Product Guide
Index
introduction............................................................................................................................................3
THE RADIOELECTRIC SPECTRUM.................................................................................................................4
product.......................................................................................................................................................5
Filters....................................................................................................................................................................................................6
Plug-in and easy F format........................................................................................................................................................................................... 6
Microcavities filter........................................................................................................................................................................................................... 7
Intelligent aerials..............................................................................................................................................................................8
DAT HD BOSS 790............................................................................................................................................................................................................ 9
V HD 790............................................................................................................................................................................................................................10
Q-BOSS................................................................................................................................................................................................................................10
INNOVA BOSS...................................................................................................................................................................................................................11
Amplification.................................................................................................................................................................................. 12
Nanokom masthead amplifiers..............................................................................................................................................................................12
Setback amplifiers.........................................................................................................................................................................................................13
Launch amplifiers..........................................................................................................................................................................................................13
Programmable amplifier Avant3............................................................................................................................................................................14
Programmable amplifier Avant HD......................................................................................................................................................................15
Single channel amplifiers T12.................................................................................................................................................................................16
Distribution..................................................................................................................................................................................... 18
Certified coaxial cable.................................................................................................................................................................................................18
New CAI RG-6 Approved cable...............................................................................................................................................................................18
PRO easyF connectors................................................................................................................................................................................................20
Cable leads........................................................................................................................................................................................................................21
Outlet plates.....................................................................................................................................................................................................................22
Splitters and taps...........................................................................................................................................................................................................22
RECEPTION AND ADAPTION DTT...............................................................................................................23
ZAS HD adaptor..............................................................................................................................................................................................................23
Transmodulation COFDM/COFDM regenerator............................................................................................................................................24
MEASUREMENT...........................................................................................................................................25
H60 The perfect tool to analyze the new digital dividend................................................................................................ 25
Introduction
The path initiated with the deployment of DTT will
take a step further with the development of the digital dividend a process which will establish the technical conditions for the allocation of the 800 MHz band
(channels 61- 68) in the EU for the introduction of
advanced mobile phone services and mobile Internet
(Long Term Evolution - LTE).
The use of channels 61 to 68 for mobile services responds, on one hand, to an intent to harmonize the use
of this band across Europe and, on the other, to reduce
the cost of the network infrastructure (less cells required, better penetration and better coverage at these
frequencies).
Mobile phone connections will represent 80% of the
broadband connection in the year 2014. This spectrum
must be harmonized in the 800 MHz band in order to
develop the maximum potential of LTE technology and
make it available to societies growing demand for services.
The release of the digital dividend must be completed
in Europe before the 1st of January 2015. Some governments, like the UK, have already announced that these
frequencies will be released during the first half of 2013.
In some countries, the release of the digital dividend
could face an added complexity since DTT channels
will need to be rellocated to channels between 21 and
60. So during this transition retuning will be required
by the end user and maybe adaption of the installation.
The planification for the rellocation of frequencies is
normally regulated by a government agency and will
be part of an on going plan; in the UK the regulator is
OFCOM.
For the installers of domestic and commercial TV reception systems, the digital dividend is a challenge. As an
industry leader, Televes has worked hard to give the
professional installer all the support required, not only
with products but also with technical support.
3
The radioelectric spectrum
uhf-SPECTRUM
The UHF band is currently exclusively used by broadcasted DVB-T/T2 transmissions. However, this will change with the release of
the radioelectric spectrum between channels 61 and 68 for the allocation of mobile broadband services, also known as 4G.
DVB-T/T2
LTE
Downlink
UP link
DL DL DL DL DL DL
UL UL UL UL UL UL
...
21
22
23
24
57
58
59
470 MHz
60
790 MHz
862 MHz
lte SPECTRUM
The frequency spectrum between 790 and 862 MHz will be allocated to the new LTE services.
LTE development reserves only a 1 MHz guard band between LTE and the possible DVB-T/T2 services located at channel 60.
We should be able to differentiate between LTE downlink signals and LTE uplink signals.
uLTE uplink signals
uLTE downlink signals
These are the download transmissions from the mobile
network to the mobile terminal and can be received by
DTT aerials.
Signals being transmitted from the LTE user terminal that
will be received as interfering signals by the receivers
integrated in the TV’s or the stand alone set top boxes.
Depending on the amplification system being used in
the installation (broadband amplification, programmable
amplifiers or single channel amplifiers) a protection ratio
can be established for channels 60 and 59 plus the rest of
the channels, bearing in mind the small guard interval (1
MHz) between LTE and DTT.
Both for domestic and communal system the uplink
signals could filter into the distribution system through
a poorly screened cable, outlet plate or connector, the
interference could even cause pixelization.
Domestic systems will present similar problems, as they
are exposed to LTE downlink signals that can reach the
amplification, these will normally be broadband and
hence more sensitive to interference.
Exiting
DVB-T signal
LTE Tx
Influence of LTE over DTT
790-791 791-796 796-801 801-806 806-811 811-816 816-821
821-832
832-837 837-842 842-847 847-852 852-857 857-862
Guard
band
Downlink
Duplex gap
Uplink
1 MHz
30 MHz (6 blocks of 5 MHz)
11 MHz
30 MHz (6 blocks of 5 MHz)
4
LTE READY PRODUCTS
Product
The deployment of LTE transmitters will, presumably, be done
using the same locations as the current UMTS (3G) and/or GSM
networks, so they will be in proximity with TV reception systems,
most of these TV systems will have broadband amplification. In
this scenario, the TV reception systems will simultaneously receive DTT and LTE transmissions. This will generate intermodulation signals to a greater or lesser extent depending on many
different factors (level of the received signals, amplification, DTT
channels received, etc.). The intermodulation interference will
travel through all the distribution components until it reaches
the set top box.
