for mating hole misalignment.
• Installs into any panel hardness.
Standard Cap Selection:
Metal Cap knurled
All metal cap available
with knurls.
Metal Cap Un-knurled
All metal cap available
without knurls.
Black Metal Cap
DuraBlack™ finish is scratch resistant.
Finish is on both metal cap and screw.
(finish code “BL”)
Plastic Cap
Available with custom
color plastic cap.
(See page 8 for colors)
Available Drive Configurations:
PF11
Phillips/slot
(Standard except for plastic cap)
PF-4 PennEngineering • www.pemnet.com
PF11P
PF11LS
PF11S
PF11L
Phillips
Torx®/Slot
Combination
(Optional)
Slotted
Torx®/Torx Plus®
(Optional)
(Optional)
(Optional)
PennEngineering is a licensee for Acument Global Technologies (Torx®, Torx Plus®)
PEM® TYPES PF11™/PF12™/PF11M/PF12M CAPTIVE PANEL SCREWS
Dimples on head
designate metric thread.
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g
Phillips
driver size.
Type PF11
(See chart)
Knurled Cap
Type PF12
Finish:
Optional Finish (BL):
Knob: Natural Finish
Knob: Black anodize (2)
Retainer: Bright nickel over copper flash
Screw: Black nitride,
per ASTM B689
AMS2753, Section 3 (2)
Screw (Type PF11/PF12): Passivated and/or tested per ASTM A380
Screw: (Type PF11M/PF12M): Zinc plated, 5µm, colorless (3)
Spring: Natural Finish
Smooth Cap
E
Shoulder
provides
positive
stop during
installation.
Material:
Knob: Aluminum
Retainer: Hardened Carbon Steel
Screw (Type PF11/PF12): 400 Series Stainless Steel
Screw (Type PF11M/PF12M): Hardened Carbon Steel (1)
Spring: 300 Series Stainless Steel
T2
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale) / HB 150 or less (Hardness Brinell)
T1
PART NUMBER DESIGNATION
P
C
PF11
G
A
M–
632– 1
BL
Clinching profile may vary.
Float .010”/0.25mm minimum, in all directions from center, .020”/0.5mm total.
Type Optional
Thread
Anti-cross
Code
thread feature
Installation Data page 28. Performance Data page 36.
Screw Optional
Length DuraBlack
Code
finish
All dimensions are in inches.
UNIFIED
Thread
Size
Type
Knurled
Cap
Smooth
Cap
Thread
Code
.112-40
(#4-40)
PF11
PF12
PF11M PF12M
440
.138-32
(#6-32)
PF11
PF12
PF11M PF12M
632
.164-32
(#8-32)
PF11
PF12
PF11M PF12M
832
.190-32
(#10-32)
PF11
PF12
PF11M PF12M
032
.250-20
(1/4-20)
PF11
PF12
PF11M PF12M
0420
Screw
Length
Code
0
1
2
0
1
2
0
1
2
0
1
2
0
1
2
A
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ .003
- .000
C
Max.
E
± .010
.036
.036
.219
.218
.417
.036
.036
.250
.249
.450
.036
.036
.312
.311
.514
.036
.036
.312
.311
.514
.036
.036
.375
.374
.575
A
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ 0.08
C
Max.
E
± 0.25
0.92
0.92
5.56
5.54
10.59
0.92
0.92
6.35
6.33
11.43
0.92
0.92
7.92
7.9
13.06
0.92
0.92
7.92
7.9
13.06
0.92
0.92
9.53
9.5
14.61
G
± .025
P
± .025
.170
.230
.290
.230
.290
.350
.230
.290
.350
.230
.290
.350
.290
.350
.410
.000
.060
.120
.000
.060
.120
.000
.060
.120
.000
.060
.120
.000
.060
.120
G
± 0.64
P
± 0.64
4.32
5.84
7.37
5.84
7.37
8.89
5.84
7.37
8.89
5.84
7.37
8.89
7.37
8.89
10.41
0
1.52
3.05
0
1.52
3.05
0
1.52
3.05
0
1.52
3.05
0
1.52
3.05
T1
Nom.
T2
Nom.
Driver
Size
Min. Dist.
Hole
C/LTo
Edge
.310
.450
#1
.28
.450
.640
#2
.29
.450
.640
#2
.33
.450
.640
#2
.33
.530
.790
#3
.46
T1
Nom.
T2
Nom.
Driver
Size
Min. Dist.
Hole
C/LTo
Edge
7.87
11.43
#1
7.11
11.43
16.26
#2
7.37
11.43
16.26
#2
8.38
11.43
16.26
#2
8.38
13.46
20.07
#3
11.68
All dimensions are in millimeters.
METRIC
Thread
Size x
Pitch
Type
Knurled
Cap
Smooth
Cap
Thread
Code
M3 x 0.5
PF11
PF12
PF11M PF12M
M3
M3.5 x 0.6
PF11
PF12
PF11M PF12M
M3.5
M4 x 0.7
PF11
PF12
PF11M PF12M
M4
M5 x 0.8
PF11
PF12
PF11M PF12M
M5
M6 x 1
PF11
PF12
PF11M PF12M
M6
Screw
Length
Code
0
1
2
0
1
2
0
1
2
0
1
2
0
1
2
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) “BL” suffix will be added to part number to designate DuraBlack™ finish.
(3) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
PennEngineering • www.pemnet.com
PF-5
PEM® TYPE PF11MF™ FLARE-MOUNTED CAPTIVE PANEL SCREWS
Dimples on head
designate metric thread.
Type PF11MF
Phillips
driver size.
Knurled Cap
Type PF12MF
(See chart)
Smooth Cap
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Knob: Aluminum
Retainer: Aluminum
Screw: Hardened Carbon Steel
Spring: 300 Series Stainless Steel
Finish:
Knob: Natural Finish
Retainer: Natural Finish
Screw: Zinc plated, 5µm, colorless (3)
Spring: Natural Finish
Optional Finish (BL):
Knob: Black anodize (2)
Screw: Black nitride
AMS2753,
Section 3 (2)
E
Shoulder
provides
positive
stop during
installation.
PART NUMBER DESIGNATION
T2
C
T1
PF11
PF12
G
Type
A
P
M
M
F–632–1
F–632–1
Anti-cross FlareThread mounted
Style
Feature
BL
Thread Screw Optional
Code Length DuraBlack
finish
Code
Float .010”/0.25mm minimum, in all directions from center, .020”/0.5mm total.
Installation Data page 28. Performance Data page 36.
All dimensions are in inches.
Type
Hole Size
Screw
Min.
Thread
Thread
A
In Sheet
C
E
G
P
T1T2
Driver
Length
Sheet
Size KnurledSmoothCode
Max.
+ .005
Max.
± .010
± .025
± .025
Nom.
Nom.
Size
Code
Thickness
Cap Cap
- .000
.112-40 0 .170.000
PF11MFPF12MF
4401 .041 .031 .187 .186.417.230.055 .310.450 #1
(#4-40)
2.290
.115
0 .230.000
.138-32
PF11MFPF12MF
6321 .072 .060 .213 .212.450.290.024 .450.640 #2
(#6-32)
2.350
.084
0.230
.000
.164-32
PF11MFPF12MF
8321 .072 .060 .266 .265.514.290.024 .450.640 #2
(#8-32)
2.350
.084
0.230
.000
.190-32
PF11MFPF12MF
0321 .072 .060 .266 .265.514.290.024 .450.640 #2
(#10-32)
2.350
.084
0 .290.000
.250-20
PF11MFPF12MF
04201 .072 .060 .323 .322.575.350.024 .530.790 #3
(1/4-20)
2.410
.084
UNIFIED
All dimensions are in millimeters.
Type
Screw
Min.
Hole Size
Driver
Thread
Thread
A
C E G P T1T2
Length
Sheet
In Sheet
Size x
KnurledSmooth Code
Max.
Max.
± 0.25
± 0.64
± 0.64
Nom.
Nom.
Size
Code
Thickness
+ 0.1
Pitch
Cap
Cap
0
4.32
0
M3 x 0.5 PF11MFPF12MFM3 1
1.05 0.79 4.75 4.73 10.59 5.84 1.4 7.87 11.43 #1
2
7.37
2.92
0
5.84
0
M4 x 0.7 PF11MFPF12MF
M4 1 1.83 1.52 6.76 6.7413.067.37 0.6111.43
16.26 #2
2
8.89
2.13
0
5.84
0
M5 x 0.8 PF11MFPF12MF
M5 1 1.83 1.52 6.76 6.7413.067.37 0.6111.43
16.26 #2
2
8.89
2.13
0
7.37
0
M6 x 1 PF11MFPF12MF
M6 1 1.83 1.52 8.2 8.1814.618.89 0.6113.46
20.07 #3
2
10.41
2.13
METRIC
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) “BL” suffix will be added to part number to designate DuraBlack™ finish.
(3) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
PF-6 PennEngineering • www.pemnet.com
PEM® TYPE PF11MW™ FLARE-MOUNTED, FLOATING CAPTIVE PANEL SCREW
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Knob: Aluminum
Retainer: Aluminum
Screw: Hardened Carbon Steel
Spring: 300 Series Stainless Steel
Washer: 300 Series Stainless Steel
Dimples on head
designate metric thread.
Finish:
Knob: Natural Finish
Retainer: Natural Finish
Screw: Zinc plated, 5µm,
colorless (3)
Spring: Natual Finish
Phillips
driver size.
Type PF11MW
Knurled Cap
(See chart)
Type PF12MW
Smooth Cap
Optional Finish (BL):
Knob: Black anodize (2)
Screw: Black nitride,
AMS2753,
Section 3 (2)
E
Shoulder
provides
positive
stop during
installation.
PANEL CONFIGURATION 1
For applications where a space
between mating panels is acceptable.
T2
T1
PANEL CONFIGURATION 2
For applications where a space between
mating panels is not acceptable.
D
A
D
B
L
W
.025” / 0.64mm Nom.
G
A
H
PART NUMBER DESIGNATION
PF11
PF12
M
M
W–632–1
W–632–1
1
1
BL
Installation Data page 29. Performance Data page 36.
Type
Anti- Floating Thread Shank Screw Optional
style Code Code (4) Length DuraBlack
cross
finish
Code (4)
Thread Feature
Type PF11MW panel fasteners are shipped with mating washers.
All dimensions are in inches.
UNIFIED
Type
Screw
A
D Hole Size
Thread
Thread Shank Length Max.
B
In Sheet
E
G
H
L
T1T2 DriverMin. W
Size KnurledSmooth CodeCodeCode Sheet Min. +.003 ±.010Nom. Min. Nom.Nom.Nom. Size Total Nom.
Cap
Cap
(4)
(4)
Thickness–.001
Float
.112-40
1
.230
1
.063.111.250.417 .375 .137.310.450 #1 .073.312
(#4-40) PF11MWPF12MW 440
2
.290
.138-32
1
.290
1
.063.115.283.450 .413 .149.450.640 #2 .076.344
(#6-32) PF11MWPF12MW 632
2
.350
.164-32
1
.290
1
.063.121.346.514 .469 .157.450.640 #2 .076.407
(#8-32) PF11MWPF12MW 832
2
.350
.190-32
1
.290
1
.063.121.346.514 .469 .157.450.640 #2 .076.407
(#10-32) PF11MWPF12MW 032
2
.350
.250-20
1
.350
.063.128.413.575 .531 .157.530.790 #3 .081.468
(1/4-20) PF11MWPF12MW 0420 1
2
.410
METRIC
All dimensions are in millimeters.
Type
Screw
A
D Hole Size
ThreadThread
Shank
Length
Max.B
In Sheet
EGHLT1T2 DriverMin. W
Size x
KnurledSmooth CodeCodeCode Sheet Min. +0.08 ±0.25Nom. Min. Nom. Nom. Nom. Size Total Nom.
PitchCapCap
(4)
(4)
Thickness–0.03
Float
1
5.84
M3 x 0.5 PF11MW PF12MW M3
1
1.62.82 6.3510.59 9.523.487.8711.43 #1 1.857.92
2
7.37
7.37 10.493.7811.4316.26 #2 1.93 8.74
1 1.62.92 7.1911.43
M3.5 x 0.6 PF11MW PF12MW M3.5
1
2
8.89
7.37 11.913.9911.4316.26 #2 1.9310.34
1 1.63.07 8.7913.06
M4 x 0.7 PF11MW PF12MW M4
1
8.89
2
7.37
1
M5 x 0.8 PF11MW PF12MW M5
1
1.63.07 8.7913.06 11.913.9911.4316.26 #2 1.9310.34
8.89
2
1
8.89
M6 x 1 PF11MW PF12MW M6
1
1.6 3.25 10.4914.61 13.483.9913.4620.07 #3 2.0611.89
10.41
2
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) “BL” suffix will be added to part number to designate DuraBlack™ finish.
(3) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
(4) Other shank and screw lengths available.
PennEngineering • www.pemnet.com PF-7
PEM® C.A.P.S.® CAPTIVE PANEL SCREWS
Color Capabilities
(1)
Choose a knob color code and add it to the end of the base part number.
Dimples on head
designate metric thread.
Patented.
Red = R
Phillips
driver size.
Shoulder
provides
positive
stop during
installation.
T1
C
A
G
Clinching profile may vary.
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale)
HB 150 or less (Hardness Brinell)
PART NUMBER DESIGNATION
PF11
P
Type
Phillips
Drive
M–632–0
B
Also available
with flare-mounted
retainer as Type
PF11PMF or with
floating style
retainer as Type
PF11PMW.
Float .010”/0.25mm minimum, in all directions from center, .020”/0.5mm total.
Installation Data page 28. Performance Data page 37.
All dimensions are in inches.
Violet = V Metallic = M
Finish:
Retainer:CN - Bright nickel over
copper flash per ASTM B689
Screw: Zinc plated, 5µm, colorless (4)
Spring: Natural Finish
T2
P
Blue = U
Material:
Knob: PC/ABS (UL 94V-0, halogen-free) (3)
Retainer: Hardened Carbon Steel
Screw: Hardened Carbon Steel
Spring: 300 Series Stainless Steel
Black = B
(Standard)
E
Green = G
Threads:
External, ASME B1.1, 2A /
ASME B1.13M, 6g (2)
PEM® C.A.P.S.® dot
pattern identifier
(patented)
(See chart)
Orange = N Yellow = Y
Anti- Thread Screw Color
cross Code Length Code
Thread
Code (Standard
Feature
Black)
Type
Hole Size
Min. Dist.
ScrewA
Min.
Thread
Thread
In Sheet
C
E
G
P
T1T2
DriverHole
Length(Shank)
Sheet
Size
Knurled
Code
+ .003
Max.
± .010
± .025
± .025
Nom.
Nom.
Size
C/LTo
CodeMax.
Thickness
Cap
- .000
Edge
0
.170
.000
.112-40
PF11PM440 1 .036.036 .219 .218.417.230 .060.310.450 #2 .28
(#4-40)
2
.290
.120
0
.230
.000
.138-32
PF11PM632 1 .036.036 .250 .249.450.290 .060.450.640 #2 .29
(#6-32)
2
.350
.120
0
.230
.000
.164-32
PF11PM832 1 .036.036 .312 .311.514.290 .060.450.640 #2 .33
(#8-32)
2
.350
.120
0
.230
.000
.190-32
PF11PM032 1 .036.036 .312 .311.514.290 .060.450.640 #2 .33
(#10-32)
2
.350
.120
UNIFIED
All dimensions are in millimeters.
