15" RACK MOUNT INDUSTRIAL MONITOR REVISION F USER MANUAL

15" RACK MOUNT INDUSTRIAL MONITOR
REVISION F
USER MANUAL
Model No. HIS-RL15- _ _ _ F
Table of Contents
Safety and Regulatory Information��������������������������������������������������������������������������������3
FCC Notice����������������������������������������������������������������������������������������������������������������������������� 3
Waste Electrical and Electronic Equipment Directive (WEEE)����������������������������������������������� 4
Mechanical Drawings������������������������������������������������������������������������������������������������������5
Front View������������������������������������������������������������������������������������������������������������������������������� 5
Bottom View���������������������������������������������������������������������������������������������������������������������������� 5
Side View�������������������������������������������������������������������������������������������������������������������������������� 6
Installation Instructions��������������������������������������������������������������������������������������������������7
Step 1: Prepare for Installation���������������������������������������������������������������������������������������������� 7
Step 2: Bench-test Configuration������������������������������������������������������������������������������������������� 8
Install Cable Connections������������������������������������������������������������������������������������������������������������������ 8
Install Touchscreen���������������������������������������������������������������������������������������������������������������������������� 9
Step 3: Install into Rack������������������������������������������������������������������������������������������������������� 11
Video Settings����������������������������������������������������������������������������������������������������������������12
Setting the Timing Mode������������������������������������������������������������������������������������������������������� 12
Control Panel Buttons����������������������������������������������������������������������������������������������������������� 13
OSD and Power Lock Settings��������������������������������������������������������������������������������������������� 14
On-Screen Display (OSD) Menus����������������������������������������������������������������������������������������� 15
Auto Image Adjust Menu������������������������������������������������������������������������������������������������������������������ 16
Contrast / Brightness Menu������������������������������������������������������������������������������������������������������������� 16
Color Adjust Menu���������������������������������������������������������������������������������������������������������������������������� 17
Information Menu����������������������������������������������������������������������������������������������������������������������������� 18
Manual Image Adjust Menu������������������������������������������������������������������������������������������������������������� 18
Setup Menu�������������������������������������������������������������������������������������������������������������������������������������� 19
Memory Recall Menu����������������������������������������������������������������������������������������������������������������������� 19
Cleaning Instructions����������������������������������������������������������������������������������������������������20
Glass, Acrylic, and Touchscreen Window Models����������������������������������������������������������������� 20
No Protective Window (LCD Surface) Models���������������������������������������������������������������������� 20
Troubleshooting������������������������������������������������������������������������������������������������������������21
Video Troubleshooting���������������������������������������������������������������������������������������������������������� 21
Touchscreen Troubleshooting����������������������������������������������������������������������������������������������� 23
Specifications����������������������������������������������������������������������������������������������������������������24
Display���������������������������������������������������������������������������������������������������������������������������������� 24
Video������������������������������������������������������������������������������������������������������������������������������������� 24
Electrical������������������������������������������������������������������������������������������������������������������������������� 25
Environmental����������������������������������������������������������������������������������������������������������������������� 25
Functional����������������������������������������������������������������������������������������������������������������������������� 25
Rack Compatibility���������������������������������������������������������������������������������������������������������������� 25
Physical�������������������������������������������������������������������������������������������������������������������������������� 26
Compliances and Certifications�������������������������������������������������������������������������������������������� 26
Warranty Statement�������������������������������������������������������������������������������������������������������27
2 RL15F User Manual, June 2010
Safety and Regulatory Information
Safety and Regulatory Information
!
WARNING!
To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Do not disassemble the unit. Refer servicing to qualified personnel only.
This equipment is not intended for use in critical applications where its failure
to operate would create immediate life threatening circumstances. Applications
including, but not limited to, nuclear reactor control, aerospace navigation systems
and life support systems are not appropriate for this product.