In anticipation to LTE deployment, Televes has participated in trials and has done in depth analysis of the implications that this
technology will have on the reception of broadcasted TV.
As the result of the work carried out by our R&D team a company
leader in the industry, Televes has developed a complete range
of products specifically designed to minimize the potential
of LTE interference over DTT services. All these products will
carry the LTE Ready stamp, registered by Televes.
RANGE OF PRODUCTS SPECIFICALLY DESIGNED FOR LTE
FILTERS
PROGRAMMABLE AMPLIFIERS
403101 LTE FILTER “F” 470...774MHz (Ch21-58)
532740AVANT3
403401 LTE FILTER “F” 5...790MHz (Ch21-60) SELEC.
532840 AVANT HD
404411 BLIST. LTE FILTER “IEC” 470...774MHz (Ch21-58)
SINGLE CHANNEL AMPLIFIERS
404412 BLIST. LTE FILTER “IEC” 5...790MHz (Ch21-60) SEL.
508012 IF BAND AMPLIFIER T12
405101 LTE FILTER “EasyF” 470...774MHz (Ch21-58) OUTDOORS
508112 BI BAND AMPLIFIER T12
BI
405401 LTE FILTER “EasyF” 5...790MHz (Ch21-60) SELEC. OUTD.
508212 FM BAND AMPLIFIER T12
FM
403301 LTE MICROCAVIT. FILTER “F” 5..790MHz SEL.
509912 DAB BAND AMPLIFIER T12
DAB
ANTENNAS
508312 BIII BAND AMPLIFIER T12
149901 DAT HD BOSS 790 ANT.(Ch21-60) G32dBi BOXED
508712 LOW S BAND AMPLIFIER T12
SAT
BIII
SB LOW
149101 V HD 790 TERR.ANT. UHF(Ch21-60) G15dBi BOXED
508812 HIGH S BAND AMPLIFIER T12
SB HIGH
130201 IINNOVA BOSS ANT. (Ch21-69 or Ch21-60) G25dBi
508912 HYPERBAND AMPLIFIER T12
HYPERB.
Q-BOSS
509812 SELECTIVE SINGLE CHANNEL AMPLIFIER UHF
561901 Q-BOSS 790 “EasyF”Ch21-60 G15dB Vo102
508612 SINGLE CHANNEL AMPLIFIER
UHF
562001 Q-BOSS 774 “EasyF”Ch21-58 G12dB Vo100
549812 SWITCHED PSU T12
MASTHEAD AMPLIFIERS
509512 SEL. SINGLE CHANNEL AMP WITH AGC T12
UHF
561501 MAST AMP.12..24V 3I/1O B3/U-FMmx-SATmx USOS
509712 SINGLE CHANNEL AMP. WITH AGC T12
UHF
561601 MAST AMP. 12..24V 3I/1O U-Vmix-SATmix USOS
OUTLET PLATES
561701 MAST AMP.12..24V 3I/1O U-U-Vmix
522610 OUTLET PLATE.47..2150MHz 1-1,5dB+DC
561801 MAST AMP. 12..24V 3I/1O BIII-U-FMmix USOS
523110 THROUGH OUTLET PLATE 5...790MHz TV-FM 11-29dB
SETBACK AMPLIFIERS
SCREENED COAX LEADS
562701 DOM.AMP.1O VHF/UHF G13/24dB USOS + DC
431001 COAX LEAD “IEC”ELBOW.M-F WHITE 1,5M
562711 DOM.AMP.1O V/U G13/24dB USOS+DC W/O PSU
431002 COAX LEAD “IEC”ELBOW.M-F WHITE 2,5M
562702 DOM.AMP.2O VHF/UHF G10/21dB USOS + DC
SPECTRUM ANALYZER
562712 DOM.AMP.2O V/U G10/21dB USOS +DC W/O PSU
5960
H60 ADVANCE (FULL HD + CI+F.O.+EXTENDED
562703 DOM.AMP.2O+TV VHF/UHF G9/20dB USOS + DC
SPECTRUM 5...3300 MHz)
562713 DOM.AMP.2O+TV V/U G9/20dB USOS + DC W/O PSU
596005 H60 ADVANCE (FULL HD + CI+EXTENDED SPECTRUM
LAUNCH AMPLIFIERS
562301 MINIKOM AMP.5/1”EasyF” FM-V-U-21..35-39..60/69F
5...3300 MHz+SELECTIVE F.O)
562302 MINIKOM AMP.5/1”EasyF” FM-V-U-21..32-36..60/69
562401 MINIKOM AMP.MATV 4I/1O “EasyF” FM-V-U-U
562501 MINIKOM AMP.MATV 3I/1O “EasyF” FM-V-U
562601 MINIKOM AMP.SMATV 4I/1O “EasyF” FM-V-U-SAT
5
LTE FILTERS 58 and 60
Televes has designed two types of filters with different rejection and performance depending if there are TV services over channel
58 or not. Once decided the type of filter based on the location of the channels, we will need to choose the format.
plug-in indoors (f & iec)
EASY F outdoors
The most reliable and quick connection
Reduces the installation
time by 50%
Built-in system
404411
404412
You will never require extra
connectors
403101
403401
REF
FILTERS
405101
LTE 1I/1O EasyF Ch 21-58
403101
LTE 1I/1O F Ch 21-58
404411
LTE 1I/1O IEC Ch 21-58
405401
LTE 1I/1O EasyF Ch 21-60
403401
LTE 1I/1O F Ch 21-60
404412
LTE 1I/1O IEC Ch 21-60
403301
CAVITIES 1I/1O F Ch 21-60
Pass band
(MHz)
Rejected band
(MHz)
Pass band
attenuation (dB)
Rejected band
attenuation (dB)
470 - 774
791 - 862
<3
(7@774MHz)
>25
5 - 790
793 - 821
405101
405401
<1
(5@790MHz)
>20
<0,5 (2@790MHz)
The quality in the filter’s response can only be appreciated with graphs as the ones below, where the performance of the filter in
the highLTE57
UHF channels can be seen in detail.