Type
Min. Dist.
Thread
ScrewA
Min.
Hole Size
Thread
C E G P T1T2
DriverHole
Size x
Length(Shank)
Sheet
In Sheet
Knurled
Code
Max.
± 0.25
± 0.64
± 0.64
Nom.
Nom.
Size
C/LTo
Pitch
CodeMax.
Thickness
+ 0.08
Cap
Edge
0
4.32
0
M3 x 0.5
PF11PM
M3
1
0.92
0.92
5.56
5.54
10.59
5.84
1.52
7.87
11.43
#2
7.11
2
7.37
3.05
0
5.84
0
M4 x 0.7
PF11PM
M4
1
0.92
0.92
7.92
7.9
13.06
7.37
1.52
11.43
16.26
#2
8.38
2
8.89
3.05
0
5.84
0
M5 x 0.8
PF11PM
M5
1
0.92
0.92
7.92
7.9
13.06
7.37
1.52
11.43
16.26
#2
8.38
2
8.89
3.05
METRIC
(1) The colors shown (except for black) are non-stocked standards and available on special order. Since actual color knob may vary slightly
from those represented, we recommend that you request samples for color verification. If you require a custom color or you need a “color
matched” knob, please contact us.
(2) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(3) Temperature limit is 210˚ F / 99˚ C.
(4) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
PF-8 PennEngineering • www.pemnet.com
PEM® TYPE PFHV™ CAPTIVE PANEL SCREWS
• Low cost captive screw design to replace loose hardware.
• Small, compact and low profile design for limited access areas.
• Two screw lengths.
• Universal slot/Phillips recess standard.
• Available with MAThread® anti cross-thread technology. (See page 4 for more information).
• Available with Torx® recess.
Phillips
driver size.
(See chart)
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Dimples on
head designate
metric thread.
Material:
Retainer: Carbon Steel
Screw: Hardened Carbon Steel
For available drive
configurations, see page 4.
Finish:
Retainer:CN - Bright nickel over copper flash per ASTM B689
Screw:CN - Bright nickel over copper flash per ASTM B689 (1)
For use in sheet hardness:
HRB 60 or less (Hardness Rockwell “B” Scale)
HB 107 or less (Hardness Brinell)
E
T2
H
T1
P
A
C
Shoulder
provides
positive
stop during
installation.
PART NUMBER DESIGNATION
PFHV–632– 0
G
Clinching profile may vary.
Type
Thread Size
Code
CN
Screw Finish
Length Code
Code
Installation Data page 29. Performance Data page 37.
UNIFIED
All dimensions are in inches.
ScrewA
Hole Size
Min.
Min. Dist.
T2
Driver
Thread TypeThread
C
E
G
H
P
T1
HoleC/L
Length(Shank) Sheet In Sheet
Size Code CodeMax. Thickness + .003
Max.
± .010
± .025 ± .005
±.025
Nom.
Nom.SizeTo Edge
- .000
0
.216
.000
.112-40
PFHV440
.036.036 .203 .202.260
.080
.260.436 #1 .21
(#4-40) 1.316.095
0
.234
.000
.138-32
PFHV632
.036.036 .219 .218.276
.092
.290.484 #2 .23
(#6-32) 1.359.120
.164-32
0
.259
.000
PFHV832
.036.036 .252 .251.309
.111
.335.555 #2 .26
(#8-32) 1.371.106
All dimensions are in millimeters.
METRIC
Thread
ScrewA
Min.
Hole Size
Min. Dist.
Driver
T2
T1
HoleC/L
Size x
TypeThreadLength(Shank) Sheet
In SheetC E G H P Code
Max.
±
0.25
±
0.64
±
0.13
±0.64
Nom.
Nom.Size
Pitch
CodeMax. Thickness + 0.08
To Edge
0
5.55
0
M3 x 0.5
PFHV
M3
0.920.92 5.5 5.49 6.95
2.03
6.6911.25 #1
17.56 1.9
5.8
0
6.01
0
M3.5 x 0.6
PFHV M3.5
0.920.92 6 5.98 7.45
2.34
18.42 2.3
6.3
0
6.59
0
M4 x 0.7
PFHV
M4
0.920.92 6.4 6.38 7.85
2.79
1
9.39 2.7
7.4512.47 #2
8.514.1 #2 6.7
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
PennEngineering • www.pemnet.com
PF-9
PEM® TYPES PF7M™/PF7MF™ CAPTIVE PANEL SCREWS
• Small, compact and low-profile design for limited access areas.
•MAThread® anti cross-thread technology. (See page 4 for more information).
• Installs flush on back side of panel.
• Type PF7M Self-clinching mounting design provides high pushout resistance.
• Type PF7M does not require special hole preparation.
• Type PF7MF is appropriate for close centerline-to-edge applications.
• Type PF7MF does not require high installation force.
• Type PF7MF installs into any panel hardness.
• Available with Torx® recess.
Type PF7M
Type PF7MF
TYPE PF7M™ SELF-CLINCHING CAPTIVE PANEL SCREWS
Dimples on head
designate metric thread.
Phillips
driver size.
Patented.
(See chart)
E
H
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Retainer: Carbon Steel
Screw: Hardened Carbon Steel
Spring: 300 Series Stainless Steel
Finish:
Retainer: CN - Bright nickel over copper flash per ASTM B689
Screw: CN - Bright nickel over copper flash per ASTM B689
Spring: Natural Finish
For use in sheet hardness:
HRB 60 or less (Hardness Rockwell “B” Scale)
HB 107 or less (Hardness Brinell)
Shoulder
provides
positive
stop during
installation.
T2
T1
PART NUMBER DESIGNATION
PF7
P
C
A
M–632–0
CN
G
Clinching profile may vary.
Type
Anti
Thread
Cross-thread Size
Feature
Code
Length Finish
Code
Installation Data page 30. Performance Data page 37.
UNIFIED
All dimensions are in inches.
Type
Hole Size
Min.
FastenerScrew
A
Min.
In Sheet
Dist.
Thread
Thread
Material
Length (Shank) Sheet
+.003
C
E
H
G
P
T1T2 DriverHoleC/L
Size
Code
Code Max.Thickness–.000 Max.±.010±.010±.025±.025Nom.Nom.SizeTo Edge
Steel
.112-40
0
.210.000
PF7M440 .036 .036 .219 .218.280 .100
.380.550 #2 .28
(#4-40)
1
.270.065
0
.240.000
.138-32
PF7M632 .036 .036 .250 .249.310 .100
.410.610 #2 .29
(#6-32)
1 .300.065
0
.240.000
.164-32
PF7M832 .036 .036 .312 .311.370 .120
.430.630 #2 .33
(#8-32)
1 .300.065
METRIC
All dimensions are in millimeters.
Type
Min.
Thread FastenerScrew
A
Min.
Hole Size
Dist.
Thread
Size x
Length (Shank)
Sheet
In Sheet
C
E
H
G
P
T1T2 DriverHoleC/L
Material
Code
Pitch
Code Max.Thickness+0.08 Max.±0.25±0.25±0.64±0.64Nom.Nom.SizeTo Edge
Steel
0
5.330
9.6513.97 #2 7.11
M3 x 0.5
PF7MM3 0.92 0.92 5.565.547 2.5
1
6.861.65
0
6.10
10.9216 #28.38
M4 x 0.7
PF7MM4 0.92 0.92 7.92 7.99.4 3
1 7.621.65
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
PF-10 PennEngineering • www.pemnet.com
PEM® TYPE PF7M™/PF7MF™ CAPTIVE PANEL SCREWS
TYPE PF7MF™ FLARE-MOUNTED CAPTIVE PANEL SCREWS
Dimples on head
designate metric thread.
Phillips
driver size.
Patented.
(See chart)
E
H
Shoulder
provides
positive
stop during
installation.
T2
T1
G1
C
A
G2
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Retainer: Aluminum
Screw: Hardened Carbon Steel
Spring: 300 Series Stainless Steel
Spring: Natural Finish
Finish:
Retainer: Natural finish
Screw: CN - Bright nickel over copper flash per ASTM B689
PART NUMBER DESIGNATION
PF7
Type
M
F–632–0
Anti
Flaring Thread Length
Cross-thread
Size Code
Feature
Code
Installation Data page 30. Performance Data page 37.
UNIFIED
All dimensions are in inches.
Type
Hole Size
FastenerScrew
A
Min.
In Sheet
Thread
Thread
Material
Length (Shank) Sheet
+.005
C
E
H
G1G2T1T2Driver
Size
Code
CodeMax.
Thickness–.000 Max.±.010±.010±.025±.025Nom.Nom.Size
Steel
.112-40
0
.040.210
PF7MF 440 .041.031 .187 .186.280 .100
.380.550 #2
(#4-40)
1
.100.270
0
.040.240
.138-32
PF7MF 632 .072.060 .213 .212.310 .100
.410.610 #2
(#6-32)
1
.100
.300
0
.040.240
.164-32
PF7MF 832 .072.060 .266 .265.370 .120
.430.630 #2
(#8-32)
1
.100
.300
METRIC
All dimensions are in millimeters.
Type
Thread FastenerScrew
A
Min.
Hole Size
Thread
Size x
Length (Shank)
Sheet
In Sheet
C
E
H
G1G2T1T2Driver
Material
Code
Pitch
CodeMax.
Thickness+0.13 Max.±0.25±0.25±0.64±0.64Nom.Nom.Size
Steel
0
1.025.33
9.6513.97 #2
M3 x 0.5 PF7MFM3 1.050.79 4.75 4.73 7 2.5
1
2.546.86
0
1.026.1
M4 x 0.7 PF7MFM4 1.831.52 6.76 6.74 9.4 3
10.9216 #2
1
2.54
7.62
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
PennEngineering • www.pemnet.com
PF-11
PEM® TYPE PF30™/PF50™/PF60™ CAPTIVE PANEL SCREWS
• Low-profile design satisfies many functional and cosmetic requirements.
• Convenient large head for tool or finger operation.
• Types PF50/PF60 are available with Torx® recess.
• Types PF50/PF60 are available with MAThread® anti cross-thread
technology. (See page 4 for more information).
Type PF30
Knurled Cap
TYPE PF30™ LOW-PROFILE CAPTIVE PANEL SCREWS
T2
Type PF60
Smooth Cap
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Finish:
Retainer:CN - Bright nickel over copper flash per ASTM B689
Screw:CN - Bright nickel over copper flash per ASTM B689
Spring: Natural Finish
Optional Finish:
Retainer: BN - Black nitride, AMS2753, Section 3
Screw: BN - Black nitride, AMS2753, Section 3
E
Shoulder
provides
positive
stop during
installation.
Knurled Cap
Material:
Retainer: Carbon Steel
Screw:Hardened Carbon Steel (#4-40 and M3 sizes only)
Carbon Steel (all other sizes)
Spring: 300 Series Stainless Steel
Diagonal knurl and
groove on retainer
identifies metric
thread sizes.
Available with
DuraBlackTM finish
(Finish Code “BN”)
Type PF50
H
For use in sheet hardness:
HRB 60 or less (Hardness Rockwell “B” Scale)
HB 107 or less (Hardness Brinell)
T1
PART NUMBER DESIGNATION
C
PF30–832– 30
G
A
CN
Clinching profile may vary.
Installation Data page 31. Performance Data page 38.
Type and
Shank Code
UNIFIED
All dimensions are in inches.
Thread Size
Screw
Finish
Code
Length Code Code
Thread
Size
Type
Thread
Code
Screw
Length
Code
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ .003
- .000
C
Max.
E
±.010
G
± .015
H
± .005
T1
Max.
T2
Nom.
Min. Dist.
HoleC/L
To Edge
.112-40
(#4-40)
PF30
PF31
PF32
440
30
.030
.038
.058
.030
.040
.060
.203
.202
.406
.300
.202
.325
.595
.26
.138-32
(#6-32)
PF30
PF31
PF32
632
30
.030
.038
.058
.030
.040
.060
.219
.218
.438
.300
.202
.325
.595
.28
.164-32
(#8-32)
PF30
PF31
PF32
832
30
.030
.038
.058
.030
.040
.060
.250
.249
.468
.300
.207
.330
.600
.29
.190-32
(#10-32)
PF30
PF31
PF32
032
30
.030
.038
.058
.030
.040
.060
.312
.311
.530
.300
.220
.335
.605
.33
.250-20
(1/4-20)
PF32
0420
35
.058
.060
.375
.374
.625
.350
.242
.385
.675
.38
METRIC
All dimensions are in millimeters.
Thread
Size x
Pitch
Type
Thread
Code
Screw
Length
Code
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ 0.08
C
Max.
E
±0.25
G
± 0.4
H
± 0.13
T1
Max.
T2
Nom.
Min. Dist.
HoleC/L
To Edge
M3 x 0.5
PF31
PF32
M3
30
0.97
1.48
1
1.5
5.5
5.48
10.31
7.62
5.13
8.26
15.11
6.6
M4 x 0.7
PF31
PF32
M4
30
0.97
1.48
1
1.5
6.4
6.38
11.89
7.62
5.26
8.38
15.24
7.37
M5 x 0.8
PF31
PF32
M5
30
0.97
1.48
1
1.5
8
7.98
13.46
7.62
5.59
8.51
15.37
8.38
M6 x 1
PF32
M6
35
1.48
1.5
9.5
9.48
15.88
8.89
6.12
9.78
17.15
9.65
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
PF-12 PennEngineering • www.pemnet.com
PEM® TYPE PF30™/PF50™/PF60™ CAPTIVE PANEL SCREWS
TYPE PF50™ AND PF60™ LOW-PROFILE CAPTIVE
PANEL SCREWS
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Knob: Carbon Steel
Screw: Carbon Steel
Groove on retainer and dimples on
head designate metric thread.
Retainer: Carbon Steel
Spring: 300 Series Stainless Steel
Finish:
Knob: CN - Bright nickel over copper flash per ASTM B689
Retainer:CN - Bright nickel over copper flash per ASTM B689
Screw:CN - Bright nickel over copper flash per ASTM B689
Spring: Natural Finish
Available with
DuraBlackTM finish
(Finish Code “BN”)
Phillips
driver size.
Optional Finish:
Knob: BN - Black Nitride, AMS2753, Section 3
Retainer: BN - Black Nitride, AMS2753, Section 3
Screw:BN - Black Nitride, AMS2753, Section 3
(See chart)
E
Shoulder
provides
positive
stop during
installation.
T2
H
For use in sheet hardness:
HRB 60 or less (Hardness Rockwell “B” Scale)
HB 107 or less (Hardness Brinell)
T1
PART NUMBER DESIGNATION
C
P
PF50–440– 1
PF60–440– 1
G
A
CN
CN
Clinching profile may vary.
Installation Data page 31. Performance Data page 39.
All dimensions are in inches.
Type
Thread
Knurled
Smooth
Size
Cap
Cap
PF50
PF60
UNIFIED
.112-40
(#4-40)
.138-32
(#6-32)
.164-32
(#8-32)
.190-32
(#10-32)
.250-20
(1/4-20)
PF51
PF61
Thread
Code
440
440
PF52
PF62
440
PF50
PF60
632
PF51
PF61
632
PF52
PF62
632
PF50
PF60
832
PF51
PF61
832
PF52
PF62
832
PF50
PF60
032
PF51
PF61
032
PF52
PF62
032
PF52
PF62
0420
Type and
Shank Code
Screw
Length
Code
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
A
(Shank)
Max.