This product is a UL Listed Product and must be used with a listed computer.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense. Any changes or modifications not
expressly approved by the grantee of this device could void the user’s authority to operate
the device.
RL15F User Manual, June 2010 3
Safety and Regulatory Information
Waste Electrical and Electronic Equipment Directive (WEEE)
The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose of the equipment as unsorted
municipal waste, but use the return and collection systems according to local law. Users
should contact their supplier and check the terms and conditions of the purchase contract.
When purchased directly from Hope Industrial Systems, you may contact technical support
for disposal arrangements.
4 RL15F User Manual, June 2010
Mechanical Drawings
Mechanical Drawings
Front View
482.6 mm
(19.00")
37.5 mm (1.48")
6.4 mm
(0.25")
230.4 mm
(9.07")
265.43 mm
(10.45")
190.5 mm
(7.50")
306.6 mm
(12.07")
37.5 mm (1.48")
Bottom View
377.8 mm
(14.87")
51.8 mm
(2.04")
3.2 mm
(0.125")
RL15F User Manual, June 2010 5
Mechanical Drawings
Side View
51.8 mm
(2.04")
265.43 mm
(10.45")
6 RL15F User Manual, June 2010
Installation Instructions
Installation Instructions
Step 1: Prepare for Installation
IMPORTANT!
Perform the following steps BEFORE installation of the monitor into the rack.
1. Ensure that sufficient power is available.
2. Ensure that sufficient space is available to allow for proper air flow into and out of the
unit.
3. Ensure that the air temperature around the unit (top and bottom) will not exceed the
rated specifications of the unit.
!
ff The maximum rated temperature for the HIS-RL15 is 50°C (122°F).
ff Remember that heat rises – the temperature at the top of the
cabinet will be much hotter than at the bottom if air inside the
enclosure is not actively circulating. Even in a sealed enclosure,
use of a circulation fan can greatly reduce temperature.
ff Also, remember that even though this product is designed to
operate at 50°C, the life span of any electronic device is shortened
when it is consistently operated at high temperatures. Therefore,
it is wise to take steps to keep the temperature of the ambient air
around the unit as low as possible.
4. Ensure that the ambient humidity of the air around the unit does not exceed the
specifications of the unit.
ff The maximum rated
non-condensing.
humidity
for
the
HIS-RL15
is
90% RL15F User Manual, June 2010 7
Installation Instructions
Step 2: Bench-test Configuration
Make sure everything works before installing into the production environment.

TIP!
If using a KVM extender, please refer to the installation instructions included with the
KVM extender module. It is particularly important to bench-test the full configuration
prior to final installation. This will help to identify and troubleshoot any system issues
while configuration changes may still be easily made.
Install Cable Connections
All monitors are shipped with both a 6 ft. VGA video cable and 6 ft. power cable, unless longer
cables were ordered in their place. If you ordered a touchscreen monitor, you also received a 6
ft. Serial (RS-232) cable and 6 ft. USB cable.
The cable ports are located on the rear of the monitor. Refer to the following diagram and
instructions to connect power, video, and touchscreen (if applicable) to your monitor.
POWER INPUT
8 RL15F User Manual, June 2010
SERIAL
(RS-232)
USB
VIDEO
(for Touchscreen option)
Installation Instructions
Video Connection
The HIS-RL15 supports analog video. Connect one end of the VGA video cable to the HD-15
input port on the rear of the monitor. Connect the other end to the video output port on the host
computer.
Power Connection
The HIS-RL15 is powered by 120/240 VAC, 0.5/0.25 A, 60/50 Hz.
Connect the AC power cable to the power input port on the rear of the monitor. Connect the other
end into a nearby outlet.
Install Touchscreen
Applies to touchscreen monitors only. Instructions below apply to Windows systems. Both Serial
and USB ports are present on all touchscreen monitors, but only one should be used to connect
the touchscreen interface to the monitor.