LTE60 Grafica 1
G (dB)
G (dB)
0
0
-5
-5
-5
-10
-10
-10
-15
-15
-15
-20
-20
-20
-25
-25
-25
-30
-30
-30
-35
-35
-35
-40
-40
-40
-45
-45
G (dB)
0
-50
C58
C60
700 716,2 732,4 748,6 764,8 781
797,2 813,4 829,6 845,8 862
F (MHz)
C58 LTE filter rejects signals from 774MHz onwards. Specifically recommended for
DTT installations with multiplex below channel 58.
-50
C57
C60 C57
C60
-45
-50
(MHz) 862
700 716,2 732,4
748,6 732,4
764,8 781
700 716,2
748,6 797,2
764,8 813,4
781 829,6
797,2 845,8
813,4 862
829,6F 845,8
F (MHz)
C60 LTE filter rejects signals from 782MHz onwards. Specifically recommended for DTT
installations with multiplex channels 59 or 60.
Grafica 2
The filters for LTE can be designed using different technologies:
G (dB)
C58
0
C60
LC. Using discrete components (L, C) important rejection to the
interference band could be achieved but it will increase the insertion losses in the DTT band. Its use could lead to having to readjust
the amplifiers in the system.
SAW
-5 Filters. The surface wave filtering (SAW) achieves high
rejection
in small frequency intervals. It generates high insertion
-10
losses-15
and why they need to be combined with an amplifier, which
complicates its design and increases its cost.
Ceramic resonators. The ceramic resonating filters resolve the
problems with the insertion losses of the LC filters. If the resonators are not of high quality, variations in temperature will cause
variations in the rejection and insertion losses in the DTT channels
near LTE (channels 59 and 60).
-25 filters. They are formed by three coupled transmission
Cavity
lines, -30
which are located resonant metal cavities. They achieve optimum-35rejection characteristics (25-30 dB and even more), whilst
maintaining
minimum insertion losses (< 1 dB in the DTT band with
-40
2 dB typical in the high UHF channels 59, 60).
-20
-45
-50
700 727
742
757
772
787
802
6
LTE READY PRODUCTS
3
817
832
847
862
F (MHz)
Grafica 1
G (dB)
C57
0
C60
-5
-10
-15
-20
-25
-30
PATENTED
MICROCAVITIES FILTER (F FORMAT)
-35
-40
-45
-50
700 716,2 732,4 748,6 764,8 781
403301
G (dB)
802
F (MHz)
C60
-5
-10
-15
-20
The microcavities filter achieves outstanding performance
with temperature variation and its robust construction
makes it very resistant to vibration, the ideal component for
the rejection of the LTE interference, whilst preserving the
reception of DTT. They could be used either as a preventive
measure or a mitigation solution.
-50
C60
C58
0
Televes has achieved it with its microcavities filter (patented
system) and is implementing the technology in a small chassis
(10 cm x 5 cm) and with a weight of less than 250 grams, which
makes it suitable for internal or external use. In order to achieve
this, Televes uses what is called micro-cavities, in which the
resonant elements of high quality factor (Q) are allocated.
C57
F (MHz)
Grafica 2
Normally these types of filters are bulky and heavy, hence
the reason why they were never used in MATV solutions,
restricting their use to broadcasting solutions or very high end
MATV headends.
C57
797,2 813,4 829,6 845,8 862
-25
-30
-35
-40
-45
700 727
742
757
772
787
817
832
847
862
Microcavities LTE C60 filter
it rejects signals above 782MHz with minimum insertion losses
3
DL DL DL DL DL DL
C60
DL DL DL DL DL DL
DTT signal on aerial + LTE
Televes’ microcavities
filter
FILTRO DE MICROCAVIDADES
Other filters
REF.403301
5 - 790 MHz
Insertion loss
< 0,5dB
FILTRO DE MICROCAVIDADES
REF.403301
5 - 790 MHz
Insertion loss
< 0,5dB
Filtered DTT signal
C57
C57
Filtered
DTT C60
signal.
C57
C60
C60
C57
Channel 60 not affected
Channel 60 affected
Headend
Headend
C57
C57
C60
C60
Balanced and clean DTT signal
C60
C57
C57
C60
C60
DTT signal affected by intermodulation
In the presence of channel 60, depending
on the chosen filter, it could be that the
headend (amplifier) is unable to equalize the output level of all the available
channels.
In the example figure we show channel
60 being received by the aerial and balanced with respect to the rest of the available channels. If the filter used is not a
micro-cavities filter ref.403301, it is more
likely that the headend will be unable to
achieve the same output level for channel
60 as it does for the rest of the channels.
Both for broadband amplifiers or single
channel amplifiers, the increase in gain
in the amplifier to overcome the losses in
the filter could result in the generation of
intermodulation products.
7
Intelligent antennas
Evolution of the species
Conventional electronic antennas are nothing more than
basic ACTIVE AERIALS, this is an aerial with an amplifier which
in many cases has an unacceptable noise figure.
Televes’ antennas with BOSSTech are
not active aerials. The intelligent device built into
the antenna which can be activated or not depending on the
requirements of the installation, it automatically regulates the
gain to provide the TV with the best signal quality.
ACTIVE aerials could cause problems that render them
useless in the current scenario with DTT and in the future
for co-existence of DTT with LTE/4G.
