Bosch Conettix ITS-D6686-INTL Installation guide

Conettix ITS-D6686-INTL

EN

Installation Guide

Ethernet Network

Adapter

Conettix ITS-D6686-INTL | Installation Guide | Contents

Contents

1.0

Introduction ...................................................... 3

1.1

Network Interface................................................. 3

1.2

Serial Interface..................................................... 3

1.3

LEDs .................................................................... 3

2.0

Installation ........................................................ 4

2.1

Mounting the D6686 ............................................ 4

2.2

Connecting the D6686 ......................................... 4

3.0

Configuring and Programming the D6686 5

3.1

Factory Default IP Address .................................. 5

3.2

Identifying the MAC Hardware Address .............. 5

3.3

Obtaining an IP Address ...................................... 5

3.4

Using the D6200 to configure the D6686 ............ 5

3.5

Programming Overview for the D6600 ................ 8

4.0

Specifications ................................................... 9

2 Bosch Security Systems, Inc. | 11/12 | F01U274797-02

Conettix ITS-D6686-INTL | Installation Guide | 1.0 Introduction

.

Trademarks

All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

Copyright

This document is the intellectual property of

Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.

1.2 Serial Interface

Figure 2: D6686 Network Interface

1.0 Introduction

The Conettix D6686 Ethernet Network Adapter is a two-channel network adapter that supports IP

Addresses for both IPv4 and IPv6 environments.

Networked installations can have one if it is only used with one D6600 receiver or two configured channels when used with a backup D6600 receiver configuration.

Follow these instructions to avoid the possibility of harm to the operator, or damage to the equipment.

1.1 Network Interface

Figure 1: Power/Ethernet

1- Ethernet Link LED

2- RJ45 Ethernet Jack

3- Ethernet Activity LED

4- Reset Pin

5- Power Plug

1- Power/Diagnostic LEDs

2- Serial Port 2 (DTE) – optional (use supplied cable if required)

3- Serial Port 1 (DTE) – use supplied null cable

1.3 LEDs

Table 1: D6686 LEDs

LED

Power/Diagnostic

(Blue)

RX Serial 1 Activity

(Green)

TX Serial 1 Activity

(Yellow)

RX Serial 2 Activity

(Green)

TX Serial 2 Activity

(Yellow)

Ethernet Link

(Bi-color LED on left)

Ethernet Activity

(Bi-color LED on right)

Description

Steady On: Power OK

Blinking 2x: No DHCP response

Blinking 2x: Setup Menu active

Off: No data activity

Blinking: Data received by

D6686 on Channel 1

Off: No data activity

Blinking: Data transmitted from

D6686 on Channel 1

Off: No data activity

Blinking: Data received by

D6686 on Channel 2

Off: No data activity

Blinking: Data transmitted from

D6686 on Channel 2

Off: No Ethernet link established

Solid Yellow: 10 Mbps Ethernet link established

Solid Green: 100 Mbps Ethernet link established

Off: No data activity

Solid Yellow: Half Duplex data activity

Solid Green: Full Duplex data activity

Bosch Security Systems, Inc. | 11/12 | F01U274797-02 3

4

Conettix ITS-D6686-INTL | Installation Guide | 2.0 Installation

Figure 3: D6686 Connections

2.0 Installation

2.1 Mounting the D6686

Mount the D6686 on a rail or other user-supplied spot behind the D6600 that it will be connected to. Refer to Figure 3.

2.2 Connecting the D6686

Connect the D6686 as follows:

• Power cable to an available electrical outlet

• Ethernet cable to network switch

• RS-232 serial cable to Serial 1 port

Refer to the D6600/D6100IPv6 Installation and

Operation Guide – Network Communication

section, (P/N: 4998122704) for applications using both serial ports.

Refer to Figure 3.

1– Power cable

2– Ethernet cable

3– RS-232 serial cable (Serial 1 port)

4– Serial 2 port (empty)

5 – Standard 19-in. mounting rack

Bosch Security Systems, Inc. | 11/12 | F01U274797-02

Conettix ITS-D6686-INTL | Installation Guide | 3.0 Configuring and Programming the D6686

.

