User’s manual
w w w. v t e c h . c o m / h k / t e l
Model: VT2030
DECT
Table of contents
1. IMPORTANT SAFETY INSTRUCTIONS .......................1
5. TROUBLESHOOTING .................................................16
2. SETTING UP THE TELEPHONE ...................................2
6. TECHNICAL SPECIFICATIONS..................................17
2.1
2.2
2.3
2.4
2.5
Package contents ..............................................................2
Location .............................................................................2
Setting up ..........................................................................3
2.3.1
Connecting the charger .....................................3
Installing and charging the battery pack ............................4
Setting date and time.........................................................5
2.5.1
Change the Date Format ...................................5
2.5.2
Change the Time Format...................................5
2.5.3
Set the Date and Time.......................................5
3. GETTING TO KNOW YOUR PHONE ............................7
3.1
3.2
3.3
3.4
3.5
Overview of the Handset ...................................................7
Handset LCD Display Icons and Symbols .........................8
Charger............................................................................10
Navigating the menus ......................................................10
Menu map........................................................................11
4. USING ADDITIONAL HANDSETS ..............................12
4.1
4.2
Registration .....................................................................12
Make an Internal Call.......................................................12
4.2.1
Intercom Another Handset...............................13
4.2.2
Intercom the Base ...........................................13
4.2.3
Call All Handsets and Base .............................13
4.2.4
Transfer an External Call from Handset to
Handset ...........................................................14
4.2.5
Transfer an External Call from Handset to
the Base ..........................................................14
4.2.6
Transfer an External Call from the Base to
Handset ...........................................................14
4.2.7
Make a 3-way Conference Call .......................15
4.2.8
Make a 3-way Conference Call with
Call Share........................................................15
1
1.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury,
including the following:
1. Read and understand all the instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink, swimming pool).
5. Do not expose the telephone to direct sunlight or extreme cold environment. Do not put the telephone close to heating sources such as
radiators, cookers, etc.
6. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
7. Unplug this product from the wall outlet and refer servicing to VTech under the following conditions:
• When the power supply cord or plug is damaged or frayed.
• If the product does not operate normally by following the operating instructions.
• If the product has been dropped and the cabinet has been damaged.
• If the product exhibits a distinct change in performance.
8. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
9. Do not use the telephone to report a gas leak in the vicinity of the leak.
10. Use only the supplied NiMH (Nickel Metal Hydride) batteries! The operation periods for the handsets are only applicable with the default
battery capacities.
11. The use of other battery types or non-rechargeable batteries/primary cells can be dangerous. These may cause interference and/or unit
damages. The manufacturer will not be held liable for damage arising from such non-compliance.
12. Do not use third party charging bays. The batteries may be damaged.
13. Please note the correct polarity while inserting the batteries.
14. Do not immerse batteries in water, do not place in fire.
If you have questions about this product, or having difficulty with setup or operation, call our Customer Service Centre.
Customer Service Hotline: (852) 2666 5558
Technical Inquiry Hotline: (852) 2667 7433
1
2.
SETTING UP THE TELEPHONE
2.1
Package contents
The package contains the following items:
・ 1 Handset
・ 1 Charger
・ 1 AC power adapter
1 Rechargeable battery pack
1 Chinese user’s manual
1 English user’s manual
Location
For maximum coverage and reduce the interference, here are some guidelines you should consider when you place the base unit,
- place it at a convenient, high, and central location with no obstructions between the handset and base unit in an indoor environment.
- place it away from electronic appliances such as televisions, microwave ovens, radios, personal computers, wireless devices or other
cordless phones.
- avoid facing radio frequency transmitters, such as external antennas of mobile phone cell stations.
- avoid plugging it into the same circuit as other major household electrical appliances because of the potential interference. Try moving the
appliance or the base unit to another power outlet.
If the reception for a base unit location is not satisfactory, move it to another location for better reception.
Depending on the surrounding conditions as well as spatial and structural factors, the range may be reduced. The range indoors is normally
less than outdoors.