.030
Min.
Sheet
Thickness
.030
Hole Size
In Sheet
+ .003 -.000
.203
C
Max.
.202
E
+.015
–.005
.406
.038
.040
.203
.202
.406
Screw
Length
Code
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
.058
.060
.203
.202
.406
.030
.030
.219
.218
.438
.038
.040
.219
.218
.438
.058
.060
.219
.218
.438
.030
.030
.250
.249
.468
.038
.040
.250
.249
.468
.058
.060
.250
.249
.468
.030
.030
.312
.311
.530
.038
.040
.312
.311
.530
.058
.060
.312
.311
.530
.058
.060
.375
.374
.625
A
(Shank)
Max.
0.77
Min.
Sheet
Thickness
0.8
Hole Size
In Sheet
+ 0.08
5.5
C
Max.
5.48
E
+0.4
–0.13
10.3
0.97
1
5.5
5.48
10.3
G
±.025
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.230
.290
.280
.340
H
±.008
.207
G
±0.64
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
5.84
7.37
7.11
8.64
H
±0.2
5.26
.207
.207
.207
.207
.207
.217
.217
.217
.225
.225
.225
.246
Thread Size
Screw
Finish
Code
Length Code Code
P
±.025
.000
.060
.000
.052
.000
.032
.000
.060
.000
.052
.000
.032
.000
.060
.000
.052
.000
.032
.000
.060
.000
.052
.000
.032
.000
.060
T1
Max.
.340
T2
Nom.
.520
Driver
Size
#1
Min. Dist
HoleC/L
To Edge
.26
.340
.520
#1
.26
.340
.520
#1
.26
.340
.520
#2
.28
.340
.520
#2
.28
.340
.520
#2
.28
.340
.520
#2
.29
.340
.520
#2
.29
.340
.520
#2
.29
.340
.530
#2
.33
.340
.530
#2
.33
.340
.530
#2
.33
.395
.600
#2
.38
T1
Max.
8.64
T2
Nom.
13.21
Driver
Size
#1
Min. Dist
HoleC/L
To Edge
6.6
8.64
13.21
#1
6.6
All dimensions are in millimeters.
Thread
Size x
Pitch
METRIC
M3 x 0.5
M3.5 x 0.6
M4 x 0.7
M5 x 0.8
M6 x 1
Type
Knurled
Smooth
Cap
Cap
PF50
PF60
PF51
PF61
Thread
Code
M3
M3
PF52
PF62
M3
PF50
PF60
M3.5
PF51
PF61
M3.5
PF52
PF62
M3.5
PF50
PF60
M4
PF51
PF61
M4
PF52
PF62
M4
PF50
PF60
M5
PF51
PF61
M5
PF52
PF62
M5
PF52
PF62
M6
1.48
1.5
5.5
5.48
10.3
0.77
0.8
5.56
5.54
11.1
0.97
1
5.56
5.54
11.1
1.48
1.5
5.56
5.54
11.1
0.77
0.8
6.4
6.38
11.9
0.97
1
6.4
6.38
11.9
1.48
1.5
6.4
6.38
11.9
0.77
0.8
8
7.98
13.5
0.97
1
8
7.98
13.5
1.48
1.5
8
7.98
13.5
1.48
1.5
9.5
9.48
15.9
5.26
5.26
5.26
5.26
5.26
5.51
5.51
5.51
5.72
5.72
5.72
6.25
P
±0.64
0
1.52
0
1.32
0
0.81
0
1.52
0
1.32
0
0.81
0
1.52
0
1.32
0
0.81
0
1.52
0
1.32
0
0.81
0
1.52
8.64
13.21
#1
6.6
8.64
13.21
#2
7.1
8.64
13.21
#2
7.1
8.64
13.21
#2
7.1
8.64
13.46
#2
7.4
8.64
13.46
#2
7.4
8.64
13.46
#2
7.4
8.64
13.46
#2
8.4
8.64
13.46
#2
8.4
8.64
13.46
#2
8.4
10.04
15.24
#2
9.7
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
PennEngineering • www.pemnet.com
PF-13
PEM® TYPES PFC4™/PFC2P™CAPTIVE PANEL SCREWS
• Types PFC4/PFC2P have fully concealed-head for tool only access.
• Types PFC4/PFC2P comply with UL 60950 standards.
• Type PFC4 installs into stainless steel sheets HRB 88 or less.
• Types PFC4/PFC2P are available with MAThread® anti cross-thread
technology. (See page 4 for more information).
• Types PFC4/PFC2P available with Torx® recess.
Type PFC4
Type PFC2P
TYPE PFC4™ RECESSED-HEAD CAPTIVE PANEL SCREWS
O
INT
LLS STEEL
A
T
INS LESS
IN
STA
Phillips
driver size.
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g
Dimples on head
designates metric
thread.
Material:
Retainer: 400 Series Stainless Steel
Screw: 400 Series Stainless Steel
Spring: 300 Series Stainless Steel
Retaining Ring: Nylon, temperature limit 200˚ F / 93˚ C
(See chart)
E
Shoulder
provides
positive
stop during
installation.
Finish:
Retainer:Passivated and/or tested per ASTM A380
Screw:Passivated and/or tested per ASTM A380
Spring: Natural Finish
T2
For use in sheet hardness:
HRB 88 or less (Hardness Rockwell “B” Scale)
HB 183 or less (Hardness Brinell)
T1
P
G
PEM
Trademark
Blue plastic
retaining ring.
PART NUMBER DESIGNATION
PFC4–832– 50
A
C
Clinching profile may vary.
Type and
Material
Installation Data page 32. Performance Data page 39.
Thread Size
Code
Screw Length
Code
UNIFIED
All dimensions are in inches.
Thread
Size
Type
Thread
Code
.112-40
(#4-40)
PFC4
440
.138-32
(#6-32)
PFC4
632
.164-32
(#8-32)
PFC4
832
.190-32
(#10-32)
PFC4
032
Screw
Length
Code
40
62
40
62
84
50
72
94
50
72
94
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ .003
- .000
C
Max.
E
± .010
.060
.060
.265
.264
.344
.060
.060
.281
.280
.375
.060
.060
.312
.311
.406
.060
.060
.344
.343
.437
C
Max.
E
± 0.25
G
± .016
P
±.025
.250
.375
.250
.375
.500
.312
.437
.562
.312
.437
.562
.000
.125
.000
.125
.250
.000
.125
.250
.000
.125
.250
G
± 0.4
P
±0.64
6.4
9.5
7.9
11.1
14.3
7.9
11.1
14.3
0
3.2
0
3.2
6.4
0
3.2
6.4
T1
Max.
T2
Nom.
Driver
Size
Min. Dist.
HoleC/L
To Edge
.370
.540
#1
.25
.380
.540
#2
.28
.480
.705
#2
.31
.490
.705
#2
.34
T1
Max.
T2
Nom.
Driver
Size
Min. Dist
HoleC/L
To Edge
9.4
13.72
#1
6.35
12.19
17.91
#2
7.87
12.45
17.91
#2
8.63
METRIC
All dimensions are in millimeters.
Thread
Size
x Pitch
Type
Thread
Code
M3 x 0.5
PFC4
M3
M4 x 0.7
PFC4
M4
M5 x 0.8
PFC4
M5
Screw
Length
Code
40
62
50
72
94
50
72
94
A
(Shank)
Max.
Min.
Hole Size
Sheet
In Sheet
Thickness
+ 0.08
1.53
1.53
6.73
6.71
8.74
1.53
1.53
7.92
7.9
10.31
1.53
1.53
8.74
8.72
11.1
A NOTE ABOUT FASTENERS FOR STAINLESS STEEL PANELS
In order for self-clinching fasteners to work properly, the fastener must be harder than the sheet into which it is being installed. In the case of stainless steel panels,
fasteners made from 300 Series Stainless Steel do not meet this hardness criteria. It is for this reason that 400 series fasteners are offered (Type PFC4). However,
while these 400 Series fasteners install and perform well in 300 Series stainless sheets they should not be used if the end product:
• Will be exposed to any appreciable corrosive presence.
• Requires non-magnetic fasteners.
• Will be exposed to any temperatures above 300˚F (149˚C)
If any of the these are issues, please contact techsupport@pemnet.com for other options.
PF-14 PennEngineering • www.pemnet.com
PEM® TYPE PFC4™/PFC2P™ CAPTIVE PANEL SCREWS
TYPE PFC2P™ RECESSED-HEAD CAPTIVE PANEL SCREWS
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g
Phillips
driver size.
Material:
Retainer: 300 Series Stainless Steel
Screw: 400 Series Stainless Steel
Spring: 300 Series Stainless Steel
Retaining Ring: Nylon, temperature limit 200˚ F / 93˚ C
(See chart)
Available with
DuraBlackTM finish
(Finish Code “BN”)
Dimples on
head designates
metric thread.
E
Shoulder
provides
positive
stop during
installation.
Finish:
Retainer:Passivated and/or tested per ASTM A380
Screw:Passivated and/or tested per ASTM A380
Spring: Natural Finish
Optional Finish:
Retainer:BN - Black nitride, AMS2753, Section 3
Screw:BN - Black nitride, AMS2753, Section 3
T2
T1
P
PEM
Trademark
Blue plastic
retaining ring.
G
For use in sheet hardness:
HRB 70 or less (Hardness Rockwell “B” Scale)
HB 125 or less (Hardness Brinell)
PART NUMBER DESIGNATION
PFC2P– 832–50
A
C
Clinching profile may vary.
Installation Data page 32. Performance Data page 39.
Type and
Material
UNIFIED
All dimensions are in inches.
Thread Size
Screw
Code
Length Code
Thread
Size
Type
Thread
Code
Screw
Length
Code
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ .003
- .000
C
Max.
E
± .010
G
± .016
P
±.025
T1
Max.
T2
Nom.
Driver
Size
Min. Dist.
HoleC/L
To Edge
.112-40
(#4-40)
PFC2P
440
40
62
.060
.060
.265
.264
.312
.250
.375
.000
.125
.370
.540
#1
.25
.138-32
(#6-32)
PFC2P
632
40
62
84
.060
.060
.281
.280
.344
.250
.375
.500
.000
.125
.250
.380
.540
#2
.28
.164-32
(#8-32)
PFC2P
832
50
72
94
.060
.060
.312
.311
.375
.312
.437
.562
.000
.125
.250
.480
.705
#2
.31
.190-32
(#10-32)
PFC2P
032
50
72
94
.060
.060
.344
.343
.406
.312
.437
.562
.000
.125
.250
.490
.705
#2
.34
.250-20
(1/4-20)
PFC2P
0420
60
82
04
.060
.060
.413
.412
.468
.375
.500
.625
.000
.125
.250
.620
.905
#3
.38
C
Max.
E
± 0.25
G
± 0.4
P
±0.64
T1
Max.
T2
Nom.
Driver
Size
Min. Dist
HoleC/L
To Edge
METRIC
All dimensions are in millimeters.
Thread
Size x
Pitch
Type
Thread
Code
Screw
Length
Code
A
(Shank)
Max.
Min.
Hole Size
Sheet
In Sheet
Thickness
+ 0.08
M3 x 0.5
PFC2P
M3
40
62
1.53
1.53
6.73
6.71
7.92
6.4
9.5
0
3.2
9.4
13.72
#1
6.35
M4 x 0.7
PFC2P
M4
50
72
94
1.53
1.53
7.92
7.9
9.53
7.9
11.1
14.3
0
3.2
6.4
12.19
17.91
#2
7.87
M5 x 0.8
PFC2P
M5
50
72
94
1.53
1.53
8.74
8.72
10.31
7.9
11.1
14.3
0
3.2
6.4
12.45
17.91
#2
8.63
M6 x 1
PFC2P
M6
60
82
04
1.53
1.53
10.49
10.47
11.89
9.5
12.7
15.9
0
3.2
6.4
15.75
22.99
#3
9.65
PennEngineering • www.pemnet.com
PF-15
PEM® TYPES PFC2/PFS2 CAPTIVE PANEL SCREWS
• Types PFC2/PFS2 are for tool or finger operation.
TYPE PFC2
Type PFC2/PFS2
Available with
DuraBlackTM finish
(Finish Code “BN”)
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g
Material:
Retainer: 300 Series Stainless Steel (2)
Screw: 300 Series Stainless Steel
Spring: 300 Series Stainless Steel
Retaining Ring: Nylon, temperature limit 200˚ F / 93˚ C
Finish:
Retainer:Passivated and/or tested per ASTM A380
Screw:Passivated and/or tested per ASTM A380
Spring: Natural Finish
Optional Finish:
Retainer: BN - Black nitride, AMS2753, Section 3
Screw: BN - Black nitride, AMS2753, Section 3
For use in sheet hardness:
HRB 70 or less (Hardness Rockwell “B” Scale)
HB 125 or less (Hardness Brinell)
Diagonal knurl identifies
metric thread sizes.
E
Shoulder
provides
positive
stop during
installation.
PFC2–832–50
PFS2–832–50
T1
G
PEM Trademark
Blue plastic
retaining ring
Type and
Material
Thread Size
Code
A
C
All dimensions are in inches.
UNIFIED
PART NUMBER DESIGNATION
H
T2
P
Thread
Size
TYPE PFS2
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Retainer: Hardened Carbon Steel (2)
Screw: Carbon Steel
Spring: 300 Series Stainless Steel
Retaining Ring: Nylon, temperature limit 200˚ F / 93˚ C
Finish:
Retainer:CN - Bright nickel over copper flash per ASTM B689
Screw:CN - Bright nickel over copper flash per ASTM B689
Spring: Natural Finish
Optional Finish:
Retainer: BN - Black nitride, AMS2753, Section 3
Screw: BN - Black nitride, AMS2753, Section 3
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale)
HB 150 or less (Hardness Brinell)
Type
Stainless
Steel
Steel
.112-40
(#4-40)
PFC2
PFS2
440
.138-32
(#6-32)
PFC2
PFS2
632
.164-32
(#8-32)
PFC2
PFS2
832
.190-32
(#10-32)
PFC2
PFS2
032
.250-20
(1/4-20)
PFC2
PFS2
0420
Screw
Length
Code
40
62
40
62
84
50
72
94
50
72
94
60
82
04
Screw Finish
Length Code
Code
Installation Data page 33. Performance Data page 39.
Clinching profile may vary.
Thread
Code
CN
Hole Size
A
Min.
In Sheet
(Shank)
Sheet
+ .003
Max. Thickness
- .000
C
Max.
E
± .010
.060
.060
.265
.264
.312
.060
.060
.281
.280
.344
.060
.060
.312
.311
.375
.060
.060
.344
.343
.406
.060
.060
.413
.412
.468
C
Max.
E
±.25
G
±.016
.250
.375
.250
.375
.500
.312
.437
.562
.312
.437
.562
.375
.500
.625
H
±.005
.072
.072
.082
.082
.097
P
±.025
.000
.125
.000
.125
.250
.000
.125
.250
.000
.125
.250
.000
.125
.250
T1
Max.
T2
Nom.
Min. Dist.