All touchscreen monitors are shipped with a CD-ROM that contains documentation and drivers for
all major operating systems. To be sure that you have the most current information, please check
the following Internet address:
http://www.HopeIndustrial.com/Touchscreen_Drivers.htm
IMPORTANT!
If you will be using a Serial connection, connect the Serial cable first, and then
install the touchscreen driver. If you will be using a USB connection, install the
touchscreen driver first, and then connect the USB cable.
Serial (RS-232) Connection
1. Connect one end of the Serial cable to the Serial input port on the rear of the monitor.
Connect the other end to the Serial port on the host computer. Tighten the captive
screws on the cable connectors to ensure adequate strain relief.
RL15F User Manual, June 2010 9
Installation Instructions
2. Select the appropriate driver for your operating system.
a. If downloading from the web address listed above, select the appropriate
driver for your operating system.
b. If using the included CD-ROM, insert it into the host computer's CD-ROM
drive. If the CD does not automatically run, browse the contents of the CD
and open the readme.htm file. Select the appropriate driver.
3. Click to "Run" the software when prompted. Follow on-screen instructions to
download and execute the touchscreen driver installation.
USB Connection
1. Select the appropriate driver for your operating system.
a. If downloading from the web address listed above, select the appropriate
driver for your operating system.
b. If using the included CD-ROM, insert it into the host computer's CD-ROM
drive. If the CD does not automatically run, browse the contents of the CD
and open the readme.htm file. Select the appropriate driver.
2. Click to "Run" the software when prompted. Follow on-screen instructions to
download and execute the touchscreen driver installation.
3. A cable retention bracket comes installed on the USB port on the rear of the monitor
and will help to secure the cable and ensure adequate strain relief. Route one end of
the USB cable through the retention bracket and connect it to the USB Type B input
port on the rear of the monitor. Connect the other end to the USB port on the host
computer.
Calibrate the Touchscreen
Once the driver has finished installing, you are ready to calibrate the touchscreen. Open the
touchscreen's Control Panel, located in the host computer's Control Panel.
NOTE: Some touchscreen drivers have an "Enhanced Calibration Mode" option. If applicable
to your particular driver, this setting may be found in the touchscreen's Control Panel under the
"Mode" tab.
10 RL15F User Manual, June 2010
Installation Instructions
Step 3: Install into Rack
Once you have completed the full bench-test configuration and confirmed that all components are
working properly, you are ready to install the monitor into the rack.
Hope Industrial Systems' Rack Mount monitors conform to the Electronic Industries Association
standard EIA-310-D. Our monitors will fit in type A, B, and C racks with a width of 482.6 mm (19")
(preferred EIA rack width).
!
WARNING!
HIS will not assume liability for damage to internal electronics due to improper
installation. Contact HIS if you need additional assistance.
The HIS-RL15 has a panel height of 6U (shown below).
0"
37.7 mm
(1.48")
6U
(10.45")
228.2 mm
(8.98")
265.4 mm
(10.45")
RL15F User Manual, June 2010 11
Video Settings
Video Settings
Setting the Timing Mode
Setting the timing mode of your computer graphics adapter (or other video source) is important
for maximizing the quality of the screen image and for minimizing eye strain. The timing mode
consists of the resolution (e.g. 1024 x 768) and refresh rate (or vertical frequency; e.g. 60 Hz).
After setting the timing mode, use the On-Screen Display (OSD) controls to adjust the screen
image.

TIP!
For the best picture quality, set your computer graphics adapter timing mode to:
VESA 1024 x 768 @ 60 Hz
Please refer to the computer graphics adapter manufacturer's manual for instructions on setting
the resolution and timing mode. In Microsoft Windows, these settings may be found at the
following location:
ff ME, 2000, XP: Control Panel > Display > Settings
ff Vista: Control Panel > Personalization > Display Settings
ff Windows 7: Control Panel > Appearance and Personalization >
Adjust Screen Resolution
!
WARNING!