2
Setting up the telephone
2.2
・
・
・
2.3
Setting up
2.3.1
Connecting the charger
1. Plug the power supply into the charger.
2. Plug the power supply cord into the wall outlet not controlled by a wall switch.
Note:
Always use the cables provided in the box.
3
2.4
1.
2.
3.
4.
Installing and charging the battery pack
Slide off the battery compartment cover to remove it.
Place the supplied battery pack as indicated. Respect polarity.
Slide the battery compartment cover back.
Put the handset on the base and charge for 16 hours first time. A beep indicates that the handset is properly placed on the base or charger.
Setting up the telephone
Notes:
1. Use only the supplied NiMH rechargeable battery pack.
2. If the handset will not be used for a long time, disconnect and remove the battery pack to prevent possible leakage.
Battery Door
Battery
4
2.5
Setting date and time
You will need to set the correct time and date so that you can get to know when you received answering machine messages (applicable to
model with answering machine) or call list entries.
2.5.1
Change the Date Format
U/D to select HS SETTINGS.
U/D to select DATE & TIME.
Press OK and U/D to select DATE FORMAT.
Press OK and U/D to select your desired date format (DD-MM-YY or MM-DD-YY).
1. Press
and
2. Press OK and
3.
4.
5. Press OK to confirm.
2.5.2
Change the Time Format
U/D to select HS SETTINGS.
U/D to select DATE & TIME.
Press OK and U/D to select TIME FORMAT.
Press OK and U/D to select your desired time format (12 HR or 24 HR).
1. Press
and
2. Press OK and
3.
4.
5. Press OK to confirm.
2.5.3
Set the Date and Time
U/D to select HS SETTINGS.
Press OK and U/D to select DATE & TIME.
Press OK and U/D to select SET TIME.
1. Press
2.
3.
and
4. Press OK to enter the time information. The time entered will be in the format you set in Section 2.5.2.
5. Press OK to enter the date information continuously. The date entered will be in the format you set in Section 2.5.1.
6. Press OK to confirm.
5
Note:
1. If time has been set before, the current time will display, otherwise, "HH:MM" will display.
2. If date has been set before, the current date will display, otherwise, "DD-MM-YY" will display.
Your VT2030 is ready for use.
Setting up the telephone
6
3.
GETTING TO KNOW YOUR PHONE
3.1
Overview of the Handset
1. EARPIECE
2. UP
In idle mode: Press to access the call list
In menu mode: Press to scroll up the menu items
In Phonebook list/Redial list/Call List: Press to
scroll up the list
During a call: Press to increase the volume
In number editing mode: Press to move the
cursor one character to the left
3. RIGHT SOFT KEY (CLEAR/BACK/MUTE/
INTERCOM)
In main menu mode: Press to go back to idle screen
In sub-menu mode: Press to go back to previous
level
In sub-menu mode: Press and hold to go back to
idle screen
In editing/predialing mode: Press to clear a
character/digit
In editing/predialing mode: Press and hold to
delete all the characters/digits
During a call: Press to mute/unmute the microphone
In idle mode: Press to intercom another handset
or the base
4. TALK OFF
During a call: Press to end a call and go back to
idle screen
In menu/editing mode: Press to go back to
previous menu
In menu/editing mode: Press and hold to go
back to idle screen
In idle mode: Press and hold to power off the
handset
In idle mode (when the handset is powered off):
Press and hold to power on the handset
5. DOWN
In idle mode: Press to access the redial list
In menu mode: Press to scroll down the menu
items
In Phonebook list/Redial list/Call List: Press to
scroll down the list
During a call: Press to decrease the volume
In number editing mode: Press to move the
cursor one character to the right
7
6. CHARGING PINS DESIGNATOR
7. FLASH
In predialing/number editing mode: Press to
insert a flash
During a call: Press to dial a flash
8. SPEAKERPHONE
During a call: Press to turn on/off the speakerphone
In Idle mode/predialing mode/Redial list/Call
List/Phonebook entry: Press to make a call with
speakerphone
During ringing: Press to answer a call with
speakerphone
9. MICROPHONE
10. PHONEBOOK
In idle mode/during a call: Press to access the
phonebook list