HoleC/L
To Edge
.360
.540
.25
.360
.540
.28
.450
.690
.31
.450
.690
.34
.580
.880
.38
T1
Max.
T2
Nom.
Min. Dist.
HoleC/L
To Edge
9.14
13.72
6.35
11.43
17.53
7.87
11.47
17.53
8.63
14.73
22.35
9.65
All dimensions are in millimeters.
METRIC
Thread
Size x
Pitch
Type
Thread
Code
Stainless
Steel
Steel
M3 x 0.5
PFC2
PFS2
M3
M4 x 0.7
PFC2
PFS2
M4
M5 x 0.8
PFC2
PFS2
M5
M6 x 1
PFC2
PFS2
M6
Screw
Length
Code
40
62
50
72
94
50
72
94
60
82
04
A
Min.
Hole Size
(Shank)
Sheet
In Sheet
Max. Thickness + 0.08
1.53
1.53
6.73
6.71
7.92
1.53
1.53
7.92
7.9
9.53
1.53
1.53
8.74
8.72
10.31
1.53
1.53
10.49
10.47
11.89
G
± 0.4
6.4
9.5
7.9
11.1
14.3
7.9
11.1
14.3
9.5
12.7
15.9
H
± 0.13
1.83
2.08
2.08
2.46
P
±0.64
0
3.2
0
3.2
6.4
0
3.2
6.4
0
3.2
6.4
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) The blue plastic retaining rings are a PEM trademark. The temperature limit is 200° F / 93° C.
PF-16 PennEngineering • www.pemnet.com
PEM® TYPES PTL2/PSL2 SPRING-LOADED PLUNGER ASSEMBLIES
• Used as positioning pins for sliding components such as drawer slides and equipment consoles.
• Fast installation and removal of components.
• Reverse side of sheet is flush when plunger is retracted.
• Type PTL2 has quick lockout feature to hold plunger in fully retracted position.
• For use in sheets of HRB 80 or less.
• Available as Type PSL2 without lockout feature on special order.
Material:
Plunger: Hardened Carbon Steel
Retainer: Hardened Carbon Steel
Type PTL2/PSL2
installed and with
mating panel.
Finish:
Plunger: CN - Bright nickel over copper flash per ASTM B689
Retainer: CN - Bright nickel over copper flash per ASTM B689
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale)
HB 150 or less (Hardness Brinell)
E1
Lockout feature holds
plunger in retracted
position. Simply
retract and twist
to engage lockout
feature.
Shoulder
provides
positive
stop during
installation.
T2
H
PART NUMBER DESIGNATION
T1
PTL2– 04–4
E2
C
G
A
Clinching profile may vary.
Type
Plunger
Diameter
Code
D
CN
Plunger Finish
Length Code
Code
Installation Data page 33. Performance Data page 39.
UNIFIED
All dimensions are in inches.
Type
Plunger
Diameter
Code
Plunger
Length
Code
A
(Shank)
Max.
Min.
Hole Size
Sheet
In Sheet
Thickness +.003 -.000
C
Max.
D
+ .000
- .005
E1
± .010
E2
± .010
G
± .010
H
± .010
T1
± .010
T2
Nom.
Min. Dist.
HoleC/L
To Edge
PTL2
04
4
.058
.060
.328
.327
.250
.50
.406
.310
.17
.595
.895
.34
PSL2 (1)
04
4
.058
.060
.328
.327
.250
.50
.406
.310
.17
.510
.780
.34
METRIC
All dimensions are in millimeters.
Type
Plunger
Diameter
Code
Plunger
Length
Code
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ 0.08
C
Max.
D
- 0.13
E1
± 0.25
E2
± 0.25
G
± 0.25
H
± 0.25
T1
± 0.25
T2
Nom.
Min. Dist.
HoleC/L
To Edge
PTL2
04
4
1.47
1.53
8.33
8.31
6.35
12.7
10.3
7.87
4.32
15.11
22.73
8.64
PSL2 (1)
04
4
1.47
1.53
8.33
8.31
6.35
12.7
10.3
7.87
4.32
12.95
19.81
8.64
(1) Without lockout feature. Available on special order.
PennEngineering • www.pemnet.com
PF-17
PEM® TYPES SCBR™/SCB™/SCBJ™ CAPTIVE PANEL SCREWS
• Permanently captivates into sheets as thin as .040” / 1.02 mm and greater.
• Lowest cost captive screw design to replace loose hardware.
• Available with self-retracting (Type SCBR), axial float (Type SCB), or
jacking feature (Type SCBJ).
• Appropriate for close centerline-to-edge applications.
Type SCB
Type SCBR
Type SCBJ
TYPE SCBR™ SPINNING CLINCH BOLT WITH SELF-RETRACTING FEATURE
Type SCBR retracted
Type SCBR engaged
Phillips
driver size.
(See chart)
E
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Screw - Hardened Carbon Steel
Spring - 300 series stainless steel
H2
H1
L
Finish:
Screw - ZI - Zinc plated, 5µm, colorless (standard) (2)
Spring: Natural Finish
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale)
HB 150 or less (Hardness Brinell)
PART NUMBER DESIGNATION
SCBR–632– 8
T
Installation Data page 34. Performance Data page 40.
Type
Thread
Size
Code
UNIFIED
All dimensions are in inches.
Length Code “L” ±.015
Thread
Thread (Length Code in 16ths of an inch)
Size Type Code
.500
.112-40
SCBR440
8
(#4-40)
.138-32
SCBR632
8
(#6-32)
.164-32
SCBR832
8
(#8-32)
Min.
Hole Size
Sheet
in Sheet
Thickness +.003 –.000
ZI
Length Finish
Code
E
Min. Dist
T DriverHole C/L
+.005
H1H2
–.010
±.005
Ref.
Nom.
Size To Edge
.040
.112
.348.165.495.130#1.175
.040
.138
.381.170.500.130#2.190
.040
.164
.410.175.505.130#2.205
METRIC
All dimensions are in millimeters.
Thread
Length Code “L” ±0.4
Size x
Thread
Pitch
Type
Code
(Length Code in millimeters)
M3 x 0.5
SCBR
M3
M4 x 0.7
SCBRM4
Min.
Sheet
Thickness
Hole Size
in Sheet
+0.08
E
Min. Dist
+0.13
H1H2
T DriverHole C/L
–0.25
±0.13
Ref.
Nom.
Size
To Edge
12
1.02
3
9.1
12
1.02
4
10.7 4.512.13.3 #2 5.4
4.2
11.8
3.3
#1
4.5
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
NOTE: Type SCBR screws are shipped with mating springs.
For designs requiring a specific spring rate, contact our PEM Technical Support group at techsupport@pemnet.com.
PF-18 PennEngineering • www.pemnet.com
PEM® TYPES SCBR™/SCB™/SCBJ™ CAPTIVE PANEL SCREWS
TYPES SCB™/SCBJ™ SPINNING CLINCH BOLTS
Type SCB with
axial float.
Type SCBJ with
jacking feature.
Type SCBJ
Phillips
driver size.
T
(See chart)
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Hardened Carbon Steel
L
H
Finish:
ZI - Zinc plated, 5µm, colorless (standard) (2)
E
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale)
HB 150 or less (Hardness Brinell)
Type SCB
Phillips
driver size.
T
(See chart)
PART NUMBER DESIGNATION
SCB
L
Type
E
H
J– 632–6
Jacking Thread
Size
Code
(If applicable)
Installation Data page 34. Performance Data page 40.
ZI
Length Finish
Code
All dimensions are in inches.
UNIFIED
Thread
Size
Type
Thread
Jacking Non-jacking Code
.112-40
(#4-40)
SCBJ
—
—
SCB
.138-32
(#6-32)
SCBJ
—
—
SCB
440
632
Length Code “L” ±.015
(Length Code in 16ths of an inch)
.250
.375
.500
4
6
8
—
—
8
4
6
8
—
—
8
Min.
Hole Size
Sheet
in Sheet
E
Thickness +.003 –.000 ±.010
H
Nom.
–4
T
Nom.
Min. Dist.
Nom. Axial
Driver HoleC/L
Float
Size
To Edge
– 6– 8
.040
.112
.250
.160
.080
—
.285.410
—
#1
— .130.330
.040
.138
.291
.160
.080
—
.285.410
Hole Size
in Sheet
+0.08
E
±0.25
H
Nom.
T Nom. 1.02
3
1.02
4
—
#2
— .130.330
.13
.15
METRIC
All dimensions are in millimeters.
Thread
Size x
Pitch
M3 x 0.5
M4 x 0.7
Type
Thread
Jacking Non-jacking Code
SCBJ
—
—
SCB
SCBJ
—
—
SCB
M3
M4
Min.
Length Code “L”
±0.4
Sheet
(Length Code in millimeters)
Thickness
6
10
1214
—
—
1214
6
10
1214
—
—
1214
–6
–10
6.6
3.7
2.03
—
7.7
8.28
3.7
2.03
—
7.7
—
—
–12-14
Nom.
Min. Dist.
Axial Driver HoleC/L
Float Size
To Edge
9.7 11.7
—
#1
3.3
5.3
7.67
3.3
9.7 11.7
—
#2
3.3
5.3
7.67
5
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) See PEM Technical Support section of our web site for related plating standards and specifications.
PennEngineering • www.pemnet.com
PF-19
PEM® HEAT SINK MOUNTING SYSTEM
The new HSCB engineered mounting system provides secure attachment of a heat sink to the circuit board while providing firm
contact to the chip component allowing optimum heat dissipation. The three-piece fastening system, sold individually, includes
the screw, spring and receptacle nut. The clamp load created is
determined by the spring rate and the amount of deflection that is
designed into the joint of the hardware. The system also allows for
slight expansion and contraction of the joint components without
stress to the delicate circuitry. The unique “click” feature lets the
user know when the fastener is completely installed.
NEW
!
G
Type HSR
To select proper length code of nut/standoff:
Patent pending
Type HSL
1) Determine “G”, the distance from the top surface of the heat sink to
the top of the P.C. Board.
2) Find the combination of Screw (HSCB) and Nut (HSR) whose sum of
Screw Factor (SF) plus Nut Factor (NF) are closest to G.
3) Find D = G – SF – NF. The D value must be a negative number
between zero and 1mm or 1/32” (1 dash length of HSR nut).
4) The actual working load is equal to the Spring (HSL) Working Load
+ (D x spring rate k). Lower D value results in lower force.
Type HSCB
• Screw can not be overtightened. Audible “click” when fully
engaged.
•Screw and spring mount together permanently into the
heat sink.
• Spring determines clamp force.
• Receptacle nut mounts permanently to the PC board.
• Provides even, constant contact of heat sink to chip
component.
• Allows removal of heat sink if desired.
If this or any standard product does not meet your
application needs, contact our PEM Technical Support
group at techsupport@pemnet.com to develop a special
product that matches your specific application.
TYPE HSCB™ SELF-CAPTIVATING SCREW
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Hardened carbon steel
Phillips
driver size.
(See chart)
Finish:
Screw - ZI - Zinc plated, 5µm, colorless (2)
ES
For use in sheet hardness:
HRB 80 / HB150 or less (3)
H2
PART NUMBER DESIGNATION
H1
HSCB– 440–4
ZI
L
TS
Type
Installation Data page 35.
Performance Data page 40.
Thread
Size
Code
Length
Code
Finish
Code
UNIFIED
All dimensions are in inches.
Min.
Hole Size
Screw
Min. Dist
Length Code “L” ±.015
TS FactorDriverHoleC/L
Thread
Thread
Sheet
in Sheet
ESH1H2
Size
Type
Code
.320
Thickness +.003 –.000 ±.010
Ref.
Ref.
Min.
(SF)
Size
To Edge
.112-40
HSCB440
4
.040 .112 .312.300 .470.130.170#1 .156
(#4-40)
.138-32
HSCB632
4
.040 .138 .352.300 .470.130.170#2 .178
(#6-32)
METRIC
All dimensions are in millimeters.
Thread
Length Code “L” ±0.4
Size x
Thread
Pitch
Type
Code
8.13
M3 x 0.5
HSCB
M3
3
Min.
Sheet
Thickness
1
Hole Size
TS
in Sheet
ESH1H2
+0.08
±0.25
Ref.
Ref.
Min.
3
8.18
7.67
12
3.3
Screw
Min. Dist
FactorDriver HoleC/L
(SF)
Size
To Edge
4.32
#1
4.13
NOTE:HSCB screws, HSR nuts and HSL springs are sold separately.
(1) As with all Class 2A/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be
gauged to Class 3A/4h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2.
(2) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
(3) HRB - Hardness Rockwell “B” Scale. HB - Hardness Brinell.
PF-20 PennEngineering • www.pemnet.com
PEM® HEAT SINK MOUNTING SYSTEM
TYPE HSR™ BROACHING NUT/STANDOFF
Threads:
Internal, ASME B1.1, 2B / ASME B1.13M, 6H
Material:
Carbon steel
F
Finish:
ET - Electro-plated tin ASTM B 545, class B with clear preservative coating, annealed (1)
For use in sheet hardness:
HRB 60 / HB 107 or less (2)
C
PART NUMBER DESIGNATION
HSR–
440–2
A
TN
ET
EN
Type
Installation Data page 35. Performance Data page 40.
Thread
Size
Code
Length
Code
Finish
Code
UNIFIED
All dimensions are in inches.
A
Min.
Hole Size
Nut
Min. Dist.
Thread
Thread
Length
(Shank)
Sheet
In Sheet
C
ENFTN FactorHoleC/L
Size Type Code Code Max. Thickness
+.003 –.000
±.003±.005±.010±.005(NF)To Edge
.112-40
2
.065.000
HSR440
.060.060 .166 .184.219.060
0.17
(#4-40)
3
.093
.031
.138-32
2
.065.000
HSR632
.060.060 .213 .231.281.060
0.22
(#6-32)
3
.093
.031
METRIC
All dimensions are in millimeters.
Thread
A
Min.
Hole Size
Nut
Min. Dist.
Size x
Thread
Length
(Shank)
Sheet
In Sheet
C
EN FTN FactorHoleC/L
Pitch Type Code Code Max. Thickness
+0.08±0.08±0.13±0.25±0.13(NF)
To Edge
2
2.75
M3 x 0.5
HSR
M3
1.531.534.224.685.56 1.3
4.4
33
1.75
NOTE:HSCB screws, HSR nuts and HSL springs are sold separately.
(1) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
(2) HRB - Hardness Rockwell “B” Scale. HB - Hardness Brinell.
Spring I.D.
Min.
TYPE HSL™ SPRINGS
HSL springs are engineered to provide a reliable and repeatable spring rate when
assembled with mating PEM hardware. The spring rate is critical to the successful
assembly of your heat sink. Clamp load will be determined by the spring rate and
deflection that is designed into the joint.
Minimum
Load at
Inside Dia.
Working Height ±10%
Part
Number (in.) (mm) (lbs.)
(N)
Working
Height Ref.
Spring Rate
k
(in.) (mm) (lb/in)(N/mm)
Spring
Material
Working Height
17-7 Stainless Steel,
HSL-574-35 .226 5.74 7.87
35 .2706.86 74 12.96
Natural Finish
HSL-701-35 .276 7.01 7.87
35 .2706.86 39 6.8417-7 Stainless Steel,
Natural Finish
NOTE:HSCB screws, HSR nuts and HSL springs are sold separately. HSL-574-35 spring fits
screw thread sizes #4-40 and M3 and HSL-701-35 spring fits screw thread size #6-32.