Whilst an active aerial will saturate in the presence of a
LTE/4G signal, the BOSSTech will regulate its gain to avoid
saturation, several radiated test where DTT and 4G coadjacent
signals were received by a BossTech antenna. The option
of blocking the power to the antenna can also be used in
extreme cases.
CONVENTIONAL ACTIVE AERIAL
The BOSSTech device allows the installer and the end user
to competely forget about the signal level in reception,
resolving those problems caused by level adjustment or the
signal fluctuation that could occur during the life span of the
installation.
BOSSTech ANTENNA
DTT
DTT
SATURATED
SIGNAL
PERFECT
SIGNAL
Installing a Televes BOSSTech antenna assures the continuity in quality of service and the best possible
performance of the system, even with LTE/4G.
8
LTE READY PRODUCTS
INTELLIGENT ROOF TOP ANTENNA DAT HD boss 790
NEW
This antenna has been designed to optimize rejection
to the LTE band whilst keeping the reception
characteristics in the UHF TV band , it is an evolution
of the DAT HD BOSS antenna with angular triple array
patented by Televes.
The antenna incorporates the BOSSTech device,
with improved electronic performance.
NEW ASSEMBLY SYSTEM
Rotarory folding mechanism
Cam mechanism for the assembly of the reflectors
1
2
The new DAT incorporates a new
folding mechanism of the
directors and a cam mechanism
in the reflector
The new folding mechanism of the directors not only simplifies the
assembly of the antenna but also optimizes its transport and storage.
SPECIFICATIONS
Ref.149901
Mode
Passive
Bandwidth
MHz
Maximum gain
dBi
Noise figure
dB
Powering
Maximum consumption
17
32 max
G (dBi)
1.2 typ
Self adjustable
dBµV
>75
<75
V
0
12-24
0
45 (24V)/35(12V)
-5
mA
º
Wind load
N
0
30
120 (130km/h)
165 (150 km/h)
BOSS
DESACTIVADO
PASSIVE
BOSS
30
-
Lobe width
BOSS
ACTIVADO
ACTIVE
BOSS
35
-
Output level
Recommended input
level
Active
470-790 (Ch 21-60)
25
20
15
10
5
-10
-15
-20
450 500
550
600
650
700
750
800 850 900
950
F (MHz)
9
ROOF TOP ANTENNA V HD 790
Antenna specifically designed to optimize the reception of
channels 21 to 60 whilst achieving maximum out of band
rejection for the 4G/LTE band. Its clever design allows the
antenna to achieve high levels of out of band rejection with
no built-in filtering.
15
10
5
0
-5
-10
Confederation of Aerial Industries.
-15
specifications
Ref. 149101
-20
Made of high grade aluminium and plastics and very easy to
assemble, the V790 has been designed to withstand the test
of time.
Bandwidth
MHz
470 - 790 (Ch 21-60)
Gain
dBi
15
F/B ratio
dB
> 23
Wind load
N
93 (@ 130 km/h)
128 (@ 150 km/h)
Q-BOSS
The only device capable of transforming any aerial into a
BOSSTech antenna, converting your active or passive aerial
into an intelligent device.
GENERIC AERIAL WITH NO Q-BOSS
ADAPTED AERIAL
DTT
DTT
4G
DTT
DTT
100% PROTECTED
4G
Q-Boss - Easy F
Ref.562001 Q-BOSS 774 Ch21-58
Ref.561901 Q-BOSS 790 Ch21-60
10
LTE READY PRODUCTS
POWERING (V)
12...24V
GaIN (dB)
OUTPUT LEVEL (dBuV)
DIN45004B
UHF
UHF
12
100
15
102
INTELLIGENT SET TOP ANTENNA INNOVA BOSS
360º
SPECIFICALLY DESIGNED FOR THE RECEPTION OF DTT
INDOORS.
The best possible DTT reception, HD services
and 3D TV indoors.
Incorporates the BOSS technology that automatically
regulates the output signal, which ensures the optimum
reception in areas with intermittent reception, whilst
eliminating the interferences caused by people moving
around the room in which its installed.
Connections depending on type of TV set
Its exceptional radiation lobe of 360º allows this set top
antenna to be installed in any position with no worries
about its orientation.
Plug&Play.
 No need to be orientated:
 LTE Ready.
431001
5124
SCART 4319
HDMI 495401
Ref. 130201
specifications
Bandwidth
MHz
Pos. 60: 470 - 790
Pos. 69: 470 - 862
Maximum gain
dBi
25*
Noise figure (typ.)
dB
3
Maximum consumption (5 ... 12V )
mA
40
IP
20
mm
215 x 102 x 105
gr
350
Protection index
Dimensions
Weight
431001
* Self regulated gain for high input levels.
The Innova Boss incorporates a easy switch ON-OFF
that allows its user to turn ON or OFF the protection against
LTE interference as necessary.
11
Amplification
MASTHEAD AMPLIFIERS
G (dB)
55
50
45
40
35
30
25
20
Optimized
for the band between channels 21 and 60.
15
Incorporates
LTE Switch ON/OFF.
10
5
Incorporates
DC pass Switch (ON/OFF).
400 460
520 580 640 700 760 820 880 940 1000
F (MHz)
Improved noise figure performance (NF).
Once the output level has been adjusted through a
potentiometer located on the front, the amplifier will maintain
this level by means of an automatic regulation system.
USER SELECTABLE OUTPUT SIGNAL
G (dB)
35
30
25
20
15
10
5
0
-5
-10
-15
Ref.