3.0 Configuring and

Programming the D6686

3.1 Factory Default IP Address

By default, the D6686 uses DHCP to obtain an IP

Address. The unit requires a static IP Address.

Refer to Sections 3.2, 3.3, and 3.4 for more information.

3.2 Identifying the MAC Hardware

Address

1. Verify that the D6686 is properly installed, connected, and powered.

Refer to Section 2.0 Installation on page 4.

2. Locate the D6686’s media access control

(MAC), or hardware, address.

The MAC address is hard-coded into the

D6686 during manufacturing, and it cannot be changed. This address is 6 bytes (12 digits) in length and is located on a label on the D6686 in the format of “xx-xx-xx-xx-xx-xx”.

Figure 4: MAC Address Location

1

1- MAC address location on D6686 label

3. Record the MAC address and keep it for reference.

3.3 Obtaining an IP Address

Provide the D6686’s MAC address to the site’s network administrator, who will assign an IP address for the D6686.

An IP Address is an identifier for a computer or device on a transmission control protocol/internet protocol (TCP/IP) network.

Networks use the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address using

IPv4 is a 32-bit numeric address written as four numbers or fields separated by periods. Each number can be 0 to 255. The format of an IP address using IPv6 is a 128-bit numeric address written as eight groups of four hexadecimal digits separated by colons.

For example, 190.200.128.111 could be an IPv4 address and

2001:0db8:85a3:0042:0000:8a2e:0370:7334 could be an IPv6 address. Within an isolated network, you can assign IP addresses at random if each one is unique. However, connecting a private network to the Internet requires using registered IP addresses (called Internet addresses) to avoid duplicates. IPv6 addresses are typically set using DHCP on the network. The

D6686 supports IPv4 and/or IPv6 addressing schemes or both at the same time.

3.4 Using the D6200 to configure the

D6686

Bosch Security Systems, Inc. recommends that you read this entire section before proceeding.

In order to access the configuration program, ensure that the D6686 and the PC used to configure it are directly connected using an

Ethernet cable.

Be sure that the PC being used to configure the device is configured to use DHCP to obtain an IP

Address. When it is connected directly to the D6686 it will obtain an Auto-IP address.

The D6200 Software is the recommended way to program the network devices. Review Section 3.5

Programming Overview for the D6600 on page 8 and the Network Utilities section in the D6200

Programming Software Operation and Installation

Guide (P/N: 4998154991).

1. When you have the IP address and the network administrator confirms that it is ready, connect the Ethernet port of the

D6686 directly to the PC Ethernet port using an Ethernet cable.

2. With the PC already booted and running, apply power to the D6686 and wait approximately 1 minute for the PC and

D6686 to acquire an Auto-IP Address

(169.254.xxx.xxx).

Bosch Security Systems, Inc. | 11/12 | F01U274797-02 5

6

Conettix ITS-D6686-INTL | Installation Guide | 3.0 Configuring and Programming the D6686

3. Open the D6200 software and select

Network – Network Utilities - Network

Device Setup as shown below

7. Click the Open XML button, select

D6686.xml, and click Open.

4. Select List All Conettix IP Devices tab and click the Start button. The program will scan the network for the device.

5. The D6686 will be shown in the list with the IP address. Record the IP address that is listed is shown.

6. Select XML Configuration tab and click the Setting button. Enter in the Setting dialog:

• D6686/D6100IPv6 IP: The IP address recorded in the previous step

• FTP User Name: admin

• FTP Password: PASS

• Click OK

8. Make changes to the parameters that are required for your particular installation scenario by selecting the specific item, enter the required changes, and click

Change. The values that are changed will be displayed in red as shown below. All of the programmable configuration parameters are listed on the next page with the valid values.

Bosch Security Systems, Inc. | 11/12 | F01U274797-02

.