Do not set the graphics card in your computer to exceed the maximum refresh rate
of 85 Hz; doing so may result in permanent damage to your display.
12 RL15F User Manual, June 2010
Video Settings
Control Panel Buttons
Use the control panel buttons located on the back of the monitor to display and adjust various
settings on the On-Screen Display (OSD) menu.
CONTROL PANEL BUTTONS
1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustments screens disappear automatically after
15 seconds. This is adjustable through the OSD timeout setting in the Setup
menu.
2. To select a control to adjust, press the up [▲] or down [▼] button to scroll through the
menu.
3. Press button [2] to open the menu for a selected control.
4. To adjust the control, press the up [▲] or down [▼] button.
5. To save the adjustments and return to the main OSD menu, press button [1] once. To
exit the OSD menu, press button [1] twice.
RL15F User Manual, June 2010 13
Video Settings
Button
Control
Functions
Up / Contrast Adjust
When the OSD menu IS NOT displayed:
• Shortcut to Contrast Adjust.
When the OSD menu IS displayed:
• Scrolls up and adjusts items in the menu up.
Down / Contrast
Adjust
When the OSD menu IS NOT displayed:
• Shortcut to Contrast Adjust.
When the OSD menu IS displayed:
• Scrolls down and adjusts items in the menu
down.
Power
• Turns the monitor on and off.
• The Power Indicator light glows green during
normal operation and orange when the monitor is
in Power Saving mode.
Enter
• Displays the control screen for the highlighted
control.
• Toggles between two controls on some screens.
Menu
• Opens the OSD menu.
• Exits the OSD menu and saves adjustments.
OSD and Power Lock Settings
ff OSD Lock: Press and hold [1] and the up [▲] button for 10 seconds. If any buttons
are pressed the message OSD Locked will display for 5 seconds.
ff OSD Unlock: Press and hold [1] and the up [▲] button again for 10 seconds.
ff Power Button Lock: Press and hold [1] and the down [▼] button for 10 seconds.
If the power button is pressed, the message Power Button Locked will display for 5
seconds. With or without this setting, after a power failure, your monitor's power will
automatically turn ON when power is restored.
ff Power Button Unlock: Press and hold [1] and the down [▼] button again for 10
seconds.
14 RL15F User Manual, June 2010
Video Settings
On-Screen Display (OSD) Menus
To open the OSD menu, press button [1] once. The following screen will appear:
Main Menu
Description
Auto Image Adjust
Automatically sizes, centers, and fine tunes the video signal to
eliminate waviness and distortion.
Contrast / Brightness
Includes the Contrast and Brightness functions.
Color Adjust
Provides several color adjustment modes.
Information
Displays the timing mode (video signal input).
Manual Image Adjust
Includes the H./V. Position, H. Size, Fine Tune, and Sharpness
functions.
Setup Menu
Includes the Language Select, Resolution Notice, OSD Position,
OSD Timeout, and OSD Background functions.
Memory Recall
Returns adjustments back to factory settings.
RL15F User Manual, June 2010 15
Video Settings
Auto Image Adjust Menu
The Auto Image Adjust menu automatically sizes, centers, and fine tunes the video signal to
eliminate waviness and distortion.
NOTE: Auto Image Adjust works with most common video cards. If this function does not work
on your display, lower the video refresh rate to 60 Hz and set the resolution to its pre-set value.
Contrast / Brightness Menu
The Contrast/Brightness menu includes the Contrast and Brightness functions.
Contrast / Brightness
Menu
Contrast
Description
• Adjusts the difference between the image background
(black level) and the foreground (white level).
• This feature may also be accessed by pressing the up [▲]
or down [▼] button outside of the OSD menu.
Brightness
16 Adjusts the background black level of the screen image.
RL15F User Manual, June 2010
Video Settings
Color Adjust Menu
The Color Adjust menu provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of red (R), green (G),
and blue (B). The factory setting for this product is 6500K (6500 Kelvin).