400 460
520 580 640 700 760 820 880 940 1000
DeSCRIPTION
NOISE FIGURE (dB)
UHF
561501
(U+BIII)dc-(FM+BI)mix-FImix
561601
UHF-VHFmix-FImix
561701
561801
U1dc-U2-VHFmix
U-BIII-(FM+BI) mix
12
LTE READY PRODUCTS
VHF
F (MHz)
GaIN (dB)
UHF
VHF
MAX. OUTPUT
LEVEL (dBuV)
UHF
REMARKS
VHF
1.5
3.5
31
18
103
103
Auto. indep. Regulation U and BIII.
Indep. Reg. Vout U and BIII
DC (U+BIII) ON/OFF
BIII:174-253 MHz
LTE Filter ON/OFF
1
-
31
-1
103
-
Auto. Regulation UHF
Vout regulation U
VHF:47-253
LTE Filter ON/OFF
-
Indep. Atten. U1 and U2
DC U1 ON/OFF
VHF:47-253
LTE Filter ON/OFF
103
Auto. Indep. Regulation U and BIII
Indep. Reg. Vout U and BIII
BIII:174-253 MHz
LTE Filter ON/OFF
6
1
-
3
27
31
-1
18
103
103
SETBACK AMPLIFIERS
Optimized for the band between channels 21 and 60.
Remotely powered through any of its outputs.
Detachable PSU, allowing flexibility in its location.
USER SELECTABLE OUTPUT SIGNAL
Once its output level has been set by means of a potentiometer
located on the front, the amplifier will keep this level by means
of an automatic gain regulation system.
Ref.
DeSCRIPTION
MAX. OUTPUT LEVEL (dBuV)
DIN45004B
GaIn (dB)
UHF
VHF
UHF
VHF
562701
AS VHF/UHF 1E/1S
24
13
106
98
562702
AS VHF/UHF 1E/2S
21
12
103
95
562703
AS VHF/UHF 1E/2S+TV
20
9
102
94
562711
AS VHF/UHF 1E/1S
24
13
106
98
562712
AS VHF/UHF 1E/2S
21
12
103
95
562713
AS VHF/UHF 1E/2S+TV
20
9
102
94
NOTes
Detachable PSU included
Common auto. regulation VHF/UHF
LTE Filter ON/OFF DC IN ON/OFF
Detachable PSU not included
Common auto regulation VHF/UHF
LTE Filter ON/OFF DC IN ON/OFF
LAUNCH AMPLIFIERS
Optimized for the band between channels 21 and 60.
New compact design.
Switch mode PSU, best guarantee of low consumption,
and detachable.
G (dB)
55
50
45
40
35
30
25
20
15
10
5
400 460
520 580 640 700 760 820 880 940 1000
Ref.
Description
562301
562302
F (MHz)
Gain (dB)
MAX. OUTPUT LEVEL (dBuV)
UHF
VHF
FI
UHF
VHF
FI
AS FM-VHF-BIV(21-35)-BV(39-60)-UHF
37/27
30/20
-
117
113
-
AS FM-VHF-BIV(21-32)-BV(36-60)-UHF
37/27
30/20
-
117
113
-
562401
AS FM-VHF-UHF1-UHF2
37/27
30/20
-
117
113
-
562501
AS FM-VHF-UHF
40/30
33/23
-
117
113
-
562601
G (dB)
AS FM-VHF-UHF-FI
40/30
30/20
35-42
112
103
121
NOTes
BI is not amplified
VHF: 174-400 MHz.
Switchable LTE filter
35
30
25
20
15
10
13
Amplification
PROGRAMmABLE amplifier AVANT 3
Programmable filtered launch amplifier for domestic or/and
communal systems. Incorporates 5 programmable filters with
variable bandwidth, and can isolate the DTT signal from LTE
interferences.
Main features
Five or seven channels per filter.
Self adjustable thanks to an AGC (Automatic Gain Control)
in each filter, with an LED to indicate if we have enough
input level in UHF.
VHF input with expanded bandwidth, designed for the
combination of services generated from signal processing
headend.
Expandable system; extra Avant3’s can be linked.
p 532740
Ease of programming by means of handheld programmer
and/or software.
Switch mode PSU with low consumption and high
efficiency.
inputs
parameters
Bandwidth
MHz
Filters per input
Number of channels per filter
output
UHF1
UHF2
BI / FM
VHF
IN MIX
OUT
470 - 790
470 - 790
47-68 / 87 - 108
111-406
47-406 / 470-790
470-790
5-0
2-3
-
-
-
-
1-5 (21-30) / 1-7(31-69)
-
-
52 ± 3
32 ± 2 / 15 ± 2
35 ± 2
2±2
(UHF1, UHF2-UHF)
-
Gain regulation
dB
-
0 - 18
0 - 15
3±3
(INMix-OUT)
-
AGC’s margin per filter
dB
0 - 20
-
-
-
-
Ouput level regulation
dB
15
-
-
-
-
Max. Input level
dBμV
95
-
-
-
-
Max. Output level 2 DTT Ch (typ.)
dBμV
113
111
111
111 / 113
-
Output level DIN 45004B (typ.)
Output level
IMD3 (2CH-60dB) (typ.)
Rejection
dBμV
116
114
114
114 / 116
-
dBμV
113
111
111
111 / 113
-
dB
20 (± 16MHz)
20 (± 206MHz)
15 (± 40MHz)
-
-
7
7
7
-
-
-
-
-
-
Gain
dB
Noise figure (typ.)
dB
Line power (1) (12Vdc)
mA
Powering
V~
196 - 264
Maximum current
mA
80
Maximum power
W
Protection Index
Temperature range
(1) Controlled by switch at the back.
14
LTE READY PRODUCTS
50
50
9
IP20
ºC
-5 a +45
PROGRAMMABLE AMPLIFIER AVANT HD
Programmable filtered launch amplifier for large domestic
or communal systems, characterised for its selectivity and
capacity to balance incoming signals.
Main features
Easy to install and program.