The HSL Inside Diameter Code is expressed in hundredths of millimeters.
Example “574” indicates a minimum inside diameter of 5.74mm or .226”.
The HSL Load Code is expressed in Newtons developed at the working height of the spring
once the joint is assembled.
Example “35” indicates working load of 35 Newtons, or approximately 8 lbs.
For designs requiring a specific spring rate, contact our PEM Technical Support group at
techsupport@pemnet.com
PART NUMBER DESIGNATION
HSL–
574–35
Type
Inside
Diameter
Code
Load
Code
PennEngineering • www.pemnet.com
PF-21
PEM® TYPE PF10 FLUSH-MOUNTED CAPTIVE PANEL SCREWS
•Type PS10 screw head is flush in sheets as thin as .125” / 3.2mm.
•Type PS10 screw remains captive in retainer when disengaged.
•Type PR10 retainer and F10 receptacle nut is for use in sheets of HRB 70 or less.
•Type N10 nut is for use in sheets of HRB 80 or less.
• Complies with UL 60950 standards.
PS10 Screw
M
B
G
T
PR10 A
Retainer
P
N10 Receptical Nut
Manually
Retracted
Position
PR10 Retainer
PS10 Screw
N10
Receptacle
Nut
Installation Data page 36. Performance Data page 41.
Floating Receptacle Nuts
UNIFIED
All dimensions are in inches.
A
Min.
.04.125.40.16.28.13
Type F Fasteners as retainers
All dimensions are in millimeters.
METRIC
Available on special order
Type F10 self-clinching
floating receptacle nuts
permit a minimum of
.015”/0.38mm adjustment for
mating hole misalignment.
B
G
T
MP
Nom. ± .010
Nom.
A
Min.
B
G
T
MP
Nom. ± 0.25
Nom.
For applications where the
screw head may project
above the sheet surface,
PS10 screws may be used
with PEMSERT® Type F
fasteners as retainers. For
dimensions and engineering
data on Type F fasteners, see
PEM Bulletin F.
1 3.1810.164.06 7.11 3.3
PS10 FLUSH MOUNTED SCREWS
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g
Material:
300 Series Stainless Steel
E
Diagonal knurl
identifies metric
thread sizes.
PS10 Screw
Finish:
Passivated and/or tested per ASTM A380
H
PART NUMBER DESIGNATION
PS10–832–40
L
T
Thread Size
Code
Screw
Length
Code
All dimensions are in millimeters.
Thread
Size
Type
Thread
Code
Screw
Length
Code
E
Nom.
H
+ .002
- .006
L
± .010
T
Nom.
.112-40
(#4-40)
PS10
440
40
.18
.075
.33
.13
.138-32
(#6-32)
PS10
632
40
.21
.075
.33
.13
.164-32
(#8-32)
PS10
832
40
.25
.075
.33
.13
.190-32
(#10-32)
PS10
032
40
.28
.075
.33
.13
PF-22 PennEngineering • www.pemnet.com
METRIC
UNIFIED
All dimensions are in inches.
Type and
Material
Thread
Size x
Pitch
Type
Thread
Code
Screw
Length
Code
E
Nom.
H
+ 0.05
- 0.15
L
± 0.25
T
Nom.
M3 x 0.5
PS10
M3
40
4.7
1.91
8.38
3.3
M4 x 0.7
PS10
M4
40
6.3
1.91
8.38
3.3
M5 x 0.8
PS10
M5
40
7.1
1.91
8.38
3.3
PEM® TYPE PF10 FLUSH-MOUNTED CAPTIVE PANEL SCREWS
PR10 SELF-CLINCHING FLUSH-MOUNTED RETAINERS
PR10
Retainer
E
PART NUMBER DESIGNATION
B
PR10–832
H
A
Type
C
Clinching profile may vary.
Thread Size
Code
Threads:
Internal, ASME B1.1, 2B / ASME B1.13M, 6H (1)
Material:
300 Series Stainless Steel
Finish:
Passivated and/or tested per ASTM A380
For use in sheet hardness:
HRB 70 or less (Hardness Rockwell “B” Scale)
HB 125 or less (Hardness Brinell)
All dimensions are in inches.
Type
Thread
Code
A
(Shank)
Max.
Min. Sheet
for SelfClinching
Min. Sheet
for Flush
Installation
Hole Size
in Sheet
+ .003
- .000
B
Nom.
C
Max.
E
Nom.
H
Nom.
Min. Dist.
HoleC/L
to Edge
.112-40
(#4-40)
PR10
440
.125
.050
.125
.281
.195
.280
.31
.075
.31
.138-32
(#6-32)
PR10
632
.125
.050
.125
.312
.225
.311
.34
.075
.33
.164-32
(#8-32)
PR10
832
.125
.050
.125
.344
.255
.343
.37
.075
.34
.190-32
(#10-32)
PR10
032
.125
.050
.125
.375
.290
.374
.41
.075
.36
Type
Thread
Code
A
(Shank)
Max.
Min. Sheet
for SelfClinching
Min. Sheet
for Flush
Installation
Hole Size
in Sheet
+ 0.08
B
Nom.
C
Max.
E
Nom.
H
Nom.
Min. Dist.
HoleC/L
to Edge
M3 x 0.5
PR10
M3
3.18
1.27
3.18
7.14
4.75
7.12
7.87
1.91
7.87
M4 x 0.7
PR10
M4
3.18
1.27
3.18
8.74
6.48
8.72
9.53
1.91
8.64
M5 x 0.8
PR10
M5
3.18
1.27
3.18
9.53
7.37
9.5
10.41
1.91
9.14
UNIFIED
Thread
Size
METRIC
All dimensions are in millimeters.
Thread
Size x
Pitch
N10 SELF-CLINCHING RECEPTACLE NUTS(4)
N10
Receptacle Nut
C
H
A
Threads:
Internal, ASME B1.1, 2B / ASME B1.13M, 6H (2)
Material:
Hardened Carbon Steel
Finish:
ZI - Zinc plated, 5µm, colorless (standard) (3)
For use in sheet hardness:
HRB 80 or less (Hardness Rockwell “B” Scale)
HB 150 or less (Hardness Brinell)
PART NUMBER DESIGNATION
N10–
832– 1
ZI
F
T
Type
UNIFIED
All dimensions are in inches.
Thread Size
Code
E
Clinching profile may vary.
Shank Finish
Code Code
Thread
Size
Type
Thread
Code
Shank
Code
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ .003
- .000
C
Max.
E
Nom.
F
± .010
H
Nom.
T
± .005
Min. Dist.
HoleC/L
To Edge
.112-40
(#4-40)
N10
440
1
.038
.040
.187
.186
.28
.130
.126
.24
.22
.138-32
(#6-32)
N10
632
1
.038
.040
.213
.212
.31
.130
.156
.24
.27
.164-32
(#8-32)
N10
832
1
.038
.040
.250
.249
.34
.130
.187
.24
.28
.190-32
(#10-32)
N10
032
1
.038
.040
.277
.276
.37
.130
.213
.24
.31
H
Nom.
T
± 0.13
Min. Dist.
HoleC/L
To Edge
METRIC
All dimensions are in millimeters.
Thread
Size x
Pitch
Type
Thread
Code
Shank
Code
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+ 0.08
C
Max.
E
Nom.
F
± 0.25
M3 x 0.5
N10
M3
1
0.97
1
4.75
4.73
7.11
3.3
3.2
6
5.59
M4 x 0.7
N10
M4
1
0.97
1
6.35
6.33
8.64
3.3
4.75
6
7.11
M5 x 0.8
N10
M5
1
0.97
1
7.04
7.01
9.53
3.3
5.41
6
7.87
(1) The purpose of the thread is for component screw retention only, thread may not accept 2B/6H Go threaded plug gage, but class 3A/4h
screw must pass with finger torque, may not reject NoGo threaded plug gage and minor diameter may exceed 2B/6H maximum.
(2) 2B (unified) and 6H (metric) go gauge may stop at pilot end but class 3A (unified) and 4h (metric) screws will pass through with finger torque.
(3)See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
(4)Also available on special order Type F10 self-clinching floating receptacle nuts.
PennEngineering • www.pemnet.com PF-23
REELFAST® SURFACE MOUNT CAPTIVE PANEL SCREWS
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
• All metal captive screw assembly installs in one piece
utilizing pick and place method.
• Combination drive, Torx®/slot.
• Solderable finish.
Material:
Retainer: Carbon Steel
Screw: Hardened Carbon Steel
Spring: 300 Series Stainless Steel
NEW
Finish:
Retainer:ET - Electro-plated tin ASTM B545, Class B with preservative coating, annealed (2)
Screw: ZI - Zinc plated, 5µm, colorless (3)
!
Dimples on head
designate metric thread.
Torx®/slot driver size.
(See chart)
E1
H
ØD
T2
Two Groove
(Registered
Trademark)
Solder
Pad
T1
Plated through
hole not required.
PART NUMBER DESIGNATION
SMTPF LS
Type
M– 440– 0
Driver Anti-cross Thread Length
Thread
Code
Code
Feature
ET
Finish
Code
UNIFIED
All dimensions are in inches.
ØH
G1
C
A
G2
E2
Installation Data page 36. Performance Data page 41.
ØK Hole Size ØD Min.
Screw A Min.
in Sheet
Solder Driver
Thread
Thread Length (Shank) Sheet
C
E1E2G1G2HT1T2
Type Code Code Max.ThicknessMax. ±.010 Nom ±.025±.025±.010Nom.Nom.+.003 -.000PadSize
Size
.112-40
SMTPFLSM440 0 .063 .063 .215.280.300.040.210 .100 .38 .55
.220 .340T15
(#4-40)
1
.100
.270
.138-32
SMTPFLSM632 0.063 .063 .247.310.320.040.240 .100 .42 .62
.252 .400T15
(#6-32)
1
.100
.300
METRIC
All dimensions are in millimeters.
ØK Hole Size ØD Min.
Screw A Min.
in Sheet
Solder Driver
Thread
Thread Length (Shank) Sheet
C
E1E2G1G2HT1T2
Type Code Code Max.ThicknessMax. ±0.25 Nom ±0.64±0.64±0.25Nom.Nom. +0.08 PadSize
Size
0
15.3
M3 x 0.5 SMTPFLSM
M3
1.61.65.467 7.6
2.59.614 5.6 8.6
T15
1
2.5
6.8
0
16.1
2.5 10.7 15.7
6.4 10.2T15
M3.5 x 0.6 SMTPFLSM M3.5
1.6 1.6 6.277.98.13
1
2.5
7.62
NUMBER OF PARTS PER REEL
ThreadScrew Length Code
Size
-0 -1
440
200 200
632
150 150
M3
200 200
M3.5
150 150
Packaged on 330 mm recyclable reels. Tape width is 24 mm. Supplied with polyimide patch for vacuum pick up. Reels conform to EIA-481.
(1) 2B (unified) and 6H (metric) go gauge may stop at pilot end but class 3A (unified) and 4h (metric) screws will pass through with finger torque.
(2) Optimal solderability life noted on packaging.
(3) See PEM Technical Support section of our web site (www.pemnet.com) for related plating standards and specifications.
PF-24 PennEngineering • www.pemnet.com
REELFAST® SMT PANEL SCREW COMPONENTS AND ASSEMBLY DATA
• Retainer installed using conventional surface mount
techniques.
• Simply snap screw into retainer to complete assembly.
• Black ABS knob standard.
• Optional molded-through colors available.
• Available with Torx® recess.
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g (1)
Material:
Knob: ABS (2)
Retainer: Carbon Steel
Screw: Carbon Steel
Finish:
Retainer:ET - Electro-plated tin ASTM B545, Class B with preservative coating, annealed
Screw: CN - Bright nickel over copper flash per ASTM B689
When Assembled
T2
Spring action of
plastic “fingers”
holds screw
in retracted
position.
P
PC Board
E C
G
Patented.
SMTPR
L
T1
PSHP
Installation Data page 36.
Performance Data page 41.
A
All dimensions are in inches.
UNIFIED
Screw Part Number
Assembly Dimensions
Screw
Retainer
Thread
Thread Length
Part
G
Size
Type Code
Code
Number
± .025
0
.188
.112-40
PSHP 440
SMTPR-6-1
(#4-40)
1
.248
.138-32
PSHP
(#6-32)
0
SMTPR-6-1
1
632
E1
B C1
T
R
Screw Dimensions
R
etainer Dimensions
TotalA
Min.
Radial C1E1
L
T (Shank)Sheet B
C
E R
Float ±.010 ±.010 ±.015 Nom.
Max. Thick. ±.003 Max. Nom. ±.005
P
± .025
T1
Nom.
T2
Nom.
.000
.026
.478
.646
.510.663
.015 .440.542
.060 .060.167.249.375.325
.570
.723
.478
.646
.510.663
.020 .440.542
.060 .060.167.249.375.325
.570
.723
.188
.000
.248
.026
All dimensions are in millimeters.
METRIC
Screw Part Number
Assembly Dimensions
Thread
Size x
Pitch
Screw
Retainer
Thread Length
Part
G
Type Code
Code
Number
± 0.64
0
4.78
M3 x 0.5 PSHP M3
SMTPR-6-1
1
6.3
M3.5 x 0.6 PSHP M3.5
0
SMTPR-6-1
1
Screw Dimensions
R
etainer Dimensions
TotalA
Min.
Radial C1E1
L
T (Shank)Sheet B
C
E R
Float ±0.25 ±0.25 ±0.38 Nom.
Max. Thick. ±0.08 Max. Nom. ±0.13
P
± 0.64
T1
Nom.
T2
Nom.
0
.66
12.14
16.41
12.9516.84
.38 11.1813.77
1.53 1.534.246.339.538.26
14.48
18.36
12.14
16.41
12.9516.84
.51 11.1813.77
1.53 1.534.246.339.538.26
14.48
18.36
4.78
0
6.3
.66
RETAINER - Packaged on 330 mm recyclable reels of
465 pieces. Tape width is 24 mm. Supplied with Kapton®
patch for vacuum pick up. Reels conform to EIA-481.
SCREW - Packaged in bags. Retainers and screws are
sold separately.
PART NUMBER DESIGNATION
FOR SCREW
PSHP–632– 0
Type
Thread
Code
L
Length Cap
Code Style
COLOR CAPABILITIES FOR TYPE PSHP SCREW
001
Color
Code
(Lobed) (Standard
Black)
The colors shown here (codes #002 thru #007) are non-stocked
standards and available on special order. Since actual cap colors
may vary slightly from those shown here, we recommend that you
request samples for color verification. If you require a custom color or
you need a “color matched” cap, please contact us.
Std. Black #001 Red #002 Orange #003 Yellow #004
Available with Torx®
recess on special order.
PART NUMBER DESIGNATION
FOR RETAINER
SMTPR– 6–1
Type
Retainer
Size
Shank
Code
ET
Finish
Code
.396”/
10.06 mm
Min.
Solder
Pad
Plated through
hole not required.
Green #005
Four dimples on
head designate
metric thread.
Blue #006
Violet #007
Non-flammable UL 94-V0 plastic caps are available on special order.
(1) 2B (unified) and 6H (metric) go gauge may stop at pilot end but class 3A
(unified) and 4h (metric) screws will pass through with finger torque.