Color Adjust Menu
Description
sRGB
This is quickly becoming the industry standard for color
management, with support being included in many of the latest
applications. Enabling this setting allows the LCD to more
accurately display colors the way they were originally intended.
NOTE: Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
9300K
Adds blue to the screen image for cooler white (used in most
office settings with fluorescent lighting).
6500K
Adds red to the screen image for warmer white and richer red.
5400K
Adds green to the screen image for a darker color.
User Color
Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G, or B) press button [2].
2. To adjust selected color, press the up [▲] or down [▼]
button.
NOTE: If you select RECALL from the OSD Main Menu when
the product is set to a Preset Timing Mode, colors return to the
6500K factory preset.
RL15F User Manual, June 2010 17
Video Settings
Information Menu
The Information menu displays the timing mode (video signal input) coming from the graphics
card in the computer. See your graphics card's user guide for instructions on changing the
resolution and refresh rate (vertical frequency).
NOTE: VESA 1024 x 768 @ 60 Hz (recommended) means that the resolution is 1024 x 768 and
the refresh rate is 60 Hz.
Manual Image Adjust Menu
The Manual Image Adjust menu includes the H./V. Position, H. Size, Fine Tune, and Sharpness
functions.
Manual Image Adjust
Menu
Description
H./V. Position
(Horizontal / Vertical
Position)
Moves the screen image left or right and up or down.
H. Size (Horizontal Size)
Adjusts the width of the screen image.
Fine Tune
Sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try the Auto Image Adjust function first.
Sharpness
18 Adjusts the clarity and focus of the screen image.
RL15F User Manual, June 2010
Video Settings
Setup Menu
The Setup menu includes the Language Select, Resolution Notice, OSD Position, OSD Timeout,
and OSD Background functions.
Setup Menu
Description
Language Select
Allows the user to choose the language used in the menus and
control screens.
Resolution Notice
Advises the optimal resolution to use and displays the
Resolution Notice menu shown below:
OSD Position
Allows the user to move the OSD menus and control screens.
OSD Timeout
Sets the length of time the OSD screen is displayed. For
example, with a "15 second" time setting, if a control is not
pushed within 15 seconds, the display screen disappears.
OSD Background
Allows the user to turn the OSD background On or Off.
Memory Recall Menu
The Memory Recall menu returns adjustments back to factory settings.
NOTE: This control does not affect changes made with the User Color control, Language Select,
or Power Lock setting.
RL15F User Manual, June 2010 19
Cleaning Instructions
Cleaning Instructions
!
CAUTION!
DO NOT USE ABRASIVE MATERIALS, SUCH AS PAPER TOWELS OR DIRTY SHOP
RAGS, ON THE DISPLAY AS IT WILL SCRATCH THE PROTECTIVE COATING. ALWAYS USE A SOFT CLOTH, PREFERABLY MADE OF COTTON.
IMPORTANT!
Always spray the cleaner on the cloth or towel first and then clean the monitor
screen. Cleaner sprayed directly on the monitor could possibly leak inside a nonsealed unit and cause damage.
Glass, Acrylic, and Touchscreen Window Models
All displays with safety glass, acrylic, or resistive touchscreen windows may be cleaned using any
standard glass cleaner as long as there is no abrasive or oily content. Vinegar or ammonia will
not hurt the screen.
The anti-reflective coatings on glass window-equipped displays are physically part of the surface
of the glass and resist degradation to the Military Specifications.
To minimize over-run of cleaning solution, spray the cloth first and then clean the screen.
No Protective Window (LCD Surface) Models
Wipe the screen with a clean, soft, lint-free cloth. This will remove dust and other particles. If the
screen is still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner
onto a clean, soft, lint-free cloth, then wipe the screen.
20 RL15F User Manual, June 2010
Troubleshooting
Troubleshooting
Video Troubleshooting
IMPORTANT!