High output level and input dynamic margin.
External programming.
Very flexible configuration.
Allows to clone configuration between devices.
Access to configuration can be blocked via password.
Low consumption.
p 532840
Inputs
Band
Gain
Filter configuration
UHF1
MHz
UHF3
470 - 790
FM
BI
87 - 108
174 - 260
Auto
(máx. 44 ± 3)
-
47-790 MHz
47 - 370
IF SAT
370 - 790
10
0
0
9
0
1
-
-
-
-
-
7
2
1
-
-
-
-
-
6
3
1
-
-
-
-
-
5
3
2
-
-
-
-
-
Auto (máx. 51 ± 3).
Auto
Auto
(máx. 36 ± 2) (máx. 39 ± 2)
-
950 - 2150
Auto
(máx. 41 ± 3)
-
dB
Nº
UHF2
42 ±2 - 45 ±2
-
Number of channels per filter
Nº
0 - 5 **
-
-
-
-
-
Slope control
dB
0 - 9 **
-
-
-
-
0 - 12
dBμV
60 - 105
60 - 85
62 - 87
69 - 73
70 - 74
-
dB
0 - 20 *
0 - 25 - OFF*
0 - 25 - OFF*
-
-
0 - 24 - OFF*
Optimum input margin
Gain regulation
Manual gain regulation
dB
± 9 (per filter)
±9
±9
-
-
-
Output level ***
dBμV
121
115
115
115
121
125
Output level regulation
100 - 115
dBμV
100 - 115
90 - 105
95 - 110
95 - 110
Noise figure
dB
9 typ.
10
10
-
Rejection
dB
20 (±16 MHz)
20 (±16 MHz)
20 (±16 MHz)
-
24
-
24
-
-
13/17 (22KHz)
60
-
60
-
-
300
Line power
(automatic) I. max.
V=mA
Mains voltage/frequency
V~/Hz
196 - 264 / 50-60
Max. current
mA
255
Max. power consumption
W
26
Max. working temperature
ºC
45
Automatic adjustment (Depending on
the wished level of exit and the signal of
entrance).
40 (a 862MHz)
IP 20
Protection index
*
9
** Programmable adjustment.
*** The output level depends on the nº of
channels.
15
Amplification
T.12 SINGLE CHANNEL AMPLIFIERS
Televes launches the new T.12 single channel
amplifiers, an advanced evolution of a product range, the
result of Televes’ broad experience accumulated since 1981
when this technology was first introduced.
Main features
Completely compatible with the previous model (T03)
and its PSU.
Great reliability, thanks to its robotised manufacturing
process.
Improved screening.
Modular and expandable system.
Powering of up to 24 modules, from a PSU.
Line powering of mastheads.
REF.DESCRIPTION
508012 IF BAND AMPLIFIER T12
IF
508112 BI BAND AMPLIFIER T12
BI
508212 FM BAND AMPLIFIER T12
FM
509912 DAB BAND AMPLIFIER T12
DAB
508312 BIII BAND AMPLIFIER T12
508712 LOW S BAND AMPLIFIER T12
BIII
LOW SB
508812 HIGH S BAND AMPLIFIER T12
HIGH SB
508912 HYPERBAND AMPLIFIER T12
HYPERB.
509812 SELECTIVE SINGLE CHANNEL AMPLIFIER
UHF
508612 SINGLE CHANNEL/MULTICHANNEL AMP.
UHF
549812 SWITCHED PSU T12
509512 SELECTIVE SINGLE CH. AMP. W/ AGC T12
UHF
509712 SINGLE CHANNEL AMP. W/ AGC T12
UHF
16
LTE READY PRODUCTS
ref. 508612
ref. 508612
ref. 508012
With the T.12 single channel amplifiers Televes has
produced a product that achieves an outstanding
performance in the treatment of the signal, with
precise and simple frequency adjustments.
The T.12 modules are manufactured in latest
generation robotised lines and are subject to the
strictest quality control, a guarantee of reliability
and stability with no precedents in this industry.
Ready for the upcoming introduction of LTE
services, this product carries Televes’ LTE Ready
stamp.
Televes has put a lot of trust in the T.12
modules, the new reference on single
channel amplifiers in the market.
ReferencEs
508112 508212 508312 508712 509912 508812 508912 508612 509812 508012
fw
MHz
BW
MHz
7
7
37
7
8
8 56
8
950 - 2150
8
8
50
35
45
58
45
58
58
50
55
35 50
57
57
35
35
35
35
35
35
35
30
30
20
30
30
-
-
-
-
-
-
-
-
-
0 12
-
-
A
123*
114*
123*
125*
-
124*
125*
125 111*
121*
125
121
D
-
-
-
-
114***
-
-
118 102*
115*
dBµV
EQ
118
114
mA
100
400
100
100
V
Vdc
24
13/17
24
24
KHz
-
-
0/22
-
-
IC
mA
70
95
133
90
90
P
dB
Rn+2
dB
Rn+3
* EN 50083-5
124**
I
Rn+1
AGC
950-2150 470-862 470-862
-
dB
Noise figure
470 - 865
7
G
Vout
47 - 88 87.5 - 108 174 - 230 104 - 174 195 - 232 230 - 300 302 - 470
509712 509512
≤1
<3
<3
<1
<3
<1
<1
<3
<2
-
<1
<2
-
-
-
-
-
-
-
>3
> 18
-
>3
>18
> 40
-
> 30
> 30
> 20
>25
> 30
> 15
> 50
-
>25
>50
-
-
-
-
-
-
-
> 45
-
-
>50
-
< 11
< 12.5
<9
<11
NF
dB
<9
AGC
dB
-
** DIN VDE0855/12
30
***di = 50dB (2ch. 4MHz)
17
Distribution
Once 4G services are deployed, there is the possibility that signals will be transmitted from the mobile handset, the so called
uplink, these could filter into the coax distribution network.