Conettix ITS-D6686-INTL | Installation Guide | 3.0 Configuring and Programming the D6686

Bosch Security Systems, Inc. | 11/12 | F01U274797-02 7

8

Conettix ITS-D6686-INTL | Installation Guide | 3.0 Configuring and Programming the D6686

9. Click on the Save XML As button to save the changes made and enter a name for these configuration settings.

10. Click on the Send XML button to send these changes to the D6686. The device will save the changes and reboot with the new configuration.

11. Disconnect the Ethernet cable connecting the PC and the D66868 and connect the

D6686 to the network switch or router as required.

The D6686 is a Lantronix EDS-2100 with custom firmware installed and

UL Listed for use on the D6600. If standard Lantronix firmware is installed on a D6686, the device will no longer function on a D6600.

If encryption is enabled on the

D6686, you must enable it on all field devices (B420, DX4020-G,

B5512, etc) with the same key.

Encryption must also be enabled in the D6600 Receiver. Refer to the

D6600 Program Entry Guide (P/N:

4998122702).

The network interface module

(DX4020, C900V2, C900TTL-E, or

D9133TTL-E) must have the proper software version to support encryption. For more details, refer to the Device Installer Operation and

Installation Guide (P/N:

4998138688).

3.5 Programming Overview for the

D6600

The D6600 Receiver is shipped with factory default program parameters and features already installed. Descriptions of the program items are found in the D6600 Program Entry Guide (P/N:

4998122702). Many of the operational features of the D6600 can be altered through programming options. The programming options you choose depend on:

• The type(s) of peripheral reporting device(s) used in your central station (for example external printer or automation computer)

• The supervision characteristics for these devices

• The type of communicators reporting to the receiver

• The number and type of receiving lines in use

• Sending the files back to the D6600

(CPU/Host/Network, Account Database, or

Line Card)

• Upgrading the Software installed in the

D6600 (CPU, System, or PSTN line cards)

Refer to the D6200 Software Operation and

Installation Guide (P/N: 4998154991) for information and procedures on how to accomplish these tasks.

Bosch Security Systems, Inc. | 11/12 | F01U274797-02

Conettix ITS-D6686-INTL | Installation Guide | 4.0 Specifications

.

4.0 Specifications

Table 2: Specifications

Supported

Protocols

Connectors

ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, and FTP

Serial: 2 - DB9M DTE serial ports

Network: 1 - RJ45 10Base-T/100Base-TX Ethernet port

Cables

Ethernet: CAT5 or better unshielded twisted pair

Max Length: 6 m (20 ft) and installed in same enclosure/rack as

D6600.

RS-232: Max Length: 6 m (20 ft) and installed in same enclosure/rack as

D6600.

Serial speed ranging from 300 bps to 115.2 kbps (D6600 supports 38400 bps) Data Rates

Serial Line Formats

Characters

Stop bits:

7 or 8 data bits

1 or 2

Modem Controls

Flow Control

Management

System Software

Diagnostic LEDs

Compatibility

Parity:

DTR, DSR

Odd, even, none

Software: XON/XOFF

Hardware: CTS/RTS

FTP

SNMP (read only)

Serial login

Telnet login

Flash ROM standard: downloadable from a TCP/IP host (TFTP), FTP, or over serial port

Power

10/100 Mb Link on RJ45, 10/100 Activity on RJ45

RX Serial 1 Activity, TX Serial 1 Activity, RX Serial 2 Activity, TX Serial 2 Activity

Ethernet: v2.0/IEEE 802.3

D6600

UPS Standby Current: 0.4 A AC Current

Required

Power Input

Environmental

AC nominal operating range: 100 to 240 VAC, 50/60 Hz, 0.4A max

Operating Temperature: 0° to 50° C (32° to 122° F)

Storage Temperature: -40° to 85° C (-40° to 185° F)

Dimensions (H x W x D):

Unit: 3.75 in. x 2.9 in. x .9 in. (9.5 cm x 7.3 cm x 2.3 mm)

Weight 0.6 lbs. (0.26 kg)

Bosch Security Systems, Inc. | 11/12 | F01U274797-02 9

Bosch Security Systems, Inc.

130 Perinton Parkway

Fairport, NY 14450-9199

(800) 289-0096

© 2012 Bosch Security Systems, Inc.

F01U274797-02