If using a KVM extender, first try to resolve any problems using the solutions listed
below. If the problem still exists, try bypassing the KVM extender. If this fixes the
problem and allows the monitor to work properly, then the KVM extender is the
source of the problem. Please refer to the troubleshooting section of the KVM
extender manual or contact HIS for additional assistance.
Symptom
Causes
Solutions
No image on
the screen and
control's Power
Indicator light is
not lit
Monitor is not powered on.
• Press the Power button on the
monitor and make sure the Power
Indicator light is lit green.
"No Signal"
message box
and no image on
the screen
Video cable is not plugged in
correctly.
Check the video cable connection at the
monitor, PC, and/or KVM extender.
PC is in Power Saving
mode.
Power Saving mode can usually be exited
by moving the mouse.
PC is not powered on.
Ensure PC is powered on.
PC is not sending signal.
Connect the PC to another known working
monitor to check the PC source signal.
Video cable is not plugged in
correctly.
Check the video cable connection at the
monitor, PC, and/or KVM extender.
PC is in Power Saving
mode.
Power Saving mode can usually be exited
by moving the mouse.
PC is not powered on.
Ensure PC is powered on.
PC is not sending signal.
Connect the PC to another known working
monitor to check the PC source signal.
No image on
the screen and
control's Power
Indicator light is
lit orange
• Check power connections at the
monitor and power source.
RL15F User Manual, June 2010 21
Troubleshooting
Symptom
Causes
Solutions
"Out of Range"
message box
and no image on
the screen
The source signal exceeds
the maximum resolution
and/or refresh rate that the
monitor can handle
( > 1024 x 768 resolution or
> 75 Hz refresh rate).
Adjust the computer settings to the
monitor's native resolution:
Incorrectly
displayed or
partial image on
the screen
Monitor has not been
adjusted correctly for the
source signal.
• Activate the "Auto Image Adjust"
function in the OSD menu.
Wrong or
abnormal colors
(white is not
white)
Monitor color settings are
incorrectly adjusted.
• Adjust the colors of the display using
the "Color Adjust" function in the OSD.
1024 x 768 @ 60 Hz
• Fine tune the picture by manually
adjusting the image. In the OSD
menu, these functions can be found in
the "Manual Image Adjust" menu.
• Reset the monitor to the factory
default settings by activating the
"Memory Recall" function in the OSD.
Video cable is not securely
connected.
If any colors (red, green, or blue) are
missing, check the video cable to make
sure it is securely connected.
Video cable is bad.
Check to make sure there are no loose
or broken pins in the cable connector.
Shorts in the cable could also cause an
improper image to display.
Screen image is
dim
Brightness and/or contrast
settings are not set properly.
Adjust the monitor's brightness and
contrast settings in the OSD's "Contrast/
Brightness" menu.
The message
"OSD Locked"
appears
The OSD has been locked
to prevent unauthorized
changes to display settings.
Press and hold [1] and the up [▲] button
for 10 seconds.
The message
"Power Button
Locked"
appears
The Power button has
been locked to prevent
unauthorized shut down of
the monitor.
Press and hold [1] and the down [▼]
button for 10 seconds.
22 RL15F User Manual, June 2010
Troubleshooting
Touchscreen Troubleshooting
Applies to touchscreen monitors only. To be sure that you have the most current driver, please
check the following Internet address:
http://www.HopeIndustrial.com/Touchscreen_Drivers.htm
Symptom
Causes
Solutions
No response
when touching
the touchscreen
Touchscreen driver has not
been installed.
Download and install the latest driver from
the HIS website.
Touchscreen cable is not
plugged in correctly.
Make sure either the USB or Serial cable
is securely connected to the monitor and
PC. Do not connect both.
If using a USB connection,
does the USB cable length
exceed 3 meters?
USB cables have a 3 meter limitation and
could cause no touch response if this is
exceeded.
If using a Serial connection,
is the Serial cable plugged
into the correct COM port?
Ensure that the Serial cable is connected
to the COM port being used prior to
installing the touchscreen driver.