Televes recommends the use of the EASY-F connection system for installations perfectly prepared for the deployment of
LTE/4G.
The passive distribution equipment should be selected with
due care and should be correctly screened to avoid the ingress
of signals that could interfere with the TV signals. In this scenario the attenuation might not be the most important parameter.
Certified coaxial cable
CERTIFIED
Model - ReferencE
SK2000plus - 4138
Inner conductor - braid composition
Inner
Ø
mm
conductor
Dielectric
Ø
mm
P.E.
Foil
Coaxial cable with inner conductor made of 100% copper,
high screening attenuation (Class A+) and low losses. Televes’
coaxial cable is subject to strict quality controls. Screening attenuation in excess of 85dB in the UHF and 4G bands makes
it specially useful against the potential risk of LTE/4G interference.
A requirement to give the installer the satisfaction and peace
of mind to guard against LTE/4G signals, has made Televes
certify all the coaxial cable that we supply.
This is why, a coaxial cable with the Televes’ brand is a certified cable, and LTE READY cable.
Braid
4.60 ± 0.05
Al + Polyester
dimensions
G×H×Ø*
24 × 7 × 0.10
coverage
%
82
mm
6.7 ± 0.1 (PVC & LSFH)
Outer
Ø
sheath
Minimum bending
radius
Screening attenuation
Attenuation
Frequency
(MHz)
Cu
1.02 ± 0.016
mm
33.5
Class A+
5
4.8
470
14.0
862
950
dB/100m
18.7
20.5
2150
31.2
3000
35.5
(*) G×H×Ø: strand groups x number of strands x strand’s diameter.
NEW CAI RG-6 APPROVED CABLE
Model - ReferencE
CXT-1 2127
Inner conductor - braid composition
Inner
Ø
mm
conductor
Dielectric
Ø
mm
Foil
Braid
With a copper clad steel 1mm inner conductor and aluminium
braid it is the perfect cable for single dwelling units.
A screening attenuation of 75dB (Class A) in the UHF and 4G
bands it gives this cable an optimum protection against potential harmful interference.
18
LTE READY PRODUCTS
1.00 ± 0.02
4.7 ± 0.1
Al + Polyester
dimensions
G×H×Ø*
coverage
%
77
mm
6.7 ± 0.2 (PVC)
Outer
Ø
sheath
Minimum bending radius
mm
Screening attenuation
Attenuation
Frequency
(MHz)
Cu CLAD STEEL
16 × 8 × 0.12
33
Class A
50
5
200
9.5
800
1000
dB/100m
20.5
23
2050
35
2300
37
ONLY A CERTIFIED CABLE
GUARANTEES THE QUALITY OF THE INSTALLATION
TELEVES’ CABLE CERTIFICATION CENTER
At Televes we consider that the best way to guarantee the performance of a coaxial cable is through the quality
control in all the manufacturing processes. In the LTE/4G scenario, only the certified cable will ensure the quality of
the signal.
A cable with Televes on it, is a certified cable.
Copper quality: tests of DC performance at high
and low frequencies generate parameters that help
us evaluate the purity of the copper.
Quality of the gas injection (foam): through the
test of dielectric rigidity we can detect alterations in
the isolation between the inner conductor and the
foil.
SCREENING ATTENUATION OF THE CABLES
SCREENING ATTENUATION (dB)
Hence why, Televes, in its cable
certification center performs the
following tests:
FREQUENCY (MHz)
Limit
Screening attenuation
Fig.1 Graph of screening attenuation.
Copper+Polyester foil: the continuity tests highlight possible breaks in the foil that could deteriorate
the conductivity to ground or the screening against
interference.
Braid interlacing: the interlacing is one of the
characteristics that can influence more the quality of
the shielding. Its effectiveness can be measured by
the screening attenuation (Fig.1).
Quality of the outer sheath: a complex tool
detects variations in the walls of the outer sheath,
which allows us to measure the homogeneity and
symmetry of the outer sheath (Fig.2)
Attenuation and length: the attenuation tests
measure the uniformity of the impedance, preserving the quality of the signals travelling in the coaxial
cable.
In addition to the tests of intrinsic quality, in the
coaxial cable certification center we guarantee the
length of the cable supplied and the serigraphy and
packaging.
Fig.2 Detail of asimetry of the coverage
detected during the tests in the center.
All the information generated during the certification processes,
will be stored through a traceability system that allows us to find
out all the data of each and every drum produced.
19
SAFE AND SHIELDED CONNECTION
Pro EASY f CONNECTORS
The Pro Easy F connectors ensure the
maximum quality in the connection,
giving exceptional screening to the TV
signals in the installation as its screening
efficiency exceeds the requirements of
CLASS A.
No push on or detachable components,
which simplifies its fitting, eases and
assures its connection.
Screening of the male IEC connector ref.413201
Screening of the male IEC connector ref.413201
Safe
connection:
Electrically
perfect:
Save time and cost in the
installation.
100% robotised manufacturing
is a reasurance of its quality.
Ensure the reliability of the
connection and avoid the
need for future call backs.
Completely screened to avoid
LTE/4G effects.
The peace of mind of a job
well done.
Easy
and quick to fit:
 One screw.
 Connection always visible.
 No push on pieces.
 No detachable pieces.
20
LTE READY PRODUCTS
REF.DESCRIPTION
413201 “PRO EasyF” Connector “IEC” Ø 9,5mm
Male elbow screened
413301 “PRO EasyF” Connector “IEC” Ø 9,5mm Female elbow screened
413401 “PRO EasyF” Connector “Quick F” Elbow screened
FLY LEADS
Despite having had the installation adapted to avoid the
influence of LTE/4G, the weakest point will be the leads
connecting the outlet plate with the TV.