11. ALPHANUMERIC KEYPAD, * (STAR), # (HASH)
Press to insert a digit/character/*/#
1 key in idle mode: Press and hold to access the
voice mail
* key in idle mode: Press and hold to enable or
disable the keypad lock
* key during a call (in Pulse mode): Press to
switch to tone mode
* key during a call: Press and hold to start
conference call (when in intercom)
# key in Idle mode: Press and hold to turn on/off
the ringer
0 key in predialing/number editing mode/during
a call: Press and hold to insert a pause
# key in Call List mode: Press to review caller's
number if applicable
12. TALK ON
In idle/predialing mode : Press to make a call
In Redial list/Call List/Phonebook entry: Press to
make a call to the selected entry in the list
During ringing: Press to answer a call
13. LEFT SOFT KEY (MENU/OK)
In idle mode: Press to access the main menu
In sub-menu mode: Press to confirm the selection
During a call: Press to access Intercom/
Phonebook/Redial List/Call List
3.2
Handset LCD Display Icons and Symbols
The LCD display gives you information on the current status of the telephone.
Getting to know your phone
Steadily on when the handset is within range of the base.
Flashes when the handset is out of range of the base or not registered to the base.
Steadily on when an intercom is in progress.
Flashes when there is an incoming internal call or being put on hold.
Off when the intercom call goes on hook.
Steadily on indicates a call is in progress.
Flashes when there is an incoming call.
Off when the phone goes on hook.
Steadily on indicates that handsfree is being used.
Off when speaker is off.
Steadily on when the telephone answering machine (TAM) is turned on.
Flashes when new TAM messages are received.
Off when the telephone answering machine (TAM) is turned off.
Steadily on indicates that the ringer is switched off.
Off indicates that the ringer is switched on.
Steadily on when an alarm is set.
Flashes when the alarm time set before reaches.
Off when the alarm is turned off.
8
Steadily on indicates that the keypad is locked.
Off indicates that the keypad is unlocked.
Steadily on when there are newly received Voice Message Waiting (VMWI) not yet read.
Off when all the new voice messages have been read.
Steadily on indicates the battery is fully charged.
Whole icon flashes when the battery performs initial charging.
Internal block icon flashes when the battery is in final charging stage.
Steadily on indicates the battery needs charging.
Flashes when low battery power level is detected.
Steadily on indicates when more characters are existed before the text currently displayed.
Off indicates when no character is existed before the text currently displayed.
Steadily on indicates when more characters are existed after the text currently displayed.
Off indicates when no character is existed after the text currently displayed.
Steadily on indicates when more menu items are existed before the menu item currently displayed.
Off indicates when no more menu items are existed before the menu item currently displayed.
Steadily on indicates when more menu items are existed after the menu item currently displayed.
Off indicates when no more menu items are existed after the menu item currently displayed.
Press to select more menu options if applicable.
(MENU)
OK
Press to confirm the current selection if applicable.
Steadily on when new TAM message/new call is received in TAM message list/call list.
Off when new TAM message/new call has been read.
(INT)
(BACK)
Press to conduct Intercom call when idle.
Press to go back to previous menu level or cancel the current action if applicable.
Press to clear a character or stop the alarm if applicable, press to mute/unmute during a call.
9
3.3
Charger
Charging cradle
Getting to know your phone
3.4
Navigating the menus
1. Press
2. Press
3. Press
4. Press
.
U/D to scroll through the menu.
/OK to open a sub-menu or validate an option.
]/ RIGHT SOFT KEY to go back to previous menu level or cancel an action.
10
3.5
Menu map
In idle mode, press
Key Press
/OK will firstly access the Call List menu. Refer to the following for the menu structure.