(2) See PEM Technical Support section of our web site (www.pemnet.com) for
related plating standards and specifications.
.250” +.003 –.000
6.35 mm +0.08
Stencil Masking Examples
Metal Phillips Recess
#4-40 & M3 = #1
#6-32 & M3.5 = #2
PennEngineering • www.pemnet.com
PF-25
TYPE PFK BROACHING CAPTIVE PANEL SCREWS
• For permanent and reliable installation in PC boards and sheets of HRB 70 or less.
• Screw assemblies remain captive for easy mounting and removal.
Threads:
External, ASME B1.1, 2A / ASME B1.13M, 6g
Material:
Retainer: 300 Series Stainless Steel
Screw: 300 Series Stainless Steel
Spring: 300 Series Stainless Steel
Retaining Ring: Nylon, temperature limit 200˚ F / 93˚ C
Blue plastic retaining ring*
(Trademark)
Finish:
Retainer:Passivated and/or tested per ASTM A380
Screw:Passivated and/or tested per ASTM A380
Spring: Natural Finish
E
Diagonal knurl
identifies metric
thread sizes
H
T2
T1
P
PART NUMBER DESIGNATION
PFK–632–40
G
A
C
For use in:
PC Board and sheets HRB 70 or less (Hardness
Rockwell “B” Scale) HB 125 or less (Hardness Brinell)
Shoulder
provides
positive
stop during
installation.
Type
Installation Data page 33. Performance Data page 41.
Thread Size
Code
Screw
Length
Code
UNIFIED
All dimensions are in inches.
Thread
Size
Type
Thread
Code
.112-40
(#4-40)
PFK
440
.138-32
(#6-32)
PFK
632
Screw
Length
Code
40
62
84
40
62
84
A
(Shank)
Max.
Screw
Length
Code
40
62
84
Min.
Hole Size
Sheet
In Sheet
Thickness +.003 -.000
C
± .003
E
±.010
G
± .016
.250
.375
.500
.250
.375
.500
H
± .005
.072
P
± .025
.000
.125
.250
.000
.125
.250
T1
Max.
T2
Nom.
Min. Dist.
HoleC/L
To Edge
.36
.54
.20
.36
.54
.26
.060
.060
.265
.283
.312
.060
.060
.281
.299
.344
A
(Shank)
Max.
Min.
Sheet
Thickness
Hole Size
In Sheet
+0.08
C
± 0.08
E
±.25
G
± 0.4
H
± 0.13
P
± 0.64
T1
Max.
T2
Nom.
Min. Dist.
HoleC/L
To Edge
1.53
1.53
6.73
7.19
7.92
6.4
9.5
12.7
1.83
0
3.2
6.4
9.14
13.72
5.08
.072
METRIC
All dimensions are in millimeters.
Thread
Size x
Pitch
Type
Thread
Code
M3 x 0.5
PFK
M3
PF-26 PennEngineering • www.pemnet.com
VALUE-ADDED CAPABILITIES
VALUE-ADDED CAPABILITIES
Tight Seal Solutions
ATCA Solutions
Use Type PF11PM captive panel screw
and Type TPXS pin in conjunction to satisfy
the requirements of the PICMG 3.0 of the
Advanced TCA®.
Nylon Locking Patch
Nylon locking patch is available to be added
to any of PEM captive panel screws for
applications requiring a locking element.
Consider adding an o-ring to our PEM
C.A.P.S.® captive panel screw. When
fastened, it provides a tight seal above
the panel.
Thread-forming Opportunity
PennEngineering named official licensee for REMFORM®, TAPTITE
2000®, FASTITE 2000®, PT®, and DELTA PT® fastener products.
Both proprietary thread-forming fastener families are designed to
promote lower overall assembly costs. Contact us to learn more.
E-mail us at: techsupport@pemnet.com.
REMFORM®, TAPTITE® and FASTITE 2000® are trademarks of Reminc.
PT® and DELTA PT® are trademarks of EJOT®.
MAThread Anti Cross-thread Technology
PennEngineering is a licensee of MAThread® Anti Cross-Threading Technology. This unique design allows the
threads to self-align and drive easily with reduced effort. This helps speed assembly, reduce or eliminate failures,
repairs, scrap, downtime, and warranty service associated with thread damage. This option is available on most
types of PEM captive panel screws.
MAThread is a registered trademark of MAThread inc.
Anti Cross-Thread Feature
PennEngineering • www.pemnet.com
PF-27
CAPTIVE PANEL SCREW INSTALLATION (1)
TYPE PF11/PF12/PF11M/PF12M/PEM C.A.P.S.®
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary
operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch
side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until
the shoulder of the retainer comes in contact with the sheet material.
Thread Dia. +.080” / +2 mm
Max. Screw
Extension
PUNCH
PEMSERTER Installation Tooling
®
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.260
.437
8003521
8003518
632
.390
.468
8003522
8003519
832
.390
.531
8003523
8003520
032
.390
.531
8003523
8004350
0420
.480
.598
8004351
8004352
Thread
Code
METRIC
UNIFIED
Thread
Code
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
Punch Part
Number
M3
6.6
11.1
8003521
8003518
M3.5
9.91
11.89
8003522
8003519
M4
9.91
13.49
8003523
8003520
M5
9.91
13.49
8003523
8004350
M6
12.19
15.19
8004351
8004352
A
ANVIL
C
TYPE PF11MF/PF12MF (flare-mount installation)
1. Prepare properly sized mounting hole in sheet with countersink.
2. Place fastener into recessed anvil, and place workpiece over
shank of fastener.
3. With installation punch and anvil surfaces parallel, apply
squeezing force to flare the retainer of the fastener.
PEMSERTER® Installation Tooling
UNIFIED
Anvil Dimensions (in.) Punch Dimensions (in.)
Thread
A
C
E
F Anvil
Code
±.002
±.002
+.003 –.000
±.002
Part No.
METRIC
Punch
Part No.
.260
.437
.123
.133
8003521
8013670
632
.390
.468
.143
.156
8003522
8013671
832
.390
.531
.202
.210
8003523
8013672
032
.390
.531
.202
.210
8003523
8013672
0420
.480
.598
.255
.264
8004351
8013674
Anvil Dimensions (mm) Punch Dimensions (mm)
A
C
E
F Anvil
±0.05
±0.05
+0.08
±0.05
Part No.
Punch
Part No.
Thread
Code
M3
6.6
11.1
3.12
3.38
8003521
8013670
M4
9.91
13.49
5.13
5.33
8003523
8013672
M5
9.91
13.49
5.13
5.33
8003523
8013672
M6
12.19
15.19
6.48
6.71
8004351
8013674
(1) Punches and anvils should be hardened.
PF-28 PennEngineering • www.pemnet.com
AFTER INSTALLATION
PUNCH
.500” / 12.7mm
Min.
440
BEFORE INSTALLATION
ANVIL
A
PUNCH DETAIL
C
.015” ±.005” COUNTERSINK DETAIL
90˚
0.38mm ±0.1mm
Nom.
90˚
Nom.
E
F
Mounting Hole Dia.
(see page 6)
CAPTIVE PANEL SCREW INSTALLATION
E
TYPE PF11MW/PF12MW
Max. Screw
Extension
1. Prepare properly sized mounting hole in sheet.
2. Place fastener into recessed anvil, place
workpiece over shank of fastener, then place
the washer over the shank of the fastener.
3. With installation punch and anvil surfaces
parallel, apply squeezing force with flaring
punch.
PUNCH
PANEL
WASHER
FLARING PUNCH DETAIL
I
.010” R /
0.254mm R
Max.
.003” R /
0.08mm R
Max.
A
ANVIL
E
F
G
H
C
PEMSERTER Installation Tooling
®
Anvil Dimensions (in.)
UNIFIED
A
±.002
C
±.001
E
+.003 –.000
440
.260
.437
632
.390
.468
832
.390
032
0420
F
±.001
G
±.003
H
Min.
I
±.004
Anvil
Part No.
Punch
Part No.
.120
.135 .204
.250
.015
8003521
8014304
.140
.159 .249
.300
.015
8003522
8014305
.531
.201
.217 .340
.400
.028
8003523
8014306
.390
.531
.201
.217 .340
.400
.028
8003523
8014306
.480
.598
.252
.271 .430
.500
.028
8004351
8014307
Anvil Dimensions (mm)
METRIC
Punch Dimensions (in.)
Thread
Code
Punch Dimensions (mm)
Thread
Code
A
±0.05
C
±0.03
E
+0.08
F
±0.03
G
±0.08
H
Min.
I
±0.1
Anvil
Part No.
Punch
Part No.
M3
6.6
11.1
3.05
3.43 5.18
6.35
.381
8003521
8014304
M3.5
9.9
11.9
3.56
4.04 6.32
7.62
.381
8003522
8014305
M4
9.9
13.5
5.11
5.51 8.64
10.16
.711
8003523
8014306
M5
9.9
13.5
5.11
5.51 8.64
10.16
.711
8003523
8014306
M6
12.2
15.2
6.4
6.8810.92
12.7
.711
8004351
8014307
TYPE PFHV
Thread Dia. +.080” / +2 mm
1. Prepare properly sized mounting hole in sheet. Do not perform any
secondary operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the
punch side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force
until the shoulder of the retainer comes in contact with the sheet material.
Max. Screw
Extension
PUNCH
Thread
Code
Anvil Dimensions (in.)
Anvil Part
A
C
Number
±.002
±.002
Punch Part
Number
440
.220
.285
8004688 970200009400
632
.250
.301
8004689
832
.285
.332
8005439 970200230400
8015656
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
A
Punch Part
Number
M3
5.59
7.24
M3.5
6.35
7.65
8004689
M4
7.24
8.43
8005439 970200230400
ANVIL
8004688 970200020400
8015656
C
PennEngineering • www.pemnet.com
PF-29
CAPTIVE PANEL SCREW INSTALLATION
TYPE PF7M
1. Prepare properly sized mounting hole in sheet. Do not
perform any secondary operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece
(preferably the punch side) over the shank of fastener.
3. With installation punch and anvil surfaces parallel, apply
squeezing force until the shoulder of the retainer comes in
contact with the sheet material.
Thread Dia.
+.080” / +2mm
PUNCH
Max. Screw
Extension
.020” / .51 mm
x 45˚ Nom.
PEMSERTER Installation Tooling
®
UNIFIED
Thread
Code
AnvilPunch
PartPart
Number Number
440
.319
.290
80161758003518
632
.333
.330
8016176
8003519
832
.353
.385
8016177
8003520
Thread
Code
METRIC
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Dimensions (mm)
A
C
±0.05
±0.05
A
ANVIL
AnvilPunch
PartPart
Number Number
M3
8.1
7.34
80161758003518
M4
8.9
9.8
8016177
C
8003520
AFTER INSTALLATION
BEFORE INSTALLATION
TYPE PF7MF (flare-mount installation)
PUNCH
1. Prepare properly sized mounting hole in sheet with
countersink. Do not perform any secondary operations
such as deburring.
2. Place fastener into recessed anvil, and place workpiece
(preferably the punch side) over the shank of fastener.
3. With installation punch and anvil surfaces parallel, apply
squeezing force to flare the retainer of the fastener.
Max. Screw
Extension
.020” / .51mm
x 45˚ Nom.
ANVIL
PUNCH DETAIL
A
PEMSERTER® Installation Tooling
METRIC
UNIFIED
Thread
Code
Anvil Dimensions (in.) Punch Dimensions (in.)
A
C
E
F Anvil
±.002
±.002
+.003 –.000
±.002
Part No.
Punch
Part No.
C
440
.319
.290
.123
.133
8016175
8013670
632
.333
.330
.143
.156
8016176
8013671
COUNTERSINK DETAIL
832
.353
.385
.202
.210
8016177
8013672
90˚ Nom.
Anvil Dimensions (mm) Punch Dimensions (mm)
A
C
E
F Anvil
±0.05
±0.05
+0.08
±0.05
Part No.
Punch
Part No.
Thread
Code
M3
8.1
7.34
3.12
3.38
8016175
8013670
M4
8.9
9.8
5.13
5.33
8016177
8013672
PF-30 PennEngineering • www.pemnet.com
90˚
Nom.
E
F
Mounting Hole Dia.
(see page 11)
.015” ±.005”
0.38 mm ±0.1mm
CAPTIVE PANEL SCREW INSTALLATION
TYPE PF30/PF31/PF32
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary
operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch
side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until
the shoulder of the retainer comes in contact with the sheet material.
Thread Dia. +.080” / +2mm
Max. Screw
Extension
PUNCH
Thread
Code
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.295
.421
975201060 975200060
632
.295
.453
975201061 975200061
832
.310
.484
975201062 975200062
032
.310
.546
975201063 975200063
0420
.365
.640
975201064 975200064
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
Punch Part
Number
M3
7.49
10.69
975201060 975200060
M4
7.87
12.29
975201062 975200062
M5
7.87
13.87
975201063 975200063
M6
9.27
16.26
975201064 975200064
A
ANVIL
C
TYPE PF50/PF51/PF52/PF60/PF61/PF62
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary
operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch
side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until
the shoulder of the retainer comes in contact with the sheet material.
Thread
Code
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.295
.421
975201060 975200060
632
.295
.453
975201061 975200061
832
.310
.484
975201062 975200062
032
.310
.546
975201063 975200063
0420
.365
.640
975201064 975200064
Thread
Code
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
Thread Dia. +.080” / +2mm
Max. Screw
Extension
PUNCH
A
Punch Part
Number
M3
7.49
10.69
975201060 975200060
M3.5
7.49
11.51
975201061 975200061
M4
7.87
12.29
975201062 975200062
M5
7.87
13.87
975201063 975200063
M6
9.27
16.26
975201064 975200064
ANVIL
C
PennEngineering • www.pemnet.com
PF-31
CAPTIVE PANEL SCREW INSTALLATION
TYPE PFC4
Thread Dia. +.080” / +2mm
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary
operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch
side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until
the shoulder of the retainer comes in contact with the sheet material.
PUNCH
Max. Screw
Extension
Installation Requirements
1. Sheet hardness must be less than 88 on the Rockwell “B” scale.
2. Hole punch should be kept sharp to minimize work hardening around hole.
3. Fastener should be installed in punch side of hole.
4. Fastener should not be installed near bends or other highly cold worked
areas where sheet hardness may be greater than 88 on the Rockwell “B” scale.
ANVIL
A
C
Thread
Code
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.345
.358
975200027
975200060
632
.345
.390
975201243
975200061
832
.435
.421
975200029
975200062
032
.435
.452
975201244
975200063
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
Anvil Dimensions (mm)
A
C
±0.05
±0.05
Anvil Part
Number
Punch Part
Number
M3
8.76
9.09
975200027
975200060
M4
11.05
10.69
975200029
975200062
M5
11.05
11.48
975201244
975200063
TYPE PFC2P
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer
comes in contact with the sheet material.