The “LTE ready” leads are made with T200 Class A coaxial cable
and screened Pro Easy-F connectors.
REF.DESCRIPTION
431001 “IEC” coaxial lead Ø 9,5mm Screened elbow M
ale-Female 1.5m
431002 “IEC” coaxial lead Ø 9,5mm Screened elbow M
ale-Female 2.5m
Both components guarantee the best screening possible.
TYPE OF LEAD
Class A lead
The quality of these components is now key and would be a
mistake to use leads of doubtful quality, many of these don’t
have screening or foil.
Class B lead
IEC CONNECTOR
From 30 to 1000MHz
From 1 to 3GHz
From 30 to 1000MHz
From 1 to 3GHz
> 85
dB
> 65
>75
> 55
For the measurement of the quality of screening of these
leads with IEC connectors we use the following standards EN
60966-2-5 and N 60966-2-4.
The specifications are reproduced in the table attached.
Theses parameters are not achieved by any other leads
currently available in the market.
21
Distribution
OUTLET PLATEs
The special manufacturing process and design of our outlet
plates guarantees the protection of the TV and satellite signal.
DOES NOT ALLOW THE DIGITAL QUALITY TO
VANISH IN THE CONNECTIONS.
Cable connection with easy F
Automated production for highest reliability
Lateral opening clamp for easy fitting
A manufacturer of outlet plates that
offers solutions for every scenario
AUTOMATED MANUFACTURING PROCESS
SPECIFICATIONS
Product
Ref.522610 TV / SAT DC terminal outlet plate
Pass band (MHz)
1/1
1,5
47-790
11 (2 through) / 29 (2 through)
(2,5 through)
splitters and taps
In the Easy F splitter and tap range special care has
been taken in the screening of the circuit, also done
with the connection system.
The zamak chassis allows perfect screening across
the whole frequency range plus its connection
by means of the Easy F system; simplifies the
installation with no detriment to the screening
efficiency..
LTE READY PRODUCTS
IF SAT
47-790 / 950-2150
Ref.523110 TV - FM through outlet plate
22
Attenuation (dB)
TV/FM
DTT Reception
Several studies and test have been carried out in Europe with regards to the influence of pulsed 4G signals over the performance
of demodulators built into DTT receivers and adaptors.
These studies concluded that the performance of DTT receivers, TVs and adaptors are subject to interference from LTE/4G, even
with optimum screening of the installation.
This is the reason why by design the characteristics of the LTE/4G signals must be taken into account in order to avoid signal
break-up or pixelation.
zas hd RECEIVER
European manufacturing, with strict quality controls and state of the art
electronic design make the zAs HD the ideal receiver to allow the viewing of
TV despite changing broadcast scenarios like deployment of LTE/4G.
23
DTT processing
The transmodulator/regenerator is an element that could be used in those instances where standard mitigation techniques
(filtering) can’t be used or don’t achieve the desired results. This alternative allows the re-construction of the original signal, so
that the original services are re-modulated at the headend. The regenerator even allows the installer to edit parameters of the
multiplexed services. It is the ideal solution to re-establish the quality of the affected signal.
t.0X transmodulator / regenerator cofdm / cofdm
The transmodulator COFDM/COFDM CI (Ref.563401) adapts the transport stream
to the requirements of the DVB-T transmission through the selective deletion of
services from the received DTT MUX, to avoid the reception (and storage) by the DTT
receivers and TVs.
By means of its CI interface and the CAM module, those encrypted DTT services
could be decrypted and distributed as free to air.
The COFDM regenerators allow the
implementation of a flexible solution
for the hospitality sector in which the
client can decide which services to
distribute.
PWR
5629
6 x 563401
5575
CAM
DTT
Input
24
LTE READY PRODUCTS
DVB-T
Demodulator
CI
Interface
TS Processing
COFDM
Modulator
Up
Converter
DTT
Output
Measurement
Even more important with the deployment of the 4G telephony network and due to the pulsant nature of this interference signal
only a spectrum analyzer capable of capturing up to 20MHz of bandwidth in less than 10 miliseconds will be able to detect it.
NEW SPECTRUM ANALYZER H60, WITH DIGITAL PROCESSING
Unprecedent speed and mathematical precision in all its measurements...
The spectrum analyzer recommend by Televes to analyze the TV signals in the communal system during 4G deployment.
The Digital Processing allows an uncomparable precision and speed in the analysis.
the choice is CLEAR
www.televesh60.com
25
Spectrum analyzer up to 3.3 GHz
TILT function
Network frequency attenuation.
MPEG4 with common interface. HD video.
HDMI output.
Selective optical interface.
DVB-T2 demodulation.
5.7” of high resolution.
Digital processing.
Remote control of measurements via IP
Ideal for monitoring incoming signals and broadband networks.
Leave your H60 connected to a system and control to it remotely.
Once the job is done, export your results to any PC/laptop by means
of the HSuite SW (included).
www.televesh60.com
26
LTE READY PRODUCTS
27
Product Guide
TELEVES SA (HEAD OFFICE)
Rúa B. de Conxo, 17
15706 Santiago de Compostela (SPAIN)
Tel: (+34) 981 52 22 00
Fax: (+34) 981 52 22 62
E-mail: televes@televes.com
TELEVES (U.K.) LTD.
11 HILL STREET INDUSTRIAL ESTATE
NP44 7 PG - CWMBRAN, GWENT (UK) (CRF)
Tel: (+44) 01 633 87 58 21
Fax: (+44) 01 633 86 63 11
E-mail: televes.uk@televes.com
www.televes.com
FI:042013 CMP: 06000307