/ OK
U/D
U/D
U/D
U/ D
U/D
Main Menu
CALL LIST
PHONEBOOK
BS SETTINGS
HS SETTINGS
Sub menu
Review Call List
Review
phonebook list
Under a selected
Call List entry:
ADD TO PB
DELETE
DELETE ALL
DETAILS
CATEGORY
Under a
phonebook
entry:
ADD
VIEW
EDIT
DELETE
DELETE ALL
PB STATUS
BS RINGER
RING VOLUME
LANGUAGE
DELETE HS
FLASH TIME
CHANGE PIN
CALL SHARE
ALARM
PIN?
RING SETUP
TONE SETUP
LANGUAGE
RENAME HS
HS DISPLAY
AUTO ANSWER
DATE & TIME
11
U/D
REGISTRATION DEFAULT
PIN?
U/D
ANS. MACHINE
MSG PLAYBACK
DELETE ALL
MEMO
TAM ON/OFF
TAM SETTINGS
ANSWER MODE
OGM SETTINGS
ANSWER DELAY
RECORD TIME
REMOTE ACC.
COMPRESSION
BS SCREENING
CHANGE PIN
4
USING ADDITIONAL HANDSETS
You can add new VT2030 accessory handsets to your VT2032 system, but each device must be registered with the telephone base before use.
Up to five handsets can be registered to the same base. When first purchased, each expansion handset shows "NOT REGISTERED". You may
need to charge the handset before registering to the telephone base.
4.1
Registration
1. Press
and
U/D on the handset to select REGISTRATION.
2. Press OK and select the destination base you would like to register to.
3. Press OK and you are requested to enter the 4-digit system PIN.
4. Enter the 4-digit system PIN.
5. Press OK and go ahead with the following procedures using the base.
Using the VT2032 base:
6. Press and hold G on the base station for about five seconds, the base station is entered into registration mode.
If the handset registration is successful, you will hear a confirmation tone and the
will stop flashing. The handset will automatically be
allocated the next available handset number. This handset number is shown in the handset display in standby mode. If the handset registration
is unsuccessful, the
will still flash.
4.2
Make an Internal Call
This feature is applicable when there are at least two registered handsets or one handset and base registered in the system. It allows you to
make internal calls, transfer external calls from one handset to another handset or from one handset to the base and make conference calls. If
the called handset or base is not answered within 60 seconds, the called handset or base will stop ringing and the calling handset will return to
standby mode.
12
Using additional handset
Using a VT2030 accessory handset:
4.2.1
Intercom Another Handset
1. In idle mode, press
]/ RIGHT SOFT KEY and the numbers of the registered handsets and base will display except the calling handset.
2. Enter the desired handset number to intercom with.
3. The called handset rings and press
T on the called handset to establish the internal call.
Note:
If only two handsets are registered to the base station, press
4.2.2
]/ RIGHT SOFT KEY will call another handset immediately.
Intercom the Base
1. In idle mode, press
2. Press
]/ RIGHT SOFT KEY and the numbers of the registered handsets and base will display except the calling handset.
7 to call the base.
3. The called base rings and press
s on the called base to establish the internal call.
Note:
If only one handset and base are registered in the system, press
4.2.3
Call All Handsets and Base
]/ RIGHT SOFT KEY and the numbers of the registered handsets and base will display.
9 to ring to all registered handsets and base.
1. In idle mode, press
2. Press
13
]/RIGHT SOFY KEY will call the base immediately.
4.2.4
Transfer an External Call from Handset to Handset
During an external call:
1. Press
and
U/D to select INTERCOM.
2. Press OK to select the desired handset to intercom with.
3. The external call is put on hold automatically and the called handset rings.
4. Press
T on the called handset to establish an internal call.
O on the calling handset or put the calling handset on the charging cradle to end the current call with the external party.
6. The external call is transferred to the called handset.
4.2.5
Transfer an External Call from Handset to the Base
During an external call:
1. Press
and
U/D to select INTERCOM.