Thread Dia. +.080” / +2mm
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.345
.323
975200026
975200060
632
.345
.358
975200027
975200061
832
.435
.386
975200028
975200062
032
.435
.421
975200029
9752000063
Thread
Code
Anvil Dimensions (mm)
A
C
±0.05
±0.05
PUNCH
Max. Screw
Extension
ANVIL
Anvil Part
Number
Punch Part
Number
M3
8.76
8.2
975200026
9752000060
M4
11.05
9.8
975200028
9752000062
M5
11.05
10.69
975200029
9752000063
A
C
PF-32 PennEngineering • www.pemnet.com
CAPTIVE PANEL SCREW INSTALLATION
TYPE PFC2/PFS2
Thread Dia. +.080” / +2mm
1. Prepare properly sized mounting hole in sheet. Do not perform any
secondary operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the
punch side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force
until the shoulder of the retainer comes in contact with the sheet material.
Max. Screw
Extension
PUNCH
Thread
Code
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.345
.323
975200026 975200060
632
.345
.358
975200027 975200061
832
.435
.386
975200028 975200062
032
.435
.421
975200029 975200063
0420
.565
.484
975200030 975200064
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
M3
8.76
M4
M5
M6
ANVIL
Punch Part
Number
8.2
975200026 975200060
11.05
9.8
975200028 975200062
11.05
10.69
975200029 975200063
14.35
12.29
975200030 975200064
A
C
TYPE PTL2/PSL2
Pin Dia. +.080” / +2mm
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary
operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch
side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until the
shoulder of the retainer comes in contact with the sheet material.
Max. Pin
Extension
Plunger Anvil Dimensions (in.)
Anvil Part
Diameter
A
C
Number
Code
±.002
±.002
04
.580
.520
Punch Part
Number
975201245 970200013300
ANVIL
A
METRIC
UNIFIED
PEMSERTER® Installation Tooling
PUNCH
Plunger Anvil Dimensions (mm)
Anvil Part
Diameter
A
C
Number
Code
±0.05
±0.05
04
14.86
13.21
Punch Part
Number
975201245 970200013300
C
TYPE PFK
Thread Dia. +.080” / +2mm
1. Prepare properly sized mounting hole in board.
2. Place fastener into recessed anvil, and place workpiece over shank of
fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force
until the shoulder of the retainer comes in contact with the board.
PUNCH
Max. Screw
Extension
Thread
Code
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.320
.323
975200026 975200060
632
.320
.358
975200027 975200061
ANVIL
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
M3
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
8.13
8.2
Punch Part
Number
A
975200026 975200060
C
PennEngineering • www.pemnet.com
PF-33
CAPTIVE PANEL SCREW INSTALLATION
TYPE SCBR
1. Prepare properly sized mounting hole in sheet. Do not perform
any secondary operations such as deburring. If the hole is
punched, be sure to install fastener into punched side of hole.
2. Assemble spring on screw by rotating spring counter clockwise
and position assembly into recessed magnetic punch.
3. Position hole in workpiece over retractable anvil pin.
4.With installation punch and anvil surfaces parallel, apply
squeezing force on top of the screw head and the underside of
the sheet material. The squeezing action forces the displacer of
the screw into the sheet, causing it to reduce the mounting hole
diameter and captivate the screw.
Magnetic
Punch (1)
K
J
BEFORE
Magnetic
Punch (1)
AFTER
Magnetic
Punch (1)
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
440
632
Installation Tooling Dimensions (in.)
Anvil
Part Number
C JK
.113 - .116 .354 – .357
.035
970200048300
.139 - .142 .387 – .390
.035
970200052300
832
.165 - .168
Thread
Code
M3
M4
.416 – .419
.035
970200054300
Installation Tooling Dimensions (mm)
Anvil
Part Number
C JK
3.03 - 3.11 9.25 – 9.32
0.89
970200049300
4.03 - 4.11 10.8 – 10.9
0.89
970200053300
Magnetic Punch
Part Number (1)
ANVIL PIN
SHEET
8016210
8016211
8016212
L*
Magnetic Punch
Part Number (1)
+.125” / 3.18mm
Min.
8016213
8016214
ANVIL
* For “L”,
see page 18.
(1) Pneumatic punch may also be used. Please contact our PEMSERTER tooling
division for punch part numbers.
C
TYPE SCB/SCBJ
1. Prepare properly sized mounting hole in sheet.
2. Place the fastener through mounting hole (preferably the punch
side) and into anvil. A flat or recessed punch can be used.
3.With installation punch and anvil surfaces parallel, apply
squeezing force to the top of the screw head and the underside
of the sheet material. The squeezing action forces the shoulder
of the screw into the sheet, displacing sheet material, causing it
to fill the void under the head and shoulder of the screw.
H
E
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Installation Tooling Dimensions (in.)
Thread CodeC E H
440
.113 - .116
.270 - .280
.073 - .074
632
.139 - .142
.308 - .318
.073 - .074
L*
+.125” / 3.18mm
Min.
Installation Tooling Dimensions (mm)
Thread CodeC E H
M3
3.03 - 3.11
6.86 - 7.11
1.85 - 1.88
M4
4.03 - 4.11
8.53 - 8.79
1.85 - 1.88
PF-34 PennEngineering • www.pemnet.com
* For “L”,
see page 19.
C
CAPTIVE PANEL SCREW INSTALLATION
C
TYPE HSCB fastener into heat sink
1. Prepare properly sized mounting hole in heat sink. Do not perform any
secondary operations such as deburring. If the hole is punched, be sure
to install the fastener into the punch side of the hole.
2. Place the head of the screw into the recess of the installation anvil
and position assembly into recessed magnetic punch.
3. Place the spring over the shoulder of the screw, maintaining concentricity.
4. Position the heat sink mounting hole over the screw.
5. Bring the heat sink down over the screw and onto the shoulder of the
screw.
6.With installation punch and anvil surfaces parallel, apply a squeezing
force to the heatsink and the head of the screw. The squeezing action
forces the displacer of the screw into the heatsink, causing it to reduce
the mounting hole diameter and captivate the screw and spring.
PUNCH
ANVIL
AFTER
PEMSERTER® Installation Tooling
UNIFIED
Thread Installation Tooling Dimensions (in.)
AnvilPunch
Code
Part Number Part Number
CJ
440
.113 - .116
.322 - .324
8018043
970200006300
632
.139 - .142
.362 - .364
8018044
970200007300
ME TR IC
BEFORE
Thread Installation Tooling Dimensions (mm)Anvil
Punch
Code
Part Number Part Number
CJ
M3
3.03 - 3.11
8.43 - 8.48
8018045
J
.250” ±.005/
6.35mm ±0.13
ANVIL
970200229300
TYPE HSR nut/standoff
1) Prepare properly sized mounting hole in board.
2) Place fastener into the anvil hole and place the mounting hole over the shank of the fastener as shown in drawing.
3) With installation punch and anvil surfaces parallel, apply squeezing force until shoulder contacts the board.
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
Anvil Dimensions (in.)
Anvil Part
Punch Part
P
A±.005Number Number
HSR-440
.228 - .231
.115
975200846300
975200048
HSR-632
.290 - .293
.115
975200849300
975200048
PUNCH
METRIC
P
Anvil Dimensions (mm)
Anvil Part
Punch Part
Thread
P
Code
A±0.13Number Number
HSR-M3
5.8 - 5.86
2.92
975200846300
975200048
ANVIL
A
Final assembly
Once the screw and spring are captivated, assemble the heat sink to the circuit board by tightening the screw into
the receptacle nut or standoff until the audible “click” is heard. The screw will continue to rotate, but will no longer be
engaged in the threads or continue to actively tighten.
PennEngineering • www.pemnet.com
PF-35
CAPTIVE PANEL SCREW INSTALLATION
TYPE PR10
PUNCH
1. Prepare properly sized mounting hole in sheet. Do not perform any
secondary operations such as deburring.
2. Place fastener into the mounting hole (preferably the punch side).
3. With installation punch and anvil surfaces parallel, apply squeezing
force until the retainer is flush in the sheet.
ANVIL
TYPE N10
1. Prepare properly sized mounting hole in sheet. Do not perform any secondary
operations such as deburring.
2. Place fastener into recessed anvil, and place workpiece (preferably the punch
side) over shank of fastener.
3. With installation punch and anvil surfaces parallel, apply squeezing force until
the shoulder of the nut comes in contact with the sheet material.
A
Anvil Dimensions (in.)
A
C
±.002
±.002
Anvil Part
Number
Punch Part
Number
440
.225
.298
8006124
975200048
632
.225
.329
8006735
975200048
832
.225
.361
8006736
975200048
032
.225
.392
8006174
975200048
METRIC
UNIFIED
PEMSERTER® Installation Tooling
Thread
Code
PUNCH
Thread
Code
Anvil Dimensions (mm)
Anvil Part
A
C
Number
±0.05
±0.05
M3
5.72
7.57
8006124
975200048
M4
5.72
9.17
8006736
975200048
M5
5.72
9.6
8006174
975200048
TYPE SMTPFLSM CAPTIVE PANEL SCREWS
Polyimide patch applied
here for vacuum pick up.
Solder fastener in place
using standard surface
mount techniques.
Solder paste applied
to pad on PCB.
Installs in retracted/unfastened position
SMT CAPTIVE PANEL SCREWS
Polyimide patch applied
here for vacuum pick up.
Screw snapped in place.
Solder paste applied
to pad on PCB.
Solder fastener in place
using standard surface
mount techniques.
PF-36 PennEngineering • www.pemnet.com
ANVIL
Punch Part
Number
C
CAPTIVE PANEL SCREW PERFORMANCE DATA(1)
TYPE PF11/PF12/PF11M/PF12M/PEM C.A.P.S.®
Test Sheet Material
PF11
PF12
Thread
Code
Installation Retainer Pushout
(lbs.)
(lbs.)
440
632
832
032
0420
1500
2000
3000
3000
3500
Test Sheet Material
Cold-Rolled Steel
80
95
100
100
105
Installation
(lbs.)
Retainer Pushout
(lbs.)
2500
3500
4500
4500
5000
145
150
160
160
195
Type
METRIC
UNIFIED
Type
Aluminum
PF11
PF12
Thread
Code
M3
M4
M5
M6
Aluminum
Cold-Rolled Steel
Installation Retainer Pushout
(kN)
(N)
6.7
13.3
13.3
15.6
355
445
445
465
Installation
(kN)
Retainer Pushout
(N)
11.1
20
20
22.2
645
710
710
865
TypeThread
Code
Installation Retainer Pullout
(lbs.)(lbs.)
440
25081
632
300 175
PF11MF
832
350
032
350 180
0420
400 200
180
METRIC
UNIFIED
TYPE PF11MF
TypeThread
Code
Installation Retainer Pullout
(kN)(N)
M3
1.1360
M4
PF11MF
M5
M6
1.5 800
1.5 800
2 890
TYPE PF11MW
Code
Test Sheet Material
1.52mm
Cold-rolled Steel
TypeThread
Swaging Force
Retainer Pullout
(lbs.)(lbs.)
440
350112
METRIC
UNIFIED
Test Sheet Material
.060”
Cold-rolled Steel
TypeThread
Code
Swaging Force
Retainer Pullout
(N)(N)
1557
499
1779
612
M4
3114
897
M5
3114
897
M6
4003
945
632
400138
PF11MW
832
700202
PF11MW
032
700202
0420
900212
M3
M3.5
TYPE PFHV
PFHV
Thread
Code
440
632
832
Aluminum
Installation Retainer Pushout
(lbs.)
(lbs.)
1700
1850
2100
Test Sheet Material
Cold-Rolled Steel
108
117
134
Installation
(lbs.)
Retainer Pushout
(lbs.)
2200
2400
2700
118
128
147
METRIC
UNIFIED
Test Sheet Material
Type
Type
PFHV
Thread
Code
M3
M3.5
M4
Aluminum
Cold-Rolled Steel
Installation Retainer Pushout
(kN)
(N)
8.1
8.8
9.4
516
561
599
Installation
(kN)
Retainer Pushout
(N)
10.5
11.4
12.1
564
614
656
(1) Published installation forces are for general reference. Actual set-up and confirmation of complete installation should be made by
observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when
all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation
procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to
provide technical assistance and/or samples for this purpose.
PennEngineering • www.pemnet.com
PF-37
CAPTIVE PANEL SCREW PERFORMANCE DATA(1)
METRIC
UNIFIED
TYPE PF7M
Type
PF7M
Rec.
Tightening
Thread
Torque
Code (in. lbs.) (2)
Test Sheet Material
Min.
Aluminum
Cold-rolled Steel
Screw
Tensile
Installation
Retainer Pushout
Installation
Retainer Pushout
(lbs.)
(lbs.) (lbs.)
(lbs.)
(lbs.)
440
4.5
580
1500
80
2500
145
PF7M
632
8.6
855
2000
95
3500
150
PF7M
832 15.6
1300
3000
100
4500
160
Type
PF7M
Rec.
Tightening
Thread
Torque
Code (N • m) (2)
Test Sheet Material
Min.
5052-H34 Aluminum
Cold-rolled Steel
Screw
Tensile
Installation
Retainer Pushout
Installation
Retainer Pushout
(N)
(kN)
(N)
(kN)
(N)
M3 0.66
2900
6.7
355
11.1
645
PF7M
M4 1.57
5010
13.3
445
20
710
Type
PF7MF
Rec.
Tightening
Thread Torque
Code (in. lbs.) (2)
Min. Screw
Tensile
(lbs.)
Installation
(lbs.)
Retainer
Pullout
(lbs.)
440
4.5
580
250
81
PF7MF
632
8.6
855
300
175
PF7MF
832
15.6
1300
350
180
METRIC
UNIFIED
TYPE PF7MF
Type
PF7MF
PF7MF
Rec.
Tightening
Thread Torque
Code
(N•m) (2)
Min. Screw
Tensile
(N)
Installation
(kN)
Retainer
Pullout
(N)
M3
0.66
2900
1.1
360
M4
1.57
5010
1.5
800
TYPE PF30/PF31/PF32
Test Sheet Material
PF30
PF31
PF32
PF30
PF31
PF32
PF30
PF31
PF32
PF30
PF31
PF32
PF32
Thread
Code
440
440
440
632
632
632
832
832
832
032
032
032
0420
Aluminum
Installation Retainer Pushout Installation
(lbs.)
(lbs.)
(lbs.)
2200
2200
2200
2400
2400
2400
2800
2800
2800
3500
3500
3500
4300
64
105
185
66
105
190
68
110
200
72
150
260
320
Test Sheet Material
Cold-Rolled Steel
5000
5000
5000
5500
5500
5500
6000
6000
6000
8000
8000
8000
12000
Type
Retainer Pushout
(lbs.)
90
110
300
90
130
300
90
130
300
95
160
425
450
METRIC
UNIFIED
Type
PF30
PF31
PF32
PF30
PF31
PF32
PF30
PF31
PF32
PF32
Thread
Code
M3
M3
M3
M4
M4
M4
M5
M5
M5
M6
Aluminum
Cold-Rolled Steel
Installation Retainer Pushout Installation
(kN)
(N)
(kN)
9.8
9.8
9.8
12.5
12.5
12.5
15.6
15.6
15.6
19.1
285
465
823
302
489
890
320
667
1156
1423
22.2
22.2
22.2
26.7
26.7
26.7
35.6
35.6
35.6
53.4
Retainer Pushout
(N)
400
489
1334
400
578
1334
423
712
1890
2002
(1) Published installation forces are for general reference. Actual set-up and confirmation of complete installation should be made by
observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when
all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation
procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to
provide technical assistance and/or samples for this purpose.