Touchscreen driver has not
been installed.
Download and install the latest driver from
the HIS website.
Touchscreen has not been
calibrated.
Activate the calibration utility. In Windows
systems, these settings may be found at
the following location:
The cursor
moves but does
not follow my
finger when
touching the
touchscreen
Control Panel > Elo Touchscreen >
"General" Tab
• Press the Align button.
• Touch all targets as the appear to
calibrate the touchscreen.
• Press the Green Check button when
verified.
RL15F User Manual, June 2010 23
Specifications
Specifications
Display
Type
Thin-film transistor (TFT) Active Matrix Liquid Crystal
Size
15" diagonal
Image Size (W x H)
304 mm x 228 mm (12.0" x 9.0")
Native Resolution
XGA (1024 x 768, 4:3 aspect ratio)
Minimum Resolution
VGA (640 x 480)
Pixel Pitch
0.297 mm x 0.297 mm
Number of Colors
16.8 million
Brightness (white)
250 nits (cd/m2)
Viewing Angle (Hori/Vert)
160° / 115°
Contrast Ratio (typical)
500:1
Backlight
Two CCFTs (Cold Cathode Fluorescent Tube); 50,000 hours to
half brightness; replaceable
Video
Input Connectors
HD-15
NOTE: Optional BNC input using HD-15 to 5-wire BNC adapter;
see "Input Signal Formats" for a list of compatible video signals.
Input Signal Formats
RGB Analog video, 0.7/1.0 Vp-p, 75 Ohms
Compatible sync modes: Separate H/V sync
NOTE: NTSC/PAL composite input available (call for details)
Horizontal Scan
30 – 82 kHz
Vertical Scan
50 – 85 Hz
Supported Video
Standards
• 1024 x 768 @ 60, 70, 72, 75 Hz
• 800 x 600 @ 56, 60, 72, 75 Hz
• 640 x 480 @ 60, 75 Hz
• 720 x 400 @ 70 Hz
Response Rate (typical)
24 12 ms
RL15F User Manual, June 2010
Specifications
Electrical
Monitor Input
120/240 VAC, 0.5/0.25 A, 60/50 Hz
Power Consumption
~ 23 W
Power Management
DPMS/energy star, < 1 W
Environmental
Temperature
0° to 50°C (32° to 122°F)
Humidity
20% to 90% non-condensing
Operating Shock
15 g, 6 msec, half-sine
Operating Vibration (sine) 1.0g, swept sine 9 – 500 Hz
Transport Vibration
(random)
0.1g2 / Hz, 10 – 200 Hz
Altitude
• Operating: up to 10,000 feet
0.03g2 / Hz, 200 – 2000 Hz
• Non-operating: up to 40,000 feet
Functional
Control Panel Buttons
Up, Down, Power, 2 (Enter), 1 (Menu)
On-Screen Display (OSD)
Menus
Auto Image Adjust, Contrast / Brightness, Color Adjust,
Information, Manual Image Adjust, Setup, Memory Recall
Touchscreen Option
5-wire resistive system; emulates a mouse; Serial (RS-232) and
USB interface to host computer
Rack Compatibility
EIA Standard
EIA-310-D
EIA Type Rack
A, B, and C
Rack Width
482.6 mm (19.0") (preferred EIA width)
Mounting
4 Slots, 6.4 mm (0.25") wide
Panel Height
6U, 265.43 mm (10.45")
RL15F User Manual, June 2010 25
Specifications
Physical
Enclosure Type
Rack mount
Enclosure Rating
Built to IP20 standards; NEMA/UL Type 1
Bezel Finish
Black Powder-Coated Carbon Steel, matte finish
Depth Behind Bezel
51.8 mm (2.04")
Front Bezel Outside
Dimensions (W x H x D)
482.6 mm x 265.43 mm x 3.2 mm (19.0" x 10.45" x 0.125")
Net Weight
11 lbs.