2. Press OK to select the base to intercom with.
3. The external call is put on hold automatically and the called base rings.
4. Press
5. Press
s on the called base to establish an external call.
O on the calling handset or put the calling handset on the charging cradle to end the current call with the external party.
6. The external call is transferred to the called base.
4.2.6
Transfer an External Call from the Base to Handset
During an external call on base:
1. Grab off the handset from base charging cradle, the external call on the base will be transferred to handset automatically, and the base will
go to idle.
14
Using additional handset
5. Press
4.2.7
Make a 3-way Conference Call
The conference call feature allows one external call to be shared with two handsets (in intercom). The three parties can share the conversation
and no network subscription is required.
During an external call:
1. Follow Steps 1 to 4 in section 4.2.4.
2. Press and hold
- on the calling handset to establish the conference call.
Note:
Any handset hangs up during a conference call will leave the other handset still in connection with the external call.
4.2.8
Make a 3-way Conference Call with Call Share
If you turn on the call share function (please refer to the user's manual of VT2032 for details), you can join the conversation with your handset
or base easily as following when the other handset is on an external call.
During an external call:
1. Press
OR
Press
s on the base to establish the conference call if any handset has answered the call.
T or S on the handset to establish the conference call if another handset or the base has answered the call.
Note:
Any party (base or handset) hangs up during a conference call will leave the other party still in connection with the external call.
15
5.
TROUBLESHOOTING
If you have difficulty with your phone, please try the suggestions listed below. Please also check the user's manual of VT2032 for more detailed
troubleshooting items.
Problem
"PLEASE SET TIME" is displayed.
T
When connected to a PBX, no and/or
Dialing prefix is needed.
wrong connection after dialing.
a. Base station may be out of range.
"OUT OF RANGE" is displayed.
b. Base station may not be connected to mains.
Service may not be activated or wrong operation
The call does not work.
or wrong setting
No display.
Empty battery
Solutions
Set the date and time from handset menu.
a. Check the connections. Unplug and plug back
in the mains. Check that the telephone line cord
has been plugged into the base station and the
phone socket.
b. Check the base station plug and the 220V plug
(remove and plug-in).
c. Wait until the line is unoccupied.
d. Use the original connection cord.
Insert the dialing prefix.
a. Reduce the range.
b. Connect base station to mains.
Check your Subscription with network
Recharge battery
Please contact the technical support of the telephone service provider for further information.
This telephone is not equipped with a grounding function! Therefore some of the functions may be limited when used in PBX systems.
For technical support, please call VTech Technical Inquiry Hotline 852-2667 7433.
16
Troubleshooting
No dialing tone when pressing
key
Cause
Date or time may not be set.
a. The connection cord of the base station may
not be plugged in.
b. The adapter cord may not be plugged in
correctly in the base station.
c. The line may be busy, as another handset may
be used.
d. Wrong connection cord (no Euro AS)
6.
TECHNICAL SPECIFICATIONS
Basic Information
Dimensions
Handset: 212 x 51.8 x 26.8mm
Charger: 129.8 X 100.8 X 75.1mm
Weight
Handset: 130.8g
Charger: 102g
Power consumption
Charger: <1.8W
Valid range
Indoor: 50m
Outdoor: 300m
Handset Operating Time
Standby time: 100Hours
Talk time: 10Hours
RF Parameter
Transmission Power
Handset: <25dBm
Frequency
1881.792 -1897.344 MHz
Number of Channels
10
Supply Power
Charger:
Input AC100-240V; output DC6V; 450MA adaptor
Handset
2 x NIMH; 2/3 AAA; 2.4V; 400MAH rechargeable batteries
17
Customer Service Centre
Suite 1601, Lever Tech Centre, 69-71 King Yip Street,
Kwun Tong, Kowloon, Hong Kong.
Customer Service Hotline: (852) 2666 5558
Technical Inquiry Hotline: (852) 2667 7433
Distributed in Hong Kong by: VTech Telecommunications Ltd.
91-004990-010-100