(2)Torque values shown will produce a preload of 70% minimum tensile with nut factor “k” equal to .1
PF-38 PennEngineering • www.pemnet.com
CAPTIVE PANEL SCREW PERFORMANCE DATA(1)
TYPE PF50/PF51/PF52/PF60/PF61/PF62
Test Sheet Material
TypeThread
Aluminum
Aluminum
Cold-Rolled Steel
Code
Installation Retainer Pushout Installation Retainer Pushout
(lbs.)(lbs.) (lbs.) (lbs.)
Code
Installation Retainer Pushout Installation Retainer Pushout
(kN)(N)(kN)(N)
PF50/PF60
PF51/PF61
PF52/PF62
PF50/PF60
PF51/PF61
PF52/PF62
PF50/PF60
PF51/PF61
PF52/PF62
PF50/PF60
PF51/PF61
PF52/PF62
PF52/PF62
PF50/PF60
M3
9.828522.2400
PF51/PF61
M3
9.846522.2489
PF52/PF62 M3
9.8
823
22.2
1334
PF50/PF60
M3.5
10.729424.4400
PF51/PF61
M3.5
10.746524.4578
PF52/PF62 M3.5
10.7
845
24.4
1334
PF50/PF60
M4
12.530226.7400
PF51/PF61
M4
12.548926.7578
PF52/PF62 M4
12.5
890
26.7
1334
PF50/PF60
M5
15.632035.6423
PF51/PF61
M5
15.666735.6712
PF52/PF62
M5
15.6115635.61890
PF52/PF62
M6
19.1142353.42002
440
440
440
632
632
632
832
832
832
032
032
032
0420
2200
2200
2200
2400
2400
2400
2800
2800
2800
3500
3500
3500
4300
64
105
185
66
105
190
68
110
200
72
150
260
320
5000
5000
5000
5500
5500
5500
6000
6000
6000
8000
8000
8000
12000
90
110
300
90
130
300
90
130
300
95
160
425
450
METRIC
UNIFIED
Test Sheet Material
TypeThread
Cold-Rolled Steel
UNIFIED
Test Sheet Material
304 Stainless Steel
TypeThread
Code
Installation
Retainer Pushout
(lbs.)(lbs.)
440
9100
350
METRIC
TYPE PFC4
Test Sheet Material
304 Stainless Steel
TypeThread
Code
Installation
Retainer Pushout
(kN) (N)
M3
40.5
1557
632
PFC4
832
10300 400
PFC4
M4
48
2002
10800
450
M5
11800
550
032
52.5
2447
TYPE PFC2/PFS2/PFC2P
Test Sheet Material
PFC2
PFS2
PFC2P
Thread
Code
440
632
832
032
0420
Installation Retainer Pushout
(lbs.)
(lbs.)
2400
2700
2900
3000
3500
Test Sheet Material
Cold-Rolled Steel
240
275
300
400
400
Installation Retainer Pushout
(lbs.)
(lbs.)
3000
3500
3800
4000
5000
300
350
400
500
600
Type
METRIC
UNIFIED
Type
Aluminum
PFC2
PFS2
PFC2P
Thread
Code
M3
M4
M5
M6
Aluminum
Cold-Rolled Steel
Installation Retainer Pushout
(kN)
(N)
10.7
12.9
13.3
15.6
1068
1334
1779
1779
Installation Retainer Pushout
(kN)
(N)
13.3
16.9
17.8
22.2
1334
1779
2224
2669
TYPE PTL2/PSL2
Test Sheet Material
Cold-Rolled Steel
Type
Installation Retainer Pushout Installation Retainer Pushout
(lbs.)(lbs.) (lbs.) (lbs.)
PTL2
3000400 4000 500
PSL2
METRIC
UNIFIED
Test Sheet Material
Aluminum
Aluminum
Cold-Rolled Steel
Type
Installation Retainer Pushout Installation Retainer Pushout
(kN)(N) (kN) (N)
PTL2
13.31779 17.8 2224
PSL2
(1) Published installation forces are for general reference. Actual set-up and confirmation of complete installation should be made by
observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when
all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation
procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide
technical assistance and/or samples for this purpose.
PennEngineering • www.pemnet.com
PF-39
CAPTIVE PANEL SCREW PERFORMANCE DATA(1)
METRIC
UNIFIED
TYPE SCBR
Type
SCBR
Rec.
Tightening
Thread
Torque
Code (in. lbs.) (2)
Min.
Aluminum
Screw
Tensile
Installation
(lbs.)
(lbs.) Test Sheet Material
Cold-rolled Steel
Pushout
(lbs.)
Installation
(lbs.)
Pushout
(lbs.)
440
5
590
1900
130
2600
145
SCBR
632
9
990
2000
175
3500
200
SCBR
832
17
1460
2250
225
3825
260
Type
SCBR
Rec.
Tightening
Thread
Torque
Code (N • m) (2)
SCBR
Test Sheet Material
Min.
5052-H34 Aluminum
Cold-rolled Steel
Screw
Tensile
Installation
Pushout
Installation
Pushout
(N)
(kN)
(N)
(kN)
(N)
M3 0.74
3400
8
580
12
650
M4
5700
10
1000
17
1150
1.7
Rec.
Tightening
Thread
Torque
Code (in. lbs.) (2)
METRIC
SCB / SCBJ
Type
SCB / SCBJ
UNIFIED
METRIC
HSCB
Type
HSCB
Cold-rolled Steel
Pushout
(lbs.)
Installation
(lbs.)
Pushout
(lbs.)
5
590
1900
130
2600
145
632
9
990
2000
175
3500
200
Test Sheet Material
Min.
5052-H34 Aluminum
Cold-rolled Steel
Screw
Tensile
Installation
Pushout
Installation
Pushout
(N)
(kN)
(N)
(kN)
(N)
M3
0.74
3400
8
580
12
650
M4
1.7
5700
10
1000
17
1150
TYPE HSCB
Type
HSCB
Test Sheet Material
440
Rec.
Tightening
Thread
Torque
Code (N • m) (2)
SCB / SCBJ
Min.
Aluminum
Screw
Tensile
Installation
(lbs.)
(lbs.) TYPE HSR
Test Sheet Material
Aluminum
Cold-rolled Steel
Thread
Pushout Installation
Pushout
CodeInstallation
(lbs.)
(lbs.)
(lbs.)
(lbs.)
440
1900
60 2600
80
632
90
120
2000
3500
Test Sheet Material
Aluminum
Cold-rolled Steel
Thread
PushoutInstallation
Pushout
CodeInstallation
(kN)
(N)(kN)
(N)
M38
26512
355
UNIFIED
Type
SCB / SCBJ
Test Sheet Material
.060” FR-4 Panel
TypeThread
Code Installation Pushout
(lbs.)
(lbs.)
HSR
METRIC
UNIFIED
TYPE SCB/SCBJ
440
HSR632
400
65
500
80
Test Sheet Material
1.5mm FR-4 Panel
TypeThread
Code Installation Pushout
(kN)
(N)
HSR
M3
2.2
290
(1) Published installation forces are for general reference. Actual set-up and confirmation of complete installation should be made by
observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when
all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation
procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to
provide technical assistance and/or samples for this purpose.
(2) Torque values shown will produce a preload of 70% minimum tensile (125 ksi / 935 MPa) with nut factor “k” equal to .1
PF-40 PennEngineering • www.pemnet.com
CAPTIVE PANEL SCREW PERFORMANCE DATA(1)
TYPE PR10
Test Sheet Material
Thread
Code
Cold-Rolled Steel
Installation
(lbs.)
Installation
(lbs.)
2100
2100
2100
2400
3000
3000
3600
4200
PR10
440
632
832
032
Type
METRIC
UNIFIED
Type
Test Sheet Material
Aluminum
PR10
Aluminum
Cold-Rolled Steel
Installation
(kN)
Installation
(kN)
M3
M4
M5
9.3
9.3
10.7
13.3
16
18.7
Thread
Code
Aluminum
Thread
Code
TYPE N10
Test Sheet Material
Thread
Code
N10
440
632
832
032
Test Sheet Material
Cold-Rolled Steel
Installation
(lbs.)
Pushout
(lbs.)
Installation
(lbs.)
Pushout
(lbs.)
2500
2500
3000
3500
95
105
110
120
3600
4000
5000
6300
130
145
180
200
Type
METRIC
UNIFIED
Type
Aluminum
N10
M3
M4
M5
Cold-Rolled Steel
Installation
(kN)
Pushout
(N)
Installation
(kN)
Pushout
(N)
11.1
13.3
15.6
423
489
534
16
22.2
28
578
800
890
Test Sheet Material
Min.Rec.
Type and
Tensile Tightening .060” P.C. Board
Thread Size
Strength
Torque
Pull-off
(5)
(lbs.) (in. lbs.) (4)(lbs.)
SMTPFLSM-440556 4.4
100
SMTPFLSM-632
724
7.0
METRIC
UNIFIED
REELFAST® TYPE SMTPFLSM RETAINER(2)
105
Test Sheet Material
Min.Rec.
Type and
Tensile Tightening 1.5 mm P.C. Board
Thread Size
Strength
Torque
Pull-off
(5)
(N)(N•m) (4)(N)
SMTPFLSM-M32900 0.61
445
SMTPFLSM-M3.5
3269
0.8
465
TESTING CONDITIONS FOR SMTPFLSM AND SMTPR
REELFAST TYPE SMTPR RETAINER
®
(2)
Test Sheet Material
Part
.062” Single Layer RF-4
Number
PushoutPushout
(lbs.)(N)
SMTPR-6-1ET161.4 718
Oven
Quad ZCR convection oven
High Temp
473˚F / 245˚C
Spokes
2 Spoke Pattern
Board Finish 62% Sn, 38% Pb
Screen Printer Ragin Manual Printer
ViasNone
Paste
Amtech NC559LF Sn96.5/3.0Ag/0.5Cu (SAC305) (Type SMTPR)
Alpha CVP-390 Sn96.5/3.0Ag/0.5Cu (SAC305) (Type SMTPFLSM)
Stencil
.0067” / 0.17 mm thick (Type SMTPR)
.005” / 0.13 mm thick (Type SMTPFLSM)
Test Sheet Material
Type Thread FR-4 Fiberglass
Code
Installation Pushout
(lbs.)(lbs.)
440
632
PFK
250 55
400 60
METRIC
UNIFIED
TYPE PFK
Test Sheet Material
Type Thread FR-4 Fiberglass
Code
Installation Pushout
(kN)(N)
PFKM3
1.1 245
(1) Published installation forces are for general reference. Actual set-up and confirmation of complete installation should be made by
observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when
all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation
procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide
technical assistance and/or samples for this purpose.
(2) With lead-free paste. Average values of 30 test points. The data presented here is for general comparison purposes only. Actual
performance is dependent upon application variables. We will be happy to provide samples for you to install. If required, we can also test
your installed hardware and provide you with the performance data specific to your application.
PennEngineering • www.pemnet.com
PF-41
CAPTIVE PANEL SCREW CAPABILITIES
MOST COMMONLY USED AND RECOMMENDED CAPTIVE MATING HARDWARE
FOR USE WITH CAPTIVE PANEL SCREWS
SELF-CLINCHING NUTS MATED WITH CAPTIVE PANEL SCREW
(See PEM® Bulletin CL)
• Types S/CLS/SS/CLSS provide load-bearing threads in thin sheets with high pushout and torque-out
resistance.
• Type SP nuts provide load-bearing threads in stainless steel sheets.
• Type CLA aluminum nuts are recommended for aluminum sheets with a hardness of HRB 50 / HB 89 or
less on the Rockwell “B” scale.
• Type SMPS nuts are for installation into ultra-thin sheets and can be mounted closer to the edge of a
sheet than other self-clinching nuts.
• Type SL nuts have a unique TRI-DENT® locking feature which meets demanding locking performance requirements.
TYPES AS/AC/A4 FLOATING NUTS MATED WITH CAPTIVE PANEL SCREW
(See PEM® Bulletin ALA)
• Types AS (carbon steel) and AC (300 series stainless steel) floating nuts install into sheets with hardness
up to HRB 70 / HB 125 on the Rockwell “B” scale.
• Type A4 (400 series stainless steel) floating nuts install into sheets with hardness up to HRB 88 / HB 183
on the Rockwell “B” scale.
• Thread locking versions also available.
TYPES B/BS BLIND NUTS MATED WITH CAPTIVE PANEL SCREW
(See PEM® Bulletin B)
• Type B/BS nuts are used in applications requiring closed thread ends.
• Provides barrier to protect threads against foreign matter.
• Protects internal components from intrusion of screws.
TYPE F FLUSH NUTS MATED WITH CAPTIVE PANEL SCREW
(See PEM® Bulletin F)
• Designed to be completely flush in sheets as thin as .060”/1.5mm.
• Ideal for applications where a thin sheet requires load-bearing threads but still must remain smooth, with
no protrusions on either surface.
• The hexagonal head ensures high axial and torsional strength.
• Type F nuts can be ordered to conform to US NASM45938/4 specifications.
TYPES KF2/KFS2 PC BOARD NUTS MATED WITH CAPTIVE PANEL SCREW
(See PEM® Bulletin K)
• Types KF2/KFS2 broaching nuts have a knurled-shank fastening device that can be pressed into a hole to
provide a permanent, strong, threaded attachment point in PC boards.
• Specially formed axial grooves around the shank of the nut “broach” or cut into the material, creating a
firm, interference-type fit resistance to rotation.
• Surface mounted nut hardware is also available.
For the best mating hardware for your application please contact our Tech Support line or your local representative.
PF-42 PennEngineering • www.pemnet.com
PEM® FASTENER IDENTIFICATION AND TRADEMARKS
To be sure that you are getting genuine PEM® brand fasteners, look for the unique PEM product markings and identifiers.
PEM C.A.P.S.
Dot Pattern
Skirted Shoulder
Identifier
“PEM” Stamp
(Trademark)
Type PF11PM
(Registered Trademark)
Types PF11, PF11M,
PF11MF, PF11MW, PF11PM,
PF12, PF12M, PF12MF,
PF12MW, PF7M, PF7MF
(Registered
Trademark)
Type PSHP
Double
Squares
(Registered
Trademark)
Type F10
Single
Groove
(Registered Trademark)
Type PFC4
Dimple
Two Groove
(Registered Trademark)
Types PF10, PF30, PF31, PF32, PF50, PF51, PF52, PF60,
PF61, PF62, PF11, PF11M, PF11MF, PF11MW, PF11PM, PF12,
PF12M, PF12MF, PF12MW, PF7M, PF7MF, PFC2, PFC2P,
PFC4, PFHV, PFK, PFS2, PSHP, SCB, SCBJ, SCBR
(Registered Trademark)
Types PF7M, PF7MF, N10,
HSR
Blue Retaining
Ring
(Trademark)
Types PFC4, PFC2P,
PFC2, PFS2, PFK
These panel fastener styles are protected by U.S. patents:
No. 6,814,530
No. D656,392S
No. D603,693S
Fastener drawings
and models are
available at
www.pemnet.com
PennEngineering • www.pemnet.com
PF-43
Regulatory compliance information is available in Technical
Support section of our website.
© 2015 PennEngineering.
PF-44
Specifications subject to change without notice.
See our website for the most current version of this bulletin.
Technical support e-mail: techsupport@pemnet.com