Shipping Weight
15 lbs.
Compliances and Certifications
Electrical
• UL 60950-1 / cUL Recognized Component (File No.
E212889)
• UL 508A Listed (File No. E318630)
• FCC Class A
• CE
Environmental
• RoHS (Hazardous Substances)
• IEC 60721-3 (Reliability)
• WEEE (Registration No. WEE/DJ1859ZX for UK only)
Enclosure
26 UL50E (File No. E318630)
RL15F User Manual, June 2010
Warranty Statement
Warranty Statement
Who is Covered?
This warranty covers the purchaser of this product only and is not transferable without our written
consent.
What Does This Warranty Cover and What is the Period of Coverage?
We warrant this product to be free from defects in material and workmanship, subject to the conditions
set forth below. The warranty on all industrial display products, KB-R2-EXT and KB-M2-EXT series
keyboards, and ENCL-TC1 series enclosures remains in force for a three year period beginning on the
date we invoice you. The warranty period on KB-PL1 keyboards is two years, and all other keyboards
carry a one year warranty. If HIS repairs or replaces a product under warranty, its warranty term is not
extended.
What Will We Do to Correct Problems and How Do You Get Service?
We will repair or replace (at our sole option) any part of the unit which proves to be defective.
Replacement parts may be new or refurbished and will meet the same specifications of the original
parts or unit. We will return the product to you by the shipping method we choose in the U.S.A. at our
expense. You must pay for shipments to locations outside of the U.S.A. In order to receive warranty
service you must get prior approval from HIS. To request warranty service, you can telephone us at
877-762-9790 (1-678-762-9790 outside the U.S.) or send an e-mail to support@HopeIndustrial.com. If
we determine that warranty service is needed we will give you a Return Material Authorization (RMA)
number. This RMA number must be conspicuously marked on the outside of the shipping box. HIS
will not accept shipments not accompanied by an RMA number. You must ship or deliver the product
to HIS Freight prepaid.
What Does This Warranty Not Cover?
This warranty does not cover equipment which has been damaged due to misuse, abuse, or accident
such as: operating the equipment outside of published specifications; exposure to chemicals or gases
not covered by specified NEMA standards; displaying fixed images for long periods of time resulting
in afterimage effects; improper or unauthorized repair by anyone other than HIS or a service agency
authorized by HIS to perform such repairs; fire, flood, “acts of God”, or other contingencies beyond the
control of HIS.
HIS’ responsibility for malfunctions and defects in hardware is limited to repair and replacement as set
forth in this warranty statement. HIS shall not be liable for direct, indirect, incidental, consequential, or
other types of damages resulting from the use of any HIS product other than the liability stated above.
These warranties are in lieu of all other warranties express or implied, including, but not limited to, the
implied warranties of merchantability or fitness for a particular purpose. Some states do not allow the
exclusion of implied warranties or the limitation or exclusion of liability for incidental or consequential
damages so the above exclusions or limitations may not apply to you. You are cautioned that the
performance of this product can be affected by many factors, such as system configuration, software,
application, and operator control of the system. It is your responsibility to determine suitability of this
product for your purpose and application.
RL15F User Manual, June 2010 27
Hope Industrial Systems, Inc.
Sales and Customer Service: sales@HopeIndustrial.com
Support and Returns: support@HopeIndustrial.com
Accounting Department: accounting@HopeIndustrial.com
28 US / International
UK
1325 Northmeadow Parkway
Suite 100
Roswell, GA 30076
P.O. Box 216, Ref. 294
Widnes
WA8 2ZX
United Kingdom
Toll Free: (877) 762-9790
International: +1 (678) 762-9790
Fax: (678) 762-9789
Phone: +44 20 7193 2618
Fax: +44 20 7117 1194
www.HopeIndustrial.com
www.HopeIndustrial.co.uk
RL15F User Manual, June 2010
© 2010 Hope Industrial Systems, Inc.